ivtv used tvaudio in the past and at the time tvaudio required V4L1.
Since tvaudio is no longer dependent on V4L1 and since ivtv actually
no longer uses tvaudio at all, this is no removed from Kconfig.
Without this patch ivtv won't be build if V4L1 is disabled.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a recommendation to select SND_USB_AUDIO for listing and
adds a documentation file for si470x.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx18: Disable write retries for registers that always change - part 1.
Interrupt related registers will likely not read back the value we just wrote.
Disable retries for these registers for now to avoid accidently discarding
interrupts. More intelligent read back verification criteria are needed for
these and other registers (e.g. GPIO line registers), which will be addressed in
subsequent changes.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Apparently the author of the saa7110 driver was confused by the
number of outputs returned by DECODER_GET_CAPABILITIES. Of course a
decoder chip has no analog ouputs, but it must have at least one
digital output.
* Fix an off-by-one error when checking the input value of
DECODER_SET_INPUT.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Attached is a patch that updates the cx88 documentation to add the fact the
closed caption works for at least NTSC capture.
ps: I also updated the wiki at:
http://www.linuxtv.org/v4lwiki/index.php/Text_capture#cx88_devices
Signed-off-by: Rafael Diniz <diniz@wimobilis.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The attached patch fix VBI support cx88 card.
I'm running a capture for hours, getting the closed caption from it[1], and
it's working perfect - the output is the same of a bttv card.
Please apply this patch as soon as possible.
[1] - using zvbi-ntsc-cc of zvbi project.
Signed-off-by: Rafael Diniz <diniz@wimobilis.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
config\tDVB_USB_CINERGY_T2 causes the make_kconfig.pl to forget to enable by default the compilation of cinergyT2 module.
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There already is an report at kernel bugzilla about this issue:
http://bugzilla.kernel.org/show_bug.cgi?id=9455
When enabling extra checks for the i2c-bus of cx88 based cards by
loading i2c_algo_bit with bit_test=1 this may trigger an oops
when loading cx88_dvb.
This is caused by the extra check code that detects that the
sda-line is stuck high and thus does not register the i2c-bus.
cx88-dvb however does not check if the i2c-bus is valid and just
uses core->i2c_adap to attach dvb frontend modules.
This leads to an oops at the first call to i2c_transfer:
$ modprobe i2c_algo_bit bit_test=1
$ modprobe cx8802
cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
cx88[0]: quirk: PCIPCI_NATOMA -- set TBFX
cx88[0]: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37,autodetected], frontend(s): 1
cx88[0]: TV tuner type 4, Radio tuner type -1
cx88[0]: SDA stuck high!
cx88[0]: i2c register FAILED
input: cx88 IR (Hauppauge Nova-S-Plus as /class/input/input5
cx88[0]/2: cx2388x 8802 Driver Manager
cx88-mpeg driver manager 0000:00:10.2: enabling device (0154 -> 0156)
cx88-mpeg driver manager 0000:00:10.2: PCI INT A -> Link[LNKD] -> GSI 9 (level, low) -> IRQ 9
cx88[0]/2: found at 0000:00:10.2, rev: 5, irq: 9, latency: 64, mmio: 0xfb000000
cx8802_probe() allocating 1 frontend(s)
cx88/2: cx2388x dvb driver version 0.0.6 loaded
cx88/2: registering cx8802 driver, type: dvb access: shared
cx88[0]/2: subsystem: 0070:9202, board: Hauppauge Nova-S-Plus DVB-S [card=37]
cx88[0]/2: cx2388x based DVB/ATSC card
BUG: unable to handle kernel NULL pointer dereference at 00000000
IP: [<e084d4ef>] :i2c_core:i2c_transfer+0x1f/0x80
*pde = 00000000
Modules linked in: cx88_dvb(+) cx8802 cx88xx ir_common i2c_algo_bit tveeprom videobuf_dvb btcx_risc
mga drm ipv6 fscpos eeprom nfsd exportfs stv0299 b2c2_flexcop_pci b2c2_flexcop cx24123 s5h1420 ves1x93
dvb_ttpci dvb_core saa7146_vv saa7146 videobuf_dma_sg videobuf_core videodev v4l1_compat ttpci_eeprom
lirc_serial lirc_dev usbhid rtc uhci_hcd 8139too i2c_piix4 i2c_core usbcore evdev
Pid: 4249, comm: modprobe Not tainted (2.6.27-gentoo #3)
EIP: 0060:[<e084d4ef>] EFLAGS: 00010296 CPU: 0
EIP is at i2c_transfer+0x1f/0x80 [i2c_core]
EAX: 00000000 EBX: ffffffa1 ECX: 00000002 EDX: d6c71e3c
ESI: d80cd050 EDI: d8093c00 EBP: d6c71e20 ESP: d6c71e0c
DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: driver could possibly stomp on resources outside of its scope
{mchehab@redhat.com: I got two versions of the same patch (identical,
except for whitespacing). One authored by Andy Burns and another
authored by Suresh Siddha. Due to that, I'm applying the one that has
less CodingStyle errors. I'm also adding both comments and the SOB's for
both patches, since they are both interesting}
Suresh Siddha commented:
Alexey Fisher reported:
> resource map sanity check conflict: 0xcfeff800 0xcff007ff 0xcfe00000
> 0xcfefffff PCI Bus 0000:01
BAR base is located in the middle of the 4K page and the hardcoded
size argument makes the request span two pages causing the conflict.
Fix the hard coded size argument in ioremap().
Andy Burns commented:
I have already sent this patch on the linux-dvb list, but it didn't get
much attention, so re-sending direct, I hope you all don't mind.
While attempting to run mythtv in a xen domU, I encountered problems
loading the driver for my saa7134 card, with an error from ioremap().
This error was due to the driver allocating an incorrectly sized mmio
area, which was trapped by xen's permission checks, but this would go
un-noticed on a kernel without xen.
My card has a 1K sized mmio area, I've had information that other cards
have 2K areas, perhaps others have different sizes, yet the driver
always attempts to map 4K. I realise that the granularity of mapping is
the page size, which typically would be 4K, but unless the card's base
address happens to fall on a 4K boundary (mine does not) then the
base+4K will end up spanning two pages, and this is when the error
occurs under xen.
My patch uses the pci_resource_len macro to determine the size required
for the user's particular card, instead of the hardcoded 4K value. I've
tested with a couple of printk() inside ioremap() that the start address
and size do get rounded to the closest page boundary.
With this patch I am able to successfully load the saa7134 driver and
run mythtv under xen with my card, subject to correct pollirq settings
in case of shared IRQ, I am still seeing occasional DMA panics, which I
think are related to swiotlb handling by dom0/domU, usually the panic
occurs when changing mux, once tuned to a mux, 12 hour continuous
recordings are possible without errors.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andy Burns <andy@burns.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove lock_kernel() call from cafe_ccic.c
Commit d56dc61265 added lock_kernel()
calls to cafe_ccic.c. But that driver was written with proper locking
and does not need the BKL, so take it back out.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the missing compat ioctls that are needed to
operate Skype in combination with libv4l and a MJPEG only camera.
If you think it's trivial enough please submit it to -stable, too.
Signed-off-by: Gregor Jasny <gjasny@web.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by David Ellingsworth:
> I'm not sure if it matters or not, but the ibmcam driver in the
> Mauro's linux-2.6 git tree in the for_linus branch is currently
> broken.
uvd is equal to NULL during most of ibmcam_probe. Due to that, an OOPS is
generated at dev_info. This patch replaces uvd->dev->dev to dev->dev
inside this routine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reviewed-by: David Ellingsworth <david@identd.dyndns.org>
This patch add support for new device named KWorld USB FM Radio
SnapMusic Mobile 700 (FM700).
And changes few lines in comments.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update Kconfig to add missing dependency on zl10353 for dtv5100 driver.
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rather than implementing different ways leading to confusion.
This allows multiple gate_enable/disable's in the tuner_read/write
functions, thereby lesser number of I/O operations throughout,
eventually leading to better results. As a side effect demods that
detect the STOP bit for auto closing of the gate can be avoided, thereby
a very minimal gain in disabling the auto detect feature as well.
Improves readability on the device control.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner-3036 and dpc7146 drivers have been deleted now so we can
remove the corresponding entries from feature-removal-schedule.txt.
(Thanks for doing this, BTW.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device is already handled by radio-si470x driver, and we
therefore want usbhid to ignore it.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Impact: fix incorrect locking triggered during hotplug-intense stress-tests
While migrating the the CB_IRQSAFE_UNLOCKED timers during a cpu-offline,
we queue them on the cb_pending list, so that they won't go
stale.
Thus, when the callbacks of the timers run from the softirq context,
they could run into potential deadlocks, since these callbacks
assume that they're running with irq's disabled, thereby annoying
lockdep!
Fix this by emulating hardirq context while running these callbacks from
the hrtimer softirq.
=================================
[ INFO: inconsistent lock state ]
2.6.27 #2
--------------------------------
inconsistent {in-hardirq-W} -> {hardirq-on-W} usage.
ksoftirqd/0/4 [HC0[0]:SC1[1]:HE1:SE0] takes:
(&rq->lock){++..}, at: [<c011db84>] sched_rt_period_timer+0x9e/0x1fc
{in-hardirq-W} state was registered at:
[<c014103c>] __lock_acquire+0x549/0x121e
[<c0107890>] native_sched_clock+0x88/0x99
[<c013aa12>] clocksource_get_next+0x39/0x3f
[<c0139abc>] update_wall_time+0x616/0x7df
[<c0141d6b>] lock_acquire+0x5a/0x74
[<c0121724>] scheduler_tick+0x3a/0x18d
[<c047ed45>] _spin_lock+0x1c/0x45
[<c0121724>] scheduler_tick+0x3a/0x18d
[<c0121724>] scheduler_tick+0x3a/0x18d
[<c012c436>] update_process_times+0x3a/0x44
[<c013c044>] tick_periodic+0x63/0x6d
[<c013c062>] tick_handle_periodic+0x14/0x5e
[<c010568c>] timer_interrupt+0x44/0x4a
[<c0150c9f>] handle_IRQ_event+0x13/0x3d
[<c0151c14>] handle_level_irq+0x79/0xbd
[<c0105634>] do_IRQ+0x69/0x7d
[<c01041e4>] common_interrupt+0x28/0x30
[<c047007b>] aac_probe_one+0x1a3/0x3f3
[<c047ec2d>] _spin_unlock_irqrestore+0x36/0x39
[<c01512b4>] setup_irq+0x1be/0x1f9
[<c065d70b>] start_kernel+0x259/0x2c5
[<ffffffff>] 0xffffffff
irq event stamp: 50102
hardirqs last enabled at (50102): [<c047ebf4>] _spin_unlock_irq+0x20/0x23
hardirqs last disabled at (50101): [<c047edc2>] _spin_lock_irq+0xa/0x4b
softirqs last enabled at (50088): [<c0128ba6>] do_softirq+0x37/0x4d
softirqs last disabled at (50099): [<c0128ba6>] do_softirq+0x37/0x4d
other info that might help us debug this:
no locks held by ksoftirqd/0/4.
stack backtrace:
Pid: 4, comm: ksoftirqd/0 Not tainted 2.6.27 #2
[<c013f6cb>] print_usage_bug+0x13e/0x147
[<c013fef5>] mark_lock+0x493/0x797
[<c01410b1>] __lock_acquire+0x5be/0x121e
[<c0141d6b>] lock_acquire+0x5a/0x74
[<c011db84>] sched_rt_period_timer+0x9e/0x1fc
[<c047ed45>] _spin_lock+0x1c/0x45
[<c011db84>] sched_rt_period_timer+0x9e/0x1fc
[<c011db84>] sched_rt_period_timer+0x9e/0x1fc
[<c01210fd>] finish_task_switch+0x41/0xbd
[<c0107890>] native_sched_clock+0x88/0x99
[<c011dae6>] sched_rt_period_timer+0x0/0x1fc
[<c0136dda>] run_hrtimer_pending+0x54/0xe5
[<c011dae6>] sched_rt_period_timer+0x0/0x1fc
[<c0128afb>] __do_softirq+0x7b/0xef
[<c0128ba6>] do_softirq+0x37/0x4d
[<c0128c12>] ksoftirqd+0x56/0xc5
[<c0128bbc>] ksoftirqd+0x0/0xc5
[<c0134649>] kthread+0x38/0x5d
[<c0134611>] kthread+0x0/0x5d
[<c0104477>] kernel_thread_helper+0x7/0x10
=======================
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I am trying out suspend, resume on an OMAP3 based board. What I see
during resume is that the SMC911x driver resume routing gets stuck
after trying to transmit the packet out of the controller. Some debug
messages below:
--> smc911x_drv_resume
eth0: --> smc911x_reset
eth0: smc911x_reset timeout waiting for PM restore
eth0: --> smc911x_enable
eth0: --> smc911x_phy_configure()
eth0: --> smc911x_phy_reset()
eth0: phy caps=0x782d
eth0: phy advertised caps=0x0de1
eth0: --> smc911x_phy_check_media
smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809
smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809
eth0: link down
Restarting tasks ... eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
eth0: --> smc911x_hard_start_xmit
eth0: --> smc911x_hardware_send_pkt
nfs: server 172.24.190.217 not responding, still trying
nfs: server 172.24.190.217 not responding, still trying
The following change makes it work fine: (The change within
smc911x_drv_probe function was to get rid of a compilation warning).
Signed-off-by: Romit Dasgupta <romit@ti.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When the iw_cxgb3 module's cxgb3_client "add" func gets called by the
cxgb3 module, the iwarp driver ends up calling the ethtool ops get_drvinfo
function in cxgb3 to get the fw version and other info. Currently the
iwarp driver grabs the rtnl lock around this down call to serialize.
As of 2.6.27 or so, things changed such that the rtnl lock is held around
the call to the netdev driver open function. Also the cxgb3_client "add"
function doesn't get called if the device is down.
So, if you load cxgb3, then load iw_cxgb3, then ifconfig up the device,
the iw_cxgb3 add func gets called with the rtnl_lock held. If you
load cxgb3, ifconfig up the device, then load iw_cxgb3, the add func
gets called without the rtnl_lock held. The former causes the deadlock,
the latter does not.
In addition, there are iw_cxgb3 sysfs handlers that also can call
down into cxgb3 to gather the fw and hw versions. These can be called
concurrently on different processors and at any time. Thus we need to
push this serialization down in the cxgb3 driver get_drvinfo func.
The fix is to remove rtnl lock usage, and use a per-device lock in cxgb3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Protect against invalid phy entries in the eeprom.
Extend eeprom access timeout.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The doorbell writes may be seen out of order by the firmware if they
are in WC memory since the tx spin(un)lock does not flush WC writes.
Hence if the "stop" is written on a different CPU than the "go", it
is possible that the stop will arrive after the go unless we add an
explicit memory barrier (and mmiowb() is not enough).
It fixes transmit hangs in multi tx queue mode.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Turned off CONFIG_PCI_LEGACY and turned on EXT4, and otherwise mostly
took the defaults. This also updates ppc6xx_defconfig, which covers
the 6xx/7xx/7xxx-based embedded boards.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new context may not be 16-byte aligned, so the real address of the
mcontext structure should be read from the uc_regs pointer instead of
directly using the (unaligned) uc_mcontext field.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Addresses in the hardware status page below index 0x20 are reserved for use
by the hardware. The legacy breadcrumb was sitting at index 5. Move it to
index 0x21, and make sure everyone uses the defined value instead of
hard-coded constants.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This fixes hangs on 855-class hardware by avoiding double attachment of the
driver due to the stub second head device having the same pci id as the real
device.
Other DRM drivers probably want this treatment as well, but I'm applying it
just to this one for safety. But we should clean up the drm_pciids.h mess
now so that each driver has its own pci id list header in its own directory.
Lets do that in the next release.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ehc->last_reset is used to ensure that resets are not issued too
close to each other. It's initialized to jiffies minus one minute
on EH entry. However, when new links are initialized after PMP is
probed, new links have zero for this timestamp resulting in long wait
depending on the current jiffies.
This patch makes last_set considered iff ATA_EHI_DID_RESET is set, in
which case last_reset is always initialized. As an added precaution,
WARN_ON() is added so that warning is printed if last_reset is
in future.
This problem is spotted and debugged by Shane Huang.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shane Huang <Shane.Huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Phillip O'Donnell <phillip.odonnell@gmail.com> pointed out that the same
sign extension bug that was fixed in commit ba14a9c2 ("libata: Avoid
overflow in ata_tf_to_lba48() when tf->hba_lbal > 127") also appears to
exist in ata_tf_read_block(). Fix this by adding a cast to u64.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I posted this last month, but was prompted to do so again in bz#467457
Add capability flag to support slave devices with pata_sch driver.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
No arguments named @deadline in cs5535_cable_detect() and
cs5536_cable_detect(). Remove them.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that the radeon driver has suspend/resume functions, it needs to map its
registers at load time or it will likely crash if a suspend operation occurs
before the driver has been initialized.
This patch moves the register mapping code from firstopen to load and makes
the mapping into a _DRM_DRIVER one so that the core won't remove it at
lastclose time.
Fixes (at least partially) kernel bz #11891.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
It's not used in any other drivers, and doesn't look like it will be from
drm.git master.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
When userland detected that this ioctl was supported (by version number check),
it used it in a racy way -- dispatch delayed swap, wait for vblank, continue
rendering. As there was no mechanism for it to wait for the swap to finish,
sometimes it would render before the swap and garbage would be displayed on
the screen.
By removing the ioctl and returning -EINVAL, userland returns to its previous,
correct rendering path of waiting for a vblank then dispatching a swap. The
only path that could have used this ioctl correctly was page flipping, which
relied on only one client running and emitting wait-for-vblank-before-rendering
in the command stream. That path also falls back correctly, at the performance
cost of not being able to queue up rendering before the flip occurs.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This probably just means the chipset doesn't support MSI, which is fine.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This could return early when reading after writing a buffer, if somebody
had already put it on the flushing list (write domains are 0, but still
active), leading to glReadPixels failure.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This corresponds to the setup of the sarea pointers in DMA initialization,
though neither is exactly the point at which the sarea is set up or torn down.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This register is set by the 2D driver to prevent lockups, and so it needs to
be preserved across suspend/resume too. This makes my X200s work.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Impact: fix hang/crash on ia64 under high load
This is ugly, but the simplest patch by far.
Unlike other similar routines, account_group_exec_runtime() could be
called "implicitly" from within scheduler after exit_notify(). This
means we can race with the parent doing release_task(), we can't just
check ->signal != NULL.
Change __exit_signal() to do spin_unlock_wait(&task_rq(tsk)->lock)
before __cleanup_signal() to make sure ->signal can't be freed under
task_rq(tsk)->lock. Note that task_rq_unlock_wait() doesn't care
about the case when tsk changes cpu/rq under us, this should be OK.
Thanks to Ingo who nacked my previous buggy patch.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Doug Chapman <doug.chapman@hp.com>
Before commit b6c40d68ff ("net: only
invoke dev->change_rx_flags when device is UP"), the dsa driver could
sort-of get away with only fiddling with the master interface's
allmulti/promisc counts in ->change_rx_flags() and not touching them
in ->open() or ->stop(). After this commit (note that it was merged
almost simultaneously with the dsa patches, which is why this wasn't
caught initially), the breakage that was already there became more
apparent.
Since it makes no sense to keep the master interface's allmulti or
promisc count pinned for a slave interface that is down, copy the vlan
driver's sync logic (which does exactly what we want) over to dsa to
fix this.
Bug report from Dirk Teurlings <dirk@upexia.nl> and Peter van Valderen
<linux@ddcrew.com>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dsa slave interface has a mac address that differs from that
of the master interface, eth_type_trans() won't explicitly set
skb->pkt_type back to PACKET_HOST -- we need to do this ourselves
before calling eth_type_trans().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since skb_reset_tail_pointer() reads skb->data, we need to set
skb->data before calling skb_reset_tail_pointer(). This was causing
spurious skb_over_panic()s from skb_put() being called on a recycled
skb that had its skb->tail set to beyond where it should have been.
Bug report from Peter van Valderen <linux@ddcrew.com>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmpmsg_put() can happily corrupt kernel memory, using a static
table and forgetting to reset an array index in a loop.
Remove the static array since its not safe without proper locking.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mac80211/debugfs_sta.c
The trailing zero was written to state[4], it's out of bounds.
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: removal of unnecessary looping
The lockless part of the ring buffer allows for reentry into the code
from interrupts. A timestamp is taken, a test is preformed and if it
detects that an interrupt occurred that did tracing, it tries again.
The problem arises if the timestamp code itself causes a trace.
The detection will detect this and loop again. The difference between
this and an interrupt doing tracing, is that this will fail every time,
and cause an infinite loop.
Currently, we test if the loop happens 1000 times, and if so, it will
produce a warning and disable the ring buffer.
The problem with this approach is that it makes it difficult to perform
some types of tracing (tracing the timestamp code itself).
Each trace entry has a delta timestamp from the previous entry.
If a trace entry is reserved but and interrupt occurs and traces before
the previous entry is commited, the delta timestamp for that entry will
be zero. This actually makes sense in terms of tracing, because the
interrupt entry happened before the preempted entry was commited, so
one may consider the two happening at the same time. The order is
still preserved in the buffer.
With this idea, instead of trying to get a new timestamp if an interrupt
made it in between the timestamp and the test, the entry could simply
make the delta zero and continue. This will prevent interrupts or
tracers in the timer code from causing the above loop.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Daniel J Blueman