Since there is a helper function, use it to help readability.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
It'd be safer to enable both FIFOs for TX or RX at the same time.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleans fsl_ssi_setup_regvals() by following changes:
1) Moving DBG bits to the first lines.
2) Setting SSIE, RE/TE as default and cleaning it for AC97
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The _fsl_ssi_set_dai_fmt() bypasses an undefined format for AC97
mode. However, it's not really necessary if AC97 has its complete
format defined.
So this patch adds a DAIFMT macro of complete format including a
clock direction and polarity.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The trigger() calls fsl_ssi_tx_config() and fsl_ssi_rx_config(),
and both of them jump to fsl_ssi_config(). And fsl_ssi_config()
later calls another fsl_ssi_rxtx_config().
However, the whole routine, especially fsl_ssi_config() function,
is too complicated because of the folowing reasons:
1) It has to handle the concern of the opposite stream.
2) It has to handle cases of offline configurations support.
3) It has to handle enable and disable operations while they're
mostly different.
Since the enable and disable routines have more differences than
TX and RX rountines, this patch simplifies these helper functions
with the following changes:
- Changing to two helper functions of enable and disable instead
of TX and RX.
- Removing fsl_ssi_rxtx_config() by separately integrating it to
two newly introduced enable & disable functions.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FIFO clear helper function is just one line of code now.
So it could be cleaned up by removing it and calling regmap
directly.
Meanwhile, FIFO clear could be applied to all use cases, not
confined to AC97. So this patch also moves FIFO clear in the
trigger() to fsl_ssi_config() and removes the AC97 check.
Note that SOR register is safe from offline_config HW limit.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The define of fsl_ssi_disable_val is not so clear as it mixes two
steps of calculations together. And those parameter names are also
a bit long to read.
Since it just tries to exclude the shared bits from the regvals of
current stream while the opposite stream is active, it's better to
use something like ssi_excl_shared_bits.
This patch also bisects fsl_ssi_disable_val into two macros of two
corresponding steps and then shortens its parameter names. It also
updates callers in the fsl_ssi_config() accordingly.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Checking TE and RE bits in SCR register doesn't work for AC97 mode
which enables SSIEN, TE and RE in the fsl_ssi_setup_ac97() that's
called during probe().
So when running into the trigger(), it will always get the result
of both TE and RE being enabled already, even if actually there is
no active stream.
This patch fixes this issue by adding a variable to log the active
streams manually.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch replaces the register read with ssi->i2s_net for
simplification. It also removes masking SSIEN from scr value
since it's handled later by regmap_update_bits() to set this
scr value back.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hw_params() overwrites i2s_net settings for special cases like
mono-channel support, however, it doesn't update ssi->i2s_net as
set_dai_fmt() does.
This patch removes the local i2s_net variable and directly updates
ssi->i2s_net in the hw_params() so that the driver can simply look
up the ssi->i2s_net instead of reading the register.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The RX and TX macros were defined implicitly and there was
a potential risk if someone changes their values.
Since they were defined to index the array ssi->regvals[2],
this patch moves these two macros to fsl_ssi.c, closer to
its owner ssi->regvals. And it also puts some comments here
to limit their value within [0, 1].
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'iprop' variable is passed as an argument to the be32_to_cpup()
function, which expects a 'const _be *' type.
Change the iprop variable type so that the following build warnings
with W=1 are gone:
sound/soc/fsl/fsl_ssi.c:1463:48: warning: incorrect type in argument 1 (different base types)
sound/soc/fsl/fsl_ssi.c:1463:48: expected restricted __be32 const [usertype] *p
sound/soc/fsl/fsl_ssi.c:1463:48: got unsigned int const [usertype] *[assigned] iprop
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
powerpc:mpc85xx_defconfig fails to build with the following errors.
sound/soc/fsl/fsl_dma.c: In function 'fsl_soc_dma_probe':
sound/soc/fsl/fsl_dma.c:916:34: error: 'CCSR_SSI_STX0' undeclared
sound/soc/fsl/fsl_dma.c:917:34: error: 'CCSR_SSI_SRX0' undeclared
Fixes: a818aa5f96 ("ASoC: fsl_ssi: Rename registers and fields macros")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regmap code looks redudant. So simplify it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since this i2smode also includes the setting of Network mode, it
should have it in the name. This patch also adds its MASK define.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The name fsl_ssi_rxtx_reg_val is too long to read comfortably.
So this patch shortens it by using an array (fsl_ssi_regvals,
renamed from fsl_ssi_reg_val). To do that, it also introduces
two macros (TX and RX) to replace the wrapper structure. This
will also help further cleanups.
Meanwhile, it unifies all local variable with the name "vals"
to get rid of the name "reg" -- could be confusing with "regs"
in the private struct for regmap.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify the variable name. This reduces one over-80-character line.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shortens the variable name to save space, useful for dev_err outputs.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patches unifies the error message in the "failed to xxxx" format.
It also reduces the length of one line and adds spaces to an operator.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch just simply unifies the coding style.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch renames CCSR_SSI_xxx to REG_SSI_xxx and SSI_xxx_yyy style.
It also slightly reduces the length of them to save some space.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch refines the comments by:
1) Removing all out-of-date comments
2) Removing all not-so-useful comments
3) Unifying the styles of all comments
4) Shortening comments to be more conise
5) Adding comments to improve code readablity
6) Moving all register related comments to fsl_ssi.h
7) Adding comments to all register and field defines
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There should be no trouble to understand dev = pdev->dev.
This can save some space to have more print info or save
some wrapped lines.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Shorten the private data structure to save some wrapped lines.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Protect macro argument with parentheses to avoid ambiguity.
This fixes a warning seen with clang:
warning: logical not is only applied to the left hand side of this comparison
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rtd->codec will be removed soon.
rtd->codec = rtd->codec_dai->codec, thus,
we can use rtd->codec_dai->component instead of it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The machine driver links both imx-ssi (legacy non-DT driver) and
fsl_ssi (up-to-date DT based driver). So It also includes both
imx-ssi.h and fsl_ssi.h header files. This creates a limitation
for two header files -- they can't define anything with identical
names.
Since the eukrea-tlv320 machine driver now does not really need
anything being defined in the fsl_ssi header file, and it's also
going to take some time to clean up two SSI drivers, this patch
takes a quick way to remove the #include fsl_ssi.h line for now.
It can be added back once the header files are done refactoring.
The eukrea-tlv320 driver is still compiled successfully without
any erorr using imx_v6_v7_defconfig, after removing it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When testing AC'97 capture on UDOO board (currently the only user of
fsl_ssi driver in the AC'97 mode) it become obvious that there is a massive
distortion above certain, small input signal.
This problem has been traced to silicon errata ERR003778:
"In AC97, 16-bit mode, received data is shifted by 4-bit locations" that
has "No fix scheduled".
This errata suggests a workaround of doing a 4-bit shift back in SDMA
script for this specific operation mode, however our SDMA scripts are
shared between various SoC peripherals so we can't really modify them.
There is a simple way to avoid this problem, however, that is to disallow
recording in 16-bit mode and only support it in AC'97-native 20-bit mode.
We have to use a 4-byte format for this since SSI FIFOs do not allow 3-byte
accesses (and these aren't supported by imx-sdma driver anyway).
With this change the capture distortion is gone.
We can also add this format as an additional one supported for playback,
using this opportunity to make sure that we use CPU-endian-native formats
in AC'97 mode as we already do in I2S mode.
There is no problem in using different bit widths in playback and capture
in AC'97 mode so allow this, too.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASRFSTi_IAEi has an 11-bit offset as its _SHIFT macro defines.
So this patch just fixes that.
Reported-by: Laurent Charpentier <laurent.charpentier@nxp.com>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to make sure that only proper channel slots (in SACCST register)
are enabled at playback start time since some AC'97 CODECs (like VT1613 on
UDOO board) were observed requesting via SLOTREQ spurious ones just after
an AC'97 link is started but before the CODEC is configured by its driver.
When a bit for some channel slot is set in a SLOTREQ request then SSI sets
the relevant bit in SACCST automatically, which then 'sticks' until it is
manually unset.
The SACCST register is not writable directly, we have to use SACCDIS and
SACCEN registers to configure it instead (these aren't normal registers:
writing a '1' bit at some position in SACCEN sets the relevant bit in
SACCST; SACCDIS operates in a similar way but allows unsetting bits in
SACCST).
Theoretically, this should be necessary only for the very first playback
but since some CODECs are so untrustworthy and extra channel slots enabled
mean ruined playback let's play safe here and make sure that no extra
slots are enabled in SACCST every time a playback is started.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In AC'97 mode we configure and start SSI RX / TX on probe path via
a call to _fsl_ssi_set_dai_fmt() function.
We don't need to call this function again later and in fact don't want to
do it since this function temporarily sets STCR, SRCR and SCR to some
intermediate values.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need to set CCSR_SSI_SIER_RFF0_EN / CCSR_SSI_SIER_TFE0_EN bits
in reg->rx.sier / reg->tx.sier variables in a non-AC'97 mode considering we
had just initialized these variables to these very values unconditionally a
few lines earlier.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC'97 register access operations (both read and write) on SSI use a one,
shared set of SSI registers for AC'97 register address and data.
This means that only one such access is possible at a time and so all these
operations need to be serialized.
Since an AC'97 register access operation in this driver takes 100us+ let's
use a mutex for this.
Use this opportunity to also change a default value returned from AC'97
register read function from -1 to 0, since that's what AC'97 specs require
to be returned when unknown / undefined registers are read.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC'97 ops (register read / write) need SSI regmap and clock, so they have
to be set after them.
We also need to set these ops back to NULL if we fail the probe.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_component_set_sysclk() and snd_soc_dai_set_tdm_slot()
in the soc-core.c will return -ENOTSUPP if there is no function
implementation for them in the dai and component drivers.
So this patch tries to ignore this errno.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The set_sysclk() now is used to override the output bit clock rate.
But this is not a common way to implement a set_dai_sysclk(). And
this creates a problem when a general machine driver (simple-card
for example) tries to do set_dai_sysclk() by passing an input clock
rate for the baud clock instead of setting the bit clock rate as
fsl_ssi driver expected.
So this patch solves this problem by firstly removing set_sysclk()
since the hw_params() can calculate the bit clock rate. Secondly,
in order not to break those TDM use cases which previously might
have been using set_sysclk() to override the bit clock rate, this
patch changes the driver to calculate the bit clock rate using the
slot number and the slot width from the via set_tdm_slot().
The patch also removes an obsolete comment of the dir parameter.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the const arrays rate on the stack, instead make them
static. Makes the object code smaller by 220 bytes:
Before:
text data bss dec hex filename
24385 9776 128 34289 85f1 sound/soc/fsl/fsl_spdif.o
After:
text data bss dec hex filename
24005 9936 128 34069 8515 sound/soc/fsl/fsl_spdif.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_object.path is unused, so rather than fix it to work with DT
full_name changes, just remove it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Timur Tabi <timur@tabi.org>
Cc: Nicolin Chen <nicoleotsuka@gmail.com>
Cc: Xiubo Li <Xiubo.Lee@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: linuxppc-dev@lists.ozlabs.org
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since jack gpios are managed via devres, we don't have to call
snd_jack_free_gpios() at release any longer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Probe deferral is to be expected during normal operation, so avoid
printing an error when it is encountered.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make these const as they are only passed as the 2nd argument to the
function snd_soc_set_runtime_hwparams, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make these const as they are only passed as the 2nd argument to the function
snd_soc_register_platform, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
