The gpio-chip device attributes were never destroyed when the device was
removed.
Fix by using device_create_with_groups() to create the device attributes
of the chip class device.
Note that this also fixes the attribute-creation race with userspace.
Fixes: d8f388d8dc ("gpio: sysfs interface")
Cc: stable <stable@vger.kernel.org> # v2.6.27+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MLB+ 3-pin mode pin group to R8A7791 PFC driver.
Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The R8A7791 manual sometimes calls the signal MLB_CLK and sometimes MLB_CK; the
latter can only be encountered in the PFC section and is probably just a typo
(this signal is always called MLB_CLK in the R8A7790 manual). Fix occurences
of MLB_CK throughout the R8A7791 PFC driver.
Based on original patch by Andrey Gusakov <andrey.gusakov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should not touch the packet after a netif_rx: it might
get freed behind our back.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Recent Leaf firmware versions (>= 3.1.557) do not allow to send
commands for non-existing channels. If a command is sent for a
non-existing channel, the firmware crashes.
Reported-by: Christopher Storah <Christopher.Storah@invetech.com.au>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in very high frequency (*), closing the CAN channel while
all the transmissions are on (#), opening the device again (@),
then sending a small number of packets would make the driver
enter an almost infinite loop of:
[....]
[15959.853988] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853990] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853991] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853993] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853994] kvaser_usb 4-3:1.0 can0: cannot find free context
[15959.853995] kvaser_usb 4-3:1.0 can0: cannot find free context
[....]
_dragging the whole system down_ in the process due to the
excessive logging output.
Initially, this has caused random panics in the kernel due to a
buggy error recovery path. That got fixed in an earlier commit.(%)
This patch aims at solving the root cause. -->
16 tx URBs and contexts are allocated per CAN channel per USB
device. Such URBs are protected by:
a) A simple atomic counter, up to a value of MAX_TX_URBS (16)
b) A flag in each URB context, stating if it's free
c) The fact that ndo_start_xmit calls are themselves protected
by the networking layers higher above
After grabbing one of the tx URBs, if the driver noticed that all
of them are now taken, it stops the netif transmission queue.
Such queue is worken up again only if an acknowedgment was received
from the firmware on one of our earlier-sent frames.
Meanwhile, upon channel close (#), the driver sends a CMD_STOP_CHIP
to the firmware, effectively closing all further communication. In
the high traffic case, the atomic counter remains at MAX_TX_URBS,
and all the URB contexts remain marked as active. While opening
the channel again (@), it cannot send any further frames since no
more free tx URB contexts are available.
Reset all tx URB contexts upon CAN channel close.
(*) 50 parallel instances of `cangen0 -g 0 -ix`
(#) `ifconfig can0 down`
(@) `ifconfig can0 up`
(%) "can: kvaser_usb: Don't free packets when tight on URBs"
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Flooding the Kvaser CAN to USB dongle with multiple reads and
writes in high frequency caused seemingly-random panics in the
kernel.
On further inspection, it seems the driver erroneously freed the
to-be-transmitted packet upon getting tight on URBs and returning
NETDEV_TX_BUSY, leading to invalid memory writes and double frees
at a later point in time.
Note:
Finding no more URBs/transmit-contexts and returning NETDEV_TX_BUSY
is a driver bug in and out of itself: it means that our start/stop
queue flow control is broken.
This patch only fixes the (buggy) error handling code; the root
cause shall be fixed in a later commit.
Acked-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
use of regmap_read() and regmap_write() in c_can_hw_raminit_syscon()
is not safe as the RAMINIT register can be shared between different drivers
at least for TI SoCs.
To make the modification atomic we switch to using regmap_update_bits().
regmap_update_bits() skips writing to the register if it's read content is the
same as what is going to be written. This causes an issue for us when we
need to clear the DONE bit with the initial condition START:0, DONE:1 as
DONE bit must be written with 1 to clear it.
So we defer the clearing of DONE bit to later when we set the START bit.
There we are sure that START bit is changed from 0 to 1 so the write of
1 to already set DONE bit will happen.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During the CAN FD standardization process within the ISO it turned out that
the failure detection capability has to be improved.
The CAN in Automation organization (CiA) defined the already implemented CAN
FD controllers as 'non-ISO' and the upcoming improved CAN FD controllers as
'ISO' compliant. See at http://www.can-cia.com/index.php?id=1937
Finally there will be three types of CAN FD controllers in the future:
1. ISO compliant (fixed)
2. non-ISO compliant (fixed, like the M_CAN IP v3.0.1 in m_can.c)
3. ISO/non-ISO CAN FD controllers (switchable, like the PEAK USB FD)
So the current M_CAN driver for the M_CAN IP v3.0.1 has to expose its non-ISO
implementation by setting the CAN_CTRLMODE_FD_NON_ISO ctrlmode at startup.
As this bit cannot be switched at configuration time CAN_CTRLMODE_FD_NON_ISO
must not be set in ctrlmode_supported of the current M_CAN driver.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When changing flags in the CAN drivers ctrlmode the provided new content has to
be checked whether the bits are allowed to be changed. The bits that are to be
changed are given as a bitfield in cm->mask. Therefore checking against
cm->flags is wrong as the content can hold any kind of values.
The iproute2 tool sets the bits in cm->mask and cm->flags depending on the
detected command line options. To be robust against bogus user space
applications additionally sanitize the provided flags with the provided mask.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The linux-can upstream git repositories are now hosted on kernel.org, update
MAINTAINERS accordingly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 5f893b2639 "tracing: Move enabling tracepoints to just after
rcu_init()" broke the enabling of system call events from the command
line. The reason was that the enabling of command line trace events
was moved before PID 1 started, and the syscall tracepoints require
that all tasks have the TIF_SYSCALL_TRACEPOINT flag set. But the
swapper task (pid 0) is not part of that. Since the swapper task is the
only task that is running at this early in boot, no task gets the
flag set, and the tracepoint never gets reached.
Instead of setting the swapper task flag (there should be no reason to
do that), re-enabled trace events again after the init thread (PID 1)
has been started. It requires disabling all command line events and
re-enabling them, as just enabling them again will not reset the logic
to set the TIF_SYSCALL_TRACEPOINT flag, as the syscall tracepoint will
be fooled into thinking that it was already set, and wont try setting
it again. For this reason, we must first disable it and re-enable it.
Link: http://lkml.kernel.org/r/1421188517-18312-1-git-send-email-mpe@ellerman.id.au
Link: http://lkml.kernel.org/r/20150115040506.216066449@goodmis.org
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
trace_init() calls init_ftrace_syscalls() and then calls trace_event_init()
which also calls init_ftrace_syscalls(). It makes more sense to only
call it from trace_event_init().
Calling it twice wastes memory, as it allocates the syscall events twice,
and loses the first copy of it.
Link: http://lkml.kernel.org/r/54AF53BD.5070303@huawei.com
Link: http://lkml.kernel.org/r/20150115040505.930398632@goodmis.org
Reported-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If the function graph tracer traces a jprobe callback, the system will
crash. This can easily be demonstrated by compiling the jprobe
sample module that is in the kernel tree, loading it and running the
function graph tracer.
# modprobe jprobe_example.ko
# echo function_graph > /sys/kernel/debug/tracing/current_tracer
# ls
The first two commands end up in a nice crash after the first fork.
(do_fork has a jprobe attached to it, so "ls" just triggers that fork)
The problem is caused by the jprobe_return() that all jprobe callbacks
must end with. The way jprobes works is that the function a jprobe
is attached to has a breakpoint placed at the start of it (or it uses
ftrace if fentry is supported). The breakpoint handler (or ftrace callback)
will copy the stack frame and change the ip address to return to the
jprobe handler instead of the function. The jprobe handler must end
with jprobe_return() which swaps the stack and does an int3 (breakpoint).
This breakpoint handler will then put back the saved stack frame,
simulate the instruction at the beginning of the function it added
a breakpoint to, and then continue on.
For function tracing to work, it hijakes the return address from the
stack frame, and replaces it with a hook function that will trace
the end of the call. This hook function will restore the return
address of the function call.
If the function tracer traces the jprobe handler, the hook function
for that handler will not be called, and its saved return address
will be used for the next function. This will result in a kernel crash.
To solve this, pause function tracing before the jprobe handler is called
and unpause it before it returns back to the function it probed.
Some other updates:
Used a variable "saved_sp" to hold kcb->jprobe_saved_sp. This makes the
code look a bit cleaner and easier to understand (various tries to fix
this bug required this change).
Note, if fentry is being used, jprobes will change the ip address before
the function graph tracer runs and it will not be able to trace the
function that the jprobe is probing.
Link: http://lkml.kernel.org/r/20150114154329.552437962@goodmis.org
Cc: stable@vger.kernel.org # 2.6.30+
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Using just the filter for checking for trampolines or regs is not enough
when updating the code against the records that represent all functions.
Both the filter hash and the notrace hash need to be checked.
To trigger this bug (using trace-cmd and perf):
# perf probe -a do_fork
# trace-cmd start -B foo -e probe
# trace-cmd record -p function_graph -n do_fork sleep 1
The trace-cmd record at the end clears the filter before it disables
function_graph tracing and then that causes the accounting of the
ftrace function records to become incorrect and causes ftrace to bug.
Link: http://lkml.kernel.org/r/20150114154329.358378039@goodmis.org
Cc: stable@vger.kernel.org
[ still need to switch old_hash_ops to old_ops_hash ]
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
As the set_ftrace_filter affects both the function tracer as well as the
function graph tracer, the ops that represent each have a shared
ftrace_ops_hash structure. This allows both to be updated when the filter
files are updated.
But if function graph is enabled and the global_ops (function tracing) ops
is not, then it is possible that the filter could be changed without the
update happening for the function graph ops. This will cause the changes
to not take place and may even cause a ftrace_bug to occur as it could mess
with the trampoline accounting.
The solution is to check if the ops uses the shared global_ops filter and
if the ops itself is not enabled, to check if there's another ops that is
enabled and also shares the global_ops filter. In that case, the
modification still needs to be executed.
Link: http://lkml.kernel.org/r/20150114154329.055980438@goodmis.org
Cc: stable@vger.kernel.org # 3.17+
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The s390x ABI requires to zero extend parameters before functions
are called.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In sk_load_byte_msh() sk_load_byte_slow() is called instead of
sk_load_byte_msh_slow(). Fix this and call the correct function.
Besides of this load only one byte instead of two and fix the comment.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the offset parameter for skb_copy_bits is changed in
sk_load_word() and sk_load_half(). Therefore it is not correct when
calling skb_copy_bits(). Fix this and use the original offset
for the function call.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The skb_copy_bits() function has the following signature:
int skb_copy_bits(const struct sk_buff *skb, int offset, void *to, int len)
Currently in bpf_jit.S the "to" and "len" parameters have been
exchanged. So fix this and call the function with the correct
parameters.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently the signed COMPARE HALFWORD IMMEDIATE (chi) and COMPARE (c)
instructions are used to compare "A" with "K". This is not correct
because "A" and "K" are both unsigned. To fix this remove the
chi instruction (no unsigned analogon available) and use the
unsigned COMPARE LOGICAL (cl) instruction instead of COMPARE (c).
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Other tunnels like GRE break while VxLAN offloads are enabled in Skyhawk-R. To
avoid this, we should restrict offload features on a per-packet basis in such
conditions.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull thermal fixes from Zhang Rui:
"Specifics:
- bogus type qualifier fix in OF thermal code.
- Minor fixes on imx and rcar thermal drivers.
- Update TI SoC thermal maintainer entry.
- Updated documentation of OF cpufreq cooling register"
* 'thermal-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: rcar: Spelling/grammar: s/drier use .../driver uses ...s/
thermal: rcar: change type of ctemp in rcar_thermal_update_temp()
thermal: rcar: fix ENR register value
Documentation: thermal: document of_cpufreq_cooling_register()
Thermal: imx: add clk disable/enable for suspend/resume
MAINTAINERS: update ti-soc-thermal status
MAINTAINERS: Add linux-omap to list of reviewers for TI Thermal
thermal: of: Remove bogus type qualifier for of_thermal_get_trip_points()
The final set of fixes for v3.19. Two of the fixes are
related to dwc3 scatter/gather implementation when we have
more requests queued than available TRBs, while the other
is a build fix for mv-usb PHY.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUtqoQAAoJEIaOsuA1yqRENP4QAJSfu3O8cOepIVnyIAZfnEdT
BauykTwkZj/LfH2B+6v6cacFVCSr7nuRb7bZ+dTgVykqClzCEIySqahnQEAt65u9
ergvINYZpi/t7B6DsNK7OHYyIyXKnFGmBr3R8jiHBRbJ832e/3bIZ/0pdFAmwpah
qhoGtjg0wNolF4ILXAFu3ghB/AkWBulCAwumMpldv+5p6wNzJRV72Vnto0pPpqYo
C8W6f1aXXx3C8kqv5cU60lmPT85q+CCjtaLPoCneo7KTtSqM4xQgf78M02LUNYFl
1qymKr3rWxYic6b+VEODA9y/NTBhQz0fy5JhEide6T8+eaQc+QpYSGAO+bxVK1fi
CHpdF7Yg83TAwT/HCztirqMl1TmkXc2x/NFgzY0di5NMqgDhodC+3vVtnHZPoX5S
W0g5D4QlGk0mYANx4kvijvLGBbjR/OtAv6OrK96Qvia1Vv9Nb4jrxg4PN/jbwXbR
nQ8qtU1a1AIqBYE92GIjFIiZIxFPpWzddlnRcbX1wh/1Qr2C8jsFnNQ6QwS2tyw2
HH0pVRpCLCA0oLgrCE47Y+aSHaJ5t7EsxYmb+fhi/5prOHdsggHTBQSPl526NiK+
UJ8HWm2h6sel1/JdEITT+plrn62b8UL7Vd5hYQrVewgkyDrXSIpVRYA1V1dBg40U
kEQDS7JvFdFP46IRh/Cw
=iLKs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.19-rc6
The final set of fixes for v3.19. Two of the fixes are
related to dwc3 scatter/gather implementation when we have
more requests queued than available TRBs, while the other
is a build fix for mv-usb PHY.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are a few fixes for reported problems including a possible
null-deref on probe with keyspan, a misbehaving modem, and a couple of
issues with the USB console.
Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJUtivAAAoJEEEN5E/e4bSV6eEQALGHzwqFXAZvWQRuAIA6yEYy
7KFDtU2bPBLorm6vDFPc9J3Q8Nh8cSwoMneJrrdKZiXoEoRrK5R9Mj34ENTrNNCX
HwbjHx0QS3OysG3L09uciMxZbtHBZvr72s08QEJrLM9jgzKWdOBJORNeuUihw6vr
YnxbAvpM4XPmb2PZ3GcvtP9tY12Kbh6Gb8kViaxn9jXFrLyjdsZq9TBqFlmFpwzs
rk1wSIyo3dnQ41umKcalwqqni03pmdh+JMhXsWUXtFYExknvxQIpvzivUPHjX9pp
OA1y8AX5l2MAUH2DVPSmPPwjDu4AMT3MLkdzonPNPSmvRPPoygEINaAVY6yxhImj
nnXUCQKz4YEPBw9YGh4lsYLJlTthV+oit2QS65aJf/itBJYo0lGZUKFX9luHBQZD
dQ7xYwT9fAmpUZVhNSZDVf6uDCv6fOn3Q5/R5ivTRdLjlTys6xS7FTDVgqzAB0tL
ztM2P8ujexUt4CYMT28lqy8JbLsTqCRjoyKuuDeiIa1/QaanxIRXeUfj6TUYR9Rz
9LT+a0V05fWakzzCgyKFD6ul8l1KLzu2pV2Xk35JB+0oyRFr495wcGqS+la85djS
KXG664RNOtXrsmbjKQFTsJ3MdShcbbyS9gOubLWlp74lNsMVKl5MLACUAyOWuB6o
HYYC0VCVce1rJKI08s3P
=umHr
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v3.18-rc5
Here are a few fixes for reported problems including a possible
null-deref on probe with keyspan, a misbehaving modem, and a couple of
issues with the USB console.
Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull networking fixes from David Miller:
1) Don't use uninitialized data in IPVS, from Dan Carpenter.
2) conntrack race fixes from Pablo Neira Ayuso.
3) Fix TX hangs with i40e, from Jesse Brandeburg.
4) Fix budget return from poll calls in dnet and alx, from Eric
Dumazet.
5) Fix bugus "if (unlikely(x) < 0)" test in AF_PACKET, from Christoph
Jaeger.
6) Fix bug introduced by conversion to list_head in TIPC retransmit
code, from Jon Paul Maloy.
7) Don't use GFP_NOIO under spinlock in USB kaweth driver, from Alexey
Khoroshilov.
8) Fix bridge build with INET disabled, from Arnd Bergmann.
9) Fix netlink array overrun for PROBE attributes in openvswitch, from
Thomas Graf.
10) Don't hold spinlock across synchronize_irq() in tg3 driver, from
Prashant Sreedharan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
tg3: Release tp->lock before invoking synchronize_irq()
tg3: tg3_reset_task() needs to use rtnl_lock to synchronize
tg3: tg3_timer() should grab tp->lock before checking for tp->irq_sync
team: avoid possible underflow of count_pending value for notify_peers and mcast_rejoin
openvswitch: packet messages need their own probe attribtue
i40e: adds FCoE configure option
cxgb4vf: Fix queue allocation for 40G adapter
netdevice: Add missing parentheses in macro
bridge: only provide proxy ARP when CONFIG_INET is enabled
neighbour: fix base_reachable_time(_ms) not effective immediatly when changed
net: fec: fix MDIO bus assignement for dual fec SoC's
xen-netfront: use different locks for Rx and Tx stats
drivers: net: cpsw: fix multicast flush in dual emac mode
cxgb4vf: Initialize mdio_addr before using it
net: Corrected the comment describing the ndo operations to reflect the actual prototype for couple of operations
usb/kaweth: use GFP_ATOMIC under spin_lock in usb_start_wait_urb()
MAINTAINERS: add me as ibmveth maintainer
tipc: fix bug in broadcast retransmit code
update ip-sysctl.txt documentation (v2)
net/at91_ether: prepare and unprepare clock
...
Prashant Sreedharan says:
====================
tg3: synchronize_irq() should be called without taking locks
v2: Added Reported-by, Tested-by fields and reference to the thread that
reported the problem
This series addresses the problem reported by Peter Hurley in mail thread
https://lkml.org/lkml/2015/1/12/1082
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
synchronize_irq() can sleep waiting, for pending IRQ handlers so driver
should release the tp->lock spin lock before invoking synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tg3_reset_task() uses only tp->lock for synchronizing with code
paths like tg3_open() etc. But since tp->lock is released before doing
synchronize_irq(), rtnl_lock should be taken in tg3_reset_task() to
synchronize it with other code paths.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to avoid the race between tg3_timer() and the execution paths
which does not invoke tg3_timer_stop() and releases tp->lock before
calling synchronize_irq()
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
but otherwise things are calm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUtonAAAoJEL/70l94x66DeaUH/0ZKXvCUkrfhXMwjgWFkEA/X
zF3wm6Et7tn+5UdRTPaO9ko9HmmIZJBlZqVu9+RFFbPBFthzZDdGGXUUjVoKvWgS
2dMejNvf3a+tw9ovXCQwr7Uy1TTqysIQP+0fcOTRJlH4peh1RTEr1JF5IEI3pM0q
gWAsQIqijiDUg8rLYQOBBqL/Mz2j09K4YYORS548JESXdQBcBJf3nkAeaeh7RNhw
QDt2dH9rCgLFAWdmg0wmKq12CCcHr01aZav11u30OLUEr9OcGpl9ohMqiFYJr1o9
9aV/xk7BDBgxEXZpkpth3ziovAQ8Z6MmczykSZFLNMElhYi0V3DMNYm13SCTLBM=
=uUFZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Two bugfixes for arm64. I will have another pull request next week,
but otherwise things are calm"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm64: KVM: Fix HCR setting for 32bit guests
arm64: KVM: Fix TLB invalidation by IPA/VMID
This patch is fixing a race condition that may cause setting
count_pending to -1, which results in unwanted big bulk of arp messages
(in case of "notify peers").
Consider following scenario:
count_pending == 2
CPU0 CPU1
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers
atomic_add (adding 1 to count_pending)
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 1)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to 0)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test (dec count_pending to -1)
Fix this race by using atomic_dec_if_positive - that will prevent
count_pending running under 0.
Fixes: fc423ff00d ("team: add peer notification")
Fixes: 492b200efd ("team: add support for sending multicast rejoins")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 fixes from Martin Schwidefsky:
"Two small performance tweaks, the plumbing for the execveat system
call and a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uprobes: fix user space PER events
s390/bpf: Fix JMP_JGE_X (A > X) and JMP_JGT_X (A >= X)
s390/bpf: Fix ALU_NEG (A = -A)
s390/mm: avoid using pmd_to_page for !USE_SPLIT_PMD_PTLOCKS
s390/timex: fix get_tod_clock_ext() inline assembly
s390: wire up execveat syscall
s390/kernel: use stnsm 255 instead of stosm 0
s390/vtime: Get rid of redundant WARN_ON
s390/zcrypt: kernel oops at insmod of the z90crypt device driver
User space is currently sending a OVS_FLOW_ATTR_PROBE for both flow
and packet messages. This leads to an out-of-bounds access in
ovs_packet_cmd_execute() because OVS_FLOW_ATTR_PROBE >
OVS_PACKET_ATTR_MAX.
Introduce a new OVS_PACKET_ATTR_PROBE with the same numeric value
as OVS_FLOW_ATTR_PROBE to grow the range of accepted packet attributes
while maintaining to be binary compatible with existing OVS binaries.
Fixes: 05da589 ("openvswitch: Add support for OVS_FLOW_ATTR_PROBE.")
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tracked-down-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds FCoE config option I40E_FCOE, so that FCoE can be enabled
as needed but otherwise have it disabled by default.
This also eliminate multiple FCoE config checks, instead now just
one config check for CONFIG_I40E_FCOE.
The I40E FCoE was added with 3.17 kernel and therefore this patch
shall be applied to stable 3.17 kernel also.
CC: <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=k0Aw
-----END PGP SIGNATURE-----
Merge tag 'locks-v3.19-1' of git://git.samba.org/jlayton/linux
Pull file locking fix from Jeff Layton:
"Just a simple bugfix for a regression that I introduced into v3.18
with the internal lease API overhaul -- mea culpa. Kudos to Linda and
Neil for tracking this down and fixing it"
* tag 'locks-v3.19-1' of git://git.samba.org/jlayton/linux:
locks: fix NULL-deref in generic_delete_lease
For example, one could conceivably call
for_each_netdev_in_bond_rcu(condition ? bond1 : bond2, slave)
and get an unexpected result.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block layer fixes from Jens Axboe:
"The major part is an update to the NVMe driver, fixing various issues
around surprise removal and hung controllers. Most of that is from
Keith, and parts are simple blk-mq fixes or exports/additions of minor
functions to aid this effort, and parts are changes directly to the
NVMe driver.
Apart from the above, this contains:
- Small blk-mq change from me, killing an unused member of the
hardware queue structure.
- Small fix from Ming Lei, fixing up a few drivers that didn't
properly check for ERR_PTR() returns from blk_mq_init_queue()"
* 'for-linus' of git://git.kernel.dk/linux-block:
NVMe: Fix locking on abort handling
NVMe: Start and stop h/w queues on reset
NVMe: Command abort handling fixes
NVMe: Admin queue removal handling
NVMe: Reference count admin queue usage
NVMe: Start all requests
blk-mq: End unstarted requests on a dying queue
blk-mq: Allow requests to never expire
blk-mq: Add helper to abort requeued requests
blk-mq: Let drivers cancel requeue_work
blk-mq: Export if requests were started
blk-mq: Wake tasks entering queue on dying
blk-mq: get rid of ->cmd_size in the hardware queue
block: fix checking return value of blk_mq_init_queue
block: wake up waiters when a queue is marked dying
NVMe: Fix double free irq
blk-mq: Export freeze/unfreeze functions
blk-mq: Exit queue on alloc failure
When IPV4 support is disabled, we cannot call arp_send from
the bridge code, which would result in a kernel link error:
net/built-in.o: In function `br_handle_frame_finish':
:(.text+0x59914): undefined reference to `arp_send'
:(.text+0x59a50): undefined reference to `arp_tbl'
This makes the newly added proxy ARP support in the bridge
code depend on the CONFIG_INET symbol and lets the compiler
optimize the code out to avoid the link error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 958501163d ("bridge: Add support for IEEE 802.11 Proxy ARP")
Cc: Kyeyoon Park <kyeyoonp@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
DWC3 gadget sets up a pool of 32 TRBs for each EP during initialization. This
means, the max TRBs that can be submitted for an EP is fixed to 32. Since the
request queue for an EP is a linked list, any number of requests can be queued
to it by the gadget layer. However, the dwc3 driver must not submit TRBs more
than the pool it has created for. This limit wasn't respected when SG was used
resulting in submitting more than the max TRBs, eventually leading to
non-transfer of the TRBs submitted over the max limit.
Root cause:
When SG is used, there are two loops iterating to prepare TRBs:
- Outer loop over the request_list
- Inner loop over the SG list
The code was missing break to get out of the outer loop.
Fixes: eeb720fb21 (usb: dwc3: gadget: add support for SG lists)
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When scatter gather (SG) is used, multiple TRBs are prepared from one DWC3
request (dwc3_request). So while preparing TRBs, the 'last' flag should be set
only when it is the last TRB being prepared from the last dwc3_request entry.
The current implementation uses list_is_last to check if the dwc3_request is the
last entry from the request_list. However, list_is_last returns false for the
last entry too. This is because, while preparing the first TRB from a request,
the function dwc3_prepare_one_trb modifies the request's next and prev pointers
while moving the URB to req_queued. Hence, list_is_last always returns false no
matter what.
The correct way is not to access the modified pointers of dwc3_request but to
use list_empty macro instead.
Fixes: e5ba5ec833 (usb: dwc3: gadget: fix scatter gather implementation)
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Unregister gpiochip device (used to export information through sysfs)
before removing it internally. This way removal will reverse addition.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move direct and indirect calls to gpiochip_remove_pin_ranges outside of
spin lock as they can end up taking a mutex in pinctrl_remove_gpio_range.
Note that the pin ranges are already added outside of the lock.
Fixes: 9ef0d6f762 ("gpiolib: call pin removal in chip removal function")
Fixes: f23f1516b6 ("gpiolib: provide provision to register pin ranges")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix memory leak and sleep-while-atomic in gpiochip_remove.
The memory leak was introduced by afa82fab5e ("gpio / ACPI: Move event
handling registration to gpiolib irqchip helpers") that moved the
release of acpi interrupt resources to gpiochip_irqchip_remove, but by
then the resources are no longer accessible as the acpi_gpio_chip has
already been freed by acpi_gpiochip_remove.
Note that this also fixes a few potential sleep-while-atomics, which has
been around since 1425052097 ("gpio: add IRQ chip helpers in gpiolib")
when the call to gpiochip_irqchip_remove while holding a spinlock was
added (a couple of irq-domain paths can end up grabbing mutexes).
Fixes: afa82fab5e ("gpio / ACPI: Move event handling registration to
gpiolib irqchip helpers")
Fixes: 1425052097 ("gpio: add IRQ chip helpers in gpiolib")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix potential corruption of gpio-chip list due to failure to remove the
chip from the list before returning in gpiochip_add error path.
The chip could be long gone when the global list is next traversed,
something which could lead to a null-pointer dereference. In the best
case (chip not deallocated) we are just leaking the gpio range.
Fixes: 14e85c0e69 ("gpio: remove gpio_descs global array")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Memory allocated and references taken by of_gpiochip_add and
acpi_gpiochip_add were never released on errors in gpiochip_add (e.g.
failure to find free gpio range).
Fixes: 391c970c0d ("of/gpio: add default of_xlate function if device
has a node pointer")
Fixes: 664e3e5ac6 ("gpio / ACPI: register to ACPI events
automatically")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
marco chip has been dropped, clear its support.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>