* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
The RX-51 uses the CSIb IO complex for camera operation. The
board file is missing definition for the regulator supplying
the CSIb complex, so this is added for better power
management.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
The vaux2 (VCSI) regulator is left on by the bootloader
in rx-51. Since there the product has shipped and there
won't be any bootloader updates to fix this issue, we
need to define all the regulators and declare full
constraints for the regulator FW. This will allow the
regulator FW to disable unused regulators.
Also this helps in adding more fine grain regulator
support for rx-51 in the future.
Thanks for Mark Brown for pointing out the correct
solution.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Platform support for lp5523 led chip
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allign the platform data names for twl4030 audio submodule:
twl4030_audio_data: for the core MFD driver
twl4030_codec_data: for ASoC codec driver
twl4030_vibra_data: for the input/ForceFeedback driver
To avoid breakage, change all depending drivers, files
to use the new types.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Some regulator config can be moved out from board files,
since they are close to identical.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reduce the amount of duplicated code by moving the common
configuration for twl4030/5030/tpsxx to the twl-common file.
Use the omap3_pmic_get_config function from board files to
properly configure the PMIC with the common fields.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Pointers to statically declared platform device structures which are
registered with platform_device_register() are then used during run time
to access these structure members, for example from platform_uevent()
and much more. Therefore, these structures should never be placed inside
sections which are dropped after boot. Fix platform devices incorrectly
tagged with __initdata which happen to exist inside OMAP sub-trees.
This bug has exhibited itself on my ARM/OMAP1 based Amstrad Delta
videophone after commit 6d3163ce86, "mm:
check if any page in a pageblock is reserved before marking it
MIGRATE_RESERVE", resulting in reading from several
/sys/device/platform/*/uevent files always ending up with segmentation
faults.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Varadarajan, Charulatha <charu@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
to use REGULATOR_SUPPLY arrays.
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: Mike Rapoport <mike@compulab.co.il>
CC: Nishant Kamat <nskamat@ti.com>
CC: Steve Sakoman <steve@sakoman.com>
CC: Felipe Balbi <balbi@ti.com>
CC: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: peter.barada@logicpd.com
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Speaker amplifier is accidentally powered up in early TWL gpio setup. This
causes a few mA of needless battery current consumption. Without this patch
the amplifier can be shutdown only by having one active audio playback and
shutdown cycle to speaker output.
Thanks to Kalle Jokiniemi <kalle.jokiniemi@nokia.com> for noticing the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The V28_A domain in Nokia N900 that supplies VDD voltages to TLV320AIC34 and
TPA6130A2 should not be shutdown. This is because otherwise there will be
leak from VIO to VDD in TLV320AIC34 and this leak consumes more battery
current that is saved from keeping V28_A off. With this patch the battery
current consumption is approximately 1.5 mA lower.
Thanks to Kalle Jokiniemi <kalle.jokiniemi@nokia.com> for noticing the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.infradead.org/battery-2.6:
PXA: Use dev_pm_ops in z2_battery
ds2760_battery: Fix rated capacity of the hx4700 1800mAh battery
ds2760_battery: Fix indexing of the 4 active full EEPROM registers
power: Make test_power driver more dynamic.
bq27x00_battery: Name of cycle count property
max8903_charger: Add GENERIC_HARDIRQS as a dependency (fixes S390 build)
ARM: RX-51: Enable isp1704 power on/off
isp1704_charger: Allow board specific powering routine
gpio-charger: Add gpio_charger_resume
power_supply: Add driver for MAX8903 charger
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (57 commits)
regulator: Fix 88pm8607.c printk format warning
input: Add support for Qualcomm PMIC8XXX power key
input: Add Qualcomm pm8xxx keypad controller driver
mfd: Add omap-usbhs runtime PM support
mfd: Fix ASIC3 SD Host Controller Configuration size
mfd: Fix omap_usbhs_alloc_children error handling
mfd: Fix omap usbhs crash when rmmoding ehci or ohci
mfd: Add ASIC3 LED support
leds: Add ASIC3 LED support
mfd: Update twl4030-code maintainer e-mail address
mfd: Correct the name and bitmask for ab8500-gpadc BTempPullUp
mfd: Add manual ab8500-gpadc batt temp activation for AB8500 3.0
mfd: Provide ab8500-core enumerators for chip cuts
mfd: Check twl4030-power remove script error condition after i2cwrite
mfd: Fix twl6030 irq definitions
mfd: Add phoenix lite (twl6025) support to twl6030
mfd: Avoid to use constraint name in 88pm860x regulator driver
mfd: Remove checking on max8925 regulator[0]
mfd: Remove unused parameter from 88pm860x API
mfd: Avoid to allocate 88pm860x static platform data
...
Modifying the macro name Main_Ref to all caps(MAIN_REF).
Suggested by Nishanth Menon <nm@ti.com>
Signed-off-by: Lesly A M <leslyam@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: David Derrick <dderrick@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
use gpio_request_<one|array>() instead of multiple gpiolib calls,
remove unneeded variables, etc.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduce omap_pmic_init that registers i2c bus and PMIC device on that
bus and add omap2/3/4 wrappers for common cases.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The isp1704 usb tranceiver is used for charging and can be
disabled when not in use. Provide the powering routine to
the driver via platform data.
Also changed the indent of ".name" variable in rx51_charger_device
definition to use tabs same way as the new ".dev" variable indent.
Put this in the same patch since the indent fix is only needed
when there are multiple members in the struct definition.
Loosely based on earlier patches from Heikki Krogerus in
Nokia N900 maemo kernel.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-By: Heikki Krogerus <heikki.krogerus@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Hwmod adaptation design requires each of the DSS HW IP to be a platform driver.
So a platform_driver for VENC is created and init exit methods are moved from core.c
to its driver probe,remove. pdev member has to be maintained by its own drivers.
Also, venc_vdda_dac reading is moved to venc.c.
VENC platform driver is registered from inside omap_dss_probe, in the order desired.
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Modifying the device & driver name from "mmci-omap-hs" to
"omap_hsmmc".
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add SI4713 FM transmitter supplies, platform data and setup to RX-51/N900.
It is connected to line output signals of TLV320AIC34 codec A part.
Driver can be either built-in or a module. It can be tuned with v4l2-ctl
from ivtv-utils. Following examples illustrate the use of it:
v4l2-ctl -d /dev/radio0 --set-ctrl=mute=0 (power up)
v4l2-ctl -d /dev/radio0 -f 107900 (tune 107.9 MHz)
v4l2-ctl -d /dev/radio0 --set-ctrl=mute=1 (power down)
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commmit 60d24ee "Added video data to support tvout on rx51" broke the DSS
on RX51/N900 since it added DSS VENC support but a patch adding needed
supply is missing from tree and no framebuffers are initialized.
This patch is basically cleaned up version of original one:
http://marc.info/?l=linux-omap&m=129070041402418&w=2
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Srikar <ext-srikar.1.bhavanarayana@nokia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It is much more cleaner to use REGULATOR_SUPPLY macro and a device name
instead of having a reference to rx51_display_device.dev with #if defined()
guards.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the TPA6130 is compiled as module the id and power_gpio values are
arbitrary at module probing time since the rx51_tpa6130a2_data was marked as
__initdata. Fix this by using __initdata_or_module. Then __initdata is
defined only if the kernel is built without CONFIG_MODULES and omitted
otherwise.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming ASoC core and tlv320aic3x changes makes possible to take b part of
TLV320AIC34 into use on RX51/N900. Prepare to this by adding virtual supplies
and platform data for b part of the codec.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove second tlv320aic3x.h inclusion that came along the commit f0fba2a
"ASoC: multi-component - ASoC Multi-Component Support".
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When OneNAND support is disabled, the platform code defines NULL
board_onenand_data and empty init function for us. By utilizing this we
can avoid cluttering board files with dummy definitions/wrappers.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Starting on OMAP4, the pin mux configuration is located in two
different partitions of the control module (CODE_PAD and WKUP_PAD).
The first one is inside the core power domain whereas the second
one is inside the wakeup.
- Add the capability to add any number of partition during board init
time depending of Soc partitioning.
- Add some init flags as well in order to avoid explicit Soc version
check inside the mux core code.
- Add a comment with mux0 mode on top of omap_mux/board/<partition>
if the current mux mode is not the default one.
Thanks to Tony Lindgren <tony@atomide.com> for the following improvements:
- Add omap_mux_get for getting the partition data so platform level
device code can use it.
- Fix the rx51 board code to use the new API.
- Do not store the partition for each mux entry. Look up the partition
for debugfs instead.
Thanks to Dan Murphy <dmurphy@ti.com> for testing on OMAP4 and reporting
a couple of bugs.
Thanks to Anand Gadiyar <gadiyar@ti.com> for testing on OMAP3 zoom and
bug report.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Murphy Dan <dmurphy@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
* git://git.infradead.org/battery-2.6:
power_supply: Makefile cleanup
bq27x00_battery: Add missing kfree(di->bus) in bq27x00_battery_remove()
power_supply: Introduce maximum current property
power_supply: Add types for USB chargers
ds2782_battery: Fix units
power_supply: Add driver for TWL4030/TPS65950 BCI charger
bq20z75: Add support for more power supply properties
wm831x_power: Add missing kfree(wm831x_power) in wm831x_power_remove()
jz4740-battery: Add missing kfree(jz_battery) in jz_battery_remove()
ds2760_battery: Add missing kfree(di) in ds2760_battery_remove()
olpc_battery: Fix endian neutral breakage for s16 values
ds2760_battery: Fix W1 and W1_SLAVE_DS2760 dependency
pcf50633-charger: Add missing sysfs_remove_group()
power_supply: Add driver for TI BQ20Z75 gas gauge IC
wm831x_power: Remove duplicate chg mask
omap: rx51: Add support for USB chargers
power_supply: Add isp1704 charger detection driver
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
The keypad matrix variable declaration is not matching
with structure variable keymap declared in keypad_matrix.h.
Due to this, following sparse warnings are generated with omap3_defconfig.
arch/arm/mach-omap2/board-devkit8000.c:223:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-devkit8000.c:223:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-devkit8000.c:223:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-ldp.c:107:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-ldp.c:107:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-ldp.c:107:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3evm.c:472:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3evm.c:472:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3evm.c:472:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-3430sdp.c:114:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-3430sdp.c:114:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-3430sdp.c:114:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-cm-t35.c:568:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-cm-t35.c:568:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-cm-t35.c:568:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3stalker.c:415:13: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3stalker.c:415:13: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3stalker.c:415:13: got int static [toplevel] *<noident>
This patch modifies the variable keymap declaration as per declaration in matrix_keymap structure.
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-input@vger.kernel.org
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/mach-omap2/timer-gp.c:115:12: warning: symbol 'omap2_gp_clockevent_set_gptimer' was not declared. Should it be static?
arch/arm/mach-omap2/powerdomain.c:993:5: warning: symbol 'pwrdm_set_lowpwrstchange' was not declared. Should it be static?
arch/arm/mach-omap2/board-flash.c:141:8: warning: symbol 'board_nand_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:416:6: warning: symbol 'n8x0_mmc_slot1_cover_handler' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:544:13: warning: symbol 'n8x0_mmc_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:902:13: warning: symbol 'rx51_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-video.c:107:13: warning: symbol 'rx51_video_mem_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-debugboard.c:155:12: warning: symbol 'zoom_debugboard_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:280:13: warning: symbol 'zoom_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-igep0020.c:110:13: warning: symbol 'igep2_flash_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:109:6: warning: symbol 'am3517_evm_ethernet_init' was not declared. Should it be static?
drivers/mtd/onenand/omap2.c:577:5: warning: symbol 'omap2_onenand_rephase' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move wl12xx.h outside of the spi-specific location,
so it can be shared with both spi and sdio solutions.
Update all users of spi/wl12xx.h accordingly
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Redefinition of rx51_aic3x_data got introduced when merging upstread changes
for 2.6.36 and ASoC Multi-Component Support.
This must go together with multi-component commit f0fba2a.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This enables isp1704 power supply driver on RX51, allowing
USB charger detection with N900.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Fairly simple conflicts, the most serious ones are the i.MX ones which I
suspect now need another rename.
Conflicts:
arch/arm/mach-mx2/clock_imx27.c
arch/arm/mach-mx2/devices.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-zoom2.c
sound/soc/fsl/mpc5200_dma.c
sound/soc/fsl/mpc5200_dma.h
sound/soc/fsl/mpc8610_hpcd.c
sound/soc/pxa/spitz.c
This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.
struct snd_soc_codec ---> struct snd_soc_codec (device data)
+-> struct snd_soc_codec_driver (driver data)
struct snd_soc_platform ---> struct snd_soc_platform (device data)
+-> struct snd_soc_platform_driver (driver data)
struct snd_soc_dai ---> struct snd_soc_dai (device data)
+-> struct snd_soc_dai_driver (driver data)
struct snd_soc_device ---> deleted
This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.
The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.
This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.
Other notable multi-component changes:-
* Stream operations now de-reference less structures.
* close_delayed work() now runs on a DAI basis rather than looping all DAIs
in a card.
* PM suspend()/resume() operations can now handle N CODECs and Platforms
per sound card.
* Added soc_bind_dai_link() to bind the component devices to the sound card.
* Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
DAI link components.
* sysfs entries can now be registered per component per card.
* snd_soc_new_pcms() functionailty rolled into dai_link_probe().
* snd_soc_register_codec() now does all the codec list and mutex init.
This patch changes the probe() and remove() of the CODEC drivers as follows:-
o Make CODEC driver a platform driver
o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
o Removed all static codec pointers (drivers now support > 1 codec dev)
o snd_soc_register_pcms() now done by core.
o snd_soc_register_dai() folded into snd_soc_register_codec().
CS4270 portions:
Acked-by: Timur Tabi <timur@freescale.com>
Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
TI CODEC and OMAP fixes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Samsung platform and misc fixes :-
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
MPC8610 and PPC fixes.
Signed-off-by: Timur Tabi <timur@freescale.com>
i.MX fixes and some core fixes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
J4740 platform fixes:-
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This commit will enable usage of tsl2563 ambient light sensor on Nokia N900.
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With these and upcoming change to tpa6130a2 driver it's possible to add
support for the TPA6130A2 headphone amplifier.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is REGULATOR_SUPPLY macro available for initializing the struct
regulator_consumer_supply so use it where applicable (all other supplies
than vdds_sdi) as it improves the readability.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Proper operation of the tlv320aic3x audio codec requires that reset
sequencing is done in pair with supply voltages when using the regulator
framework. Add the codec reset gpio used in Nokia RX51 to tlv320aic3x
data.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It seems that the battery cover sensor in Nokia N900 is powered from the
V28 domain. Now if this regulator is disabled it causes that the gpio 160
reads only zero which effectively causes uSD removal detection.
Currently the bootloader enabled V28 is kept on but this may change in the
future according to comment in
drivers/regulator/core.c: regulator_has_full_constraints.
Also if there are any consumers on the V28 domain doing regulator_enable
regulator_disable cycle the V28 will be disabled after that.
Prepare for these by defining the V28 as always_on regulator.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds