VPIF display changes (Chaithrika)
Add platform device and resource structures. Also define a platform specific
clock setup function that can be accessed by the driver to configure the clock
and CPLD.
VPIF caputure changes (Murali)
1) Modify vpif_subdev_info to add board_info, routing information and
vpif interface configuration. Remove addr since it is part of
board_info
2) Add code to setup channel mode and input decoder path for vpif
capture driver
Also incorporated comments against version v0 of the patch series and
added a spinlock to protect writes to common registers
Tested on DM6467 on channel 0 using TVP514x. Following bootargs used
for drivers:
vpif_capture.ch0_bufsize=829440 vpif_display.ch2_bufsize=829440
Signed-off-by: Manjunath Hadli <mrh@ti.com>
Signed-off-by: Brijesh Jadav <brijesh.j@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM355 platform and board setup
This has platform and board setup changes to support vpfe capture
driver for DM355 EVMs.
Tested video capture on DM355 using tvp514x
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Denys Dmytriyenko <denis@denix.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM644x platform and board setup
This adds platform and board setup changes required to support
vpfe capture driver on DM644x
Tested video capture on DM6446 with tvp514x driver
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Reviewed-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Denys Dmytriyenko <denis@denix.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For best performance, codecs often setup linked triggered
transfers with a contiguous block of params, and that is when
this API is used. Setup/configuration of these parameter RAMs
is most efficient if they are contiguous.
There is an API to allocate a set of contiguous parameter RAMs and
a corresponding API to free a set of contiguous parameter RAMs
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds definitions for some DM365 IRQs that are used by
the codecs. Codecs will also use the IRQs.
Entries are being added to enable/disable IRQ's.
There is no use as such for these entires in the kernel itself.
Instead these will be used by the "linuxutils" package of the DVSDK.
For further information on IRQ muxing refer to
http://focus.ti.com/lit/ug/sprufg5a/sprufg5a.pdf
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds PINMUX entries for DM355 Display.
These will be used by the DM355 display driver.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data for the 8MB NOR flash
found on da850/omap-l138 EVM. Both NOR and NAND can
co-exist on da850/omap-l138 as they are using different
chip selects.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data for the 512MB NAND Flash
found on DA850/OMAP-L138 EVM. Currently it supports
only 1-bit ECC.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There are two instances of MMC/SD on da850/omap-l138.
Connector for the first instance is available on the
EVM. This patch adds support for this instance.
This patch also adds support for card detect and write
protect switches on da850/omap-l138 EVM.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform support for the graphic display
(Sharp LK043T1DG01) found on DA850/OMAP-L138 based EVM.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds a macro to convert the GPIO signal passed as bank number
and signal to GPIO pin number.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Define resources for McASP used on DA850/OMAP-L138 EVM, add platform
device defintion and Pin Mux configurations.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Define resources for McASP1 used on DA830/OMAP-L137 EVM, add platform
device defintion, initialization function. Additionally, this patch
also adds version and FIFO related members to platform data structure.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 has 144 pins configurable as GPIO, but
currently this has been configured as 128. This patch
corrects it.
Also, this patch adds the base address for GPIO pins
greater than 128.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Earlier patch which adds EMAC support for da850/omap-l138
was not configuring the MDIO pins.
Ethernet was working fine with the earlier patch, because
the MDIO pins were configured from the boot loader. This
patch removes that dependency.
Also, this patch populates a member in the emac clk structure
to say that EMAC LPSC sits on controller 1.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The mask can hold only 8 bit values. This gave a
compilation warning. This patch rectifies the warning.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
EDMA queues in DM365 are a little different than those
on other DaVinci's. On DM365 Q0 and Q1 have the larger
FIFO size. We want Q0 and Q1 to be used by codecs and
DVSDK demos.
MMC driver is the only driver which uses the flag
'EVENTQ_DEFAULT'. So MMC driver should be using Q2 instead of
Q1 on DM365.
This patch allows us to declare a "default queue" from
SOC specific code. If it is not declared then the EDMA
driver assumes a default of queue 1.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM365 and DM6467 have 4 queues. The patch updates the
'dma_event_q' enum to reflect this.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There is no need to pass clock name strings in platform_data.
Instead, setup clkdev nodes to have correct ASoC device names.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Ethernet Media Access Controller (EMAC) on da850/omap-l138
supports 10/100 Mbps operation. It also supports Media
Independent Interface (MII) and Reduced Media Independent
Interface (RMII) to physical layer (PHY).
Phy which supports MII is present on the DA850/OMAP-L138
base board and Phy supporting RMII is present on the
UI card. This patch adds support only for the MII Phy.
Support for RMII Phy will be added later.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for the DA850/OMAP-L138 Evaluation Module (EVM)
from TI. The EVM has User Interface (UI) card which contains
various devices. This UI card can be connected to the base
board. Support for all the devices on the UI card and ones on
the EVM will be added in subsequent patches.
The EVM schematics are not available publicly yet; but should
be available soon.
A new defconfig for this board has been added mainly because
the DA830/OMAP-L137 defconfig forces writethrough cache mode
which is not required on DA850/OMAP-L138.
This patch has been boot tested on DA850/OMAP-L138 EVM
using ramdisk as filesystem.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The DA850/OMAP-L138 is a new SoC from TI in the same family as
DA830/OMAP-L137.
Major changes include better support for power management,
support for SATA devices and McBSP (same IP as DM644x).
DA850/OMAP-L138 documents are available at
http://focus.ti.com/docs/prod/folders/print/omap-l138.html.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rearrange the PINMUX macros and pinmux_setup function which
are common between da830/omap-l137 and da850/omap-l138.
Also, replace the da830 string in function names to da8xx.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
With the introduction of TI da850/omap-l138, some of the macros
defined for da830/omap-l137 will be needed in da850 source file.
So, move the common macros to da8xx.h header file.
Also, modify the macro names from DA830_... to DA8XX_.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data and init function for IDE which could be called
from board specific file to register IDE device.
Note that for 594MHz device the transfer mode is limited to UDMA4 since ideclk
rate is less than 100 MHz, which forces udma_mask in palm_bk3710.c to UDMA4,
while for 729MHz device, it is UDMA5.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Make arch_idle and arch_reset inline as inline function.
Not having them inline leads to a warning of this sort when only
one of these functions is used:
arch/arm/mach-davinci/include/mach/system.h:24: warning: 'arch_reset' \
defined but not used
boot, re-boot tested on OMAP-L138 EVM
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch takes out IO mapping macros from mach/io.h and puts them in
mach/hardware.h avoiding need to include mach/io.h in various files such as
serial.h, vmalloc.h etc.
The main reason to avoid inclusion of mach/io.h is, when default in/out macros
are overridden by machine specific functions (e.g., in case of PCI I/O), they
result into linker error. An example snippet and error snapshot is listed below.
Following code in mach/io.h:
#define inl(p) my_inl()
static inline unsigned int my_inl(unsigned int addr)
{
if (IS_PCI_IO(addr))
return pci_inl ();
else
return le32_to_cpu(__raw_readl(__typesafe_io(addr)));
}
leads to error:
LD arch/arm/boot/compressed/vmlinux
arch/arm/boot/compressed/misc.o: In function `my_inl':
misc.c:(.text+0x2744): undefined reference to `pci_inl'
make[2]: *** [arch/arm/boot/compressed/vmlinux] Error 1
This is because mach/io.h gets included in arch/arm/boot/compressed/misc.c
through mach/serial.h but pci.c file, which defines 'pci_inl' doesn't get built
into compressed vmlinux.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
1) Registers the platform devices for ASP on dm355, dm644x and dm646x
so that the machine driver can probe to get ASP related platform
data.
2) Move towards definition of the asp clocks using physical name(for
dm355 and dm644x)
3) Add platform data to board specific files.
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Support DM365 GPIOs ... primarily by handling non-banked GPIO IRQs:
- Flag DM365 chips as using non-banked GPIO interrupts, using a
new soc_info field.
- Replace the gpio_to_irq() mapping logic. This now uses some
runtime infrastructure, keyed off that new soc_info field,
which doesn't handle irq_to_gpio().
- Provide a new irq_chip ... GPIO IRQs handled directly by AINTC
still need edge triggering managed by the GPIO controller.
DM365 chips no longer falsely report 104 GPIO IRQs as they boot.
Intelligence about IRQ muxing is missing, so for the moment this
only exposes the first eight DM365 GPIOs, which are never muxed.
The next eight are muxed, half with Ethernet (which uses most of
those pins anyway).
Tested on DM355 (10 unbanked IRQs _or_ 104 banked ones) and also
on DM365 (16 unbanked ones, only 8 made available).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for the DA830/OMAP-L137 Evaluation Module (EVM)
from TI. The EVM has User Interface (UI) and Audio cards
that can be connected which contain various devices.
Support for those devices and ones on the EVM will be
added in subsequent patches.
Additional generalizations for future SoCs in da8xx family done by
Sudhakar Rajashekhara and Sekhar Nori.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The da830/omap l137 is a new SoC from TI that is similar
to the davinci line. Since its so similar to davinci,
put the support for the da830 in the same directory as
the davinci code.
There are differences, however. Some of those differences
prevent support for davinci and da830 platforms to work
in the same kernel binary. Those differences are:
1) Different physical address for RAM. This is relevant
to Makefile.boot addresses and PHYS_OFFSET. The
Makefile.boot issue isn't truly a kernel issue but
it means u-boot won't work with a uImage including
both architectures. The PHYS_OFFSET issue is
addressed by the "Allow for runtime-determined
PHYS_OFFSET" patch by Lennert Buytenhek but it
hasn't been accepted yet.
2) Different uart addresses. This is only an issue
for the 'addruart' assembly macro when CONFIG_DEBUG_LL
is enabled. Since the code in that macro is called
so early (e.g., by _error_p in kernel/head.S when
the processor lookup fails), we can't determine what
platform the kernel is running on at runtime to use
the correct uart address.
These areas have compile errors intentionally inserted
to indicate to the builder they're doing something wrong.
A new config variable, CONFIG_ARCH_DAVINCI_DMx, is added
to distinguish between a true davinci architecture and
the da830 architecture.
Note that the da830 currently has an issue with writeback
data cache so CONFIG_CPU_DCACHE_WRITETHROUGH should be
enabled when building a da830 kernel.
Additional generalizations for future SoCs in the da8xx family done by
Sudhakar Rajashekhara and Sekhar Nori.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Mikhail Cherkashin <mcherkashin@ru.mvista.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch adds base support for new TI SOC DM365, which s
similar to the dm355.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
- restructure to support multiple channel controllers by using
additional struct resources for each CC
- interface changes visible to EDMA clients
Introduce macros to build IDs from controller and channel number,
and to extract them. Modify the edma_alloc_slot function to take an
extra argument for the controller.
Also update ASoC drivers to use API. ASoC changes
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- Move queue related mappings to dm<soc>.c
EDMA in DM355 and DM644x has two transfer controllers while DM646x
has four transfer controllers. Moving the queue to tc mapping and
queue priority mapping to dm<soc>.c will be helpful to probe these
mappings from platform device so that the machine_is_* testing will
be avoided.
- add channel mapping logic
Channel mapping logic is introduced in dm646x EDMA. This implies
that there is no fixed association for a channel number to a
parameter entry number. In other words, using the DMA channel
mapping registers (DCHMAPn), a PaRAM entry can be mapped to any
channel. While in the case of dm644x and dm355 there is a fixed
mapping between the EDMA channel and Param entry number.
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
Minimal support for the 4-bit ECC engine found on DM355, DM365,
DA830/OMAP-L137, and similar recent DaVinci-family chips.
This is limited to small-page flash for now; there are some page
layout issues for large page chips. Note that most boards using
this engine (like the DM355 EVM) include 2GiB large page chips.
Sanity tested on DM355 EVM after swapping the socketed NAND for
a small-page one.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Provide a generic SRAM allocator using genalloc, and vaguely
modeled after what AVR32 uses. This builds on top of the
static CPU mapping set up in the previous patch, and returns
DMA mappings as requested (if possible).
Compared to its OMAP cousin, there's no current support for
(currently non-existent) DaVinci power management code running
in SRAM; and this has ways to deallocate, instead of being
allocate-only.
The initial user of this should probably be the audio code,
because EDMA from DDR is subject to various dropouts on at
least DM355 and DM6446 chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Package on-chip SRAM. It's always accessible from the ARM, so
set up a standardized virtual address mapping into a 128 KiB
area that's reserved for platform use.
In some cases (dm6467) the physical addresses used for EDMA are
not the same as the ones used by the ARM ... so record that info
separately in the SOC data, for chips (unlike the OMAP-L137)
where SRAM may be used with EDMA.
Other blocks of SRAM, such as the ETB buffer or DSP L1/L2 RAM,
may be unused/available on some system. They are ignored here.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove remnants of dm6446-specific SRAM allocator, as preparation for
a more generic replacement.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Different SoC have different numbers of pinmux registers and other
resources that overlap with each other. To clean up the code and
eliminate defines that overlap with each other, move the PINMUX
defines to the SoC specific files.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The Timer64p timer has 8 compare registers that can
be used to generate interrupts when the timer value
matches the compare reg's value. They do not disturb
the timer itself. This can be useful when there is
only one timer available for both clock events and
clocksource.
When enabled, the clocksource remains a continuous
32-bit counter but the clock event will no longer
support periodic interrupts. Instead only oneshot
timers will be supported and implemented by setting
the compare register to the current timer value plus
the period that the clock event subsystem is requesting.
Compare registers support is enabled automatically
when the following conditions are met:
1) The same timer is being used for clock events
and clocksource.
2) The timer is the bottom half (32 bits) of the
64-bit timer (hardware limitation).
3) The the compare register offset and irq are
not zero.
Since the timer is always running, there is a hardware
race in timer32_config() between reading the current
timer value, and adding the period to the current
timer value and writing the compare register.
Testing on a da830 evm board with the timer clocked
at 24 MHz and the processor clocked at 300 MHz,
showed the number of counter ticks to do this ranged
from 20-53 (~1-2.2 usecs) but usually around 41 ticks.
This includes some artifacts from collecting the
information. So, the minimum period should be
at least 5 usecs to be safe.
There is also an non-critical lower limit that
the period should be since there is no point in
setting an event that is much shorter than the
time it takes to set the event, and get & handle
the timer interrupt for that event. There can
also be all sorts of delays from activities
occuring elsewhere in the system (including
hardware activitis like cache & TLB management).
These are virtually impossible to quantify so a
minimum period of 50 usecs was chosen. That will
certianly be enough to avoid the actual hardware
race but hopefully not large enough to cause
unreasonably course-grained timers.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Integrate the Common Platform Interrupt Controller (cp_intc)
support into the low-level irq handling for davinci and similar
platforms. Do it such that support for cp_intc and the original
aintc can coexist in the same kernel binary.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Factor out the code to extract that mac address from
i2c eeprom.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The dm644x and dm646x board files have i2c eeprom read and
write routines but they are not used so remove them.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Since most of the emac platform_data is really SoC specific
and not board specific, move it to the SoC-specific files.
Put a pointer to the platform_data in the soc_info structure
so the board-specific code can set some of the platform_data
if it needs to.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
