When operating the at803x in SGMII mode, resuming the chip
from power down brings up the copper-side link but leaves
the SGMII link in unconnected state (tested with at8031
attached to gianfar). In effect, this caused a permanent
link loss once the related interface was put down.
This patch ensures that power down handling in supspend()
and resume() is also applied to the SGMII link.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bulk free of SKBs happen transparently by the API call napi_consume_skb().
The napi budget parameter is needed by napi_consume_skb() to detect
if called from netpoll.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bulk free of SKBs happen transparently by the API call napi_consume_skb().
The napi budget parameter is usually needed by napi_consume_skb()
to detect if called from netpoll. In this patch it has an extra meaning.
For mlx4 driver, the mlx4_en_stop_port() call is done outside
NAPI/softirq context, and cleanup the entire TX ring via
mlx4_en_free_tx_buf(). The code mlx4_en_free_tx_desc() for
freeing SKBs are shared with NAPI calls.
To handle this shared use the zero budget indication is reused,
and handled appropriately in napi_consume_skb(). To reflect this,
variable is called napi_mode for the function call that needed
this distinction.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For pcie nic, after setting link speed and there is no link driver does not need
to do phy reset until link up.
For some pcie nics, to do this will also reset phy speed down counter and prevent
phy from auto speed down.
This patch fix the issue reported in following link.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1547151
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware now tells us that the reset is done by passing a magic value
via register. Use it to shorten the wait in case this is supported.
With old firmware, we still wait until the timeout is reached.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On AT91 SoCs, the User Register (USRIO) exposes a switch to configure the
"Reduced" or "Traditional" version of the Media Independent Interface
(RMII vs. MII or RGMII vs. GMII).
As on the older EMAC version, on GMAC, this switch is set by default to the
non-reduced type of interface, so use the existing capability and extend it to
GMII as well. We then keep the current logic in the macb_init() function.
The capabilities of sama5d2, sama5d4 and sama5d3 GEM interface are updated in
the macb_config structure to be able to properly enable them with a traditional
interface (GMII or MII).
Reported-by: Romain HENRIET <romain.henriet@l-acoustics.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the "prepare for reconnect" pr_info in xenbus.c. It's largely
uninteresting and the states of the frontend and backend can easily be
observed by watching the (o)xenstored log.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code does not currently support a frontend passing multiple extra info
fragments to the backend in a tx request. The xenvif_get_extras() function
handles multiple extra_info fragments but make_tx_response() assumes there
is only ever a single extra info fragment.
This patch modifies xenvif_get_extras() to pass back a count of extra
info fragments, which is then passed to make_tx_response() (after
possibly being stashed in pending_tx_info for deferred responses).
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
ath10k
* dt: add bindings for ipq4019 wifi block
* start adding support for qca4019 chip
ath9k
* add device ID for Toshiba WLM-20U2/GN-1080
* allow more than one interface on DFS channels
bcma
* move flash detection code to ChipCommon core driver
brcmfmac
* IPv6 Neighbor discovery offload
* driver settings that can be populated from different sources
* country code setting in firmware
* length checks to validate firmware events
* new way to determine device memory size needed for BCM4366
* various offloads during Wake on Wireless LAN (WoWLAN)
* full Management Frame Protection (MFP) support
iwlwifi
* add support for thermal device / cooling device
* improvements in scheduled scan without profiles
* new firmware support (-21.ucode)
* add MSIX support for 9000 devices
* enable MU-MIMO and take care of firmware restart
* add support for large SKBs in mvm to reach A-MSDU
* add support for filtering frames from a BA session
* start implementing the new Rx path for 9000 devices
* enable the new Radio Resource Management (RRM) nl80211 feature flag
* add a new module paramater to disable VHT
* build infrastructure for Dynamic Queue Allocation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJW4HwrAAoJEG4XJFUm622bvFUH/ArZD53Jh8btu8ukmkgKOPkc
hCnvR639TURCNkC/e1lR0MFjO1QLLZ2m1tdRoZQfLiZm63HUuQzPDmaVnTeVfjrI
4p3LmYriTECvgLoqVJgmBjNWiC61fMbWTJ91YqQiw2ZhvuKbcsu6oz/jU9MyCLyJ
7WSk+HUqAnwtj7z515vAYQYapdUbxU1u7m/NgYdiYKTXfBR2ozUbfDR18Ey2EBWC
KkDpFXyxo7ZByXzVA1B1UogB9NteV7IV1+WHphIX/XGdVQPpwRV3KxmLqKjIWW5E
1Cv3q05vWapev9V5ZYghLpAGUQTu8h0nH2v0bJa9nSiQX23/Vkz7xxA/hi5gBOo=
=aqji
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-03-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.6
Major changes:
ath10k
* dt: add bindings for ipq4019 wifi block
* start adding support for qca4019 chip
ath9k
* add device ID for Toshiba WLM-20U2/GN-1080
* allow more than one interface on DFS channels
bcma
* move flash detection code to ChipCommon core driver
brcmfmac
* IPv6 Neighbor discovery offload
* driver settings that can be populated from different sources
* country code setting in firmware
* length checks to validate firmware events
* new way to determine device memory size needed for BCM4366
* various offloads during Wake on Wireless LAN (WoWLAN)
* full Management Frame Protection (MFP) support
iwlwifi
* add support for thermal device / cooling device
* improvements in scheduled scan without profiles
* new firmware support (-21.ucode)
* add MSIX support for 9000 devices
* enable MU-MIMO and take care of firmware restart
* add support for large SKBs in mvm to reach A-MSDU
* add support for filtering frames from a BA session
* start implementing the new Rx path for 9000 devices
* enable the new Radio Resource Management (RRM) nl80211 feature flag
* add a new module paramater to disable VHT
* build infrastructure for Dynamic Queue Allocation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the GRO handlers for GRE, VXLAN, GENEVE, and FOU so that
we do not clear the flush bit until after we have called the next level GRO
handler. Previously this was being cleared before parsing through the list
of frames, however this resulted in several paths where either the bit
needed to be reset but wasn't as in the case of FOU, or cases where it was
being set as in GENEVE. By just deferring the clearing of the bit until
after the next level protocol has been parsed we can avoid any unnecessary
bit twiddling and avoid bugs.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is OF-DPA specific, used only there, similar to
ofdpa_port->ageing_time. So move it to OF-DPA code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the scenario where slowpath configuration isn't passing due to
various pause configurations affecting the chip, the theoretical time
required in worst-case-scenario to empty hw fifos sufficiently to
guarantee that slowpath configuration would flow is currently
insufficient.
This increases such a drain request to the theoretical maximum.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle a new message from the MFW, one that indicate that the transciever
state has changed, and log that into the system logs.
Signed-off-by: Zvi Nachmani <Zvi.Nachmani@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver interaction with the managemnt firmware is done via mailbox
commands which the management firmware periodically sample, as well
as placing of additional data in set places in the shared memory.
Each PF has a single designated mailbox address, and all flows that
require messaging to the management should use it.
This patch does 2 things:
1. It re-defines the critical section surrounding the mailbox sending -
that section should include the setting of the shared memory as well as
the sending of the command [otherwise a race might send a command with
the data of a different command].
2. It moves the locking scheme from using mutices into using spinlocks.
This lays the groundwork for sending MFW commands from non-sleepable
contexts.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is configured for Multi-function mode, some older management
firmware might incorrectly notify interfaces of link changes while they
haven't requested the physical link configuration to be set.
This can create bizzare race conditions where unloading interfaces are
getting notified that the link is up.
Let the driver compensate - store the logical requested state of the link
and don't propagate notifications after protocol driver explicitly
requires the link to be unset.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds support for setting the IPv6 flow label for geneve per
device and through collect metadata (ip_tunnel_key) frontends. Also here,
the geneve dst cache does not need any special considerations, for the
cases where caches can be used, the label is static per cache.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds support for setting the IPv6 flow label for vxlan per
device and through collect metadata (ip_tunnel_key) frontends. The
vxlan dst cache does not need any special considerations here, for
the cases where caches can be used, the label is static per cache.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends udp_tunnel6_xmit_skb() to pass in the IPv6 flow label
from call sites. Currently, there's no such option and it's always set to
zero when writing ip6_flow_hdr(). Add a label member to ip_tunnel_key, so
that flow-based tunnels via collect metadata frontends can make use of it.
vxlan and geneve will be converted to add flow label support separately.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't hide varibles used by the logging macros.
Miscellanea:
o Use the more common ##__VA_ARGS__ extension
o Add missing newlines to formats
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rocker, ageing time is a per-port attribute, so the next time the FDB
cleanup timer fires should be set according to the lowest ageing time.
This will later allow us to delete the BR_MIN_AGEING_TIME macro, which was
added to guarantee minimum ageing time in the bridge layer, thereby breaking
existing behavior.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c62987bbd8 ("bridge: push bridge setting ageing_time down to
switchdev") added a check for minimum and maximum ageing time, but this
breaks existing behaviour where one can set ageing time to 0 for a
non-learning bridge.
Push this check down to the driver and allow the check in the bridge
layer to be removed. Currently ageing time 0 is refused by the driver,
but we can later add support for this functionality.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stack expects link layer headers in the skb linear section.
Macvtap can create skbs with llheader in frags in edge cases:
when (IFF_VNET_HDR is off or vnet_hdr.hdr_len < ETH_HLEN) and
prepad + len > PAGE_SIZE and vnet_hdr.flags has no or bad csum.
Add checks to ensure linear is always at least ETH_HLEN.
At this point, len is already ensured to be >= ETH_HLEN.
For backwards compatiblity, rounds up short vnet_hdr.hdr_len.
This differs from tap and packet, which return an error.
Fixes b9fb9ee07e ("macvtap: add GSO/csum offload support")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce offloading of skbedit mark action.
For example, to mark with 0x1234, all TCP (ip_proto 6) packets arriving
to interface ens9:
# tc qdisc add dev ens9 ingress
# tc filter add dev ens9 protocol ip parent ffff: \
flower ip_proto 6 \
indev ens9 \
action skbedit mark 0x1234
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parse tc_cls_flower_offload into device specific commands and program
the hardware to classify and act accordingly.
For example, to drop ICMP (ip_proto 1) packets from specific smac, dmac,
src_ip, src_ip, arriving to interface ens9:
# tc qdisc add dev ens9 ingress
# tc filter add dev ens9 protocol ip parent ffff: \
flower ip_proto 1 \
dst_mac 7c:fe:90:69:81:62 src_mac 7c:fe:90:69:81:56 \
dst_ip 11.11.11.11 src_ip 11.11.11.12 indev ens9 \
action drop
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend ndo_setup_tc() to support ingress tc offloading. Will be used by
later patches to offload tc flower filter.
Feature is off by default and could be enabled by issuing:
# ethtool -K eth0 hw-tc-offload on
Offloads flow table is dynamically created when first filter is
added.
Rules are saved in a hash table that is maintained by the consumer (for
example - the flower offload in the next patch).
When last filter is removed and no filters exist in the hash table, the
offload flow table is destroyed.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the vlan and main flow tables to use priority 1. This will allow
the upcoming TC offload logic to use a higher priority (0) for the
offload steering table.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restricting handle to TC_H_ROOT breaks the old instantiation of mqprio
to setup a hardware qdisc. This patch relaxes the test, to only check the
type.
Fixes: 08fb1da ("net/mlx5e: Support DCBNL IEEE ETS")
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to handle flow table entry destinations only if the action
associated with the rule is forwarding (MLX5_FLOW_CONTEXT_ACTION_FWD_DEST).
Fixes: 26a8145390 ('net/mlx5_core: Introduce flow steering firmware commands')
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Makefile and Kconfig required to make the driver build.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethernet support for MediaTek SoCs from the MT7623 family. These have
dual GMAC. Depending on the exact version, there might be a built-in
Gigabit switch (MT7530). The core does not have the typical DMA ring setup.
Instead there is a linked list that we add descriptors to. There is only
one linked list that both MACs use together. There is a special field
inside the TX descriptors called the VQID. This allows us to assign packets
to different internal queues. By using a separate id for each MAC we are
able to get deterministic results for BQL. Additionally we need to
provide the core with a block of scratch memory that is the same size as
the RX ring and data buffer. This is really needed to make the HW datapath
work. Although the driver does not support this yet, we still need to
assign the memory and tell the core about it for RX to work.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
'commit 55482edc25
("qede: Add slowpath/fastpath support and enable hardware GRO")'
introduces below error when compiling net-next with "make ARCH=x86_64"
drivers/built-in.o: In function `qede_rx_int':
qede_main.c:(.text+0x6101a0): undefined reference to `tcp_gro_complete'
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o While the driver is in the middle of a MB completion processing
and it receives a spurious MB interrupt, it is mistaken as a good MB
completion interrupt leading to premature completion of the next MB
request. Fix the driver to guard against this by checking the current
state of MB processing and ignore the spurious interrupt.
Also added a stats counter to record this condition.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o atomic_t usage is incorrect as we are not implementing
any atomicity.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Queue Set Configuration code was always reserving room for a
Forwarded interrupt Queue even in the cases where we weren't using it.
Figure out how many Ports and Queue Sets we can support. This depends on
knowing our Virtual Function Resources and may be called a second time
if we fall back from MSI-X to MSI Interrupt Mode. This change fixes that
problem.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids a race condition where a system that has network devices set up
to be automatically configured and we get the first Port Link Status
message from the firmware on the Asynchronous Firmware Event Queue before
we've enabled interrupts. If that happens, we end up losing the interrupt
and never realizing that the links has actually come up.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to change the 802.1Q port mode for the same value.
Thus avoid such message:
[ 401.954836] dsa dsa@0 lan0: 802.1Q Mode: Disabled (was Disabled)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port register 0x07 contains more options than just the default VID,
even though they are not used yet. So prefer a read then write operation
over a direct write.
This also allows to keep track of the change through dynamic debug.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply a few non-functional changes on the port state setter:
* add a dynamic debug message with state names to track changes
* explicit states checking instead of assuming their numeric values
* lock mutex only once when changing several port states
* use bitmap macros to declare and access port_state_update_mask
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iff dma_map_single() fails, 'rxdesc' should point to the last filled RX
descriptor, so that it can be marked as the last one, however the driver
would have already advanced it by that time. In order to fix that, only
fill an RX descriptor once all the data for it is ready.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a low memory situation, if netdev_alloc_skb() fails on a first RX ring
loop iteration in sh_eth_ring_format(), 'rxdesc' is still NULL. Avoid
kernel oops by adding the 'rxdesc' check after the loop.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of CAN2.0 EFF frame, the controller handles frame IDs in a
rather bizzare way. The ID is split into an extended part, IDX[28:11]
and standard part, ID[10:0]. In the TX path, the core first sends the
top 11 bits of the IDX, followed by ID and finally the rest of IDX.
In the RX path, the core stores the ID the LSbit part of IDX field,
followed by the LSbit parts of real IDX. The MSbit parts of IDX are
stored in ID field of the register.
This patch implements the necessary bit shuffling to mitigate this
obscure behavior. In case two of these controllers are connected
together, the RX and TX bit swapping nullifies itself and the issue
does not manifest. The issue only manifests when talking to another
different CAN controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The RX and TX ID mask for CAN2.0 is 11 bits wide. This patch fixes
the incorrect mask, which caused the CAN IDs to miss the MSBit both
on receive and transmit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The TX DLC, the transmission length information, was not written
into the transmit configuration register. When using the CAN core
with different CAN controller, the receiving CAN controller will
receive only the ID part of the CAN frame, but no data at all.
This patch adds the TX DLC into the register to fix this issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The clock generation does not match reality when using the CAN IP
core outside of the FPGA design. This patch fixes the computation
of values which are programmed into the clock generator registers.
First, there are some off-by-one errors which manifest themselves
only when communicating with different controller, so those are
fixed.
Second, the bits in the clock generator registers have different
meaning depending on whether the core is in ISO CANFD mode or any
of the other modes (BOSCH CANFD or CAN2.0). Detect the ISO CANFD
mode and fix handling of this special case of clock configuration.
Finally, the CAN clock speed is in CANCLOCK register, not SYSCLOCK
register, so fix this as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add pci_error_handler callbacks to support for pcie advanced error
recovery.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the more useful port statistics in ethtool -S for the PF device.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include some of the port error counters (e.g. crc) in ->ndo_get_stats64()
for the PF device.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
