This reverts commits 6a789ba679 and
2433647bc8.
The virtual time scheduler code has a number of issues:
- queues slowed down by hardware/firmware powersave handling were not properly
handled.
- on ath10k in push-pull mode, tx queues that the driver tries to pull from
were starved, causing excessive latency
- delay between tx enqueue and reported airtime use were causing excessively
bursty tx behavior
The bursty behavior may also be present on the round-robin scheduler, but there
it is much easier to fix without introducing additional regressions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the capability to specify gfp_t parameter to
ieeee80211_obss_color_collision_notify routine since it runs in
interrupt context in ieee80211_rx_check_bss_color_collision().
Fixes: 6d945a33f2 ("mac80211: introduce BSS color collision detection")
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/02c990fb3fbd929c8548a656477d20d6c0427a13.1655419135.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to be able to access these in a race-free way under
traffic while adding/removing them, so RCU-ify the pointers.
This requires passing a link_sta to a lot of functions so
we don't have to do the RCU handling everywhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In start_ap and stop_ap mac80211 callbacks pass the link_id
to the drivers.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use link and link_conf according to the link_id
provided by cfg in start_ap/stop_ap and change_beacon.
Also use them in the functions called by them.
Note that for a non MLD device, the link_id is 0,
and link[0] and link_conf[0] equal to deflink and
bss_conf respectively (what was there before).
Also, call vif_info_change for BSS related changes (SSID), and
link_info_change for LINK related changes (instead of the
legacy bss_info_change).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a link is added or removed via nl80211, these are
called. Implement them so we don't have to check in all
the different per-link commands whether we've already
created the necessary datastructures.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary infrastructure, including a new driver
method, to add/remove links to/from a station. To do this,
refactor the link alloc/free a bit, splitting that so we
can do it without linking them, to handle failures better.
Note that a station entry must be created representing an
MLD or a non-MLD STA, it cannot change between the two.
When representing an MLD, the 'deflink' is used for the
first link, which might be removed later, in which case
the memory isn't reused.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start making some SMPS related code MLD-aware. This isn't
really done yet, but again cuts down our 'deflink' reliance.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the channel context code MLO aware, along with some
functions that it uses, so that the chan.c file is now
MLD-clean and no longer uses deflink/bss_conf/etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a few cases we already have the link ID in the APIs,
pass it already even if it cannot be non-zero yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start reorganizing interface related data structures toward
MLD. The most complex part here is for the keys, since we
have to split the various kinds of GTKs off to the link but
still need to use (for WEP) the other keys as a fallback
even for multicast frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's some pretty close code here, with the exception
of RCU dereference vs. protected dereference. Refactor
this to just return a pointer and then do the deref in
the caller later.
Change-Id: Ide5315e2792da6ac66eaf852293306a3ac71ced9
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only driver using this was iwlwifi, where we just removed
the support because it was never really used. Remove the code
from mac80211 as well.
Change-Id: I1667417a5932315ee9d81f5c233c56a354923f09
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
AP may run out of BSS color after color collision
detection event from driver.
Disable BSS color collision detection if no free colors are
available based on bss color disabled bit sent as a part of
NL80211_ATTR_HE_BSS_COLOR attribute sent in
NL80211_CMD_SET_BEACON.
It can be reenabled once new color is available.
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1649867295-7204-3-git-send-email-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NL80211_ATTR_HE_BSS_COLOR attribute can be included in both
NL80211_CMD_START_AP and NL80211_CMD_SET_BEACON commands.
Move he_bss_color from cfg80211_ap_settings to cfg80211_beacon_data
and parse NL80211_ATTR_HE_BSS_COLOR as a part of nl80211_parse_beacon()
to have bss color settings parsed for both start ap and set beacon
commands.
Add a new flag he_bss_color_valid to indicate whether
NL80211_ATTR_HE_BSS_COLOR attribute is included.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1649867295-7204-2-git-send-email-quic_ramess@quicinc.com
[fix build ...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we always track the BSSID there when we get associated,
these are equivalent, but ifmgd->bssid saves a dereference and
thus makes the code a bit smaller, and more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if it is not a real issue since ieee80211_set_after_csa_beacon()
or ieee80211_set_after_color_change_beacon() are run only when csa or bcc
is active, move next_beacon check before running ieee80211_assign_beacon
routine.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/041764ed7e9781bcee66c33b41f1365aa4205932.1649327683.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Trigger ieee80211_csa_finish() on the non-transmitting interfaces
when channel switch concludes on the transmitting interface.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/6fde4d7f9fa387494f46a7aa4a584478dcda06f1.1645702516.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new fields in struct beacon_data to store all MBSSID elements.
Generate a beacon template which includes all MBSSID elements.
Move CSA offset to reflect the MBSSID element length.
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Money Wang <money.wang@mediatek.com>
Link: https://lore.kernel.org/r/5322db3c303f431adaf191ab31c45e151dde5465.1645702516.git.lorenzo@kernel.org
[small cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While commit 6a01afcf84 ("mac80211: mesh: Free ie data when leaving
mesh") fixed a memory leak on mesh leave / teardown it introduced a
potential memory corruption caused by a double free when rejoining the
mesh:
ieee80211_leave_mesh()
-> kfree(sdata->u.mesh.ie);
...
ieee80211_join_mesh()
-> copy_mesh_setup()
-> old_ie = ifmsh->ie;
-> kfree(old_ie);
This double free / kernel panics can be reproduced by using wpa_supplicant
with an encrypted mesh (if set up without encryption via "iw" then
ifmsh->ie is always NULL, which avoids this issue). And then calling:
$ iw dev mesh0 mesh leave
$ iw dev mesh0 mesh join my-mesh
Note that typically these commands are not used / working when using
wpa_supplicant. And it seems that wpa_supplicant or wpa_cli are going
through a NETDEV_DOWN/NETDEV_UP cycle between a mesh leave and mesh join
where the NETDEV_UP resets the mesh.ie to NULL via a memcpy of
default_mesh_setup in cfg80211_netdev_notifier_call, which then avoids
the memory corruption, too.
The issue was first observed in an application which was not using
wpa_supplicant but "Senf" instead, which implements its own calls to
nl80211.
Fixing the issue by removing the kfree()'ing of the mesh IE in the mesh
join function and leaving it solely up to the mesh leave to free the
mesh IE.
Cc: stable@vger.kernel.org
Fixes: 6a01afcf84 ("mac80211: mesh: Free ie data when leaving mesh")
Reported-by: Matthias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Tested-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Link: https://lore.kernel.org/r/20220310183513.28589-1-linus.luessing@c0d3.blue
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ETSI standard defines "Offchannel CAC" as:
"Off-Channel CAC is performed by a number of non-continuous checks
spread over a period in time. This period, which is required to
determine the presence of radar signals, is defined as the Off-Channel
CAC Time..
Minimum Off-Channel CAC Time 6 minutes and Maximum Off-Channel CAC Time
4 hours..".
mac80211 implementation refers to a dedicated hw chain used for continuous
radar monitoring. Rename offchannel_* references to background_* in
order to avoid confusion with ETSI standard.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/4204cc1d648d76b44557981713231e030a3bd991.1638190762.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce a disconnect function that can be used when a
channel switch error occurs. The channel switch can request to
block the tx, and so, we need to make sure we do not send a deauth
frame in this case.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211129152938.cd2a615a0702.I9edb14785586344af17644b610ab5be109dcef00@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When color change is triggered in multiple bssid case, allow
only for transmitting BSS, and when it changes its bss color,
notify the non transmitting BSSs also of the new bss color.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1637146647-16282-1-git-send-email-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Similar to cfg80211, introduce set_radar_offchan callback in mac80211_ops
in order to configure a dedicated offchannel chain available on some hw
(e.g. mt7915) to perform offchannel CAC detection and avoid tx/rx downtime.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/201110606d4f3a7dfdf31440e351f2e2c375d4f0.1634979655.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit a05829a722 ("cfg80211: avoid holding the RTNL when
calling the driver") we've not only been protecting the pointer
to monitor_sdata with the RTNL, but also with the wiphy->mtx. This
is relevant in a number of lockdep assertions, e.g. the one we hit
in ieee80211_set_monitor_channel(). However, we're now protecting
all the assignments/dereferences, even the one in interface iter,
with the wiphy->mtx, so switch over the lockdep assertions to that
lock.
Fixes: a05829a722 ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20211112135143.cb8e8ceffef3.Iaa210f16f6904c8a7a24954fb3396da0ef86ec08@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Configure multiple BSSID and enhanced multi-BSSID advertisement (EMA)
parameters in mac80211 for AP mode.
For each interface, 'mbssid_tx_vif' points to the transmitting interface of
the MBSSID set. The pointer is set to NULL if MBSSID is disabled.
Function ieee80211_stop() is modified to always bring down all the
non-transmitting interfaces first and the transmitting interface last.
Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Aloka Dixit <alokad@codeaurora.org>
Signed-off-by: Aloka Dixit <alokad@codeaurora.org>
Link: https://lore.kernel.org/r/20210916025437.29138-3-alokad@codeaurora.org
[slightly change logic to be more obvious]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The color change announcement is very similar to how CSA works where
we have an IE that includes a counter. When the counter hits 0, the new
color is applied via an updated beacon.
This patch makes the CSA counter functionality reusable, rather than
implementing it again. This also allows for future reuse incase support
for other counter IEs gets added.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/057c1e67b82bee561ea44ce6a45a8462d3da6995.1625247619.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Notify the driver about the 4-address mode change and also send a nulldata
packet to the AP to notify it about the change
Fixes: 1ff4e8f2de ("mac80211: notify the driver when a sta uses 4-address mode")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210702050111.47546-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This switches the airtime scheduler in mac80211 to use a virtual
time-based scheduler instead of the round-robin scheduler used before.
This has a couple of advantages:
- No need to sync up the round-robin scheduler in firmware/hardware with
the round-robin airtime scheduler.
- If several stations are eligible for transmission we can schedule both
of them; no need to hard-block the scheduling rotation until the head
of the queue has used up its quantum.
- The check of whether a station is eligible for transmission becomes
simpler (in ieee80211_txq_may_transmit()).
The drawback is that scheduling becomes slightly more expensive, as we
need to maintain an rbtree of TXQs sorted by virtual time. This means
that ieee80211_register_airtime() becomes O(logN) in the number of
currently scheduled TXQs because it can change the order of the
scheduled stations. We mitigate this overhead by only resorting when a
station changes position in the tree, and hopefully N rarely grows too
big (it's only TXQs currently backlogged, not all associated stations),
so it shouldn't be too big of an issue.
To prevent divisions in the fast path, we maintain both station sums and
pre-computed reciprocals of the sums. This turns the fast-path operation
into a multiplication, with divisions only happening as the number of
active stations change (to re-compute the current sum of all active
station weights). To prevent this re-computation of the reciprocal from
happening too frequently, we use a time-based notion of station
activity, instead of updating the weight every time a station gets
scheduled or de-scheduled. As queues can oscillate between empty and
occupied quite frequently, this can significantly cut down on the number
of re-computations. It also has the added benefit of making the station
airtime calculation independent on whether the queue happened to have
drained at the time an airtime value was accounted.
Co-developed-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210623134755.235545-1-toke@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In some race conditions, with more clients and traffic configuration,
below crash is seen when making the interface down. sta->fast_rx wasn't
cleared when STA gets removed from 4-addr AP_VLAN interface. The crash is
due to try accessing 4-addr AP_VLAN interface's net_device (fast_rx->dev)
which has been deleted already.
Resolve this by clearing sta->fast_rx pointer when STA removes
from a 4-addr VLAN.
[ 239.449529] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 239.449531] pgd = 80204000
...
[ 239.481496] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.60 #227
[ 239.481591] Hardware name: Generic DT based system
[ 239.487665] task: be05b700 ti: be08e000 task.ti: be08e000
[ 239.492360] PC is at get_rps_cpu+0x2d4/0x31c
[ 239.497823] LR is at 0xbe08fc54
...
[ 239.778574] [<80739740>] (get_rps_cpu) from [<8073cb10>] (netif_receive_skb_internal+0x8c/0xac)
[ 239.786722] [<8073cb10>] (netif_receive_skb_internal) from [<8073d578>] (napi_gro_receive+0x48/0xc4)
[ 239.795267] [<8073d578>] (napi_gro_receive) from [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames+0xbcc/0x12d4 [mac80211])
[ 239.804776] [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<c7b84d4c>] (ieee80211_rx_napi+0x7b8/0x8c8 [mac8
0211])
[ 239.815857] [<c7b84d4c>] (ieee80211_rx_napi [mac80211]) from [<c7f63d7c>] (ath11k_dp_process_rx+0x7bc/0x8c8 [ath11k])
[ 239.827757] [<c7f63d7c>] (ath11k_dp_process_rx [ath11k]) from [<c7f5b6c4>] (ath11k_dp_service_srng+0x2c0/0x2e0 [ath11k])
[ 239.838484] [<c7f5b6c4>] (ath11k_dp_service_srng [ath11k]) from [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll+0x20/0x84 [ath11k_ahb]
)
[ 239.849419] [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll [ath11k_ahb]) from [<8073ce1c>] (net_rx_action+0xe0/0x28c)
[ 239.860945] [<8073ce1c>] (net_rx_action) from [<80324868>] (__do_softirq+0xe4/0x228)
[ 239.871269] [<80324868>] (__do_softirq) from [<80324c48>] (irq_exit+0x98/0x108)
[ 239.879080] [<80324c48>] (irq_exit) from [<8035c59c>] (__handle_domain_irq+0x90/0xb4)
[ 239.886114] [<8035c59c>] (__handle_domain_irq) from [<8030137c>] (gic_handle_irq+0x50/0x94)
[ 239.894100] [<8030137c>] (gic_handle_irq) from [<803024c0>] (__irq_svc+0x40/0x74)
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Link: https://lore.kernel.org/r/1616163532-3881-1-git-send-email-seevalam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Coverity reported the strange "if (~...)" condition that's
always true. It suggested that ! was intended instead of ~,
but upon further analysis I'm convinced that what really was
intended was a comparison to 0xff/0xffff (in HT/VHT cases
respectively), since this indicates that all of the rates
are enabled.
Change the comparison accordingly.
I'm guessing this never really mattered because a reset to
not having a rate mask is basically equivalent to having a
mask that enables all rates.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 2ffbe6d333 ("mac80211: fix and optimize MCS mask handling")
Fixes: b119ad6e72 ("mac80211: add rate mask logic for vht rates")
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210212112213.36b38078f569.I8546a20c80bc1669058eb453e213630b846e107b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This change registers ieee80211_set_sar_specs to
mac80211_config_ops, so cfg80211 can call it.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Abhishek Kumar <kuabhs@chromium.org>
Link: https://lore.kernel.org/r/20201203103728.3034-3-cjhuang@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
