This patch adds a new debugfs entry 'device_status' in
/sys/kernel/debug/rssd. The value of this entry shows
devices online and those in the process of removing.
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix to return 0 from pci probe in case of rebuild. If not, pci consider
probe has failed, and crash during rmmod.
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To recover from command timeouts, reset the device. In addition
to that improved timeout handling of PIO commands.
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As found by gcc-4.8, the QUEUE_SYSFS_BIT_FNS macro creates functions
that use a value generated by queue_var_store independent of whether
that value was set or not.
block/blk-sysfs.c: In function 'queue_store_nonrot':
block/blk-sysfs.c:244:385: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
Unlike most other such warnings, this one is not a false positive,
writing any non-number string into the sysfs files indeed has
an undefined result, rather than returning an error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The rt2800pci driver supports the built-in wireless
MAC of the Ralink RT3x5x SoCs. However building the
driver for these SoCs leads to the following error:
LD init/built-in.o
drivers/built-in.o: In function `rt2800pci_rxdone_tasklet':
<...>/drivers/net/wireless/rt2x00/rt2800pci.c:1012: undefined reference to `rt2x00pci_rxdone'
drivers/built-in.o:(.rodata+0x4780): undefined reference to `rt2x00pci_initialize'
drivers/built-in.o:(.rodata+0x4784): undefined reference to `rt2x00pci_uninitialize'
drivers/built-in.o:(.rodata+0x47bc): undefined reference to `rt2x00pci_flush_queue'
drivers/built-in.o:(.rodata+0x4818): undefined reference to `rt2x00pci_regbusy_read'
make[5]: *** [vmlinux] Error 1
The missing functions are provided by the rt2x00pci
module. This module is only selected by the rt2800pci
driver if PCI support is enabled in the kernel, because
some parts of the rt2x00pci code depends on PCI support.
PCI support is not available on the RT3x5x SoCs because
those have no PCI host controller at all.
Move the non PCI specific code from rt2x00pci into a
separate module. This makes it possible to use that
code even if PCI support is disabled. The affected
functions are used by all of the rt2x00 PCI drivers
so select the new module for those drivers.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BugLink: http://bugs.launchpad.net/bugs/1128840
It appears that when this register read fails it never recovers, so
I think there is no need to repeat the same error message ad infinitum.
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: users@rt2x00.serialmonkey.com
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_complete_reset will not be called if ath9k_hw_reset
is unsuccessful, so we need to re-enable intertupts to
balence the previous ath_prepare_reset call. Also schedule a
reset as a best effort method to recover the chip from
whatever state caused the channel change failure.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=55771
Signed-off-by: Robert Shade <robert.shade@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nvram contains critical initialization parameter for firmware to run. Host
driver should not proceed if nvram fails to be downloaded to dongle.
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multiple cipher suites have been programmed then the lowest
suite is to be retured. This fixes issue when AP mode is using
CCMP and TKIP WPA combination where rekeying will fail.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
on stop_ap the dongle was not properly shutdown. As a result it was
not possible to restart AP or STA after AP operation without
restarting the device. This patch will fix that.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx and rx michael tkip keys are always swapped in case being
configured per mac. This is wrong for AP. The swap should only
be done for STA mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are waiting on first scan command of internal scan request
before association, so we should complete on last internal scan
command response.
Cc: <stable@vger.kernel.org> # 3.8
Tested-by: Daniel Drake <dsd@laptop.org>
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
merge window. Fortunately, Cai and Christian noticed before 3.9
shipped.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n1ir
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Unfortunately, we introduced some big-endian bugs during the last
merge window. Fortunately, Cai and Christian noticed before 3.9
shipped."
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix big-endian bugs which could cause fs corruptions
Pull reiserfs fix from Jan Kara:
"A fix for reiserfs xattr bug exposed by changes to lookup_one_len()"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
reiserfs: Fix warning and inode leak when deleting inode with xattrs
Pull s390 fixes from Martin Schwidefsky:
"Just a bunch of bugfixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: provide emtpy check_pgt_cache() function
s390/uaccess: fix page table walk
s390/3270: fix minor_start issue
s390/uaccess: fix clear_user_pt()
s390/scm_blk: fix error return code in scm_blk_init()
s390/scm_block: fix printk format string
drivers/Kconfig: add several missing GENERIC_HARDIRQS dependencies
When an extent was zeroed out, we forgot to do convert from cpu to le16.
It could make us hit a BUG_ON when we try to write dirty pages out. So
fix it.
[ Also fix a bug found by Dmitry Monakhov where we were missing
le32_to_cpu() calls in the new indirect punch hole code.
There are a number of other big endian warnings found by static code
analyzers, but we'll wait for the next merge window to fix them all
up. These fixes are designed to be Obviously Correct by code
inspection, and easy to demonstrate that it won't make any
difference (and hence, won't introduce any bugs) on little endian
architectures such as x86. --tytso ]
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: CAI Qian <caiqian@redhat.com>
Reported-by: Christian Kujau <lists@nerdbynature.de>
Cc: Dmitry Monakhov <dmonakhov@openvz.org>
CONFIG_LPAE doesn't exist: the correct option is CONFIG_ARM_LPAE, so fix
up the two typos under arch/arm/.
The fix to head.S is slightly scary, but this is just for setting up
an early io-mapping for the serial port when running on a big-endian,
LPAE system. Since these systems don't exist in the wild (at least, I
have no access to one outside of kvmtool, which doesn't provide a serial
port suitable for earlyprintk), then we can revisit the code later if it
causes any problems.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add unwind annotations to the ftrace assembly code so that the function
tracer's stacktracing options (func_stack_trace, etc.) work when
CONFIG_ARM_UNWIND is enabled.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 70264367a2 ("ARM: 7653/2: do not scale loops_per_jiffy when
using a constant delay clock") fixed a problem with our timer-based
delay loop, where loops_per_jiffy is scaled by cpufreq yet used directly
by the timer delay ops.
This patch fixes the problem in a more elegant way by keeping a private
ticks_per_jiffy field in the delay ops, independent of loops_per_jiffy
and therefore not subject to scaling. The loop-based delay continues to
use loops_per_jiffy directly, as it should.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Cortex-A15 (r0p0..r3p2) the TLBI/DSB are not adequately shooting down
all use of the old entries. This patch implements the erratum workaround
which consists of:
1. Dummy TLBIMVAIS and DSB on the CPU doing the TLBI operation.
2. Send IPI to the CPUs that are running the same mm (and ASID) as the
one being invalidated (or all the online CPUs for global pages).
3. CPU receiving the IPI executes a DMB and CLREX (part of the exception
return code already).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit b8db6b8 (ARM: 7547/4: cache-l2x0: add support for Aurora L2 cache
ctrl) moved the masking of the part ID which caused the RTL version to be
lost. Commit 6248d06 (ARM: 7545/1: cache-l2x0: make outer_cache_fns a
field of l2x0_of_data) changed how .set_debug is initialized. Both commits
break commit 74ddcdb (ARM: 7608/1: l2x0: Only set .set_debug
on PL310 r3p0 and earlier) which uses the RTL version to conditionally set
.set_debug function pointer. Commit b8db6b8 also caused the printed cache
ID to be missing the version information.
Fix this by reverting how the part number is masked so the RTL version
info is maintained. The cache-id-part DT property does not set the RTL
bits so masking them should have no effect. Also, re-arrange the order
of the function pointer init so the .set_debug function can be overridden.
Reported-by: Paolo Pisati <paolo.pisati@canonical.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jason Cooper reports these build errors:
arch/arm/kernel/built-in.o: In function `iwmmxt_do':
/.../arch/arm/kernel/pj4-cp0.c:36: undefined reference to `iwmmxt_task_release'
/.../arch/arm/kernel/pj4-cp0.c:40: undefined reference to `iwmmxt_task_switch'
make: *** [vmlinux] Error 1
This is caused because the PJ4 code explicitly references the iWMMXt
code, but doesn't require it to be built. Fix this by ensuring that
iWMMXt is always enabled with PJ4.
Reported-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The C-Media CM6631 USB receiver doesn't respond to changes in sample rate
while the interface is active. The same behavior is observed in other UAC2
hardware like the VIA VT1731.
Reset the interface after setting the sampling frequency on sample rate
changes, to ensure that the sample rate set by snd_usb_init_sample_rate() is
used. Otherwise, the device will try to use the sample rate of the previous
stream, causing distorted sound on sample rate changes.
The reset is performed for all UAC2 devices, as it should not affect a
standards compliant device, but it is only necessary for C-Media CM6631,
VIA VT1731 and possibly others.
Failure to read sample rate from the device is not handled as an error in
set_sample_rate_v2(), as (permanent or intermittent) failure to read sample
rate isn't essential for a successful sample rate set.
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fengguang Wu's 0-Day kernel build testing backend found the
following build error for an allmodconfig build on ia64:
drivers/built-in.o: In function `show_yoffset':
>> bgrt.c:(.text+0xe5a71): undefined reference to `bgrt_tab'
>> bgrt.c:(.text+0xe5a91): undefined reference to `bgrt_tab'
drivers/built-in.o: In function `show_xoffset':
>> bgrt.c:(.text+0xe5b51): undefined reference to `bgrt_tab'
>> bgrt.c:(.text+0xe5b71): undefined reference to `bgrt_tab'
drivers/built-in.o: In function `show_type':
>> bgrt.c:(.text+0xe5c31): undefined reference to `bgrt_tab'
drivers/built-in.o:bgrt.c:(.text+0xe5c51): more undefined references to `bgrt_tab' follow
drivers/built-in.o: In function `bgrt_init':
bgrt.c:(.init.text+0x8931): undefined reference to `bgrt_image'
bgrt.c:(.init.text+0x8932): undefined reference to `bgrt_image_size'
bgrt.c:(.init.text+0x8950): undefined reference to `bgrt_image'
bgrt.c:(.init.text+0x8960): undefined reference to `bgrt_image_size'
The problem is that all these undefined names are provided by
arch/x86/platform/efi/efi-bgrt.c - which is obviously not available
to the ia64 build.
It doesn't seem useful to provide the BGRT support for Itanium
(many systems are headless and have no graphics at all). So
just don't let users configure this driver on non-X86 machines.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The bitmask used for the prefix mangling was being calculated
incorrectly, leading to the wrong part of the address being replaced
when the prefix length wasn't a multiple of 32.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pull networking fixes from David Miller:
1) Fix VSOCK layer handling of context ID changes, from Reilly Grant.
2) Now that we have a synchronize_net() in netdev_rx_handler_unregister(),
we can't let any call sites hold locks. Unfortunately bonding does,
so we have to drop the rwlock there a little bit earlier, fix from
Veaceslav Falico.
3) MAC address setting loop exits one iteration too early in mlx4
driver, from Yan Burman.
4) Restore ipv6 routes properly upon ifdown/ifup of loopback, from
Balakumaran Kannan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
VSOCK: Handle changes to the VMCI context ID.
net IPv6 : Fix broken IPv6 routing table after loopback down-up
cbq: incorrect processing of high limits
net/mlx4_en: Fix setting initial MAC address
bonding: get netdev_rx_handler_unregister out of locks
A small collection of fixes. The most important ones are those from
Stephen and Lars-Peter both of which fix cache issues that have been
lurking for a while but not manifesting noticably enough for anyone to
report them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=QF+V
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A small collection of fixes. The most important ones are those from
Stephen and Lars-Peter both of which fix cache issues that have been
lurking for a while but not manifesting noticably enough for anyone to
report them."
* tag 'regmap-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: async: Add missing return
regmap: don't corrupt work buffer in _regmap_raw_write()
regmap: cache Fix regcache-rbtree sync
regmap: Initialize `map->debugfs' before regcache
Pull DRM fixes from Dave Airlie:
"Two core fixes, both regressions, along with some intel and some
nouveau fixes for regressions and oopses"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: correctly restore mappings if drm_open fails
drm/nouveau: fix NULL ptr dereference from nv50_disp_intr()
drm/nouveau: fix handling empty channel list in ioctl's
drm: don't unlock in the addfb error paths
drm/i915: Fix build failure
drm/i915: Be sure to turn hsync/vsync back on at crt enable (v2)
drm/i915: duct-tape locking when eDP init fails
Pull MIPS fixes from Ralf Baechle:
"A collection of fixes pretty much across the MIPS code. Even the
change to include/linux/signal.h by David Howells' 2a1486981c ("Fix
breakage in MIPS siginfo handling") should be considered MIPS-specific
as it touches an ifdefed segment that is only relevant to MIPS and
which unfortunately can't be made to go away entirely."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
Fix breakage in MIPS siginfo handling
Revert "MIPS: BCM63XX: Call board_register_device from device_initcall()"
MIPS: BCM63XX: Make nvram checksum failure non fatal
MIPS: Fix code generation for non-DSP capable CPUs
MIPS: Fix inconsistent formatting inside /proc/cpuinfo
MIPS: SEAD3: Enable LL/SC.
MIPS: Get rid of CONFIG_CPU_HAS_LLSC again
MIPS: Add dependencies for HAVE_ARCH_TRANSPARENT_HUGEPAGE
MIPS: VR4133: Fix probe for LL/SC.
MIPS: Fix logic errors in bitops.c
MIPS: Use CONFIG_CPU_MIPSR2 in csum_partial.S
MIPS: compat: Return same error ENOSYS as native for invalid operation.
This is a fix for commit 7897e60227 ("PCI: Disable Bus Master
unconditionally in pci_device_shutdown()"). Vivek reported that
with this commit, kexec failed because none of his SATA disks
came up.
A ->shutdown() callback might put the device in D3cold, which means config
space is no longer available.
[bhelgaas: changelog]
Link: https://lkml.org/lkml/2013/3/12/529
Reported-and-Tested-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 8c33f51df4.
Conflicts:
drivers/acpi/pci_root.c
This commit broke some pre-1.1 PCIe devices by leaving them with
ASPM enabled. Previously, we had disabled ASPM on these devices
because many of them don't implement it correctly (per 149e1637).
Requesting _OSC control early means that aspm_disabled may be set
before we scan the PCI bus and configure link ASPM state. But the
ASPM configuration currently skips the check for pre-PCIe 1.1 devices
when aspm_disabled is set, like this:
acpi_pci_root_add
acpi_pci_osc_support
if (flags != base_flags)
pcie_no_aspm
aspm_disabled = 1
pci_acpi_scan_root
...
pcie_aspm_init_link_state
pcie_aspm_sanity_check
if (!aspm_disabled)
/* check for pre-PCIe 1.1 device */
Therefore, setting aspm_disabled early means that we leave ASPM enabled
on these pre-PCIe 1.1 devices, which is a regression for some devices.
The best fix would be to clean up the ASPM init so we can evaluate
_OSC before scanning the bug (that way boot-time and hot-add discovery
will work the same), but that requires significant rework.
For now, we'll just revert the _OSC change as the lowest-risk fix.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=55211
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
CC: stable@vger.kernel.org # v3.8+
Commit fca460f95e simplified the x32
implementation by creating a syscall bitmask, equal to 0x40000000, that
could be applied to x32 syscalls such that the masked syscall number
would be the same as a x86_64 syscall. While that patch was a nice
way to simplify the code, it went a bit too far by adding the mask to
syscall_get_nr(); returning the masked syscall numbers can cause
confusion with callers that expect syscall numbers matching the x32
ABI, e.g. unmasked syscall numbers.
This patch fixes this by simply removing the mask from syscall_get_nr()
while preserving the other changes from the original commit. While
there are several syscall_get_nr() callers in the kernel, most simply
check that the syscall number is greater than zero, in this case this
patch will have no effect. Of those remaining callers, they appear
to be few, seccomp and ftrace, and from my testing of seccomp without
this patch the original commit definitely breaks things; the seccomp
filter does not correctly filter the syscalls due to the difference in
syscall numbers in the BPF filter and the value from syscall_get_nr().
Applying this patch restores the seccomp BPF filter functionality on
x32.
I've tested this patch with the seccomp BPF filters as well as ftrace
and everything looks reasonable to me; needless to say general usage
seemed fine as well.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Link: http://lkml.kernel.org/r/20130215172143.12549.10292.stgit@localhost
Cc: <stable@vger.kernel.org>
Cc: Will Drewry <wad@chromium.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
If first drm_open fails, the error-handling path will
incorrectly restore inode's mapping to NULL. This can
cause the crash later on. Fix by separately storing
away mapping pointers that drm_open can touch and
restore each from its own respective variable if the
call fails.
Fixes: https://bugzilla.novell.com/show_bug.cgi?id=807850
(thanks to Michal Hocko for investigating investigating and
finding the root cause of the bug)
Reference:
http://lists.freedesktop.org/archives/dri-devel/2013-March/036564.html
v2: Use one variable to store file and inode mapping
since they are the same at the function entry.
Fix spelling mistakes in commit message.
v3: Add reference to the original bug report.
Reported-by: Marco Munderloh <munderl@tnt.uni-hannover.de>
Tested-by: Marco Munderloh <munderl@tnt.uni-hannover.de>
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
One locking regression fix, and a couple of other i915 ones.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm: don't unlock in the addfb error paths
drm/i915: Fix build failure
drm/i915: Be sure to turn hsync/vsync back on at crt enable (v2)
drm/i915: duct-tape locking when eDP init fails
The VMCI context ID of a virtual machine may change at any time. There
is a VMCI event which signals this but datagrams may be processed before
this is handled. It is therefore necessary to be flexible about the
destination context ID of any datagrams received. (It can be assumed to
be correct because it is provided by the hypervisor.) The context ID on
existing sockets should be updated to reflect how the hypervisor is
currently referring to the system.
Signed-off-by: Reilly Grant <grantr@vmware.com>
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 Routing table becomes broken once we do ifdown, ifup of the loopback(lo)
interface. After down-up, routes of other interface's IPv6 addresses through
'lo' are lost.
IPv6 addresses assigned to all interfaces are routed through 'lo' for internal
communication. Once 'lo' is down, those routing entries are removed from routing
table. But those removed entries are not being re-created properly when 'lo' is
brought up. So IPv6 addresses of other interfaces becomes unreachable from the
same machine. Also this breaks communication with other machines because of
NDISC packet processing failure.
This patch fixes this issue by reading all interface's IPv6 addresses and adding
them to IPv6 routing table while bringing up 'lo'.
==Testing==
Before applying the patch:
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$
After applying the patch:
$ route -A inet6
Kernel IPv6 routing
table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$
Signed-off-by: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com>
Signed-off-by: Maruthi Thotad <Maruthi.Thotad@ap.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
currently cbq works incorrectly for limits > 10% real link bandwidth,
and practically does not work for limits > 50% real link bandwidth.
Below are results of experiments taken on 1 Gbit link
In shaper | Actual Result
-----------+---------------
100M | 108 Mbps
200M | 244 Mbps
300M | 412 Mbps
500M | 893 Mbps
This happen because of q->now changes incorrectly in cbq_dequeue():
when it is called before real end of packet transmitting,
L2T is greater than real time delay, q_now gets an extra boost
but never compensate it.
To fix this problem we prevent change of q->now until its synchronization
with real time.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Reviewed-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that msg pointer is set back to error value in case of
MSG_COPY flag is set and desired message to copy wasn't found. This
garantees that msg is either a error pointer or a copy address.
Otherwise the last message in queue will be freed without unlinking from
the queue (which leads to memory corruption) and the dummy allocated
copy won't be released.
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 6bbb6d9 "net/mlx4_en: Optimize Rx fast path filter checks" introduced a regression
under which the MAC address read from the card was not converted correctly
(the most significant byte was not handled), fix that.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that netdev_rx_handler_unregister contains synchronize_net(), we need
to call it outside of bond->lock, cause it might sleep. Also, remove the
already unneded synchronize_net().
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a quiet set of fixes for 3.9-rc4, a lot of people woke up and sent
urgent fixes for 3.9. I pushed back on a number of them that got
deferred to 3.10, but these are the ones that seemed important.
Regression in 3.9:
- Multiple regressions in OMAP2+ clock cleanup
- SH-Mobile frame buffer bug fix that merged here because of maintainer MIA
- ux500 prcmu changes broke DT booting
- MMCI duplicated regulator setup on ux500
- New ux500 clock driver broke ethernet on snowball
- Local interrupt driver for mvebu broke ethernet
- MVEBU GPIO driver did not get set up right on Orion DT
- incorrect interrupt number on Orion crypto for DT
Long-standing bugs, including candidates for stable:
- Kirkwood MMC needs to disable invalid card detect pins
- MV SDIO pinmux was wrong on Mirabox
- GoFlex Net board file needs to set NAND chip delay
- MSM timer restart race
- ep93xx early debug code broke in 3.7
- i.MX CPU hotplug race
- Incorrect clock setup for OMAP1 USB
- Workaround for bad clock setup by some old OMAP4 boot loaders
- Static I/O mappings on cns3xxx since 3.2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=oQbL
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"After a quiet set of fixes for 3.9-rc4, a lot of people woke up and
sent urgent fixes for 3.9. I pushed back on a number of them that got
deferred to 3.10, but these are the ones that seemed important.
Regression in 3.9:
- Multiple regressions in OMAP2+ clock cleanup
- SH-Mobile frame buffer bug fix that merged here because of
maintainer MIA
- ux500 prcmu changes broke DT booting
- MMCI duplicated regulator setup on ux500
- New ux500 clock driver broke ethernet on snowball
- Local interrupt driver for mvebu broke ethernet
- MVEBU GPIO driver did not get set up right on Orion DT
- incorrect interrupt number on Orion crypto for DT
Long-standing bugs, including candidates for stable:
- Kirkwood MMC needs to disable invalid card detect pins
- MV SDIO pinmux was wrong on Mirabox
- GoFlex Net board file needs to set NAND chip delay
- MSM timer restart race
- ep93xx early debug code broke in 3.7
- i.MX CPU hotplug race
- Incorrect clock setup for OMAP1 USB
- Workaround for bad clock setup by some old OMAP4 boot loaders
- Static I/O mappings on cns3xxx since 3.2"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: cns3xxx: fix mapping of private memory region
arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
arm: orion5x: correct IRQ used in dtsi for mv_cesa
arm: orion5x: fix orion5x.dtsi gpio parameters
ARM: Kirkwood: fix unused mvsdio gpio pins
arm: mvebu: Use local interrupt only for the timer 0
ARM: kirkwood: Fix chip-delay for GoFlex Net
ARM: ux500: Enable the clock controlling Ethernet on Snowball
ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
fbdev: sh_mobile_lcdc: fixup B side hsync adjust settings
ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
ARM: msm: Stop counting before reprogramming clockevent
ARM: ep93xx: Fix wait for UART FIFO to be empty
ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
ARM: OMAP4: clock data: lock USB DPLL on boot
ARM: OMAP1: fix USB host on 1710
From Anton Vorontsov <anton@enomsg.org>:
This tag includes Mac Lin's work to revive CNS3xxx booting:
"Since commit 0536bdf33f (ARM: move iotable mappings within the vmalloc
region), [...] the pre-defined iotable mappings is not in the vmalloc
region. [...] move the iotable mappings into the vmalloc region, and
merge the MPCore private memory region (containing the SCU, the GIC and
the TWD) as a single region."
Plus there is a small cosmetic fix, also from Mac Lin.
* tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx:
ARM: cns3xxx: fix mapping of private memory region
[arnd: dropped the cosmetic fix from the merge as it is not needed for 3.9]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit ac3ebafa81 "ACPI / idle: remove usage of the statedata"
changed the percpu processor cstate to a unified cstate in ACPI idle.
That caused all our NHM boxes to boot hang or panic.
2178751 Task dump for CPU 1:
2178752 swapper/1 R running task 6736 0 1 0x00000000
2178753 ffff8801e8029dc8 ffffffff8101cf96 ffff8801e8029e28 ffffffff813d294b
2178754 0000000000000f99 0000000000000003 00000000003cf654 0000000025c17d03
2178755 ffff8801e8029e38 ffff8801e74fc000 00000002590dc5c4 ffffffff8163cdb0
2178756 Call Trace:
2178757 [<ffffffff8101cf96>] ? acpi_processor_ffh_cstate_enter+0x2d/0x2f
2178758 [<ffffffff813d294b>] acpi_idle_enter_bm+0x1b1/0x236
2178759 [<ffffffff8163cdb0>] ? disable_cpuidle+0x10/0x10
2178760 [<ffffffff8163cdc2>] cpuidle_enter+0x12/0x14
2178761 [<ffffffff8163d286>] cpuidle_wrap_enter+0x2f/0x6d
2178762 [<ffffffff8163d2d4>] cpuidle_enter_tk+0x10/0x12
2178763 [<ffffffff8163cdd6>] cpuidle_enter_state+0x12/0x3a
2178764 [<ffffffff8163d4a7>] cpuidle_idle_call+0xe8/0x161
2178765 [<ffffffff81008d99>] cpu_idle+0x5e/0xa4
2178766 [<ffffffff8174c6c1>] start_secondary+0x1a9/0x1ad
2178767 Task dump for CPU 2:
In fact, the ACPI idle is based on the assumption of difference percpu
cstate structures that are necessary for the implementation to work
cprrectly. A unique acpi_processor_cx is not sifficient by far.
This patch is just a quick fix re-introducing the percpu cstates.
If someone really wants to unify the ACPI cstates, please make sure
that the whole software infrastructure is changed and take hardware
as well as many different kinds of BIOS settings into account.
[rjw: Changelog]
Reported-by: LKP project <lkp@linux.intel.com>
Reported-by: Xie ChanglongX <changlongx.xie@intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI handle of struct i2c_adapter's dev member should not be
set, because this causes that struct i2c_adapter to be associated
with the ACPI device node corresponding to its parent as the
second "physical_device", which is incorrect (this happens during
the registration of struct i2c_adapter). Consequently,
acpi_i2c_register_devices() should use the ACPI handle of the
parent of the struct i2c_adapter it is called for rather than the
struct i2c_adapter's ACPI handle (which should be NULL).
Make that happen and modify the i2c-designware-platdrv driver,
which currently is the only driver for ACPI-enumerated I2C
controller chips, not to set the ACPI handle for the
struct i2c_adapter it creates.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
It should be "governor".
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
