The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Stephen Warren <swarren@nvidia.com>
CC: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com> (for ocores and mux-gpio)
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com> (for i2c-gpio)
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> (for puf3)
Acked-by: Barry Song <baohua.song@csr.com> (for sirf)
Reviewed-by: Jean Delvare <khali@linux-fr.org>
[wsa: Fixed "foo* bar" flaws while we are here]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
We have several new drivers, most of the time coming with their sub devices
drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ
APIs and a conversion to the recently added PWM framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have Mark's
wm5xxx and wm8xxx patchset.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQznPnAAoJEIqAPN1PVmxKuA8P/0nOJduXFM1c0Gy+DD5DnJnG
cXzzeSTV8iO3a3sHIye43QPJ5V2YUR5uxLTUEOo/G7my/MoZ/azeNidkUD3qLVlm
wVIq35lcS8dWTZaY7nlpBcWc6e39UB0sEueuJNxyhOv5lnMKdi2tAow5f4vIRQnd
Q67/EbrgqdltcOpGmVuCdQcvphvWgy+K65jzbJG5zXs7hGX13Q+M5RnYhx76kc8f
TDd0APZ71n5/RyISFSBSu2vfl2kES6o47aMgqqXMEHri6d3puAaXM0rFoMzXg/4G
eBdxndN25H7rW7xvt9tuUod2rn1AO7tif5d7jal3Cfj61y3iqKY30yb3OzS9XQXH
9WZ2qDst11zvzQivxIkMGvfRXRfncNLWR4DrBSqVfSbYV2uQj2eS8C6ONwKVMXsQ
5tjNp91PFqN19sWQjIjSMcrNswxgpvdQ9mqFTyOGmISbqrpPSTi+MuO8r9+xTfUF
PnzUX2nVOW/i9NcI7uotjzh8jiw6t8XMVHhkehiSYR9hzCb6MaPsFPN4jWq9XA2m
1htCHylNpHqHQ3Mup7Is6j0Li1ahdwfm4lbrgiVEA4t4Mqs5E/Ka+3V8laNAKylW
PfCP/VmnJYzmgVTK/qobFNeKzRqR0i4WTL6T7oAxGL87Q4TJaqKpEkXWne8UXV+Q
yIbN0fmWfCveCetM+vaf
=F790
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I did not receive a single bug report after interrupt support was
added for a limited number of chips. So I'd say the code is good and
should be enabled for all supported chips, that is: ICH5 and later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Add support for probing slave devices parsed from the device tree.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to be
part of the multiplatform support -- the first "big" SoC that is moved
over (more multiplatform work comes in a separate branch later during
the merge window).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zfPd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
* Introduction of device PM QoS flags.
* ACPI device power management update allowing subsystems other than
PCI to use it more easily.
* ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
* ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
* ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
* Introduction of acpi_handle_<level>() messaging macros and ACPI-based CPU
hot-remove support from Toshi Kani.
* ACPI EC updates from Feng Tang.
* cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
* cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
* Support for using multiple cpuidle drivers at the same time and cpuidle
cleanups from Daniel Lezcano.
* devfreq updates from Nishanth Menon and others.
* cpupower update from Thomas Renninger.
* Fixes and small cleanups all over the place.
--
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQxxevAAoJEKhOf7ml8uNsHacQAK2xoQozDddPBAaTCf1OWW/G
J4E2qMn+gy4AtFmQ0/xeZVvvylOCn9eu/kv3QJ/bFlVoUsqTgfPwQBjT6HjF1Acn
7yVFdr9H/tn2wi9nW2Gv6Tl2Hr/kFLpo0f5Kd40Z+P8SV5sKX5ktJcVpJ/I/P4Vh
Qw2nWtj7hQktZDERzgG4ZpMbQToNhbLhbKWB9ad3/XQSSA9JkfgvBFgrTEGHcZD5
bwsggjNdOAWNGeDdzRsQSDn0Alld5ILVdSJ5xKimO1O70WvKc7fqA1IdYRIeKL90
yz4bcoYKzl9iktlw8+x5o1U9mrc8TFV5p4+zV+t5Z6pzS/J3kWvnsW4zu9sCrxFv
Wic3SKyiem7s2dxrYyj4ZXAci3GK4ouRTrCLqk7/00tEGdwAQD1ZNfsUJp6jKayz
FvtZUgItcOyrlQ6B4nh951OY6dI3AUYJ2NuWWNr5NZkgVAvQGV8zTGOImbeVeL2+
pMiw14zScO3ylYilVcjTKDDMj2sDZ68mw5PIcbmksvWsCLo26jDBVDtLVmtYWyd4
ek3WnOrQZr0R3agvOLLssMKXompvpP+N4Klf4rV+GtqGsWtHryYKys2Laju9FwFj
yYLchxYlxhGTzqq8LjF90HDL0TWpPe6cPi+B5ow9g/SXLexbMKNQGhv3Jovm2yR3
j54tKBWy7e9AAYEDPirX
=6OEP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Introduction of device PM QoS flags.
- ACPI device power management update allowing subsystems other than
PCI to use it more easily.
- ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
- ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
- ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
- Introduction of acpi_handle_<level>() messaging macros and ACPI-based
CPU hot-remove support from Toshi Kani.
- ACPI EC updates from Feng Tang.
- cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
- cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
- Support for using multiple cpuidle drivers at the same time and
cpuidle cleanups from Daniel Lezcano.
- devfreq updates from Nishanth Menon and others.
- cpupower update from Thomas Renninger.
- Fixes and small cleanups all over the place.
* tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (196 commits)
mmc: sdhci-acpi: enable runtime-pm for device HID INT33C6
ACPI: add Haswell LPSS devices to acpi_platform_device_ids list
ACPI: add documentation about ACPI 5 enumeration
pnpacpi: fix incorrect TEST_ALPHA() test
ACPI / PM: Fix header of acpi_dev_pm_detach() in acpi.h
ACPI / video: ignore BIOS initial backlight value for HP Folio 13-2000
ACPI : do not use Lid and Sleep button for S5 wakeup
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
spi / ACPI: add ACPI enumeration support
gpio / ACPI: add ACPI support
PM / devfreq: remove compiler error with module governors (2)
cpupower: IvyBridge (0x3a and 0x3e models) support
cpupower: Provide -c param for cpupower monitor to schedule process on all cores
cpupower tools: Fix warning and a bug with the cpu package count
cpupower tools: Fix malloc of cpu_info structure
cpupower tools: Fix issues with sysfs_topology_read_file
cpupower tools: Fix minor warnings
cpupower tools: Update .gitignore for files created in the debug directories
...
Bug fixes, little cleanups, and documentation changes. The most invasive
thing here touches a bunch of the arch directories to use a common build
rule for .dtb files. There are no major changes to functionality here
other than a ew new helper functions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LB3n
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull device tree changes from Grant Likely:
"Here are the DT changes I've got queued up for v3.8. As described
below, there are a lot of bug fixes here and documentation updates but
nothing major:
Bug fixes, little cleanups, and documentation changes. The most
invasive thing here touches a bunch of the arch directories to use a
common build rule for .dtb files. There are no major changes to
functionality here other than a few new helper functions."
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
arm64: Fix the dtbs target building
mtd: nand: davinci: fix the binding documentation
rtc: rtc-mv: Add the device tree binding documentation
devicetree/bindings: Move gpio-leds binding into leds directory
of/vendor-prefixes: add Imagination Technologies
microblaze: use new common dtc rule
c6x: use new common dtc rule
openrisc: use new common dtc rule
arm64: Add dtbs target for building all the enabled dtb files
arm64: use new common dtc rule
ARM: dt: change .dtb build rules to build in dts directory
kbuild: centralize .dts->.dtb rule
Fix build when CONFIG_W1_MASTER_GPIO=m b exporting "allnodes"
of/spi: Honour "status=disabled" property of device
of_mdio: Honour "status=disabled" property of device
of_i2c: Honour "status=disabled" property of device
powerpc: Fix fallout from device_node->name constification
of: add 'const' for of_parse_phandle parameter *np
Documentation: correct of_platform_populate() argument list
script: dtc: clean generated files
...
The OMAP_I2C_FLAG_RESET_REGS_POSTIDLE is not used anymore
in the i2c driver. Remove the flag.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Add dma support for Atmel TWI which is available on sam9x5 and later.
When using dma for reception, you have to read only n-2 bytes. The last
two bytes are read manually. Don't doing this should cause to send the
STOP command too late and then to get extra data in the receive
register.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Replace tabs for struct members indentation by space to minimise line changes
when adding new members which would require extra tabs to keep alignment.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch fixes the following warning:
drivers/i2c/busses/i2c-at91.c: In function ‘at91_twi_get_driver_data’:
drivers/i2c/busses/i2c-at91.c:411:3: warning: return discards ‘const’ qualifier from pointer target type [enabled by default]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
ACPI 5 introduced I2cSerialBus resource that makes it possible to enumerate
and configure the I2C slave devices behind the I2C controller. This patch
adds helper functions to support I2C slave enumeration.
An ACPI enabled I2C controller driver only needs to call acpi_i2c_register_devices()
in order to get its slave devices enumerated, created and bound to the
corresponding ACPI handle.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Properly terminate the DMA transfer in case the DMA PIO transfer
or setup fails for any reason.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
There is no reason to disable the I2C SMBus quick mode on this
IP block. Enable it. This essentially fixes the problem with the
"i2c-detect" command for probing the bus.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Properly terminate the DMA transfer in case the DMA PIO transfer
or setup fails for any reason.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The changes in "i2c-s3c2410: use exponential back off while polling for
bus idle" remove the initial busy wait for I2C transfers to complete and
replace it with usleep_range() calls which will schedule.
Since for older SoCs I2C transfers would usually complete within an
extremely small number of CPU cycles there is a win from not having to
schedule. This happens because on the older SoCs the cores run at a
smaller multiple of the speeds that the I2C bus is operating at; on more
modern SoCs the busy wait is less likely to be effective.
Fix the issue by restoring the busy wait, reducing the number of spins
from 20 to 3 which covers the overwhelming majority of I2C transfers on
the SoCs where the busy wait is effective.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This moves the grlib set and get functions into the #ifdef CONFIG_OF block to
avoid warnings of unimplemented functions when compiling with -Wunused-function
when CONFIG_OF is not defined.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This adds the mfd cell to use the i2c part of the Nano River Technologies
viperboard as i2c master.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
"Whether" is misspelled in various comments across the tree; this
fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Store the requested gpios so that they can be freed on error/removal.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The I2C driver makes a gpio_request during initialization. This request
happens again on resume and fails due to the earlier successful request.
Re-factor the code to only initialize the gpios during probe.
Errors on resume without this:
[ 16.020000] s3c-i2c s3c2440-i2c.0: gpio [42] request failed
[ 16.020000] s3c-i2c s3c2440-i2c.1: gpio [44] request failed
[ 16.020000] s3c-i2c s3c2440-i2c.2: gpio [6] request failed
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Store the requested gpios so that they can be freed on error/removal.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Add i2c driver to enable access to devices behind CBUS on Nokia Internet
Tablets.
The patch also adds CBUS I2C configuration for N8x0 which is one of the
users of this driver.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The registers in the GRLIB port of the controller are 32-bit and in big endian
byte order. The PRELOW and PREHIGH registers are merged into one register. The
subsequent registers have their offset decreased accordingly. Hence the register
access needs to be handled in a non-standard manner using custom getreg and
setreg functions.
Add setreg and getreg functions for different register widths and let oc_setreg
and oc_getreg use function pointers to call the appropriate functions.
A type is added as the data of the of match table entries. A new entry with a
different compatible string is added to the table. The type of that entry
triggers usage of the custom grlib functions by setting the setreg and getreg
function pointers.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Add sparc support by using platform_get_irq instead of platform_get_resource.
There are no platform resources of type IORESOURCE_IRQ for sparc, but
platform_get_irq works for sparc. In the non-sparc case platform_get_irq
internally uses platform_get_resource.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently we just queue the transfer and release the
qos constraints, however we do not wait for the transfer
to complete to release the constraint. Move the remove
constraint after the bus busy as we are sure that the
transfers are completed by then.
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Commit "i2c-s3c2410: Add HDMIPHY quirk for S3C2440" added support for
HDMIPHY with some special handling in s3c24xx_i2c_set_master:
"due to unknown reason (probably HW bug in HDMIPHY and/or the controller)
a transfer fails to finish. The controller hangs after sending the last
byte, the workaround for this bug is resetting the controller after each
transfer"
The "unknown reason" was that the proper sequence for generating a STOP
condition wasn't being followed as per the datasheet. Since this is fixed
by "PATCH: i2c-s3c2410: do not generate STOP for QUIRK_HDMIPHY buses",
remove the special handling.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Usually, the i2c controller has finished emitting the i2c STOP before the
driver reaches the bus idle polling loop. Optimize for this most common
case by reading IICSTAT first and potentially skipping the loop.
If the cpu is faster than the hardware, we wait for bus idle in a polling
loop. However, since the duration of one iteration of the loop is
dependent on cpu freq, and this i2c IP is used on many different systems,
use a time based loop timeout (5 ms).
We would like very low latencies to detect bus idle for the normal
'fast' case. However, if a device is slow to release the bus for some
reason, it could hold off the STOP generation for up to several
milliseconds. Rapidly polling for bus idle would seriously load the CPU
while waiting for it to release the bus. So, use a partial exponential
backoff as a compromise between idle detection latency and cpu load.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The datasheet says that the STOP sequence should be:
1) I2CSTAT.5 = 0 - Clear BUSY (or 'generate STOP')
2) I2CCON.4 = 0 - Clear IRQPEND
3) Wait until the stop condition takes effect.
4*) I2CSTAT.4 = 0 - Clear TXRXEN
Where, step "4*" is only for buses with the "HDMIPHY" quirk.
However, after much experimentation, it appears that:
a) normal buses automatically clear BUSY and transition from
Master->Slave when they complete generating a STOP condition.
Therefore, step (3) can be done in doxfer() by polling I2CCON.4
after starting the STOP generation here.
b) HDMIPHY bus does neither, so there is no way to do step 3.
There is no indication when this bus has finished generating STOP.
In fact, we have found that as soon as the IRQPEND bit is cleared in
step 2, the HDMIPHY bus generates the STOP condition, and then immediately
starts transferring another data byte, even though the bus is supposedly
stopped. This is presumably because the bus is still in "Master" mode,
and its BUSY bit is still set.
To avoid these extra post-STOP transactions on HDMI phy devices, we just
disable Serial Output on the bus (I2CSTAT.4 = 0) directly, instead of
first generating a proper STOP condition. This should float SDA & SCK
terminating the transfer. Subsequent transfers start with a proper START
condition, and proceed normally.
The HDMIPHY bus is an internal bus that always has exactly two devices,
the host as Master and the HDMIPHY device as the slave. Skipping the STOP
condition has been tested on this bus and works.
Also, since we disable the bus directly from the isr, we can skip the bus
idle polling loop at the end of doxfer().
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
We probably don't want to change I2C frequency while a transfer is in
progress. The current implementation grabs a spinlock, but that only
protected the writes to IICCON when starting a message, it didn't protect
against clock changes in the middle of a transaction.
Note: The i2c-core already grabs the adapter lock before calling
s3c24xx_i2c_doxfer(), which ensures that only one caller is issuing a
xfer at a time. This means it is not necessary to disable interrupts
(spin_lock_irqsave) when changing frequencies, since there won't be
any i2c interrupts if there is no on-going xfer.
Lastly, i2c_lock_adapter() may cause the cpufreq_transition to sleep if
if a xfer is in progress, but this is ok since cpufreq notifiers are
called in a kernel thread, and there are already cases where it could
sleep, such as when using i2c to update the output of a voltage
regulator.
Note: the cpufreq part of this change has no functional affect on
exynos, where the i2c clock is independent of the cpufreq.
But, there is a slight perfomance boost since we no longer need to
lock/unlock an additional spinlock.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch adds support for pin configuration using pinctrl subsystem
to the i2c-s3c2410 driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
A small code saving and less error handling to worry about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Use the PM_SLEEP ifdef for system suspend and resume. This is partly
in preparation for adding runtime operations and partly because a user
may in theory choose to enable runtime suspend but not system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Allow the i2c-mux-gpio to be used by a device tree enabled device. The
bindings are inspired by the one found in the i2c-mux-pinctrl driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
[wsa: fixed some whitespace]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Ensure that any of preceding register write operations to the I2C
hardware block reached the module, and the write data is reflected
in the registers, before leaving the interrupt handler.
Otherwise, we'll suffer from spurious WAIT interrupts that lead to
'Transfer request timed out' message, and the transaction failed.
Reported-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
On newer SH-/R-Mobile SoCs, a clock supply to the I2C hardware block,
which is used to generate the SCL clock output, is getting faster than
before, while on the other hand, the SCL clock control registers, ICCH
and ICCL, stay unchanged in 9-bit-wide (8+1).
On such silicons, the internal SCL clock counter gets incremented every
2 clocks of the operating clock.
This patch makes it configurable through platform data.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
ICCH/ICCL values is supposed to be calculated/optimized to strictly meet
the timing specs required by the I2C standard. The resulting I2C bus
speed does not matter at all, if it's less than 100 or 400 kHz.
With this change, sh_mobile_i2c_icch() is virtually identical to
sh_mobile_i2c_iccl(), but they're providing good descriptions of
SH-/R-Mobile I2C hardware spec, and I'd leave them as separated.
Also fix a typo in the comment, print icch/iccl values at probe, etc.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
[wsa: squashed two patches for bisectability]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently SCL clock parameters (ICCH/ICCL) are calculated in
activate_ch(), which gets called every time sh_mobile_i2c_xfer() is
processed, while each I2C bus speed is system-defined and in general
those parameters do not have to be updated over I2C transactions.
The only reason I could see having it transaction-time is to adjust
ICCH/ICCL values according to the operating frequency of the I2C
hardware block, in the face of DFS (Dynamic Frequency Scaling).
However, this won't be necessary.
The operating frequency of the I2C hardware block can change _even_
in the middle of I2C transactions. There is no way to prevent it
from happening, and I2C hardware block can work with such dynamic
frequency change, of course.
Another is that ICCH/ICCL clock parameters optimized for the faster
operating frequency, can also be applied to the slower operating
frequency, as long as slave devices work. However, the converse is
not true. It would violate SCL timing specs of the I2C standard.
What we can do now is to calculate the ICCH/ICCL clock parameters
according to the fastest operating clock of the I2C hardware block.
And if that's the case, that calculation should be done just once
at driver-module-init time.
This patch moves ICCH/ICCL calculating part from activate_ch() into
sh_mobile_i2c_init(), and call it from sh_mobile_i2c_probe().
Note that sh_mobile_i2c_init() just prepares clock parameters using
the clock rate and platform data provided, but does _not_ make any
hardware I/O accesses. We don't have to care about run-time PM
maintenance here.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Filenames of devictree binding documentation seems to be arbitrary and
for me it is unneeded hazzle to find the corresponding documentation for
a specific driver.
Naming the description the same as the driver is a lot easier and makes
sense to me since the driver defines the binding it understands.
Also, remove a reference in one source to the binding documentation, since path
information easily gets stale.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently after the reset the sysc is written with hardcoded values.
The patch reads the sysc register and writes back the same value
after reset.
- Some unnecessary rev checks can be optimised.
- Also due to whatever reason the hwmod flags are changed
we will not reset the values.
- In some of the cases the minor values of the 2430 register
is different(0x37) in that case the autoidle setting may be missed.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently the restore is done based on the flag
OMAP_I2C_FLAG_RESET_REGS_POSTIDLE.
This helps the following
- The driver is always capable of restoring regardless
of the off mode support being there or not.
- While testing omap2430 it is found that in case of certain
error paths (timeout) a reset is done. However the restore
never happens as it is dependent on the POSTIDLE flag.
The other option would be to call a restore in the reset
case. As there are only a few registers to be restored
the penalty in the idle case should not be much.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
