Switch to using both register sets - side A and side B for display panning.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the Migo-R board code to register devices at
arch_initcall() time instead of __initcall(). This fix
unbreaks migor_ts touch screen driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Migo-R board specific on-chip sh7722
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Unify i2c camera device platform data to point to struct soc_camera_link
for a smooth transition to soc-camera as a platform driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds mode pin configuration and
a machvec structure to Migo-R.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All soc-camera camera and host drivers must specify supported data signal
polarity, after all drivers are fixed, we'll add a suitable test to
soc_camera_bus_param_compatible().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If CONFIG_PM is set, let Migo-R LEDs show sleep states.
D11 will show STATUS0 and D12 PDSTATUS.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds CN9 MMC support for MigoR using the mmc_spi
driver on top of the bitbanging spi_gpio driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Migo-R can use ov772x camera driver in Linux 2.6.29.
Therefore, soc_camera_platform setting is no longer needed.
This patch removes it.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable LCDC deferred io on Migo-R using 1s delay.
As with other deferred io frame buffers user space code should
use fsync() on the frame buffer device to trigger an update.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add LCDC interrupt resources for AP325 and Migo-R. The LCDC driver does
not require interrupts at this point, but changes such as one-shot SYS
mode using deferred io, and wait-for-vblank will both need this.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This kills off the special Migo-R machvec, as nothing is using it. By
default this will switch to using the generic machvec, which provides the
same functionality. This saves us a bit of space in the machvec section.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the lcdc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile ceu and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile keysc driver and
adjust the board specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use a slower VIO_CKO clock frequency for the ov772x on Migo-R.
This improves the camera picture quality on Panel Board V2.1.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the ov772x byte sequence to enable byte swap. This to reflect
the recent CEU driver change to follow incoming byte order.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Improve Migo-R ethernet performance by reducing smc91x overruns.
This is done by enabling SMC91X_NOWAIT and optimizing CS4 setup.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on Migo-R and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
Fix whitespace damage while at it and add 2 LEDs and export them to
user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a workaround for users of sh_mobile_lcdcfb that don't
define HAVE_CLK and have otherwise sane clock initialization.
At the same time, move the sh_mobile_lcdc.h header to include/video/.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export the LCD panel size for sh_mobile_lcdc boards. This allows us
to perform dpi and screen aspect ratio calculations in user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix recently introduced I2C build breakage on AP325RXA and Migo-R.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This flattens out the board directories in to individual mach groups,
we will use this for getting rid of unneeded directories, simplifying
the build system, and becoming more coherent with the refactored
arch/sh/include topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Phil Edworthy