if of_find_device_by_node() succeed, usbmisc_get_init_data() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: ef12da914e ("usb: chipidea: imx: properly check for usbmisc")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201117011430.642589-1-yukuai3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the MTU size issue with RX packet size as the host sends the packet
with extra bytes containing ethernet header. This causes failure when
user sets the MTU size to the maximum i.e. 15412. In this case the
ethernet packet received will be of length 15412 plus the ethernet header
length. This patch fixes the issue where there is a check that RX packet
length must not be more than max packet length.
Fixes: bba787a860 ("usb: gadget: ether: Allow jumbo frames")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1605597215-122027-1-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spinlock lockup as part of composite_disconnect
when it tries to acquire cdev->lock as part of usb_gadget_deactivate.
This is because the usb_gadget_deactivate is called from
usb_function_deactivate with the same spinlock held.
This would result in the below call stack and leads to stall.
rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
rcu: 3-...0: (1 GPs behind) idle=162/1/0x4000000000000000
softirq=10819/10819 fqs=2356
(detected by 2, t=5252 jiffies, g=20129, q=3770)
Task dump for CPU 3:
task:uvc-gadget_wlhe state:R running task stack: 0 pid: 674 ppid:
636 flags:0x00000202
Call trace:
__switch_to+0xc0/0x170
_raw_spin_lock_irqsave+0x84/0xb0
composite_disconnect+0x28/0x78
configfs_composite_disconnect+0x68/0x70
usb_gadget_disconnect+0x10c/0x128
usb_gadget_deactivate+0xd4/0x108
usb_function_deactivate+0x6c/0x80
uvc_function_disconnect+0x20/0x58
uvc_v4l2_release+0x30/0x88
v4l2_release+0xbc/0xf0
__fput+0x7c/0x230
____fput+0x14/0x20
task_work_run+0x88/0x140
do_notify_resume+0x240/0x6f0
work_pending+0x8/0x200
Fix this by doing an unlock on cdev->lock before the usb_gadget_deactivate
call from usb_function_deactivate.
The same lockup can happen in the usb_gadget_activate path. Fix that path
as well.
Reported-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/linux-usb/20201102094936.GA29581@b29397-desktop/
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201202130220.24926-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When printer driver is loaded, the printer_func_bind function is called, in
this function, the interface descriptor be allocated memory, if after that,
the error occurred, the interface descriptor memory need to be free.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Zqiang <qiang.zhang@windriver.com>
Link: https://lore.kernel.org/r/20201210020148.6691-1-qiang.zhang@windriver.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.
It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:
usb 1-2: can't set config #1, error -28
This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.
Fixes: 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Warm reboot scenarios some times type C Mux driver gets Mux configuration
request as HPD=1,IRQ=1. In that scenario typeC Mux driver need to configure
Mux as follows as per IOM requirement:
(1). Confgiure Mux HPD = 1, IRQ = 0
(2). Configure Mux with HPD = 1, IRQ = 1
IOM expects TypeC Mux configuration as follows:
(1). HPD=1, IRQ=0
(2). HPD=1, IRQ=1
if IOM gets mux config request (2) without configuring (1), it will ignore
the request. The impact of this is there is no DP_alt mode display.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Link: https://lore.kernel.org/r/20201216140918.49197-1-madhusudanarao.amara@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting UAF at usb_submit_urb() [1], for
service_outstanding_interrupt() is not checking WDM_DISCONNECTING
before calling usb_submit_urb(). Close the race by doing same checks
wdm_read() does upon retry.
Also, while wdm_read() checks WDM_DISCONNECTING with desc->rlock held,
service_interrupt_work() does not hold desc->rlock. Thus, it is possible
that usb_submit_urb() is called from service_outstanding_interrupt() from
service_interrupt_work() after WDM_DISCONNECTING was set and kill_urbs()
from wdm_disconnect() completed. Thus, move kill_urbs() in
wdm_disconnect() to after cancel_work_sync() (which makes sure that
service_interrupt_work() is no longer running) completed.
Although it seems to be safe to dereference desc->intf->dev in
service_outstanding_interrupt() even if WDM_DISCONNECTING was already set
because desc->rlock or cancel_work_sync() prevents wdm_disconnect() from
reaching list_del() before service_outstanding_interrupt() completes,
let's not emit error message if WDM_DISCONNECTING is set by
wdm_disconnect() while usb_submit_urb() is in progress.
[1] https://syzkaller.appspot.com/bug?extid=9e04e2df4a32fb661daf
Reported-by: syzbot <syzbot+9e04e2df4a32fb661daf@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/620e2ee0-b9a3-dbda-a25b-a93e0ed03ec5@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, and this driver
was only used by the old non-DT i.MX devices.
Remove the driver as it has no users left.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201210210413.15262-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is supported by the IR Toy driver.
Reported-by: Georgi Bakalski <georgi.bakalski@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201227134502.4548-2-sean@mess.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Switch to the generic C VDSO, as well as some cleanups of our VDSO
setup/handling code.
- Support for KUAP (Kernel User Access Prevention) on systems using the hashed
page table MMU, using memory protection keys.
- Better handling of PowerVM SMT8 systems where all threads of a core do not
share an L2, allowing the scheduler to make better scheduling decisions.
- Further improvements to our machine check handling.
- Show registers when unwinding interrupt frames during stack traces.
- Improvements to our pseries (PowerVM) partition migration code.
- Several series from Christophe refactoring and cleaning up various parts of
the 32-bit code.
- Other smaller features, fixes & cleanups.
Thanks to:
Alan Modra, Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Ard
Biesheuvel, Athira Rajeev, Balamuruhan S, Bill Wendling, Cédric Le Goater,
Christophe Leroy, Christophe Lombard, Colin Ian King, Daniel Axtens, David
Hildenbrand, Frederic Barrat, Ganesh Goudar, Gautham R. Shenoy, Geert
Uytterhoeven, Giuseppe Sacco, Greg Kurz, Harish, Jan Kratochvil, Jordan
Niethe, Kaixu Xia, Laurent Dufour, Leonardo Bras, Madhavan Srinivasan, Mahesh
Salgaonkar, Mathieu Desnoyers, Nathan Lynch, Nicholas Piggin, Oleg Nesterov,
Oliver O'Halloran, Oscar Salvador, Po-Hsu Lin, Qian Cai, Qinglang Miao, Randy
Dunlap, Ravi Bangoria, Sachin Sant, Sandipan Das, Sebastian Andrzej Siewior ,
Segher Boessenkool, Srikar Dronamraju, Tyrel Datwyler, Uwe Kleine-König,
Vincent Stehlé, Youling Tang, Zhang Xiaoxu.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEJFGtCPCthwEv2Y/bUevqPMjhpYAFAl/bURITHG1wZUBlbGxl
cm1hbi5pZC5hdQAKCRBR6+o8yOGlgEzBEAC1Vwibcog2P9rkJPb0q3UGWSYSx25V
h/LwwxtM9Tm14j/LZsSgkOgIsfMaWEBIw/8D4efQ7AX9aFo+R0c2DdQMx1MG5MXz
gZk58+l3LwId6h9+OrwurpEW+ZmURLAtGMSyFdkeiZ3/XTnkbf1XnewC0QWQe56a
EGLmjx1MFl45jspoy7UIUXsXoNJIfflEKhrgUzSUh8X2eLmvB9ws6A4BXxbVzyZl
lZv3+uWimU2pFgdkB9jOCxoG4zFEr2o5ovLHG7zCCVo5JoXmTPQ5cMVBraH206ms
+5vCmu4qI8uP5UlZW/mZfhrtDiMdHdQqqFOaQwVlOmoUbU6L6E6rxm3iVnov2Bbi
iUgxoeJDxAb2cM2EWFK6oWVgr7+NkwvXM1IG8xtprhHrCdnC9r+psQr/dswb3LSg
MJ7u/RCq3uixy2kWP8E0NEHw7ngQZ/ZKPqzfnmIWOC7tYUxgaL02I8Ff9/ZXAI2J
CnmqFYOjrimHkcwXGOtKkXNvfU0DiL97qpK2AQNWElE8+bUUmpw+ltUrsdSycYmv
Afc4WIcVrTA+a9laSLgjdZbolbNSa3p+cMIYdPrVx9g+xqygbxIKv+EDGNv1WHfD
GU1gmohMY+ZkMOvFRMi8LAsEm0DH/etWE0py/8uyxDYKnGyD1Ur6452DStkmgGb2
azmcaOyLdb+HXA==
=Ga3K
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Switch to the generic C VDSO, as well as some cleanups of our VDSO
setup/handling code.
- Support for KUAP (Kernel User Access Prevention) on systems using the
hashed page table MMU, using memory protection keys.
- Better handling of PowerVM SMT8 systems where all threads of a core
do not share an L2, allowing the scheduler to make better scheduling
decisions.
- Further improvements to our machine check handling.
- Show registers when unwinding interrupt frames during stack traces.
- Improvements to our pseries (PowerVM) partition migration code.
- Several series from Christophe refactoring and cleaning up various
parts of the 32-bit code.
- Other smaller features, fixes & cleanups.
Thanks to: Alan Modra, Alexey Kardashevskiy, Andrew Donnellan, Aneesh
Kumar K.V, Ard Biesheuvel, Athira Rajeev, Balamuruhan S, Bill Wendling,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King,
Daniel Axtens, David Hildenbrand, Frederic Barrat, Ganesh Goudar,
Gautham R. Shenoy, Geert Uytterhoeven, Giuseppe Sacco, Greg Kurz,
Harish, Jan Kratochvil, Jordan Niethe, Kaixu Xia, Laurent Dufour,
Leonardo Bras, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu
Desnoyers, Nathan Lynch, Nicholas Piggin, Oleg Nesterov, Oliver
O'Halloran, Oscar Salvador, Po-Hsu Lin, Qian Cai, Qinglang Miao, Randy
Dunlap, Ravi Bangoria, Sachin Sant, Sandipan Das, Sebastian Andrzej
Siewior , Segher Boessenkool, Srikar Dronamraju, Tyrel Datwyler, Uwe
Kleine-König, Vincent Stehlé, Youling Tang, and Zhang Xiaoxu.
* tag 'powerpc-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (304 commits)
powerpc/32s: Fix cleanup_cpu_mmu_context() compile bug
powerpc: Add config fragment for disabling -Werror
powerpc/configs: Add ppc64le_allnoconfig target
powerpc/powernv: Rate limit opal-elog read failure message
powerpc/pseries/memhotplug: Quieten some DLPAR operations
powerpc/ps3: use dma_mapping_error()
powerpc: force inlining of csum_partial() to avoid multiple csum_partial() with GCC10
powerpc/perf: Fix Threshold Event Counter Multiplier width for P10
powerpc/mm: Fix hugetlb_free_pmd_range() and hugetlb_free_pud_range()
KVM: PPC: Book3S HV: Fix mask size for emulated msgsndp
KVM: PPC: fix comparison to bool warning
KVM: PPC: Book3S: Assign boolean values to a bool variable
powerpc: Inline setup_kup()
powerpc/64s: Mark the kuap/kuep functions non __init
KVM: PPC: Book3S HV: XIVE: Add a comment regarding VP numbering
powerpc/xive: Improve error reporting of OPAL calls
powerpc/xive: Simplify xive_do_source_eoi()
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_EOI_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_MASK_FW
powerpc/xive: Remove P9 DD1 flag XIVE_IRQ_FLAG_SHIFT_BUG
...
-----BEGIN PGP SIGNATURE-----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=zo4w
-----END PGP SIGNATURE-----
Merge tag 'for-5.11/block-2020-12-14' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"Another series of killing more code than what is being added, again
thanks to Christoph's relentless cleanups and tech debt tackling.
This contains:
- blk-iocost improvements (Baolin Wang)
- part0 iostat fix (Jeffle Xu)
- Disable iopoll for split bios (Jeffle Xu)
- block tracepoint cleanups (Christoph Hellwig)
- Merging of struct block_device and hd_struct (Christoph Hellwig)
- Rework/cleanup of how block device sizes are updated (Christoph
Hellwig)
- Simplification of gendisk lookup and removal of block device
aliasing (Christoph Hellwig)
- Block device ioctl cleanups (Christoph Hellwig)
- Removal of bdget()/blkdev_get() as exported API (Christoph Hellwig)
- Disk change rework, avoid ->revalidate_disk() (Christoph Hellwig)
- sbitmap improvements (Pavel Begunkov)
- Hybrid polling fix (Pavel Begunkov)
- bvec iteration improvements (Pavel Begunkov)
- Zone revalidation fixes (Damien Le Moal)
- blk-throttle limit fix (Yu Kuai)
- Various little fixes"
* tag 'for-5.11/block-2020-12-14' of git://git.kernel.dk/linux-block: (126 commits)
blk-mq: fix msec comment from micro to milli seconds
blk-mq: update arg in comment of blk_mq_map_queue
blk-mq: add helper allocating tagset->tags
Revert "block: Fix a lockdep complaint triggered by request queue flushing"
nvme-loop: use blk_mq_hctx_set_fq_lock_class to set loop's lock class
blk-mq: add new API of blk_mq_hctx_set_fq_lock_class
block: disable iopoll for split bio
block: Improve blk_revalidate_disk_zones() checks
sbitmap: simplify wrap check
sbitmap: replace CAS with atomic and
sbitmap: remove swap_lock
sbitmap: optimise sbitmap_deferred_clear()
blk-mq: skip hybrid polling if iopoll doesn't spin
blk-iocost: Factor out the base vrate change into a separate function
blk-iocost: Factor out the active iocgs' state check into a separate function
blk-iocost: Move the usage ratio calculation to the correct place
blk-iocost: Remove unnecessary advance declaration
blk-iocost: Fix some typos in comments
blktrace: fix up a kerneldoc comment
block: remove the request_queue to argument request based tracepoints
...
Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be more
and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iDZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRMACgqxKS2CUcY8tPnR5weHEsbz6O+KAAn3BtEFnK
7V9EnSuZe4L1jNOHOB5V
=xzHh
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
Here is the big driver core updates for 5.11-rc1
This time there was a lot of different work happening here for some
reason:
- redo of the fwnode link logic, speeding it up greatly
- auxiliary bus added (this was a tag that will be pulled in
from other trees/maintainers this merge window as well, as
driver subsystems started to rely on it)
- platform driver core cleanups on the way to fixing some
long-time api updates in future releases
- minor fixes and tweaks.
All have been in linux-next with no (finally) reported issues. Testing
there did helped in shaking issues out a lot :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iEUQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynBJwCgjBAtVWXquZz4m/pyjn0HoTC7tdYAnAlQIj9s
vRbPjOgH9R+YRJzFs1Kx
=X6UP
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core updates for 5.11-rc1
This time there was a lot of different work happening here for some
reason:
- redo of the fwnode link logic, speeding it up greatly
- auxiliary bus added (this was a tag that will be pulled in from
other trees/maintainers this merge window as well, as driver
subsystems started to rely on it)
- platform driver core cleanups on the way to fixing some long-time
api updates in future releases
- minor fixes and tweaks.
All have been in linux-next with no (finally) reported issues. Testing
there did helped in shaking issues out a lot :)"
* tag 'driver-core-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (39 commits)
driver core: platform: don't oops in platform_shutdown() on unbound devices
ACPI: Use fwnode_init() to set up fwnode
misc: pvpanic: Replace OF headers by mod_devicetable.h
misc: pvpanic: Combine ACPI and platform drivers
usb: host: sl811: Switch to use platform_get_mem_or_io()
vfio: platform: Switch to use platform_get_mem_or_io()
driver core: platform: Introduce platform_get_mem_or_io()
dyndbg: fix use before null check
soc: fix comment for freeing soc_dev_attr
driver core: platform: use bus_type functions
driver core: platform: change logic implementing platform_driver_probe
driver core: platform: reorder functions
driver core: make driver_probe_device() static
driver core: Fix a couple of typos
driver core: Reorder devices on successful probe
driver core: Delete pointless parameter in fwnode_operations.add_links
driver core: Refactor fw_devlink feature
efi: Update implementation of add_links() to create fwnode links
of: property: Update implementation of add_links() to create fwnode links
driver core: Use device's fwnode to check if it is waiting for suppliers
...
Here is the big USB and thunderbolt pull request for 5.11-rc1.
Nothing major in here, just the grind of constant development to support
new hardware and fix old issues:
- thunderbolt updates for new USB4 hardware
- cdns3 major driver updates
- lots of typec updates and additions as more hardware is available
- usb serial driver updates and fixes
- other tiny USB driver updates
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iKFQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yme2gCfacEYztlnc0fh7PyyatYXgdkspbYAn2ri6mfF
4VY86HYXKqQRDW8w/lSg
=f8KJ
-----END PGP SIGNATURE-----
Merge tag 'usb-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big USB and thunderbolt pull request for 5.11-rc1.
Nothing major in here, just the grind of constant development to
support new hardware and fix old issues:
- thunderbolt updates for new USB4 hardware
- cdns3 major driver updates
- lots of typec updates and additions as more hardware is available
- usb serial driver updates and fixes
- other tiny USB driver updates
All have been in linux-next with no reported issues"
* tag 'usb-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (172 commits)
usb: phy: convert comma to semicolon
usb: ucsi: convert comma to semicolon
usb: typec: tcpm: convert comma to semicolon
usb: typec: tcpm: Update vbus_vsafe0v on init
usb: typec: tcpci: Enable bleed discharge when auto discharge is enabled
usb: typec: Add class for plug alt mode device
USB: typec: tcpci: Add Bleed discharge to POWER_CONTROL definition
USB: typec: tcpm: Add a 30ms room for tPSSourceOn in PR_SWAP
USB: typec: tcpm: Fix PR_SWAP error handling
USB: typec: tcpm: Hard Reset after not receiving a Request
USB: gadget: f_fs: remove likely/unlikely
usb: gadget: f_fs: Re-use SS descriptors for SuperSpeedPlus
USB: gadget: f_midi: setup SuperSpeed Plus descriptors
USB: gadget: f_acm: add support for SuperSpeed Plus
USB: gadget: f_rndis: fix bitrate for SuperSpeed and above
usb: typec: intel_pmc_mux: Configure cable generation value for USB4
MAINTAINERS: Add myself as a reviewer for CADENCE USB3 DRD IP DRIVER
usb: chipidea: ci_hdrc_imx: Use of_device_get_match_data()
usb: chipidea: usbmisc_imx: Use of_device_get_match_data()
usb: cdns3: fix NULL pointer dereference on no platform data
...
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support
-----BEGIN PGP SIGNATURE-----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=c9rl
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a huge amount of big things here, AMD has support for a few new HW
variants (vangogh, green sardine, dimgrey cavefish), Intel has some
more DG1 enablement. We have a few big reworks of the TTM layers and
interfaces, GEM and atomic internal API reworks cross tree. fbdev is
marked orphaned in here as well to reflect the current reality.
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support"
* tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm: (1754 commits)
drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs
drm/amdgpu: fix size calculation with stolen vga memory
drm/amdgpu: remove amdgpu_ttm_late_init and amdgpu_bo_late_init
drm/amdgpu: free the pre-OS console framebuffer after the first modeset
drm/amdgpu: enable runtime pm using BACO on CI dGPUs
drm/amdgpu/cik: enable BACO reset on Bonaire
drm/amd/pm: update smu10.h WORKLOAD_PPLIB setting for raven
drm/amd/pm: remove one unsupported smu function for vangogh
drm/amd/display: setup system context for APUs
drm/amd/display: add S/G support for Vangogh
drm/amdkfd: Fix leak in dmabuf import
drm/amdgpu: use AMDGPU_NUM_VMID when possible
drm/amdgpu: fix sdma instance fw version and feature version init
drm/amd/pm: update driver if version for dimgrey_cavefish
drm/amd/display: 3.2.115
drm/amd/display: [FW Promotion] Release 0.0.45
drm/amd/display: Revert DCN2.1 dram_clock_change_latency update
drm/amd/display: Enable gpu_vm_support for dcn3.01
drm/amd/display: Fixed the audio noise during mode switching with HDCP mode on
drm/amd/display: Add wm table for Renoir
...
Replace a comma between expression statements by a semicolon.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211085510.2928-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 5.11-rc1, including:
- keyspan_pda write-implementation fixes
- digi_acceleport write-wakeup fix
- mos7720 parport-restore fix
- mos7720 parport-tasklet removal
- cp210x termios-handling cleanups
- option device-flag fix
- ftdi_sio GPIO CBUS-configuration improvements
- removal of in_interrupt() uses
Included are also various clean ups.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCX9OIiQAKCRALxc3C7H1l
CA1OAQCZVi5abi2R/+Rr3V9/iYOA/VJXJ6Mxg8xDbt3GWmp0lQD9G4z0Ws4f1RY1
ACEcOBNQedpoxXa/o3eb8tlAjObwAwg=
=udri
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.11-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.11-rc1
Here are the USB-serial updates for 5.11-rc1, including:
- keyspan_pda write-implementation fixes
- digi_acceleport write-wakeup fix
- mos7720 parport-restore fix
- mos7720 parport-tasklet removal
- cp210x termios-handling cleanups
- option device-flag fix
- ftdi_sio GPIO CBUS-configuration improvements
- removal of in_interrupt() uses
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.11-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (30 commits)
USB: serial: ftdi_sio: log the CBUS GPIO validity
USB: serial: ftdi_sio: drop GPIO line checking dead code
USB: serial: ftdi_sio: report the valid GPIO lines to gpiolib
USB: serial: option: add interface-number sanity check to flag handling
USB: serial: cp210x: clean up dtr_rts()
USB: serial: cp210x: refactor flow-control handling
USB: serial: cp210x: drop flow-control debugging
USB: serial: cp210x: set terminal settings on open
USB: serial: cp210x: clean up line-control handling
USB: serial: cp210x: return early on unchanged termios
USB: serial: mos7720: defer state restore to a workqueue
USB: serial: mos7720: fix parallel-port state restore
USB: serial: remove write wait queue
USB: serial: digi_acceleport: fix write-wakeup deadlocks
USB: serial: keyspan_pda: drop redundant usb-serial pointer
USB: serial: keyspan_pda: use BIT() macro
USB: serial: keyspan_pda: clean up comments and whitespace
USB: serial: keyspan_pda: clean up xircom/entrega support
USB: serial: keyspan_pda: add write-fifo support
USB: serial: keyspan_pda: increase transmitter threshold
...
Replace a comma between expression statements by a semicolon.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211085553.2982-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During init, vbus_vsafe0v does not get updated till the first
connect as a sink. This causes TCPM to be stuck in SRC_ATTACH_WAIT
state while booting with a sink (For instance: a headset) connected.
[ 1.429168] Start toggling
[ 1.439907] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 1.445242] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 53.358528] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 53.358564] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
Fix this by updating vbus_vsafe0v based on vbus_present status
on boot.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201211071911.2205197-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Auto discharge circuits kick in only when vbus decays and reaches
VBUS_SINK_DISCONNECT_THRESHOLD threshold. Enable bleed discharge to
discharge vbus to VBUS_SINK_DISCONNECT_THRESHOLD upon disconnect.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201211071145.2199997-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the Type C class for plug alternate mode devices which are being
registered by the Type C connector class. This ensures that udev events
get generated when the plug alt modes are registered.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20201210211653.879044-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM state machine needs 20-25ms to enter the ErrorRecovery state after
tPSSourceOn timer timeouts. Change the timer from max 480ms to 450ms to
ensure that the timer complies with the Spec. In order to keep the
flexibility for other usecases using tPSSourceOn, add another timer only
for PR_SWAP.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD rev3.0 8.3.3.16.3.6 PE_PRS_SRC_SNK_Wait_Source_on State
The Policy Enging Shall transition to the ErrorRecovery state when the
PSSourceOnTimer times out ...
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD 3.0 spec 8.3.3.2.3, A Get_Source_Cap message is sent
to a UUT that is in the PE_SRC_Ready state. After sending
a Source_Capabilities message, the UUT should then expect
a Request message in response. When one is not received,
the UUT should timeout to PE_SRC_Hard_Reset.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: pumahsu <pumahsu@google.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to use new platform_get_mem_or_io() instead of home grown analogue.
Note, the code has been moved upper in the function to allow farther cleanups,
such as resource sanity check.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201209203642.27648-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They are used way too often in this file, in some ways that are actually
wrong. Almost all of these are already known by the compiler and CPU so
just remove them all as none of these should be on any "hot paths" where
it actually matters.
Cc: Felipe Balbi <balbi@kernel.org>
Reported-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201127140559.381351-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In many cases a function that supports SuperSpeed can very well
operate in SuperSpeedPlus, if a gadget controller supports it,
as the endpoint descriptors (and companion descriptors) are
generally identical and can be re-used. This is true for two
commonly used functions: Android's ADB and MTP. So we can simply
assign the usb_function's ssp_descriptors array to point to its
ss_descriptors, if available. Similarly, we need to allow an
epfile's ioctl for FUNCTIONFS_ENDPOINT_DESC to correctly
return the corresponding SuperSpeed endpoint descriptor in case
the connected speed is SuperSpeedPlus as well.
The only exception is if a function wants to implement an
Isochronous endpoint capable of transferring more than 48KB per
service interval when operating at greater than USB 3.1 Gen1
speed, in which case it would require an additional SuperSpeedPlus
Isochronous Endpoint Companion descriptor to be returned as part
of the Configuration Descriptor. Support for that would need
to be separately added to the userspace-facing FunctionFS API
which may not be a trivial task--likely a new descriptor format
(v3?) may need to be devised to allow for separate SS and SSP
descriptors to be supplied.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201027230731.9073-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Needed for SuperSpeed Plus support for f_midi. This allows the
gadget to work properly without crashing at SuperSpeed rates.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201127140559.381351-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setup the SuperSpeed Plus descriptors for f_acm. This allows the gadget
to work properly without crashing at SuperSpeed rates.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: taehyun.cho <taehyun.cho@samsung.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201127140559.381351-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align the SuperSpeed Plus bitrate for f_rndis to match f_ncm's ncm_bitrate
defined by commit 1650113888 ("usb: gadget: f_ncm: add SuperSpeed descriptors
for CDC NCM").
Cc: Felipe Balbi <balbi@kernel.org>
Cc: EJ Hsu <ejh@nvidia.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201127140559.381351-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 specification chapter 3 indicates that cable data rates have to be
rounded for USB4 device to operate as USB4.
With that configure cable generation value to use rounded data rates for
USB4.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20201209042408.23079-2-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Chipidea USB2:
- Add tracepoint support for UDC
- Some tiny improvements
For Cadence USB3
- Add some quirks for host mode, and let host work well at more use cases
* SKIP_PHY_INIT
* Disable BEI
* Enable runtime PM default for i.mx platform
- Some tiny improvements
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl/R7S0ACgkQSFkpgVDW
cbv/QQf+KhHOZYYzGMZXvyDiFIoE28sfrxyTrZKoDUXIWuAsLegpvY/bw6YJxAZy
bj8z/iAk6NOyQLMH+2ULQoJfc8GX18O05ZOSKg+prcIw5e398TEH0NFrJZV/0dBa
VSk0+pGaRvn6jLfw/lF2EImf4gHLh4EsgDOgWn4ffZL3IRwmGPub2splppmu9N88
1fbrxexc5NORnIpigH0kkftPQkda7slPfo3pMRjpHHb49SDQVw0C2x6FPooQxoaz
c7DWEKfy2E8OcRDCgFdFFLIZNELSlvLHXOk1H8taTXlcVSHHFgos69qzCdOeiRuq
OMHzsRM+M2XEb7LlSPYU0+G/K6SXFQ==
=dV/G
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Below are main changes for v5.11-rc1:
For Chipidea USB2:
- Add tracepoint support for UDC
- Some tiny improvements
For Cadence USB3
- Add some quirks for host mode, and let host work well at more use cases
* SKIP_PHY_INIT
* Disable BEI
* Enable runtime PM default for i.mx platform
- Some tiny improvements
* tag 'usb-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
MAINTAINERS: Add myself as a reviewer for CADENCE USB3 DRD IP DRIVER
usb: chipidea: ci_hdrc_imx: Use of_device_get_match_data()
usb: chipidea: usbmisc_imx: Use of_device_get_match_data()
usb: cdns3: fix NULL pointer dereference on no platform data
usb: chipidea: trace: fix the endian issue
usb: chipidea: add tracepoint support for udc
doc: dt-binding: cdns,usb3: add wakeup-irq
usb: cdns3: imx: enable runtime pm by default
usb: cdns3: add quirk for enable runtime pm by default
usb: cdns3: host: disable BEI support
usb: cdns3: host: add xhci_plat_priv quirk XHCI_SKIP_PHY_INIT
usb: cdns3: host: add .suspend_quirk for xhci-plat.c
usb: cdns3: Rids of duplicate error message
usb: cdns3: Add static to cdns3_gadget_exit function
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Some platforms (e.g. TI) will not have any platform data which will
lead to NULL pointer dereference if we don't check for NULL pdata.
Fixes: 7cea965775 ("usb: cdns3: add quirk for enable runtime pm by default")
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Some vendors (eg: NXP) may want to enable runtime pm by default for
power saving, add one quirk for it.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The Cadence xHCI doesn't support BEI well, it causes the disconnection
of ISOC devices can't be detected, so we disable it.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
cdns3 manages PHY by own DRD driver, so skip the management by
HCD core.
Reviewed-by: Jun Li <jun.li@nxp.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
cdns3 has some special PM sequence between xhci_bus_suspend and
xhci_suspend, add quirk to implement it.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
On failure, the platform_get_irq_byname prints an error message,
so patch removes error message related to this function from
core.c file.
A change was suggested during reviewing CDNSP driver by Chunfeng Yun.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Function cdns3_gadget_exit is used only in gadget.c file.
This patch removes declaration and definition of this
function from gadget-export.h file and makes it static.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
UAS does not share the pessimistic assumption storage is making that
devices cannot deal with WRITE_SAME. A few devices supported by UAS,
are reported to not deal well with WRITE_SAME. Those need a quirk.
Add it to the device that needs it.
Reported-by: David C. Partridge <david.partridge@perdrix.co.uk>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201209152639.9195-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The validity of the ftdi CBUS GPIO is pretty hidden so far,
and finding out *why* some GPIOs don't work is sometimes
hard to identify. So let's help the user by displaying the
map of the CBUS pins that are valid for a GPIO.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201204164739.781812-4-maz@kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[johan: demote to KERN_DEBUG, rephrase messages, drop ftx-prog warning]
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that gpiolib can track the validity of GPIO pins, there is no need
to check whether the line is valid in request().
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201204164739.781812-5-maz@kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[johan: amend commit message]
Signed-off-by: Johan Hovold <johan@kernel.org>
Since it is pretty common for only some of the CBUS lines to be
valid as GPIO lines, let's report such validity to the rest of
the kernel.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201204164739.781812-3-maz@kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
usb_create_hcd will alloc memory for hcd, and we should
call usb_put_hcd to free it when adding fails to prevent
memory leak.
Fixes: b92a78e582 ("usb host: Oxford OXU210HP HCD driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201123145809.1456541-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have the nice helpers pr_err() and pr_warn(), use them instead
of raw printk().
Acked-by: Duncan Sands <duncan.sands@free.fr>
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Link: https://lore.kernel.org/r/20201208093206.24780-3-info@metux.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we already have the useful atm_info() macro, use it instead of
raw atm_printk()
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Link: https://lore.kernel.org/r/20201208093206.24780-2-info@metux.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an interface-number sanity check before testing the device flags to
avoid relying on undefined behaviour when left shifting in case a device
uses an interface number greater than or equal to BITS_PER_LONG (i.e. 64
or 32).
Reported-by: syzbot+8881b478dad0a7971f79@syzkaller.appspotmail.com
Fixes: c3a65808f0 ("USB: serial: option: reimplement interface masking")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This change adds vbus_vsafe0v which when set, makes TCPM
query for VSAFE0V by assigning the tcpc.is_vbus_vsafe0v callback.
Also enables ALERT.ExtendedStatus which is triggered when
status of EXTENDED_STATUS.vSafe0V changes.
EXTENDED_STATUS.vSafe0V is set when vbus is at vSafe0V and
cleared otherwise.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202040840.663578-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM at present lacks the notion of VSAFE0V. There
are three vbus threshold levels that are critical to track:
a. vSafe5V - VBUS “5 volts” as defined by the USB
PD specification.
b. vSinkDisconnect - Threshold used for transition from
Attached.SNK to Unattached.SNK.
c. vSafe0V - VBUS “0 volts” as defined by the USB
PD specification.
Tracking vSafe0V is crucial for entry into Try.SNK and
Attached.SRC and turning vbus back on by the source in
response to hard reset.
>From "4.5.2.2.8.2 Exiting from AttachWait.SRC State" section
in the Type-C spec:
"The port shall transition to Attached.SRC when VBUS is at
vSafe0V and the SRC.Rd state is detected on exactly one of
the CC1 or CC2 pins for at least tCCDebounce."
"A DRP that strongly prefers the Sink role may optionally
transition to Try.SNK instead of Attached.SRC when VBUS
is at vSafe0V and the SRC.Rd state is detected on exactly
one of the CC1 or CC2 pins for at least tCCDebounce."
>From "7.1.5 Response to Hard Resets" section in the PD spec:
"After establishing the vSafe0V voltage condition on VBUS,
the Source Shall wait tSrcRecover before re-applying VCONN
and restoring VBUS to vSafe5V."
vbus_present in the TCPM code tracks vSafe5V(vbus_present is true)
and vSinkDisconnect(vbus_present is false).
This change adds is_vbus_vsafe0v callback which when set makes
TCPM query for vSafe0V voltage level when needed.
Since not all TCPC controllers might have the capability
to report vSafe0V, TCPM assumes that vSafe0V is same as
vSinkDisconnect when is_vbus_vsafe0v callback is not set.
This allows TCPM to continue to support controllers which don't
have the support for reporting vSafe0V.
Introducing vSafe0V helps fix the failure reported at
"Step 15. CVS verifies PUT remains in AttachWait.SRC for 500ms"
of "TD 4.7.2 Try. SNK DRP Connect DRP Test" of
"Universal Serial Bus Type-C (USB Type-C) Functional Test
Specification Chapters 4 and 5". Here the compliance tester
intentionally maintains vbus at greater than vSafe0V and expects
the Product under test to stay in AttachWait.SRC till vbus drops
to vSafe0V.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202040840.663578-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_check_send_discover does not clear the send_discover flag
when any of the following conditions are not met.
1. data_role is TYPEC_HOST
2. link is pd_capable
Discovery indentity would anyways not be attempted during
the current session anymore when the above conditions are not
met. Hence clear the send_discover flag here to prevent
tcpm_enable_frs_work from rescheduling indefinetly.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201203031908.1491542-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nRetryCount was updated from 3 to 2 between PD2.0 and PD3.0 spec.
nRetryCount in "Table 6-34 Counter parameters" of the PD 2.0
spec is set to 3, whereas, nRetryCount in "Table 6-59 Counter
parameters" is set to 2.
Pass down negotiated rev in pd_transmit so that low level chip
drivers can update the retry count accordingly before attempting
packet transmission.
This helps in passing "TEST.PD.PORT.ALL.02" of the
"Power Delivery Merged" test suite which was initially failing
with "The UUT did not retransmit the message nReryCount times"
In fusb302 & tcpci drivers, by default the driver sets the retry
count to 3 (Default for PD 2.0). Update this to 2,
if the negotiated rev is PD 3.0.
In wcove, since the retry count is intentionally set to max, leaving
it as is.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202031733.647808-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Intel PMC Mux agent driver receives the response message from PMC, it
checks for the same response bits for all the mux states.
Corrected it by checking correct response message bits, Bit 8 & 9 for the
SAFE Mode and Alternate Modes and Bit 16 & 17 for the Connect and
Disconnect Modes.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20201203220813.16281-1-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm_runtime_enable will decrement the power disable depth. Imbalance
depth will resulted in enabling runtime PM of device fails later. Thus
a pairing decrement must be needed on the error handling path to keep it
balanced.
Fixes: 6c984b066d ("ARM: OMAP: USBHOST: Replace usbhs core driver APIs by Runtime pm APIs")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201123145719.1455849-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a USB2 device wakeup is not enabled/supported the link state may
still be in U0 in xhci_bus_suspend(), where it's then manually put
to suspended U3 state.
Just as with selective suspend the device needs time to enter U3
suspend before continuing with further suspend operations
(e.g. system suspend), otherwise we may enter system suspend with link
state in U0.
[commit message rewording -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Maple Ridge is successor of Titan Ridge Thunderbolt controller. As
Titan Ridge this one also includes xHCI host controller. In order to
safe energy we should put it to low power state by default when idle.
For this reason allow host runtime PM for Maple Ridge.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-5-mathias.nyman@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI controller on Alpine Ridge LP keeps the whole Thunderbolt
controller awake if the host controller is not allowed to sleep.
This is the case even if no USB devices are connected to the host.
Add the Intel Alpine Ridge LP product-id to the list of product-ids
for which we allow runtime PM by default.
Fixes: 2815ef7fe4 ("xhci-pci: allow host runtime PM as default for Intel Alpine and Titan Ridge")
Cc: <stable@vger.kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Synopsys xHC has an internal TRB cache of size TRB_CACHE_SIZE for
each endpoint. The default value for TRB_CACHE_SIZE is 16 for SS and 8
for HS. The controller loads and updates the TRB cache from the transfer
ring in system memory whenever the driver issues a start transfer or
update transfer command.
For chained TRBs, the Synopsys xHC requires that the total amount of
bytes for all TRBs loaded in the TRB cache be greater than or equal to 1
MPS. Or the chain ends within the TRB cache (with a last TRB).
If this requirement is not met, the controller will not be able to send
or receive a packet and it will hang causing a driver timeout and error.
This can be a problem if a class driver queues SG requests with many
small-buffer entries. The XHCI driver will create a chained TRB for each
entry which may trigger this issue.
This patch adds logic to the XHCI driver to detect and prevent this from
happening.
For every (TRB_CACHE_SIZE - 2), we check the total buffer size of
the SG list and if the last window of (TRB_CACHE_SIZE - 2) SG list length
and we don't make up at least 1 MPS, we create a temporary buffer to
consolidate full SG list into the buffer.
We check at (TRB_CACHE_SIZE - 2) window because it is possible that there
would be a link and/or event data TRB that take up to 2 of the cache
entries.
We discovered this issue with devices on other platforms but have not
yet come across any device that triggers this on Linux. But it could be
a real problem now or in the future. All it takes is N number of small
chained TRBs. And other instances of the Synopsys IP may have smaller
values for the TRB_CACHE_SIZE which would exacerbate the problem.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit uses the private data passed by parent device
to set the quirk for Synopsys xHC. This patch fixes the
SNPS xHC hang issue when the data is scattered across
small buffers which does not make atleast MPS size for
given TRB cache size of SNPS xHC.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-2-mathias.nyman@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- New phy drivers:
- Mediatek MT7621 PCIe PHY (promoted from staging)
- Ingenic USB phy driver supporting JZ4775 and X2000
- Intel Keem Bay USB PHY driver
- Marvell USB HSIC PHY driver supporting MMP3 SoC
- AXG MIPI D-PHY driver
- Updates:
- Conversion to YAML binding for:
- Broadcom SATA PHY
- Cadence Sierra PHY bindings
- STM32 USBC Phy
- Support for Exynos5433 PCIe PHY
- Support for Qualcomm SM8250 PCIe QMP PHY
- Support for Exynos5420 USB2 phy
- devm_platform_ioremap_resource conversion for bunch of drivers
-----BEGIN PGP SIGNATURE-----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=EFMp
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.11
- New phy drivers:
- Mediatek MT7621 PCIe PHY (promoted from staging)
- Ingenic USB phy driver supporting JZ4775 and X2000
- Intel Keem Bay USB PHY driver
- Marvell USB HSIC PHY driver supporting MMP3 SoC
- AXG MIPI D-PHY driver
- Updates:
- Conversion to YAML binding for:
- Broadcom SATA PHY
- Cadence Sierra PHY bindings
- STM32 USBC Phy
- Support for Exynos5433 PCIe PHY
- Support for Qualcomm SM8250 PCIe QMP PHY
- Support for Exynos5420 USB2 phy
- devm_platform_ioremap_resource conversion for bunch of drivers
* tag 'phy-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (72 commits)
drm/mediatek: avoid dereferencing a null hdmi_phy on an error message
phy: ingenic: depend on HAS_IOMEM
phy: mediatek: statify mtk_hdmi_phy_driver
dt-bindings: phy: Convert Broadcom SATA PHY to YAML
devicetree: phy: rockchip-emmc add output-tapdelay-select
phy: rockchip-emmc: output tap delay dt property
PHY: Ingenic: Add USB PHY driver using generic PHY framework.
dt-bindings: USB: Add bindings for Ingenic JZ4775 and X2000.
USB: PHY: JZ4770: Remove unnecessary function calls.
devicetree: phy: rockchip-emmc: pulldown property
phy: rockchip: set pulldown for strobe line in dts
phy: renesas: rcar-gen3-usb2: disable runtime pm in case of failure
phy: mediatek: allow compile-testing the hdmi phy
phy/rockchip: Make PHY_ROCKCHIP_INNO_HDMI depend on HAS_IOMEM to fix build error
phy: samsung: Merge Kconfig for Exynos5420 and Exynos5250
phy: ralink: phy-mt7621-pci: set correct name in MODULE_DEVICE_TABLE macro
phy: ralink: phy-mt7621-pci: drop 'COMPILE_TEST' from Kconfig
phy: mediatek: Make PHY_MTK_{XSPHY, TPHY} depend on HAS_IOMEM and OF_ADDRESS to fix build errors
phy: tegra: xusb: Fix usb_phy device driver field
phy: amlogic: replace devm_reset_control_array_get()
...
I got reports that some models of this old scanner need
this when using runtime PM.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201207130323.23857-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows downstream supplies and userspace to detect
whether external power is supplied.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/2c8e81d9da9ff05b065f66edba915edd11f74065.1607166657.git.agx@sigxcpu.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is more in line with what tcpm does and will be needed
to avoid recursive dependency like
> drivers/power/supply/Kconfig:2:error: recursive dependency detected!
drivers/power/supply/Kconfig:2: symbol POWER_SUPPLY is selected by TYPEC_TPS6598X
drivers/usb/typec/Kconfig:64: symbol TYPEC_TPS6598X depends on REGMAP_I2C
drivers/base/regmap/Kconfig:19: symbol REGMAP_I2C is selected by CHARGER_ADP5061
drivers/power/supply/Kconfig:93: symbol CHARGER_ADP5061 depends on POWER_SUPPLY
For a resolution refer to Documentation/kbuild/kconfig-language.rst
subsection "Kconfig recursive dependency limitations"
when selecting POWER_SUPPLY.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/6d11417c42d82caf66e08af160397959eb7d0d60.1607166657.git.agx@sigxcpu.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code is using the wrong sizeof() so it does not allocate enough
memory. It allocates 32 bytes but 72 are required. That will lead to
memory corruption.
Fixes: ae07809255 ("usb: mtu3: add debugfs interface files")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8ikqc4Mo2/0G72j@mwanda
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This error path
err_add_pdata:
for (i = 0; i < mod_data.num; i++)
kfree(dum[i]);
can be triggered when not all dum's elements are initialized.
Fix this by initializing all dum's elements to NULL.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://lore.kernel.org/r/1607063090-3426-1-git-send-email-minhquangbui99@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the i.MX6UL Errata document:
https://www.nxp.com/docs/en/errata/IMX6ULCE.pdf
ERR007881 also affects i.MX6UL, so pass the
CI_HDRC_DISABLE_DEVICE_STREAMING flag to workaround the issue.
Fixes: 52fe568e5d ("usb: chipidea: imx: add imx6ul usb support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201207020909.22483-2-peter.chen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new control-message helpers include a pipe-type check which is
almost completely redundant.
Control messages are generally sent to the default pipe which always
exists and is of the correct type since its endpoint representation is
created by USB core as part of enumeration for all devices.
There is currently only one instance of a driver in the tree which use
a control endpoint other than endpoint 0 (and it does not use the new
helpers).
Drivers should be testing for the existence of their resources at probe
rather than at runtime, but to catch drivers failing to do so USB core
already does a sanity check on URB submission and triggers a WARN().
Having the same sanity check done in the helper only suppresses the
warning without allowing us to find and fix the drivers.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20201204085110.20055-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "nregs" member is not used. The code uses the "regset.nregs"
struct member instead.
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8ikv1QA3Do50D+R@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -EREMOTEIO instead of -EINVAL on short control transfers when
using the new usb_control_msg_recv() helper.
EINVAL is used to report invalid arguments (e.g. to the helper) and
should not be used for unrelated errors.
Many driver currently return -EIO on short control transfers but since
host-controller drivers already use -EREMOTEIO for short transfers
whenever the URB_SHORT_NOT_OK flag is set, let's use that here as well.
This also allows usb_control_msg_recv() to eventually use
URB_SHORT_NOT_OK without changing the return value again.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20201204085110.20055-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A failure to send a complete control message is always an error so
there's no need to check for short transfers in usb_control_msg_send().
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20201204085110.20055-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code frees "mfi" and then derefences it on the next line to get
the error code.
Fixes: b0eec52fbe ("USB: apple-mfi-fastcharge: Fix kfree after failed kzalloc")
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X8ik4j8yJitVUyfU@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function may be unbound causing the ffs_ep and its descriptors
to be freed while userspace is in the middle of an ioctl requesting
the same descriptors. Avoid dangling pointer reference by first
making a local copy of desctiptors before releasing the spinlock.
Fixes: c559a35341 ("usb: gadget: f_fs: add ioctl returning ep descriptor")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201130203453.28154-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were a bunch of issues with the patch converting the
OMAP1 OSK board to use descriptors for controlling the USB
host:
- The chip label was incorrect
- The GPIO offset was off-by-one
- The code should use sleeping accessors
This patch tries to fix all issues at the same time.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 15d157e874 ("usb: ohci-omap: Convert to use GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201130083033.29435-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 0154012f80 as Hans
reports it causes problems on some systems. Until a "real" fix for this
can be found, revert this change to get normal functionality back.
Link: https://lore.kernel.org/r/70ca74c2-4a80-e25b-eca9-a63a75516673@redhat.com
Cc: Tom Yan <tom.ty89@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 558033c282 as Hans
reports it causes problems on some systems. Until a "real" fix for this
can be found, revert this change to get normal functionality back.
Link: https://lore.kernel.org/r/70ca74c2-4a80-e25b-eca9-a63a75516673@redhat.com
Cc: Tom Yan <tom.ty89@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5df7ef7d32 as Hans
reports it causes problems on some systems. Until a "real" fix for this
can be found, revert this change to get normal functionality back.
Link: https://lore.kernel.org/r/70ca74c2-4a80-e25b-eca9-a63a75516673@redhat.com
Cc: Tom Yan <tom.ty89@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a helper function to be used to configure flow control.
The flow-control code was the last caller that relied on the
memset-on-failure behaviour of cp210x_read_reg_block(), which we can now
drop in favour of bailing out on errors when retrieving the flow-control
settings.
This should also simplify adding support for software flow control.
Signed-off-by: Johan Hovold <johan@kernel.org>
Unlike other drivers cp210x have been retrieving the current terminal
settings from the device on open and reflecting those in termios.
Due to how set_termios() used to be implemented, this saved a few
control requests on open but has instead caused problems like broken
flow control and has required adding workarounds for swapped
line-control in cp2108 and line-speed initialisation on cp2104.
This unusual implementation also complicates adding new features for no
good reason.
Rip out the corresponding code and the above mentioned workarounds and
instead initialise the terminal settings unconditionally on open.
Signed-off-by: Johan Hovold <johan@kernel.org>
Update the line-control settings in one request unconditionally instead
of setting the word-length, parity and stop-bit settings separately.
This avoids multiple requests when several settings are changed even if
this scheme could potentially also be used to detect unsupported device
settings. Since all device types but CP2101 appears to support all
settings, let's handle that one specifically and also report back the
unsupported settings properly through termios by clearing the
corresponding bits.
Also drop the related unnecessary debug printks.
Signed-off-by: Johan Hovold <johan@kernel.org>
Return early from set_termios() in case no relevant terminal settings
have changed.
This avoids testing each parameter in turn and specifically allows the
line-control handling to be cleaned up further.
Signed-off-by: Johan Hovold <johan@kernel.org>
Here's a fix for a regression in the option driver which has been
backported to the stable trees and fix for a small memory leak on open
in the kl5kusb105 driver.
Included are also various new device ids.
All but the memleak fix has been in linux-next and with no reported
issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCX8oZqwAKCRALxc3C7H1l
CFNlAP0Q4S8ABcMrmFfWEDDbAxte3EH961IjDi4KpM02KMA9bwEArhDqvzSE+/FT
Cgm94pWu3YxhndQeZ3TuMFu76Z0g5Qs=
=0g5T
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.10-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.10-rc7
Here's a fix for a regression in the option driver which has been
backported to the stable trees and fix for a small memory leak on open
in the kl5kusb105 driver.
Included are also various new device ids.
All but the memleak fix has been in linux-next and with no reported
issues.
* tag 'usb-serial-5.10-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: kl5kusb105: fix memleak on open
USB: serial: ch341: sort device-id entries
USB: serial: ch341: add new Product ID for CH341A
USB: serial: option: fix Quectel BG96 matching
USB: serial: option: add support for Thales Cinterion EXS82
USB: serial: option: add Fibocom NL668 variants
Fix memory leak of control-message transfer buffer on successful open().
Fixes: 6774d5f532 ("USB: serial: kl5kusb105: fix open error path")
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
