[ Upstream commit bf990c1023 ]
For Hamedal C20, the current rate is different from the runtime rate,
snd_usb_endpoint stop and close endpoint to resetting rate.
if snd_usb_endpoint close the endpoint, sometimes usb will
disconnect the device.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Link: https://lore.kernel.org/r/20221110063452.295110-1-aichao@kylinos.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ad72c3c3f6 upstream.
snd_usbmidi_output_open() has a check of the NULL port with
snd_BUG_ON(). snd_BUG_ON() was used as this shouldn't have happened,
but in reality, the NULL port may be seen when the device gives an
invalid endpoint setup at the descriptor, hence the driver skips the
allocation. That is, the check itself is valid and snd_BUG_ON()
should be dropped from there. Otherwise it's confusing as if it were
a real bug, as recently syzbot stumbled on it.
Reported-by: syzbot+9abda841d636d86c41da@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/syzbot+9abda841d636d86c41da@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20221112141223.6144-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8cbd4725ff upstream.
Accuphase DAC-60 option card supports native DSD up to DSD256,
but doesn't have support for auto-detection. Explicitly enable
DSD support for the correct altsetting.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221108221241.1220878-1-jussi@sonarnerd.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 971cb608d1 upstream.
Although we tried to fix the regression for the recent changes with
the delayed card registration, it doesn't seem covering the all
cases; e.g. on Roland EDIROL M-100FX, where the generic quirk for
Roland devices is applied, it misses the card registration because the
detection of the last interface (apparently for MIDI) fails.
This patch is an attempt to recover from those failures by calling the
card register also at the error path for the secondary interfaces.
The card register condition is also extended to match with the old
check in the previous patch, too (i.e. the simple check of the
interface number) for catching the probe with errors.
Fixes: 39efc9c8a9 ("ALSA: usb-audio: Fix last interface check for registration")
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.suse.com/show_bug.cgi?id=1205111
Link: https://lore.kernel.org/r/20221108065824.14418-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b4f0debb3 upstream.
With the recent addition of hashed controls lookup it's not enough to just
update the control name field, the hash entries for the modified control
have to be updated too.
snd_ctl_rename() takes care of that, so use it instead of directly
modifying the control name.
Fixes: c27e1efb61 ("ALSA: control: Use xarray for faster lookups")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Link: https://lore.kernel.org/r/723877882e3a56bb42a2a2214cfc85f347d36e19.1666296963.git.maciej.szmigiero@oracle.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39efc9c8a9 upstream.
The recent fix in commit 6392dcd1d0 ("ALSA: usb-audio: Register card
at the last interface") tried to delay the card registration until the
last found interface is probed. It assumed that the probe callback
gets called for those later interfaces, but it's not always true; as
the driver loops over the descriptor and probes the matching ones,
it's not separately called via multiple probe calls. This results in
the missing card registration, i.e. no sound device.
For addressing this problem, replace the check whether the last
interface is processed with usb_interface_claimed() instead of the
comparison with the probe interface number.
Fixes: 6392dcd1d0 ("ALSA: usb-audio: Register card at the last interface")
Link: https://lore.kernel.org/r/20220915085947.7922-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6392dcd1d0 ]
The USB-audio driver matches per interface, and as default, it
registers the card instance at the very first instance. This can be a
problem for the devices that have multiple interfaces to be probed, as
the udev rule isn't applied properly for the later appearing
interfaces. Although we introduced the delayed_register option and
the quirks for covering those shortcomings, it's nothing but a
workaround for specific devices.
This patch is an another attempt to fix the problem in a more generic
way. Now the driver checks the whole USB device descriptor at the
very first time when an interface is attached to a sound card. It
looks at each matching interface in the descriptor and remembers the
last matching one. The snd_card_register() is invoked only when this
last interface is probed.
After this change, the quirks for the delayed registration become
superfluous, hence they are removed along with the patch. OTOH, the
delayed_register option is still kept, as it might be useful for some
corner cases (e.g. a special driver overtakes the interface probe from
the standard driver, and the last interface probe may miss).
Link: https://lore.kernel.org/r/20220904161247.16461-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a737e7f8b ]
We fixed the bug introduced by the patch for managing the shared
clocks at the commit 809f44a0cc ("ALSA: usb-audio: Clear fixed clock
rate at closing EP"), but it was merely a workaround. By this change,
the clock reference rate is cleared at each EP close, hence the still
remaining EP may need a re-setup of rate unnecessarily.
This patch introduces the proper refcounting for the clock reference
object so that the clock setup is done only when needed.
Fixes: 809f44a0cc ("ALSA: usb-audio: Clear fixed clock rate at closing EP")
Fixes: c11117b634 ("ALSA: usb-audio: Refcount multiple accesses on the single clock")
Link: https://lore.kernel.org/r/20220920181126.4912-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 568be8aaf8 upstream.
At an error path to release URB buffers and contexts, the driver might
hit a NULL dererence for u->urb pointer, when u->buffer_size has been
already set but the actual URB allocation failed.
Fix it by adding the NULL check of urb. Also, make sure that
buffer_size is cleared after the error path or the close.
Cc: <stable@vger.kernel.org>
Reported-by: Sabri N. Ferreiro <snferreiro1@gmail.com>
Link: https://lore.kernel.org/r/CAKG+3NRjTey+fFfUEGwuxL-pi_=T4cUskYG9OzpzHytF+tzYng@mail.gmail.com
Link: https://lore.kernel.org/r/20220930100129.19445-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6382da0828 upstream.
When the driver hits -ENOMEM at allocating a URB or a buffer, it
aborts and goes to the error path that releases the all previously
allocated resources. However, when -ENOMEM hits at the middle of the
sync EP URB allocation loop, the partially allocated URBs might be
left without released, because ep->nurbs is still zero at that point.
Fix it by setting ep->nurbs at first, so that the error handler loops
over the full URB list.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220930100151.19461-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ff878b408a.
Unfortunately the recent fix seems bringing another regressions with
PulseAudio / pipewire, at least for Steinberg and MOTU devices.
As a temporary solution, do a straight revert. The issue for Android
will be revisited again later by another different fix (if any).
Fixes: ff878b408a ("ALSA: usb-audio: Split endpoint setups for hw_params and prepare")
Cc: <stable@vger.kernel.org>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216500
Link: https://lore.kernel.org/r/20220920113929.25162-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent commit c11117b634 ("ALSA: usb-audio: Refcount multiple
accesses on the single clock") tries to manage the clock rate shared
by several endpoints. This was intended for avoiding the unmatched
rate by a different endpoint, but unfortunately, it introduced a
regression for PulseAudio and pipewire, too; those applications try to
probe the multiple possible rates (44.1k and 48kHz) and setting up the
normal rate fails but only the last rate is applied.
The cause is that the last sample rate is still left to the clock
reference even after closing the endpoint, and this value is still
used at the next open. It happens only when applications set up via
PCM prepare but don't start/stop the stream; the rate is reset when
the stream is stopped, but it's not cleared at close.
This patch addresses the issue above, simply by clearing the rate set
in the clock reference at the last close of each endpoint.
Fixes: c11117b634 ("ALSA: usb-audio: Refcount multiple accesses on the single clock")
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/all/YxXIWv8dYmg1tnXP@zx2c4.com/
Link: https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/2620
Link: https://lore.kernel.org/r/20220907100421.6443-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There may be a bad USB audio device with a USB ID of (0x04fa, 0x4201) and
the number of it's interfaces less than 4, an out-of-bounds read bug occurs
when parsing the interface descriptor for this device.
Fix this by checking the number of interfaces.
Signed-off-by: Dongxiang Ke <kdx.glider@gmail.com>
Link: https://lore.kernel.org/r/20220906024928.10951-1-kdx.glider@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One of the former changes for the endpoint management was the more
consistent setup of endpoints at hw_params.
snd_usb_endpoint_configure() is a single function that does the full
setup, and it's called from both PCM hw_params and prepare callbacks.
Although the EP setup at the prepare phase is usually skipped (by
checking need_setup flag), it may be still effective in some cases
like suspend/resume that requires the interface setup again.
As it's a full and single setup, the invocation of
snd_usb_endpoint_configure() includes not only the USB interface setup
but also the buffer release and allocation. OTOH, doing the buffer
release and re-allocation at PCM prepare phase is rather superfluous,
and better to be done only in the hw_params phase.
For those optimizations, this patch splits the endpoint setup to two
phases: snd_usb_endpoint_set_params() and snd_usb_endpoint_prepare(),
to be called from hw_params and from prepare, respectively.
Note that this patch changes the driver operation slightly,
effectively moving the USB interface setup again to PCM prepare stage
instead of hw_params stage, while the buffer allocation and such
initializations are still done at hw_params stage.
And, the change of the USB interface setup timing (moving to prepare)
gave an interesting "fix", too: it was reported that the recent
kernels caused silent output at the beginning on playbacks on some
devices on Android, and this change casually fixed the regression.
It seems that those devices are picky about the sample rate change (or
the interface change?), and don't follow the too immediate rate
changes.
Meanwhile, Android operates the PCM in the following order:
- open, then hw_params with the possibly highest sample rate
- close without prepare
- re-open, hw_params with the normal sample rate
- prepare, and start streaming
This procedure ended up the hw_params twice with different rates, and
because the recent kernel did set up the sample rate twice one and
after, it screwed up the device. OTOH, the earlier kernels didn't set
up the USB interface at hw_params, hence this problem didn't appear.
Now, with this patch, the USB interface setup is again back to the
prepare phase, and it works around the problem automagically.
Although we should address the sample rate problem in a more solid
way in future, let's keep things working as before for now.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Cc: <stable@vger.kernel.org>
Reported-by: chihhao chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/87e6d6ae69d68dc588ac9acc8c0f24d6188375c3.camel@mediatek.com
Link: https://lore.kernel.org/r/20220901124136.4984-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the delayed registration is specified via either delayed_register
option or the quirk, we delay the invocation of snd_card_register()
until the given interface. But if a wrong value has been set there
and there are more interfaces over the given interface number,
snd_card_register() call would be missing for those interfaces.
This patch catches up those missing calls by fixing the comparison of
the interface number. Now the call is skipped only if the processed
interface is less than the given interface, instead of the exact
match.
Fixes: b70038ef4f ("ALSA: usb-audio: Add delayed_register option")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216082
Link: https://lore.kernel.org/r/20220831125901.4660-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The info message that was added in the commit a4aad5636c ("ALSA:
usb-audio: Inform devices that need delayed registration") is actually
useful to know the need for the delayed registration. However, it
turned out that this doesn't catch the all cases; namely, this warned
only when a PCM stream is attached onto the existing PCM instance, but
it doesn't count for a newly created PCM instance. This made
confusion as if there were no further delayed registration.
This patch moves the check to the code path for either adding a stream
or creating a PCM instance. Also, make it simpler by checking the
card->registered flag instead of querying each snd_device state.
Fixes: a4aad5636c ("ALSA: usb-audio: Inform devices that need delayed registration")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216082
Link: https://lore.kernel.org/r/20220831125901.4660-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't populate the read-only array marker on the stack but instead make
it static const. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220809181544.3046429-1-colin.i.king@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS ROG Zenith II has two USB interfaces, one for the front headphone
and another for the rest I/O. Currently we provided the mixer mapping
for the latter but with an incomplete form.
This patch corrects and provides more comprehensive mixer mapping, as
well as providing the proper device names for both the front headphone
and main audio.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=211005
Fixes: 2a48218f8e ("ALSA: usb-audio: Add mixer workaround for TRX40 and co")
Link: https://lore.kernel.org/r/20220809073259.18849-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Focusrite Clarett+ 8Pre uses the same protocol as the Scarlett Gen
2 and Gen 3 product range. This patch adds support for the Clarett+
8Pre by adding appropriate entries to the scarlett2 driver.
The Clarett+ 2Pre and 4Pre, and the Clarett USB product line
presumably use the same protocol as well, so support for them can
easily be added if someone can test.
Signed-off-by: Christian Colglazier <christian@cacolglazier.com>
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/20220809043241.GA2749152@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For sysfs outputs, it's safer to use a new helper, sysfs_emit(),
instead of the raw sprintf() & co. This patch replaces those usages
straightforwardly with a new helper, sysfs_emit().
Link: https://lore.kernel.org/r/20220801165639.26030-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the driver fails in snd_card_register() at probe time, it will free
the 'bcd2k->midi_out_urb' before killing it, which may cause a UAF bug.
The following log can reveal it:
[ 50.727020] BUG: KASAN: use-after-free in bcd2000_input_complete+0x1f1/0x2e0 [snd_bcd2000]
[ 50.727623] Read of size 8 at addr ffff88810fab0e88 by task swapper/4/0
[ 50.729530] Call Trace:
[ 50.732899] bcd2000_input_complete+0x1f1/0x2e0 [snd_bcd2000]
Fix this by adding usb_kill_urb() before usb_free_urb().
Fixes: b47a22290d ("ALSA: MIDI driver for Behringer BCD2000 USB device")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220715010515.2087925-1-zheyuma97@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use atomic_try_cmpxchg instead of atomic_cmpxchg (*ptr, old, new) == old in
ep_state_update. x86 CMPXCHG instruction returns success in ZF flag,
so this change saves a compare after cmpxchg (and related move instruction
in front of cmpxchg).
No functional change intended.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Link: https://lore.kernel.org/r/20220713151946.4743-1-ubizjak@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This removes the need to power cycle the Dell WD15 dock if it has been
attached to a Windows machine.
The Windows driver puts the ALC4020 USB audio controller into
'manual mode', and then does all the power management and other
configuration itself, by sending HD audio commands directly to the
ALC3263 audio codec via vendor-type USB messages. If manual mode is off,
this is all handled by the firmware, and works well enough.
If manual mode is turned on, the latency of the SET INTERFACE command
goes from several hundred ms to less than 1 ms
(see https://bugzilla.suse.com/show_bug.cgi?id=1089467), but I'm not
sure if the additional code that would be required is worth it.
Funnily enough, the Windows driver tries to turn off manual mode when
the dock is disconnected, which doesn't work for obvious reasons.
Additionally, fix a bug in dell_dock_init_vol, which didn't work because
the Control Selector was missing.
Now, it properly resets the volume to 0dB.
Fixes: 964af639ad ("ALSA: usb-audio: Initialize Dell Dock playback volumes")
Signed-off-by: Jan Schär <jan@jschaer.ch>
Link: https://lore.kernel.org/r/20220627171855.42338-2-jan@jschaer.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Dell WD15 dock has a headset and a line out port. Add support for
detecting if a jack is inserted into one of these ports.
For the headset jack, additionally determine if a mic is present.
The WD15 contains an ALC4020 USB audio controller and ALC3263 audio codec
from Realtek. It is a UAC 1 device, and UAC 1 does not support jack
detection. Instead, jack detection works by sending HD Audio commands over
vendor-type USB messages.
I found out how it works by looking at USB captures on Windows.
The audio codec is very similar to the one supported by
sound/soc/codecs/rt298.c / rt298.h, some constant names and the mic
detection are adapted from there. The realtek_add_jack function is adapted
from build_connector_control in sound/usb/mixer.c.
I tested this on a WD15 dock with the latest firmware.
Signed-off-by: Jan Schär <jan@jschaer.ch>
Link: https://lore.kernel.org/r/20220627171855.42338-1-jan@jschaer.ch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of fixes for v5.19, quite large but nothing major - a good
chunk of it is more stuff that was identified by mixer-test regarding
event generation.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmK12zAACgkQJNaLcl1U
h9C1MQf/Z2R0KmA73QWqSut9IXwUGpAvPQJtx8hOUKkA7efQNcK4xywa0CbnmFLp
kUAAXD5FhpPkZpLDAmjpTVgmgB6Wep2FX5LM5YnUgC4/sha3OpnBPD3ryGVuhJ2b
X/70GfflZRmlLCzp4UALieqgRjXb/Lk6gqeCNOzr6A5ewYLq4/1h4rPRaWluZ4MQ
kjL4TXYfRXbK1g39EQMelV/HEgRiZ5NhnoujtOfQGZa8iUF9r9EAmD3PKqR0kp8d
vUD4nxt7PuQW+ksdnJuRsBII3/MwrkF8S5lgfyBW80C71YeGVaba0Ty05oTF2u2H
GAWHfoGTw1dDnI3JwcI+7ZT6zX+HpA==
=3OmW
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.19-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.19
A collection of fixes for v5.19, quite large but nothing major - a good
chunk of it is more stuff that was identified by mixer-test regarding
event generation.
The patch applies the same quirks used for SC-01 at firmware v1.1.0 to
the ones running v1.0.0, with respect to hard-coded sample rates.
I got two more units and successfully tested the patch series with both
firmwares.
The support is now complete (not accounting ASIO).
Signed-off-by: Egor Vorontsov <sdoregor@sdore.me>
Link: https://lore.kernel.org/r/20220627100041.2861494-2-sdoregor@sdore.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fiero SC-01 is a USB sound card with two mono inputs and a single
stereo output. The inputs are composed into a single stereo stream.
The device uses a vendor-provided driver on Windows and does not work
at all without it. The driver mostly provides ASIO functionality, but
also alters the way the sound card is queried for sample rates and
clocks.
ALSA queries those failing with an EPIPE (same as Windows 10 does).
Presumably, the vendor-provided driver does not query it at all, simply
matching by VID:PID. Thus, I consider this a buggy firmware and adhere
to a set of fixed endpoint quirks instead.
The soundcard has an internal clock. Implicit feedback mode is required
for the playback.
I have updated my device to v1.1.0 from a Windows 10 VM using a vendor-
provided binary prior to the development, hoping for it to just begin
working. The device provides no obvious way to downgrade the firmware,
and regardless, there's no binary available for v1.0.0 anyway.
Thus, I will be getting another unit to extend the patch with support
for that. Expected to be a simple copy-paste of the existing one,
though.
There were no previous reports of that device in context of Linux
anywhere. Other issues have been reported though, but that's out of the
scope.
Signed-off-by: Egor Vorontsov <sdoregor@sdore.me>
Link: https://lore.kernel.org/r/20220627100041.2861494-1-sdoregor@sdore.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Treat the claimed 96kHz 1ch in the descriptors as 48kHz 2ch, so that
the audio stream doesn't sound mono. Also fix initial stream
alignment, so that left and right channels are in the correct order.
Signed-off-by: John Veness <john-linux@pelago.org.uk>
Link: https://lore.kernel.org/r/20220624140757.28758-1-john-linux@pelago.org.uk
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both Behringer UMC 202 HD and 404 HD need explicit quirks to enable
the implicit feedback mode and start the playback stream primarily.
The former seems fixing the stuttering and the latter is required for
a playback-only case.
Note that the "clock source 41 is not valid" error message still
appears even after this fix, but it should be only once at probe.
The reason of the error is still unknown, but this seems to be mostly
harmless as it's a one-off error and the driver retires the clock
setup and it succeeds afterwards.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215934
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220624101132.14528-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Buffer overflow could occur in the loop "while", due to accessing an
array element before checking the index.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Daniil Dementev <d.dementev@ispras.ru>
Reviewed-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Link: https://lore.kernel.org/r/20220610165732.2904-1-d.dementev@ispras.ru
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Focusrite Saffire 6 has fixed audioformat quirks with multiple
endpoints assigned to a single altsetting. Unfortunately the generic
parser couldn't detect the sync endpoint correctly as the implicit
sync due to the missing EP attribute bits. In the former kernels, it
used to work somehow casually, but it's been broken for a while after
the large code change in 5.11.
This patch cures the regression by the following:
- Allow the static quirk table to provide the sync EP information;
we just need to fill the fields and let the generic parser skipping
parsing if sync_ep is already set.
- Add the sync endpoint information to the entry for Saffire 6.
Fixes: 7b0efea4ba ("ALSA: usb-audio: Add missing ep_idx in fixed EP quirks")
Reported-and-tested-by: André Kapelrud <a.kapelrud@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220606160910.6926-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When ep_idx is already non-zero, it means usually a capture stream
that is set up explicity by a fixed-format quirk, and applying the
check for generic (non-implicit-fb) sync EPs might hit incorrectly,
resulting in a bogus sync endpoint for the capture stream.
This patch adds a check for the ep_idx and skip if it's a secondary
endpoint. It's a part of the fixes for regressions on Saffire 6.
Fixes: 7b0efea4ba ("ALSA: usb-audio: Add missing ep_idx in fixed EP quirks")
Reported-and-tested-by: André Kapelrud <a.kapelrud@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220606160910.6926-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for the
USB core, but there are the usual "hot spots" of development activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes. It seems this driver will never
be finished given that the IP core is showing up in zillions
of new devices and each implementation decides to do something
different with it...
- uvc gadget driver updates as more devices start to use and
rely on this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnZGw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymQhwCeLVANsQjBcL4ys4skl+1In17y28gAn3rEZ7rQ
Yv4uP9zadUqg3Cx0vjgf
=3s5s
-----END PGP SIGNATURE-----
Merge tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
Maris found out that the quirk for TEAC devices to work around the
clock setup is needed to apply only when the base clock is changed,
e.g. from 48000-based clocks (48000, 96000, 192000, 384000) to
44100-based clocks (44100, 88200, 176400, 352800), or vice versa,
while switching to another clock with the same base clock doesn't need
the (forcible) interface setup.
This patch implements the optimization for the TEAC clock quirk to
avoid the unnecessary interface re-setup.
Fixes: 5ce0b06ae5 ("ALSA: usb-audio: Workaround for clock setup on TEAC devices")
Reported-by: Maris Abele <maris7abele@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220531130749.30357-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Devices such as the TC-Helicon GoXLR require the sync endpoint to be
configured in advance of the data endpoint in order for sound output
to work.
This patch simply changes the ordering of EP configuration to resolve
this.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215079
Signed-off-by: Craig McLure <craig@mclure.net>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220524062115.25968-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The quirk entry for Focusrite Saffire 6 had no proper ep_idx for the
capture endpoint, and this confused the driver, resulting in the
broken sound. This patch adds the missing ep_idx in the entry.
While we are at it, a couple of other entries (for Digidesign MBox and
MOTU MicroBook II) seem to have the same problem, and those are
covered as well.
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Reported-by: André Kapelrud <a.kapelrud@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220521065325.426-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Maris reported that TEAC UD-501 (0644:8043) doesn't work with the
typical "clock source 41 is not valid, cannot use" errors on the
recent kernels. The currently known workaround so far is to restore
(partially) what we've done unconditionally at the clock setup;
namely, re-setup the USB interface immediately after the clock is
changed. This patch re-introduces the behavior conditionally for TEAC
devices.
Further notes:
- The USB interface shall be set later in
snd_usb_endpoint_configure(), but this seems to be too late.
- Even calling usb_set_interface() right after
sne_usb_init_sample_rate() doesn't help; so this must be related
with the clock validation, too.
- The device may still spew the "clock source 41 is not valid" error
at the first clock setup. This seems happening at the very first
try of clock setup, but it disappears at later attempts.
The error is likely harmless because the driver retries the clock
setup (such an error is more or less expected on some devices).
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Reported-and-tested-by: Maris Abele <maris7abele@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220521064627.29292-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix following coccicheck error:
./sound/usb/endpoint.c:1671:8-10: ERROR: reference preceded by free on line 1671.
Here should be 'cp' rather than 'ip'.
Fixes: c11117b634 ("ALSA: usb-audio: Refcount multiple accesses on the single clock")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20220518021617.10114-1-wanjiabing@vivo.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a clock source is connected to multiple nodes / endpoints, the
current USB-audio driver tries to set up at each time one of them is
configured. Although it reads the current rate and updates only if it
differs, some devices seem unhappy with this behavior and spew the
errors when reading/updating the rate unnecessarily.
This patch tries to reduce the redundant clock setup by introducing a
refcount for each clock source. When the stream is actually running,
a clock rate is "locked", and it bypasses the clock and/or refuse to
change any longer.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215934
Link: https://lore.kernel.org/r/20220516104807.16482-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ai Chao