Aquantia PHYs used on platforms such as T2080RDB, T1024RDB.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The PHY uses XAUI interface to connect to MAC, mostly the PHY used on
riser card.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds a few optimisations in memcpy functions by using
lbzu/stbu instead of lxb/stb and by re-ordering insn inside a loop
to reduce latency due to loading
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
cacheable_memcpy uses dcbz instruction and is more efficient than
memcpy when the destination is in RAM. If the destination is in an
io area, memcpy_toio() is normally used, not memcpy
This patch renames memcpy as generic_memcpy, and renames
cacheable_memcpy as memcpy
On MPC885, we get approximatly 7% increase of the transfer rate
on an FTP reception
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
cacheable_memzero() which has become the new memset() and the old
memset() are quite similar, so just merge them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
cacheable_memzero uses dcbz instruction and is more efficient than
memset(0) when the destination is in RAM
This patch renames memset as generic_memset, and defines memset
as a prolog to cacheable_memzero. This prolog checks if the byte
to set is 0. If not, it falls back to generic_memcpy()
cacheable_memzero disappears as it is not referenced anywhere anymore
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This partially reverts
commit 'powerpc: Remove duplicate cacheable_memcpy/memzero functions
("b05ae4ee602b7dc90771408ccf0972e1b3801a35")'
Functions cacheable_memcpy/memzero are more efficient than
memcpy/memset as they use the dcbz instruction which avoids refill
of the cacheline with the data that we will overwrite.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
CPM muram is not cached, so use memset_io() instead of memset()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
__flush_dcache_icache_phys() requires the ability to access the
memory with the MMU disabled, which means that on a 32-bit system
any memory above 4 GiB is inaccessible. In particular, mpc86xx is
32-bit and can have more than 4 GiB of RAM.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The C version of csum_add() as defined in include/net/checksum.h gives
the following assembly in ppc32:
0: 7c 04 1a 14 add r0,r4,r3
4: 7c 64 00 10 subfc r3,r4,r0
8: 7c 63 19 10 subfe r3,r3,r3
c: 7c 63 00 50 subf r3,r3,r0
and the following in ppc64:
0xc000000000001af8 <+0>: add r3,r3,r4
0xc000000000001afc <+4>: cmplw cr7,r3,r4
0xc000000000001b00 <+8>: mfcr r4
0xc000000000001b04 <+12>: rlwinm r4,r4,29,31,31
0xc000000000001b08 <+16>: add r3,r4,r3
0xc000000000001b0c <+20>: clrldi r3,r3,32
0xc000000000001b10 <+24>: blr
include/net/checksum.h also offers the possibility to define an arch
specific function. This patch provides a specific csum_add() inline
function.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
csum_tcpudp_magic() is only a few instructions, and does modify
really few registers. So it is not worth having it as a separate
function and suffer function branching and saving of volatile
registers.
This patch makes it inline by use of the already existing
csum_tcpudp_nofold() function.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Unify mpc85xx and corenet configs using fragments, to ease maintenance
and avoid the sort of drift that the previous patch fixed.
Hardware and software options are separated, with the hope that other
embedded platforms could share the software options, and to make it
easier to maintain custom/alternate configs that focus on either
hardware or software options.
Due to the previous patch, this patch should not affect the results of
any of the affected defconfigs -- only how those results are achieved.
The resulting config is more or less the union of the options that any
of the configs previously selected. No attempt was made in this (or
the previous) patch to edit out questionable options, but this patch
will make it easier to do so in future patches.
Signed-off-by: Scott Wood <scottwood@freescale.com>
The mpc85xx and corenet configs have many differences between them that
can't be explained by the target hardware of each config. The next
patch will consolidate these targets using kconfig fragments; this
patch shows what the resulting defconfigs will look like (generated by
using savedefconfig on a fragment-generated config).
Signed-off-by: Scott Wood <scottwood@freescale.com>
corenet32_smp_defconfig is missing some things that modern distros
require, enable them.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Scott Wood <scottwood@freescale.com>
By default we enable DMA(CONFIG_FSL_DMA) support
which are needed on P2041RDB, P3041DS, P4080DS,
B4860QDS, etc.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When detecting EEH error on non-existing PE, including the reserved
one, the PE is simply unfrozen without dumping the PHB diag-data,
which is useful for locating the root cause of the EEH error. The
patch dumps the PHB diag-data when non-existing PE reports error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On LE kernel, the non-existing PE number in BE format derived from
skiboot firmware isn't converted to LE format properly as following
kernel log indicates:
EEH: Clear non-existing PHB#4-PE#200000000000000
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds one helper function 'sigcontext_vmx_regs' which computes
quad word aligned pointer for 'vmx_reserve' array element in sigcontext
structure making the code more readable.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Reword comment and fix build for CONFIG_ALTIVEC=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit ce48b21007 "powerpc: Add VSX context save/restore, ptrace and
signal support" expanded the 'vmx_reserve' array element to contain 101
double words, but the comment block above was not updated.
Also reorder the constants in the array size declaration to reflect the
logic mentioned in the comment block above. This change helps in
explaining how the HW registers are represented in the array. But no
functional change.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Reworded change log and added whitespace around +'s]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently tm_orig_msr is getting used during process context switch only.
Then there is ckpt_regs which saves the checkpointed userspace context
The MSR slot contained in ckpt_regs structure can be used during process
context switch instead of tm_orig_msr, thus allowing us to drop it from
thread_struct structure. This patch does that change.
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds support for OPAL EPOW (Environmental and Power Warnings)
and DPO (Delayed Power Off) events for the PowerNV platform. These events
are generated on FSP (Flexible Service Processor) based systems. EPOW
events are generated due to various critical system conditions that
require system shutdown. A few examples of these conditions are high
ambient temperature or system running on UPS power with low UPS battery.
DPO event is generated in response to admin initiated system shutdown
request. Upon receipt of EPOW and DPO events the host kernel invokes
orderly_poweroff() for performing graceful system shutdown.
Signed-off-by: Vipin K Parashar <vipin@linux.vnet.ibm.com>
Acked-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When releasing PE for SRIOV VF, the PE is forced to be frozen
wrongly. When the same PE is picked for another VF, it won't
work anyhow. The patch fixes the issue by unfreezing, not
freezing the VF PE when releasing it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PELTV of PF PE should include VF PE, which is missed by current
code, so that the VF PE is frozen automatically when freezing PF PE.
The patch fixes the PELTV of PF PE to include VF PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On PHB3, PE might be reserved in advance to reflect the M64 segments
consumed by the PE according to M64 BARs (exclude VF BARs) of the PCI
devices included in the PE. The PE is picked based on M64 BARs instead
of the bridge's M64 windows, which might include VF BARs. Otherwise,
wrong PE could be picked.
The patch calculates the used M64 segments and PE numbers according to
the M64 BARs, excluding VF BARs, of PCI devices in one particular PE,
instead of the bridge's M64 windows. Then the right PE number is picked.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch changes the type of last argument of pnv_ioda_setup_bus_PE()
and phb::pick_m64_pe() to boolean. No functional change.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On PHB3, some PEs might be reserved in advance to reflect the M64
segments consumed by those PEs. We're reserving PEs based on the
M64 window of root port, which might contain VF BAR. The PEs for
VFs are allocated dynamically, not reserved based on the consumed
M64 segments. So the M64 window of root port isn't reliable for
the task. Instead, we go through M64 BARs (VF BARs excluded) of
PCI devices under the specified root bus and reserve PEs accordingly,
as the patch does.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PE numbers are reserved according to root port's M64 window,
which is aligned to M64 segment finely. So one PE shouldn't be
reserved for multiple times. We will reserve PE numbers according
to the M64 BARs of PCI device in subsequent patches, which aren't
aligned to M64 segment size finely. It means one particular PE
could be reserved for multiple times.
The patch allows one PE to be reserved for multiple times and we
print the warning message at debugging level.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
mtmsr() does the right thing on 32bit and 64bit, so use it everywhere.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The encoding of the lengths in the ibm_architecture_vec array is
"interesting" to say the least. It's non-obvious how the number of bytes
we provide relates to the length value.
In fact we already got it wrong once, see 11e9ed43ca "Fix up
ibm_architecture_vec definition".
So add some macros to make it (hopefully) clearer. These at least have
the property that the integer present in the code is equal to the number
of bytes that follows it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
This patch adds the ability to the DMA direct ops to fallback to the IOMMU
ops for coherent alloc/free if the coherent mask of the device isn't
suitable for accessing the direct DMA space and the device also happens
to have an active IOMMU table.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that the table and the offset can co-exist, we no longer need
to flip/flop, we can just establish both once at boot time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To support "hybrid" DMA ops in a subsequent patch, we will need both
a direct DMA offset and an iommu pointer. Those are currently exclusive
(a union), so change them to be separate fields.
While there, also type iommu_table_base properly and make exist only
on CONFIG_PPC64 since it's not referenced on 32-bit at all.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
core_idle_state is maintained for each core. It uses 0-7 bits to track
whether a thread in the core has entered fastsleep or winkle. 8th bit is
used as a lock bit.
The lock bit is set in these 2 scenarios-
- The thread is first in subcore to wakeup from sleep/winkle.
- If its the last thread in the core about to enter sleep/winkle
While the lock bit is set, if any other thread in the core wakes up, it
loops until the lock bit is cleared before proceeding in the wakeup
path. This helps prevent race conditions w.r.t fastsleep workaround and
prevents threads from switching to process context before core/subcore
resources are restored.
But, in the path to sleep/winkle entry, we currently don't check for
lock-bit. This exposes us to following race when running with subcore
on-
First thread in the subcorea Another thread in the same
waking up core entering sleep/winkle
lwarx r15,0,r14
ori r15,r15,PNV_CORE_IDLE_LOCK_BIT
stwcx. r15,0,r14
[Code to restore subcore state]
lwarx r15,0,r14
[clear thread bit]
stwcx. r15,0,r14
andi. r15,r15,PNV_CORE_IDLE_THREAD_BITS
stw r15,0(r14)
Here, after the thread entering sleep clears its thread bit in
core_idle_state, the value is overwritten by the thread waking up.
In such cases when the core enters fastsleep, code mistakes an idle
thread as running. Because of this, the first thread waking up from
fastsleep which is supposed to resync timebase skips it. So we can
end up having a core with stale timebase value.
This patch fixes the above race by looping on the lock bit even while
entering the idle states.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Fixes: 7b54e9f213f76 'powernv/powerpc: Add winkle support for offline cpus'
Cc: stable@vger.kernel.org # 3.19+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The conversion of opal events to a proper irqchip means that handlers
are called until the relevant opal event has been cleared by
processing it. Events that queue work should therefore use a threaded
handler to mask the event until processing is complete.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Tested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An earlier commit referenced 'hose_list' in sysdev/ppc4xx_hsta_msi.c.
hose_list is defined in ppc-pci.h, which was not included in that
file. Include it, fixing the build for the akebono defconfig used
by the kbuild test robot.
Fixes: f2c800aace ("powerpc/ppc4xx_hsta_msi: Move MSI-related ops to pci_controller_ops")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If we take an alignment exception which we cannot fix, the oops
currently prints:
Unable to handle kernel paging request for unknown fault
Lets print something more useful:
Unable to handle kernel paging request for unaligned access at address 0xc0000000f77bba8f
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This means the 'M' flag will work properly when the kernel prints a backtrace.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
opal-prd driver will mmap() firmware code/data area as private
mapping to prd user space daemon. Write to this page will
trigger COW faults. The new COW pages are normal kernel RAM
pages accounted by the kernel and are not special.
vma->vm_page_prot value will be used at page fault time
for the new COW pages, while pgprot_t value passed in
remap_pfn_range() is used for the initial page table entry.
Hence:
* Do not add _PAGE_SPECIAL in vma, but only for remap_pfn_range()
* Also remap_pfn_range() will add the _PAGE_SPECIAL flag using
pte_mkspecial() call, hence no need to specify in the driver
This fix resolves the page accounting warning shown below:
BUG: Bad rss-counter state mm:c0000007d34ac600 idx:1 val:19
The above warning is triggered since _PAGE_SPECIAL was incorrectly
being set for the normal kernel COW pages.
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull more vfs updates from Al Viro:
"Assorted VFS fixes and related cleanups (IMO the most interesting in
that part are f_path-related things and Eric's descriptor-related
stuff). UFS regression fixes (it got broken last cycle). 9P fixes.
fs-cache series, DAX patches, Jan's file_remove_suid() work"
[ I'd say this is much more than "fixes and related cleanups". The
file_table locking rule change by Eric Dumazet is a rather big and
fundamental update even if the patch isn't huge. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (49 commits)
9p: cope with bogus responses from server in p9_client_{read,write}
p9_client_write(): avoid double p9_free_req()
9p: forgetting to cancel request on interrupted zero-copy RPC
dax: bdev_direct_access() may sleep
block: Add support for DAX reads/writes to block devices
dax: Use copy_from_iter_nocache
dax: Add block size note to documentation
fs/file.c: __fget() and dup2() atomicity rules
fs/file.c: don't acquire files->file_lock in fd_install()
fs:super:get_anon_bdev: fix race condition could cause dev exceed its upper limitation
vfs: avoid creation of inode number 0 in get_next_ino
namei: make set_root_rcu() return void
make simple_positive() public
ufs: use dir_pages instead of ufs_dir_pages()
pagemap.h: move dir_pages() over there
remove the pointless include of lglock.h
fs: cleanup slight list_entry abuse
xfs: Correctly lock inode when removing suid and file capabilities
fs: Call security_ops->inode_killpriv on truncate
fs: Provide function telling whether file_remove_privs() will do anything
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KDJO
-----END PGP SIGNATURE-----
Merge tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part two from Paul Gortmaker:
"Replace module_init with appropriate alternate initcall in non
modules.
This series converts non-modular code that is using the module_init()
call to hook itself into the system to instead use one of our
alternate priority initcalls.
Unlike the previous series that used device_initcall and hence was a
runtime no-op, these commits change to one of the alternate initcalls,
because (a) we have them and (b) it seems like the right thing to do.
For example, it would seem logical to use arch_initcall for arch
specific setup code and fs_initcall for filesystem setup code.
This does mean however, that changes in the init ordering will be
taking place, and so there is a small risk that some kind of implicit
init ordering issue may lie uncovered. But I think it is still better
to give these ones sensible priorities than to just assign them all to
device_initcall in order to exactly preserve the old ordering.
Thad said, we have already made similar changes in core kernel code in
commit c96d6660dc ("kernel: audit/fix non-modular users of
module_init in core code") without any regressions reported, so this
type of change isn't without precedent. It has also got the same
local testing and linux-next coverage as all the other pull requests
that I'm sending for this merge window have got.
Once again, there is an unused module_exit function removal that shows
up as an outlier upon casual inspection of the diffstat"
* tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
x86: perf_event_intel_pt.c: use arch_initcall to hook in enabling
x86: perf_event_intel_bts.c: use arch_initcall to hook in enabling
mm/page_owner.c: use late_initcall to hook in enabling
lib/list_sort: use late_initcall to hook in self tests
arm: use subsys_initcall in non-modular pl320 IPC code
powerpc: don't use module_init for non-modular core hugetlb code
powerpc: use subsys_initcall for Freescale Local Bus
x86: don't use module_init for non-modular core bootflag code
netfilter: don't use module_init/exit in core IPV4 code
fs/notify: don't use module_init for non-modular inotify_user code
mm: replace module_init usages with subsys_initcall in nommu.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVkO5XAAoJEOvOhAQsB9HWe4cQAJcsmSXIDN2O6oxvgH8Wilof
EIEMvT13uwBdsjQdYUY6A6B3iUV9wzEEgoosg/JRgpz5/b1FTDMIO4arUPD3Lcak
5bmyVO2qAT+yaLAWSgn6I8DMplXrKiEuK+TkH/mW3p9TdvElLdG3Vg6UI407hSWv
W0QbVwkNtv8XmzshV9F2YdmflT8j1PgYxIu/tEkVOWn37DNW+Fp2OVBrdTIYp3AJ
X6bYZPEcQDCrWWW/s2GmIDrNgryiebasns+CAgGY21262jAYaRcFOJmR47AsTqW7
DSZXIlLc/gJca++hfxqV15RZ4NRHxrebCypTsPtZUV7ZiYHI726eeUZzxsp/9itu
mvhmi+aQUTTUP3dDhiv05f4syAKEb4zslT6SLwcna6oi09M97HfCeQsHqhcFq/MG
KnS2JJoJQToQtJvMUXMQzp5hyHjNlOclIvCxEiL32EZU54PeJOKasy/mptNGEctk
TxACWvoXBQglRaVN+1wIjjr0BaHJSuJa9CUnIfM4WZdSHiMQMx00XLTkZcTnSM6R
12pE54vVolrXswGPJhy4W/Sf1yPSW1tkWSVBbkKLyCIrlAWJtu68rXhvwhG/nz6E
3g6QrDEQGlk6bzUH4CJCEqXLPRN1bNS0XjdkEFh60Lury3Ns5yHKZXPW5vCQ5csr
FQNUyBs595CWbJNfbn1n
=0BDx
-----END PGP SIGNATURE-----
Merge tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part one from Paul Gortmaker:
"Replace module_init with equivalent device_initcall in non modules.
This series of commits converts non-modular code that is using the
module_init() call to hook itself into the system to instead use
device_initcall().
The conversion is a runtime no-op, since module_init actually becomes
__initcall in the non-modular case, and that in turn gets mapped onto
device_initcall. A couple files show a larger negative diffstat,
representing ones that had a module_exit function that we remove here
vs previously relying on the linker to dispose of it.
We make this conversion now, so that we can relocate module_init from
init.h into module.h in the future.
The files changed here are just limited to those that would otherwise
have to add module.h to obviously non-modular code, in order to avoid
a compile fail, as testing has shown"
* tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MIPS: don't use module_init in non-modular cobalt/mtd.c file
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
cris: don't use module_init for non-modular core eeprom.c code
tty/metag_da: Avoid module_init/module_exit in non-modular code
drivers/clk: don't use module_init in clk-nomadik.c which is non-modular
xtensa: don't use module_init for non-modular core network.c code
sh: don't use module_init in non-modular psw.c code
mn10300: don't use module_init in non-modular flash.c code
parisc64: don't use module_init for non-modular core perf code
parisc: don't use module_init for non-modular core pdc_cons code
cris: don't use module_init for non-modular core intmem.c code
ia64: don't use module_init in non-modular sim/simscsi.c code
ia64: don't use module_init for non-modular core kernel/mca.c code
arm: don't use module_init in non-modular mach-vexpress/spc.c code
powerpc: don't use module_init in non-modular 83xx suspend code
powerpc: use device_initcall for registering rtc devices
x86: don't use module_init in non-modular devicetree.c code
x86: don't use module_init in non-modular intel_mid_vrtc.c
A whole lot of bug fixes. Nothing stands out here except the ability to
enable CONFIG_OF on every architecture, and an import of a newer version
of dtc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tm5y
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree updates from Grant Likely:
"A whole lot of bug fixes.
Nothing stands out here except the ability to enable CONFIG_OF on
every architecture, and an import of a newer version of dtc"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (22 commits)
of/irq: Rename "intc_desc" to "of_intc_desc" to fix OF on sh
of/irq: Fix pSeries boot failure
Documentation: DT: Fix a typo in the filename "lantiq,<chip>-pinumx.txt"
of: define of_find_node_by_phandle for !CONFIG_OF
of/address: use atomic allocation in pci_register_io_range()
of: Add vendor prefix for Zodiac Inflight Innovations
dt/fdt: add empty versions of early_init_dt_*_memory_arch
of: clean-up unnecessary libfdt include paths
of: make unittest select OF_EARLY_FLATTREE instead of depend on it
of: make CONFIG_OF user selectable
MIPS: prepare for user enabling of CONFIG_OF
of/fdt: fix argument name and add comments of unflatten_dt_node()
of: return NUMA_NO_NODE from fallback of_node_to_nid()
tps6507x.txt: Remove executable permission
of/overlay: Grammar s/an negative/a negative/
of/fdt: Make fdt blob input parameters of unflatten functions const
of: add helper function to retrive match data
of: Grammar s/property exist/property exists/
of: Move OF flags to be visible even when !CONFIG_OF
scripts/dtc: Update to upstream version 9d3649bd3be245c9
...
Here is the driver core / firmware changes for 4.2-rc1.
A number of small changes all over the place in the driver core, and in
the firmware subsystem. Nothing really major, full details in the
shortlog. Some of it is a bit of churn, given that the platform driver
probing changes was found to not work well, so they were reverted.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNoCQACgkQMUfUDdst+ym4JACdFrrXoMt2pb8nl5gMidGyM9/D
jg8AnRgdW8ArDA/xOarULd/X43eA3J3C
=Al2B
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the driver core / firmware changes for 4.2-rc1.
A number of small changes all over the place in the driver core, and
in the firmware subsystem. Nothing really major, full details in the
shortlog. Some of it is a bit of churn, given that the platform
driver probing changes was found to not work well, so they were
reverted.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (31 commits)
Revert "base/platform: Only insert MEM and IO resources"
Revert "base/platform: Continue on insert_resource() error"
Revert "of/platform: Use platform_device interface"
Revert "base/platform: Remove code duplication"
firmware: add missing kfree for work on async call
fs: sysfs: don't pass count == 0 to bin file readers
base:dd - Fix for typo in comment to function driver_deferred_probe_trigger().
base/platform: Remove code duplication
of/platform: Use platform_device interface
base/platform: Continue on insert_resource() error
base/platform: Only insert MEM and IO resources
firmware: use const for remaining firmware names
firmware: fix possible use after free on name on asynchronous request
firmware: check for file truncation on direct firmware loading
firmware: fix __getname() missing failure check
drivers: of/base: move of_init to driver_init
drivers/base: cacheinfo: fix annoying typo when DT nodes are absent
sysfs: disambiguate between "error code" and "failure" in comments
driver-core: fix build for !CONFIG_MODULES
driver-core: make __device_attach() static
...
Merge second patchbomb from Andrew Morton:
- most of the rest of MM
- lots of misc things
- procfs updates
- printk feature work
- updates to get_maintainer, MAINTAINERS, checkpatch
- lib/ updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (96 commits)
exit,stats: /* obey this comment */
coredump: add __printf attribute to cn_*printf functions
coredump: use from_kuid/kgid when formatting corename
fs/reiserfs: remove unneeded cast
NILFS2: support NFSv2 export
fs/befs/btree.c: remove unneeded initializations
fs/minix: remove unneeded cast
init/do_mounts.c: add create_dev() failure log
kasan: remove duplicate definition of the macro KASAN_FREE_PAGE
fs/efs: femove unneeded cast
checkpatch: emit "NOTE: <types>" message only once after multiple files
checkpatch: emit an error when there's a diff in a changelog
checkpatch: validate MODULE_LICENSE content
checkpatch: add multi-line handling for PREFER_ETHER_ADDR_COPY
checkpatch: suggest using eth_zero_addr() and eth_broadcast_addr()
checkpatch: fix processing of MEMSET issues
checkpatch: suggest using ether_addr_equal*()
checkpatch: avoid NOT_UNIFIED_DIFF errors on cover-letter.patch files
checkpatch: remove local from codespell path
checkpatch: add --showfile to allow input via pipe to show filenames
...
Nobody used these hooks so they were removed from common code, and can now
be removed from the architectures.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
