When using e.g. bonding, and doing a sequence such as
# iw wlan0 set type __ap
# ip link add name bond1 type bond
# ip link set wlan0 master bond1
# iw wlan0 interface del
we deadlock, since the wlan0 interface removal will cause
bonding to reset the MAC address of wlan0.
The locking would be somewhat difficult to fix, but since
this only happens during removal, we can simply ignore the
MAC address change at this time.
Reported-by: syzbot+25b3a0b24216651bc2af@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20231012123447.9f9d7fd1f237.Ic3a5ef4391b670941a69cec5592aefc79d9c2890@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, we have a per-link debugfs directory which contains the
per-link files. In case of non-MLO we would like to put the per-link
files in the netdev directory to keep it how it was before MLO.
- Upon interface creation the netdev will be created with the per-link
files in it.
- Upon switching to MLO: delete the entire netdev directory and then
recreate it without the per-link files. Then the per-link directories
with the per-link files in it will be created in ieee80211_link_init()
- Upon switching to non-MLO: delete the entire netdev directory
(including the per-link directories) and recreate it with the per-link
files in it.
Note that this also aligns to always call the vif link debugfs
method for the deflink as promised in the documentation, which
wasn't done before.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.082e698caca9.I5bef7b2026e0f58b4a958b3d1f459ac5baeccfc9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently call ieee80211_txq_teardown_flows() as part
of ieee80211_remove_interfaces(), but that's not really
right in case of HW registration failures, specifically
rate control. Call it separately to fix that issue.
Reported-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we're now protecting everything with the wiphy mutex
(and were really using it for almost everything before),
there's no longer any real reason to have a separate wdev
mutex. It may feel better, but really has no value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the iflist_mtx, so we don't need this mutex any
more in mac80211. However, drivers may also iterate,
and in some cases (e.g. mt76) do so from high-priority
contexts. Thus, keep the mutex around but remove its
usage in mac80211 apart from those driver-visible parts
that are still needed.
Most of this change was done automatically with spatch,
with the parts that are still needed as described above
reverted manually.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the local->mtx, so we don't need this mutex any
more. Remove it.
Most of this change was done automatically with spatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the chanctx_mtx, so we don't need this mutex any
more. Remove it.
Most of this change was done automatically with spatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the key_mtx, so we don't need this mutex any
more. Remove it.
Most of this change was done automatically with spatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the sta_mtx, so we don't need this mutex any
more. Remove it.
Most of this change was done automatically with spatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We want to ensure everything holds the wiphy lock,
so also extend that to the MAC change callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We want to extend the wiphy locking to the interface list,
so move that into the section locked with the wiphy lock.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We want to replace the locking in mac80211 by just the wiphy
mutex, so hold the lock here around concurrency checks for
the future where the chanctx_mtx used inside goes away.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Again this should be per link and will get cancellation
issues, move it to a wiphy work.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This work should be made per link as well, and then
will have cancellation issues. Moving it to a wiphy
work already fixes those beforehand.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This again is intended for future cleanups that are
possible when mac80211 and drivers can assume the
wiphy is locked.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This way we hold the wiphy mutex there, as a step towards
removing some of the additional locks we have.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Along with everything else, move the dynamic PS work
to be a wiphy work, to simplify locking later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Lock the wiphy in the IP address notifier as another
place that should have it locked before calling into
the driver. This needs a bit of attention since the
notifier can be called while the wiphy is already
locked, when we remove an interface. Handle this by
not running the notifier in this case, and instead
calling out to the driver directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the scan work to wiphy work, which also simplifies
the way we handle the work vs. the scan configuration.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the DFS CAC work over to hold the wiphy lock
there without worry about work cancellation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current SMPS status handling isn't per link, so we only
ever change the deflink, which is obviously wrong, it's not
even used for multi-link connections, but the request API
actually includes the link ID.
Use the new status_data changes to move the handling to the
right link, this also saves parsing the frame again on the
status report, instead we can now check only if it was an
SMPS frame.
Of course, move the worker to be a wiphy work so that we're
able to cancel it safely for the link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to all the multi-link handling, we now expose the fact that
the sdata/vif is locked to drivers, e.g. when the driver uses
ieee80211_set_monitor_channel(). This was true when a chanctx
is added to or removed from a link, _except_ in monitor mode
with the virtual sdata/vif. Change that, so that drivers can
make that assumption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230619161906.a5cf7534beda.I5b51664231abee27e02f222083df7ccf88722929@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As a preparation to support disabled/dormant links, add the
following function:
- ieee80211_vif_usable_links(): returns the bitmap of the links
that can be activated. Use this function in all the places that
the bitmap of the usable links is needed.
- ieee80211_vif_is_mld(): returns true iff the vif is an MLD.
Use this function in all the places where an indication that the
connection is a MLD is needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230608163202.86e3351da1fc.If6fe3a339fda2019f13f57ff768ecffb711b710a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we want to have wiphy_lock() for the unregistration
in the future, unregister also netdevs via cfg80211 now
to be able to hold the wiphy_lock() for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll need this later to convert other works that might
be cancelled from here, so convert this one first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we have a reconfig failure in the driver, then we need
to shut down the network interface(s) at the network stack
level through cfg80211, which can result in a lot of those
"Failed check-sdata-in-driver check, ..." warnings, since
interfaces are considered to not be in the driver when the
reconfiguration fails, but we still need to go through all
the shutdown flow.
Avoid many of these warnings by storing the fact that the
stack experienced a reconfiguration failure and not doing
the warning in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.3750c4ae6e76.I9e80d6026f59263c008a1a68f6cd6891ca0b93b0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On newer MediaTek SoCs (e.g. MT7986), WLAN->WLAN or WLAN->Ethernet flows can
be offloaded by the SoC. In order to support that, the .ndo_setup_tc op is
needed.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230321091248.30947-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of preventing adding AP_VLAN to MLO enabled APs, this check was
preventing adding more than one 4-addr AP_VLAN regardless of the MLO status.
Fix this by adding missing extra checks.
Fixes: ae960ee90b ("wifi: mac80211: prevent VLANs on MLDs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20221214130326.37756-1-nbd@nbd.name
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be used to selectively disable feature flags for checksum offload,
scatter/gather or GSO by changing vif->netdev_features.
Removing features from vif->netdev_features does not affect the netdev
features themselves, but instead fixes up skbs in the tx path so that the
offloads are not needed in the driver.
Aside from making it easier to deal with vif type based hardware limitations,
this also makes it possible to optimize performance on hardware without native
GSO support by declaring GSO support in hw->netdev_features and removing it
from vif->netdev_features. This allows mac80211 to handle GSO segmentation
after the sta lookup, but before itxq enqueue, thus reducing the number of
unnecessary sta lookups, as well as some other per-packet processing.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20221010094338.78070-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The call to ieee80211_do_stop() right after will also do
synchronize_rcu() to ensure the SDATA_STATE_RUNNING bit
is cleared, so we don't need to synchronize_net() here.
Change-Id: Id9f9ffcf195002013e5d9fde288877d219780864
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All drivers are now using mac80211 internal queues (iTXQs).
Drop mac80211 internal support for the old push path.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Properly handle TX stop for internal queues (iTXQs) within mac80211.
mac80211 must not stop netdev queues when using mac80211 iTXQs.
For these drivers the netdev interface is created with IFF_NO_QUEUE.
While netdev still drops frames for IFF_NO_QUEUE interfaces when we stop
the netdev queues, it also prints a warning when this happens:
Assuming the mac80211 interface is called wlan0 we would get
"Virtual device wlan0 asks to queue packet!" when netdev has to drop a
frame.
This patch is keeping the harmless netdev queue starts for iTXQ drivers.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unlock before returning -EOPNOTSUPP.
Fixes: 3c06e91b40 ("wifi: mac80211: Support POWERED_ADDR_CHANGE feature")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement an API function and debugfs file to switch
active links.
Also provide an async version of the API so drivers
can call it in arbitrary contexts, e.g. while in the
authorized callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We probably should've done that originally, we already have
about 300 lines of code there, and will add more. Move all
the link code we wrote to a new file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adds support in mac80211 for NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE.
The motivation behind this functionality is to fix limitations of
address randomization on frequencies which are disallowed in world
roaming.
The way things work now, if a client wants to randomize their address
per-connection it must power down the device, change the MAC, and
power back up. Here lies a problem since powering down the device
may result in frequencies being disabled (until the regdom is set).
If the desired BSS is on one such frequency the client is unable to
connect once the phy is powered again.
For mac80211 based devices changing the MAC while powered is possible
but currently disallowed (-EBUSY). This patch adds some logic to
allow a MAC change while powered by removing the interface, changing
the MAC, and adding it again. mac80211 will advertise support for
this feature so userspace can determine the best course of action e.g.
disallow address randomization on certain frequencies if not
supported.
There are certain limitations put on this which simplify the logic:
- No active connection
- No offchannel work, including scanning.
Signed-off-by: James Prestwood <prestwoj@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement key installation and lookup (on TX and RX)
for MLO, so we can use multiple GTKs/IGTKs/BIGTKs.
Co-authored-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For an AP interface, set the link BSSID when the link
is initialized.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During the code reshuffling, I accidentally set this to
NULL before using it, fix that to fix the link data leak.
Fixes: d3e2439b0f ("wifi: mac80211: fix link manipulation")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
lockdep complains use of uninitialized spinlock at ieee80211_do_stop() [1],
for commit f856373e2f ("wifi: mac80211: do not wake queues on a vif
that is being stopped") guards clear_bit() using fq.lock even before
fq_init() from ieee80211_txq_setup_flows() initializes this spinlock.
According to discussion [2], Toke was not happy with expanding usage of
fq.lock. Since __ieee80211_wake_txqs() is called under RCU read lock, we
can instead use synchronize_rcu() for flushing ieee80211_wake_txqs().
Link: https://syzkaller.appspot.com/bug?extid=eceab52db7c4b961e9d6 [1]
Link: https://lkml.kernel.org/r/874k0zowh2.fsf@toke.dk [2]
Reported-by: syzbot <syzbot+eceab52db7c4b961e9d6@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: f856373e2f ("wifi: mac80211: do not wake queues on a vif that is being stopped")
Tested-by: syzbot <syzbot+eceab52db7c4b961e9d6@syzkaller.appspotmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/9cc9b81d-75a3-3925-b612-9d0ad3cab82b@I-love.SAKURA.ne.jp
When we add non-deflink pointers, we need to remove the
link[0] pointer to deflink in case link[0] is not valid
afterwards. Also, we need to add that back when there
are no more valid links. Reorg the code to fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
