Commit ea7dce901 ("drm/nv50/gr: print mpc trap name when it's not an mp
trap") added an nv_error call that was missing the priv parameter. This
causes GPFs if the error is ever hit.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Address of the ENG_RUNLIST register should be 0x002284 + (engine * 8),
not 0x002284 + (engine * 4).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
See https://bugs.freedesktop.org/show_bug.cgi?id=74492
Reported-by: Ronald <ronald645@gmail.com>
Suggested-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Since commit 0fa9061ae8 ("drm/nouveau/mc: handle irq-related setup
ourselves"), drm_device->irq_enabled remained unset. This is needed in
order to properly wait for a vblank event in the generic drm code.
See https://bugs.freedesktop.org/show_bug.cgi?id=74195
Reported-by: Jan Janecek <janjanjanx@gmail.com>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add DSB after icache flush to complete the cache maintenance operation.
Signed-off-by: Vinayak Kale <vkale@apm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We must use a 64-bit for this, otherwise overflowed bits get lost, and
that can result in a lower than intended value set.
Fixes: 8e0cb8a1f6 ("ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Fixes: 7d35496dd9 ("ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Tested-Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
since commit 89aef8921bf("ipv4: Delete routing cache."), the counter
in_slow_tot can't work correctly.
The counter in_slow_tot increase by one when fib_lookup() return successfully
in ip_route_input_slow(), but actually the dst struct maybe not be created and
cached, so we can increase in_slow_tot after the dst struct is created.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Ceph fixes from Sage Weil:
"We have some patches fixing up ACL support issues from Zheng and
Guangliang and a mount option to enable/disable this support. (These
fixes were somewhat delayed by the Chinese holiday.)
There is also a small fix for cached readdir handling when directories
are fragmented"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix __dcache_readdir()
ceph: add acl, noacl options for cephfs mount
ceph: make ceph_forget_all_cached_acls() static inline
ceph: add missing init_acl() for mkdir() and atomic_open()
ceph: fix ceph_set_acl()
ceph: fix ceph_removexattr()
ceph: remove xattr when null value is given to setxattr()
ceph: properly handle XATTR_CREATE and XATTR_REPLACE
Pull CIFS fixes from Steve French:
"Three cifs fixes, the most important fixing the problem with passing
bogus pointers with writev (CVE-2014-0069).
Two additional cifs fixes are still in review (including the fix for
an append problem which Al also discovered)"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Fix too big maxBuf size for SMB3 mounts
cifs: ensure that uncached writes handle unmapped areas correctly
[CIFS] Fix cifsacl mounts over smb2 to not call cifs
When FS-Cache allocates an object, the following sequence of events can
occur:
-->fscache_alloc_object()
-->cachefiles_alloc_object() [via cache->ops->alloc_object]
<--[returns new object]
-->fscache_attach_object()
<--[failed]
-->cachefiles_put_object() [via cache->ops->put_object]
-->fscache_object_destroy()
-->fscache_objlist_remove()
-->rb_erase() to remove the object from fscache_object_list.
resulting in a crash in the rbtree code.
The problem is that the object is only added to fscache_object_list on
the success path of fscache_attach_object() where it calls
fscache_objlist_add().
So if fscache_attach_object() fails, the object won't have been added to
the objlist rbtree. We do, however, unconditionally try to remove the
object from the tree.
Thanks to NeilBrown for finding this and suggesting this solution.
Reported-by: NeilBrown <neilb@suse.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: (a customer of) NeilBrown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This has been this way for years, and every time I stumble across it I
lose my lunch. After coming across it for the nth time in the Coverity
results, I had to overcome the bystander effect and do something about
it.
This ignores the 79 column limit in favor of making it look like C
instead of gibberish.
The correct thing to do here would be to lose some of the indentation by
breaking this function up into several smaller ones. I might do that at
some point if I have the stomach to look at this again.
(Also some of those overlong ternary operations would likely be more
readable as regular if's)
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Issuing set_termios() from irtty_close() causes kernel Oops for
unplugged usb-serial devices.
Since no other tty_ldisc calls set_termios() on close and no tty driver
seem to check if tty->device_data is NULL or not on entry to set_termios(),
the only solution I can come up with is to remove the irtty_stop_receiver()
call, which only updates termios.
Signed-off-by: Tommie Gannert <tommie@gannert.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull AVR32 fixes from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: add generic vga.h to Kbuild
avr32: add generic ioremap_wc() definition in io.h
avr32: Makefile: add '-D__linux__' flag for gcc-4.4.7 use
avr32: fix missing module.h causing build failure in mimc200/fram.c
If directory is fragmented, readdir() read its dirfrags one by one.
After reading all dirfrags, the corresponding dentries are sorted in
(frag_t, off) order in the dcache. If dentries of a directory are all
cached, __dcache_readdir() can use the cached dentries to satisfy
readdir syscall. But when checking if a given dentry is after the
position of readdir, __dcache_readdir() compares numerical value of
frag_t directly. This is wrong, it should use ceph_frag_compare().
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Make the 'acl' option dependent on having ACL support compiled in. Make
the 'noacl' option work even without it so that one can always ask it to
be off and not error out on mount when it is not supported.
Signed-off-by: Guangliang Zhao <lucienchao@gmail.com>
Signed-off-by: Sage Weil <sage@inktank.com>
If acl is equivalent to file mode permission bits, ceph_set_acl()
needs to remove any existing acl xattr. Use __ceph_setxattr() to
handle both setting and removing acl xattr cases, it doesn't return
-ENODATA when there is no acl xattr.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
For the setxattr request, introduce a new flag CEPH_XATTR_REMOVE
to distinguish null value case from the zero-length value case.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
return -EEXIST if XATTR_CREATE is set and xattr alread exists.
return -ENODATA if XATTR_REPLACE is set but xattr does not exist.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Pull powerpc fixes from Ben Herrenschmidt:
"Here are some more powerpc fixes for 3.14
The main one is a nasty issue with the NUMA balancing support which
requires a small generic change and the addition of a new accessor to
set _PAGE_NUMA. Both have been reviewed and acked by Mel and Rik.
The changelog should have plenty of details but basically, without
this fix, we get random user segfaults and/or corruptions due to
missing TLB/hash flushes. Aneesh series of 3 patches fixes it.
We have some vDSO vs. perf fixes from Anton, some small EEH fixes
from Gavin, a ppc32 regression vs the stack overflow detector, and a
fix for the way we handle PCIe host bridge speed settings on pseries
(which is needed for proper operations of AMD graphics cards on
Power8)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/eeh: Disable EEH on reboot
powerpc/eeh: Cleanup on eeh_subsystem_enabled
powerpc/powernv: Rework EEH reset
powerpc: Use unstripped VDSO image for more accurate profiling data
powerpc: Link VDSOs at 0x0
mm: Use ptep/pmdp_set_numa() for updating _PAGE_NUMA bit
mm: Dirty accountable change only apply to non prot numa case
powerpc/mm: Add new "set" flag argument to pte/pmd update function
powerpc/pseries: Add Gen3 definitions for PCIE link speed
powerpc/pseries: Fix regression on PCI link speed
powerpc: Set the correct ksp_limit on ppc32 when switching to irq stack
This is not a buffer overflow in the traditional sense: we don't
overflow any *kernel* buffers, but we do mis-count the amount of data we
copy back to user space for the SYSLOG_ACTION_READ_ALL case.
In particular, if the user buffer is too small to hold everything, and
*if* there is a continuation line at just the right place, we can end up
giving the user more data than he asked for.
The reason is that we first count up the number of bytes all the log
records contains, then we walk the records again until we've skipped the
records at the beginning that won't fit, and then we walk the rest of
the records and copy them to the user space buffer.
And in between that "skip the initial records that won't fit" and the
"copy the records that *will* fit to user space", we reset the 'prev'
variable that contained the record information for the last record not
copied. That meant that when we started copying to user space, we now
had a different character count than what we had originally calculated
in the first record walk-through.
The fix is to simply not clear the 'prev' flags value (in both cases
where we had the same logic: syslog_print_all and kmsg_dump_get_buffer:
the latter is used for pstore-like dumping)
Reported-and-tested-by: Debabrata Banerjee <dbanerje@akamai.com>
Acked-by: Kay Sievers <kay@vrfy.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need at least HID_MAX_BUFFER_SIZE (4096) bytes as input buffer. HID
core depends on this as it requires every input report to be at least as
big as advertised.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID core expects the input buffers to be at least of size 4096
(HID_MAX_BUFFER_SIZE). Other sizes will result in buffer-overflows if an
input-report is smaller than advertised. We could, like i2c, compute the
biggest report-size instead of using HID_MAX_BUFFER_SIZE, but this will
blow up if report-descriptors are changed after ->start() has been called.
So lets be safe and just use the biggest buffer we have.
Note that this adds an additional copy to the HIDP input path. If there is
a way to make sure the skb-buf is big enough, we should use that instead.
The best way would be to make hid-core honor the @size argument, though,
that sounds easier than it is. So lets just fix the buffer-overflows for
now and afterwards look for a faster way for all transport drivers.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
aggregator_identifier is used to assign unique aggregator identifiers
to aggregators of a bond during device enslaving.
aggregator_identifier is currently a global variable that is zeroed in
bond_3ad_initialize().
This sequence will lead to duplicate aggregator identifiers for eth1 and eth3:
create bond0
change bond0 mode to 802.3ad
enslave eth0 to bond0 //eth0 gets agg id 1
enslave eth1 to bond0 //eth1 gets agg id 2
create bond1
change bond1 mode to 802.3ad
enslave eth2 to bond1 //aggregator_identifier is reset to 0
//eth2 gets agg id 1
enslave eth3 to bond0 //eth3 gets agg id 2
Fix this by making aggregator_identifier private to the bond.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a generic hard_header_len check from the usbnet
module that is causing dropped packages under certain circumstances
for devices that send rx packets that cross urb boundaries.
One example is the AX88772B which occasionally send rx packets that
cross urb boundaries where the remaining partial packet is sent with
no hardware header. When the buffer with a partial packet is of less
number of octets than the value of hard_header_len the buffer is
discarded by the usbnet module.
With AX88772B this can be reproduced by using ping with a packet
size between 1965-1976.
The bug has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=29082
This patch introduces the following changes:
- Removes the generic hard_header_len check in the rx_complete
function in the usbnet module.
- Introduces a ETH_HLEN check for skbs that are not cloned from
within a rx_fixup callback.
- For safety a hard_header_len check is added to each rx_fixup
callback function that could be affected by this change.
These extra checks could possibly be removed by someone
who has the hardware to test.
- Removes a call to dev_kfree_skb_any() and instead utilizes the
dev->done list to queue skbs for cleanup.
The changes place full responsibility on the rx_fixup callback
functions that clone skbs to only pass valid skbs to the
usbnet_skb_return function.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug was reported by Steinar H. Gunderson and was introduced by commit
f7cb888633 ("sit/gre6: don't try to add the same route two times").
root@morgental:~# ip tunnel add foo mode gre remote 1.2.3.4 ttl 64
root@morgental:~# ip link set foo up mtu 1468
root@morgental:~# ip -6 route show dev foo
fe80::/64 proto kernel metric 256
but after the above commit, no such route shows up.
There is no link local route because dev->dev_addr is 0 (because local ipv4
address is 0), hence no link local address is configured.
In this scenario, the link local address is added manually: 'ip -6 addr add
fe80::1 dev foo' and because prefix is /128, no link local route is added by the
kernel.
Even if the right things to do is to add the link local address with a /64
prefix, we need to restore the previous behavior to avoid breaking userpace.
Reported-by: Steinar H. Gunderson <sesse@samfundet.no>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
batadv_send_skb_prepare_unicast(_4addr) might reallocate the
skb's data. If it does then our ethhdr pointer is not valid
anymore in batadv_send_skb_unicast(), resulting in a kernel
paging error.
Fixing this by refetching the ethhdr pointer after the
potential reallocation.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
In the failure path of the orig_node initialization routine
the orig_node->bat_iv.bcast_own field is free'd twice: first
in batadv_iv_ogm_orig_get() and then later in
batadv_orig_node_free_rcu().
Fix it by removing the kfree in batadv_iv_ogm_orig_get().
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
When the TVLV parsing routine succeed the skb is left
untouched thus leading to a memory leak.
Fix this by consuming the skb in case of success.
Introduced by ef26157747
("batman-adv: tvlv - basic infrastructure")
Reported-by: Russel Senior <russell@personaltelco.net>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Tested-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
When computing the CRC on a 2byte variable the order of
the bytes obviously alters the final result. This means
that computing the CRC over the same value on two archs
having different endianess leads to different numbers.
The global and local translation table CRC computation
routine makes this mistake while processing the clients
VIDs. The result is a continuous CRC mismatching between
nodes having different endianess.
Fix this by converting the VID to Network Order before
processing it. This guarantees that every node uses the same
byte order.
Introduced by 7ea7b4a142
("batman-adv: make the TT CRC logic VLAN specific")
Reported-by: Russel Senior <russell@personaltelco.net>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Tested-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Since batadv_orig_node_new() sets the refcount to two, assuming that
the calling function will use a reference for putting the orig_node into
a hash or similar, both references must be freed if initialization of
the orig_node fails. Otherwise that object may be leaked in that error
case.
Reported-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
When adding a new neighbour it is important to atomically
perform the following:
- check if the neighbour already exists
- append the neighbour to the proper list
If the two operations are not performed in an atomic context
it is possible that two concurrent insertions add the same
neighbour twice.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
pskb_may_pull() returns 1 on success and 0 in case of failure,
therefore checking for the return value being negative does
not make sense at all.
This way if the function fails we will probably read beyond the current
skb data buffer. Fix this by doing the proper check.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
There is a refcounter unbalance in the CRC checking routine
invoked on OGM reception. A vlan object is retrieved (thus
its refcounter is increased by one) but it is never properly
released. This leads to a memleak because the vlan object
will never be free'd.
Fix this by releasing the vlan object after having read the
CRC.
Reported-by: Russell Senior <russell@personaltelco.net>
Reported-by: Daniel <daniel@makrotopia.org>
Reported-by: cmsv <cmsv@wirelesspt.net>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
When accessing a TT-TVLV container in the OGM RX path
the variable pointing to the list of changes to apply is
altered by mistake.
This makes the TT component read data at the wrong position
in the OGM packet buffer.
Fix it by removing the bogus pointer alteration.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The current MTU computation always returns a value
smaller than 1500bytes even if the real interfaces
have an MTU large enough to compensate the batman-adv
overhead.
Fix the computation by properly returning the highest
admitted value.
Introduced by a19d3d85e1
("batman-adv: limit local translation table max size")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Added STM sensor hub vendor id in HID_SENSOR_HUB_ENUM_QUIRK to
fix report descriptors. These devices uses old FW which uses
logical 0 as minimum. In these, HID reports are not using proper
collection classes. So we need to fix report descriptors,for
such devices. This will not have any impact, if the FW uses
logical 1 as minimum.
We look for usage id for "power and report state", and modify
logical minimum value to 1.
This is a follow-up patch to commit id 875e36f8.
Signed-off-by: Archana Patni <archana.patni@linux.intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Need add generic "vga.h", or can not pass building for allmodconfig,
the related error:
CC [M] drivers/gpu/drm/drm_irq.o
In file included from include/linux/vgaarb.h:34,
from drivers/gpu/drm/drm_irq.c:42:
include/video/vga.h:22:21: error: asm/vga.h: No such file or directory
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
Need generic ioremap_wc(), or can not pass compiling with allmodconfig,
the related error:
CC [M] drivers/gpu/drm/drm_bufs.o
drivers/gpu/drm/drm_bufs.c: In function 'drm_addmap_core':
drivers/gpu/drm/drm_bufs.c:217: error: implicit declaration of function 'ioremap_wc'
drivers/gpu/drm/drm_bufs.c:218: warning: assignment makes pointer from integer without a cast
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
For avr32 cross compiler, do not define '__linux__' internally, so it
will cause issue with allmodconfig.
The related error:
CC [M] fs/coda/psdev.o
In file included from include/linux/coda.h:64,
from fs/coda/psdev.c:45:
include/uapi/linux/coda.h:221: error: expected specifier-qualifier-list before 'u_quad_t'
The related toolchain version (which only download, not re-compile):
[root@gchen linux-next]# /upstream/toolchain/download/avr32-gnu-toolchain-linux_x86/bin/avr32-gcc -v
Using built-in specs.
Target: avr32
Configured with: /data2/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/src/gcc/configure --target=avr32 --host=i686-pc-linux-gnu --build=x86_64-pc-linux-gnu --prefix=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --enable-languages=c,c++ --disable-nls --disable-libssp --disable-libstdcxx-pch --with-dwarf2 --enable-version-specific-runtime-libs --disable-shared --enable-doc --with-mpfr-lib=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86/lib --with-mpfr-include=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86/include --with-gmp=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --with-mpc=/home/toolsbuild/jenkins-knuth/workspace/avr32-gnu-toolchain/avr32-gnu-toolchain-linux_x86 --enable-__cxa_atexit --disable-shared --with-newlib --with-pkgversion=AVR_32_bit_GNU_Toolchain_3.4.2_435 --with-bugurl=http://www
.atmel.com/avr
Thread model: single
gcc version 4.4.7 (AVR_32_bit_GNU_Toolchain_3.4.2_435)
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Hans-Christian Egtvedt <hegtvedt@cisco.com>
Cc: stable@vger.kernel.org
Causing this:
In file included from arch/avr32/boards/mimc200/fram.c:13:
include/linux/miscdevice.h:51: error: field 'list' has incomplete type
include/linux/miscdevice.h:55: error: expected specifier-qualifier-list before 'mode_t'
arch/avr32/boards/mimc200/fram.c:42: error: 'THIS_MODULE' undeclared here (not in a function)
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: stable@vger.kernel.org
Mathias reported that on an AMD Geode LX embedded board (ALiX)
with ath9k driver PACKET_QDISC_BYPASS, introduced in commit
d346a3fae3 ("packet: introduce PACKET_QDISC_BYPASS socket
option"), triggers a WARN_ON() coming from the driver itself
via 066dae93bd ("ath9k: rework tx queue selection and fix
queue stopping/waking").
The reason why this happened is that ndo_select_queue() call
is not invoked from direct xmit path i.e. for ieee80211 subsystem
that sets queue and TID (similar to 802.1d tag) which is being
put into the frame through 802.11e (WMM, QoS). If that is not
set, pending frame counter for e.g. ath9k can get messed up.
So the WARN_ON() in ath9k is absolutely legitimate. Generally,
the hw queue selection in ieee80211 depends on the type of
traffic, and priorities are set according to ieee80211_ac_numbers
mapping; working in a similar way as DiffServ only on a lower
layer, so that the AP can favour frames that have "real-time"
requirements like voice or video data frames.
Therefore, check for presence of ndo_select_queue() in netdev
ops and, if available, invoke it with a fallback handler to
__packet_pick_tx_queue(), so that driver such as bnx2x, ixgbe,
or mlx4 can still select a hw queue for transmission in
relation to the current CPU while e.g. ieee80211 subsystem
can make their own choices.
Reported-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow users to invoke netdev_cap_txqueue, it needs to
be moved into netdevice.h header file. While at it, also add kernel
doc header to document the API.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
