If a peer device doesn't support eSCO 2M we should skip the params that
use it when setting up sync connection since they will always fail.
Signed-off-by: Yu Liu <yudiliu@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some devices, e.g. the RTL8723BS bluetooth part, some USB attached devices,
completely drop from the bus on a system-suspend. These devices will
have their driver unbound and rebound on resume (when the dropping of
the bus gets detected) and will show up as a new HCI after resume.
These devices do not benefit from the suspend / resume handling work done
by the hci_suspend_notifier. At best this unnecessarily adds some time to
the suspend/resume time. But this may also actually cause problems, if the
code doing the driver unbinding runs after the pm-notifier then the
hci_suspend_notifier code will try to talk to a device which is now in
an uninitialized state.
This commit adds a new HCI_QUIRK_NO_SUSPEND_NOTIFIER quirk which allows
drivers to opt-out of the hci_suspend_notifier when they know beforehand
that their device will be fully re-initialized / reprobed on resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth Core Specification v5.2, Vol. 3, Part A, section 1.4, table
1.1:
'Start Fragments always either begin with the first octet of the Basic
L2CAP header of a PDU or they have a length of zero (see [Vol 2] Part
B, Section 6.6.2).'
Apparently this was changed by the following errata:
https://www.bluetooth.org/tse/errata_view.cfm?errata_id=10216
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds logic to disable and reenable advertisement filters during
suspend and resume. After this patch, we would only receive packets from
devices in allow list during suspend.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enables advertising monitor offloading to the controller, if MSFT
extension is supported. The kernel won't adjust the monitor parameters
to match what the controller supports - that is the user space's
responsibility.
This patch only manages the addition of monitors. Monitor removal is
going to be handled by another patch.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
MSFT needs rssi parameter for monitoring advertisement packet,
therefore we should supply them from mgmt. This adds a new opcode
to add advertisement monitor with rssi parameters.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For advertising, we wish to know the LE tx power capabilities of the
controller in userspace, so this patch edits the Security Info MGMT
command to be more generic, such that other various controller
capabilities can be included in the EIR data. This change also includes
the LE min and max tx power into this newly-named command.
The change was tested by manually verifying that the MGMT command
returns the tx power range as expected in userspace.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Queries tx power via HCI_LE_Read_Transmit_Power command when the hci
device is initialized, and stores resulting min/max LE power in hdev
struct. If command isn't available (< BT5 support), min/max values
both default to HCI_TX_POWER_INVALID.
This patch is manually verified by ensuring BT5 devices correctly query
and receive controller tx power range.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch takes the min/max intervals and tx power optionally provided
in mgmt interface, stores them in the advertisement struct, and uses
them when configuring the hci requests. While tx power is not used if
extended advertising is unavailable, software rotation will use the min
and max advertising intervals specified by the client.
This change is validated manually by ensuring the min/max intervals are
propagated to the controller on both hatch (extended advertising) and
kukui (no extended advertising) chromebooks, and that tx power is
propagated correctly on hatch. These tests are performed with multiple
advertisements simultaneously.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds support for the new advertising add interface, with the
first command setting advertising parameters and the second to set
advertising data. The set parameters command allows the caller to leave
some fields "unset", with a params bitfield defining which params were
purposefully set. Unset parameters will be given defaults when calling
hci_add_adv_instance. The data passed to the param mgmt command is
allowed to be flexible, so in the future if bluetoothd passes a larger
structure with new params, the mgmt command will ignore the unknown
members at the end.
This change has been validated on both hatch (extended advertising) and
kukui (no extended advertising) chromebooks running bluetoothd that
support this new interface. I ran the following manual tests:
- Set several (3) advertisements using modified test_advertisement.py
- For each, validate correct data and parameters in btmon trace
- Verified both for software rotation and extended adv
Automatic test suite also run, testing many (25) scenarios of single and
multi-advertising for data/parameter correctness.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We wish to handle advertising data separately from advertising
parameters in our new MGMT requests. This change adds a helper that
allows the advertising data and scan response to be updated for an
existing advertising instance.
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch add a configurable parameter to switch off the interleave
scan feature.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch implements the interleaving between allowlist scan and
no-filter scan. It'll be used to save power when at least one monitor is
registered and at least one pending connection or one device to be
scanned for.
The durations of the allowlist scan and the no-filter scan are
controlled by MGMT command: Set Default System Configuration. The
default values are set randomly for now.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Only sockets will have the chan->data set to an actual sk, channels
like A2MP would have its own data which would likely cause a crash when
calling sk_filter, in order to fix this a new callback has been
introduced so channels can implement their own filtering if necessary.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Emit controller suspend and resume events when we are ready for suspend
and we've resumed from suspend.
The controller suspend event will report whatever suspend state was
successfully entered. The controller resume event will check the first
HCI event that was received after we finished preparing for suspend and,
if it was a connection event, store the address of the peer that caused
the event. If it was not a connection event, we mark the wake reason as
an unexpected event.
Here is a sample btmon trace with these events:
@ MGMT Event: Controller Suspended (0x002d) plen 1
Suspend state: Page scanning and/or passive scanning (2)
@ MGMT Event: Controller Resumed (0x002e) plen 8
Wake reason: Remote wake due to peer device connection (2)
LE Address: CD:F3:CD:13:C5:9A (OUI CD-F3-CD)
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the controller suspend and resume events, which will signal when
Bluetooth has completed preparing for suspend and when it's ready for
resume.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For new advertising features, it will be important for userspace to
know the capabilities of the controller and kernel. If the controller
and kernel support extended advertising, we include flags indicating
hardware offloading support and support for setting tx power of adv
instances.
In the future, vendor-specific commands may allow the setting of tx
power in advertising instances, but for now this feature is only
marked available if extended advertising is supported.
This change is manually verified in userspace by ensuring the
advertising manager's supported_flags field is updated with new flags on
hatch chromebook (ext advertising supported).
Signed-off-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to enable the use of RPA Address resolution
using expermental feature mgmt command.
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enable RPA timeout during bluetooth initialization.
The RPA timeout value is used from hdev, which initialized from
debug_fs
Signed-off-by: Sathish Narasimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the LL Privacy support is available, then as part of enabling or
disabling passive background scanning, it is required to set up the
controller based address resolution as well.
Since only passive background scanning is utilizing the whitelist, the
address resolution is now bound to the whitelist and passive background
scanning. All other resolution can be easily done by the host stack.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using controller based address resolution, then the new address
types 0x02 and 0x03 are used. These types need to be converted back into
either public address or random address types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For some reason they tend to squat on the very first CSR/
Cambridge Silicon Radio VID/PID instead of paying fees.
This is an extremely common problem; the issue goes as back as 2013
and these devices are only getting more popular, even rebranded by
reputable vendors and sold by retailers everywhere.
So, at this point in time there are hundreds of modern dongles reusing
the ID of what originally was an early Bluetooth 1.1 controller.
Linux is the only place where they don't work due to spotty checks
in our detection code. It only covered a minimum subset.
So what's the big idea? Take advantage of the fact that all CSR
chips report the same internal version as both the LMP sub-version and
HCI revision number. It always matches, couple that with the manufacturer
code, that rarely lies, and we now have a good idea of who is who.
Additionally, by compiling a list of user-reported HCI/lsusb dumps, and
searching around for legit CSR dongles in similar product ranges we can
find what CSR BlueCore firmware supported which Bluetooth versions.
That way we can narrow down ranges of fakes for each of them.
e.g. Real CSR dongles with LMP subversion 0x73 are old enough that
support BT 1.1 only; so it's a dead giveaway when some
third-party BT 4.0 dongle reuses it.
So, to sum things up; there are multiple classes of fake controllers
reusing the same 0A12:0001 VID/PID. This has been broken for a while.
Known 'fake' bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
IC markings on 0x7558: FR3191AHAL 749H15143 (???)
https://bugzilla.kernel.org/show_bug.cgi?id=60824
Fixes: 81cac64ba2 (Deal with USB devices that are faking CSR vendor)
Reported-by: Michał Wiśniewski <brylozketrzyn@gmail.com>
Tested-by: Mike Johnson <yuyuyak@gmail.com>
Tested-by: Ricardo Rodrigues <ekatonb@gmail.com>
Tested-by: M.Hanny Sabbagh <mhsabbagh@outlook.com>
Tested-by: Oussama BEN BRAHIM <b.brahim.oussama@gmail.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Starting with the upgrade to v5.8-rc3, I've noticed I wasn't able to
connect to my Bluetooth headset properly anymore. While connecting to
the device would eventually succeed, bluetoothd seemed to be confused
about the current connection state where the state was flapping hence
and forth. Bisecting this issue led to commit 3ca44c16b0 (Bluetooth:
Consolidate encryption handling in hci_encrypt_cfm, 2020-05-19), which
refactored `hci_encrypt_cfm` to also handle updating the connection
state.
The commit in question changed the code to call `hci_connect_cfm` inside
`hci_encrypt_cfm` and to change the connection state. But with the
conversion, we now only update the connection state if a status was set
already. In fact, the reverse should be true: the status should be
updated if no status is yet set. So let's fix the isuse by reversing the
condition.
Fixes: 3ca44c16b0 ("Bluetooth: Consolidate encryption handling in hci_encrypt_cfm")
Signed-off-by: Patrick Steinhardt <ps@pks.im>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the extended advertisement feature is enabled, a hardcoded min and
max interval of 0x8000 is used. This patch fixes this issue by using
the configured min/max value.
This was validated by setting min/max in main.conf and making sure the
right setting is applied:
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen
25 #93 [hci0] 10.953011
…
Min advertising interval: 181.250 msec (0x0122)
Max advertising interval: 181.250 msec (0x0122)
…
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Daniel Winkler <danielwinkler@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If user decides to cancel the ongoing pairing process (e.g. by clicking
the cancel button on pairing/passkey window), abort any ongoing pairing
and then terminate the link if it was created because of the pair
device action.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This calls hci_update_background_scan() when there is any update on the
advertisement monitors. If there is at least one advertisement monitor,
the filtering policy of scan parameters should be 0x00. This also reports
device found mgmt events if there is at least one monitor.
The following cases were tested with btmgmt advmon-* commands.
(1) add a ADV monitor and observe that the passive scanning is
triggered.
(2) remove the last ADV monitor and observe that the passive scanning is
terminated.
(3) with a LE peripheral paired, repeat (1) and observe the passive
scanning continues.
(4) with a LE peripheral paired, repeat (2) and observe the passive
scanning continues.
(5) with a ADV monitor, suspend/resume the host and observe the passive
scanning continues.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_REMOVE_ADV_MONITOR command.
Note that the controller-based monitoring is not yet in place. This
removes the internal monitor(s) without sending HCI traffic, so the
request returns immediately.
The following test was performed.
- Issue btmgmt advmon-remove with valid and invalid handles.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_ADD_ADV_PATTERNS_MONITOR command.
Note that the controller-based monitoring is not yet in place. This tracks
the content of the monitor without sending HCI traffic, so the request
returns immediately.
The following manual test was performed.
- Issue btmgmt advmon-add with valid and invalid inputs.
- Issue btmgmt advmon-add more the allowed number of monitors.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds the request handler of MGMT_OP_READ_ADV_MONITOR_FEATURES
command. Since the controller-based monitoring is not yet in place, this
report only the supported features but not the enabled features.
The following test was performed.
- Issuing btmgmt advmon-features.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Replace the wakeable boolean with flags in hci_conn_params and all users
of this boolean. This will be used by the get/set device flags mgmt op.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the classic device list now supports flags, convert the wakeable
list into a flag on the existing device list.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to more easily add device flags to classic devices, create
a new type of bdaddr_list that supports setting flags.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch centralized the initialization of default parameters. This
is required to allow clients to more easily customize the default
system parameters.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch submits the corresponding kernel definitions to mgmt.h.
This is submitted before the implementation to avoid any conflicts in
values allocations.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Yu Liu <yudiliu@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change implements suggestions from the code review of the SCO CMSG
state flag patch.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change adds support for reporting the BT_PKT_STATUS to the socket
CMSG data to allow the implementation of a packet loss correction on
erroneous data received on the SCO socket.
The patch was partially developed by Marcel Holtmann and validated by
Hsin-yu Chao.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes hci_encrypt_cfm calls hci_connect_cfm in case the connection
state is BT_CONFIG so callers don't have to check the state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Let drivers have a hook to disable configuring scanning during suspend.
Drivers should use the device_may_wakeup function call to determine
whether hci should be configured for wakeup.
For example, an implementation for btusb may look like the following:
bool btusb_prevent_wake(struct hci_dev *hdev)
{
struct btusb_data *data = hci_get_drvdata(hdev);
return !device_may_wakeup(&data->udev->dev);
}
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Renamed BT_SUSPEND_COMPLETE to BT_SUSPEND_CONFIGURE_WAKE since it sets
up the event filter and whitelist for wake-up.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case dynamic debug is disabled, this feature allows a vendor platform
to provide debug statement printing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To enable platform specific experimental features, introduce this new set of
management commands and events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When setting HCI_MGMT_HDEV_OPTIONAL it is possible to target a specific
conntroller or a global interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
