Remove imacfb entirely, merging its DMI table into the (otherwise very
similar) efifb driver. This also adds hardware support for many of the
newer Intel Apple hardware. This has been fairly well tested; we've been
shipping it in Fedora for some time.
Signed-off-by: Peter Jones <pjones@redhat.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A memory clock value (MCLK) is changed to a minimum required by a current
mode bandwidth. This usually lowers the MCLK to its minimum (50 MHz) thus
decreasing the card performance. Just leave the MCLK value set by card
BIOS.
The CL-GD5446 Technical Reference Manual point 9.9.1.3 states that if a
pixclock value is close (~1%) to the MCLK or MCLK/2 this may result in a
jitter on the screen. A countermeasure is to use the MCLK as pixclock
source instead of a VCLK. The patch implements this as well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 16bpp mode did not work on the Cirrus cards as the visual type was set
to DIRECTCOLOR instead of TRUECOLOR. The Alpine family used one incorrect
register setting so this 16bpp modes generated wrong horizontal frequency.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The noaccel parameter is already handled if the driver is not built as
module.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move call to pixclock calculation into the cirrusfb_set_par_foo(). It
makes copy of clock registers redundant.
Simplify clock calculations further.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move calculations of CRT register values into the cirrusfb_set_par_foo()
where the values are used.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add __devinit attribute to probing functions. This fixed section mismatch
warning from my previous patch.
Kill one redundant forward declaration.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use modedb for initial mode instead of table of few predefined modes.
Add mode_option module parameter as a step toward unification of frame
buffers' parameters.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The device pointer can be easily obtained from fb_info->device if needed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 24 bpp mode is not implemented. Disallow it in the
cirrusfb_check_var() and remove it from checks.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify clock calculation.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove information about memory size displayed twice each time a display
mode change.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for Intel's 945GME graphics chip to the intelfb driver. I
have assumed that the 945GME is identical to the already-supported 945GM
apart from its PCI IDs; this is based on a quick look at the X driver for
these chips which seems to treat them identically.
The 945GME is used in the ASUS Eee 901, and I coded this in the hope that
I'd be able to use it to get a console at the native 1024x600 resolution
which is not known to the BIOS. I realised too late that the intelfb
driver does not support mode changing on laptops, so it won't be any
use for me.
Signed-off-by: Phil Endecott <spam_from_intelfb@chezphil.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was suggested by Geert Uytterhoeven to avoid overwriting of default
values from the tdfx_fix.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove mutex from the fb_open/fb_release functions as these operations are
mutexed at fb layer.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove mutex from the fb_open/fb_release functions as these operations are
mutexed at fb layer.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move common code outside if/else or switch/case clauses.
Drop checks done twice inside the neofb_check_var().
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
via_utility.c, via_utility.h: support user mode application with
additional information vt1636.c, vt1636.h: setting for chip vt1636
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the macro MMIO_OUT32, and replace it with writel() function.
And replace "u32" with "unsigned long" in writel() function (original
MMIO_OUT32 marco) for avoiding warning message in 64bit OS.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correct by following Jiri Slaby's suggestions.
Initialization, remove and some other important functions of viafb.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makefile for drivers/video/via/
share.h: shared macro for viafb
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
iface.c, iface.h: support getting video memory from backdoor.
ioctl.c, ioctl.h: support user mode application with additional information
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Display HW setting and other chips initialization.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dvi.c, dvi.h: TMDS generic process and setting.
global.c, global.h: define global variabls.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Header file of information about via chipsets and debug function.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modified drivers/video/Makefile and drivers/video/Kconfig.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce panning function by deleting checks done by higher layer and
folding remaining function into the called one.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bug was in fb_ddc and was fixed by commit
b64d70825a (fb_ddc: fix DDC lines quirk) so
the workaround in radeonfb can be removed now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new internal mechanism to gpiolib to support low power
operations by letting gpio_chip instances see when their GPIOs
are in use. When no GPIOs are active, chips may be able to
enter lower powered runtime states by disabling clocks and/or
power domains.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Magnus Damm" <magnus.damm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This updates most of the OMAP drivers which are in mainline to switch to
using the cross-platform GPIO calls instead of the older OMAP-specific
ones.
This is all fairly brainless/obvious stuff. Probably the most interesting
bit is to observe that the omap-keypad code seems to now have a portable
core that could work with non-OMAP matrix keypads. (That would improve
with hardware IRQ debouncing enabled, of course...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new gpiolib mechanism: gpio_chip instances can provide mappings
between their (input) GPIOs and any associated IRQs. This makes it easier
for platforms to support IRQs that are provided by board-specific external
chips instead of as part of their core (such as SOC-integrated GPIOs).
Also update the irq_to_gpio() description, saying to avoid it because it's
not always supported.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the I2C external GPIO expander drivers register themselves at
subsys_initcall() time when they're statically linked.
SOC-integrated GPIOs are available starting very early -- early in
arch_initcall() at latest, but often even before initcalls start to run --
so this improves consistency, so more subsystems can rely on GPIOs in
their own subsys_initcall() code.
(This isn't a theoretical problem. This is one of several patches needed
to resolve oopsing observed when statically linking kernels on a DaVinci
EVM. Its pcf857x GPIOs needed to be available well before some other
drivers initialized.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This is the generic part which changes gpiolib and the fallback
implementation only.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a small race and code ugliness in max7301: pins are reconfigured
after the chip is registered. Swap these calls so that the device is
registered in correct state.
Also this fixes the comile-time warning about unchecked gpiochip_remove.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New style conversion and reformatting as per indent --linux-style
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New style conversion and reformatting as per indent --linux-style
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The non-functional periodic IRQ support was previously removed from the
AT91RM9200 RTC driver. Remove the remaining AT91_RTC_FREQ definition.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Cc: David Brownell: <david-b@pacbell.net>
Cc: Alessandro Zummo: <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for M41T65 Real Time Clock chip.
The main differences I see between the M41T65 and M41T80 are that:
1) The M41T65 watchdog timer has three bits controlling resolution
(versus two for the M41T80).
2) There is no register 0x13 for controlling square-wave output.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of it use CONFIG_PPC instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the rtc framework consistent about disabling 1/second update IRQs
that may have been activated through the /dev interface, when that /dev
file is closed. (It may have closed because of coredump, etc.) This was
previously done only for emulated update IRQs ... now, do it always.
Also comment the current policy: repeating IRQs (periodic, update) that
userspace enabled will be cleanly disabled, but alarms are left alone.
Such repeating IRQs are a constant and pointless system load.
Update some RTC drivers to remove now-needless release() methods. Most
such methods just enforce that policy. The others all seem to be buggy,
and mistreat in-kernel clients of periodic or alarm IRQs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Sharp <andy.sharp@onstor.com>
Cc: Angelo Castello <angelo.castello@st.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for the Ricoh R2025S/D series of I2C RTCs, produced by
Ricoh Japan and described at:
http://www.ricoh.co.jp/LSI/product_rtc/2wire/r2025x/
This series has very minor deviations from the rest of the RS5C chips,
most of which have to do with the oscillator, which was abstracted away in
an earlier patch.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Brownell <david-b@pacbell.net>
Tested-by: Riku Voipio <riku.voipio@movial.fi>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc-rs5c372 presently depends on I2C master mode transfers, despite the
fact that these RTCs frequently find themselves on SMBus-only adapters.
Given that the only capabilities that were checked were for I2C_FUNC_I2C,
it's assumed that most of the adapters that are currently using this
driver are fairly sane, and are able to handle SMBus emulation (though we
adjust the default capabilities to check for I2C_FUNC_SMBUS_EMUL anyways,
which is the vast majority of them. The adapters that don't have their
own ->smbus_xfer() fall back on the ->master_xfer() through the emulated
transfer).
The special case is iop3xx, which has more than its fair share of hacks
within this driver, it remains untested -- though also claims to support
emulated SMBus accesses. The corner case there is rs5c_get_regs() which
uses access mode #3 for transferring the register state, while we use mode
#1 for SMBus.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: David Brownell <david-b@pacbell.net>
Tested-by: Riku Voipio <riku.voipio@movial.fi>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
HPET_RTC_IRQ is no longer needed; HPET_EMULATE_RTC suffices and is more
correct. (http://bugzilla.kernel.org/show_bug.cgi?id=11111)
Note that when using the legacy RTC driver, platforms don't really do a
dynamic switch between HPET and non-HPET modes based on whether HPET
hardware actually exists ... only rtc-cmos (using the new RTC framework)
currently switches that way.
So this reflects bitrot in that legacy code, for x86/ia64: kernels with
HPET support configured (e.g. for a clocksource) can't get IRQs from the
legacy RTC driver unless they really have HPET hardware. (The obvious
workaround is to not use the legacy RTC driver on those platforms when you
configure HPET ... unless you know the target really has a HPET.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove NOP methods from rtc-pl030 and rtc-pl031 drivers;
this is pure wasted code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the ds1307 driver with alarm support for ds1337/ds1339. This uses
the first alarm (there are two), and matches on seconds, minutes, hours,
and day-of-month. Tested on ds1339.
[dbrownell@users.sourceforge.net: add comments; fixup style, valid irq
checks, debug dumps; lock; more careful IRQ shutdown; switch BCD2BIN to
bcd2bin (and vice versa); ENOTTY not EINVAL.]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Dallas DS3234 chip - extremely accurate SPI bus RTC
with integrated crystal and SRAM.
[akpm@linux-foundation.org: don't use BIN2BCD/BCD2BIN]
Signed-off-by: Dennis Aberilla <denzzzhome@yahoo.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Validating clients with black magic register checks doesn't make much
sense for new-style i2c driver and has been known to fail on valid NXP
pcf8563 chips. This patch removes the client validation code.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The I2O ioctls assume 32bits. In itself that is fine as they are old
cards and nobody uses 64bit. However on LKML it was noted this
assumption is also made for allocated memory and is unsafe on 64bit
systems.
Fixing this is a mess. It turns out there is tons of crap buried in a
header file that does racy 32/64bit filtering on the masks.
So we:
- Verify all callers of the racy code can sleep (i2o_dma_[re]alloc)
- Move the code into a new i2o/memory.c file
- Remove the gfp_mask argument so nobody can try and misuse the function
- Wrap a mutex around the problem area (a single mutex is easy to do and
none of this is performance relevant)
- Switch the remaining problem kmalloc holdout to use i2o_dma_alloc
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the SPI external GPIO expander drivers register themselves at
subsys_initcall() time when they're statically linked, and make the SPI
core do its driver model initialization earlier so that's safe.
SOC-integrated GPIOs are available starting very early -- often before
initcalls start to run, or earily in arch_initcall() at latest -- so this
improves consistency, letting more subsystems rely on GPIOs being usable
by their own subsys_initcall() code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to orion_spi for the 88F6183 ARM SoC by adding code to work
around a 6183-specific erratum.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the chip info structure data optional by providing reasonable
defaults. Improve corresponding documentation, and highlight the drawback
of not providing explicit chipselect control.
DMA can determine appropriate dma_burst_size and thresholds automatically
so use DMA even if dma_burst_size is not specified.
Signed-off-by: Vernon Sauder <VernonInHand@gmail.com>
Reviewed-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor fixes: remove redundant local variable initialization, fix "can not"
to what I _think_ is a preferred spelling, output IRQ number if requesting
it failed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a pin configuration callback for the s3c24xx SPI driver, as there are
several options depending on the channel and the chip in use.
This is needed as the controller may not have been setup by the initial
bootloader and the fact that the SPI controller gets reset over
suspend/resume into slave mode but the GPIO function registers do not.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify spi_write_then_read() to use one transfer. This speeds up all
callers, and is a minor code shrink.
Signed-off-by: Vernon Sauder <Vernon.Sauder@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore
remove the dead code associated with !CONFIG_PPC_MERGE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
People can use the real name an an index into MAINTAINERS to find the
current email address.
Signed-off-by: Francois Cami <francois.cami@free.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only three of Atmel's AT91 processors (SAM9263, SAM9RL and CAP9) include a
PWM controller.
It should therefore only be possible to enable the misc/atmel_pwm.c driver
on those processors (and not all AT91 processors).
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is written in the Documentation/sysrq.txt that oom-killer is enabled
when we set "64" in /proc/sys/kernel/sysrq:
<Documentation/sysrq.txt>
Here is the list of possible values in /proc/sys/kernel/sysrq:
64 - enable signalling of processes (term, kill, oom-kill)
^^^^^^^^
but enable_mask is not set in sysrq_moom_op.
Signed-off-by: Naohiro Ooiwa <nooiwa@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using "def_bool n" is pointless, simply using bool here appears more
appropriate.
Further, retaining such options that don't have a prompt and aren't
selected by anything seems also at least questionable.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the '%pF' format to get rid of an "#ifdef DEBUG" and make some printks
atomic.
This removes the last in-tree uses of print_fn_descriptor_symbol(). I
marked print_fn_descriptor_symbol() deprecated and scheduled it for
removal next year to give time for out-of-tree modules to be updated.
parisc's print_fn_descriptor_symbol() is currently broken there (it needs
to dereference the function pointer similar to ia64 and power). This
patch shouldn't make anything worse, but it means we need to fix
dereference_function_descriptor() instead of print_fn_descriptor_symbol()
to get meaningful initcall_debug output.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems this is the right way around because otherwise the len usage in
the outer loop would be pretty pointless.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EEEPC_LAPTOP uses RFKILL, so the former should depend on RFKILL.
Build errors happen when EEEPC_LAPTOP=y and RFKILL=m.
eeepc-laptop.c:(.text+0xd5a7b): undefined reference to `rfkill_allocate'
eeepc-laptop.c:(.text+0xd5b04): undefined reference to `rfkill_register'
eeepc-laptop.c:(.text+0xd5b48): undefined reference to `rfkill_allocate'
eeepc-laptop.c:(.text+0xd5bd4): undefined reference to `rfkill_register'
eeepc-laptop.c:(.text+0xd5ece): undefined reference to `rfkill_unregister'
eeepc-laptop.c:(.text+0xd5ef6): undefined reference to `rfkill_unregister'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Karol Kozimor <sziwan@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mmap() doesn't work as expected for UIO_MEM_LOGICAL or UIO_MEM_VIRTUAL
mappings. The offset into the memory needs to be added, otherwise
uio_vma_fault always returns the first page only. Note that for UIO
userspace calls mmap() with offset = N * getpagesize() to access
mapping N. This must be compensated when calculating the offset. A
comment was added to explain this since it is not obvious.
Signed-off-by: Andrew G. Harvey <agh@cisco.com>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a new version of the patch to support the Automata Sercos III
PCI card driver. I now check that the IRQ is enabled before accepting
the interrupt.
I still use a logical OR to store the enabled interrupts and I've
added a second use of a logical OR when restoring the enabled
interrupts. I added an explanation of why I do this in comments at the
top of the source file.
Since I use a logical OR, I also removed the extra checks if the
Interrupt Enable Register and ier0_cache are 0.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The generic UIO platform device driver should be given a unique driver ID and
not just "uio". This is especially important since we now have a similar driver
named uio_pdrv_genirq. Currently, there's no user of this driver in the
mainline kernel.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an "offset" attribute for UIO mappings. It shows the
difference between the actual start address of the memory and the start
address of the page.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI core wants to reorder the devices in the bus list. So move this
functionality out of the pci core and into the driver core so that
anyone else can also do this if needed. This also lets us change how
struct device is attached to drivers in the future without messing with
the PCI core.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver core now has this helper function, so might as well use it
instead of forcing the phy code to roll their own version.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When looking at kobject_rename I found two bugs with
that exist when sysfs support is disabled in the kernel.
kobject_rename does not change the name on the kobject when
sysfs support is not compiled in.
kobject_rename without locking attempts to check the
validity of a rename operation, which the kobject layer
simply does not have the infrastructure to do.
This patch documents the previously unstated requirement of
kobject_rename that is the responsibility of the caller to
provide mutual exclusion and to be certain that the new_name
for the kobject is valid.
This patch modifies sysfs_rename_dir in !CONFIG_SYSFS case
to call kobject_set_name to actually change the kobject_name.
This patch removes the bogus and misleading check in kobject_rename
that attempts to see if a rename is valid. The check is bogus
because we do not have the proper locking. The check is misleading
because it looks like we can and do perform checking at the kobject
level that we don't.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a helper that registers simple platform_device w/o resources but with
parent and device data.
This is usefull to cleanup platform code from code that registers such
simple devices as leds-gpio, generic-bl, etc.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This creates the attributes before the uevent is sent.
Signed-off-by: Drew Moseley <dmoseley@mvista.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use sysfs_streq() in bus_find_device_by_name() so trailing newlines
are ignored (E.G. in bind/unbind).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dev_WARN is both compacter and gives better debug information
than just a WARN_ON, since people and tools will copy the device
information message together with the WARN_ON in bug reports.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
device_pm_add() has a WARN_ON that is showing relatively high on
kerneloops.org, but unfortunately the WARN_ON is less than useful
in that it doesn't print any information about what device is causing
the issue.
This patch fixes this by turning the WARN_ON() into the newly
introduces dev_WARN() which will print information about the
device in question.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a quick check for the driver<->device match before
taking the locks and doin gthe expensive checks. Taking the lock hurts
in asynchronous boot context where the device lock gets hit; one of the
init functions takes the lock and goes to do an expensive hardware init;
the other init functions walk the same PCI list and get stuck on the
lock as a result.
For the common case, we can know there's no chance whatsoever of a match
if the device isn't in the drivers ID table... so this patch does that
check as a best-effort-avoid-the-lock approach.
Bootcharts for before and after can be seen at
http://www.fenrus.org/before.svghttp://www.fenrus.org/after.svg
Note the long time "agp_ali_init" takes in the first graph; my laptop
doesn't even have an ALI chip in it! (the bootgraphs look a bit
dissimilar, but that's the point, the first one has a bunch of arbitrary
delays in it that cause it to look very different)
This reduces my kernel boot time by about 20%
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If device_register() in device_create_vargs() fails, the device
must be cleaned up with put_device() (which is also fine on NULL)
instead of kfree().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the comments on how to use device_initialize(), device_add()
and device_register() a bit clearer - in particular, explicitly
note that put_device() must be used once we tried to add the device
to the hierarchy.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the following needlessly global functions static:
- ibft_attr_show_initiator()
- ibft_attr_show_nic()
- ibft_attr_show_target()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Konrad Rzeszutek <ketuzsezr@darnok.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global struct platform_pm_ops static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the Ethernet/RNDIS gadget driver builds: don't
use separate compilation, since it works poorly when key
parts are library code (with init sections etc). Instead
be as close as we can to "gcc --combine ...".
This is a bit more complicated than most of the others
because it had to resolve a few symbol collisions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the CDC Composite gadget driver builds: don't
use separate compilation, since it works poorly when key
parts are library code (with init sections etc). Instead
be as close as we can to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the file storage gadget driver builds: don't
use separate compilation, since it works poorly when key
parts are library code (with init sections etc). Instead
be as close as we can to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the printer gadget driver builds: don't use
separate compilation, since it works poorly when key parts
are library code (with init sections etc). Instead be as
close as we can to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the MIDI gadget driver builds: don't use separate
compilation, since it works poorly when key parts are library
code (with init sections etc). Instead be as close as we can
to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the Gadget Zero driver builds: don't use
separate compilation, since it works poorly when key
parts are library code (with init sections etc).
Instead be as close as we can to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the serial gadget driver builds: don't use
separate compilation, since it works poorly when key parts
are library code (with init sections etc). Instead be as
close as we can to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that device_create() has been audited, rename things back to the
original call to be sane.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that device_create() has been audited, rename things back to the
original call to be sane.
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that device_create() has been audited, rename things back to the
original call to be sane.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that device_create() has been audited, rename things back to the
original call to be sane.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that device_create() has been audited, rename things back to the
original call to be sane.
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that device_create() has been audited, rename things back to the
original call to be sane.
Cc: Ben Collins <ben.collins@ubuntu.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Straight forward conversions to CONFIG_MODULE; many drivers
include <linux/kmod.h> conditionally and then don't have any
other conditional code so remove it from those.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: video4linux-list@redhat.com
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-ppp@vger.kernel.org
Cc: dm-devel@redhat.com
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
For whatever value of 'OK' can be applied to the use of token ring. Seems
the 32bit to 64bit cleanups missed re-enabling the pcmcia driver
Closes#7133 and also reviewed the code in question
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Align ip header to a 16 byte boundary to avoid unaligned
access like other drivers.
Without this patch, xen-netfront doesn't work well on ia64.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Not sure anyone uses this driver any more, maybe we should just drop it ?
Code is still foul but at least a fraction less broken.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We cannot select INTEL_IOATDMA in Kconfig as soon as MYRI10GE or IXGBE
is enabled since the former is not available on all architectures.
Just use a Kconfig bool {IXGBE,MYRI10GE}_DCA set to =y when DCA
support can actually be built.
[myri10ge portion written and signed-off-by] Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
safe_delay_store() currently truncates the last character of input since
it tells strlcpy that the buffer can only hold 'len' characters, off by
one. sysfs already null terminates the buffer, so just increase the
last argument to strlcpy.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Reinitialize bridge registers after suspend, but avoid repeating the ioremap
Tested and works on AMD761
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of doing a posting read after each GTT entry update, do a single one
at the end of the writes. This should reduce boot time a tiny amount by
avoiding a lot of extra uncached reads.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On the GM45, the amount of stolen memory mapped to the GTT was underestimated,
even though we had 508KB more available since the GTT doesn't take from
stolen memory. On the non-GM45 G4X, we overestimated how much stolen was
mapped to the GTT by 4KB, resulting in GPU page faults when that page was
accessed.
This update requires a corresponding update to xf86-video-intel to work
correctly.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's a fault injection module, but I don't think we should oops here.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Update the help texts for the HID-quirk drivers, so that they are a little
bit more descriptive.
Also make some obsolete help descriptions up to date.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 9be7bbd54d
(HID: build drivers for all quirky devices by default)
made a wrong assumption about select/depends interaction in Kconfig,
resulting in possibility of link failure with certain configuration
options.
Fix this by explicitly having all the quirk-drivers depend on
USB_HID, default to y and make the possibility to alter the
settings dependent on EBMEDDED.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reported by Jay Fenlason: ioctl() did not return as intended
- the size of data read into ioctl_send_request,
- the number of datagrams enqueued by ioctl_queue_iso.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
queuecommand() looked at the remote and local node IDs before it read
the bus generation. The corresponding race with sbp2_reconnect updating
these data was probably impossible to happen though because the current
code blocks the SCSI layer during reconnection. However, better safe
than sorry, especially if someone later improves the code to not block
the SCSI layer.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
1. We don't need to round the SBP-2 segment size limit down to a
multiple of 4 kB (0xffff -> 0xf000). It is only necessary to
ensure quadlet alignment (0xffff -> 0xfffc).
2. Use dma_set_max_seg_size() to tell the DMA mapping infrastructure
and the block IO layer about the restriction. This way we can
remove the size checks and segment splitting in the queuecommand
path.
This assumes that no other code in the firewire stack uses
dma_map_sg() with conflicting requirements. It furthermore assumes
that the controller device's platform actually allows us to set the
segment size to our liking. Assert the latter with a BUG_ON().
3. Also use blk_queue_max_segment_size() to tell the block IO layer
about it. It cannot know it because our scsi_add_host() does not
point to the FireWire controller's device.
Thanks to Grant Grundler and FUJITA Tomonori for advice.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Share code between fw_send_request + wait_for_completion callers.
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Addendum:
Removes an unnecessary struct and an ununsed retry loop.
Calls it fw_run_transaction() instead of fw_send_request_sync().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@redhat.com>
There are situations when nodes vanish from the bus and come back in
quickly thereafter:
- When certain bus-powered hubs are plugged in,
- when certain disk enclosures are switched from self-power to bus
power or vice versa and break the daisy chain during the transition,
- when the user plugs a cable out and quickly plugs it back in, e.g.
to reorder a daisy chain (works on Mac OS X if done quickly enough),
- when certain hubs temporarily malfunction during high bus traffic.
The ieee1394 driver's nodemgr already contained a function to set
vanished nodes aside into "limbo"; i.e. they wouldn't actually be
deleted right away. (In fact, only unloading the driver or writing into
an obscure sysfs attribute would delete them eventually.) If nodes
reappeared later, they would be resurrected out of limbo.
Moving nodes into and out of limbo was accompanied with calling the
.suspend() and .resume() driver methods of the drivers which were bound
to a respective node's unit directories. Not only is this somewhat
strange due to the intended use of these driver methods for power
management, also the sbp2 driver in particular does not implement
.suspend() and .resume(). Hence sbp2 would be disconnected from devices
in situations as listed above.
We now:
- leave drivers bound when nodes go into limbo,
- call the drivers' .update() when nodes come out of limbo,
- automatically delete in-limbo nodes 3 seconds after the last
bus reset and bus rescan.
- Because of the automatic removal, the now obsolete bus attribute
/sys/bus/ieee1394/destroy_node is removed.
This especially lets sbp2 survive brief disconnections. You can for
example yank a disk's cable and plug it back in while reading the
respective disk with dd, but dd will happily continue as if nothing
happened.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Remove useless pointer type casts.
Remove unnecessary hi->host indirection where only host is used.
Remove an unnecessary WARN_ON.
Change a few names.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
init->channel and v.buffer are unsigned and tests for < 0 therefore
always false. gcc knows this and eliminates the code, but anyway...
Reported by Roel Kluin.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Application programs should use a libraw1394 handle only in a single
thread. The raw1394 driver was apparently relying on this, because it
did nothing to protect its fi->state variable from corruption due to
concurrent accesses.
We now serialize the fi->state accesses. This affects the write() path.
We re-use the state_mutex which was introduced to protect fi->iso_state
accesses in the ioctl() path. These paths and accesses are independent
of each other, hence separate mutexes could be used. But I don't see
much benefit in that.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Refactor the ioctl dispatcher in order to move a fraction of it out of
the section which is serialized by fi->state_mutex. This is not so much
about performance but more about self-documentation: The mutex_lock()/
mutex_unlock() calls are now closer to the data accesses which the mutex
protects, i.e. to the iso_state switch.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This removes the last usage of the Big Kernel Lock from the ieee1394
stack, i.e. from raw1394's (unlocked_)ioctl and compat_ioctl.
The ioctl()s don't need to take the BKL, but they need to be serialized
per struct file *. In particular, accesses to ->iso_state need to be
serial. We simply use a blocking mutex for this purpose because
libraw1394 does not use O_NONBLOCK. In practice, there is no lock
contention anyway because most if not all libraw1394 clients use a
libraw1394 handle only in a single thread.
mmap() also accesses ->iso_state. Until now this was unprotected
against concurrent changes by ioctls. Fix this bug while we are at it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
1. We don't need to round the SBP-2 segment size limit down to a
multiple of 4 kB (0xffff -> 0xf000). It is only necessary to
ensure quadlet alignment (0xffff -> 0xfffc).
2. Use dma_set_max_seg_size() to tell the DMA mapping infrastructure
and the block IO layer about the restriction. This way we can
remove the size checks and segment splitting in the queuecommand
path.
This assumes that no other code in the ieee1394 stack uses
dma_map_sg() with conflicting requirements. It furthermore assumes
that the controller device's platform actually allows us to set the
segment size to our liking. Assert the latter with a BUG_ON().
3. Also use blk_queue_max_segment_size() to tell the block IO layer
about it. It cannot know it because our scsi_add_host() does not
point to the FireWire controller's device.
We can also uniformly use dma_map_sg() for the single segment case just
like for the multi segment case, to further simplify the code.
Also clean up how the page table is converted to big endian.
Thanks to Grant Grundler and FUJITA Tomonori for advice.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Two dma_sync_single_for_cpu() were called in the wrong place.
Luckily they were merely for DMA_TO_DEVICE, hence nobody noticed.
Also reorder the matching dma_sync_single_for_device() a little bit
so that they reside in the same functions as their counterparts.
This also avoids syncing the s/g table for requests which don't use it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Kill unused <asm/debug.h> inclusions
MIPS: IP32: Add platform device for CMOS RTC; remove dead code
RTC: M48T35: new RTC driver
MIPS: IP27: Switch over to RTC class driver
MIPS: DS1286: New RTC driver
MIPS: IP22/28: Switch over to RTC class driver
MIPS: PCI: Scan busses when they are registered
MIPS: WGT634U: Add reset button support
MIPS: BCM47xx: Use the new SSB GPIO API
MIPS: BCM47xx: Remove references to BCM947XX
MIPS: WGT634U: Add machine detection message
MIPS: Align .data.cacheline_aligned based on CONFIG_MIPS_L1_CACHE_SHIFT
MIPS: show_cpuinfo prints the type of the calling CPU
MIPS: Fix wrong branch target in new spin_lock code.
MIPS: Have a heart for a lonely, lost header file ...
proc_clear_tty() gets called with interrupts off (while holding the task list
lock) from sys_setid. This means that it needs the _irqsave version of the
locking primitives.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The metronome driver produces warnings when built on x86-64 as it assumes that
size_t is an int. Use %Zd instead.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (158 commits)
powerpc: Fix CHRP PCI config access for indirect_pci
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
powerpc: Fix 32-bit SMP boot on CHRP
powerpc: Fix link errors on 32-bit machines using legacy DMA
powerpc/pci: Improve detection of unassigned bridge resources
hvc_console: Fix free_irq in spinlocked section
powerpc: Get USE_STRICT_MM_TYPECHECKS working again
powerpc: Reflect the used arguments in machine_init() prototype
powerpc: Fix DMA offset for non-coherent DMA
powerpc: fix fsl_upm nand driver modular build
powerpc/83xx: add NAND support for the MPC8360E-RDK boards
powerpc: FPGA support for GE Fanuc SBC610
i2c: MPC8349E-mITX Power Management and GPIO expander driver
powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree
powerpc: document the "fsl,ssi-dma-channel" compatible property
powerpc: disable CHRP and PMAC support in various defconfigs
OF: add fsl,mcu-mpc8349emitx to the exception list
powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
powerpc: remove support for bootmem-allocated memory for the DIU driver
powerpc: remove non-dependent load fsl_booke PTE_64BIT
...
This patch extends the VT-d driver to support KVM
[Ben: fixed memory pinning]
[avi: move dma_remapping.h as well]
Signed-off-by: Kay, Allen M <allen.m.kay@intel.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: Ben-Ami Yassour <benami@il.ibm.com>
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This driver replaces the broken ip27-rtc driver in drivers/char and
gives back RTC support for SGI IP27 machines.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This driver replaces the broken DS1286 driver in drivers/char and gives back
RTC support for SGI IP22 and IP28 machines.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Today's linux-next build (powerpc ppc64_defconfig) failed like this:
drivers/md/raid1.c: In function 'sync_request':
drivers/md/raid1.c:1759: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid1.o] Error 1
make[3]: *** Waiting for unfinished jobs....
drivers/md/raid10.c: In function 'sync_request':
drivers/md/raid10.c:1749: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid10.o] Error 1
drivers/md/md.c: In function 'md_do_sync':
drivers/md/md.c:5915: error: implicit declaration of function 'msleep'
Caused by commit 6caa3b0bbdb474647f6bdd8a958ffc46f78d8d58 ("md: Remove
unnecessary #includes, #defines, and function declarations"). I added
the following patch.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NeilBrown <neilb@suse.de>
The hw_key pointer is used (and obviously NULL) after skb->cb is
memset to 0. This patch grabs the iv_len before the memset call.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Belkin F5D7050rev5000de (id 050d:705e) has the Realtek RTL8187B chip
and works with the 2.6.27 driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates p54usb's device list.
It adds the ID for SMC 2862W-G v2 and marks the
"Spinnaker Proto board" as a first generation device.
Reported-by: <jafg666@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As I've reported, ath9k currently fails utterly when fragmentation
is enabled. This makes ath9k "support" hardware fragmentation by
not supporting fragmentation at all to avoid the double-free issue.
The patch also changes mac80211 to report errors from the driver
operation to userspace.
That hack in ath9k should be removed once the rate control algorithm
it has is fixed, and we can at that time consider removing the hw
fragmentation support entirely since it's not used by any driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Below patch removes the following warning during compilation.
drivers/net/wireless/libertas/cmd.c:826: warning: unused variable 'old_channel'
Signed-off-by : Manish Katiyar <mkatiyar@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A similar problem was highlighted in the orinoco_cs driver by lockdep.
This patch fixes the spectrum_cs driver.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes ct kill configuration for 5350. Temperature units that
HW expects are in Celsius not in kelvins.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit entitled "p54: Fix sparse warnings" introduced a compile
error on PPC architecture. Thanks to Johannes Berg
<johannes@sipsolutions.net> for reporting this problem.
Signed-off-by: <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When CONFIG_IWLWIFI_DEBUG is not set and CONFIG_IWLWIFI is set,
we get this compilation warning:
/wireless-next-2.6/drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In
function 'rs_free_sta':
/wireless-next-2.6/drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2425:
warning: unused variable 'priv'
This patch fixes it by adding __maybe_unused attribute.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-viapro: Add support for SMBus Process Call transactions
i2c: Restore i2c_smbus_process_call function
i2c: Do earlier driver model init
i2c: Only build Tyan SMBus mux drivers on x86
i2c: Guard against oopses from bad init sequences
i2c: Document the implementation details of the /dev interface
i2c: Improve dev-interface documentation
i2c-parport-light: Don't register a platform device resource
hwmon: (dme1737) Convert to a new-style i2c driver
hwmon: (dme1737) Be less i2c-centric
i2c/tps65010: Vibrator hookup to gpiolib
i2c-viapro: Add VX800/VX820 support
i2c: Renesas Highlander FPGA SMBus support
i2c-pca-isa: Don't grab arbitrary resources
i2c/isp1301_omap: Convert to a new-style i2c driver, part 2
i2c/isp1301_omap: Convert to a new-style i2c driver, part 1
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (55 commits)
HID: build drivers for all quirky devices by default
HID: add missing blacklist entry for Apple ATV ircontrol
HID: add support for Bright ABNT2 brazilian device
HID: Don't let Avermedia Radio FM800 be handled by usb hid drivers
HID: fix numlock led on Dell device 0x413c/0x2105
HID: remove warn() macro from usb hid drivers
HID: remove info() macro from usb HID drivers
HID: add appletv IR receiver quirk
HID: fix a lockup regression when using force feedback on a PID device
HID: hiddev.h: Fix example code.
HID: hiddev.h: Fix mixed space and tabs in example code.
HID: convert to dev_* prints
HID: remove hid-ff
HID: move zeroplus FF processing
HID: move thrustmaster FF processing
HID: move pantherlord FF processing
HID: fix incorrent length condition in hidraw_write()
HID: fix tty<->hid deadlock
HID: ignore iBuddy devices
HID: report descriptor fix for remaining MacBook JIS keyboards
...
We shouldn't rely on "pnp_platform_devices" to tell us whether there
is a PNP RTC device.
I introduced "pnp_platform_devices", but I think it was a mistake.
All it tells us is whether we found any PNPBIOS or PNPACPI devices.
Many machines have some PNP devices, but do not describe the RTC
via PNP. On those machines, we need to do the platform driver probe
to find the RTC.
We should just register the PNP driver and see whether it claims anything.
If we don't find a PNP RTC, fall back to the platform driver probe.
This (in conjunction with the arch/x86/kernel/rtc.c patch to add
a platform RTC device when PNP doesn't have one) should resolve
these issues:
http://bugzilla.kernel.org/show_bug.cgi?id=11580https://bugzilla.redhat.com/show_bug.cgi?id=451188
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Reported-by: Rik Theys <rik.theys@esat.kuleuven.be>
Reported-by: shr_msn@yahoo.com.tw
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 611e097d77
Author: Christian Borntraeger <borntraeger@de.ibm.com>
hvc_console: rework setup to replace irq functions with callbacks
introduced a spinlock recursion problem. The notifier_del is
called with a lock held, and in turns calls free_irq which then
complains when manipulating procfs. This fixes it by moving the
call to the notifier to outside of the locked section.
Signed-off-by: Christian Borntraeger<borntraeger@de.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move rtc_wake_setup() from drivers/acpi/glue.c into the RTC driver
in drivers/rtc/rtc-cmos.c.
This removes the ordering constraint between the module_init(acpi_rtc_init)
and the cmos_do_probe() code that depends on it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Once kernel configuration has CONFIG_HID turned on, let also all the
specialized drivers for quirky devices to be built (unless CONFIG_EMBEDDED is
specified), as usually users don't care that much which driver
gives them the functionality, but when they want generic support, they
probably want to have support for all the quirky devices as well.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device is already handled by hid-apple driver, but the blacklist entry
was missing in generic driver.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This keyboard needs to reset the LEDS during probe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on an original patch from Alexey Klimov <klimov.linux@gmail.com>,
against kernel version 2.6.27.
This device is already handled by radio-mr800 driver, and we therefore
want usbhid not to touch it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 8006479c9b introduced a spinlock in
input_dev->event_lock, which is locked when handling input events.
However, the hid-pidff driver sleeps when handling events as it waits for
reports being sent to the device before changing the report contents
again.
This causes a system lockup when trying to use force feedback with a PID
device, a regression introduced in 2.6.24 and 2.6.23.15.
Fix it by extracting the raw report data from struct hid_report
immediately when hid_submit_report() is called, therefore allowing
drivers to change the contents of struct hid_report immediately without
affecting the already-queued transfer.
In hid-pidff, re-add the removed usbhid_wait_io() to
pidff_erase_effect() instead, to prevent a full report queue from causing
the submission to fail, thus not freeing up device memory.
pidff_erase_effect() is not called while dev->event_lock is held.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since we have a real device bound to a driver, we may use struct
device for printing. Use dev_* functions instead of printks in
4 drivers.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid-ff.c now calls only pidff (generic driver), the special ones are now
in separate drivers. Invoke pidff on all non-special directly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move the force feedback processing into a separate module.
[jkosina@suse.cz: fix Kconfig texts a little bit]
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The bound check on the buffer length
if (count > HID_MIN_BUFFER_SIZE)
is of course incorrent, the proper check is
if (count > HID_MAX_BUFFER_SIZE)
Fix it.
Reported-by: Jerry Ryle <jerry@mindtribe.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_compat_load() runs on the default workqueue, it request_module(), it
execs modprobe, it exits, tty flushes default workqueue, it hangs, because
we are still in it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: <Valdis.Kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
iBuddy devices claim to be HID devices, but they are not.
Add them to the blacklist.
Signed-off-by: Remi Cattiau <remi@cattiau.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes a problem that MacBook JIS keyboard sends wrong report
descriptors. Although it has already been fixed in the first Core 2 Duo model,
it still remains in other models of MacBook.
Signed-off-by: Tomoya Adachi <adachi@il.is.s.u-tokyo.ac.jp>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current kernel has no support for autocentering for Logitech wheels. By
default autocentering enabled in wheel and constant effect does not work
properly. Using USB sniffer I found command which change autocentering
settings: 0xFE, 0x0D, 0x0R, 0x0L, 0x80, 0x00, 0x00, where R - clockwise force,
L - counter-clockwise (0x0-0xF, 0xC = 100%).
Signed-off-by: Sergey Belyashov <Sergey.Belyashov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Kconfig option for HID_COMPAT should read "lose", not "loose".
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This seems to be the very same device, as already supported Smartjoy
dual Plus, but with slightly different vendor ID. Let's support this
one too.
Reported-by: David Ashley <dashxdr@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch reverts the change made four years ago here:
http://www.vg.kernel.org/pub/linux/kernel/people/gregkh/usb/2.4/usb-hid-2.4.25-pre7.patch
UPS's made by MGE can be used with usbhid just fine, and by removing the
ignore quirk allows them to be used with HAL so they just work when plugged
in, without needing to be manually configured.
With the ignore quirk in place a user would have to configure NUT before the
UPS could be used, as NUT uses it's own internal USB matching framework
to match against the USB devices, do low level control messages on the
device and then parse the HID tables all in userspace.
This is not needed, as allowing the device to be claimed as a usbhid device
allows it to be used like any other USB UPS device. The devices correctly
advertise the power device page which can be queried for the device state.
I assume the quirk was changed so that people using < libusb 0.1.8 could
still use NUT's internal HID code to manage the UPS.
libusb 0.1.8 was released quite some time ago: 2004-02-11.
This patch does not break NUT as in drivers/libusb.c the device is force
unbound from the kernel driver using usb_detach_kernel_driver_np () where
it can be controlled like normal.
[jkosina@suse.cz: adapt to the new hidbus code]
Signed-off-by: Richard Hughes <rhughes@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Introduce a list of devices for which there is need to
force a creation of the hiddev interface, but still they
are operated by generic driver (i.e. certain UPS).
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge the logitech force feedback processing directly into logitech
driver from the usbhid core.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move the handling of the leds resetting from the core to
the dell and logitech drivers.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move connecting from usbhid to the hid layer and fix also hidp in
that manner.
This removes all the ignore/force hidinput/hiddev connecting quirks.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove support for both dynamic and static report descriptor
quirks. There is no longer rdesc code which it would support,
so it's useless.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
