Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-06-21
This series contains updates to ice driver only.
Marcin fixes GTP filters by allowing ignoring of the inner ethertype field.
Wojciech adds VSI handle tracking in order to properly distinguish similar
filters for removal.
Anatolii removes ability to set 1000baseT and 1000baseX fields
concurrently which caused link issues. He also disallows setting
channels to less than the number of Traffic Classes which would cause
NULL pointer dereference.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: ethtool: Prohibit improper channel config for DCB
ice: ethtool: advertise 1000M speeds properly
ice: Fix switchdev rules book keeping
ice: ignore protocol field in GTP offload
====================
Link: https://lore.kernel.org/r/20220621224756.631765-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.
According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.
In addition to that, commit b6e0c419f0 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.
Fixes: b6e0c419f0 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Under CONFIG_FORTIFY_SOURCE=y and CONFIG_UBSAN_BOUNDS=y, Clang is bugged
here for calculating the size of the destination buffer (0x10 instead of
0x14). This copy is a fixed size (sizeof(struct fw_section_info_st)), with
the source and dest being struct fw_section_info_st, so the memcpy should
be safe, assuming the index is within bounds, which is UBSAN_BOUNDS's
responsibility to figure out.
Avoid the whole thing and just do a direct assignment. This results in
no change to the executable code.
[This is a duplicate of commit 2c0ab32b73 ("hinic: Replace memcpy()
with direct assignment") which was applied to net-next.]
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Tom Rix <trix@redhat.com>
Cc: llvm@lists.linux.dev
Link: https://github.com/ClangBuiltLinux/linux/issues/1592
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Link: https://lore.kernel.org/r/20220616052312.292861-1-keescook@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 8fc74d1863.
BAR0 is the main (only?) register bank for this device. We most
obviously can't unmap it before the netdev is unregistered.
This was pointed out in review but the patch got reposted and
merged, anyway.
The author of the patch was only testing it with a QEMU model,
which I presume does not emulate enough for the netdev to be brought
up (author's replies are not visible in lore because they kept sending
their emails in HTML).
Link: https://lore.kernel.org/all/20220616085059.680dc215@kernel.org/
Fixes: 8fc74d1863 ("drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current implementation ice_update_phy_type enables all link modes
for selected speed. This approach doesn't work for 1000M speeds,
because both copper (1000baseT) and optical (1000baseX) standards
cannot be enabled at once.
Fix this, by adding the function `ice_set_phy_type_from_speed()`
for 1000M speeds.
Fixes: 48cb27f2fd ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adding two filters with same matching criteria ends up with
one rule in hardware with act = ICE_FWD_TO_VSI_LIST.
In order to remove them properly we have to keep the
information about vsi handle which is used in VSI bitmap
(ice_adv_fltr_mgmt_list_entry::vsi_list_info::vsi_map).
Fixes: 0d08a441fb ("ice: ndo_setup_tc implementation for PF")
Reported-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 34a897758e ("ice: Add support for inner etype in switchdev")
added the ability to match on inner ethertype. A side effect of that change
is that it is now impossible to add some filters for protocols which do not
contain inner ethtype field. tc requires the protocol field to be specified
when providing certain other options, e.g. src_ip. This is a problem in
case of GTP - when user wants to specify e.g. src_ip, they also need to
specify protocol in tc command (otherwise tc fails with: Illegal "src_ip").
Because GTP is a tunnel, the protocol field is treated as inner protocol.
GTP does not contain inner ethtype field and the filter cannot be added.
To fix this, ignore the ethertype field in case of GTP filters.
Fixes: 9a225f81f5 ("ice: Support GTP-U and GTP-C offload in switchdev")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It should return error code in error path in axienet_probe().
Fixes: 00be43a74c ("net: axienet: make the 64b addresable DMA depends on 64b archectures")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220616062917.3601-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-06-14
This series contains updates to ice driver only.
Michal fixes incorrect Tx timestamp offset calculation for E822 devices.
Roman enforces required VLAN filtering settings for double VLAN mode.
Przemyslaw fixes memory corruption issues with VFs by ensuring
queues are disabled in the error path of VF queue configuration and to
disabled VFs during reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
'bgmac' is part of a managed resource allocated with bgmac_alloc(). It
should not be freed explicitly.
Remove the erroneous kfree() from the .remove() function.
Fixes: 34a5102c32 ("net: bgmac: allocate struct bgmac just once & don't copy it")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/a026153108dd21239036a032b95c25b5cece253b.1655153616.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Disable VF's RX/TX queues, when VIRTCHNL_OP_CONFIG_VSI_QUEUES fail.
Not disabling them might lead to scenario, where PF driver leaves VF
queues enabled, when VF's VSI failed queue config.
In this scenario VF should not have RX/TX queues enabled. If PF failed
to set up VF's queues, VF will reset due to TX timeouts in VF driver.
Initialize iterator 'i' to -1, so if error happens prior to configuring
queues then error path code will not disable queue 0. Loop that
configures queues will is using same iterator, so error path code will
only disable queues that were configured.
Fixes: 77ca27c417 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Suggested-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VLAN filtering features, that is C-Tag and S-Tag, in DVM mode must be
both enabled or disabled.
In case of turning off/on only one of the features, another feature must
be turned off/on automatically with issuing an appropriate message to
the kernel log.
Fixes: 1babaf77f4 ("ice: Advertise 802.1ad VLAN filtering and offloads for PF netdev")
Signed-off-by: Roman Storozhenko <roman.storozhenko@intel.com>
Co-developed-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The offset was being incorrectly calculated for E822 - that led to
collisions in choosing TX timestamp register location when more than
one port was trying to use timestamping mechanism.
In E822 one quad is being logically split between ports, so quad 0 is
having trackers for ports 0-3, quad 1 ports 4-7 etc. Each port should
have separate memory location for tracking timestamps. Due to error for
example ports 1 and 2 had been assigned to quad 0 with same offset (0),
while port 1 should have offset 0 and 1 offset 16.
Fix it by correctly calculating quad offset.
Fixes: 3a7496234d ("ice: implement basic E822 PTP support")
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Both RIF and ACL flow counters use a 24-bit SW-managed counter address to
communicate which counter they want to bind.
In a number of Spectrum FW releases, binding a RIF counter is broken and
slices the counter index to 16 bits. As a result, on Spectrum-2 and above,
no more than about 410 RIF counters can be effectively used. This
translates to 205 netdevices for which L3 HW stats can be enabled. (This
does not happen on Spectrum-1, because there are fewer counters available
overall and the counter index never exceeds 16 bits.)
Binding counters to ACLs does not have this issue. Therefore reorder the
counter allocation scheme so that RIF counters come first and therefore get
lower indices that are below the 16-bit barrier.
Fixes: 98e60dce4d ("Merge branch 'mlxsw-Introduce-initial-Spectrum-2-support'")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220613125017.2018162-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The AMD XGbE driver currently counts the number of interrupts assigned
to the device by inspecting the pdev->resource array. Since commit
a1a2b7125e ("of/platform: Drop static setup of IRQ resource from DT
core") removed IRQs from this array, the driver now attempts to get all
interrupts from 1 to -1U and gives up probing once it reaches an invalid
interrupt index.
Obtain the number of IRQs with platform_irq_count() instead.
Fixes: a1a2b7125e ("of/platform: Drop static setup of IRQ resource from DT core")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lore.kernel.org/r/20220609161457.69614-1-jean-philippe@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes: 6e144b47f5 (octeontx2-pf: Add support for adaptive interrupt coalescing)
Added support for VF interfaces as well.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_64BIT is not sufficient for checking for availability of
iowrite64() and friends.
Also, the out_addr helpers need to be inline.
Fixes: b690f8df64 ("net: axienet: Use iowrite64 to write all 64b descriptor pointers")
Signed-off-by: David S. Miller <davem@davemloft.net>
According to commit f735c40ed9 ("net: axienet: Autodetect 64-bit DMA
capability") and AXI-DMA spec (pg021), on 64-bit capable dma, only
writing MSB part of tail descriptor pointer causes DMA engine to start
fetching descriptors. However, we found that it is true only if dma is in
idle state. In other words, dma would use a tailp even if it only has LSB
updated, when the dma is running.
The non-atomicity of this behavior could be problematic if enough
delay were introduced in between the 2 writes. For example, if an
interrupt comes right after the LSB write and the cpu spends long
enough time in the handler for the dma to get back into idle state by
completing descriptors, then the seconcd write to MSB would treat dma
to start fetching descriptors again. Since the descriptor next to the
one pointed by current tail pointer is not filled by the kernel yet,
fetching a null descriptor here causes a dma internal error and halt
the dma engine down.
We suggest that the dma engine should start process a 64-bit MMIO write
to the descriptor pointer only if ONE 32-bit part of it is written on all
states. Or we should restrict the use of 64-bit addressable dma on 32-bit
platforms, since those devices have no instruction to guarantee the write
to LSB and MSB part of tail pointer occurs atomically to the dma.
initial condition:
curp = x-3;
tailp = x-2;
LSB = x;
MSB = 0;
cpu: |dma:
iowrite32(LSB, tailp) | completes #(x-3) desc, curp = x-3
... | tailp updated
=> irq | completes #(x-2) desc, curp = x-2
... | completes #(x-1) desc, curp = x-1
... | ...
... | completes #x desc, curp = tailp = x
<= irqreturn | reaches tailp == curp = x, idle
iowrite32(MSB, tailp + 4) | ...
| tailp updated, starts fetching...
| fetches #(x + 1) desc, sees cntrl = 0
| post Tx error, halt
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reported-by: Max Hsu <max.hsu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it is not safe to config the IP as 64-bit addressable on 32-bit
archectures, which cannot perform a double-word store on its descriptor
pointers. The pointer is 64-bit wide if the IP is configured as 64-bit,
and the device would process the partially updated pointer on some
states if the pointer was updated via two store-words. To prevent such
condition, we force a probe fail if we discover that the IP has 64-bit
capability but it is not running on a 64-Bit kernel.
This is a series of patch (1/2). The next patch must be applied in order
to make 64b DMA safe on 64b archectures.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reported-by: Max Hsu <max.hsu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in driver initialization process, driver will set shapping
parameters of tm port to default speed read from firmware. However, the
speed of SFP module may not be default speed, so shapping parameters of
tm port may be incorrect.
To fix this problem, driver sets new shapping parameters for tm port
after getting exact speed of SFP module in this case.
Fixes: 88d10bd6f7 ("net: hns3: add support for multiple media type")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hns3 driver misuses the VF rss size to initialize the PF rss size
in hclge_tm_vport_tc_info_update. So this patch fix it by checking the
vport id before initialization.
Fixes: 7347255ea3 ("net: hns3: refactor PF rss get APIs with new common rss get APIs")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, settings parameters of schedule mode, dwrr, shaper of tm
priority or qset of one tc are only be set when tc is enabled, they are
not restored to the default settings when tc is disabled. It confuses
users when they cat tm_priority or tm_qset files of debugfs. So this
patch fixes it.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tx push is also a ring param. So the original ring param print
info in hns3_is_ringparam_changed should be adjusted.
Fixes: 07fdc163ac ("net: hns3: refactor hns3_set_ringparam()")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unnecessary to push link state to unalive VF, and the VF will
query link state from PF when it being start works.
Fixes: 18b6e31f8b ("net: hns3: PF add support for pushing link status to VFs")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When modify port base vlan, the port base vlan tbl_sta needs to set to
false before removing old vlan, to indicate this operation is not finish.
Fixes: c0f46de30c ("net: hns3: fix port base vlan add fail when concurrent with reset")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-06-09
Grzegorz prevents addition of TC flower filters to TC0 and fixes queue
iteration for VF ADQ to number of actual queues for i40e.
Aleksandr prevents running of ethtool tests when device is being reset
for i40e.
Michal resolves an issue where iavf does not report its MAC address
properly.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: Fix issue with MAC address of VF shown as zero
i40e: Fix call trace in setup_tx_descriptors
i40e: Fix calculating the number of queue pairs
i40e: Fix adding ADQ filter to TC0
====================
Link: https://lore.kernel.org/r/20220609162620.2619258-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Swap around the GRE and VLAN parts in the flow-key offloaded by
the driver to fit in with other tunnel types and the firmware.
Without this change used cases with GRE+VLAN on the outer header
does not get offloaded as the flow-key mismatches what the
firmware expect.
Fixes: 0d630f5898 ("nfp: flower: add support to offload QinQ match")
Fixes: 5a2b930416 ("nfp: flower-ct: compile match sections of flow_payload")
Signed-off-by: Etienne van der Linde <etienne.vanderlinde@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nfp_net_sriov_check is added in nfp_app_get_vf_config which intends
to ensure ivi->vlan_proto and ivi->max_tx_rate/min_tx_rate can be
read from VF config table only when firmware supports corresponding
capability.
However, "nfp_app_get_vf_config" can be called by commands like
"ip a", "ip link set $DEV up" and "ip link set $DEV vf $NUM vlan
$param" (with VF). When using commands above, many warnings
"ndo_set_vf_<cap_x> not supported" would appear if firmware doesn't
support VF rate limit and 802.1ad VLAN assingment. If more VFs are
created, things could get worse.
Thus, this patch add an extra bool parameter for nfp_net_sriov_check
to enable/disable the cap check warning report. Unnecessary warnings
in nfp_app_get_vf_config can be avoided. Valid warnings in kinds of
vf setting function can be reserved.
Fixes: e0d0e1fdf1 ("nfp: VF rate limit support")
Fixes: 59359597b0 ("nfp: support 802.1ad VLAN assingment to VF")
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
gcc-12 started warning about 'tracker' being used uninitialized:
drivers/net/ethernet/mellanox/mlx5/core/lag/lag.c: In function ‘mlx5_do_bond’:
drivers/net/ethernet/mellanox/mlx5/core/lag/lag.c:786:28: warning: ‘tracker’ is used uninitialized [-Wuninitialized]
786 | struct lag_tracker tracker;
| ^~~~~~~
which seems to be because it doesn't track how the use (and
initialization) is bound by the 'do_bond' flag.
But admittedly that 'do_bond' usage is fairly complicated, and involves
passing it around as an argument to helper functions, so it's somewhat
understandable that gcc doesn't see how that all works.
This function could be rewritten to make the use of that tracker
variable more obviously safe, but for now I'm just adding the forced
initialization of it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After reinitialization of iavf, ice driver gets VIRTCHNL_OP_ADD_ETH_ADDR
message with incorrectly set type of MAC address. Hardware address should
have is_primary flag set as true. This way ice driver knows what it has
to set as a MAC address.
Check if the address is primary in iavf_add_filter function and set flag
accordingly.
To test set all-zero MAC on a VF. This triggers iavf re-initialization
and VIRTCHNL_OP_ADD_ETH_ADDR message gets sent to PF.
For example:
ip link set dev ens785 vf 0 mac 00:00:00:00:00:00
This triggers re-initialization of iavf. New MAC should be assigned.
Now check if MAC is non-zero:
ip link show dev ens785
Fixes: a3e839d539 ("iavf: Add usage of new virtchnl format to set default MAC")
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After PF reset and ethtool -t there was call trace in dmesg
sometimes leading to panic. When there was some time, around 5
seconds, between reset and test there were no errors.
Problem was that pf reset calls i40e_vsi_close in prep_for_reset
and ethtool -t calls i40e_vsi_close in diag_test. If there was not
enough time between those commands the second i40e_vsi_close starts
before previous i40e_vsi_close was done which leads to crash.
Add check to diag_test if pf is in reset and don't start offline
tests if it is true.
Add netif_info("testing failed") into unhappy path of i40e_diag_test()
Fixes: e17bc411ae ("i40e: Disable offline diagnostics if VFs are enabled")
Fixes: 510efb2682 ("i40e: Fix ethtool offline diagnostic with netqueues")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If ADQ is enabled for a VF, then actual number of queue pair
is a number of currently available traffic classes for this VF.
Without this change the configuration of the Rx/Tx queues
fails with error.
Fixes: d29e0d233e ("i40e: missing input validation on VF message handling by the PF")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Procedure of configure tc flower filters erroneously allows to create
filters on TC0 where unfiltered packets are also directed by default.
Issue was caused by insufficient checks of hw_tc parameter specifying
the hardware traffic class to pass matching packets to.
Fix checking hw_tc parameter which blocks creation of filters on TC0.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
see warning:
| drivers/net/ethernet/amd/xgbe/xgbe-drv.c:2787:43: warning: format specifies
| type 'unsigned short' but the argument has type 'int' [-Wformat]
| netdev_dbg(netdev, "Protocol: %#06hx\n", ntohs(eth->h_proto));
| ~~~~~~ ^~~~~~~~~~~~~~~~~~~
Variadic functions (printf-like) undergo default argument promotion.
Documentation/core-api/printk-formats.rst specifically recommends
using the promoted-to-type's format flag.
Also, as per C11 6.3.1.1:
(https://www.open-std.org/jtc1/sc22/wg14/www/docs/n1548.pdf)
`If an int can represent all values of the original type ..., the
value is converted to an int; otherwise, it is converted to an
unsigned int. These are called the integer promotions.`
Since the argument is a u16 it will get promoted to an int and thus it is
most accurate to use the %x format specifier here. It should be noted that the
`#06` formatting sugar does not alter the promotion rules.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Justin Stitt <jstitt007@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20220607191119.20686-1-jstitt007@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-06-07
This series contains updates to ixgbe driver only.
Olivier Matz resolves an issue so that broadcast packets can still be
received when VF removes promiscuous settings and removes setting of
VLAN promiscuous, in promiscuous mode, to prevent a loop when VFs are
bridged.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ixgbe: fix unexpected VLAN Rx in promisc mode on VF
ixgbe: fix bcast packets Rx on VF after promisc removal
====================
Link: https://lore.kernel.org/r/20220607181538.748786-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Every iteration of for_each_child_of_node() decrements
the reference count of the previous node.
When break from a for_each_child_of_node() loop,
we need to explicitly call of_node_put() on the child node when
not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: bbd2190ce9 ("Altera TSE: Add main and header file for Altera Ethernet Driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220607041144.7553-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When rx_flag == MTK_RX_FLAGS_HWLRO,
rx_data_len = MTK_MAX_LRO_RX_LENGTH(4096 * 3) > PAGE_SIZE.
netdev_alloc_frag is for alloction of page fragment only.
Reference to other drivers and Documentation/vm/page_frags.rst
Branch to use __get_free_pages when ring->frag_size > PAGE_SIZE.
Signed-off-by: Chen Lin <chen45464546@163.com>
Link: https://lore.kernel.org/r/1654692413-2598-1-git-send-email-chen45464546@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When combining two steering rules into one check
not only do they share the same actions but those
actions are also the same. This resolves an issue where
when creating two different rules with the same match
the actions are overwritten and one of the rules is deleted
a FW syndrome can be seen in dmesg.
mlx5_core 0000:03:00.0: mlx5_cmd_check:819:(pid 2105): DEALLOC_MODIFY_HEADER_CONTEXT(0x941) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x1ab444)
Fixes: 0d235c3fab ("net/mlx5: Add hash table to search FTEs in a flow-group")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The current design does not arm the tracer if traces are available before
the tracer string database is fully loaded, leading to an unfunctional tracer.
This fix will rearm the tracer every time the FW triggers tracer event
regardless of the tracer strings database status.
Fixes: c71ad41ccb ("net/mlx5: FW tracer, events handling")
Signed-off-by: Feras Daoud <ferasda@nvidia.com>
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
FW is not ready, fix was sent too soon.
This reverts commit f05ec8d9d0.
Fixes: f05ec8d9d0 ("net/mlx5e: Allow relaxed ordering over VFs")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The conversion to the dma-mapping API in linux-2.6.11 was incomplete
and left a virt_to_bus() call around. There have been a number of
fixes for DMA mapping API abuse in this driver, but this one always
slipped through.
Change it to just use the existing dma_addr_t pointer, and make it
use the correct types throughout the driver to make it easier to
understand the virtual vs dma address spaces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Link: https://lore.kernel.org/r/20220607090206.19830-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski