The Goodix GT9286 is a capacitive touch sensor IC based on GT1x.
This chip can be found on a number of smartphones, including the
F(x)tec Pro 1 and the Elephone U.
This has been tested on F(x)Tec Pro1 (MSM8998).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210109135512.149032-2-angelogioacchino.delregno@somainline.org
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ILI251x seems to report pressure information in the 5th byte of
each per-finger touch data element. On the available hardware, this
information has the values ranging from 0x0 to 0xa, which is also
matching the downstream example code. Report pressure information
on the ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201224071238.160098-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the st1232 datasheet, the host has to wait for the device
to change into Normal state before accessing registers other than the
Status Register.
If the reset GPIO is wired, the device is powered on during driver
probe, just before reading the resolution. However, the latter may
happen before the device is ready, leading to a probe failure:
st1232-ts 1-0055: Failed to read resolution: -6
Fix this by waiting until the device is ready, by trying to read the
Status Register until it indicates so, or until timeout.
On Armadillo 800 EVA, typically the first read fails with an I2C
transfer error, while the second read indicates the device is ready.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-4-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
st1232_ts_read_data() already reads ts->read_buf_len bytes (8 or 20
bytes) from the touchscreen controller. This was fine when it was used
to read touch point coordinates only, but is overkill for reading the
touchscreen resolution, which just needs 3 bytes.
Optimize transfers by passing the wanted number of bytes.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-3-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before, the maximum coordinates were fixed to (799, 479) or (319, 479),
depending on touchscreen controller type. The driver was changed to
read the actual values from the touchscreen controller, but did not take
into account the returned values are not the maximum coordinates, but
the touchscreen resolution (e.g. 800 and 480).
Fix this by subtracting 1.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-2-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- support for inhibiting input devices at request from userspace. If a
device implements open/close methods, it can also put device into low
power state. This is needed, for example, to disable keyboard and
touchpad on convertibles when they are transitioned into tablet mode
- now that ordinary input devices can be configured for polling mode,
dedicated input polling device implementation has been removed
- GTCO tablet driver has been removed, as it used problematic custom
HID parser, devices are EOL, and there is no interest from the
manufacturer
- a new driver for Dialog DA7280 haptic chips has been introduced
- a new driver for power button on Dell Wyse 3020
- support for eKTF2132 in ektf2127 driver
- support for SC2721 and SC2730 in sc27xx-vibra driver
- enhancements for Atmel touchscreens, AD7846 touchscreens, Elan
touchpads, ADP5589, ST1232 touchscreen, TM2 touchkey drivers
- fixes and cleanups to allow clean builds with W=1
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (86 commits)
Input: da7280 - fix spelling mistake "sequemce" -> "sequence"
Input: cyapa_gen6 - fix out-of-bounds stack access
Input: sc27xx - add support for sc2730 and sc2721
dt-bindings: input: Add compatible string for SC2721 and SC2730
dt-bindings: input: Convert sc27xx-vibra.txt to json-schema
Input: stmpe - add axis inversion and swapping capability
Input: adp5589-keys - do not explicitly control IRQ for wakeup
Input: adp5589-keys - do not unconditionally configure as wakeup source
Input: ipx4xx-beeper - convert comma to semicolon
Input: parkbd - convert comma to semicolon
Input: new da7280 haptic driver
dt-bindings: input: Add document bindings for DA7280
MAINTAINERS: da7280 updates to the Dialog Semiconductor search terms
Input: elantech - fix protocol errors for some trackpoints in SMBus mode
Input: elan_i2c - add new trackpoint report type 0x5F
Input: elants - document some registers and values
Input: atmel_mxt_ts - simplify the return expression of mxt_send_bootloader_cmd()
Input: imx_keypad - add COMPILE_TEST support
Input: applespi - use new structure for SPI transfer delays
Input: synaptics-rmi4 - use new structure for SPI transfer delays
...
The big change this release has been some excellent work from Lukas
Wunner which closes a bunch of holes in the cleanup paths for drivers,
mainly introduced as a result of devm conversions causing bad
interactions with the support SPI has for allocating the bus and driver
data together. Together with some of the other work done it feels like
we've turned the corner on several long standing pain points with the
API.
- Many cleanups around probe/remove and error handling from Lukas
Wunner and Uwe Kleine-König, and further fixes around PM from Zhang
Qilong.
- Provide a mask for which bits of the mode can safely be configured by
drivers and use that to fix an issue with the ADS7846 driver.
- Documentation of the expected interactions between SPI and GPIO level
chip select polarity configuration from H. Nikolaus Schaller,
hopefully we're pretty much at the end of sorting out the
interactions there. Thanks to Nikolaus, Sven Van Asbroeck and Linus
Walleij for this.
- DMA support for Allwinner sun6i controllers.
- Support for Canaan K210 Designware implementations and Intel Adler Lake.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl/Xeg4ACgkQJNaLcl1U
h9BbXQf8DwmtP/biVsB0yxag11Ac9xxDL2OdMXia/DBQZsVSxqGld4l7Bwl8CMVi
TISCmzO1f53l3KZK5wu1C5mV8tXgCu4zrsPErEsrK2V2+s+4lWy10MOfAHqq/lBR
L2kifZ/uoeMBaPvJqpRimM8tv2uPXPHOKsdy2G82LzMdk0OhE5p9IkL5Nc5JbKOl
X1iWTAxtUsDb8+B57AwHSMnL4R3pb/01N0PguJJ8DGol7Oj6VcDf7nh/tqvVkEot
Ku731oCBQwBhkZKOqd7mvQAjPyoJiFPI8nofC4Bj+a1BDlr+pRcILQ4469zaIAWT
nPV6BoHTu/tVV63j8YhuamjWYAsS0g==
=ezV7
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The big change this release has been some excellent work from Lukas
Wunner which closes a bunch of holes in the cleanup paths for drivers,
mainly introduced as a result of devm conversions causing bad
interactions with the support SPI has for allocating the bus and
driver data together.
Together with some of the other work done it feels like we've turned
the corner on several long standing pain points with the API.
Summary:
- Many cleanups around probe/remove and error handling from Lukas
Wunner and Uwe Kleine-König, and further fixes around PM from Zhang
Qilong.
- Provide a mask for which bits of the mode can safely be configured
by drivers and use that to fix an issue with the ADS7846 driver.
- Documentation of the expected interactions between SPI and GPIO
level chip select polarity configuration from H. Nikolaus Schaller,
hopefully we're pretty much at the end of sorting out the
interactions there. Thanks to Nikolaus, Sven Van Asbroeck and Linus
Walleij for this.
- DMA support for Allwinner sun6i controllers.
- Support for Canaan K210 Designware implementations and Intel Adler
Lake"
* tag 'spi-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (69 commits)
spi: dt-bindings: clarify CS behavior for spi-cs-high and gpio descriptors
spi: Limit the spi device max speed to controller's max speed
spi: spi-geni-qcom: Use the new method of gpio CS control
platform/chrome: cros_ec_spi: Drop bits_per_word assignment
platform/chrome: cros_ec_spi: Don't overwrite spi::mode
spi: dw: Add support for the Canaan K210 SoC SPI
spi: dw: Add support for 32-bits max xfer size
dt-bindings: spi: dw-apb-ssi: Add Canaan K210 SPI controller
spi: Update DT binding docs to support SiFive FU740 SoC
spi: atmel-quadspi: Fix use-after-free on unbind
spi: npcm-fiu: Disable clock in probe error path
spi: ar934x: Don't leak SPI master in probe error path
spi: mt7621: Don't leak SPI master in probe error path
spi: mt7621: Disable clock in probe error path
media: netup_unidvb: Don't leak SPI master in probe error path
spi: sc18is602: Don't leak SPI master in probe error path
spi: rb4xx: Don't leak SPI master in probe error path
spi: gpio: Don't leak SPI master in probe error path
spi: spi-mtk-nor: Don't leak SPI master in probe error path
spi: mxic: Don't leak SPI master in probe error path
...
Pull input fixes from Dmitry Torokhov:
- a fix for cm109 stomping on its own control URB if it tries to toggle
buzzer immediately after userspace opens input device (found by
syzcaller)
- another fix for Raydium touchscreens that do not like splitting
command transfers
- quirks for i8042, soc_button_array, and goodix drivers to make them
work better with certain hardware.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: goodix - add upside-down quirk for Teclast X98 Pro tablet
Input: cm109 - do not stomp on control URB
Input: i8042 - add Acer laptops to the i8042 reset list
Input: cros_ec_keyb - send 'scancodes' in addition to key events
Input: soc_button_array - add Lenovo Yoga Tablet2 1051L to the dmi_use_low_level_irq list
Input: raydium_ts_i2c - do not split tx transactions
Make use of generic touchscreen_properties structure to add axis
inversion and swapping capabilities. It's configurable via devicetree
properties:
touchscreen-inverted-x
touchscreen-inverted-y
touchscreen-swapped-x-y
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Link: https://lore.kernel.org/r/20200922093903.157232-1-s.riedmueller@phytec.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen on the Teclast x98 Pro is also mounted upside-down in
relation to the display orientation.
Signed-off-by: Simon Beginn <linux@simonmicro.de>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20201117004253.27A5A27EFD@localhost
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200228104508.15564-1-sergiu.cuciurean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of special-casing retrieval of number of X/Y electrodes based on
the firmware, let's select default values and mark registers as
non-existent on firmwares that do not support this operation.
Also mark "report rate" register as non-existent for generic firmwares
as having it set to 0 does not make sense.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Simon Budig <simon.budig@kernelconcepts.de>
Link: https://lore.kernel.org/r/X9FZFs3NZADoIhhH@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Collected patches from the two series below and associated tags so they
can be merged in one pile through the spi tree. Merry December!
SPI: https://lore.kernel.org/r/20201202214935.1114381-1-swboyd@chromium.org
cros-ec: https://lore.kernel.org/r/20201203011649.1405292-1-swboyd@chromium.org
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Gwendal Grignou <gwendal@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Alexandru M Stan <amstan@chromium.org>
Stephen Boyd (3):
platform/chrome: cros_ec_spi: Don't overwrite spi::mode
platform/chrome: cros_ec_spi: Drop bits_per_word assignment
spi: spi-geni-qcom: Use the new method of gpio CS control
drivers/platform/chrome/cros_ec_spi.c | 2 --
drivers/spi/spi-geni-qcom.c | 1 +
2 files changed, 1 insertion(+), 2 deletions(-)
base-commit: b650545978
--
https://chromeos.dev
Raydium device does not like splitting of tx transactions into multiple
messages - one for the register address and one for the actual data. This
results in incorrect behavior on the device side.
This change updates raydium_i2c_read and raydium_i2c_write to create
i2c_msg arrays separately and passes those arrays into raydium_i2c_xfer
which decides based on the address whether the bank switch command should
be sent. The bank switch header is still added by raydium_i2c_read and
raydium_i2c_write to ensure that all these operations are performed as part
of a single I2C transfer. It guarantees that no other transactions are
initiated to any other device on the same bus after the bank switch command
is sent.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Link: https://lore.kernel.org/r/20201205005941.1427643-1-furquan@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fix for 'RETRIGEN' handling in Atmel touch controllers that was
causing lost interrupts on systems using edge-triggered interrupts, a
quirk for i8042 driver, and a couple more fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - fix lost interrupts
Input: xpad - support Ardwiino Controllers
Input: i8042 - add ByteSpeed touchpad to noloop table
Input: i8042 - fix error return code in i8042_setup_aux()
Input: soc_button_array - add missing include
After commit 74d905d2d3 devices requiring the workaround for edge
triggered interrupts stopped working.
The hardware needs the quirk to be used before even proceeding to
check if the quirk is needed because mxt_acquire_irq() is called
before mxt_check_retrigen() is called and at this point pending IRQs
need to be checked, and if the workaround is not active, all
interrupts will be lost from this point.
Solve this by switching the calls around.
Reported-by: Andre Müller <andre.muller@web.de>
Tested-by: Andre Müller <andre.muller@web.de>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 74d905d2d3 ("Input: atmel_mxt_ts - only read messages in mxt_acquire_irq() when necessary")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201201123026.1416743-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/goodix.c:1168: warning: Function parameter or member 'ctx' not described in 'goodix_config_cb'
drivers/input/touchscreen/goodix.c:1168: warning: Excess function parameter 'ts' description in 'goodix_config_cb'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-14-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/wm97xx-core.c:204: warning: Function parameter or member 'status' not described in 'wm97xx_set_gpio'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201112110204.2083435-12-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/surface3_spi.c: In function ‘surface3_spi_process_touch’:
drivers/input/touchscreen/surface3_spi.c:97:6: warning: variable ‘timestamp’ set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/surface3_spi.c:225: warning: Function parameter or member 'data' not described in 'surface3_spi_get_gpio_config'
drivers/input/touchscreen/surface3_spi.c:225: warning: Excess function parameter 'ts' description in 'surface3_spi_get_gpio_config'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-11-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/goodix.c:569: warning: Function parameter or member 'len' not described in 'goodix_check_cfg'
drivers/input/touchscreen/goodix.c:587: warning: Function parameter or member 'len' not described in 'goodix_send_cfg'
drivers/input/touchscreen/goodix.c:1165: warning: Function parameter or member 'cfg' not described in 'goodix_config_cb'
drivers/input/touchscreen/goodix.c:1165: warning: Function parameter or member 'ctx' not described in 'goodix_config_cb'
drivers/input/touchscreen/goodix.c:1165: warning: Excess function parameter 'ts' description in 'goodix_config_cb'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-5-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds the code for the Atmel touchscreens such as mXT224 to obtain
power regulators for the supply voltages AVDD and VDD. On mobile phones
such as Samsung GT-I8190 (Golden) this is needed to explicitly bring power
online.
We just enable the regulators at probe() and disable them at remove()
or in the error path for now.
As regulators are naturally stubbed if not available, this should have no
impact on existing systems.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-3-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver uses GPIO descriptors to drive the touchscreen RESET line. In
the existing device trees this has in conflict with intution been flagged
as GPIO_ACTIVE_HIGH and the driver then applies the reverse action by
driving the line low (setting to 0) to enter reset state and driving the
line high (setting to 1) to get out of reset state.
The correct way to handle active low GPIO lines is to provide the
GPIO_ACTIVE_LOW in the device tree (thus properly describing the hardware)
and letting the GPIO framework invert the assertion (driving high) to a
low level and vice versa.
This is considered a bug since the device trees are incorrectly
mis-specifying the line as active high.
Fix the driver and all device trees specifying a reset line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl+DdgYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGB1sH/0B4REolPPxiQsPL
P45+a2POUU0SQK8NjkcYskQmJ6DnPKkJSXeUU8rzuI2rty5bWEzEBxdUSh064ZaM
DGxkWrdhYNaLJuceNLlanBk3vrM3KwGkaJFSKLgsEXkmH86gl33ptA8nlQVbfc+4
FK4hRZs2J6Y5YRsuzPO8nzzHWs1CThZEcwNPOeIZrAnv+/13zyP/piZ+R/2gKYwy
RVrVrzSTkTGJXotn6J17Sa02+CGv5UqdxOZFv7jimYJOmFT7KnGngNrJbh8aYWk7
vPTRUvGozh6NyYxtRI9LKGZy1yQ05Cl7N927CnFYzD235/eT7zaRDZe1e1JaIE8Z
r2yxGCM=
=ZIYP
-----END PGP SIGNATURE-----
Merge tag 'v5.9' into next
Sync up with mainline to bring in the latest DTS files.
This is essentially a revert of:
3ac8bf077d ("[PATCH] ads7846: sparc32 warning fix")
By now enable_irq() and disable_irq() are properly defined in
linux/interrupt.h and we do not need to pull in architecture-specific
bits.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
req->sample[1] is not naturally aligned at word boundary, and therefore we
should use get_unaligned_be16() when accessing it.
Fixes: 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845 controller support")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201113112240.1360-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Starting with 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845
controller support"), the ads7845 was partially converted to full duplex
mode.
Since it is not touchscreen controller specific, it is better to extend
this conversion to cover entire driver. This will reduce CPU load and make
driver more readable.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201110085041.16303-2-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If touchscreen is released while busy reading HWMON device, the release
can be missed. The IRQ thread is not started because no touch is active
and BTN_TOUCH release event is never sent.
Fixes: f5a28a7d48 ("Input: ads7846 - avoid pen up/down when reading hwmon")
Co-developed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201027105416.18773-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fix for use-after-free in the Sun keyboard driver, a fix to firmware
updates on newer ICs in the Elan touchpad diver, and a couple misc
driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - fix firmware update on newer ICs
Input: resistive-adc-touch - fix kconfig dependency on IIO_BUFFER
Input: sunkbd - avoid use-after-free in teardown paths
Input: i8042 - allow insmod to succeed on devices without an i8042 controller
Input: adxl34x - clean up a data type in adxl34x_probe()
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/imx6ul_tsc.c: In function ‘adc_irq_fn’:
drivers/input/touchscreen/imx6ul_tsc.c:307:6: warning: variable ‘value’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20201112110204.2083435-6-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do not overwrite spi->mode flags set by spi framework, otherwise the
chip select polarity will get lost.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20201027095724.18654-3-o.rempel@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Hard-coding resolution for st1633 device was wrong. Some of LCDs like
YTS700TLBC-02-100C has assembled Sitronix st1633 touchcontroller too. But
the resolution is not 320x480 as was hard-coded.
Add new function which reads correct resolution directly from register.
Signed-off-by: Andrej Valek <andrej.valek@siemens.com>
Link: https://lore.kernel.org/r/20201103073949.12198-1-andrej.valek@siemens.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When TOUCHSCREEN_ADC is enabled and IIO_BUFFER is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_BUFFER_CB
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- TOUCHSCREEN_ADC [=y] && !UML && INPUT [=y] && INPUT_TOUCHSCREEN [=y] && IIO [=y]
The reason is that TOUCHSCREEN_ADC selects IIO_BUFFER_CB without depending
on or selecting IIO_BUFFER while IIO_BUFFER_CB depends on IIO_BUFFER. This
can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: aa132ffb6b ("input: touchscreen: resistive-adc-touch: add generic resistive ADC touchscreen")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201102221504.541279-1-fazilyildiran@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/input/touchscreen/cyttsp_i2c_common.c:24:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/input/touchscreen/cyttsp4_i2c.c:17:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char * const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/input/touchscreen/cyttsp4_spi.c:17:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char * const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-16-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The eKTF2132 is a touchscreen controller found, for example, in the Kobo
Aura ebook reader. It is similar to the ektf2127, but it uses a different
packet type to report touch events.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20201106112412.390724-3-j.neuschaefer@gmx.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
Add support for the bt541 touchscreen IC from zinitix, loosely based on
downstream driver. The driver currently supports multitouch (5 touch points).
The bt541 seems to support touch keys, but the support was not added because
that functionality is not being utilized by the touchscreen used for testing.
Based on the similartities between downstream drivers, it seems likely that
other similar touchscreen ICs can be supported with this driver in the future.
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Link: https://lore.kernel.org/r/20201001122949.16846-1-michael.srba@seznam.cz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In stmfts_sysfs_hover_enable_write(), we should check value and
sdata->hover_enabled is all true.
Fixes: 78bcac7b2a ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200916141941.16684-1-yuehaibing@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If imx6ul_tsc_init() fails then we need to clean up the clocks.
I reversed the "if (input_dev->users) {" condition to make the code a
bit simpler.
Fixes: 6cc527b058 ("Input: imx6ul_tsc - propagate the errors")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200905124942.GC183976@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds a new behavior to report touch major resolution
based on information provided by firmware.
In initial process, driver acquires touch information from touch ic.
It contains one byte about the resolution value of ABS_MT_TOUCH_MAJOR.
Touch driver will report touch major resolution by this information.
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Link: https://lore.kernel.org/r/1598581195-9874-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
