Fix BBR so that upon notification of a loss recovery undo BBR resets
the full pipe detection (STARTUP exit) state machine.
Under high reordering, reordering events can be interpreted as loss.
If the reordering and spurious loss estimates are high enough, this
could previously cause BBR to spuriously estimate that the pipe is
full.
Since spurious loss recovery means that our overall sending will have
slowed down spuriously, this commit gives a flow more time to probe
robustly for bandwidth and decide the pipe is really full.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit records the "full bw reached" decision in a new
full_bw_reached bit. This is a pure refactor that does not change the
current behavior, but enables subsequent fixes and improvements.
In particular, this enables simple and clean fixes because the full_bw
and full_bw_cnt can be unconditionally zeroed without worrying about
forgetting that we estimated we filled the pipe in Startup. And it
enables future improvements because multiple code paths can be used
for estimating that we filled the pipe in Startup; any new code paths
only need to set this bit when they think the pipe is full.
Note that this fix intentionally reduces the width of the full_bw_cnt
counter, since we have never used the most significant bit.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bytes_compl and pkts_compl pointers passed to efx_dequeue_buffers
cannot be NULL. Add a paranoid warning to check this condition and fix
the one case where they were NULL.
efx_enqueue_unwind() is called very rarely, during error handling.
Without this fix it would fail with a NULL pointer dereference in
efx_dequeue_buffer, with efx_enqueue_skb in the call stack.
Fixes: e9117e5099 ("sfc: Firmware-Assisted TSO version 2")
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This controller does not support EEE, but it may connect to a PHY
which supports EEE and advertises EEE by default, while its link
partner also advertises EEE. If this happens, the PHY enters low
power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
gianfar connects to, to prevent the above unwanted outcome.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Tested-by: Yangbo Lu <Yangbo.lu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 fixes from Martin Schwidefsky:
- three more patches in regard to the SPDX license tags. The missing
tags for the files in arch/s390/kvm will be merged via the KVM tree.
With that all s390 related files should have their SPDX tags.
- a patch to get rid of 'struct timespec' in the DASD driver.
- bug fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix compat system call table
s390/mm: fix off-by-one bug in 5-level page table handling
s390: Remove redudant license text
s390: add a few more SPDX identifiers
s390/dasd: prevent prefix I/O error
s390: always save and restore all registers on context switch
s390/dasd: remove 'struct timespec' usage
s390/qdio: restrict target-full handling to IQDIO
s390/qdio: consider ERROR buffers for inbound-full condition
s390/virtio: add BSD license to virtio-ccw
- Fix SW PAN pgd shadowing for kernel threads, EFI and exiting user tasks
- Fix FP register leak when a task_struct is re-allocated
- Fix potential use-after-free in FP state tracking used by KVM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJaKUT9AAoJELescNyEwWM0AdIH/RmM1E3LIbOga+9DyqeQ4i8/
+8AVV0wFEyIYZY3APrFEnasrjuunWvCUZMOT5HwkfcWpBUmxKHmgG/Jy0dgvZ9at
xC5WAgYZuN2Z1U9smrCWVBiUlojrxbaEPS/RR4QqB0ViHg2xBL8TW6Dolm8Rt4ei
UMXyhLAzUPgTIzN+xiW10dg5VqwLv2y1HvbbaF3bUhidrccMeyz+7bpwYfk26n+c
2N7XJqc9t7DxqBpr1ZSwUzAz89wVDI7cCll+9nTS0/UBDeYXSHwTqO8MbmoRVPo9
Mlf0NdFwTqKE0YS/4q2QBfMog4fzJQmQrcrsoHUy/ZA2IBuUxKsBVn4SCG0Y9Q8=
=Esv9
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Fix some more FP register fallout from the SVE patches and also some
problems with the PGD tracking in our software PAN emulation code,
after we received a crash report from a 3.18 kernel running a
backport.
Summary:
- fix SW PAN pgd shadowing for kernel threads, EFI and exiting user
tasks
- fix FP register leak when a task_struct is re-allocated
- fix potential use-after-free in FP state tracking used by KVM"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/sve: Avoid dereference of dead task_struct in KVM guest entry
arm64: SW PAN: Update saved ttbr0 value on enter_lazy_tlb
arm64: SW PAN: Point saved ttbr0 at the zero page when switching to init_mm
arm64: fpsimd: Abstract out binding of task's fpsimd context to the cpu.
arm64: fpsimd: Prevent registers leaking from dead tasks
This fixes an out of bounds warning from KASAN in the ACPI
CPPC driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJaKXLtAAoJEILEb/54YlRxEmUQAJ1MnvVoCIpB/NC/gcp8wBwZ
Y9rOJhnsgTiAA8Or7YJCOhPAHCa2S16m/nCkgrZfSjNgYJ/nHT8SB5vw8Fkc/PIz
Jmc3E/yVvn446c9ozSa3NALth5Ov90ys4HFsF3jjetTr7aDwmwjaC2pIGRBd6pUK
nk1MBMdu4wsGYssCV3dMjH4B1TmnU3rLyCl95yFFI8jgjA4slVk+I3EtxrlSOOHy
9wnbHOWch2UbJBDQLIhhgXKcUXDxnwfBJ8aoEGQ2LokTU1pdXMJG2RFPKG1Dtuqh
JBhSRXe7jA7jkdGda6sXFOWc7hXMscf0FMOvf3+x7q91OIumtNqxIm45nTEdMOBl
vT5eFsAUOD8HzaA9BYt/QVIFR9jG0leofVpgK+xGVzISWrLSavaEcuX1gblJ120I
iJMd0zuPnrktjYRn6VWxVKXpGKr4/EqCuVRE3EHG9aERJtKsfN9vIh66m97JfI2D
Eb8ifaL7nVIALoWPlq53Lhjllf/cCwvoUNMLhnnoqZU5HWOfolTyGQHeI0DjhQv2
UCxjuKFCtBKQyMNNyWXF1MWOGcgky3v/4HdkYjfly1h0eO6l5owilj+OW4cxss9l
NtUCuT2IsQ6dO5oooz+fHzvz0AkgtB+pYLZie28+b3Y5CgvnKTYsnxeMVchkcmo1
XnL6KGvGgX68z/0AVrMt
=35fs
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This fixes an out of bounds warning from KASAN in the ACPI CPPC
driver"
* tag 'acpi-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / CPPC: Fix KASAN global out of bounds warning
This fixes an issue in the device runtime PM framework that prevents
customer devices from resuming if runtime PM is disabled for one or
more of their supplier devices (as reflected by device links between
those devices).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/T0U
-----END PGP SIGNATURE-----
Merge tag 'pm-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"This fixes an issue in the device runtime PM framework that prevents
customer devices from resuming if runtime PM is disabled for one or
more of their supplier devices (as reflected by device links between
those devices)"
* tag 'pm-4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / runtime: Fix handling of suppliers with disabled runtime PM
Make it more clear that nodes without "__overlay__" subnodes are
skipped, by reverting the logic and using continue.
This also reduces indentation level.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
If an overlay has no "__symbols__" node, but it has nodes without
"__overlay__" subnodes at the end (e.g. a "__fixups__" node), after
filling in all fragments for nodes with "__overlay__" subnodes,
"fragment = &fragments[cnt]" will point beyond the end of the allocated
array.
Hence writing to "fragment->overlay" will overwrite unallocated memory,
which may lead to a crash later.
Fix this by deferring both the assignment to "fragment" and the
offending write afterwards until we know for sure the node has an
"__overlay__" subnode, and thus a valid entry in "fragments[]".
Fixes: 61b4de4e0b ("of: overlay: minor restructuring")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Mark tcp_sock during a SACK reneging event and invalidate rate samples
while marked. Such rate samples may overestimate bw by including packets
that were SACKed before reneging.
< ack 6001 win 10000 sack 7001:38001
< ack 7001 win 0 sack 8001:38001 // Reneg detected
> seq 7001:8001 // RTO, SACK cleared.
< ack 38001 win 10000
In above example the rate sample taken after the last ack will count
7001-38001 as delivered while the actual delivery rate likely could
be much lower i.e. 7001-8001.
This patch adds a new field tcp_sock.sack_reneg and marks it when we
declare SACK reneging and entering TCP_CA_Loss, and unmarks it after
the last rate sample was taken before moving back to TCP_CA_Open. This
patch also invalidates rate samples taken while tcp_sock.is_sack_reneg
is set.
Fixes: b9f64820fb ("tcp: track data delivery rate for a TCP connection")
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't rely on can_get_echo_skb() return value to wake the network tx
queue up: can_get_echo_skb() returns 0 if the echo array slot was not
occupied, but also when the DLC of the released echo frame was 0.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When we unplug the device, we can see both -EPIPE and -EPROTO depending
on exact timing and what system we run on. If we continue to resubmit
URBs, they will immediately fail, and they can cause stalls, especially
on slower CPUs.
Fix this by not resubmitting on -EPROTO, as we already do on -EPIPE.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The added check produces a build error when CONFIG_PROC_FS is
disabled:
net/ipv4/netfilter/ipt_CLUSTERIP.c: In function 'clusterip_net_exit':
net/ipv4/netfilter/ipt_CLUSTERIP.c:822:28: error: 'cn' undeclared (first use in this function)
This moves the variable declaration out of the #ifdef to make it
available to the WARN_ON_ONCE().
Fixes: 613d0776d3 ("netfilter: exit_net cleanup check added")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
regression fix for vc4 + rpm stable fix for analogix bridge
* tag 'drm-misc-fixes-2017-12-07' of git://anongit.freedesktop.org/drm/drm-misc:
drm/bridge: analogix dp: Fix runtime PM state in get_modes() callback
drm/vc4: Fix false positive WARN() backtrace on refcount_inc() usage
- Fix for fd.o bug #103997 CNL eDP + HDMI causing a machine hard hang (James)
- Fix to allow suspending with a wedged GPU to hopefully unwedge it (Chris)
- Fix for Gen2 vblank timestap/frame counter jumps (Ville)
- Revert of a W/A for enabling FBC on CNL/GLK for certain images
and sizes (Rodrigo)
- Lockdep fix for i915 userptr code (Chris)
gvt-fixes-2017-12-06
- Fix invalid hw reg read value for vGPU (Xiong)
- Fix qemu warning on PCI ROM bar missing (Changbin)
- Workaround preemption regression (Zhenyu)
* tag 'drm-intel-fixes-2017-12-07' of git://anongit.freedesktop.org/drm/drm-intel:
Revert "drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk"
drm/i915: Call i915_gem_init_userptr() before taking struct_mutex
drm/i915/gvt: set max priority for gvt context
drm/i915/gvt: Don't mark vgpu context as inactive when preempted
drm/i915/gvt: Limit read hw reg to active vgpu
drm/i915/gvt: Export intel_gvt_render_mmio_to_ring_id()
drm/i915/gvt: Emulate PCI expansion ROM base address register
drm/i915/cnl: Mask previous DDI - PLL mapping
drm/i915: Fix vblank timestamp/frame counter jumps on gen2
drm/i915: Skip switch-to-kernel-context on suspend when wedged
- fix page fault issue due to using wrong device object in prime import.
- drop NONCONTIG flag without IOMMU support.
- remove unnecessary members and declaration.
* tag 'exynos-drm-fixes-for-v4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: remove unnecessary function declaration
drm/exynos: remove unnecessary descrptions
drm/exynos: gem: Drop NONCONTIG flag for buffers allocated without IOMMU
drm/exynos: Fix dma-buf import
Daniel Borkmann says:
====================
pull-request: bpf 2017-12-06
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fixing broken uapi for BPF tracing programs for s390 and arm64
architectures due to pt_regs being in-kernel only, and not part
of uapi right now. A wrapper is added that exports pt_regs in
an asm-generic way. For arm64 this maps to existing user_pt_regs
structure and for s390 a user_pt_regs structure exporting the
beginning of pt_regs is added and uapi-exported, thus fixing the
BPF issues seen in perf (and BPF selftests), all from Hendrik.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The qmi_wwan minidriver support a 'raw-ip' mode where frames are
received without any ethernet header. This causes alignment issues
because the skbs allocated by usbnet are "IP aligned".
Fix by allowing minidrivers to disable the additional alignment
offset. This is implemented using a per-device flag, since the same
minidriver also supports 'ethernet' mode.
Fixes: 32f7adf633 ("net: qmi_wwan: support "raw IP" mode")
Reported-and-tested-by: Jay Foster <jay@systech.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I switched rcv_rtt_est to high resolution timestamps, I forgot
that tp->tcp_mstamp needed to be refreshed in tcp_rcv_space_adjust()
Using an old timestamp leads to autotuning lags.
Fixes: 645f4c6f2e ("tcp: switch rcv_rtt_est and rcvq_space to high resolution timestamps")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 28033ae4e0 ("net: netlink: Update attr validation to require
exact length for some types") requires attributes using types NLA_U* and
NLA_S* to have an exact length. This change is exposing bugs in various
userspace commands that are sending attributes with an invalid length
(e.g., attribute has type NLA_U8 and userspace sends NLA_U32). While
the commands are clearly broken and need to be fixed, users are arguing
that the sudden change in enforcement is breaking older commands on
newer kernels for use cases that otherwise "worked".
Relax the validation to print a warning mesage similar to what is done
for messages containing extra bytes after parsing.
Fixes: 28033ae4e0 ("net: netlink: Update attr validation to require exact length for some types")
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
introduced new exit point in ipxip6_rcv. however rcu_read_unlock is
missing there. this diff is fixing this
v1->v2:
instead of doing rcu_read_unlock in place, we are going to "drop"
section (to prevent skb leakage)
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Signed-off-by: Nikita V. Shirokov <tehnerd@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
mv88e6xxx error patch fixes
While trying to bring up a new PHY on a board, i exercised the error
paths a bit, and discovered some bugs. The unwind for interrupt
handling deadlocks, and the MDIO code hits a BUG() when a registered
MDIO device is freed without first being unregistered.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO busses need to be unregistered before they are freed,
otherwise BUG() is called. Add a call to the unregister code if the
registration fails, since we can have multiple busses, of which some
may correctly register before one fails. This requires moving the code
around a little.
Fixes: a3c53be55c ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing the interrupt handling code, we should mask the
generation of interrupts. The code however unmasked all
interrupts. This can then cause a new interrupt. We then get into a
deadlock where the interrupt thread is waiting to run, and the code
continues, trying to remove the interrupt handler, which means waiting
for the thread to complete. On a UP machine this deadlocks.
Fix so we really mask interrupts in the hardware. The same error is
made in the error path when install the interrupt handling code.
Fixes: 3460a5770c ("net: dsa: mv88e6xxx: Mask g1 interrupts and free interrupt")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
add appropriate calls to clk_disable_unprepare() by jumping to out_mdio
in case orion_mdio_probe() returns -EPROBE_DEFER.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3d604da1e9 ("net: mvmdio: get and enable optional clock")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function virtqueue_get_buf_ctx() could return NULL, the return
value 'buf' need to be checked with NULL, not value 'ctx'.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cleanup all resource allocated by virtio_mmio_probe.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
As mentioned at drivers/base/core.c:
/*
* NOTE: _Never_ directly free @dev after calling this function, even
* if it returned an error! Always use put_device() to give up the
* reference initialized in this function instead.
*/
so we don't free vm_dev until vm_dev.dev.release be called.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
get_modes() callback might be called asynchronously from the DRM core and
it is not synchronized with bridge_enable(), which sets proper runtime PM
state of the main DP device. Fix this by calling pm_runtime_get_sync()
before calling drm_get_edid(), which in turn calls drm_dp_i2c_xfer() and
analogix_dp_transfer() to ensure that main DP device is runtime active
when doing any access to its registers.
This fixes the following kernel issue on Samsung Exynos5250 Snow board:
Unhandled fault: imprecise external abort (0x406) at 0x00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: : 406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 62 Comm: kworker/0:2 Not tainted 4.13.0-rc2-00364-g4a97a3da420b #3357
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events output_poll_execute
task: edc14800 task.stack: edcb2000
PC is at analogix_dp_transfer+0x15c/0x2fc
LR is at analogix_dp_transfer+0x134/0x2fc
pc : [<c0468538>] lr : [<c0468510>] psr: 60000013
sp : edcb3be8 ip : 0000002a fp : 00000001
r10: 00000000 r9 : edcb3cd8 r8 : edcb3c40
r7 : 00000000 r6 : edd3b380 r5 : edd3b010 r4 : 00000064
r3 : 00000000 r2 : f0ad3000 r1 : edcb3c40 r0 : edd3b010
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 4000406a DAC: 00000051
Process kworker/0:2 (pid: 62, stack limit = 0xedcb2210)
Stack: (0xedcb3be8 to 0xedcb4000)
[<c0468538>] (analogix_dp_transfer) from [<c0424ba4>] (drm_dp_i2c_do_msg+0x8c/0x2b4)
[<c0424ba4>] (drm_dp_i2c_do_msg) from [<c0424e64>] (drm_dp_i2c_xfer+0x98/0x214)
[<c0424e64>] (drm_dp_i2c_xfer) from [<c057b2d8>] (__i2c_transfer+0x140/0x29c)
[<c057b2d8>] (__i2c_transfer) from [<c057b4a4>] (i2c_transfer+0x70/0xe4)
[<c057b4a4>] (i2c_transfer) from [<c0441de4>] (drm_do_probe_ddc_edid+0xb4/0x114)
[<c0441de4>] (drm_do_probe_ddc_edid) from [<c0441e5c>] (drm_probe_ddc+0x18/0x28)
[<c0441e5c>] (drm_probe_ddc) from [<c0445728>] (drm_get_edid+0x124/0x2d4)
[<c0445728>] (drm_get_edid) from [<c0465ea0>] (analogix_dp_get_modes+0x90/0x114)
[<c0465ea0>] (analogix_dp_get_modes) from [<c0425e8c>] (drm_helper_probe_single_connector_modes+0x198/0x68c)
[<c0425e8c>] (drm_helper_probe_single_connector_modes) from [<c04325d4>] (drm_setup_crtcs+0x1b4/0xd18)
[<c04325d4>] (drm_setup_crtcs) from [<c04344a8>] (drm_fb_helper_hotplug_event+0x94/0xd0)
[<c04344a8>] (drm_fb_helper_hotplug_event) from [<c0425a50>] (drm_kms_helper_hotplug_event+0x24/0x28)
[<c0425a50>] (drm_kms_helper_hotplug_event) from [<c04263ec>] (output_poll_execute+0x6c/0x174)
[<c04263ec>] (output_poll_execute) from [<c0136f18>] (process_one_work+0x188/0x3fc)
[<c0136f18>] (process_one_work) from [<c01371f4>] (worker_thread+0x30/0x4b8)
[<c01371f4>] (worker_thread) from [<c013daf8>] (kthread+0x128/0x164)
[<c013daf8>] (kthread) from [<c0108510>] (ret_from_fork+0x14/0x24)
Code: 0a000002 ea000009 e2544001 0a00004a (e59537c8)
---[ end trace cddc7919c79f7878 ]---
Reported-by: Misha Komarovskiy <zombah@gmail.com>
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171121074936.22520-1-m.szyprowski@samsung.com
* Tell mac80211 when the MAC has been stripped (9000 series);
* Tell mac80211 when the IVC has been stripped (9000 series);
* Add 2 new PCI IDs, one for 9000 and one for 22000;
* Fix a queue hang due during ROC.
-----BEGIN PGP SIGNATURE-----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=VSq5
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Third batch of iwlwifi patches intended for 4.15.
* Tell mac80211 when the MAC has been stripped (9000 series);
* Tell mac80211 when the IVC has been stripped (9000 series);
* Add 2 new PCI IDs, one for 9000 and one for 22000;
* Fix a queue hang due during ROC.
When I run make W=1 on gcc (Debian 7.2.0-16) 7.2.0 I got an error for
the first run, all next ones are okay.
CC [M] drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:2078: error: Cannot parse struct or union!
scripts/Makefile.build:310: recipe for target 'drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o' failed
Seems like something happened with W=1 and wrong kernel doc format.
As a quick fix remove dubious /** in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 8f067837c4.
HSD says "WA withdrawn. It was causing corruption with some images.
WA is not strictly necessary since this bug just causes loss of FBC
compression with some sizes and images, but doesn't break anything."
Fixes: 8f067837c4 ("drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171117010825.23118-1-radhakrishna.sripada@intel.com
(cherry picked from commit 0cfecb7c4b)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
With CONFIG_REFCOUNT_FULL enabled, refcount_inc() complains when it's
passed a refcount object that has its counter set to 0. In this driver,
this is a valid use case since we want to increment ->usecnt only when
the BO object starts to be used by real HW components and this is
definitely not the case when the BO is created.
Fix the problem by using refcount_inc_not_zero() instead of
refcount_inc() and fallback to refcount_set(1) when
refcount_inc_not_zero() returns false. Note that this 2-steps operation
is not racy here because the whole section is protected by a mutex
which guarantees that the counter does not change between the
refcount_inc_not_zero() and refcount_set() calls.
Fixes: b9f19259b8 ("drm/vc4: Add the DRM_IOCTL_VC4_GEM_MADVISE ioctl")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20171122203928.28135-1-boris.brezillon@free-electrons.com
When wiring up the socket system calls the compat entries were
incorrectly set. Not all of them point to the corresponding compat
wrapper functions, which clear the upper 33 bits of user space
pointers, like it is required.
Fixes: 977108f89c ("s390: wire up separate socketcalls system calls")
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* Fix long standing problem with kdb kallsyms_symbol_next() return value
* Add new co-maintainer Daniel Thompson
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJaKG1/AAoJEIciOldedpOjtigP/Rp1CK9EGtzZCW7a1wZp7d/n
OsAUKrj1AEvve+PpZXBw9X3XMYpXbGyzDfU59NLzMZmgZ6idIdwBwlO6AgWSRyXY
EjvYOvkIytk2ONFVQeDPfbAi5pPaSgTmt813pApka4mbUlWYgC4TioNove4Q08R+
CZrXiD2WeKlBxB2TgfYu+0Sy3TtYv7aaJhV45ziPjiwyFpcl9Ktp5zEVOcK6Xw10
8T5ZLA7k/MKah+CoqBdzRZ0IprBVAB4MMTBV3q7HXNXOMX6JdXgg1UihqKJcYF5u
6d+PS6A8sFGicUguPXMZh90vM2f0hg+ZagavskSLCp8usL91+4UmAxHaRdKUTqWC
k1jmxODsJPiBFi05mSem94WtegjBkrUMohGcKyfjEdixjZfa9G6Zhux/951HFkrl
UdUSlTnfO39Cj3V5AkSR95wBVuPgjMKSBVDxKuUrWib2p3Wx0P/eeDtcgy+yPHkX
Gxxa5nhmBUJJZCWl08kKQ1oacVX5/sg9ZcmpAXzcR3lLYL/GlgiB9tS8piRGLUN6
GVneU5uqVnj1Jm67J7SVZtPsvbhV2jEP9aeNx8MZzaTJ412XzYeMB9P88JFQpZRj
UXxhF/Q5HsjxKX0XKUD9O3W4KXD1YYWHng3ljarzR25Sd3zA7Y5HJ3NnCZRRa3Mm
hVgJQIk1xB40aNnRVXJT
=2jeq
-----END PGP SIGNATURE-----
Merge tag 'for_linus-4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull kgdb fixes from Jason Wessel:
- Fix long standing problem with kdb kallsyms_symbol_next() return
value
- Add new co-maintainer Daniel Thompson
* tag 'for_linus-4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kgdb/kdb/debug_core: Add co-maintainer Daniel Thompson
kdb: Fix handling of kallsyms_symbol_next() return value
It's a user pointer, and while the permissions of the file are pretty
questionable (should it really be readable to everybody), hashing the
pointer isn't going to be the solution.
We should take a closer look at more of the /proc/<pid> file permissions
in general. Sure, we do want many of them to often be readable (for
'ps' and friends), but I think we should probably do a few conversions
from S_IRUGO to S_IRUSR.
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull m68knommu fixes from Greg Ungerer:
"There are two fixes here. One to add a missing linker section to the
m68k architecture linker scripts, the other to fix a defconfig build
problem"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k/defconfig: fix stmark2 broken local compilation
m68k: add missing SOFTIRQENTRY_TEXT linker section
Pull misc x86 fixes from Ingo Molnar:
- make CR4 handling irq-safe, which bug vmware guests ran into
- don't crash on early IRQs in Xen guests
- don't crash secondary CPU bringup if #UD assisted WARN()ings are
triggered
- make X86_BUG_FXSAVE_LEAK optional on newer AMD CPUs that have the fix
- fix AMD Fam17h microcode loading
- fix broadcom_postcore_init() if ACPI is disabled
- fix resume regression in __restore_processor_context()
- fix Sparse warnings
- fix a GCC-8 warning
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Change time() prototype to match __vdso_time()
x86: Fix Sparse warnings about non-static functions
x86/power: Fix some ordering bugs in __restore_processor_context()
x86/PCI: Make broadcom_postcore_init() check acpi_disabled
x86/microcode/AMD: Add support for fam17h microcode loading
x86/cpufeatures: Make X86_BUG_FXSAVE_LEAK detectable in CPUID on AMD
x86/idt: Load idt early in start_secondary
x86/xen: Support early interrupts in xen pv guests
x86/tlb: Disable interrupts when changing CR4
x86/tlb: Refactor CR4 setting and shadow write
Pull CPU hotplug fix from Ingo Molnar:
"A single fix moving the smp-call queue flush step to the intended
point in the state machine"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp/hotplug: Move step CPUHP_AP_SMPCFD_DYING to the correct place
Pull scheduler fixes from Ingo Molnar:
"This includes a fix for the add_wait_queue() queue ordering brown
paperbag bug, plus PELT accounting fixes for cgroups scheduling
artifacts"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Update and fix the runnable propagation rule
sched/wait: Fix add_wait_queue() behavioral change
Pull perf fixes from Ingo Molnar:
"This includes perf namespace support kernel side fixes, plus an
accumulated set of perf tooling fixes - including UAPI header
synchronization that should make the perf build less noisy"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
tooling/headers: Synchronize updated s390 and x86 UAPI headers
tools headers: Syncronize mman.h ABI header
tools headers: Synchronize prctl.h ABI header
tools headers: Synchronize KVM arch ABI headers
tools headers: Synchronize drm/i915_drm.h
tools headers uapi: Synchronize drm/drm.h
tools headers: Synchronize perf_event.h header
tools headers: Synchronize kernel ABI headers wrt SPDX tags
tools/headers: Synchronize kernel x86 UAPI headers
perf intel-pt: Bring instruction decoder files into line with the kernel
perf test: Fix test 21 for s390x
perf bench numa: Fixup discontiguous/sparse numa nodes
perf top: Use signal interface for SIGWINCH handler
perf top: Fix window dimensions change handling
perf: Fix header.size for namespace events
perf top: Ignore kptr_restrict when not sampling the kernel
perf record: Ignore kptr_restrict when not sampling the kernel
perf report: Ignore kptr_restrict when not sampling the kernel
perf evlist: Add helper to check if attr.exclude_kernel is set in all evsels
perf test shell: Fix test case probe libc's inet_pton on s390x
...
Pull lockdep fix from Ingo Molnar:
"Fix a possible NULL dereference for the (rare) case when a task
doesn't have ->xhlocks space allocated due to kmalloc() OOM-ing"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Fix possible NULL deref
