[ Upstream commit ef88eefb1a ]
The RZ/G2L manual (chapter "IRQ Status Control Register (ISCR)") describes
the operation to clear interrupts through the ISCR register as follows:
[Write operation]
When "Falling-edge detection", "Rising-edge detection" or
"Falling/Rising-edge detection" is set in IITSR:
- In case ISTAT is 1
0: IRQn interrupt detection status is cleared.
1: Invalid to write.
- In case ISTAT is 0
Invalid to write.
When "Low-level detection" is set in IITSR.:
Invalid to write.
Take the interrupt type into account when clearing interrupts through the
ISCR register to avoid writing the ISCR when the interrupt type is level.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231120111820.87398-6-claudiu.beznea.uj@bp.renesas.com
Stable-dep-of: 9eec61df55 ("irqchip/renesas-rzg2l: Flush posted write in irq_eoi()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afc5aa46ed ]
The swiotlb does not support a mapping size > swiotlb_max_mapping_size().
On the other hand, with a 64KB PAGE_SIZE configuration, it's observed that
an NVME device can map a size between 300KB~512KB, which certainly failed
the swiotlb mappings, though the default pool of swiotlb has many slots:
systemd[1]: Started Journal Service.
=> nvme 0000:00:01.0: swiotlb buffer is full (sz: 327680 bytes), total 32768 (slots), used 32 (slots)
note: journal-offline[392] exited with irqs disabled
note: journal-offline[392] exited with preempt_count 1
Call trace:
[ 3.099918] swiotlb_tbl_map_single+0x214/0x240
[ 3.099921] iommu_dma_map_page+0x218/0x328
[ 3.099928] dma_map_page_attrs+0x2e8/0x3a0
[ 3.101985] nvme_prep_rq.part.0+0x408/0x878 [nvme]
[ 3.102308] nvme_queue_rqs+0xc0/0x300 [nvme]
[ 3.102313] blk_mq_flush_plug_list.part.0+0x57c/0x600
[ 3.102321] blk_add_rq_to_plug+0x180/0x2a0
[ 3.102323] blk_mq_submit_bio+0x4c8/0x6b8
[ 3.103463] __submit_bio+0x44/0x220
[ 3.103468] submit_bio_noacct_nocheck+0x2b8/0x360
[ 3.103470] submit_bio_noacct+0x180/0x6c8
[ 3.103471] submit_bio+0x34/0x130
[ 3.103473] ext4_bio_write_folio+0x5a4/0x8c8
[ 3.104766] mpage_submit_folio+0xa0/0x100
[ 3.104769] mpage_map_and_submit_buffers+0x1a4/0x400
[ 3.104771] ext4_do_writepages+0x6a0/0xd78
[ 3.105615] ext4_writepages+0x80/0x118
[ 3.105616] do_writepages+0x90/0x1e8
[ 3.105619] filemap_fdatawrite_wbc+0x94/0xe0
[ 3.105622] __filemap_fdatawrite_range+0x68/0xb8
[ 3.106656] file_write_and_wait_range+0x84/0x120
[ 3.106658] ext4_sync_file+0x7c/0x4c0
[ 3.106660] vfs_fsync_range+0x3c/0xa8
[ 3.106663] do_fsync+0x44/0xc0
Since untrusted devices might go down the swiotlb pathway with dma-iommu,
these devices should not map a size larger than swiotlb_max_mapping_size.
To fix this bug, add iommu_dma_max_mapping_size() for untrusted devices to
take into account swiotlb_max_mapping_size() v.s. iova_rcache_range() from
the iommu_dma_opt_mapping_size().
Fixes: 82612d66d5 ("iommu: Allow the dma-iommu api to use bounce buffers")
Link: https://lore.kernel.org/r/ee51a3a5c32cf885b18f6416171802669f4a718a.1707851466.git.nicolinc@nvidia.com
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
[will: Drop redundant is_swiotlb_active(dev) check]
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51b30ecb73 ]
Nicolin reports that swiotlb buffer allocations fail for an NVME device
behind an IOMMU using 64KiB pages. This is because we end up with a
minimum allocation alignment of 64KiB (for the IOMMU to map the buffer
safely) but a minimum DMA alignment mask corresponding to a 4KiB NVME
page (i.e. preserving the 4KiB page offset from the original allocation).
If the original address is not 4KiB-aligned, the allocation will fail
because swiotlb_search_pool_area() erroneously compares these unmasked
bits with the 64KiB-aligned candidate allocation.
Tweak swiotlb_search_pool_area() so that the DMA alignment mask is
reduced based on the required alignment of the allocation.
Fixes: 82612d66d5 ("iommu: Allow the dma-iommu api to use bounce buffers")
Link: https://lore.kernel.org/r/cover.1707851466.git.nicolinc@nvidia.com
Reported-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80fcac5538 ]
Patch series "minmax: Relax type checks in min() and max()", v4.
The min() (etc) functions in minmax.h require that the arguments have
exactly the same types.
However when the type check fails, rather than look at the types and fix
the type of a variable/constant, everyone seems to jump on min_t(). In
reality min_t() ought to be rare - when something unusual is being done,
not normality.
The orginal min() (added in 2.4.9) replaced several inline functions and
included the type - so matched the implicit casting of the function call.
This was renamed min_t() in 2.4.10 and the current min() added. There is
no actual indication that the conversion of negatve values to large
unsigned values has ever been an actual problem.
A quick grep shows 5734 min() and 4597 min_t(). Having the casts on
almost half of the calls shows that something is clearly wrong.
If the wrong type is picked (and it is far too easy to pick the type of
the result instead of the larger input) then significant bits can get
discarded.
Pretty much the worst example is in the derived clamp_val(), consider:
unsigned char x = 200u;
y = clamp_val(x, 10u, 300u);
I also suspect that many of the min_t(u16, ...) are actually wrong. For
example copy_data() in printk_ringbuffer.c contains:
data_size = min_t(u16, buf_size, len);
Here buf_size is 'unsigned int' and len 'u16', pass a 64k buffer (can you
prove that doesn't happen?) and no data is returned. Apparantly it did -
and has since been fixed.
The only reason that most of the min_t() are 'fine' is that pretty much
all the values in the kernel are between 0 and INT_MAX.
Patch 1 adds umin(), this uses integer promotions to convert both
arguments to 'unsigned long long'. It can be used to compare a signed
type that is known to contain a non-negative value with an unsigned type.
The compiler typically optimises it all away. Added first so that it can
be referred to in patch 2.
Patch 2 replaces the 'same type' check with a 'same signedness' one. This
makes min(unsigned_int_var, sizeof()) be ok. The error message is also
improved and will contain the expanded form of both arguments (useful for
seeing how constants are defined).
Patch 3 just fixes some whitespace.
Patch 4 allows comparisons of 'unsigned char' and 'unsigned short' to
signed types. The integer promotion rules convert them both to 'signed
int' prior to the comparison so they can never cause a negative value be
converted to a large positive one.
Patch 5 (rewritted for v4) allows comparisons of unsigned values against
non-negative constant integer expressions. This makes
min(unsigned_int_var, 4) be ok.
The only common case that is still errored is the comparison of signed
values against unsigned constant integer expressions below __INT_MAX__.
Typcally min(int_val, sizeof (foo)), the real fix for this is casting the
constant: min(int_var, (int)sizeof (foo)).
With all the patches applied pretty much all the min_t() could be replaced
by min(), and most of the rest by umin(). However they all need careful
inspection due to code like:
sz = min_t(unsigned char, sz - 1, LIM - 1) + 1;
which converts 0 to LIM.
This patch (of 6):
umin() and umax() can be used when min()/max() errors a signed v unsigned
compare when the signed value is known to be non-negative.
Unlike min_t(some_unsigned_type, a, b) umin() will never mask off high
bits if an inappropriate type is selected.
The '+ 0u + 0ul + 0ull' may look strange.
The '+ 0u' is needed for 'signed int' on 64bit systems.
The '+ 0ul' is needed for 'signed long' on 32bit systems.
The '+ 0ull' is needed for 'signed long long'.
Link: https://lkml.kernel.org/r/b97faef60ad24922b530241c5d7c933c@AcuMS.aculab.com
Link: https://lkml.kernel.org/r/41d93ca827a248698ec64bf57e0c05a5@AcuMS.aculab.com
Signed-off-by: David Laight <david.laight@aculab.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 51b30ecb73 ("swiotlb: Fix alignment checks when both allocation and DMA masks are present")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb13b11d53 ]
When a probe is registered at the trace_sys_enter() tracepoint, and that
probe changes the system call number, the old system call still gets
executed. This worked correctly until commit b6ec413461 ("core/entry:
Report syscall correctly for trace and audit"), which removed the
re-evaluation of the syscall number after the trace point.
Restore the original semantics by re-evaluating the system call number
after trace_sys_enter().
The performance impact of this re-evaluation is minimal because it only
takes place when a trace point is active, and compared to the actual trace
point overhead the read from a cache hot variable is negligible.
Fixes: b6ec413461 ("core/entry: Report syscall correctly for trace and audit")
Signed-off-by: André Rösti <an.roesti@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240311211704.7262-1-an.roesti@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b34b9547ce ]
The prescaler in the "Global Timer Control Register bit assignments" is
documented to use bits [15:8], which means that the maximum prescaler
register value is 0xff.
Fixes: 171b45a4a7 ("clocksource/drivers/arm_global_timer: Implement rate compensation whenever source clock changes")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240218174138.1942418-2-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
This fix is applicable for LTS kernel, 6.1.y. In latest kernels, this race
issue is fixed by the patch series [1] and [2]. The right thing to do here
would have been propagating these changes from latest kernel to the stable
branch, 6.1.y. However, these changes seems too intrusive to be picked for
stable branches. Hence, the fix proposed can be taken as an alternative
instead of backporting the patch series.
[1] https://lore.kernel.org/all/0-v8-81230027b2fa+9d-iommu_all_defdom_jgg@nvidia.com/
[2] https://lore.kernel.org/all/0-v5-1b99ae392328+44574-iommu_err_unwind_jgg@nvidia.com/
Issue:
A race condition is observed when arm_smmu_device_probe and
modprobe of client devices happens in parallel. This results
in the allocation of a new default domain for the iommu group
even though it was previously allocated and the respective iova
domain(iovad) was initialized. However, for this newly allocated
default domain, iovad will not be initialized. As a result, for
devices requesting dma allocations, this uninitialized iovad will
be used, thereby causing NULL pointer dereference issue.
Flow:
- During arm_smmu_device_probe, bus_iommu_probe() will be called
as part of iommu_device_register(). This results in the device probe,
__iommu_probe_device().
- When the modprobe of the client device happens in parallel, it
sets up the DMA configuration for the device using of_dma_configure_id(),
which inturn calls iommu_probe_device(). Later, default domain is
allocated and attached using iommu_alloc_default_domain() and
__iommu_attach_device() respectively. It then ends up initializing a
mapping domain(IOVA domain) and rcaches for the device via
arch_setup_dma_ops()->iommu_setup_dma_ops().
- Now, in the bus_iommu_probe() path, it again tries to allocate
a default domain via probe_alloc_default_domain(). This results in
allocating a new default domain(along with IOVA domain) via
__iommu_domain_alloc(). However, this newly allocated IOVA domain
will not be initialized.
- Now, when the same client device tries dma allocations via
iommu_dma_alloc(), it ends up accessing the rcaches of the newly
allocated IOVA domain, which is not initialized. This results
into NULL pointer dereferencing.
Fix this issue by adding a check in probe_alloc_default_domain()
to see if the iommu_group already has a default domain allocated
and initialized.
Cc: <stable@vger.kernel.org> # see patch description, fix applicable only for 6.1.y
Signed-off-by: Charan Teja Kalla <quic_charante@quicinc.com>
Co-developed-by: Nikhil V <quic_nprakash@quicinc.com>
Signed-off-by: Nikhil V <quic_nprakash@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 861b3415e4 upstream.
This reverts commit ed00a6945d,
which added a quirk entry to enable the Yellow Carp (YC)
driver for the Lenovo 21J2 laptop.
Although the microphone functioned with the YC driver, it
resulted in incorrect driver usage. The Lenovo 21J2 is not a
Yellow Carp platform, but a Pink Sardine platform, which
already has an upstreamed driver.
The microphone on the Lenovo 21J2 operates correctly with the
CONFIG_SND_SOC_AMD_PS flag enabled and does not require the
quirk entry. So this patch removes the quirk entry.
Thanks to Mukunda Vijendar [1] for pointing this out.
Link: https://lore.kernel.org/linux-sound/023092e1-689c-4b00-b93f-4092c3724fb6@amd.com/ [1]
Signed-off-by: Jiawei Wang <me@jwang.link>
Link: https://lore.kernel.org/linux-sound/023092e1-689c-4b00-b93f-4092c3724fb6@amd.com/ [1]
Link: https://msgid.link/r/20240313015853.3573242-2-me@jwang.link
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Luca Stefani <luca.stefani.ge1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8590541473 upstream.
Since we're setting the CRYPTO_TFM_REQ_MAY_BACKLOG flag on our
requests to the crypto API, crypto_aead_{encrypt,decrypt} can return
-EBUSY instead of -EINPROGRESS in valid situations. For example, when
the cryptd queue for AESNI is full (easy to trigger with an
artificially low cryptd.cryptd_max_cpu_qlen), requests will be enqueued
to the backlog but still processed. In that case, the async callback
will also be called twice: first with err == -EINPROGRESS, which it
seems we can just ignore, then with err == 0.
Compared to Sabrina's original patch this version uses the new
tls_*crypt_async_wait() helpers and converts the EBUSY to
EINPROGRESS to avoid having to modify all the error handling
paths. The handling is identical.
Fixes: a54667f672 ("tls: Add support for encryption using async offload accelerator")
Fixes: 94524d8fc9 ("net/tls: Add support for async decryption of tls records")
Co-developed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/netdev/9681d1febfec295449a62300938ed2ae66983f28.1694018970.git.sd@queasysnail.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Srish: v2: fixed hunk failures
fixed merge-conflict in stable branch linux-6.1.y,
needs to go on top of https://lore.kernel.org/stable/20240307155930.913525-1-lee@kernel.org/]
Signed-off-by: Srish Srinivasan <srish.srinivasan@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cefcd4fe2e upstream.
Normally, the EFI stub calls into the EFI boot services using the stack
that was live when the stub was entered. According to the UEFI spec,
this stack needs to be at least 128k in size - this might seem large but
all asynchronous processing and event handling in EFI runs from the same
stack and so quite a lot of space may be used in practice.
In mixed mode, the situation is a bit different: the bootloader calls
the 32-bit EFI stub entry point, which calls the decompressor's 32-bit
entry point, where the boot stack is set up, using a fixed allocation
of 16k. This stack is still in use when the EFI stub is started in
64-bit mode, and so all calls back into the EFI firmware will be using
the decompressor's limited boot stack.
Due to the placement of the boot stack right after the boot heap, any
stack overruns have gone unnoticed. However, commit
5c4feadb00 ("x86/decompressor: Move global symbol references to C code")
moved the definition of the boot heap into C code, and now the boot
stack is placed right at the base of BSS, where any overruns will
corrupt the end of the .data section.
While it would be possible to work around this by increasing the size of
the boot stack, doing so would affect all x86 systems, and mixed mode
systems are a tiny (and shrinking) fraction of the x86 installed base.
So instead, record the firmware stack pointer value when entering from
the 32-bit firmware, and switch to this stack every time a EFI boot
service call is made.
Cc: <stable@kernel.org> # v6.1+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 937844d661 upstream.
Need to check the offset bits for values greater than 255.
v2: also update amdgpu_dm_connector values.
Suggested-by: Mano Ségransan <mano.segransan@protonmail.com>
Tested-by: Mano Ségransan <mano.segransan@protonmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3203
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ceb013b2d9 upstream.
If registering the platform device fails, the lookup table is
removed in the error path. On module removal we would try to
remove the lookup table again. Fix this by setting priv->lookup
only if registering the platform device was successful.
In addition free the memory allocated for the lookup table in
the error path.
Fixes: d308dfbf62 ("i2c: mux/i801: Switch to use descriptor passing")
Cc: stable@vger.kernel.org
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 11dadb6310 upstream.
As specified in the datasheet, the I2C FIFO data register is
0x18, not 0x42. 0x42 was used by mistake when adapting the
ADXL372 driver.
Fix this mistake.
Fixes: cbab791c5e ("iio: accel: add ADXL367 driver")
Signed-off-by: Cosmin Tanislav <demonsingur@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240207033657.206171-2-demonsingur@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b926914bb upstream.
regmap_read_poll_timeout() will not sleep before reading,
causing the first read to return -ENXIO on I2C, since the
chip does not respond to it while it is being reset.
The datasheet specifies that a soft reset operation has a
latency of 7.5ms.
Add a 15ms sleep between reset and reading the DEVID register,
and switch to a simple regmap_read() call.
Fixes: cbab791c5e ("iio: accel: add ADXL367 driver")
Signed-off-by: Cosmin Tanislav <demonsingur@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240207033657.206171-1-demonsingur@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 803de9000f upstream.
Sven reports an infinite loop in __alloc_pages_slowpath() for costly order
__GFP_RETRY_MAYFAIL allocations that are also GFP_NOIO. Such combination
can happen in a suspend/resume context where a GFP_KERNEL allocation can
have __GFP_IO masked out via gfp_allowed_mask.
Quoting Sven:
1. try to do a "costly" allocation (order > PAGE_ALLOC_COSTLY_ORDER)
with __GFP_RETRY_MAYFAIL set.
2. page alloc's __alloc_pages_slowpath tries to get a page from the
freelist. This fails because there is nothing free of that costly
order.
3. page alloc tries to reclaim by calling __alloc_pages_direct_reclaim,
which bails out because a zone is ready to be compacted; it pretends
to have made a single page of progress.
4. page alloc tries to compact, but this always bails out early because
__GFP_IO is not set (it's not passed by the snd allocator, and even
if it were, we are suspending so the __GFP_IO flag would be cleared
anyway).
5. page alloc believes reclaim progress was made (because of the
pretense in item 3) and so it checks whether it should retry
compaction. The compaction retry logic thinks it should try again,
because:
a) reclaim is needed because of the early bail-out in item 4
b) a zonelist is suitable for compaction
6. goto 2. indefinite stall.
(end quote)
The immediate root cause is confusing the COMPACT_SKIPPED returned from
__alloc_pages_direct_compact() (step 4) due to lack of __GFP_IO to be
indicating a lack of order-0 pages, and in step 5 evaluating that in
should_compact_retry() as a reason to retry, before incrementing and
limiting the number of retries. There are however other places that
wrongly assume that compaction can happen while we lack __GFP_IO.
To fix this, introduce gfp_compaction_allowed() to abstract the __GFP_IO
evaluation and switch the open-coded test in try_to_compact_pages() to use
it.
Also use the new helper in:
- compaction_ready(), which will make reclaim not bail out in step 3, so
there's at least one attempt to actually reclaim, even if chances are
small for a costly order
- in_reclaim_compaction() which will make should_continue_reclaim()
return false and we don't over-reclaim unnecessarily
- in __alloc_pages_slowpath() to set a local variable can_compact,
which is then used to avoid retrying reclaim/compaction for costly
allocations (step 5) if we can't compact and also to skip the early
compaction attempt that we do in some cases
Link: https://lkml.kernel.org/r/20240221114357.13655-2-vbabka@suse.cz
Fixes: 3250845d05 ("Revert "mm, oom: prevent premature OOM killer invocation for high order request"")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Sven van Ashbrook <svenva@chromium.org>
Closes: https://lore.kernel.org/all/CAG-rBihs_xMKb3wrMO1%2B-%2Bp4fowP9oy1pa_OTkfxBzPUVOZF%2Bg@mail.gmail.com/
Tested-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Cc: Brian Geffon <bgeffon@google.com>
Cc: Curtis Malainey <cujomalainey@chromium.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a17bd44c01 upstream.
The HP EliteBook using ALC236 codec which using 0x02 to
control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240304134033.773348-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34ab5bbc6e upstream.
It will be enable headset Mic for Acer NB platform.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/fe0eb6661ca240f3b7762b5b3257710d@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 961ebd1205 upstream.
The first kiocb_set_cancel_fn() argument may point at a struct kiocb
that is not embedded inside struct aio_kiocb. With the current code,
depending on the compiler, the req->ki_ctx read happens either before
the IOCB_AIO_RW test or after that test. Move the req->ki_ctx read such
that it is guaranteed that the IOCB_AIO_RW test happens first.
Reported-by: Eric Biggers <ebiggers@kernel.org>
Cc: Benjamin LaHaise <ben@communityfibre.ca>
Cc: Eric Biggers <ebiggers@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Sandeep Dhavale <dhavale@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: stable@vger.kernel.org
Fixes: b820de741a ("fs/aio: Restrict kiocb_set_cancel_fn() to I/O submitted via libaio")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240304235715.3790858-1-bvanassche@acm.org
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1581dafaf0 upstream.
This is the same issue that was fixed for the VGA text buffer in commit
39cdb68c64 ("vt: fix memory overlapping when deleting chars in the
buffer"). The cure is also the same i.e. replace memcpy() with memmove()
due to the overlaping buffers.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Fixes: 81732c3b2f ("tty vt: Fix line garbage in virtual console on command line edition")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/sn184on2-3p0q-0qrq-0218-895349s4753o@syhkavp.arg
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac3e038407 upstream.
When not configured for wakeup lis3lv02d_i2c_suspend() will call
lis3lv02d_poweroff() even if the device has already been turned off
by the runtime-suspend handler and if configured for wakeup and
the device is runtime-suspended at this point then it is not turned
back on to serve as a wakeup source.
Before commit b1b9f7a494 ("misc: lis3lv02d_i2c: Add missing setting
of the reg_ctrl callback"), lis3lv02d_poweroff() failed to disable
the regulators which as a side effect made calling poweroff() twice ok.
Now that poweroff() correctly disables the regulators, doing this twice
triggers a WARN() in the regulator core:
unbalanced disables for regulator-dummy
WARNING: CPU: 1 PID: 92 at drivers/regulator/core.c:2999 _regulator_disable
...
Fix lis3lv02d_i2c_suspend() to not call poweroff() a second time if
already runtime-suspended and add a poweron() call when necessary to
make wakeup work.
lis3lv02d_i2c_resume() has similar issues, with an added weirness that
it always powers on the device if it is runtime suspended, after which
the first runtime-resume will call poweron() again, causing the enabled
count for the regulator to increase by 1 every suspend/resume. These
unbalanced regulator_enable() calls cause the regulator to never
be turned off and trigger the following WARN() on driver unbind:
WARNING: CPU: 1 PID: 1724 at drivers/regulator/core.c:2396 _regulator_put
Fix this by making lis3lv02d_i2c_resume() mirror the new suspend().
Fixes: b1b9f7a494 ("misc: lis3lv02d_i2c: Add missing setting of the reg_ctrl callback")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://lore.kernel.org/regressions/5fc6da74-af0a-4aac-b4d5-a000b39a63a5@molgen.mpg.de/
Cc: stable@vger.kernel.org
Cc: regressions@lists.linux.dev
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> # Dell XPS 15 7590
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/20240220190035.53402-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74cb7e0355 upstream.
If the remote uart device is not connected or not enabled after booting
up, the CTS line is high by default. At this time, if we enable the flow
control when opening the device(for example, using “stty -F /dev/ttyLP4
crtscts” command), there will be a pending idle preamble(first writing 0
and then writing 1 to UARTCTRL_TE will queue an idle preamble) that
cannot be sent out, resulting in the uart port fail to close(waiting for
TX empty), so the user space stty will have to wait for a long time or
forever.
This is an LPUART IP bug(idle preamble has higher priority than CTS),
here add a workaround patch to enable TX CTS after enabling UARTCTRL_TE,
so that the idle preamble does not get stuck due to CTS is deasserted.
Fixes: 380c966c09 ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20240305015706.1050769-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f90ce1e04c upstream.
While connecting to a Linux host with CDC_NCM_NTB_DEF_SIZE_TX
set to 65536, it has been observed that we receive short packets,
which come at interval of 5-10 seconds sometimes and have block
length zero but still contain 1-2 valid datagrams present.
According to the NCM spec:
"If wBlockLength = 0x0000, the block is terminated by a
short packet. In this case, the USB transfer must still
be shorter than dwNtbInMaxSize or dwNtbOutMaxSize. If
exactly dwNtbInMaxSize or dwNtbOutMaxSize bytes are sent,
and the size is a multiple of wMaxPacketSize for the
given pipe, then no ZLP shall be sent.
wBlockLength= 0x0000 must be used with extreme care, because
of the possibility that the host and device may get out of
sync, and because of test issues.
wBlockLength = 0x0000 allows the sender to reduce latency by
starting to send a very large NTB, and then shortening it when
the sender discovers that there’s not sufficient data to justify
sending a large NTB"
However, there is a potential issue with the current implementation,
as it checks for the occurrence of multiple NTBs in a single
giveback by verifying if the leftover bytes to be processed is zero
or not. If the block length reads zero, we would process the same
NTB infintely because the leftover bytes is never zero and it leads
to a crash. Fix this by bailing out if block length reads zero.
Cc: stable@vger.kernel.org
Fixes: 427694cfaa ("usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240228115441.2105585-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 014bcf41d9 upstream.
The isd200 sub-driver in usb-storage uses the HEADS and SECTORS values
in the ATA ID information to calculate cylinder and head values when
creating a CDB for READ or WRITE commands. The calculation involves
division and modulus operations, which will cause a crash if either of
these values is 0. While this never happens with a genuine device, it
could happen with a flawed or subversive emulation, as reported by the
syzbot fuzzer.
Protect against this possibility by refusing to bind to the device if
either the ATA_ID_HEADS or ATA_ID_SECTORS value in the device's ID
information is 0. This requires isd200_Initialization() to return a
negative error code when initialization fails; currently it always
returns 0 (even when there is an error).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+28748250ab47a8f04100@syzkaller.appspotmail.com
Link: https://lore.kernel.org/linux-usb/0000000000003eb868061245ba7f@google.com/
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/b1e605ea-333f-4ac0-9511-da04f411763e@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d397b6e561 upstream.
Headset Mic will no show at resume back.
This patch will fix this issue.
Fixes: d7f32791a9 ("ALSA: hda/realtek - Add headset Mic support for Lenovo ALC897 platform")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/4713d48a372e47f98bba0c6120fd8254@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01bb1ae350 upstream.
Error in mmu_interval_notifier_insert() can leave a NULL
notifier.mm pointer. Catch that and return early.
Fixes: ed29c26911 ("drm/i915: Fix userptr so we do not have to worry about obj->mm.lock, v7.")
Cc: <stable@vger.kernel.org> # v5.13+
[tursulin: Added Fixes and cc stable.]
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Shawn Lee <shawn.c.lee@intel.com>
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240219125047.28906-1-nirmoy.das@intel.com
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
(cherry picked from commit db7bbd13f0)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0dafaf659c upstream.
Fix the pwm_mode value error which used for
pwm1_enable setting
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5d7c19165 upstream.
The .release() function does not get called until all readers of a file
descriptor are finished.
If a thread is blocked on reading a file descriptor in ring_buffer_wait(),
and another thread closes the file descriptor, it will not wake up the
other thread as ring_buffer_wake_waiters() is called by .release(), and
that will not get called until the .read() is finished.
The issue originally showed up in trace-cmd, but the readers are actually
other processes with their own file descriptors. So calling close() would wake
up the other tasks because they are blocked on another descriptor then the
one that was closed(). But there's other wake ups that solve that issue.
When a thread is blocked on a read, it can still hang even when another
thread closed its descriptor.
This is what the .flush() callback is for. Have the .flush() wake up the
readers.
Link: https://lore.kernel.org/linux-trace-kernel/20240308202432.107909457@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linke li <lilinke99@qq.com>
Cc: Rabin Vincent <rabin@rab.in>
Fixes: f3ddb74ad0 ("tracing: Wake up ring buffer waiters on closing of the file")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ef1d8c1dd upstream.
Do the cache flush of converted pages in svm_register_enc_region() before
dropping kvm->lock to fix use-after-free issues where region and/or its
array of pages could be freed by a different task, e.g. if userspace has
__unregister_enc_region_locked() already queued up for the region.
Note, the "obvious" alternative of using local variables doesn't fully
resolve the bug, as region->pages is also dynamically allocated. I.e. the
region structure itself would be fine, but region->pages could be freed.
Flushing multiple pages under kvm->lock is unfortunate, but the entire
flow is a rare slow path, and the manual flush is only needed on CPUs that
lack coherency for encrypted memory.
Fixes: 19a23da539 ("Fix unsynchronized access to sev members through svm_register_enc_region")
Reported-by: Gabe Kirkpatrick <gkirkpatrick@google.com>
Cc: Josh Eads <josheads@google.com>
Cc: Peter Gonda <pgonda@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20240217013430.2079561-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 910c57dfa4 upstream.
When emulating an atomic access on behalf of the guest, mark the target
gfn dirty if the CMPXCHG by KVM is attempted and doesn't fault. This
fixes a bug where KVM effectively corrupts guest memory during live
migration by writing to guest memory without informing userspace that the
page is dirty.
Marking the page dirty got unintentionally dropped when KVM's emulated
CMPXCHG was converted to do a user access. Before that, KVM explicitly
mapped the guest page into kernel memory, and marked the page dirty during
the unmap phase.
Mark the page dirty even if the CMPXCHG fails, as the old data is written
back on failure, i.e. the page is still written. The value written is
guaranteed to be the same because the operation is atomic, but KVM's ABI
is that all writes are dirty logged regardless of the value written. And
more importantly, that's what KVM did before the buggy commit.
Huge kudos to the folks on the Cc list (and many others), who did all the
actual work of triaging and debugging.
Fixes: 1c2361f667 ("KVM: x86: Use __try_cmpxchg_user() to emulate atomic accesses")
Cc: stable@vger.kernel.org
Cc: David Matlack <dmatlack@google.com>
Cc: Pasha Tatashin <tatashin@google.com>
Cc: Michael Krebs <mkrebs@google.com>
base-commit: 6769ea8da8a93ed4630f1ce64df6aafcaabfce64
Reviewed-by: Jim Mattson <jmattson@google.com>
Link: https://lore.kernel.org/r/20240215010004.1456078-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e00f5802f upstream.
We continue to see false positives from -Warray-bounds even in GCC 10,
which is getting reported in a few places[1] still:
security/security.c:811:2: warning: `memcpy' offset 32 is out of the bounds [0, 0] [-Warray-bounds]
Lower the GCC version check from 11 to 10.
Link: https://lkml.kernel.org/r/20240223170824.work.768-kees@kernel.org
Reported-by: Lu Yao <yaolu@kylinos.cn>
Closes: https://lore.kernel.org/lkml/20240117014541.8887-1-yaolu@kylinos.cn/
Link: https://lore.kernel.org/linux-next/65d84438.620a0220.7d171.81a7@mx.google.com [1]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Marc Aurèle La France <tsi@tuyoix.net>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a807e46aa upstream.
After a couple recent changes in LLVM, there is a warning (or error with
CONFIG_WERROR=y or W=e) from the compile time fortify source routines,
specifically the memset() in copy_to_user_tmpl().
In file included from net/xfrm/xfrm_user.c:14:
...
include/linux/fortify-string.h:438:4: error: call to '__write_overflow_field' declared with 'warning' attribute: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror,-Wattribute-warning]
438 | __write_overflow_field(p_size_field, size);
| ^
1 error generated.
While ->xfrm_nr has been validated against XFRM_MAX_DEPTH when its value
is first assigned in copy_templates() by calling validate_tmpl() first
(so there should not be any issue in practice), LLVM/clang cannot really
deduce that across the boundaries of these functions. Without that
knowledge, it cannot assume that the loop stops before i is greater than
XFRM_MAX_DEPTH, which would indeed result a stack buffer overflow in the
memset().
To make the bounds of ->xfrm_nr clear to the compiler and add additional
defense in case copy_to_user_tmpl() is ever used in a path where
->xfrm_nr has not been properly validated against XFRM_MAX_DEPTH first,
add an explicit bound check and early return, which clears up the
warning.
Cc: stable@vger.kernel.org
Link: https://github.com/ClangBuiltLinux/linux/issues/1985
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b820954429 upstream.
The VMBUS_RING_SIZE macro adds space for a ring buffer header to the
requested ring buffer size. The header size is always 1 page, and so
its size varies based on the PAGE_SIZE for which the kernel is built.
If the requested ring buffer size is a large power-of-2 size and the header
size is small, the resulting size is inefficient in its use of memory.
For example, a 512 Kbyte ring buffer with a 4 Kbyte page size results in
a 516 Kbyte allocation, which is rounded to up 1 Mbyte by the memory
allocator, and wastes 508 Kbytes of memory.
In such situations, the exact size of the ring buffer isn't that important,
and it's OK to allocate the 4 Kbyte header at the beginning of the 512
Kbytes, leaving the ring buffer itself with just 508 Kbytes. The memory
allocation can be 512 Kbytes instead of 1 Mbyte and nothing is wasted.
Update VMBUS_RING_SIZE to implement this approach for "large" ring buffer
sizes. "Large" is somewhat arbitrarily defined as 8 times the size of
the ring buffer header (which is of size PAGE_SIZE). For example, for
4 Kbyte PAGE_SIZE, ring buffers of 32 Kbytes and larger use the first
4 Kbytes as the ring buffer header. For 64 Kbyte PAGE_SIZE, ring buffers
of 512 Kbytes and larger use the first 64 Kbytes as the ring buffer
header. In both cases, smaller sizes add space for the header so
the ring size isn't reduced too much by using part of the space for
the header. For example, with a 64 Kbyte page size, we don't want
a 128 Kbyte ring buffer to be reduced to 64 Kbytes by allocating half
of the space for the header. In such a case, the memory allocation
is less efficient, but it's the best that can be done.
While the new algorithm slightly changes the amount of space allocated
for ring buffers by drivers that use VMBUS_RING_SIZE, the devices aren't
known to be sensitive to small changes in ring buffer size, so there
shouldn't be any effect.
Fixes: c1135c7fd0 ("Drivers: hv: vmbus: Introduce types of GPADL")
Fixes: 6941f67ad3 ("hv_netvsc: Calculate correct ring size when PAGE_SIZE is not 4 Kbytes")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218502
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Tested-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Link: https://lore.kernel.org/r/20240229004533.313662-1-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240229004533.313662-1-mhklinux@outlook.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f4fc4bd5c upstream.
This set combination is weird: it allows for elements to be
added/deleted, but once bound to the rule it cannot be updated anymore.
Eventually, all elements expire, leading to an empty set which cannot
be updated anymore. Reject this flags combination.
Cc: stable@vger.kernel.org
Fixes: 761da2935d ("netfilter: nf_tables: add set timeout API support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16603605b6 upstream.
Anonymous sets are never used with timeout from userspace, reject this.
Exception to this rule is NFT_SET_EVAL to ensure legacy meters still work.
Cc: stable@vger.kernel.org
Fixes: 761da2935d ("netfilter: nf_tables: add set timeout API support")
Reported-by: lonial con <kongln9170@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 552705a365 upstream.
While the rhashtable set gc runs asynchronously, a race allows it to
collect elements from anonymous sets with timeouts while it is being
released from the commit path.
Mingi Cho originally reported this issue in a different path in 6.1.x
with a pipapo set with low timeouts which is not possible upstream since
7395dfacff ("netfilter: nf_tables: use timestamp to check for set
element timeout").
Fix this by setting on the dead flag for anonymous sets to skip async gc
in this case.
According to 08e4c8c591 ("netfilter: nf_tables: mark newset as dead on
transaction abort"), Florian plans to accelerate abort path by releasing
objects via workqueue, therefore, this sets on the dead flag for abort
path too.
Cc: stable@vger.kernel.org
Fixes: 5f68718b34 ("netfilter: nf_tables: GC transaction API to avoid race with control plane")
Reported-by: Mingi Cho <mgcho.minic@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e01e3934a1 upstream.
Similarly to previous commit, the submitting thread (recvmsg/sendmsg)
may exit as soon as the async crypto handler calls complete().
Reorder scheduling the work before calling complete().
This seems more logical in the first place, as it's
the inverse order of what the submitting thread will do.
Reported-by: valis <sec@valis.email>
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Lee: Fixed merge-conflict in Stable branches linux-6.1.y and older]
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aec7d25b49 upstream.
On Goldmont p2sb_bar() only ever gets called for 2 devices, the actual P2SB
devfn 13,0 and the SPI controller which is part of the P2SB, devfn 13,2.
But the current p2sb code tries to cache BAR0 info for all of
devfn 13,0 to 13,7 . This involves calling pci_scan_single_device()
for device 13 functions 0-7 and the hw does not seem to like
pci_scan_single_device() getting called for some of the other hidden
devices. E.g. on an ASUS VivoBook D540NV-GQ065T this leads to continuous
ACPI errors leading to high CPU usage.
Fix this by only caching BAR0 info and thus only calling
pci_scan_single_device() for the P2SB and the SPI controller.
Fixes: 5913320eb0 ("platform/x86: p2sb: Allow p2sb_bar() calls during PCI device probe")
Reported-by: Danil Rybakov <danilrybakov249@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218531
Tested-by: Danil Rybakov <danilrybakov249@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240304134356.305375-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3f269ed0a ]
Since:
7ee18d6779 ("x86/power: Make restore_processor_context() sane")
kmemleak reports this issue:
unreferenced object 0xf68241e0 (size 32):
comm "swapper/0", pid 1, jiffies 4294668610 (age 68.432s)
hex dump (first 32 bytes):
00 cc cc cc 29 10 01 c0 00 00 00 00 00 00 00 00 ....)...........
00 42 82 f6 cc cc cc cc cc cc cc cc cc cc cc cc .B..............
backtrace:
[<461c1d50>] __kmem_cache_alloc_node+0x106/0x260
[<ea65e13b>] __kmalloc+0x54/0x160
[<c3858cd2>] msr_build_context.constprop.0+0x35/0x100
[<46635aff>] pm_check_save_msr+0x63/0x80
[<6b6bb938>] do_one_initcall+0x41/0x1f0
[<3f3add60>] kernel_init_freeable+0x199/0x1e8
[<3b538fde>] kernel_init+0x1a/0x110
[<938ae2b2>] ret_from_fork+0x1c/0x28
Which is a false positive.
Reproducer:
- Run rsync of whole kernel tree (multiple times if needed).
- start a kmemleak scan
- Note this is just an example: a lot of our internal tests hit these.
The root cause is similar to the fix in:
b0b592cf08 x86/pm: Fix false positive kmemleak report in msr_build_context()
ie. the alignment within the packed struct saved_context
which has everything unaligned as there is only "u16 gs;" at start of
struct where in the past there were four u16 there thus aligning
everything afterwards. The issue is with the fact that Kmemleak only
searches for pointers that are aligned (see how pointers are scanned in
kmemleak.c) so when the struct members are not aligned it doesn't see
them.
Testing:
We run a lot of tests with our CI, and after applying this fix we do not
see any kmemleak issues any more whilst without it we see hundreds of
the above report. From a single, simple test run consisting of 416 individual test
cases on kernel 5.10 x86 with kmemleak enabled we got 20 failures due to this,
which is quite a lot. With this fix applied we get zero kmemleak related failures.
Fixes: 7ee18d6779 ("x86/power: Make restore_processor_context() sane")
Signed-off-by: Anton Altaparmakov <anton@tuxera.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: stable@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20240314142656.17699-1-anton@tuxera.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e7132ed3c ]
There was reported lockup when we exit a snapshot with many exceptions.
Fix this by adding "cond_resched" to the loop that frees the exceptions.
Reported-by: John Pittman <jpittman@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69e3be6893 ]
[Why]
When mode switching is triggered there is momentary noise visible on
some HDMI TV or displays.
[How]
Wait for 2 frames to make sure we have enough time to send out AV mute
and sink receives a full frame.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Leo Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e64b3f55e4 ]
[WHY & HOW]
If the display is null when creating an HDCP session, return a proper
error code.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c6064cbe5 ]
Otherwise after the GTT bo is released, the GTT and gart space is freed
but amdgpu_ttm_backend_unbind will not clear the gart page table entry
and leave valid mapping entry pointing to the stale system page. Then
if GPU access the gart address mistakely, it will read undefined value
instead page fault, harder to debug and reproduce the real issue.
Cc: stable@vger.kernel.org
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cd8adc3e1 ]
Previously, patches have been added to limit the reported count of SATA
ports for asm1064 and asm1166 SATA controllers, as those controllers do
report more ports than physically having.
While it is allowed to report more ports than physically having in CAP.NP,
it is not allowed to report more ports than physically having in the PI
(Ports Implemented) register, which is what these HBAs do.
(This is a AHCI spec violation.)
Unfortunately, it seems that the PMP implementation in these ASMedia HBAs
is also violating the AHCI and SATA-IO PMP specification.
What these HBAs do is that they do not report that they support PMP
(CAP.SPM (Supports Port Multiplier) is not set).
Instead, they have decided to add extra "virtual" ports in the PI register
that is used if a port multiplier is connected to any of the physical
ports of the HBA.
Enumerating the devices behind the PMP as specified in the AHCI and
SATA-IO specifications, by using PMP READ and PMP WRITE commands to the
physical ports of the HBA is not possible, you have to use the "virtual"
ports.
This is of course bad, because this gives us no way to detect the device
and vendor ID of the PMP actually connected to the HBA, which means that
we can not apply the proper PMP quirks for the PMP that is connected to
the HBA.
Limiting the port map will thus stop these controllers from working with
SATA Port Multipliers.
This patch reverts both patches for asm1064 and asm1166, so old behavior
is restored and SATA PMP will work again, but it will also reintroduce the
(minutes long) extra boot time for the ASMedia controllers that do not
have a PMP connected (either on the PCIe card itself, or an external PMP).
However, a longer boot time for some, is the lesser evil compared to some
other users not being able to detect their drives at all.
Fixes: 0077a504e1 ("ahci: asm1166: correct count of reported ports")
Fixes: 9815e39617 ("ahci: asm1064: correct count of reported ports")
Cc: stable@vger.kernel.org
Reported-by: Matt <cryptearth@googlemail.com>
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
[cassel: rewrote commit message]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
