commit ea2a1cfc3b upstream.
Commit 73d9629e1c ("i40e: Do not allow untrusted VF to remove
administratively set MAC") fixed an issue where untrusted VF was
allowed to remove its own MAC address although this was assigned
administratively from PF. Unfortunately the introduced check
is wrong because it causes that MAC filters for other MAC addresses
including multi-cast ones are not removed.
<snip>
if (ether_addr_equal(addr, vf->default_lan_addr.addr) &&
i40e_can_vf_change_mac(vf))
was_unimac_deleted = true;
else
continue;
if (i40e_del_mac_filter(vsi, al->list[i].addr)) {
...
</snip>
The else path with `continue` effectively skips any MAC filter
removal except one for primary MAC addr when VF is allowed to do so.
Fix the check condition so the `continue` is only done for primary
MAC address.
Fixes: 73d9629e1c ("i40e: Do not allow untrusted VF to remove administratively set MAC")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240329180638.211412-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8edfc7a40e upstream.
ice_port_vlan_on/off() was introduced in commit 2946204b3f ("ice:
implement bridge port vlan"). But ice_port_vlan_on() incorrectly assigns
ena_rx_filtering to inner_vlan_ops in DVM mode.
This causes an error when rx_filtering cannot be enabled in legacy mode.
Reproducer:
echo 1 > /sys/class/net/$PF/device/sriov_numvfs
ip link set $PF vf 0 spoofchk off trust on vlan 3
dmesg:
ice 0000:41:00.0: failed to enable Rx VLAN filtering for VF 0 VSI 9 during VF rebuild, error -95
Fixes: 2946204b3f ("ice: implement bridge port vlan")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd19e827d6 upstream.
In the very rare case where a packet type is unknown to the driver,
idpf_rx_process_skb_fields would return early without calling
eth_type_trans to set the skb protocol / the network layer handler.
This is especially problematic if tcpdump is running when such a
packet is received, i.e. it would cause a kernel panic.
Instead, call eth_type_trans for every single packet, even when
the packet type is unknown.
Fixes: 3a8845af66 ("idpf: add RX splitq napi poll support")
Reported-by: Balazs Nemeth <bnemeth@redhat.com>
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Salvatore Daniele <sdaniele@redhat.com>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed4cccef64 upstream.
If packets are GROed with fraglist they might be segmented later on and
continue their journey in the stack. In skb_segment_list those skbs can
be reused as-is. This is an issue as their destructor was removed in
skb_gro_receive_list but not the reference to their socket, and then
they can't be orphaned. Fix this by also removing the reference to the
socket.
For example this could be observed,
kernel BUG at include/linux/skbuff.h:3131! (skb_orphan)
RIP: 0010:ip6_rcv_core+0x11bc/0x19a0
Call Trace:
ipv6_list_rcv+0x250/0x3f0
__netif_receive_skb_list_core+0x49d/0x8f0
netif_receive_skb_list_internal+0x634/0xd40
napi_complete_done+0x1d2/0x7d0
gro_cell_poll+0x118/0x1f0
A similar construction is found in skb_gro_receive, apply the same
change there.
Fixes: 5e10da5385 ("skbuff: allow 'slow_gro' for skb carring sock reference")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fb101be97 upstream.
UDP tunnel packets can't be GRO in-between their endpoints as this
causes different issues. The UDP GRO fwd vxlan tests were relying on
this and their expectations have to be fixed.
We keep both vxlan tests and expected no GRO from happening. The vxlan
UDP GRO bench test was removed as it's not providing any valuable
information now.
Fixes: a062260a9d ("selftests: net: add UDP GRO forwarding self-tests")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 625aefac34 upstream.
The switch has 4 ports with 2 internal PHYs, but ports are numbered up
to 6, with ports 0, 1, 5 and 6 being usable.
Fixes: 71d94a432a ("net: dsa: mv88e6xxx: add support for MV88E6020 switch")
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326123655.40666-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96c155943a upstream.
In lan8814_get_sig_rx() and lan8814_get_sig_tx() ptp_parse_header() may
return NULL as ptp_header due to abnormal packet type or corrupted packet.
Fix this bug by adding ptp_header check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240329061631.33199-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbc17e7802 upstream.
Setting mac_managed_pm during interface up is too late.
In situations where the link is not brought up yet and the system suspends
the regular PHY power management will run. Since the FEC ETHEREN control
bit is cleared (automatically) on suspend the controller is off in resume.
When the regular PHY power management resume path runs in this context it
will write to the MII_DATA register but nothing will be transmitted on the
MDIO bus.
This can be observed by the following log:
fec 5b040000.ethernet eth0: MDIO read timeout
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: dpm_run_callback(): mdio_bus_phy_resume+0x0/0xc8 returns -110
Microchip LAN87xx T1 5b040000.ethernet-1:04: PM: failed to resume: error -110
The data written will however remain in the MII_DATA register.
When the link later is set to administrative up it will trigger a call to
fec_restart() which will restore the MII_SPEED register. This triggers the
quirk explained in f166f890c8 ("net: ethernet: fec: Replace interrupt
driven MDIO with polled IO") causing an extra MII_EVENT.
This extra event desynchronizes all the MDIO register reads, causing them
to complete too early. Leading all reads to read as 0 because
fec_enet_mdio_wait() returns too early.
When a Microchip LAN8700R PHY is connected to the FEC, the 0 reads causes
the PHY to be initialized incorrectly and the PHY will not transmit any
ethernet signal in this state. It cannot be brought out of this state
without a power cycle of the PHY.
Fixes: 557d5dc83f ("net: fec: use mac-managed PHY PM")
Closes: https://lore.kernel.org/netdev/1f45bdbe-eab1-4e59-8f24-add177590d27@actia.se/
Signed-off-by: Wei Fang <wei.fang@nxp.com>
[jernberg: commit message]
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://lore.kernel.org/r/20240328155909.59613-2-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de99e1ea3a upstream.
There are 2 issues with the blamed commit.
1. When the phy is initialized, it would enable the disabled of UDPv4
checksums. The UDPv6 checksum is already enabled by default. So when
1-step is configured then it would clear these flags.
2. After the 1-step is configured, then if 2-step is configured then the
1-step would be still configured because it is not clearing the flag.
So the sync frames will still have origin timestamps set.
Fix this by reading first the value of the register and then
just change bit 12 as this one determines if the timestamp needs to
be inserted in the frame, without changing any other bits.
Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Link: https://lore.kernel.org/r/20240402071634.2483524-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3da86d432 upstream.
The driver should ensure that same priority is not mapped to multiple
rx queues. From DesignWare Cores Ethernet Quality-of-Service
Databook, section 17.1.29 MAC_RxQ_Ctrl2:
"[...]The software must ensure that the content of this field is
mutually exclusive to the PSRQ fields for other queues, that is,
the same priority is not mapped to multiple Rx queues[...]"
Previously rx_queue_priority() function was:
- clearing all priorities from a queue
- adding new priorities to that queue
After this patch it will:
- first assign new priorities to a queue
- then remove those priorities from all other queues
- keep other priorities previously assigned to that queue
Fixes: a8f5102af2 ("net: stmmac: TX and RX queue priority configuration")
Fixes: 2142754f8b ("net: stmmac: Add MAC related callbacks for XGMAC2")
Signed-off-by: Piotr Wejman <piotrwejman90@gmail.com>
Link: https://lore.kernel.org/r/20240401192239.33942-1-piotrwejman90@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c120209bce upstream.
The definition and declaration of sja1110_pcs_mdio_write_c45() don't have
parameters in the same order.
Knowing that sja1110_pcs_mdio_write_c45() is used as a function pointer
in 'sja1105_info' structure with .pcs_mdio_write_c45, and that we have:
int (*pcs_mdio_write_c45)(struct mii_bus *bus, int phy, int mmd,
int reg, u16 val);
it is likely that the definition is the one to change.
Found with cppcheck, funcArgOrderDifferent.
Fixes: ae271547bb ("net: dsa: sja1105: C45 only transactions for PCS")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/ff2a5af67361988b3581831f7bd1eddebfb4c48f.1712082763.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c36a15673 upstream.
When zapping a table entry in stage2_try_break_pte(), we issue range
TLB invalidation for the region that was mapped by the table. However,
we neglect to align the base address down to the granule size and so
if we ended up reaching the table entry via a misaligned address then
we will accidentally skip invalidation for some prefix of the affected
address range.
Align 'ctx->addr' down to the granule size when performing TLB
invalidation for an unmapped table in stage2_try_break_pte().
Cc: Raghavendra Rao Ananta <rananta@google.com>
Cc: Gavin Shan <gshan@redhat.com>
Cc: Shaoqin Huang <shahuang@redhat.com>
Cc: Quentin Perret <qperret@google.com>
Fixes: defc8cc7ab ("KVM: arm64: Invalidate the table entries upon a range")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240327124853.11206-5-will@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f0ff097bf upstream.
Commit c910f2b655 ("arm64/mm: Update tlb invalidation routines for
FEAT_LPA2") updated the __tlbi_level() macro to take the target level
as an argument, with TLBI_TTL_UNKNOWN (rather than 0) indicating that
the caller cannot provide level information. Unfortunately, the two
implementations of __kvm_tlb_flush_vmid_range() were not updated and so
now ask for an level 0 invalidation if FEAT_LPA2 is implemented.
Fix the problem by passing TLBI_TTL_UNKNOWN instead of 0 as the level
argument to __flush_s2_tlb_range_op() in __kvm_tlb_flush_vmid_range().
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Oliver Upton <oliver.upton@linux.dev>
Cc: Marc Zyngier <maz@kernel.org>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Fixes: c910f2b655 ("arm64/mm: Update tlb invalidation routines for FEAT_LPA2")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240327124853.11206-4-will@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e11073247 upstream.
The srso_alias_untrain_ret() dummy thunk in the !CONFIG_MITIGATION_SRSO
case is there only for the altenative in CALL_UNTRAIN_RET to have
a symbol to resolve.
However, testing with kernels which don't have CONFIG_MITIGATION_SRSO
enabled, leads to the warning in patch_return() to fire:
missing return thunk: srso_alias_untrain_ret+0x0/0x10-0x0: eb 0e 66 66 2e
WARNING: CPU: 0 PID: 0 at arch/x86/kernel/alternative.c:826 apply_returns (arch/x86/kernel/alternative.c:826
Put in a plain "ret" there so that gcc doesn't put a return thunk in
in its place which special and gets checked.
In addition:
ERROR: modpost: "srso_alias_untrain_ret" [arch/x86/kvm/kvm-amd.ko] undefined!
make[2]: *** [scripts/Makefile.modpost:145: Module.symvers] Chyba 1
make[1]: *** [/usr/src/linux-6.8.3/Makefile:1873: modpost] Chyba 2
make: *** [Makefile:240: __sub-make] Chyba 2
since !SRSO builds would use the dummy return thunk as reported by
petr.pisar@atlas.cz, https://bugzilla.kernel.org/show_bug.cgi?id=218679.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202404020901.da75a60f-oliver.sang@intel.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/all/202404020901.da75a60f-oliver.sang@intel.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff91059932 upstream.
syzkaller started using corpuses where a BPF tracing program deletes
elements from a sockmap/sockhash map. Because BPF tracing programs can be
invoked from any interrupt context, locks taken during a map_delete_elem
operation must be hardirq-safe. Otherwise a deadlock due to lock inversion
is possible, as reported by lockdep:
CPU0 CPU1
---- ----
lock(&htab->buckets[i].lock);
local_irq_disable();
lock(&host->lock);
lock(&htab->buckets[i].lock);
<Interrupt>
lock(&host->lock);
Locks in sockmap are hardirq-unsafe by design. We expects elements to be
deleted from sockmap/sockhash only in task (normal) context with interrupts
enabled, or in softirq context.
Detect when map_delete_elem operation is invoked from a context which is
_not_ hardirq-unsafe, that is interrupts are disabled, and bail out with an
error.
Note that map updates are not affected by this issue. BPF verifier does not
allow updating sockmap/sockhash from a BPF tracing program today.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Reported-by: xingwei lee <xrivendell7@gmail.com>
Reported-by: yue sun <samsun1006219@gmail.com>
Reported-by: syzbot+bc922f476bd65abbd466@syzkaller.appspotmail.com
Reported-by: syzbot+d4066896495db380182e@syzkaller.appspotmail.com
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: syzbot+d4066896495db380182e@syzkaller.appspotmail.com
Acked-by: John Fastabend <john.fastabend@gmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=d4066896495db380182e
Closes: https://syzkaller.appspot.com/bug?extid=bc922f476bd65abbd466
Link: https://lore.kernel.org/bpf/20240402104621.1050319-1-jakub@cloudflare.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de3f64b738 upstream.
If an load_nls_xxx() function fails a few lines above, the 'sbi->bdi_id' is
still 0.
So, in the error handling path, we will call ida_simple_remove(..., 0)
which is not allocated yet.
In order to prevent a spurious "ida_free called for id=0 which is not
allocated." message, tweak the error handling path and add a new label.
Fixes: 0fd1695766 ("fs: Add VirtualBox guest shared folder (vboxsf) support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/d09eaaa4e2e08206c58a1a27ca9b3e81dc168773.1698835730.git.christophe.jaillet@wanadoo.fr
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bc83a019b upstream.
Hook unregistration is deferred to the commit phase, same occurs with
hook updates triggered by the table dormant flag. When both commands are
combined, this results in deleting a basechain while leaving its hook
still registered in the core.
Fixes: 179d9ba555 ("netfilter: nf_tables: fix table flag updates")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24225011d8 upstream.
nft_unregister_flowtable_type() within nf_flow_inet_module_exit() can
concurrent with __nft_flowtable_type_get() within nf_tables_newflowtable().
And thhere is not any protection when iterate over nf_tables_flowtables
list in __nft_flowtable_type_get(). Therefore, there is pertential
data-race of nf_tables_flowtables list entry.
Use list_for_each_entry_rcu() to iterate over nf_tables_flowtables list
in __nft_flowtable_type_get(), and use rcu_read_lock() in the caller
nft_flowtable_type_get() to protect the entire type query process.
Fixes: 3b49e2e94e ("netfilter: nf_tables: add flow table netlink frontend")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b32a09ea7c upstream.
Commit 82dfb540ae ("VSOCK: Add virtio vsock vsockmon hooks") added
virtio_transport_deliver_tap_pkt() for handing packets to the
vsockmon device. However, in virtio_transport_send_pkt_work(),
the function is called before actually sending the packet (i.e.
before placing it in the virtqueue with virtqueue_add_sgs() and checking
whether it returned successfully).
Queuing the packet in the virtqueue can fail even multiple times.
However, in virtio_transport_deliver_tap_pkt() we deliver the packet
to the monitoring tap interface only the first time we call it.
This certainly avoids seeing the same packet replicated multiple times
in the monitoring interface, but it can show the packet sent with the
wrong timestamp or even before we succeed to queue it in the virtqueue.
Move virtio_transport_deliver_tap_pkt() after calling virtqueue_add_sgs()
and making sure it returned successfully.
Fixes: 82dfb540ae ("VSOCK: Add virtio vsock vsockmon hooks")
Cc: stable@vge.kernel.org
Signed-off-by: Marco Pinna <marco.pinn95@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20240329161259.411751-1-marco.pinn95@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0de6ab920 upstream.
mana_get_rxbuf_cfg() aligns the RX buffer's DMA datasize to be
multiple of 64. So a packet slightly bigger than mtu+14, say 1536,
can be received and cause skb_over_panic.
Sample dmesg:
[ 5325.237162] skbuff: skb_over_panic: text:ffffffffc043277a len:1536 put:1536 head:ff1100018b517000 data:ff1100018b517100 tail:0x700 end:0x6ea dev:<NULL>
[ 5325.243689] ------------[ cut here ]------------
[ 5325.245748] kernel BUG at net/core/skbuff.c:192!
[ 5325.247838] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 5325.258374] RIP: 0010:skb_panic+0x4f/0x60
[ 5325.302941] Call Trace:
[ 5325.304389] <IRQ>
[ 5325.315794] ? skb_panic+0x4f/0x60
[ 5325.317457] ? asm_exc_invalid_op+0x1f/0x30
[ 5325.319490] ? skb_panic+0x4f/0x60
[ 5325.321161] skb_put+0x4e/0x50
[ 5325.322670] mana_poll+0x6fa/0xb50 [mana]
[ 5325.324578] __napi_poll+0x33/0x1e0
[ 5325.326328] net_rx_action+0x12e/0x280
As discussed internally, this alignment is not necessary. To fix
this bug, remove it from the code. So oversized packets will be
marked as CQE_RX_TRUNCATED by NIC, and dropped.
Cc: stable@vger.kernel.org
Fixes: 2fbbd712ba ("net: mana: Enable RX path to handle various MTU sizes")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/1712087316-20886-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e91bb99b9 upstream.
After the commit d2689b6a86 ("net: usb: ax88179_178a: avoid two
consecutive device resets"), reset is not executed from bind operation and
mac address is not read from the device registers or the devicetree at that
moment. Since the check to configure if the assigned mac address is random
or not for the interface, happens after the bind operation from
usbnet_probe, the interface keeps configured as random address, although the
address is correctly read and set during open operation (the only reset
now).
In order to keep only one reset for the device and to avoid the interface
always configured as random address, after reset, configure correctly the
suitable field from the driver, if the mac address is read successfully from
the device registers or the devicetree. Take into account if a locally
administered address (random) was previously stored.
cc: stable@vger.kernel.org # 6.6+
Fixes: d2689b6a86 ("net: usb: ax88179_178a: avoid two consecutive device resets")
Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240403132158.344838-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62fc3357e0 upstream.
cp might be null, calling cp->cp_conn would produce null dereference
[Simon Horman adds:]
Analysis:
* cp is a parameter of __rds_rdma_map and is not reassigned.
* The following call-sites pass a NULL cp argument to __rds_rdma_map()
- rds_get_mr()
- rds_get_mr_for_dest
* Prior to the code above, the following assumes that cp may be NULL
(which is indicative, but could itself be unnecessary)
trans_private = rs->rs_transport->get_mr(
sg, nents, rs, &mr->r_key, cp ? cp->cp_conn : NULL,
args->vec.addr, args->vec.bytes,
need_odp ? ODP_ZEROBASED : ODP_NOT_NEEDED);
* The code modified by this patch is guarded by IS_ERR(trans_private),
where trans_private is assigned as per the previous point in this analysis.
The only implementation of get_mr that I could locate is rds_ib_get_mr()
which can return an ERR_PTR if the conn (4th) argument is NULL.
* ret is set to PTR_ERR(trans_private).
rds_ib_get_mr can return ERR_PTR(-ENODEV) if the conn (4th) argument is NULL.
Thus ret may be -ENODEV in which case the code in question will execute.
Conclusion:
* cp may be NULL at the point where this patch adds a check;
this patch does seem to address a possible bug
Fixes: c055fc00c0 ("net/rds: fix WARNING in rds_conn_connect_if_down")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mahmoud Adam <mngyadam@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240326153132.55580-1-mngyadam@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 037965402a upstream.
Notice that skb_mark_for_recycle() is introduced later than fixes tag in
commit 6a5bcd84e8 ("page_pool: Allow drivers to hint on SKB recycling").
It is believed that fixes tag were missing a call to page_pool_release_page()
between v5.9 to v5.14, after which is should have used skb_mark_for_recycle().
Since v6.6 the call page_pool_release_page() were removed (in
commit 535b9c61bd ("net: page_pool: hide page_pool_release_page()")
and remaining callers converted (in commit 6bfef2ec01 ("Merge branch
'net-page_pool-remove-page_pool_release_page'")).
This leak became visible in v6.8 via commit dba1b8a7ab ("mm/page_pool: catch
page_pool memory leaks").
Cc: stable@vger.kernel.org
Fixes: 6c5aa6fc4d ("xen networking: add basic XDP support for xen-netfront")
Reported-by: Leonidas Spyropoulos <artafinde@archlinux.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218654
Reported-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/171154167446.2671062.9127105384591237363.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40061817d9 upstream.
There's a bug in pm_nl_check_endpoint(), 'dev' didn't be parsed correctly.
If calling it in the 2nd test of endpoint_tests() too, it fails with an
error like this:
creation [FAIL] expected '10.0.2.2 id 2 subflow dev dev' \
found '10.0.2.2 id 2 subflow dev ns2eth2'
The reason is '$2' should be set to 'dev', not '$1'. This patch fixes it.
Fixes: 69c6ce7b6e ("selftests: mptcp: add implicit endpoint test case")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240329-upstream-net-20240329-fallback-mib-v1-2-324a8981da48@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d459e2ffb upstream.
The commit mutex should not be released during the critical section
between nft_gc_seq_begin() and nft_gc_seq_end(), otherwise, async GC
worker could collect expired objects and get the released commit lock
within the same GC sequence.
nf_tables_module_autoload() temporarily releases the mutex to load
module dependencies, then it goes back to replay the transaction again.
Move it at the end of the abort phase after nft_gc_seq_end() is called.
Cc: stable@vger.kernel.org
Fixes: 720344340f ("netfilter: nf_tables: GC transaction race with abort path")
Reported-by: Kuan-Ting Chen <hexrabbit@devco.re>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a45e688957 upstream.
Unlike early commit path stage which triggers a call to abort, an
explicit release of the batch is required on abort, otherwise mutex is
released and commit_list remains in place.
Add WARN_ON_ONCE to ensure commit_list is empty from the abort path
before releasing the mutex.
After this patch, commit_list is always assumed to be empty before
grabbing the mutex, therefore
03c1f1ef15 ("netfilter: Cleanup nft_net->module_list from nf_tables_exit_net()")
only needs to release the pending modules for registration.
Cc: stable@vger.kernel.org
Fixes: c0391b6ab8 ("netfilter: nf_tables: missing validation from the abort path")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7835fcfd13 upstream.
struct hci_dev members conn_info_max_age, conn_info_min_age,
le_conn_max_interval, le_conn_min_interval, le_adv_max_interval,
and le_adv_min_interval can be modified from the HCI core code, as well
through debugfs.
The debugfs implementation, that's only available to privileged users,
will check for boundaries, making sure that the minimum value being set
is strictly above the maximum value that already exists, and vice-versa.
However, as both minimum and maximum values can be changed concurrently
to us modifying them, we need to make sure that the value we check is
the value we end up using.
For example, with ->conn_info_max_age set to 10, conn_info_min_age_set()
gets called from vfs handlers to set conn_info_min_age to 8.
In conn_info_min_age_set(), this goes through:
if (val == 0 || val > hdev->conn_info_max_age)
return -EINVAL;
Concurrently, conn_info_max_age_set() gets called to set to set the
conn_info_max_age to 7:
if (val == 0 || val > hdev->conn_info_max_age)
return -EINVAL;
That check will also pass because we used the old value (10) for
conn_info_max_age.
After those checks that both passed, the struct hci_dev access
is mutex-locked, disabling concurrent access, but that does not matter
because the invalid value checks both passed, and we'll end up with
conn_info_min_age = 8 and conn_info_max_age = 7
To fix this problem, we need to lock the structure access before so the
check and assignment are not interrupted.
This fix was originally devised by the BassCheck[1] team, and
considered the problem to be an atomicity one. This isn't the case as
there aren't any concerns about the variable changing while we check it,
but rather after we check it parallel to another change.
This patch fixes CVE-2024-24858 and CVE-2024-24857.
[1] https://sites.google.com/view/basscheck/
Co-developed-by: Gui-Dong Han <2045gemini@gmail.com>
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Link: https://lore.kernel.org/linux-bluetooth/20231222161317.6255-1-2045gemini@gmail.com/
Link: https://nvd.nist.gov/vuln/detail/CVE-2024-24858
Link: https://lore.kernel.org/linux-bluetooth/20231222162931.6553-1-2045gemini@gmail.com/
Link: https://lore.kernel.org/linux-bluetooth/20231222162310.6461-1-2045gemini@gmail.com/
Link: https://nvd.nist.gov/vuln/detail/CVE-2024-24857
Fixes: 31ad169148 ("Bluetooth: Add conn info lifetime parameters to debugfs")
Fixes: 729a1051da ("Bluetooth: Expose default LE advertising interval via debugfs")
Fixes: 71c3b60ec6 ("Bluetooth: Move BR/EDR debugfs file creation into hci_debugfs.c")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c569242cd4 upstream.
We have a BT headset (Lenovo Thinkplus XT99), the pairing and
connecting has no problem, once this headset is paired, bluez will
remember this device and will auto re-connect it whenever the device
is powered on. The auto re-connecting works well with Windows and
Android, but with Linux, it always fails. Through debugging, we found
at the rfcomm connection stage, the bluetooth stack reports
"Connection refused - security block (0x0003)".
For this device, the re-connecting negotiation process is different
from other BT headsets, it sends the Link_KEY_REQUEST command before
the CONNECT_REQUEST completes, and it doesn't send ENCRYPT_CHANGE
command during the negotiation. When the device sends the "connect
complete" to hci, the ev->encr_mode is 1.
So here in the conn_complete_evt(), if ev->encr_mode is 1, link type
is ACL and HCI_CONN_ENCRYPT is not set, we set HCI_CONN_ENCRYPT to
this conn, and update conn->enc_key_size accordingly.
After this change, this BT headset could re-connect with Linux
successfully. This is the btmon log after applying the patch, after
receiving the "Connect Complete" with "Encryption: Enabled", will send
the command to read encryption key size:
> HCI Event: Connect Request (0x04) plen 10
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Class: 0x240404
Major class: Audio/Video (headset, speaker, stereo, video, vcr)
Minor class: Wearable Headset Device
Rendering (Printing, Speaker)
Audio (Speaker, Microphone, Headset)
Link type: ACL (0x01)
...
> HCI Event: Link Key Request (0x17) plen 6
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Link key: ${32-hex-digits-key}
...
> HCI Event: Connect Complete (0x03) plen 11
Status: Success (0x00)
Handle: 256
Address: 8C:3C:AA:D8:11:67 (OUI 8C-3C-AA)
Link type: ACL (0x01)
Encryption: Enabled (0x01)
< HCI Command: Read Encryption Key... (0x05|0x0008) plen 2
Handle: 256
< ACL Data TX: Handle 256 flags 0x00 dlen 10
L2CAP: Information Request (0x0a) ident 1 len 2
Type: Extended features supported (0x0002)
> HCI Event: Command Complete (0x0e) plen 7
Read Encryption Key Size (0x05|0x0008) ncmd 1
Status: Success (0x00)
Handle: 256
Key size: 16
Cc: stable@vger.kernel.org
Link: https://github.com/bluez/bluez/issues/704
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39646f29b1 upstream.
Some Bluetooth controllers lack persistent storage for the device
address and instead one can be provided by the boot firmware using the
'local-bd-address' devicetree property.
The Bluetooth devicetree bindings clearly states that the address should
be specified in little-endian order, but due to a long-standing bug in
the Qualcomm driver which reversed the address some boot firmware has
been providing the address in big-endian order instead.
Add a new quirk that can be set on platforms with broken firmware and
use it to reverse the address when parsing the property so that the
underlying driver bug can be fixed.
Fixes: 5c0a1001c8 ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org # 5.1
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77f45cca8b upstream.
The WCN6855 firmware on the Lenovo ThinkPad X13s expects the Bluetooth
device address in big-endian order when setting it using the
EDL_WRITE_BD_ADDR_OPCODE command.
Presumably, this is the case for all non-ROME devices which all use the
EDL_WRITE_BD_ADDR_OPCODE command for this (unlike the ROME devices which
use a different command and expect the address in little-endian order).
Reverse the little-endian address before setting it to make sure that
the address can be configured using tools like btmgmt or using the
'local-bd-address' devicetree property.
Note that this can potentially break systems with boot firmware which
has started relying on the broken behaviour and is incorrectly passing
the address via devicetree in big-endian order.
The only device affected by this should be the WCN3991 used in some
Chromebooks. As ChromeOS updates the kernel and devicetree in lockstep,
the new 'qcom,local-bd-address-broken' property can be used to determine
if the firmware is buggy so that the underlying driver bug can be fixed
without breaking backwards compatibility.
Set the HCI_QUIRK_BDADDR_PROPERTY_BROKEN quirk for such platforms so
that the address is reversed when parsing the address property.
Fixes: 5c0a1001c8 ("Bluetooth: hci_qca: Add helper to set device address")
Cc: stable@vger.kernel.org # 5.1
Cc: Balakrishna Godavarthi <quic_bgodavar@quicinc.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Nikita Travkin <nikita@trvn.ru> # sc7180
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e12e28009e upstream.
Several Qualcomm Bluetooth controllers lack persistent storage for the
device address and instead one can be provided by the boot firmware
using the 'local-bd-address' devicetree property.
The Bluetooth bindings clearly states that the address should be
specified in little-endian order, but due to a long-standing bug in the
Qualcomm driver which reversed the address some boot firmware has been
providing the address in big-endian order instead.
The boot firmware in SC7180 Trogdor Chromebooks is known to be affected
so mark the 'local-bd-address' property as broken to maintain backwards
compatibility with older firmware when fixing the underlying driver bug.
Note that ChromeOS always updates the kernel and devicetree in lockstep
so that there is no need to handle backwards compatibility with older
devicetrees.
Fixes: 7ec3e67307 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Cc: stable@vger.kernel.org # 5.10
Cc: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4790a73ace upstream.
This reverts commit 7dcd3e014a.
Qualcomm Bluetooth controllers like WCN6855 do not have persistent
storage for the Bluetooth address and must therefore start as
unconfigured to allow the user to set a valid address unless one has
been provided by the boot firmware in the devicetree.
A recent change snuck into v6.8-rc7 and incorrectly started marking the
default (non-unique) address as valid. This specifically also breaks the
Bluetooth setup for some user of the Lenovo ThinkPad X13s.
Note that this is the second time Qualcomm breaks the driver this way
and that this was fixed last year by commit 6945795bc8 ("Bluetooth:
fix use-bdaddr-property quirk"), which also has some further details.
Fixes: 7dcd3e014a ("Bluetooth: hci_qca: Set BDA quirk bit if fwnode exists in DT")
Cc: stable@vger.kernel.org # 6.8
Cc: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reported-by: Clayton Craft <clayton@craftyguy.net>
Tested-by: Clayton Craft <clayton@craftyguy.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d98aa0883 upstream.
Adjust the IP passed to `emit_patch` so it calculates the correct offset
for the CALL instruction if `x86_call_depth_emit_accounting` emits code.
Otherwise we will skip some instructions and most likely crash.
Fixes: b2e9dfe54b ("x86/bpf: Emit call depth accounting if required")
Link: https://lore.kernel.org/lkml/20230105214922.250473-1-joanbrugueram@gmail.com/
Co-developed-by: Joan Bruguera Micó <joanbrugueram@gmail.com>
Signed-off-by: Joan Bruguera Micó <joanbrugueram@gmail.com>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/r/20240401185821.224068-2-ubizjak@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cb4a9a82b upstream.
Add CPUID_LNX_5 to track cpufeatures' word 21, and add the appropriate
compile-time assert in KVM to prevent direct lookups on the features in
CPUID_LNX_5. KVM uses X86_FEATURE_* flags to manage guest CPUID, and so
must translate features that are scattered by Linux from the Linux-defined
bit to the hardware-defined bit, i.e. should never try to directly access
scattered features in guest CPUID.
Opportunistically add NR_CPUID_WORDS to enum cpuid_leafs, along with a
compile-time assert in KVM's CPUID infrastructure to ensure that future
additions update cpuid_leafs along with NCAPINTS.
No functional change intended.
Fixes: 7f274e609f ("x86/cpufeatures: Add new word for scattered features")
Cc: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Acked-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d872c9f46 upstream.
On some boards with this chip version the BIOS is buggy and misses
to reset the PHY page selector. This results in the PHY ID read
accessing registers on a different page, returning a more or
less random value. Fix this by resetting the page selector first.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/64f2055e-98b8-45ec-8568-665e3d54d4e6@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37801a36b4 upstream.
In case kern_mount() fails and returns an error pointer return in the
error branch instead of continuing and dereferencing the error pointer.
While on it drop the never read static variable selinuxfs_mount.
Cc: stable@vger.kernel.org
Fixes: 0619f0f5e3 ("selinux: wrap selinuxfs state")
Signed-off-by: Christian Göttsche <cgzones@googlemail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5fe0adeed upstream.
Commit 11e5ea5242 ("KVM: arm64: Use helpers to classify exception
types reported via ESR") tried to abstract the translation fault
check when handling an out-of IPA space condition, but incorrectly
replaced it with a permission fault check.
Restore the previous translation fault check.
Fixes: 11e5ea5242 ("KVM: arm64: Use helpers to classify exception types reported via ESR")
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Wujie Duan <wjduan@linx-info.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/kvmarm/864jd3269g.wl-maz@kernel.org/
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e89c928bed upstream.
Programming PMU events in the host that count during guest execution is
a feature supported by perf, e.g.
perf stat -e cpu_cycles:G ./lkvm run
While this works for VHE, the guest/host event bitmaps are not carried
through to the hypervisor in the nVHE configuration. Make
kvm_pmu_update_vcpu_events() conditional on whether or not _hardware_
supports PMUv3 rather than if the vCPU as vPMU enabled.
Cc: stable@vger.kernel.org
Fixes: 84d751a019 ("KVM: arm64: Pass pmu events to hyp via vcpu")
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240305184840.636212-3-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e936e9871 upstream.
The reads to APLIC in_clrip[x] registers returns rectified input values
of the interrupt sources.
A rectified input value of an interrupt source is defined by the section
"4.5.2 Source configurations (sourcecfg[1]–sourcecfg[1023])" of the
RISC-V AIA specification as:
rectified input value = (incoming wire value) XOR (source is inverted)
Update the riscv_aplic_input() implementation to match the above.
Cc: stable@vger.kernel.org
Fixes: 74967aa208 ("RISC-V: KVM: Add in-kernel emulation of AIA APLIC")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20240321085041.1955293-3-apatel@ventanamicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8dd9f113e upstream.
The writes to setipnum_le/be register for APLIC in MSI-mode have special
consideration for level-triggered interrupts as-per the section "4.9.2
Special consideration for level-sensitive interrupt sources" of the RISC-V
AIA specification.
Particularly, the below text from the RISC-V AIA specification defines
the behaviour of writes to setipnum_le/be register for level-triggered
interrupts:
"A second option is for the interrupt service routine to write the
APLIC’s source identity number for the interrupt to the domain’s
setipnum register just before exiting. This will cause the interrupt’s
pending bit to be set to one again if the source is still asserting
an interrupt, but not if the source is not asserting an interrupt."
Fix setipnum_le/be write emulation for in-kernel APLIC by implementing
the above behaviour in aplic_write_pending() function.
Cc: stable@vger.kernel.org
Fixes: 74967aa208 ("RISC-V: KVM: Add in-kernel emulation of AIA APLIC")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20240321085041.1955293-2-apatel@ventanamicro.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b34490879b upstream.
When an interrupt is requested, a procfs directory is created under
"/proc/irq/<irqnum>/<label>" where <label> is the string passed to one of
the request_irq() variants.
What follows is that the string must not contain the "/" character or
the procfs mkdir operation will fail. We don't have such constraints for
GPIO consumer labels which are used verbatim as interrupt labels for
GPIO irqs. We must therefore sanitize the consumer string before
requesting the interrupt.
Let's replace all "/" with ":".
Cc: stable@vger.kernel.org
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Closes: https://lore.kernel.org/linux-gpio/39fe95cb-aa83-4b8b-8cab-63947a726754@gmx.net/
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c567f2948f ]
This reverts commit d794734c9b.
While the original change tries to fix a bug, it also unintentionally broke
existing systems, see the regressions reported at:
https://lore.kernel.org/all/3a1b9909-45ac-4f97-ad68-d16ef1ce99db@pavinjoseph.com/
Since d794734c9b was also marked for -stable, let's back it out before
causing more damage.
Note that due to another upstream change the revert was not 100% automatic:
0a845e0f63 mm/treewide: replace pud_large() with pud_leaf()
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: Russ Anderson <rja@hpe.com>
Cc: Steve Wahl <steve.wahl@hpe.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/3a1b9909-45ac-4f97-ad68-d16ef1ce99db@pavinjoseph.com/
Fixes: d794734c9b ("x86/mm/ident_map: Use gbpages only where full GB page should be mapped.")
Signed-off-by: Sasha Levin <sashal@kernel.org>
