With disabling combine mode, the multiple successive
FIFO registers or non successive FIFO registers of SAI module
can work with the sdma multi fifo script.
This patch is to configure the necessary information to
the SDMA engine driver for support multi fifo script.
'words_per_fifo' is the channels for each dataline
'n_fifos_src' and 'n_fifos_dst' are the fifo number
'stride_fifos_src' and 'stride_fifos_dst' are the stride
between enable FIFOs
'maxburst' is the multiply of datalines
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1661218573-2154-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
i.MX8MQ/MN/MM/MP platforms typically have 2 AUDIO PLLs being
configured to handle 8kHz and 11kHz series audio rates.
The patch implements the functionality to select at runtime
the appropriate AUDIO PLL as function of sysclk rate.
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1656667961-1799-5-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SAI has multiple successive FIFO registers, but in some use
case the required dataline/FIFOs are not successive, so need
get such information from dts property "fsl,dataline"
fsl,dataline has 3 values for each configuration:
first one means the type: I2S(1) or DSD(2),
second one is dataline mask for 'rx',
third one is dataline mask for 'tx'.
Also set dma peripheral address and TRCE bits according to data lane.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-8-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The resource info need to be accessed by hw_params()
function for multi fifo case, the start address may
be not the FIFO0. So move it to be a member of
struct fsl_sai.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-6-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With DSD format, the pinctrl is different compare with
I2S format, because one dataline only has one channel
data, and the codec always mux the LRCLK pin to DSD
data line, and on i.MX8MQ the BCLK pin can route to
codec on DSD case for the MCLK is too high.
Add pinctrl operation that the pinctrl can be switched
on runtime according to the I2S format or DSD format
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1655451877-16382-5-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are multiple xDR and xFR registers, the index is
from 0 to 7. FSL_SAI_xDR and FSL_SAI_xFR is abandoned,
replace them with FSL_SAI_xDR0 and FSL_SAI_xFR0.
Fixes: 4f7a0728b5 ("ASoC: fsl_sai: Add support for SAI new version")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1653284661-18964-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On i.MX8MM the max register is FSL_SAI_MCTL, which is
different with previous platform, so add max_register in
soc data to distinguish platforms.
And add specific soc data for i.MX8MM
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1652688372-10274-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver tests for the hardware revision being newer than 3.1
with (sai->verid.major >= 3 && sai->verid.minor >= 1). The result
is obviously wrong for hardware revision 4.0. Fix this by storing
the full version in a single variable and comparing to that one.
No practical change at the moment as there is no 4.0 ip version
currently.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220302083428.3804687-5-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The fsl_sai driver has FSL_FMT_TRANSMITTER and FSL_FMT_RECEIVER defines
which are used in a single function only then are then only translated
into a bool 'tx' variable. Drop the defines and pass the boolean value
directly to fsl_sai_set_dai_sysclk_tr(). No functional change.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220302083428.3804687-2-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The fsl_sai driver calculates the number of pins used and enables
multiple channels if necessary. This means the SAI expects data in
one FIFO per pin. The SDMA engine only services a single FIFO, so
multi pin support doesn't work at all.
This patch enables the software combine mode in chips that support
it. With this the SAI presents only a single FIFO to the outside
and distributes the data into the different FIFOs internally.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220111081518.982437-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
As part of moving to remove the old style defines for the bus clocks update
the fsl_sai driver to use more modern terminology for clocking.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210921213542.31688-6-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
On SoCs such as i.MX7ULP, cpuidle has some levels which
may disable system/bus clocks, so need to add pm_qos to
prevent cpuidle from entering low level idles and make sure
system/bus clocks are enabled when sai is active.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1613983220-5373-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On VF610, mclk0 = bus_clk;
On i.MX6SX/6UL/6ULL/7D, mclk0 = mclk1;
On i.MX7ULP, mclk0 = bus_clk;
On i.MX8QM/8QXP, mclk0 = bus_clk;
On i.MX8MQ/8MN/8MM/8MP, mclk0 = bus_clk;
So add variable mclk0_is_mclk1 in fsl_sai_soc_data to
distinguish these platforms.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/1605768038-4582-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instantiate snd_soc_dai_driver for independent symmetric control.
Otherwise the symmetric setting may be overwritten by other
instance.
Fixes: 08fdf65e37 ("ASoC: fsl_sai: Add asynchronous mode support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1600424760-32071-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl_sai_check_version can help to parse the version info
in VERID and PARAM registers.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1600323079-5317-3-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On i.MX8MQ/i.MX8MN/i.MX8MM platform, the sai IP is upgraded.
There are some new registers and new bit definition. This
patch is to complete the register list.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1600323079-5317-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Transmit data pins will output zero when slots are masked or channels
are disabled. In CHMOD TDM mode, transmit data pins are tri-stated when
slots are masked or channels are disabled. When data pins are tri-stated,
there is noise on some channels when FS clock value is high and data is
read while fsclk is transitioning from high to low.
Signed-off-by: Cosmin-Gabriel Samoila <cosmin.samoila@nxp.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/1599112427-22038-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
One data channel is one data line. From imx7ulp, the SAI IP is
enhanced to support multiple data channels.
If there is only two channels input and slots is 2, then enable one
data channel is enough for data transfer. So enable the TCE/RCE and
transmit/receive mask register according to the input channels and
slots configuration.
Move the data channel enablement from startup() to hw_params().
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/1598958068-10552-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The fifo_depth is 64 on i.MX8QM/i.MX8QXP, 128 on i.MX8MQ, 16 on
i.MX7ULP.
Original FSL_SAI_CR1_RFW_MASK value 0x1F is not suitable for
these platform, the FIFO watermark mask should be updated
according to the fifo_depth.
Fixes: a860fac420 ("ASoC: fsl_sai: Add support for imx7ulp/imx8mq")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1596176895-28724-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
EDMA requires the period size to be multiple of maxburst. Otherwise the
remaining bytes are not transferred and thus noise is produced.
We can handle this issue by adding a constraint on
SNDRV_PCM_HW_PARAM_PERIOD_SIZE to be multiple of tx/rx maxburst value.
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190913192807.8423-2-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is to allow machine drivers to set a certain bitclk rate
which might not be exactly rate * frame size.
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190830215910.31590-1-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
New IP version introduces Version ID and Parameter registers
and optionally added Timestamp feature.
VERID and PARAM registers are placed at the top of registers
address space and some registers are shifted according to
the following table:
Tx/Rx data registers and Tx/Rx FIFO registers keep their
addresses, all other registers are shifted by 8.
SAI Memory map is described in chapter 13.10.4.1.1 I2S Memory map
of the Reference Manual [1].
In order to make as less changes as possible we attach an offset
to each register offset to each changed register definition. The
offset is read from each board private data.
[1]https://cache.nxp.com/secured/assets/documents/en/reference-manual/IMX8MDQLQRM.pdf?__gda__=1563728701_38bea7f0f726472cc675cb141b91bec7&fileExt=.pdf
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
[initial coding in the NXP internal tree]
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
[bugfixing and cleanups]
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
[adapted to linux-next]
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190806151214.6783-4-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tx channel enable (TCE) / Rx channel enable (RCE) bits
enable corresponding data channel for Tx/Rx operation.
Because SAI supports up the 8 channels TCE/RCE occupy
up the 8 bits inside TCR3/RCR3 registers we need to extend
the mask to reflect this.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190806151214.6783-3-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SAI IP supports up to 8 data lines. The configuration of
supported number of data lines is decided at SoC integration
time.
This patch adds definitions for all related data TX/RX registers:
* TDR0..7, Transmit data register
* TFR0..7, Transmit FIFO register
* RDR0..7, Receive data register
* RFR0..7, Receive FIFO register
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190806151214.6783-2-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA request schould be triggered as soon as the FIFO has space
for another burst. As different versions of the SAI block have
different FIFO sizes, the watrmark level needs to be derived from
version specific data.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Link: https://lore.kernel.org/r/20190717105635.18514-3-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
New revisions of the SAI IP block have even more differences that need
be taken into account by the driver. To avoid sprinking compatible
checks all over the driver move the current differences into of_match_data.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20190717105635.18514-2-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add tdm slots operation support. If tdm slots and slot width have
been configured in machine driver, we should use these values.
Otherwise, using relevant channels and word length to set slots
and slot width.
SAI will generate BCLK depends on sample rate, slots and slot width.
And there may be unused BCLK cycles before each LRCLK transition.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are too much noise about the typos for fsl's drivers. So I fix
all the typos here in this patch in almost every file I touched.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 32 bit word length support. There are no code changes required
in the SAI driver since it has already wirten the word width to the
corresponding register.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When sai works on master mode, set its bit clock and frame clock.
SAI has 4 MCLK source, bus clock, MCLK1, MCLK2 and MCLK3. fsl_sai_set_bclk
will select proper MCLK source, then calculate and set the bit clock divider.
After fsl_sai_set_bclk, enable the selected mclk in hw_params(), and add
hw_free() to disable the mclk.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'big-endian-data' property is originally used to indicate whether the
LSB firstly or MSB firstly will be transmitted to the CODEC or received
from the CODEC, and there has nothing relation to the memory data.
Generally, if the audio data in big endian format, which will be using the
bytes reversion, Here this can only be used to bits reversion.
So using the 'lsb-first' instead of 'big-endian-data' can make the code
to be readable easier and more easy to understand what this property is
used to do.
This property used for configuring whether the LSB or the MSB is transmitted
first for the fifo data.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SAI supports these operation modes:
1) asynchronous mode
Both Tx and Rx are set to be asynchronous.
2) synchronous mode (Rx sync with Tx)
Tx is set to be asynchronous, Rx is set to be synchronous.
3) synchronous mode (Tx sync with Rx)
Rx is set to be asynchronous, Tx is set to be synchronous.
4) synchronous mode (Tx/Rx sync with another SAI's Tx)
5) synchronous mode (Tx/Rx sync with another SAI's Rx)
* 4) and 5) are beyond this patch because they are related with another SAI.
As the initial version of this SAI driver, it supported 2) as default while
the others were totally missing.
So this patch just adds supports for 1) and 3).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds software reset code in dai_probe() so as to make a true init
by clearing SAI's internal logic, including the bit clock generation, status
flags, and FIFO pointers.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SAI mainly has the following clocks:
bus clock
control and configure registers and to generate synchronous
interrupts and DMA requests.
mclk1, mclk2, mclk3
to generate the bit clock when the receiver or transmitter is
configured for an internally generated bit clock.
So this patch adds these clocks and their clock controls to the driver.
[ To concern the old DTB cases, I've added a bit of extra code to make
the driver compatible with them. And by marking clock NULL if failed
to get, the clk_prepare() or clk_get_rate() would easily return 0
so no further path should be broken. -- by Nicolin ]
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The next coming i.MX6 Solo X SoC also contains SAI module while we use
imp_pcm_init() for i.MX platform.
So this patch adds one compatible route for imx6sx and updates the DT
doc accordingly.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We only enable one side interrupt for each stream since over/underrun
on the opposite stream would be resulted from what we previously did,
enabling TERE but remaining FRDE disabled, even though the xrun on the
opposite direction will not break the current stream.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The current trigger() has two crucial problems:
1) The DMA request enabling operations (FSL_SAI_CSR_FRDE) for Tx and Rx are
now totally exclusive: It would fail to run simultaneous Tx-Rx cases.
2) The TERE disabling operation depends on an incorrect condition -- active
reference count that only gets increased in snd_pcm_open() and decreased
in snd_pcm_close(): The TERE would never get cleared.
So this patch overwrites the trigger function by following these rules:
A) We continue to support tx-async-while-rx-sync-to-tx case alone, which's
originally limited by this fsl_sai driver, but we make the code easy to
modify for the further support of the opposite case.
B) We enable both TE and RE for PLAYBACK stream or CAPTURE stream but only
enabling the DMA request bit (FSL_SAI_CSR_FRDE) of the current direction
due to the requirement of SAI -- For tx-async-while-rx-sync-to-tx case,
the receiver is enabled only when both the transmitter and receiver are
enabled.
Tested cases:
a) aplay test.wav -d5
b) arecord -r44100 -c2 -fS16_LE test.wav -d5
c) arecord -r44100 -c2 -fS16_LE -d5 | aplay
d) (aplay test2.wav &); sleep 1; arecord -r44100 -c2 -fS16_LE test.wav -d1
e) (arecord -r44100 -c2 -fS16_LE test.wav -d5 &); sleep 1; aplay test.wav -d1
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It's quite cricial to clear error flags because SAI might hang if getting
FIFO underrun during playback (I haven't confirmed the same issue on Rx
overflow though).
So this patch enables those irq and adds isr() to clear the flags so as to
keep playback entirely safe.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
o Add SND_SOC_DAIFMT_DSP_A support.
o Add SND_SOC_DAIFMT_DSP_B support.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This adds Freescale SAI ASoC Audio support.
This implementation is only compatible with device tree definition.
Features:
o Supports playback/capture
o Supports 16/20/24 bit PCM
o Supports 8k - 96k sample rates
o Supports master and slave mode.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
