NPCM can support up to 10 own slave addresses. In practice, only one
address is actually being used. In order to access addresses 2 and above,
need to switch register banks. The switch needs spinlock.
To avoid using spinlock for this useless feature removed support of SA >=
2. Also fix returned slave event enum.
Remove some comment since the bank selection is not required. The bank
selection is not required since the supported slave addresses are reduced.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The "data->block[0]" variable comes from the user and is a number
between 0-255. It needs to be capped to prevent writing beyond the end
of dma_buffer[].
Fixes: 5e9a97b1f4 ("i2c: ismt: Adding support for I2C_SMBUS_BLOCK_PROC_CALL")
Reported-and-tested-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I2C has only driver updates for 5.19. Bigger changes are for Meson,
NPCM, and R-Car, but there are also changes all over the place.
-----BEGIN PGP SIGNATURE-----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=vdUW
-----END PGP SIGNATURE-----
Merge tag 'i2c-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Only driver updates for 5.19.
Bigger changes are for Meson, NPCM, and R-Car, but there are also
changes all over the place"
* tag 'i2c-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c: meson: fix typo in comment
i2c: rcar: use flags instead of atomic_xfer
i2c: rcar: REP_AFTER_RD is not a persistent flag
i2c: rcar: use BIT macro consistently
i2c: qcom-geni: remove unnecessary conditions
i2c: mt7621: Use devm_platform_get_and_ioremap_resource()
i2c: rcar: refactor handling of first message
i2c: rcar: avoid race condition with SMIs
i2c: xiic: Correct the datatype for rx_watermark
i2c: rcar: fix PM ref counts in probe error paths
i2c: npcm: Handle spurious interrupts
i2c: npcm: Correct register access width
i2c: npcm: Add tx complete counter
i2c: npcm: Fix timeout calculation
i2c: npcm: Remove unused variable clk_regmap
i2c: npcm: Change the way of getting GCR regmap
i2c: xiic: Fix Tx Interrupt path for grouped messages
i2c: xiic: Fix coding style issues
i2c: xiic: return value of xiic_reinit
i2c: cadence: Increase timeout per message if necessary
...
Due to i2c->adap.dev.fwnode not being set, ACPI_COMPANION() wasn't properly
found for TWSI controllers.
Signed-off-by: Szymon Balcerak <sbalcerak@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c-rcar already has priv->flags. This patch adds a new persistent flag
ID_P_NOT_ATOMIC and uses it to save the extra variable. The negation of
the logic was done to make the code more readable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[wsa: negated the logic, rebased, updated the commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Previous refactoring makes it easy now to convert the above flag to a
non-persistent one. This is more appropriate and easier to maintain.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Before sending a MSI the hardware writes information pertinent to the
interrupt cause to a memory location pointed by SMTICL register. This
memory holds three double words where the least significant bit tells
whether the interrupt cause of master/target/error is valid. The driver
does not use this but we need to set it up because otherwise it will
perform DMA write to the default address (0) and this will cause an
IOMMU fault such as below:
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set
To prevent this from happening, provide a proper DMA buffer for this
that then gets mapped by the IOMMU accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We know that "ret" is a negative error code at this point so there is
no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix the missing clk_disable_unprepare() before return
from mtk_i2c_probe() in the error handling case.
Fixes: d04913ec5f ("i2c: mt7621: Add MediaTek MT7621/7628/7688 I2C driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
After moving ICMSR handling to interrupt handlers previously to fix a
race condition, we can now also move ICMSR handling for the first
message out of the function to prepare a message. By introducing a
seperate function to initialize the first message, we can not only
remove some code duplication but the remaining code is also easier to
follow. The function to prepare a message is much simpler without ICMSR
handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A customer experienced a race condition with 'repeated starts' when a
System Management Interrupt took over for 30us and more. The problem was
that during the SMI a new MAT interrupt came in because we set up the
'repeated start' condition. But the old one was not acknowledged yet.
So, when it was acknowledged after the SMI, the new MAT interrupt was
lost, confusing the state machine of the driver.
The fix consists of two parts. First, we do not clear the status
register for 'repeated starts' when preparing the next message anymore.
The interrupt handlers for sending and receiving data is now solely
responsible for that and it makes the code easier to follow, in fact.
Secondly, clearing the status register is now split up to handle MAT
interrupts independently. This avoids the race condition because the old
MAT interrupt will be now cleared before we initiate the "repeated
start" condition.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The message length data type should be u16 as per the i2c_msg structure.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We have to take care of ID_P_PM_BLOCKED when bailing out during probe.
Fixes: 7ee24eb508 ("i2c: rcar: disable PM in multi-master mode")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On some platforms in rare cases (1 to 100,000 transactions),
the i2c gets a spurious interrupt which means that we enter an interrupt
but in the interrupt handler we don't find any status bit that points to
the reason we got this interrupt.
This may be a case of a rare HW issue or signal integrity issue that is
still under investigation.
In order to overcome this we are doing the following:
1. Disable incoming interrupts in master mode only when slave mode is not
enabled.
2. Clear end of busy (EOB) after every interrupt.
3. Clear other status bits (just in case since we found them cleared)
4. Return correct status during the interrupt that will finish the
transaction.
On next xmit transaction if the bus is still busy the master will issue a
recovery process before issuing the new transaction.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The SMBnCTL3 register is 8-bit wide and the 32-bit access was always
incorrect, but simply didn't cause a visible error on the 32-bit machine.
On the 64-bit machine, the kernel message reports that ESR value is
0x96000021. Checking Arm Architecture Reference Manual Armv8 suggests that
it's the alignment fault.
SMBnCTL3's address is 0xE.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
tx_complete counter is used to indicate successful transaction count.
Similar counters for failed tx were previously added.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use adap.timeout for timeout calculation instead of hard-coded
value of 35ms.
Fixes: 56a1485b10 ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove unused variable clk_regmap.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change the way of getting NPCM system manager reigster (GCR)
and still maintain the old mechanism as a fallback if getting
nuvoton,sys-mgr fails while working with the legacy devicetree
file.
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When a group of messages are sent from user space as a set, if
the last message has less than Tx FIFO DEPTH number of bytes
to transfer, Tx half empty interrupt is triggered continuously
from the hardware. It is due to Bus not busy interrupt coming
along with Tx half empty and tx empty.
Hence, service the Tx interrupts before Bus not busy interrupt
to update the i2c message status correctly.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Most of these stuff are reported by checkpatch.
But fixes are:
- Incorrect indetation
- Missing blank line after variable declaration
- Additional ()
- Missing spaces around +
- Missing parenthesis when if has them
- Newlines
- Remove MODULE_ALIAS - none is really using it
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Check the return value of xiic_reinit.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Timeout as 1 second sets an upper limit on the length
of the transfer executed, but there is no maximum length
of a write or read message set in i2c_adapter_quirks for
this controller.
This upper limit affects devices that require sending
large firmware blobs over I2C.
To remove that limitation, calculate the minimal time
necessary, plus some wiggle room, for every message and
use it instead of the default one second, if more than
one second.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It's more logical to read these get timing parameters ACPI method calls
sorted by speed categories in increasing order: Standard-mode,
Fast-mode, Fast-mode Plus and High-speed mode.
Originally these were in order after commit a92ec1746f
("i2c: designware: get fast plus and high speed *CNT configuration") but
got mixed up over the years.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Clang warns:
drivers/i2c/busses/i2c-at91-master.c:707:6: warning: variable 'dma_buf' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
if (dev->use_dma) {
^~~~~~~~~~~~
drivers/i2c/busses/i2c-at91-master.c:717:27: note: uninitialized use occurs here
i2c_put_dma_safe_msg_buf(dma_buf, m_start, !ret);
^~~~~~~
Initialize dma_buf to NULL, as i2c_put_dma_safe_msg_buf() is a no-op
when the first argument is NULL, which will work for the !dev->use_dma
case.
Fixes: 03fbb903c8 ("i2c: at91: use dma safe buffers")
Link: https://github.com/ClangBuiltLinux/linux/issues/1629
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix the missing clk_disable_unprepare() before return
from meson_i2c_probe() in the error handling case.
Fixes: a57f9b4dd6 ("i2c: meson: Use 50% duty cycle for I2C clock")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
powerpc's asm/prom.h brings some headers that it doesn't
need itself.
In order to clean it up, first add missing headers in
users of asm/prom.h
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The supplied buffer might be on the stack and we get the following error
message:
[ 3.312058] at91_i2c e0070600.i2c: rejecting DMA map of vmalloc memory
Use i2c_{get,put}_dma_safe_msg_buf() to get a DMA-able memory region if
necessary.
Fixes: 60937b2cdb ("i2c: at91: add dma support")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Especially (but not only) during probe, it may happen that multiple
devices are communicating via i2c (or multiple i2c busses) and
sometimes while others are probing asynchronously.
For example, a Cr50 TPM may be filling entropy (or userspace may be
reading random data) while the rt5682 (i2c) codec driver reads/sets
some registers, like while getting/setting a clock's rate, which
happens both during probe and during system operation.
In this driver, the mtk_i2c_transfer() function (which is the i2c
.master_xfer() callback) was granularly managing the clocks by
performing a clk_bulk_prepare_enable() to start them and its inverse.
This is not only creating possible circular locking dependencies in
the some cases (like former explanation), but it's also suboptimal,
as clk_core prepare/unprepare operations are using mutex locking,
which creates a bit of unwanted overhead (for example, i2c trackpads
will call master_xfer() every few milliseconds!).
With this commit, we avoid both the circular locking and additional
overhead by changing how we handle the clocks in this driver:
- Prepare the clocks during probe (and PM resume)
- Enable/disable clocks in mtk_i2c_transfer()
- Unprepare the clocks only for driver removal (and PM suspend)
For the sake of providing a full explanation: during probe, the
clocks are not only prepared but also enabled, as this is needed
for some hardware initialization but, after that, we are disabling
but not unpreparing them, leaving an expected state for the
aforementioned clock handling strategy.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Adjust retry period and timeout values for x86-PSP mailbox based on the
typical I2C traffic generated by PSP. In order to limit the possibility
of timeouts, x86 should reduce the interval between retries as well as
increase overall time after which it gives up.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix:
drivers/i2c/busses/i2c-ismt.c: In function ‘ismt_hw_init’:
drivers/i2c/busses/i2c-ismt.c:770:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_400K:
^~~~
drivers/i2c/busses/i2c-ismt.c:773:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_1M:
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The duty cycle of 33% is less than the required
by the I2C specs for the LOW period of the SCL
clock.
Move the duty cyle to 50% for 100Khz or lower
clocks, and (40% High SCL / 60% Low SCL) duty
cycle for clocks above 100Khz.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Differentiate between masks and shifts
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With this feature added, SMBus Block reads and Proc calls are now
supported. This patch is the best of two independent developments by
Wolfram and Bhuvanesh + Andrew, refactored again by Wolfram.
Signed-off-by: Bhuvanesh Surachari <bhuvanesh_surachari@mentor.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Sparse has warned us about wrong address space for user pointers:
i2c-dev.c:561:50: warning: incorrect type in initializer (different address spaces)
i2c-dev.c:561:50: expected unsigned char [usertype] *buf
i2c-dev.c:561:50: got void [noderef] __user *
Force cast the pointer to (__u8 *) that is used by I²C core code.
Note, this is an additional fix to the previously addressed similar issue
in the I2C_RDWR case in the same function.
Fixes: 3265a7e6b4 ("i2c: dev: Add __user annotation")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If dev_set_name() fails, the dev_name() is null, check the return
value of dev_set_name() to avoid the null-ptr-deref.
Fixes: 1413ef638a ("i2c: dev: Fix the race between the release of i2c_dev and cdev")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The GPI DMA engine driver can be compiled as a module, in which case the
likely probe deferral "error" shows up in the kernel log. Switch to
using dev_err_probe() to silence this warning and to ensure that
"devices_deferred" in debugfs carries this information.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i.MX8MP Mask Set Errata for Mask 1P33A, Rev. 2.0 has description of
errata ERR007805 as below. This errata is found on all MX8M{M,N,P,Q},
MX7{S,D}, MX6{UL{,L,Z},S{,LL,X},S,D,DL,Q,DP,QP} . MX7ULP, MX8Q, MX8X
are not affected. MX53 and older status is unknown, as the errata
first appears in MX6 errata sheets from 2016 and the latest errata
sheet for MX53 is from 2015. Older SoC errata sheets predate the
MX53 errata sheet. MX8ULP and MX9 status is unknown as the errata
sheet is not available yet.
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
Implement the workaround by matching on the affected SoC specific
compatible strings and by limiting the maximum bus frequency in case
the SoC is affected.
Signed-off-by: Marek Vasut <marex@denx.de>
To: linux-i2c@vger.kernel.org
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Wait for completion of write transfers before returning from the driver.
At first sight it may seem advantageous to leave write transfers queued
for the controller to carry out on its own time, but there's a couple of
issues with it:
* Driver doesn't check for FIFO space.
* The queued writes can complete while the driver is in its I2C read
transfer path which means it will get confused by the raising of
XEN (the 'transaction ended' signal). This can cause a spurious
ENODATA error due to premature reading of the MRXFIFO register.
Adding the wait fixes some unreliability issues with the driver. There's
some efficiency cost to it (especially with pasemi_smb_waitready doing
its polling), but that will be alleviated once the driver receives
interrupt support.
Fixes: beb58aa39e ("i2c: PA Semi SMBus driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
- tracepoints when Linux acts as an I2C client
- added support for AMD PSP
- whole subsystem now uses generic_handle_irq_safe()
- piix4 driver gained MMIO access enabling so far missed controllers
with AMD chipsets
- a bulk of device driver updates, refactorization, and fixes.
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (61 commits)
i2c: mux: demux-pinctrl: do not deactivate a master that is not active
i2c: meson: Fix wrong speed use from probe
i2c: add tracepoints for I2C slave events
i2c: designware: Remove code duplication
i2c: cros-ec-tunnel: Fix syntax errors in comments
MAINTAINERS: adjust XLP9XX I2C DRIVER after removing the devicetree binding
i2c: designware: Mark dw_i2c_plat_{suspend,resume}() as __maybe_unused
i2c: mediatek: Add i2c compatible for Mediatek MT8168
dt-bindings: i2c: update bindings for MT8168 SoC
i2c: mt65xx: Simplify with clk-bulk
i2c: i801: Drop two outdated comments
i2c: xiic: Make bus names unique
i2c: i801: Add support for the Process Call command
i2c: i801: Drop useless masking in i801_access
i2c: tegra: Add SMBus block read function
i2c: designware: Use the i2c_mark_adapter_suspended/resumed() helpers
i2c: designware: Lock the adapter while setting the suspended flag
i2c: mediatek: remove redundant null check
i2c: mediatek: modify bus speed calculation formula
i2c: designware: Fix improper usage of readl
...
power-supply core:
- Introduce "Bypass" charging type used by USB PPS standard
- Refactor power_supply_set_input_current_limit_from_supplier()
- Add fwnode support to power_supply_get_battery_info()
Drivers:
- ab8500: continue migrating towards using standard core APIs
- axp288 fuel-gauge: refactor driver to be fully resource managed
- battery-samsung-sdi: new in-kernel provider for (constant) Samsung battery info
- bq24190: disable boost regulator on shutdown
- bq24190: add support for battery-info on ACPI based systems
- bq25890: prepare driver for usage on ACPI based systems
- bq25890: add boost regulator support
- cpcap-battery: add NVMEM based battery detection support
- injoinic ip5xxx: new driver for power bank IC
- upi ug3105: new battery driver
- misc. small improvements and fixes
-----BEGIN PGP SIGNATURE-----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=OiYc
-----END PGP SIGNATURE-----
Merge tag 'for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- Introduce "Bypass" charging type used by USB PPS standard
- Refactor power_supply_set_input_current_limit_from_supplier()
- Add fwnode support to power_supply_get_battery_info()
Drivers:
- ab8500: continue migrating towards using standard core APIs
- axp288 fuel-gauge: refactor driver to be fully resource managed
- battery-samsung-sdi: new in-kernel provider for (constant) Samsung
battery info
- bq24190: disable boost regulator on shutdown
- bq24190: add support for battery-info on ACPI based systems
- bq25890: prepare driver for usage on ACPI based systems
- bq25890: add boost regulator support
- cpcap-battery: add NVMEM based battery detection support
- injoinic ip5xxx: new driver for power bank IC
- upi ug3105: new battery driver
- misc small improvements and fixes"
* tag 'for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (94 commits)
power: ab8500_chargalg: Use CLOCK_MONOTONIC
power: supply: Add a driver for Injoinic power bank ICs
dt-bindings: trivial-devices: Add Injoinic power bank ICs
dt-bindings: vendor-prefixes: Add Injoinic
power: supply: ab8500: Remove unused variable
power: supply: da9150-fg: Remove unnecessary print function dev_err()
power: supply: ab8500: fix a handful of spelling mistakes
power: supply: ab8500_fg: Account for line impedance
dt-bindings: power: supply: ab8500_fg: Add line impedance
power: supply: axp20x_usb_power: fix platform_get_irq.cocci warnings
power: supply: axp20x_ac_power: fix platform_get_irq.cocci warning
power: supply: wm8350-power: Add missing free in free_charger_irq
power: supply: wm8350-power: Handle error for wm8350_register_irq
power: supply: Static data for Samsung batteries
power: supply: ab8500_fg: Use VBAT-to-Ri if possible
power: supply: Support VBAT-to-Ri lookup tables
power: supply: ab8500: Standardize BTI resistance
power: supply: ab8500: Standardize alert mode charging
power: supply: ab8500: Standardize maintenance charging
power: supply: bq24190_charger: Delay applying charge_type changes when OTG 5V Vbus boost is on
...
Attempting to rollback the activation of the current master when
the current master has not been activated is bad. priv->cur_chan
and priv->cur_adap are both still zeroed out and the rollback
may result in attempts to revert an of changeset that has not been
applied and do result in calls to both del and put the zeroed out
i2c_adapter. Maybe it crashes, or whatever, but it's bad in any
case.
Fixes: e9d1a0a41d ("i2c: mux: demux-pinctrl: Fix an error handling path in 'i2c_demux_pinctrl_probe()'")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Having meson_i2c_set_clk_div after i2c_add_adapter
causes issues for client drivers that try to use
the bus before the requested speed is applied.
The bus can be used just after i2c_add_adapter, so
move i2c_add_adapter to the final step as
meson_i2c_set_clk_div needs to be called before
the bus is used.
Fixes: 09af1c2fa4 ("i2c: meson: set clock divider in probe instead of setting it for each transfer")
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Simplify code by moving common part to one function.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Delete the redundant word 'to'
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
[wsa: fixed prefix in subject]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When CONFIG_PM is set but CONFIG_PM_SLEEP is not, two compiler warnings
appear:
drivers/i2c/busses/i2c-designware-platdrv.c:444:12: error: unused function 'dw_i2c_plat_suspend' [-Werror,-Wunused-function]
static int dw_i2c_plat_suspend(struct device *dev)
^
drivers/i2c/busses/i2c-designware-platdrv.c:465:12: error: unused function 'dw_i2c_plat_resume' [-Werror,-Wunused-function]
static int dw_i2c_plat_resume(struct device *dev)
^
2 errors generated.
These functions are only used in SET_LATE_SYSTEM_SLEEP_PM_OPS(), which
is defined as empty when CONFIG_PM_SLEEP is not defined. Mark the
functions as __maybe_unused to make it clear that these functions might
be unused in this configuration.
Fixes: c57813b8b2 ("i2c: designware: Lock the adapter while setting the suspended flag")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add i2c compatible for MT8168. Compare to MT2712 i2c controller,
MT8168 need to synchronize signal with dma.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since depending on the SoC or specific bus functionality some clocks
may be optional, we cannot get the benefit of using devm_clk_bulk_get()
but, by migrating to clk-bulk, we are able to remove the custom functions
mtk_i2c_clock_enable() and mtk_i2c_clock_disable(), increasing common
APIs usage, hence (lightly) decreasing kernel footprint.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
* Timeouts are reported even in interrupt mode since commit
b3b8df9772 ("i2c: i801: Use wait_event_timeout to wait for
interrupts") so drop the comment which claims this only happens in
polled mode.
* xact does not include the PEC bit, as the driver does not support
software PEC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This driver is for an FPGA logic core, so there can be arbitrarily many
instances of the bus on a given system. Previously all of the I2C bus
names were "xiic-i2c" which caused issues with lm_sensors when trying to
map human-readable names to sensor inputs because it could not properly
distinguish the busses, for example. Append the platform device name to
the I2C bus name so it is unique between different instances.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The Process Call command is implemented by the hardware since the very
first Intel 82801 chipset, and trivial to support. Oscar Romero
Matamala from the Georgia Institute of Technology told me it is needed
for an experiment his team is working on at the moment, so let's just
add support for it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I went all the way back to kernel 2.6.12 and that masking was never
needed. I suppose it was there in anticipation of software PEC
support, but that was never added to the driver (and never will be,
as this is made obsolete by hardware PEC).
I'm also removing initialization to 0, which is not needed either,
and would prevent the compiler from reporting an actual usage of
uninitialized variables.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use the i2c_mark_adapter_suspended/resumed() i2c-core helpers and rely
on the i2c-core's suspended checking instead of using DIY code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Lock the adapter while setting the suspended flag, to ensure that other
locked code always sees the change immediately, rather then possibly using
a stale value.
This involves splitting the suspend/resume callbacks into separate runtime
and normal suspend/resume calls. This is necessary because i2c_dw_xfer()
will get called by the i2c-core with the adapter locked and it in turn
calls the runtime-resume callback through pm_runtime_get_sync().
So the runtime versions of the suspend/resume callbacks cannot take
the adapter-lock. Note this patch simply makes the runtime suspend/resume
callbacks not deal with the suspended flag at all. During runtime the
pm_runtime_get_sync() from i2c_dw_xfer() will always ensure that the
adapter is resumed when necessary.
The suspended flag check is only necessary to check proper suspend/resume
ordering during normal suspend/resume which makes the pm_runtime_get_sync()
call a no-op.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Because clk_disable_unprepare already checked NULL clock parameter,
so the additional checks are unnecessary, just remove it
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When clock-div is 0 or greater than 1, the bus speed
calculated by the old speed calculation formula will be
larger than the target speed. So we update the formula.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Kernel test robot reported incorrect type in argument 1 of readl(), but
more importantly it brought attention that MMIO accessor shouldn't be
used in this case, since req->hdr.status is part of a command-response
buffer in system memory.
Since its value may be altered by PSP outside of the scope of current
thread (somehow similar to IRQ handler case), we need to use
READ_ONCE() to ensure compiler won't optimize this call.
Fix also 'status' variable type to reflect that corresponding field in
command-response buffer is platform-independent u32.
Fixes: 78d5e9e299 ("i2c: designware: Add AMD PSP I2C bus support")
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
QUP Serial engines supports data transfers thru FIFO mode, SE DMA mode
and lastly GPI DMA mode. Former two are already supported and this adds
supports for the last mode.
In GPI DMA mode, the firmware is issued commands by driver to perform
DMA and setup the serial port.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Read reset phandle as optional instead of exclusive so that all the DT's
passing the reset phandle can be used to assert/deassert the reset line.
With this change we don't have to differentiate the RZ/G2L SoC.
With the above changes we no longer need the "renesas,riic-r9a07g044"
compatible string, so drop it from riic_i2c_dt_ids[]. No changes are
required to the r9a07g044.dtsi as we already have "renesas,riic-rz" as a
fallback compatible string.
While at it, check the return code of reset_control_deassert() as it might
fail and also add a devres action to assert the reset line.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of manually disabling interrupts before invoking use
generic_handle_irq_safe() which can be invoked with enabled and disabled
interrupts.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c-i801 driver invokes i2c_handle_smbus_host_notify() from his
interrupt service routine. On PREEMPT_RT i2c-i801's handler is forced
threaded with enabled interrupts which leads to a warning by
handle_irq_event_percpu() assuming that irq_default_primary_handler()
enabled interrupts.
i2c-i801's interrupt handler can't be made non-threaded because the
interrupt line is shared with other devices.
Use generic_handle_irq_safe() which can invoked with disabled and enabled
interrupts.
Reported-by: Michael Below <below@judiz.de>
Link: https://bugs.debian.org/1002537
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
An I²C adapter might be instantiated without parent. In such case
there is no property can be retrieved. Skip SMBus alert setup when
this happens.
Fixes: a263a84088 ("i2c: smbus: Use device_*() functions instead of of_*()")
Reported-by: syzbot+0591ccf54ee05344e4eb@syzkaller.appspotmail.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c618 ("i2c: brcmstb: Adding support for CM and DSL SoCs")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add QCOM SM8450 specific compatible for CCI controller, which is
equal to CCI controllers found on QCOM SDM845 and QCOM SM8250 SoCs.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Drop I2C device-probing classes from platform variant of the PASemi
controller as it is only used on platforms where I2C devices should
be instantiated in devicetree. (The I2C_CLASS_DEPRECATED flag is not
raised as up to this point no devices relied on the old behavior.)
Fixes: d88ae2932d ("i2c: pasemi: Add Apple platform driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Eliminate the following coccicheck warnings:
./drivers/i2c/busses/i2c-designware-amdpsp.c:172:2-3: Unneeded semicolon
./drivers/i2c/busses/i2c-designware-amdpsp.c:245:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jan Dabros <jsd@semihalf.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of open coded variant switch to use i2c_new_ccgx_ucsi().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It's fine to call dev_err_probe() in ->probe() when error code is known.
Convert the driver to use dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use temporary variable for struct device to make code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of open coded variant switch to use i2c_new_ccgx_ucsi().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Introduce a common module to provide an API to instantiate UCSI device
for Cypress CCGx Type-C controller. Individual bus drivers need to select
this one on demand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add SMBus PCI ID on Intel Raptor Lake PCH-S.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c_setup_smbus_alert() is only needed within the I2C core, so no need
to expose it to other modules.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
There is a minor chance for a race, if a pointer to an i2c-bus subnode
is stored and then reused after releasing its reference, and it would
be sufficient to get one more reference under a loop over children
subnodes.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If i2c_add_adapter() fails to add an I2C adapter found on QCOM CCI
controller, on error path i2c_del_adapter() is still called.
Fortunately there is a sanity check in the I2C core, so the only
visible implication is a printed debug level message:
i2c-core: attempting to delete unregistered adapter [Qualcomm-CCI]
Nevertheless it would be reasonable to correct the probe error path.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
BCM4908 SoCs use the same I2C hardware block as STB and BCM63xx devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for the I2C Bus Interface on R-Car Gen4 SoCs (e.g. R-Car
S4-8) by matching on a family-specific compatible value.
While I2C on R-Car Gen4 does support some extra features (Slave Clock
Stretch Select), for now it is treated the same as I2C on R-Car Gen3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: removed incorrect "FM+" from commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Implement an I2C controller sharing mechanism between the host (kernel)
and PSP co-processor on some platforms equipped with AMD Cezanne SoC.
On these platforms we need to implement "software" i2c arbitration.
Default arbitration owner is PSP and kernel asks for acquire as well
as inform about release of the i2c bus via mailbox mechanism.
+---------+
<- ACQUIRE | |
+---------| CPU |\
| | | \ +----------+ SDA
| +---------+ \ | |-------
MAILBOX +--> | I2C-DW | SCL
| +---------+ | |-------
| | | +----------+
+---------| PSP |
<- ACK | |
+---------+
+---------+
<- RELEASE | |
+---------| CPU |
| | | +----------+ SDA
| +---------+ | |-------
MAILBOX +--> | I2C-DW | SCL
| +---------+ / | |-------
| | | / +----------+
+---------| PSP |/
<- ACK | |
+---------+
The solution is similar to i2c-designware-baytrail.c implementation, where
we are using a generic i2c-designware-* driver with a small "wrapper".
In contrary to baytrail semaphore implementation, beside internal
acquire_lock() and release_lock() methods we are also applying quirks to
lock_bus() and unlock_bus() global adapter methods. With this in place
all i2c clients drivers may lock i2c bus for a desired number of i2c
transactions (e.g. write-wait-read) without being aware of that such bus
is shared with another entity.
Modify i2c_dw_probe_lock_support() to select correct semaphore
implementation at runtime, since now we have more than one available.
Configure new matching ACPI ID "AMDI0019" and register
ARBITRATION_SEMAPHORE flag in order to distinguish setup with PSP
arbitration.
Add myself as a reviewer for I2C DesignWare in order to help with reviewing
and testing possible changes touching new i2c-designware-amdpsp.c module.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: removed unneeded blank line and curly braces]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
All accesses to controller's registers should be protected on
probe, disable and xfer paths. This is needed for i2c bus controllers
that are shared with but not controller by kernel.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Enable EFCH MMIO using check for SMBus PCI revision ID value 0x51 or
greater. This PCI revision ID check will enable family 17h and future
AMD processors with the same EFCH SMBus controller HW.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
AMD processors include registers capable of selecting between 2 SMBus
ports. Port selection is made during each user access by writing to
FCH::PM::DECODEEN[smbus0sel]. Change the driver to use MMIO during
SMBus port selection because cd6h/cd7h port I/O is not available on
later AMD processors.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The EFCH SMBus controller's base address is determined using details in
FCH::PM::DECODEEN[smbusasfiobase] and FCH::PM::DECODEEN[smbusasfioen].These
register fields were accessed using cd6h/cd7h port I/O. cd6h/cd7h port I/O
is no longer available in later AMD processors. Change base address
detection to use MMIO instead of port I/O cd6h/cd7h.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
EFCH cd6h/cd7h port I/O may no longer be available on later AMD
processors and it is recommended to use MMIO instead. Update the
request and release functions to support MMIO.
MMIO request/release and mmapping require details during cleanup.
Add a MMIO configuration structure containing resource and vaddress
details for mapping the region, accessing the region, and releasing
the region.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
[wsa: rebased after fixup in previous patch]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move port selection code into a separate function. Refactor is in
preparation for following MMIO changes.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move SMBus controller base address detection into function. Refactor
is in preparation for following MMIO changes.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Move duplicated region request and release code into a function. Move is
in preparation for following MMIO changes.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
[wsa: added missing curly brace]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace number constant with #define to improve readability and
maintainability.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The comments in this driver have a few typos. Let's fix them.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: tali.perry@nuvoton.com
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace acpi_bus_get_device() that is going to be dropped with
acpi_fetch_acpi_dev().
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The CLKT register contains at poweron 0x40, which at our typical 100kHz
bus rate means .64ms. But there is no specified limit to how long devices
should be able to stretch the clocks, so just disable the timeout. We
still have a timeout wrapping the entire transfer.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
BugLink: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some resource should be released if an error occurs in
'bcm2835_i2c_probe()'.
Add an error handling path and the needed 'clk_disable_unprepare()' and
'clk_rate_exclusive_put()' calls.
While at it, rework the bottom of the function to use this newly added
error handling path and have an explicit and more standard "return 0;" at
the end of the normal path.
Fixes: bebff81fb8 ("i2c: bcm2835: Model Divider in CCF")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[wsa: rebased]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL. So, if it fails, the 32 bits case will also
fail for the same reason.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Nehal Bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c-controller on the Cherry Trail - Whiskey Cove PMIC is special
in that it is always connected to the I2C charger IC of the board on
which the PMIC is used; and the charger IC is not described in ACPI,
so the i2c-cht-wc code needs to instantiate an i2c-client for it itself.
So far this was hardcoded to instantiate an i2c-client for the
bq24292i, with all properties, etc. set to match how this charger
is used on the GPD win and GPD pocket devices.
There is a rudimentary check to make sure the ACPI tables are at least
somewhat as expected, but this is far from accurate, leading to
a wrong i2c-client being instantiated for the charger on some boards.
Switch to the new DMI based intel_cht_wc_get_model() helper which is
exported by the MFD driver for the CHT Whiskey Cove PMIC to help PMIC
cell drivers like the i2c-cht-wc code reliably detect which board
they are running on.
And add board_info for the charger ICs as found on the other 2 known
boards with a Whisky Cove PMIC.
This has been tested on all 3 known boards.
Acked-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add i2c compatible for MT8186. Compare to MT8192 i2c controller,
MT8186 doesn't need handshake signal witch apdma.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change of_*() functions to device_*() for firmware agnostic usage.
This allows to have the smbus_alert interrupt without any changes
in the controller drivers using the ACPI table.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
partial support for < MAX_ORDER - 1 granularity for virtio-mem
driver_override for vdpa
sysfs ABI documentation for vdpa
multiqueue config support for mlx5 vdpa
Misc fixes, cleanups.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmHiDHkPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpVT4H/3Veixt3uYPOmuLU2tSx+8X+sFTtik81hyiE
okz5fRJrxxA8SqS76FnmO10FS4hlPOGNk0Z5WVhr0yihwFvPLvpCM/xi2Lmrz9I7
pB0sXOIocEL1xApsxukR9K1Twpb2hfYsflbJYUVlRfhS5G0izKJNZp5I7OPrzd80
vVNNDWKW2iLDlfqsavumI4Kvm4nsFuCHG03jzMtcIa7YTXYV3DORD4ZGFFVUOIQN
t5F74TznwHOeYgJeg7TzjFjfPWmXjLetvx10QX1A1uOvwppWW/QY6My0UafTXNXj
VB3gOwJPf+gxXAXl/4bafq4NzM0xys6cpcPpjvhmU+erY4UuyAU=
=Y1eO
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"virtio,vdpa,qemu_fw_cfg: features, cleanups, and fixes.
- partial support for < MAX_ORDER - 1 granularity for virtio-mem
- driver_override for vdpa
- sysfs ABI documentation for vdpa
- multiqueue config support for mlx5 vdpa
- and misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (42 commits)
vdpa/mlx5: Fix tracking of current number of VQs
vdpa/mlx5: Fix is_index_valid() to refer to features
vdpa: Protect vdpa reset with cf_mutex
vdpa: Avoid taking cf_mutex lock on get status
vdpa/vdpa_sim_net: Report max device capabilities
vdpa: Use BIT_ULL for bit operations
vdpa/vdpa_sim: Configure max supported virtqueues
vdpa/mlx5: Report max device capabilities
vdpa: Support reporting max device capabilities
vdpa/mlx5: Restore cur_num_vqs in case of failure in change_num_qps()
vdpa: Add support for returning device configuration information
vdpa/mlx5: Support configuring max data virtqueue
vdpa/mlx5: Fix config_attr_mask assignment
vdpa: Allow to configure max data virtqueues
vdpa: Read device configuration only if FEATURES_OK
vdpa: Sync calls set/get config/status with cf_mutex
vdpa/mlx5: Distribute RX virtqueues in RQT object
vdpa: Provide interface to read driver features
vdpa: clean up get_config_size ret value handling
virtio_ring: mark ring unused on error
...
This will enable cleanups down the road.
The idea is to disable cbs, then add "flush_queued_cbs" callback
as a parameter, this way drivers can flush any work
queued after callbacks have been disabled.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20211013105226.20225-1-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pull i2c updates from Wolfram Sang:
"Mostly driver updates and refactorization.
The removal of the XLR driver and the i801 refactoring stand out a
little. In the core, we enabled async suspend/resume for I2C
controllers and their clients. No issues were reported during the test
phase in -next. We will see how this goes for mainline"
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (54 commits)
i2c: sh_mobile: remove unneeded semicolon
i2c: riic: Use platform_get_irq() to get the interrupt
i2c: sh_mobile: Use platform_get_irq_optional() to get the interrupt
i2c: bcm2835: Use platform_get_irq() to get the interrupt
i2c: aspeed: Remove unused includes
dt-bindings: i2c: aspeed: Drop stray '#interrupt-cells'
i2c: sh_mobile: update to new DMAENGINE API when terminating
i2c: rcar: update to new DMAENGINE API when terminating
i2c: exynos5: Fix getting the optional clock
i2c: designware-pci: Convert to use dev_err_probe()
i2c: designware-pci: use __maybe_unused for PM functions
i2c: designware-pci: Group MODULE_*() macros
i2c: designware-pci: Add a note about struct dw_scl_sda_cfg usage
i2c: designware-pci: Fix to change data types of hcnt and lcnt parameters
i2c: designware: Do not complete i2c read without RX_FULL interrupt
eeprom: at24: Add support for 24c1025 EEPROM
dt-bindings: at24: add at24c1025
i2c: tegra: use i2c_timings for bus clock freq
dt-bindings: at24: Rework special case compatible handling
i2c: i801: Don't clear status flags twice in interrupt mode
...
Eliminate the following coccicheck warning:
./drivers/i2c/busses/i2c-sh_mobile.c:849:3-4: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- Update ACPICA code in the kernel to the 20211217 upstream release
including the following changes:
* iASL/Disassembler: Additional support for NHLT table (Bob Moore).
* Change a return_ACPI_STATUS (AE_BAD_PARAMETER) (Bob Moore).
* Fix a couple of warnings under MSVC (Bob Moore).
* iASL: Add TDEL table to both compiler/disassembler (Bob Moore).
* iASL/NHLT table: "Specific Data" field support (Bob Moore).
* Use original data_table_region pointer for accesses (Jessica
Clarke).
* Use original pointer for virtual origin tables (Jessica Clarke).
* Macros: Remove ACPI_PHYSADDR_TO_PTR (Jessica Clarke).
* Avoid subobject buffer overflow when validating RSDP signature
(Jessica Clarke).
* iASL: Add suppport for AGDI table (Ilkka Koskinen).
* Hardware: Do not flush CPU cache when entering S4 and S5 (Kirill
A. Shutemov).
* Expand the ACPI_ACCESS_ definitions (Mark Langsdorf).
* Utilities: Avoid deleting the same object twice in a row (Rafael
Wysocki).
* Executer: Fix REFCLASS_REFOF case in acpi_ex_opcode_1A_0T_1R()
(Rafael Wysocki).
* Fix AEST Processor generic resource substructure data field byte
length (Shuuichirou Ishii).
* Fix wrong interpretation of PCC address (Sudeep Holla).
* Add support for PCC Opregion special context data (Sudeep Holla).
- Implement OperationRegion handler for PCC Type 3 subtype (Sudeep
Holla).
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system
PM transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang Li).
- Rework flushing of EC work while suspended to idle and clean up
the handling of events in the ACPI EC driver (Rafael Wysocki).
- Prohibit ec_sys module parameter write_support from being used
when the system is locked down (Hans de Goede).
- Make the ACPI processor thermal driver use cpufreq_cpu_get() to
check for presence of cpufreq policy (Manfred Spraul).
- Avoid unnecessary CPU cache flushing in the ACPI processor idle
driver (Kirill A. Shutemov).
- Replace kernel.h with the necessary inclusions in the ACPI
processor driver (Andy Shevchenko).
- Use swap() instead of open coding it in the ACPI processor idle
driver (Guo Zhengkui).
- Fix the handling of defective LPAT in the ACPI xpower PMIC driver
and clean up some definitions of PMIC data structures (Hans de
Goede).
- Fix outdated comment in the ACPI DPTF driver (Sumeet Pawnikar).
- Add AEST to the list of known ACPI table signatures (Shuuichirou
Ishii).
- Make ACPI NUMA code take hotpluggable memblocks into account when
CONFIG_MEMORY_HOTPLUG is not set (Vitaly Kuznetsov).
- Use default_groups in kobj_type in the ACPI sysfs code (Greg
Kroah-Hartman).
- Rearrange _CPC structure documentation (Andy Shevchenko).
- Drop an always true check from the ACPI thermal driver (Adam
Borowski).
- Add new "not charging" quirk for Lenovo ThinkPads to the ACPI
battery driver (Thomas Weißschuh).
-----BEGIN PGP SIGNATURE-----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=IGwJ
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These are usual ACPICA code updates (although there are more of them
than in the last few releases), a noticeable EC driver update (which
mostly consists of cleanups, though), the device enumeration quirks
handling rework from Hans, some updates eliminating unnecessary CPU
cache flushing in some places (processor idle and system-wide PM code)
and a bunch of assorted cleanups and fixes.
Specifics:
- Update ACPICA code in the kernel to the 20211217 upstream release
including the following changes:
- iASL/Disassembler: Additional support for NHLT table (Bob
Moore).
- Change a return_ACPI_STATUS (AE_BAD_PARAMETER) (Bob Moore).
- Fix a couple of warnings under MSVC (Bob Moore).
- iASL: Add TDEL table to both compiler/disassembler (Bob Moore).
- iASL/NHLT table: "Specific Data" field support (Bob Moore).
- Use original data_table_region pointer for accesses (Jessica
Clarke).
- Use original pointer for virtual origin tables (Jessica Clarke).
- Macros: Remove ACPI_PHYSADDR_TO_PTR (Jessica Clarke).
- Avoid subobject buffer overflow when validating RSDP signature
(Jessica Clarke).
- iASL: Add suppport for AGDI table (Ilkka Koskinen).
- Hardware: Do not flush CPU cache when entering S4 and S5 (Kirill
A. Shutemov).
- Expand the ACPI_ACCESS_ definitions (Mark Langsdorf).
- Utilities: Avoid deleting the same object twice in a row (Rafael
Wysocki).
- Executer: Fix REFCLASS_REFOF case in acpi_ex_opcode_1A_0T_1R()
(Rafael Wysocki).
- Fix AEST Processor generic resource substructure data field byte
length (Shuuichirou Ishii).
- Fix wrong interpretation of PCC address (Sudeep Holla).
- Add support for PCC Opregion special context data (Sudeep
Holla).
- Implement OperationRegion handler for PCC Type 3 subtype (Sudeep
Holla).
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system PM
transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang
Li).
- Rework flushing of EC work while suspended to idle and clean up the
handling of events in the ACPI EC driver (Rafael Wysocki).
- Prohibit ec_sys module parameter write_support from being used when
the system is locked down (Hans de Goede).
- Make the ACPI processor thermal driver use cpufreq_cpu_get() to
check for presence of cpufreq policy (Manfred Spraul).
- Avoid unnecessary CPU cache flushing in the ACPI processor idle
driver (Kirill A. Shutemov).
- Replace kernel.h with the necessary inclusions in the ACPI
processor driver (Andy Shevchenko).
- Use swap() instead of open coding it in the ACPI processor idle
driver (Guo Zhengkui).
- Fix the handling of defective LPAT in the ACPI xpower PMIC driver
and clean up some definitions of PMIC data structures (Hans de
Goede).
- Fix outdated comment in the ACPI DPTF driver (Sumeet Pawnikar).
- Add AEST to the list of known ACPI table signatures (Shuuichirou
Ishii).
- Make ACPI NUMA code take hotpluggable memblocks into account when
CONFIG_MEMORY_HOTPLUG is not set (Vitaly Kuznetsov).
- Use default_groups in kobj_type in the ACPI sysfs code (Greg
Kroah-Hartman).
- Rearrange _CPC structure documentation (Andy Shevchenko).
- Drop an always true check from the ACPI thermal driver (Adam
Borowski).
- Add new "not charging" quirk for Lenovo ThinkPads to the ACPI
battery driver (Thomas Weißschuh)"
* tag 'acpi-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (64 commits)
ACPI: PCC: Implement OperationRegion handler for the PCC Type 3 subtype
ACPI / x86: Skip AC and battery devices on x86 Android tablets with broken DSDTs
ACPI / x86: Introduce an acpi_quirk_skip_acpi_ac_and_battery() helper
ACPI: processor: thermal: avoid cpufreq_get_policy()
serdev: Do not instantiate serdevs on boards with known bogus DSDT entries
i2c: acpi: Do not instantiate I2C-clients on boards with known bogus DSDT entries
ACPI / x86: Add acpi_quirk_skip_[i2c_client|serdev]_enumeration() helpers
ACPI: scan: Create platform device for BCM4752 and LNV4752 ACPI nodes
PCI/ACPI: Fix acpi_pci_osc_control_set() kernel-doc comment
ACPI: battery: Add the ThinkPad "Not Charging" quirk
ACPI: sysfs: use default_groups in kobj_type
ACPICA: Update version to 20211217
ACPICA: iASL/NHLT table: "Specific Data" field support
ACPICA: iASL: Add suppport for AGDI table
ACPICA: iASL: Add TDEL table to both compiler/disassembler
ACPICA: Fixed a couple of warnings under MSVC
ACPICA: Change a return_ACPI_STATUS (AE_BAD_PARAMETER)
ACPICA: Hardware: Do not flush CPU cache when entering S4 and S5
ACPICA: Add support for PCC Opregion special context data
ACPICA: Fix wrong interpretation of PCC address
...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+QmuaPwR3wnBdVwACF8+vY7k4RUFAmHPqrMACgkQCF8+vY7k
4RUM2g//VzdGU6kq19k7++N7ewGV1VhTnwAXCzdjjMuigdYpTnH/i2fIN/3BS2Mw
RQVTc3Ys26SGdaKCPsMONKjNwQk62hiaQGW4gwnCZ9Me+hgR3e6z67rJa6XWpKuw
aH81Z+XFfyn3Oo8qu7jqCABRCWXfKuxs8Vmc8XdcjvrqlREpiQ0c10oXiboeOoWE
RmVPrnJ94pK8J859dO01cRkDCCo2G9AL9vnBHVA5050VEskSb20+8EmJQDfmkgsO
Itd6JpCK97QTH5gtF44iO3CDWi5f3x9ODWJkQXJEZRAiKORZkcQUpCOXafQjb2vN
YgxO86F/sD7XlhZ3V5AjvztZuQPTmnLNcgnrIVUa7iCAWDft1xBIsjQ+BxV9uROe
g3/Yl6J+Y2Qi+wfAVhCJ94pfA2ZCIoN/+loVi9TQ22X4+tbr6+K4qWu3y1eu9bTW
TYVD//nUMZz/ljFBAgj4OM6RhtMCqI6c2IB3weOEey5wcR641M0mVHPmzgNo5VMQ
mFYkRXwrHrbsWWXxRB9yEJKK6P0MsDWAvoD8QBFvaOmqEBr7gG4ET44G76lcFoyD
Tks4+MZQFQvzas/Xd/GndFlD/T4Cyn+CoPLP1SaP3R01mldoSA39o/cVZlHbZgjI
8zFnPCAsE2C/w+Oko/vGLQZyyetJ8PzohPmlMy8XPaejYulHQqA=
=cCwW
-----END PGP SIGNATURE-----
Merge tag 'media/v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New sensor driver: ov5693
- A new driver for STM32 Chrom-ART Accelerator
- Added V4L2 core helper functions for VP9 codec
- Hantro driver has gained support for VP9 codecs
- Added support for Maxim MAX96712 Quad GMSL2 Deserializer
- The staging atomisp driver has gained lots of improvements, fixes and
cleanups. It now works with userptr
- Lots of random driver improvements as usual
* tag 'media/v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (397 commits)
media: ipu3-cio2: Add support for instantiating i2c-clients for VCMs
media: ipu3-cio2: Call cio2_bridge_init() before anything else
media: ipu3-cio2: Defer probing until the PMIC is fully setup
media: hantro: Add support for Allwinner H6
media: dt-bindings: allwinner: document H6 Hantro G2 binding
media: hantro: Convert imx8m_vpu_g2_irq to helper
media: hantro: move postproc enablement for old cores
media: hantro: vp9: add support for legacy register set
media: hantro: vp9: use double buffering if needed
media: hantro: add support for reset lines
media: hantro: Fix probe func error path
media: i2c: hi846: use pm_runtime_force_suspend/resume for system suspend
media: i2c: hi846: check return value of regulator_bulk_disable()
media: hi556: Support device probe in non-zero ACPI D state
media: ov5675: Support device probe in non-zero ACPI D state
media: imx208: Support device probe in non-zero ACPI D state
media: ov2740: support device probe in non-zero ACPI D state
media: ov5670: Support device probe in non-zero ACPI D state
media: ov8856: support device probe in non-zero ACPI D state
media: ov8865: Disable only enabled regulators on error path
...
These are all minor bug fixes and cleanups to code in arch/arm and
arch/arm64 that is specific to one SoC, updating Kconfig symbols,
the MAINTAINERS file, and removing some dead code.
-----BEGIN PGP SIGNATURE-----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=8wnp
-----END PGP SIGNATURE-----
Merge tag 'soc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"These are all minor bug fixes and cleanups to code in arch/arm and
arch/arm64 that is specific to one SoC, updating Kconfig symbols, the
MAINTAINERS file, and removing some dead code"
* tag 'soc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: exynos: Enable Exynos Multi-Core Timer driver
ARM: ixp4xx: remove unused header file pata_ixp4xx_cf.h
ARM: ixp4xx: remove dead configs CPU_IXP43X and CPU_IXP46X
MAINTAINERS: Add Florian as BCM5301X and BCM53573 maintainer
ARM: samsung: Remove HAVE_S3C2410_I2C and use direct dependencies
ARM: imx: rename DEBUG_IMX21_IMX27_UART to DEBUG_IMX27_UART
ARM: imx: remove dead left-over from i.MX{27,31,35} removal
ARM: s3c: add one more "fallthrough" statement in Jive
ARM: s3c: include header for prototype of s3c2410_modify_misccr
ARM: shmobile: rcar-gen2: Add missing of_node_put()
Merge ACPI device enumeration updates, ACPI power management updates
and PCI host bridge ACPI driver updates for 5.17-rc1:
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system
PM transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang Li).
* acpi-scan:
serdev: Do not instantiate serdevs on boards with known bogus DSDT entries
i2c: acpi: Do not instantiate I2C-clients on boards with known bogus DSDT entries
ACPI / x86: Add acpi_quirk_skip_[i2c_client|serdev]_enumeration() helpers
ACPI: scan: Create platform device for BCM4752 and LNV4752 ACPI nodes
ACPI: Use acpi_fetch_acpi_dev() instead of acpi_bus_get_device()
ACPI: scan: Introduce acpi_fetch_acpi_dev()
ACPI: scan: Do not add device IDs from _CID if _HID is not valid
* acpi-pm:
ACPI: PM: Remove redundant cache flushing
ACPI: PM: Avoid CPU cache flush when entering S4
* acpi-power:
ACPI: PM: Emit debug messages when enabling/disabling wakeup power
* acpi-pci:
PCI/ACPI: Fix acpi_pci_osc_control_set() kernel-doc comment
This largely reverts commit 5a7b95fb99. It
breaks suspend with AMD GPUs, and we couldn't incrementally fix it. So,
let's remove the code and go back to the drawing board. We keep the
header extension to not break drivers already populating the regulator.
We expect to re-add the code handling it soon.
Fixes: 5a7b95fb99 ("i2c: core: support bus regulator controlling in adapter")
Reported-by: "Tareque Md.Hanif" <tarequemd.hanif@yahoo.com>
Link: https://lore.kernel.org/r/1295184560.182511.1639075777725@mail.yahoo.com
Reported-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Link: https://lore.kernel.org/r/7143a7147978f4104171072d9f5225d2ce355ec1.camel@yandex.ru
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1850
Tested-by: "Tareque Md.Hanif" <tarequemd.hanif@yahoo.com>
Tested-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: <stable@vger.kernel.org> # 5.14+
When performing an I2C transfer where the last message was a write KASAN
would complain:
BUG: KASAN: slab-out-of-bounds in mpc_i2c_do_action+0x154/0x630
Read of size 2 at addr c814e310 by task swapper/2/0
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G B 5.16.0-rc8 #1
Call Trace:
[e5ee9d50] [c08418e8] dump_stack_lvl+0x4c/0x6c (unreliable)
[e5ee9d70] [c02f8a14] print_address_description.constprop.13+0x64/0x3b0
[e5ee9da0] [c02f9030] kasan_report+0x1f0/0x204
[e5ee9de0] [c0c76ee4] mpc_i2c_do_action+0x154/0x630
[e5ee9e30] [c0c782c4] mpc_i2c_isr+0x164/0x240
[e5ee9e60] [c00f3a04] __handle_irq_event_percpu+0xf4/0x3b0
[e5ee9ec0] [c00f3d40] handle_irq_event_percpu+0x80/0x110
[e5ee9f40] [c00f3e48] handle_irq_event+0x78/0xd0
[e5ee9f60] [c00fcfec] handle_fasteoi_irq+0x19c/0x370
[e5ee9fa0] [c00f1d84] generic_handle_irq+0x54/0x80
[e5ee9fc0] [c0006b54] __do_irq+0x64/0x200
[e5ee9ff0] [c0007958] __do_IRQ+0xe8/0x1c0
[c812dd50] [e3eaab20] 0xe3eaab20
[c812dd90] [c0007a4c] do_IRQ+0x1c/0x30
[c812dda0] [c0000c04] ExternalInput+0x144/0x160
--- interrupt: 500 at arch_cpu_idle+0x34/0x60
NIP: c000b684 LR: c000b684 CTR: c0019688
REGS: c812ddb0 TRAP: 0500 Tainted: G B (5.16.0-rc8)
MSR: 00029002 <CE,EE,ME> CR: 22000488 XER: 20000000
GPR00: c10ef7fc c812de90 c80ff200 c2394718 00000001 00000001 c10e3f90 00000003
GPR08: 00000000 c0019688 c2394718 fc7d625b 22000484 00000000 21e17000 c208228c
GPR16: e3e99284 00000000 ffffffff c2390000 c001bac0 c2082288 c812df60 c001ba60
GPR24: c23949c0 00000018 00080000 00000004 c80ff200 00000002 c2348ee4 c2394718
NIP [c000b684] arch_cpu_idle+0x34/0x60
LR [c000b684] arch_cpu_idle+0x34/0x60
--- interrupt: 500
[c812de90] [c10e3f90] rcu_eqs_enter.isra.60+0xc0/0x110 (unreliable)
[c812deb0] [c10ef7fc] default_idle_call+0xbc/0x230
[c812dee0] [c00af0e8] do_idle+0x1c8/0x200
[c812df10] [c00af3c0] cpu_startup_entry+0x20/0x30
[c812df20] [c001e010] start_secondary+0x5d0/0xba0
[c812dff0] [c00028a0] __secondary_start+0x90/0xdc
This happened because we would overrun the i2c->msgs array on the final
interrupt for the I2C STOP. This didn't happen if the last message was a
read because there is no interrupt in that case. Ensure that we only
access the current message if we are not processing a I2C STOP
condition.
Fixes: 1538d82f46 ("i2c: mpc: Interrupt driven transfer")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional() for DT users only.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Wrong user data may cause warning in i2c_transfer(), ex: zero msgs.
Userspace should not be able to trigger warnings, so this patch adds
validation checks for user data in compact ioctl to prevent reported
warnings
Reported-and-tested-by: syzbot+e417648b303855b91d8a@syzkaller.appspotmail.com
Fixes: 7d5cb45655 ("i2c compat ioctls: move to ->compat_ioctl()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
x86 ACPI devices which ship with only Android as their factory image
usually declare a whole bunch of bogus I2C devices in their ACPI tables.
Instantiating I2C clients for these bogus devices causes various issues,
e.g. GPIO/IRQ resource conflicts because sometimes drivers do bind to them.
The Android x86 kernel fork shipped on these devices has some special code
to remove these bogus devices, instead of just fixing the DSDT <sigh>.
Use the new acpi_quirk_skip_i2c_client_enumeration() helper to identify
known boards / acpi devices with this issue, and skip enumerating these.
Note these boards typically do actually have I2C devices, just
different ones then the ones described in their DSDT. The devices
which are actually present are manually instantiated by the
drivers/platform/x86/x86-android-tablets.c kernel module.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No symbols from the linux/irqchip/chained_irq.h and linux/irqdomain.h
headers are used in the driver, so they can be removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated. When converting the existing
calls, it turned out that the termination in the DMA setup and callback
were superfluous and only a side effect of simply calling
rcar_i2c_cleanup_dma(). As either no DMA transfers have been submitted
yet or the last one has successfully completed, there is nothing to
terminate and we can leave it out. So, merge the DMA unmap and cleanup
function to save some code. Then, add a flag if the new cleanup function
needs to terminate DMA. This is only the case for the erorr handling in
the main thread, so we can finally switch from dmaengine_terminate_all()
to dmaengine_terminate_sync() here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated. When converting the existing
calls, it turned out that the termination in the interrupt handlers was
superfluous and only a side effect of simply calling
rcar_i2c_cleanup_dma(). As either no DMA transfers have been submitted
yet or the last one has successfully completed, there is nothing to
terminate and we can leave it out. So, merge the DMA unmap and cleanup
function to save some code. Then, add a flag if the new cleanup function
needs to terminate DMA. This is only the case for the erorr handling in
the main thread, so we can finally switch from dmaengine_terminate_all()
to dmaengine_terminate_sync() here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
"hsi2c_pclk" clock is optional and may not be present for some SoCs
supported by this driver. Nevertheless, in case the clock is provided
but some error happens during its getting, that error should be handled
properly. Use devm_clk_get_optional() API for that. Also report possible
errors using dev_err_probe() to handle properly -EPROBE_DEFER error (if
clock provider is not ready by the time I2C probe function is executed).
Fixes: 697ad2490c ("i2c: exynos5: Add bus clock support")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
[wsa: fixed SHA1 of Fixes tag]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It's fine to call dev_err_probe() in ->probe() when error code is known.
Convert the driver to use dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use __maybe_unused for PM functions instead of ifdeffery.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
For better maintenance group MODULE_*() macros together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add a note about struct dw_scl_sda_cfg usage to discourage people
of using this structure on new platforms. Instead they should try
hard to put the needed information into firmware descriptions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The data type of hcnt and lcnt in the struct dw_i2c_dev is of type u16.
It's better to have same data type in struct dw_scl_sda_cfg as well.
Reported-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Intel Keem Bay platform supports multi-master operations over same i2c
bus using Synopsys i2c DesignWare IP. When multi-masters initiate i2c
operation simultaneously in a loop, SCL line is stucked low forever
after few i2c operations. Following interrupt sequences are observed
in:
working case: TX_EMPTY, RX_FULL and STOP_DET
non working case: TX_EMPTY, STOP_DET, RX_FULL.
DW_apb_i2c stretches the SCL line when the TX FIFO is empty or when
RX FIFO is full. The DW_apb_i2c master will continue to hold the SCL
line LOW until RX FIFO is read.
Linux kernel i2c DesignWare driver does not handle above non working
sequence. TX_EMPTY, RX_FULL and STOP_DET routine execution are required
in sequence although RX_FULL interrupt is raised after STOP_DET by
hardware. Clear STOP_DET for the following conditions:
(STOP_DET ,RX_FULL, rx_outstanding)
Write Operation: (1, 0, 0)
Read Operation:
RX_FULL followed by STOP_DET: (0, 1, 1) -> (1, 0, 0)
STOP_DET followed by RX_FULL: (1, 0, 1) -> (1, 1, 0)
RX_FULL and STOP_DET together: (1, 1, 1)
Signed-off-by: Tamal Saha <tamal.saha@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This branch contains 5.16-rc1 + the pending ACPI/i2c, tps68570 platform_data
and INT3472 driver patches.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmG6YLQUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9zwGwf8Csb4wXyc3duBlnX/9jO9REDVKTN9
HhmU2KQm29g10dN2nlFXEOG16xAy8zt3BE7QwniL/R5sUsKTCAEugY8Aqq/4+lFA
vTU+YR9YqZFmEDGMfDngHeh9ZvSWIJS7IEXthxCkgGVhrd2Wl50jKTjVyq1RIDKv
a7B4fOhguFv95xRlnXK+yoVUU7zZPWAgxyCqV0E0JEi8aWE8Y483IRCzcDEyJeDa
HkgZLVwD9l3WQ4uZllVg1q5jfSprHwBa8dFxgcd6mOOYaKowiJ+GjnvnXOto5X72
zsODBJH15VzfVXF5cAqIvzN6nAFR8Mxieei+21iFyUD/Ps1vfWlodFHH2w==
=Q1N9
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-int3472-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86 into media_tree
Signed tag for the immutable platform-drivers-x86-int3472 branch
This branch contains 5.16-rc1 + the pending ACPI/i2c, tps68570 platform_data
and INT3472 driver patches.
* tag 'platform-drivers-x86-int3472-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: int3472: Deal with probe ordering issues
platform/x86: int3472: Pass tps68470_regulator_platform_data to the tps68470-regulator MFD-cell
platform/x86: int3472: Pass tps68470_clk_platform_data to the tps68470-regulator MFD-cell
platform/x86: int3472: Add get_sensor_adev_and_name() helper
platform/x86: int3472: Split into 2 drivers
platform_data: Add linux/platform_data/tps68470.h file
i2c: acpi: Add i2c_acpi_new_device_by_fwnode() function
i2c: acpi: Use acpi_dev_ready_for_enumeration() helper
ACPI: delay enumeration of devices with a _DEP pointing to an INT3472 device
Change i2c_acpi_new_device() into i2c_acpi_new_device_by_fwnode() and
add a static inline wrapper providing the old i2c_acpi_new_device()
behavior.
This is necessary because in some cases we may only have access
to the fwnode / acpi_device and not to the matching physical-node
struct device *.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-4-hdegoede@redhat.com
The clk and regulator frameworks expect clk/regulator consumer-devices
to have info about the consumed clks/regulators described in the device's
fw_node.
To work around cases where this info is not present in the firmware tables,
which is often the case on x86/ACPI devices, both frameworks allow the
provider-driver to attach info about consumers to the clks/regulators
when registering these.
This causes problems with the probe ordering wrt drivers for consumers
of these clks/regulators. Since the lookups are only registered when the
provider-driver binds, trying to get these clks/regulators before then
results in a -ENOENT error for clks and a dummy regulator for regulators.
To ensure the correct probe-ordering the ACPI core has code to defer the
enumeration of consumers affected by this until the providers are ready.
Call the new acpi_dev_ready_for_enumeration() helper to avoid
enumerating / instantiating i2c-clients too early.
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-3-hdegoede@redhat.com
Maxime points out that the polling code in mpc_i2c_isr should use the
_atomic API because it is called in an irq context and that the
behaviour of the MCF bit is that it is 1 when the byte transfer is
complete. All of this means the original code was effectively a
udelay(100).
Fix this by using readb_poll_timeout_atomic() and removing the negation
of the break condition.
Fixes: 4a8ac5e45c ("i2c: mpc: Poll for MCF")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use i2c_timings struct and corresponding methods to get bus clock frequency
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In interrupt mode we clear the status flags twice, in the interrupt
handler and in i801_check_post(). Remove clearing the status flags
from i801_check_post() and handle polling mode by using the
SMBus unlocking write to also clear the status flags if still set.
To be precise: One could still argue that the status flags are
cleared twice in interrupt mode, but it comes for free.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I see no need to read back the registers to verify that the bits
have actually been cleared. I can't imagine any scenario where
the bits would remain set after a write to them.
Whilst at it, change involved syslog messages to use pci_dbg() et al.
to simplify them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I2C controller chosen by I2C_EXYNOS5 config option is also suitable for
Exynos850 and ExynosAutoV9 SoCs. State that specifically in I2C_EXYNOS5
symbol help section.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In new Exynos SoCs (like Exynos850) where HSI2C is implemented as a
part of USIv2 block, there are two clocks provided to HSI2C controller:
- PCLK: bus clock (APB), provides access to register interface
- IPCLK: operating IP-core clock; SCL is derived from this one
Both clocks have to be asserted for HSI2C to be functional in that case.
Add code to obtain and enable/disable PCLK in addition to already
handled operating clock. Make it optional though, as older Exynos SoC
variants only have one HSI2C clock.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
ExynosAutoV9 functioning logic mostly follows I2C_TYPE_EXYNOS7, but
timing calculation and configuration procedure is changed: e.g. only
timing_s3 has to be set now.
Another change of HSI2C controller in ExynosAutoV9 SoC is that it's now
a part of USIv2 IP-core. No changes is needed for I2C driver though, as
all USI related configuration is done in USI driver.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver currently assumes that the notify callback is only received
when the device is done with all the queued buffers.
However, this is not true, since the notify callback could be called
without any of the queued buffers being completed (for example, with
virtio-pci and shared interrupts) or with only some of the buffers being
completed (since the driver makes them available to the device in
multiple separate virtqueue_add_sgs() calls).
This can lead to incorrect data on the I2C bus or memory corruption in
the guest if the device operates on buffers which are have been freed by
the driver. (The WARN_ON in the driver is also triggered.)
BUG kmalloc-128 (Tainted: G W ): Poison overwritten
First byte 0x0 instead of 0x6b
Allocated in i2cdev_ioctl_rdwr+0x9d/0x1de age=243 cpu=0 pid=28
memdup_user+0x2e/0xbd
i2cdev_ioctl_rdwr+0x9d/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in i2cdev_ioctl_rdwr+0x1bb/0x1de age=68 cpu=0 pid=28
kfree+0x1bd/0x1cc
i2cdev_ioctl_rdwr+0x1bb/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Fix this by calling virtio_get_buf() from the notify handler like other
virtio drivers and by actually waiting for all the buffers to be
completed.
Fixes: 3cfc883804 ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The log messages talk about 'bus recovery' while it is not a bus
recovery with 9 pulses but merely a controller reset. Controller resets
are not worth log messages. The 'bus busy' message should be emitted by
upper layers, a busy bus may be expected in some cases.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Function stm32f7_i2c_release_bus is always returning 0, hence it
should be a void function. Update the function and remove the
return value error checking code in caller functions.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In a typical read transfer, start completion flag is being set after
read finishes (notice ipd bit 4 being set):
trasnfer poll=0
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33
This causes I2C transfer being aborted in polled mode from a stop completion
handler:
trasnfer poll=1
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13
i2c stop
rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10
Clearing the START flag after read fixes the issue without any obvious
side effects.
This issue was dicovered on RK3566 when adding support for powering
off the RK817 PMIC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit e8578547ce. Drivers
should read these values from ACPI tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit 36af188f79. Drivers
should read these values from ACPI tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we use dmaengine_terminate_sync in
i2c_xfer and i2c_smbus_xfer handlers and rely on
dmaengine_terminate_async within interrupt handlers
(transmission error cases).
dmaengine_synchronize is added within i2c_xfer and i2c_smbus_xfer handler
to finalize terminate started in interrupt handlers.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.
Fixes: 7ecc8cfde5 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When getting an access timeout, ensure that the bus is in a proper
state prior to returning the error.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The platform data structures are used in the respective i801_add_tco
functions only. Therefore we can make the definitions local to these
functions.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Set optimal HCNT, LCNT and hold time values for all the speeds supported
in Intel Programmable Service Engine I2C controller in Intel Elkhart
Lake.
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support to configure HCNT, LCNT values for Fast Mode Plus and High
Speed Mode.
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This enables the async suspend for i2c client devices. This reduces
the suspend/resume time considerably on platforms where i2c devices
can take a lot of time (hundreds of ms) to resume.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Rajat Jain <rajatja@google.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Enable async suspend/resume of i2c adapters. It enormously helps with
reducing the resume time of systems (as much as 20%-40%) where I2C devices
can take significant time (100s of ms) to resume.
Signed-off-by: Rajat Jain <rajatja@google.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Mark the designware devices for asynchronous suspend. With this, the
resume for designware devices does not get stuck behind other unrelated
devices (e.g. intel_backlight that takes hundreds of ms to resume,
waiting for its parent devices).
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Current I2C reset procedure is broken in two ways:
1) It only generate 1 START instead of 9 STARTs and STOP.
2) It leaves the bus Busy so every I2C xfer after the first
fixup calls the reset routine again, for every xfer there after.
This fixes both errors.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
While handling an error during transfer (ex: NACK), it could
happen that the driver has already written data into TXDR
before the transfer get stopped.
This commit add TXDR Flush after end of transfer in case of error to
avoid sending a wrong data on any other slave upon next transfer.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
$ scripts/kernel-doc -none drivers/i2c/busses/i2c-designware-core.h
warning: Function parameter or member 'rst' not described in 'dw_i2c_dev'
warning: Function parameter or member 'get_clk_rate_khz' not described in 'dw_i2c_dev'
warning: Function parameter or member 'flags' not described in 'dw_i2c_dev'
warning: Function parameter or member 'functionality' not described in 'dw_i2c_dev'
warning: Function parameter or member 'master_cfg' not described in 'dw_i2c_dev'
warning: Function parameter or member 'set_sda_hold_time' not described in 'dw_i2c_dev'
warning: Function parameter or member 'rinfo' not described in 'dw_i2c_dev'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Randy Dunlap <rdunla@infradead.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
clk_get_rate() is documented as requiring the clock to be enabled.
Ensure that the bus clock is enabled before calling clk_get_rate() in
rk3x_i2c_probe() to satisfy this requirement.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reduce source code and code size by defining the chip features
statically.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If FEATURE_BLOCK_BUFFER is set then bit SMBAUXCTL_E32B is supported
and there's no benefit in reading it back. Origin of this check
seems to be 14 yrs ago when people were not completely sure which
chip versions support the block buffer mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If an invalid block size is provided, reject it instead of silently
changing it to a supported value. Especially critical I see the case of
a write transfer with block length 0. In this case we have no guarantee
that the byte we would write is valid. When silently reducing a read to
32 bytes then we don't return an error and the caller may falsely
assume that we returned the full requested data.
If this change should break any (broken) caller, then I think we should
fix the caller.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
CBUS transfers have always been atomic, but after commit 63b96983a5
("i2c: core: introduce callbacks for atomic transfers") we started to see
warnings during e.g. poweroff as the atomic callback is not explicitly set.
Fix that.
Fixes the following WARNING seen during Nokia N810 power down:
[ 786.570617] reboot: Power down
[ 786.573913] ------------[ cut here ]------------
[ 786.578826] WARNING: CPU: 0 PID: 672 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x110
[ 786.587799] No atomic I2C transfer handler for 'i2c-2'
Fixes: 63b96983a5 ("i2c: core: introduce callbacks for atomic transfers")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for the ACPI based device registration so that the driver
can be also enabled through ACPI table.
This does not include the ACPI support for Tegra VI and DVC I2C.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use array_size() helper to aid in 2-factor allocation instances.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We have a special helper to get fwnode out of struct device.
Moreover, dereferencing it directly prevents the fwnode
modifications in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Recently ACPI gained the acpi_get_local_address() API which may be used
instead of home grown i2c_mux_gpio_get_acpi_adr().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Most IMX I2C interfaces don't generate an interrupt on a stop condition,
so it won't generate a timely stop event on a slave mode transfer.
Some users, like IPMB, need a timely stop event to work properly.
So, add a timer and add the proper handling to generate a stop event in
slave mode if the interface goes idle.
Signed-off-by: Corey Minyard <minyard@acm.org>
Tested-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If a timeout is hit, it can result is incorrect data on the I2C bus
and/or memory corruptions in the guest since the device can still be
operating on the buffers it was given while the guest has freed them.
Here is, for example, the start of a slub_debug splat which was
triggered on the next transfer after one transfer was forced to timeout
by setting a breakpoint in the backend (rust-vmm/vhost-device):
BUG kmalloc-1k (Not tainted): Poison overwritten
First byte 0x1 instead of 0x6b
Allocated in virtio_i2c_xfer+0x65/0x35c age=350 cpu=0 pid=29
__kmalloc+0xc2/0x1c9
virtio_i2c_xfer+0x65/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in virtio_i2c_xfer+0x32e/0x35c age=244 cpu=0 pid=29
kfree+0x1bd/0x1cc
virtio_i2c_xfer+0x32e/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
There is no simple fix for this (the driver would have to always create
bounce buffers and hold on to them until the device eventually returns
the buffers), so just disable the timeout support for now.
Fixes: 3cfc883804 ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Jie Deng <jie.deng@intel.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently interrupt storm will occur from i2c-i801 after first
transaction if SMB_ALERT signal is enabled and ever asserted. It is
enough if the signal is asserted once even before the driver is loaded
and does not recover because that interrupt is not acknowledged.
This fix aims to fix it by two ways:
- Add acknowledging for the SMB_ALERT interrupt status
- Disable the SMB_ALERT interrupt on platforms where possible since the
driver currently does not make use for it
Acknowledging resets the SMB_ALERT interrupt status on all platforms and
also should help to avoid interrupt storm on older platforms where the
SMB_ALERT interrupt disabling is not available.
For simplicity this fix reuses the host notify feature for disabling and
restoring original register value.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177311
Reported-by: ck+kernelbugzilla@bl4ckb0x.de
Reported-by: stephane.poignant@protonmail.com
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If driver interrupts are enabled, SMBHSTCNT_INTREN will be 1 after
the first transaction, and will stay to that value forever. This
means that interrupts will be generated for both host-initiated
transactions and also SMBus Alert events even after the driver is
unloaded. To be on the safe side, we should restore the initial state
of this bit at suspend and reboot time, as we do for several other
configuration bits already and for the same reason: the BIOS should
be handed the device in the same configuration state in which we
received it. Otherwise interrupts may be generated which nobody
will process.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commits 95b8a5e011 ("MIPS: Remove NETLOGIC support") and edd4488aea
("ARM: remove tango platform") removed Netlogic XLR and Sigma Designs
Tango platforms which means there are no platforms using the XLR I2C
driver and it can be removed.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Netlogic XLP was removed in commit 95b8a5e011 ("MIPS: Remove NETLOGIC
support"). With those gone, the single platform left to support is
Cavium ThunderX2. Remove the Netlogic variant and DT support.
For simplicity, the existing kconfig name is retained.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by George Cherian <gcherian@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A separate Kconfig option HAVE_S3C2410_I2C for Samsung SoCs is not
really needed and the i2c-s3c24xx driver can depend on Samsung ARM
architectures instead. This also enables i2c-s3c2410 for arm64 Exynos
SoCs, which is required for example by Exynos850.
This is basically continuation of work made in following commits:
- commit d96890fca9 ("rtc: s3c: remove HAVE_S3C_RTC in favor of
direct dependencies")
- commit 7dd3cae90d ("ARM: samsung: remove HAVE_S3C2410_WATCHDOG and
use direct dependencies")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211121150558.21801-2-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
- Add support for new ACPI device configuration object called _DSC
to allow certain devices to be probed without changing their power
states, document it and make two drivers use it (Sakari Ailus,
Rajmohan Mani).
- Fix device wakeup power reference counting broken recently by
mistake (Rafael Wysocki).
- Drop unused symbol and macros depending on it from acgcc.h (Rafael
Wysocki).
- Add HP ZHAN 66 Pro to the "no EC wakeup" quirk list (Binbin Zhou).
- Add Xiaomi Mi Pad 2 to the backlight quirk list and drop an unused
piece of data from all of the list entries (Hans de Goede).
- Fix register read accesses handling in the Intel PMIC operation
region driver (Hans de Goede).
- Clean up static variables initialization in the EC driver
(wangzhitong).
-----BEGIN PGP SIGNATURE-----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=k8+T
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These add support for a new ACPI device configuration object called
_DSC, fix some issues including one recent regression, add two new
items to quirk lists and clean up assorted pieces of code.
Specifics:
- Add support for new ACPI device configuration object called _DSC
("Deepest State for Configuration") to allow certain devices to be
probed without changing their power states, document it and make
two drivers use it (Sakari Ailus, Rajmohan Mani).
- Fix device wakeup power reference counting broken recently by
mistake (Rafael Wysocki).
- Drop unused symbol and macros depending on it from acgcc.h (Rafael
Wysocki).
- Add HP ZHAN 66 Pro to the "no EC wakeup" quirk list (Binbin Zhou).
- Add Xiaomi Mi Pad 2 to the backlight quirk list and drop an unused
piece of data from all of the list entries (Hans de Goede).
- Fix register read accesses handling in the Intel PMIC operation
region driver (Hans de Goede).
- Clean up static variables initialization in the EC driver
(wangzhitong)"
* tag 'acpi-5.16-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Documentation: ACPI: Fix non-D0 probe _DSC object example
ACPI: Drop ACPI_USE_BUILTIN_STDARG ifdef from acgcc.h
ACPI: PM: Fix device wakeup power reference counting error
ACPI: video: use platform backlight driver on Xiaomi Mi Pad 2
ACPI: video: Drop dmi_system_id.ident settings from video_detect_dmi_table[]
ACPI: PMIC: Fix intel_pmic_regs_handler() read accesses
ACPI: EC: Remove initialization of static variables to false
ACPI: EC: Use ec_no_wakeup on HP ZHAN 66 Pro
at24: Support probing while in non-zero ACPI D state
media: i2c: imx319: Support device probe in non-zero ACPI D state
ACPI: Add a convenience function to tell a device is in D0 state
Documentation: ACPI: Document _DSC object usage for enum power state
i2c: Allow an ACPI driver to manage the device's power state during probe
ACPI: scan: Obtain device's desired enumeration power state
Pull i2c updates from Wolfram Sang:
- big refactoring of the PASEMI driver to support the Apple M1
- huge improvements to the XIIC in terms of locking and SMP safety
- refactoring and clean ups for the i801 driver
... and the usual bunch of small driver updates
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (43 commits)
i2c: amd-mp2-plat: ACPI: Use ACPI_COMPANION() directly
i2c: i801: Add support for Intel Ice Lake PCH-N
i2c: virtio: update the maintainer to Conghui
i2c: xlr: Fix a resource leak in the error handling path of 'xlr_i2c_probe()'
i2c: qup: move to use request_irq by IRQF_NO_AUTOEN flag
i2c: qup: fix a trivial typo
i2c: tegra: Ensure that device is suspended before driver is removed
i2c: i801: Fix incorrect and needless software PEC disabling
i2c: mediatek: Dump i2c/dma register when a timeout occurs
i2c: mediatek: Reset the handshake signal between i2c and dma
i2c: mlxcpld: Allow flexible polling time setting for I2C transactions
i2c: pasemi: Set enable bit for Apple variant
i2c: pasemi: Add Apple platform driver
i2c: pasemi: Refactor _probe to use devm_*
i2c: pasemi: Allow to configure bus frequency
i2c: pasemi: Move common reset code to own function
i2c: pasemi: Split pci driver to its own file
i2c: pasemi: Split off common probing code
i2c: pasemi: Remove usage of pci_dev
i2c: pasemi: Use dev_name instead of port number
...
The ACPI_HANDLE() macro is a wrapper arond the ACPI_COMPANION()
macro and the ACPI handle produced by the former comes from the
ACPI device object produced by the latter, so it is way more
straightforward to evaluate the latter directly instead of passing
the handle produced by the former to acpi_bus_get_device().
Modify i2c_amd_probe() accordingly (no intentional functional impact).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add PCI ID of SMBus controller on Intel Ice Lake PCH-N.
The device can be found on MacBookPro16,2 [1].
[1]: https://linux-hardware.org/?probe=f1c5cf0c43
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
PTR_ERR should access the value just tested by IS_ERR, otherwise
the wrong error code will be returned.
Fixes: 7b6da7fe7b ("mailbox: pcc: Use PCC mailbox channel pointer instead of standard")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Here is the big set of driver core changes for 5.16-rc1.
All of these have been in linux-next for a while now with no reported
problems.
Included in here are:
- big update and cleanup of the sysfs abi documentation files
and scripts from Mauro. We are almost at the place where we
can properly check that the running kernel's sysfs abi is
documented fully.
- firmware loader updates
- dyndbg updates
- kernfs cleanups and fixes from Christoph
- device property updates
- component fix
- other minor driver core cleanups and fixes
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYYPbjQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ync9gCfXKMUI1GAnCfJWAwTdTcd18q5akoAoMw32/AH
0yh5TjAWFyFd7xz5d7qs
=itsC
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 5.16-rc1.
All of these have been in linux-next for a while now with no reported
problems.
Included in here are:
- big update and cleanup of the sysfs abi documentation files and
scripts from Mauro. We are almost at the place where we can
properly check that the running kernel's sysfs abi is documented
fully.
- firmware loader updates
- dyndbg updates
- kernfs cleanups and fixes from Christoph
- device property updates
- component fix
- other minor driver core cleanups and fixes"
* tag 'driver-core-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (122 commits)
device property: Drop redundant NULL checks
x86/build: Tuck away built-in firmware under FW_LOADER
vmlinux.lds.h: wrap built-in firmware support under FW_LOADER
firmware_loader: move struct builtin_fw to the only place used
x86/microcode: Use the firmware_loader built-in API
firmware_loader: remove old DECLARE_BUILTIN_FIRMWARE()
firmware_loader: formalize built-in firmware API
component: do not leave master devres group open after bind
dyndbg: refine verbosity 1-4 summary-detail
gpiolib: acpi: Replace custom code with device_match_acpi_handle()
i2c: acpi: Replace custom function with device_match_acpi_handle()
driver core: Provide device_match_acpi_handle() helper
dyndbg: fix spurious vNpr_info change
dyndbg: no vpr-info on empty queries
dyndbg: vpr-info on remove-module complete, not starting
device property: Add missed header in fwnode.h
Documentation: dyndbg: Improve cli param examples
dyndbg: Remove support for ddebug_query param
dyndbg: make dyndbg a known cli param
dyndbg: show module in vpr-info in dd-exec-queries
...
Hardening work by Jason
vdpa driver for Alibaba ENI
Performance tweaks for virtio blk
virtio rng rework using an internal buffer
mac/mtu programming for mlx5 vdpa
Misc fixes, cleanups
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmF/su8PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpo+sIAJjBTvbET+d0KuIMt8YBGsU+NWgHaJxW06hm
GHZzinueZYWaS20MPMYMPfcHUgigWj0kk7F0gMljG5rtDFzR85JkOi7+e5V6RVJW
8SQc7JjA1Krde6EiPJdlv3mVkLz/5VbrGUgjAW9di/O04Xc/jAc9kmJ41wTYr0mL
E5IsUi9QBmgHtKQ+2ofb9QEWuebJclGK+NVd3Kp08BtAQOrdn5UrIzY30/sjkZwE
ul2ll6v/k7T3dCQbHD/wMgfFycPvoZVfxaVj+FWQnwdWkqZwzMRmpKPRes4KJfww
Lfx1qox10mJzH7XJCs7xmOM8f7HgNNWi0gD5FxNlfkiz1AwHYOk=
=DTXY
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"vhost and virtio fixes and features:
- Hardening work by Jason
- vdpa driver for Alibaba ENI
- Performance tweaks for virtio blk
- virtio rng rework using an internal buffer
- mac/mtu programming for mlx5 vdpa
- Misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (45 commits)
vdpa/mlx5: Forward only packets with allowed MAC address
vdpa/mlx5: Support configuration of MAC
vdpa/mlx5: Fix clearing of VIRTIO_NET_F_MAC feature bit
vdpa_sim_net: Enable user to set mac address and mtu
vdpa: Enable user to set mac and mtu of vdpa device
vdpa: Use kernel coding style for structure comments
vdpa: Introduce query of device config layout
vdpa: Introduce and use vdpa device get, set config helpers
virtio-scsi: don't let virtio core to validate used buffer length
virtio-blk: don't let virtio core to validate used length
virtio-net: don't let virtio core to validate used length
virtio_ring: validate used buffer length
virtio_blk: correct types for status handling
virtio_blk: allow 0 as num_request_queues
i2c: virtio: Add support for zero-length requests
virtio-blk: fixup coccinelle warnings
virtio_ring: fix typos in vring_desc_extra
virtio-pci: harden INTX interrupts
virtio_pci: harden MSI-X interrupts
virtio_config: introduce a new .enable_cbs method
...
Enable drivers to tell ACPI that there's no need to power on a device for
probe. Drivers should still perform this by themselves if there's a need
to. In some cases powering on the device during probe is undesirable, and
this change enables a driver to choose what fits best for it.
Add a field called "flags" into struct i2c_driver for driver flags, and a
flag I2C_DRV_ACPI_WAIVE_D0_PROBE to tell a driver supports probe in ACPI D
states other than 0.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The virtio specification received a new mandatory feature
(VIRTIO_I2C_F_ZERO_LENGTH_REQUEST) for zero length requests. Fail if the
feature isn't offered by the device.
For each read-request, set the VIRTIO_I2C_FLAGS_M_RD flag, as required
by the VIRTIO_I2C_F_ZERO_LENGTH_REQUEST feature.
This allows us to support zero length requests, like SMBUS Quick, where
the buffer need not be sent anymore.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/7c58868cd26d2fc4bd82d0d8b0dfb55636380110.1634808714.git.viresh.kumar@linaro.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jie Deng <jie.deng@intel.com> # once the spec is merged
Now that we have all the shared memory region information populated in
the pcc_mbox_chan, let us propagate the pointer to the same as the
return value to pcc_mbox_request channel.
This eliminates the need for the individual users of PCC mailbox to
parse the PCCT subspace entries and fetch the shmem information. This
also eliminates the need for PCC mailbox controller to set con_priv to
PCCT subspace entries. This is required as con_priv is private to the
controller driver to attach private data associated with the channel and
not meant to be used by the mailbox client/users.
Let us convert all the users of pcc_mbox_{request,free}_channel to use
new interface.
Cc: Jean Delvare <jdelvare@suse.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
More specifically, 'clk_prepare_enable()' is used, but 'clk_disable()' is
also already called. So just the unprepare step has still to be done.
Update the error handling path accordingly.
Fixes: 75d31c2372 ("i2c: xlr: add support for Sigma Designs controller variant")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable because of requesting.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Correct the typo of "reamining" to "remaining".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Tegra I2C device isn't guaranteed to be suspended after removal of
the driver since driver uses pm_runtime_put() that is asynchronous and
pm_runtime_disable() cancels pending power-change requests. This means
that potentially refcount of the clocks may become unbalanced after
removal of the driver. This a very minor problem which unlikely to
happen in practice and won't cause any visible problems, nevertheless
let's replace pm_runtime_disable() with pm_runtime_force_suspend() and
use pm_runtime_put_sync() which disables RPM of the device and puts it
into suspend before driver is removed.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit a6b8bb6a81 ("i2c: i801: Fix handling SMBHSTCNT_PEC_EN")
attempts to disable software PEC by clearing the SMBHSTCNT_PEC_EN (bit 7)
in the SMBus Host Control register (I/O SMBHSTCNT) but incorrectly
clears it in the PCI Host Configuration register (PCI SMBHSTCFG).
This clearing is actually needless since after above commit the
SMBHSTCNT_PEC_EN is never set and the register is initialized with known
values.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since driver core provides a generic device_match_acpi_handle()
we may replace the custom one with it. This unifies code to find
an adapter with the similar one which finds a client.
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20211014134756.39092-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a timeout error occurs in i2c transter, it is usually related
to the i2c/dma IP hardware configuration. Therefore, the purpose of
this patch is to dump the key register values of i2c/dma when a
timeout occurs in i2c for debugging.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Due to changes in the hardware design of the handshaking signal
between i2c and dma, it is necessary to reset the handshaking
signal before each transfer to ensure that the multi-msgs can
be transferred correctly.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Allow polling time setting according to I2C frequency supported across
the system. For base frequency 400 KHz and 1 MHz set polling time is set
four times less than for system with base frequency 100KHz.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some later revisions after the original PASemi I2C controller introduce
what likely is an enable bit to the CTL register. Without setting it the
actual i2c transmission is never started.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With all the previous preparations we can now finally add
the platform driver to support the PASemi-based controllers
in Apple SoCs. This does not work on the M1 yet but should
work on the early iPhones already.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using managed device resources means there's nothing left to be done in
pasemi_smb_pci_remove and also allows to remove base and size from
struct pasemi_smbus.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Right now the bus frequency has always been hardcoded as
100 KHz with the specific reference clock used in the PASemi
PCI controllers. Make this configurable to prepare for the
platform driver.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Split out common reset call to its own function so that we
can later add support for selecting the clock frequency
and an additional enable bit found in newer revisions.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Split off the PCI driver so that we can reuse common code for the
platform driver.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
