The controller provides trace FIFO DFX tool to assist link fault debugging
and link optimization. This tool can be helpful when debugging link faults
without SAS analyzers. Each PHY has an independent trace FIFO interface.
The user can configure the trace FIFO tool of one PHY by using the
following six interfaces:
signal_sel: select signal group applies to different scenarios.
0x0: linkrate negotiation
0x1: Host 12G TX train
0x2: Disk 12G TX train
0x3: SAS PHY CTRL DFX 0
0x4: SAS PHY CTRL DFX 1
0x5: SAS PCS DFX
other: linkrate negotiation
dump_mask: The masked hardware status bit will not be updated.
dump_mode: determines how to dump data after trigger signal is generated.
0x0: dump forever
0x1: dump 32 data after trigger signal is generated
0x2: no more dump after trigger signal is generated
trigger_mode: determines the trigger mode, level or edge.
0x0: dump when trigger signal changed
0x1: dump when trigger signal's level equal to trigger_level
0x2: dump when trigger signal's level different from trigger_level
trigger_level: determines the trigger level.
trigger_msk: mask trigger signal
The user can get 32-byte values from hardware by reading the rd_data.
These values consitute the status record of the hardware at different time
points.
Link: https://lore.kernel.org/r/1611659068-131975-6-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the controller reset occurs at the same time as driver removal, it may
be possible that the interrupts have been released prior to the host
softreset, and calling pci_irq_vector() there causes a WARN:
WARNING: CPU: 37 PID: 1542 /pci/msi.c:1275 pci_irq_vector+0xc0/0xd0
Call trace:
pci_irq_vector+0xc0/0xd0
disable_host_v3_hw+0x58/0x5b0 [hisi_sas_v3_hw]
soft_reset_v3_hw+0x40/0xc0 [hisi_sas_v3_hw]
hisi_sas_controller_reset+0x150/0x260 [hisi_sas_main]
hisi_sas_rst_work_handler+0x3c/0x58 [hisi_sas_main]
To fix, flush the driver workqueue prior to releasing the interrupts to
ensure any resets have been completed.
Link: https://lore.kernel.org/r/1611659068-131975-5-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a config option to enable debugfs support by default. And if debugfs
support is enabled by default, dump count default value is increased to 50
as generally users want something bigger than the current default in that
situation.
Link: https://lore.kernel.org/r/1611659068-131975-4-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that v2 and v3 hw expose their HW queues (and so shost.nr_hw_queues is
set), remove the conditional checks in hisi_sas_task_prep().
This change would affect v1 HW performance (as it does not expose HW
queues), but nobody uses it and support may be dropped soon.
Link: https://lore.kernel.org/r/1611659068-131975-3-git-send-email-john.garry@huawei.com
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The platform_get_irq() check for -EPROBE_DEFER was to ensure that all the
steps to add the SCSI host are not done and then only to realise that the
probe needs to be deferred.
However, since there is now an earlier check for this in
hisi_sas_interrupt_preinit(), this check is superfluous and may be removed.
Link: https://lore.kernel.org/r/1611659068-131975-2-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
libsas event notifiers required an extension where gfp_t flags must be
explicitly passed. For bisectability, a temporary _gfp() variant of such
functions were added. All call sites then got converted use the _gfp()
variants and explicitly pass GFP context. Having no callers left, the
original libsas notifiers were then modified to accept gfp_t flags by
default.
Switch back to the original libas API, while still passing GFP context.
The libsas _gfp() variants will be removed afterwards.
Link: https://lore.kernel.org/r/20210118100955.1761652-14-a.darwish@linutronix.de
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the new libsas event notifiers API, which requires callers to
explicitly pass the gfp_t memory allocation flags.
Below are the context analysis for modified functions:
=> hisi_sas_bytes_dmaed():
Since it is invoked from both process and atomic contexts, let its callers
pass the gfp_t flags:
* hisi_sas_main.c:
------------------
hisi_sas_phyup_work(): workqueue context
-> hisi_sas_bytes_dmaed(..., GFP_KERNEL)
hisi_sas_controller_reset_done(): has an msleep()
-> hisi_sas_rescan_topology()
-> hisi_sas_phy_down()
-> hisi_sas_bytes_dmaed(..., GFP_KERNEL)
hisi_sas_debug_I_T_nexus_reset(): calls wait_for_completion_timeout()
-> hisi_sas_phy_down()
-> hisi_sas_bytes_dmaed(..., GFP_KERNEL)
* hisi_sas_v1_hw.c:
-------------------
int_abnormal_v1_hw(): irq handler
-> hisi_sas_phy_down()
-> hisi_sas_bytes_dmaed(..., GFP_ATOMIC)
* hisi_sas_v[23]_hw.c:
----------------------
int_phy_updown_v[23]_hw(): irq handler
-> phy_down_v[23]_hw()
-> hisi_sas_phy_down()
-> hisi_sas_bytes_dmaed(..., GFP_ATOMIC)
=> int_bcast_v1_hw() and phy_bcast_v3_hw():
Both are invoked exclusively from irq handlers. Pass GFP_ATOMIC.
Link: https://lore.kernel.org/r/20210118100955.1761652-12-a.darwish@linutronix.de
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
LLDDs report events to libsas with .notify_port_event and .notify_phy_event
callbacks.
These callbacks are fixed and so there is no reason why the functions
cannot be called directly, so do that.
This neatens the code slightly, makes it more obvious, and reduces function
pointer usage, which is generally a good thing. Downside is that there are
2x more symbol exports.
[a.darwish@linutronix.de: Remove the now unused "sas_ha" local variables]
Link: https://lore.kernel.org/r/20210118100955.1761652-3-a.darwish@linutronix.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull in the 5.11 SCSI fixes branch to provide an updated baseline for
megaraid and hisi_sas. Both drivers received core changes in
v5.11-rc3.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge two commits that had dependencies on other 5.11 trees (the block
and the irq trees respectively).
- We reverted a megaraid_sas change in 5.10 due to missing block
layer plumbing. Now that this is in place, reinstate the change.
- The hisi_sas driver had a dependency on a driver core irq change
that went in through Thomas' tree.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
As a performance enhancement, make the completion queue interrupts managed.
In addition, in commit bf0beec060 ("blk-mq: drain I/O when all CPUs in a
hctx are offline"), CPU hotplug for MQ devices using managed interrupts is
made safe. So expose HW queues to blk-mq to take advantage of this.
Flag Scsi_host.host_tagset is also set to ensure that the HBA is not sent
more commands than it can handle. However the driver still does not use
request tag for IPTT as there are many HW bugs means that special rules
apply for IPTT allocation.
Link: https://lore.kernel.org/r/1606905417-183214-6-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, qla2xxx,
smartpqi, target, zfcp, fnic, mpt3sas, ibmvfc) plus a load of
cleanups, a major power management rework and a load of assorted minor
updates. There are a few core updates (formatting fixes being the big
one) but nothing major this cycle.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX9o0KSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbOZAP9D5NTN
J7dJUo2MIMy84YBu+d9ag7yLlNiRWVY2yw5vHwD/Z7JjAVLwz/tzmyjU9//o2J6w
hwhOv6Uto89gLCWSEz8=
=KUPT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, qla2xxx, smartpqi,
target, zfcp, fnic, mpt3sas, ibmvfc) plus a load of cleanups, a major
power management rework and a load of assorted minor updates.
There are a few core updates (formatting fixes being the big one) but
nothing major this cycle"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: mpt3sas: Update driver version to 36.100.00.00
scsi: mpt3sas: Handle trigger page after firmware update
scsi: mpt3sas: Add persistent MPI trigger page
scsi: mpt3sas: Add persistent SCSI sense trigger page
scsi: mpt3sas: Add persistent Event trigger page
scsi: mpt3sas: Add persistent Master trigger page
scsi: mpt3sas: Add persistent trigger pages support
scsi: mpt3sas: Sync time periodically between driver and firmware
scsi: qla2xxx: Update version to 10.02.00.104-k
scsi: qla2xxx: Fix device loss on 4G and older HBAs
scsi: qla2xxx: If fcport is undergoing deletion complete I/O with retry
scsi: qla2xxx: Fix the call trace for flush workqueue
scsi: qla2xxx: Fix flash update in 28XX adapters on big endian machines
scsi: qla2xxx: Handle aborts correctly for port undergoing deletion
scsi: qla2xxx: Fix N2N and NVMe connect retry failure
scsi: qla2xxx: Fix FW initialization error on big endian machines
scsi: qla2xxx: Fix crash during driver load on big endian machines
scsi: qla2xxx: Fix compilation issue in PPC systems
scsi: qla2xxx: Don't check for fw_started while posting NVMe command
scsi: qla2xxx: Tear down session if FW say it is down
...
For when managed interrupts are used (and shost->nr_hw_queues is set), a
fixed queue - set per-device - is still used for internal I/Os.
If all the CPUs mapped to that queue are offlined, then the completions for
that queue are not serviced and any internal I/Os will time out.
Fix by selecting a queue for internal I/Os from the queue mapped from the
current CPU in this scenario.
This is still not ideal as it does not deal with CPU hotplug for inflight
internal I/Os, and needs proper support from [0].
[0] https://lore.kernel.org/linux-scsi/20200703130122.111448-1-hare@suse.de/T/#m7d77d049b18f33a24ef206af69ebb66d07440556
Link: https://lore.kernel.org/r/1607347855-59091-1-git-send-email-john.garry@huawei.com
Fixes: 8d98416a55 ("scsi: hisi_sas: Switch v3 hw to MQ")
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
hisi_sas_task_exec() uses preemptible() to see if it's safe to block. This
does not work for CONFIG_PREEMPT_COUNT=n kernels in which preemptible()
always returns 0.
The problem is masked when enabling some of the common Kconfig.debug
options (like CONFIG_DEBUG_ATOMIC_SLEEP), as they implicitly enable the
preemption counter.
In general, driver leaf functions should not make logic decisions based on
the context they're called from. The caller should be the entity
responsible for explicitly indicating context.
Since hisi_sas_task_exec() already has a gfp_t flags parameter, use it as
the explicit context marker.
Link: https://lore.kernel.org/r/20201126132952.2287996-3-bigeasy@linutronix.de
Fixes: 214e702d4b ("scsi: hisi_sas: Adjust task reject period during host reset")
Fixes: 550c0d89d5 ("scsi: hisi_sas: Replace in_softirq() check in hisi_sas_task_exec()")
Cc: Xiaofei Tan <tanxiaofei@huawei.com>
Cc: Xiang Chen <chenxiang66@hisilicon.com>
Cc: John Garry <john.garry@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate all the debugfs code for DFX to v3 hw since no other versions
support it.
Link: https://lore.kernel.org/r/1606207594-196362-4-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix some rollbacks in function hisi_sas_v3_probe() and
interrupt_init_v3_hw().
Link: https://lore.kernel.org/r/1606207594-196362-3-git-send-email-john.garry@huawei.com
Fixes: 8d98416a55 ("scsi: hisi_sas: Switch v3 hw to MQ")
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sometimes local functions are called indirectly from the hw driver, which
only makes the code harder to follow. Remove these.
Method .hw_init is only called from platform driver probe, which is not
relevant, so don't set this either.
Link: https://lore.kernel.org/r/1606207594-196362-2-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Both runtime_suspend_v3_hw() and runtime_resume_v3_hw() do nothing else but
invoke suspend_v3_hw() and resume_v3_hw() respectively. This is the case of
unnecessary function calls. To use those functions for runtime pm as well,
simply use UNIVERSAL_DEV_PM_OPS.
make -j$(nproc) W=1, with CONFIG_PM disabled, throws '-Wunused-function'
warning for runtime_suspend_v3_hw() and runtime_resume_v3_hw(). After
dropping those function definitions, the warning was thrown for
suspend_v3_hw() and resume_v3_hw(). Hence, mark them as '__maybe_unused'.
Link: https://lore.kernel.org/r/20201102164730.324035-15-vaibhavgupta40@gmail.com
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Drivers using new-framework/generic-framework should not handle standard
power management operations. These operations were performed by legacy
framework through PCI helper functions like pci_save/restore_state(),
pci_set_power_state(), etc.
Drivers should not use them now.
Link: https://lore.kernel.org/r/20201102164730.324035-14-vaibhavgupta40@gmail.com
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver calls pci_enable_wake(...., false) in hisi_sas_v3_resume(), and
there is no corresponding pci_enable_wake(...., true) in
hisi_sas_v3_suspend(). Either it should do enable-wake the device in
.suspend() or should not invoke pci_enable_wake() at all.
Concluding that this driver doesn't support enable-wake and PCI core calls
pci_enable_wake(pci_dev, PCI_D0, false) during resume, drop it from
hisi_sas_v3_resume().
Link: https://lore.kernel.org/r/20201102164730.324035-13-vaibhavgupta40@gmail.com
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In commit 8d98416a55 ("scsi: hisi_sas: Switch v3 hw to MQ"), the dispatch
function was changed to choose the delivery queue based on the request tag
HW queue index.
This heavily degrades performance for v2 hw, since the HW queues are not
exposed there, and, as such, HW queue #0 is used for every command.
Revert to previous behaviour for when nr_hw_queues is not set, that being
to choose the HW queue based on target device index.
Link: https://lore.kernel.org/r/1602750425-240341-1-git-send-email-john.garry@huawei.com
Fixes: 8d98416a55 ("scsi: hisi_sas: Switch v3 hw to MQ")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
ibmvfc, lpfc, smartpqi, hisi_sas, qedi, qedf, mpt3sas) and minor bug
fixes. There are only three core changes: adding sense codes,
cleaning up noretry and adding an option for limitless retries.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX4YulyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaZDAQCT7rwG
UEZYHgYkU9EX9ERVBQM0SW4mLrxf3g3P5ioJsAEAtkclCM4QsIOP+MIPjIa0EyUY
khu0kcrmeFR2YwA8zhw=
=4w4S
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"The usual driver updates (ufs, qla2xxx, tcmu, ibmvfc, lpfc, smartpqi,
hisi_sas, qedi, qedf, mpt3sas) and minor bug fixes.
There are only three core changes: adding sense codes, cleaning up
noretry and adding an option for limitless retries"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (226 commits)
scsi: hisi_sas: Recover PHY state according to the status before reset
scsi: hisi_sas: Filter out new PHY up events during suspend
scsi: hisi_sas: Add device link between SCSI devices and hisi_hba
scsi: hisi_sas: Add check for methods _PS0 and _PR0
scsi: hisi_sas: Add controller runtime PM support for v3 hw
scsi: hisi_sas: Switch to new framework to support suspend and resume
scsi: hisi_sas: Use hisi_hba->cq_nvecs for calling calling synchronize_irq()
scsi: qedf: Remove redundant assignment to variable 'rc'
scsi: lpfc: Remove unneeded variable 'status' in lpfc_fcp_cpu_map_store()
scsi: snic: Convert to use DEFINE_SEQ_ATTRIBUTE macro
scsi: qla4xxx: Delete unneeded variable 'status' in qla4xxx_process_ddb_changed
scsi: sun_esp: Use module_platform_driver to simplify the code
scsi: sun3x_esp: Use module_platform_driver to simplify the code
scsi: sni_53c710: Use module_platform_driver to simplify the code
scsi: qlogicpti: Use module_platform_driver to simplify the code
scsi: mac_esp: Use module_platform_driver to simplify the code
scsi: jazz_esp: Use module_platform_driver to simplify the code
scsi: mvumi: Fix error return in mvumi_io_attach()
scsi: lpfc: Drop nodelist reference on error in lpfc_gen_req()
scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()
...
Currently the PHY state is set according to the state of the PHYs after
reset. This is invalid as the PHYs are already re-initialized.
Set PHY state according to the state before the reset instead of after.
Link: https://lore.kernel.org/r/1601649038-25534-8-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently sas_resume_ha() is called while resuming the controller to wait
for all suspended PHYs to come up and all the libsas events to be
completed.
There is a scenario which will cause task hung: For direct attach with two
disks connected with two PHYs, disable phy0 before suspending the disk on
phy1 and the controller, then enable phy0 and resume the controller, and
task hung occurs as follows:
[ 591.901463] hisi_sas_v3_hw 0000:b4:02.0: resuming from operating state [D0]
[ 593.113525] hisi_sas_v3_hw 0000:b4:02.0: neither _PS0 nor _PR0 is defined
[ 593.120301] hisi_sas_v3_hw 0000:b4:02.0: waiting up to 25 seconds for 1 phy to resume
[ 593.120836] hisi_sas_v3_hw 0000:b4:02.0: phyup: phy0 link_rate=10(sata)
[ 593.134680] hisi_sas_v3_hw 0000:b4:02.0: phyup: phy1 link_rate=10(sata)
[ 593.134733] sas: phy-2:0 added to port-2:0, phy_mask:0x1 (5000000000000200)
[ 593.148350] sas: DOING DISCOVERY on port 0, pid:948
[ 593.153227] hisi_sas_v3_hw 0000:b4:02.0: dev[3:5] found
[ 593.159840] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 593.165663] sas: ata7: end_device-2:0: dev error handler
[ 593.165730] sas: ata2: end_device-2:1: dev error handler
[ 593.172532] hisi_sas_v3_hw 0000:b4:02.0: phydown: phy0 phy_state=0x2
[ 593.182570] hisi_sas_v3_hw 0000:b4:02.0: ignore flutter phy0 down
[ 593.331277] hisi_sas_v3_hw 0000:b4:02.0: phyup: phy0 link_rate=10(sata)
[ 593.498956] ata7.00: ATA-11: SAMSUNG MZ7LH960HAJR-00005, HXT7404Q, max UDMA/133
[ 593.506235] ata7.00: 1875385008 sectors, multi 16: LBA48 NCQ (depth 32)
[ 593.514295] ata7.00: configured for UDMA/133
[ 593.518557] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0 tries: 1
[ 593.528613] sas: ata7: end_device-2:0: model:SAMSUNG MZ7LH960HAJR-00005
serial:S45NNA0M712225
[ 593.537520] device_link_add 316: dev=2:0:2:0 supplier:2 consumer:0
[ 593.543674] device_link_add 324
[ 593.546801] device_link_add 352
[ 593.549930] device_link_add 406
[ 593.553058] device_link_add 440: dev=2:0:2:0 supplier:2 consumer:0
[ 593.559208] device_link_add 444
[ 593.562335] device_link_add 455
[ 593.565517] scsi 2:0:2:0: Direct-Access ATA SAMSUNG MZ7LH960 404Q PQ: 0
ANSI: 5
[ 620.057464] phy-2:1: resume timeout
[ 738.841445] INFO: task kworker/u256:0:8 blocked for more than 120 seconds.
[ 738.848295] Not tainted 5.8.0-rc1-76154-g0d52b59-dirty #744
[ 738.854361] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 738.862155] kworker/u256:0 D 0 8 2 0x00000028
[ 738.867626] Workqueue: 0000:b4:02.0_event_q sas_port_event_worker
[ 738.873693] Call trace:
[ 738.876133] __switch_to+0xf4/0x148
[ 738.879613] __schedule+0x270/0x5d8
[ 738.883091] schedule+0x78/0x110
[ 738.886307] schedule_timeout+0x1ac/0x280
[ 738.890299] wait_for_completion+0x94/0x138
[ 738.894472] flush_workqueue+0x114/0x438
[ 738.898377] sas_porte_bytes_dmaed+0x400/0x500
[ 738.902801] sas_port_event_worker+0x28/0x40
[ 738.907053] process_one_work+0x1e8/0x360
[ 738.911046] worker_thread+0x44/0x478
[ 738.914698] kthread+0x150/0x158
[ 738.917915] ret_from_fork+0x10/0x1c
[ 738.921534] INFO: task kworker/u256:1:948 blocked for more than 120 seconds.
[ 738.928550] Not tainted 5.8.0-rc1-76154-g0d52b59-dirty #744
[ 738.934614] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 738.942408] kworker/u256:1 D 0 948 2 0x00000028
[ 738.947873] Workqueue: 0000:b4:02.0_disco_q sas_discover_domain
[ 738.953766] Call trace:
[ 738.956203] __switch_to+0xf4/0x148
[ 738.959678] __schedule+0x270/0x5d8
[ 738.963152] schedule+0x78/0x110
[ 738.966368] rpm_resume+0xcc/0x550
[ 738.969757] __pm_runtime_resume+0x3c/0x88
[ 738.973836] rpm_get_suppliers+0x50/0x148
[ 738.977829] __pm_runtime_set_status+0x124/0x2f0
[ 738.982427] scsi_sysfs_add_sdev+0x1a0/0x2a8
[ 738.986679] scsi_probe_and_add_lun+0x888/0xab0
[ 738.991190] __scsi_scan_target+0xec/0x520
[ 738.995268] scsi_scan_target+0x11c/0x128
[ 738.999261] sas_rphy_add+0x15c/0x1e8
[ 739.002907] sas_probe_devices+0xe4/0x150
[ 739.006899] sas_discover_domain+0x33c/0x588
[ 739.011150] process_one_work+0x1e8/0x360
[ 739.015143] worker_thread+0x44/0x478
[ 739.018789] kthread+0x150/0x158
[ 739.022003] ret_from_fork+0x10/0x1c
...
If an extra phy0 up happens during resume of the SAS controller, it will
emit a new libsas event (event PORTE_BYTES_DMAED and event
DISCE_DISCOVER_DOMAIN). We will call function scsi_sysfs_add_sdev() in
event DISCE_DISCOVER_DOMAIN, which will call __pm_runtime_set_status() to
resume supplier (host controller). For runtime PM core, if device is in the
resuming state, the later resume request of the device will wait for
previous resume request to complete synchronously. At that point in time
the state of the controller is still resuming as it waits for all libsas
events to be completed, while libsas event DISCE_DISCOVER_DOMAIN is blocked
as the state of the controller is resuming which causes a deadlock.
To avoid the issue, filter out new PHY up events while the controller is
suspended.
Link: https://lore.kernel.org/r/1601649038-25534-7-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Runtime PM of SCSI devices is already supported in SCSI layer, we can
suspend/resume every SCSI device separately. But if there is no link
between hisi_hba and SCSI devices or SCSI targets it will cause issues if
the controller is suspended while SCSI devices are still resuming. Only
when all the SCSI devices under the controller are suspended, the
controller can be suspended. Add the device link between SCSI devices
and the controller.
Link: https://lore.kernel.org/r/1601649038-25534-6-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To support system suspend/resume or runtime suspend/resume, need to use the
function pci_set_power_state() to change the power state which requires at
least method _PS0 or _PR0 be filled by platform for v3 hw. So check whether
the method is supported, if not, print a warning.
A Kconfig dependency is added as there is no stub for
acpi_device_power_manageable().
Link: https://lore.kernel.org/r/1601649038-25534-5-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw we will add support for runtime PM which is only supported in new
framework. Legacy PM support and new framework are not allowed to be used
together. Switch to new framework to support suspend and resume.
Link: https://lore.kernel.org/r/1601649038-25534-3-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A call trace is observed when running function level reset with online CPUs
less than 16 and MSI auto-affinity enabled.
[16538.348038] Call trace:
[16538.348422] pci_irq_vector+0x98/0xc0
[16538.348947] disable_host_v3_hw+0x8c/0x288 [hisi_sas_v3_hw]
[16538.349706] hisi_sas_reset_prepare_v3_hw+0x60/0x88 [hisi_sas_v3_hw]
[16538.350631] pci_dev_save_and_disable+0x38/0x68
[16538.351290] pci_reset_function+0x44/0x88
[16538.351846] reset_store+0x6c/0xb8
[16538.352429] dev_attr_store+0x44/0x60
[16538.353035] sysfs_kf_write+0x58/0x80
[16538.353558] kernfs_fop_write+0x140/0x230
[16538.354175] __vfs_write+0x48/0x80
[16538.354675] vfs_write+0xb8/0x1d8
[16538.355145] ksys_write+0x74/0xf8
[16538.355615] __arm64_sys_write+0x24/0x30
[16538.356240] el0_svc_common.constprop.4+0x80/0x1f0
[16538.356905] do_el0_svc+0x2c/0x38
[16538.357408] el0_svc+0x14/0x40
[16538.357848] el0_sync_handler+0xbc/0x2ec
[16538.358388] el0_sync+0x140/0x180
The reason is that if we use pci_alloc_irq_vectors_affinity() to allocate
IRQs, the number of CQ IRQs can only be less than or equal to the number of
online CPUs, but we use hisi_hba->queue_count (always 16) to iterate during
interrupt_disable_v3_hw().
Use hisi_hba->cq_nvecs to replace hisi_hba->queue_count to avoid
synchronize IRQ on a CPU which does not exist.
Link: https://lore.kernel.org/r/1601649038-25534-2-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that the block layer provides a shared tag, we can switch the driver
to expose all HW queues.
Signed-off-by: John Garry <john.garry@huawei.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Through the new debugfs interface the user can select fixed code
patterns. Add two new interfaces fixed_code and fixed_code1.
Link: https://lore.kernel.org/r/1598958790-232272-7-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add BIST support for phy FFE (Feed forward equalizer) setting. The user can
configure FFE through the new debugfs interface.
FFE is a parameter used for link layer control. It will affect the link
quality between the SAS controller and the backplane. In the BIST test, the
FFE interface is provided to assist board testers in optimizing link
parameters.
The modification of the FFE parameter will affect the test after BIST or
the normal running of the board. The user should save the initial FFE
values and restore them after BIST test is complete.
Link: https://lore.kernel.org/r/1598958790-232272-6-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We use "phy_id" to identify phy in the BIST code but the rest of code
always uses "phy_no". Change it for consistency.
Link: https://lore.kernel.org/r/1598958790-232272-5-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When updating PROG_PHY_LINK_RATE to set linkrate for a phy we used a
hard-coded initial value instead of getting the current value from the
register. The assumption was that this register would not be modified, but
in fact it was partially modified in a new version of hardware. The
hard-coded value we used changed the default value of the register to a an
incorrect setting and as a result the SAS controller could not change
linkrate for the phy.
Delete hard-coded value and always read the latest value of register before
updating it.
Link: https://lore.kernel.org/r/1598958790-232272-4-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The macro for OOB phy linkrate is named CFG_PROG_PHY_LINK_RATE_* but that
is inaccurate. For clarification, include OOB in macro name.
Link: https://lore.kernel.org/r/1598958790-232272-3-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
hisi_sas_slot_task_free() attempts to dereference SSP task for non-ATA
tasks. If the task is SMP, the code may reference the wrong structure
although this may not cause any problems.
To avoid this, only access to SSP task when slot->n_elem_dif is not 0 which
indicates this is an SSP task.
Link: https://lore.kernel.org/r/1598958790-232272-2-git-send-email-john.garry@huawei.com
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (ufs, qla2xxx, tcmu,
lpfc, hpsa, zfcp, scsi_debug) and minor bug fixes. We also have a
huge docbook fix update like most other subsystems and no major update
to the core (the few non trivial updates are either minor fixes or
removing an unused feature [scsi_sdb_cache]).
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXyxq1yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSoAAQChZ4i8
ZqYW3pL33JO3fA8vdjvLuyC489Hj4wzIsl3/bQEAxYyM6BSLvMoLWR2Plq/JmTLm
4W/LDptarpTiDI3NuDc=
=4b0W
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, qla2xxx, tcmu, lpfc,
hpsa, zfcp, scsi_debug) and minor bug fixes.
We also have a huge docbook fix update like most other subsystems and
no major update to the core (the few non trivial updates are either
minor fixes or removing an unused feature [scsi_sdb_cache])"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (307 commits)
scsi: scsi_transport_srp: Sanitize scsi_target_block/unblock sequences
scsi: ufs-mediatek: Apply DELAY_AFTER_LPM quirk to Micron devices
scsi: ufs: Introduce device quirk "DELAY_AFTER_LPM"
scsi: virtio-scsi: Correctly handle the case where all LUNs are unplugged
scsi: scsi_debug: Implement tur_ms_to_ready parameter
scsi: scsi_debug: Fix request sense
scsi: lpfc: Fix typo in comment for ULP
scsi: ufs-mediatek: Prevent LPM operation on undeclared VCC
scsi: iscsi: Do not put host in iscsi_set_flashnode_param()
scsi: hpsa: Correct ctrl queue depth
scsi: target: tcmu: Make TMR notification optional
scsi: target: tcmu: Implement tmr_notify callback
scsi: target: tcmu: Fix and simplify timeout handling
scsi: target: tcmu: Factor out new helper ring_insert_padding
scsi: target: tcmu: Do not queue aborted commands
scsi: target: tcmu: Use priv pointer in se_cmd
scsi: target: Add tmr_notify backend function
scsi: target: Modify core_tmr_abort_task()
scsi: target: iscsi: Fix inconsistent debug message
scsi: target: iscsi: Fix login error when receiving
...
Abort failed commands in completion path. This avoids having to wait for
block layer timeouts and triggering the SCSI error handling thread.
Link: https://lore.kernel.org/r/1594627471-235395-2-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We need ata_scsi_dma_need_drain for all drivers wired up to drive ATAPI
devices through libata. That also includes the SAS HBA drivers in addition
to native libata HBA drivers.
Link: https://lore.kernel.org/r/20200615064624.37317-3-hch@lst.de
Fixes: cc97923a5b ("block: move dma drain handling to scsi")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This series consists of the usual driver updates (qla2xxx, ufs, zfcp,
target, scsi_debug, lpfc, qedi, qedf, hisi_sas, mpt3sas) plus a host
of other minor updates. There are no major core changes in this
series apart from a refactoring in scsi_lib.c.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXtq5QyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXyGAQCipTWx
7kHKHZBCVTU133bADt3+SstLrAm8PKZEXMnP9wEAzu4QkkW8URxEDRrpu7qk5gbA
9M/KyqvfRtTH7+BSK7M=
=J6aO
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
:This series consists of the usual driver updates (qla2xxx, ufs, zfcp,
target, scsi_debug, lpfc, qedi, qedf, hisi_sas, mpt3sas) plus a host
of other minor updates.
There are no major core changes in this series apart from a
refactoring in scsi_lib.c"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (207 commits)
scsi: ufs: ti-j721e-ufs: Fix unwinding of pm_runtime changes
scsi: cxgb3i: Fix some leaks in init_act_open()
scsi: ibmvscsi: Make some functions static
scsi: iscsi: Fix deadlock on recovery path during GFP_IO reclaim
scsi: ufs: Fix WriteBooster flush during runtime suspend
scsi: ufs: Fix index of attributes query for WriteBooster feature
scsi: ufs: Allow WriteBooster on UFS 2.2 devices
scsi: ufs: Remove unnecessary memset for dev_info
scsi: ufs-qcom: Fix scheduling while atomic issue
scsi: mpt3sas: Fix reply queue count in non RDPQ mode
scsi: lpfc: Fix lpfc_nodelist leak when processing unsolicited event
scsi: target: tcmu: Fix a use after free in tcmu_check_expired_queue_cmd()
scsi: vhost: Notify TCM about the maximum sg entries supported per command
scsi: qla2xxx: Remove return value from qla_nvme_ls()
scsi: qla2xxx: Remove an unused function
scsi: iscsi: Register sysfs for iscsi workqueue
scsi: scsi_debug: Parser tables and code interaction
scsi: core: Refactor scsi_mq_setup_tags function
scsi: core: Fix incorrect usage of shost_for_each_device
scsi: qla2xxx: Fix endianness annotations in source files
...
Register SAS_RAS_INTR0 can help us to figure out which ECC error has
occurred. This register is helpful to identify RAS issue, so we add it to
the list of debugfs register name list for easier retrieval.
Link: https://lore.kernel.org/r/1589552025-165012-4-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We found out that after phy up, the hardware reports another oob interrupt
but did not follow a phy up interrupt:
oob ready -> phy up -> DEV found -> oob read -> wait phy up -> timeout
We run link reset when wait phy up timeout, and it send a normal disk into
reset processing. So we made some circumvention action in the code, so that
this abnormal oob interrupt will not start the timer to wait for phy up.
Link: https://lore.kernel.org/r/1589552025-165012-2-git-send-email-john.garry@huawei.com
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The 'proc_name' entry in sysfs for hisi_sas is 'null' now because it is not
initialized in scsi_host_template. It looks like:
[root@localhost ~]# cat /sys/class/scsi_host/host2/proc_name
(null)
While the other driver's entry looks like:
linux-vnMQMU:~ # cat /sys/class/scsi_host/host0/proc_name
megaraid_sas
Link: https://lore.kernel.org/r/20200512113258.30781-1-yanaijie@huawei.com
Cc: John Garry <john.garry@huawei.com>
Cc: Xiang Chen <chenxiang66@hisilicon.com>
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
