prevent_wake logic is backward since what it is really checking is
if the device may wakeup the system or not, not that it will prevent
the to be awaken.
Also looking on how other subsystems have the entry as power/wakeup
this also renames the force_prevent_wake to force_wakeup in vhci driver.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
if platform provide gpio connect to BT_EN reset pin of qca btsoc chip,
we can do hardware reset instead of usb port reset.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The MediaTek chip support vendor specific HCI command(0xfc1a) to
change the public address. Add hdev->set_bdaddr handler for MediaTek
Chip. After doing a power cycle or MediaTek Bluetooth reset, BD_ADDR
will bring back the original one.
Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For the commit of 9e45524a01, wakeup is
always disabled for Realtek devices. However, there's the capability
for Realtek devices to apply USB wakeup.
In this commit, remove WAKEUP_DISABLE feature for Realtek devices.
If users would switch wakeup, they should access
"/sys/bus/usb/.../power/wakeup"
In this commit, it also adds the feature as WAKEUP_AUTOSUSPEND
for Realtek devices because it should set do_remote_wakeup on autosuspend.
Signed-off-by: Max Chou <max.chou@realtek.com>
Tested-by: Hilda Wu <hildawu@realtek.com>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some USB BT adapters don't satisfy the MTU requirement mentioned in
commit e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
and have ALT 3 setting that produces no/garbled audio. Some adapters
with larger MTU were also reported to have problems with ALT 3.
Add a flag and check it and MTU before selecting ALT 3, falling back to
ALT 1. Enable the flag for Realtek, restoring the previous behavior for
non-Realtek devices.
Tested with USB adapters (mtu<72, no/garbled sound with ALT3, ALT1
works) BCM20702A1 0b05:17cb, CSR8510A10 0a12:0001, and (mtu>=72, ALT3
works) RTL8761BU 0bda:8771, Intel AX200 8087:0029 (after disabling
ALT6). Also got reports for (mtu>=72, ALT 3 reported to produce bad
audio) Intel 8087:0a2b.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Fixes: e848dbd364 ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
Tested-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Jonathan Lampérth <jon@h4n.dev>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch moves the hci quirks for Intel devices into the setup
routines and cleaned up the driver flags.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch refactors the setup routines for legacy and TLV based
bootloader devices to the combined setup, and move the related functions
from btusb to btintel.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The some legacy ROM controllers have a bug with the first HCI command
sent to it returning number of completed commands as zero, which would
stall the command processing in the Bluetooth core.
As a workaround, send HCI Rest command first which will reset the
controller to fix the issue.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a data structure for btintel for btintel object, and the
definition of bootloder states. It also adds macros to set/test/clear
the flags.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch refactors the setup routines for legacy ROM product into
combined setup, and move the related functions from btusb to btintel.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the firmware hang or command no response, driver can reset the
bluetooth mcu via USB to recovery it. The reset steps as follows.
1. Cancel USB transfer requests before reset.
2. It use speicific USB HW Register to reset Bluetooth MCU, at the
same time, the USB Endpoint0 still keep alive.
3. Poll the USB HW register until reset is completed by Endpoint0.
4. To recovery unexpected USB state and behavior during resetting the
Bluetooth MCU, the driver need to reset the USB device for MT7921.
5. After the reset is completed, the Bluetooth MCU need to re-setup,
such as download patch, power-on sequence and etc.
Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Reviewed-by: Michael Sun <michaelfsun@google.com>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Mdiatek MT7921(7961) support MSFT HCI extensions, we are using
0xFD30 for VsMsftOpCode.
Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Turns out Hans de Goede completed the work I started last year trying to
improve Chinese-clone detection of CSR controller chips. Quirk after quirk
these Bluetooth dongles are more usable now.
Even after a few BlueZ regressions; these clones are so fickle that some
days they stop working altogether. Except on Windows, they work fine.
But this force-suspend initialization quirk seems to mostly do the trick,
after a lot of testing Bluetooth now seems to work *all* the time.
The only problem is that the solution ended up being masked under a very
stringent check; when there are probably hundreds of fake dongle
models out there that benefit from a good reset. Make it so.
Fixes: 81cac64ba2 ("Bluetooth: Deal with USB devices that are faking CSR vendor")
Fixes: cde1a8a992 ("Bluetooth: btusb: Fix and detect most of the Chinese Bluetooth controllers")
Fixes: d74e0ae7e0 ("Bluetooth: btusb: Fix detection of some fake CSR controllers with a bcdDevice val of 0x0134")
Fixes: 0671c06623 ("Bluetooth: btusb: Add workaround for remote-wakeup issues with Barrot 8041a02 fake CSR controllers")
Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel TyphoonPeak, GarfieldPeak Bluetooth controllers
support the Microsoft vendor extension and they are using
0xFC1E for VsMsftOpCode.
Verified on a GarfieldPeak device through bluetoothctl show
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Michael Sun <michaelfsun@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Qualcomm WCN6855 Bluetooth controller supports the Microsoft vendor
extension, enable them by setting VsMsftOpCode to 0xFD70.
Verified on a WCN6855 device through bluetoothctl show
Signed-off-by: Michael Sun <michaelfsun@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add the valid le states quirk for WCN6855 and GarfieldPeak controller
so the 'central-peripheral' role is exposed in userspace.
Signed-off-by: Michael Sun <michaelfsun@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When reading the support debug features failed, there are not available
features init. Continue to set the debug features is illogical, we should
skip btintel_set_debug_features(), even if check it by "if (!features)".
Fixes: c453b10c2b ("Bluetooth: btusb: Configure Intel debug feature based on available support")
Signed-off-by: Jun Miao <jun.miao@windriver.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is btsoc timing issue, after host start to downloading bt firmware,
ep2 need time to switch from function acl to function dfu, so host add
20ms delay as workaround.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
if boardID is 0, will use the default nvm file without surfix.
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Because mSBC frames do not need to be aligned to the SCO packet
boundary. Using USB ALT 3 let HCI payload >= 60 bytes, let mSBC
data satisfy 60 Bytes avoid payload unaligned situation and fixed
some headset no voise issue.
USB Alt 3 supported also need HFP support transparent MTU in 72 Bytes.
Signed-off-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If btusb_mtk_submit_wmt_recv_urb returns error, wc should be freed and
then error should be returned to prevent memory leak.
Addresses-Coverity: ("Prevent memory leak")
Fixes: 4cbb375e997d ("Bluetooth: btusb: Fixed too many in-token issue for Mediatek Chip.")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
netfilter and wireguard trees.
The bpf vs lockdown+audit fix is the most notable.
Current release - regressions:
- virtio-net: fix page faults and crashes when XDP is enabled
- mlx5e: fix HW timestamping with CQE compression, and make sure they
are only allowed to coexist with capable devices
- stmmac:
- fix kernel panic due to NULL pointer dereference of mdio_bus_data
- fix double clk unprepare when no PHY device is connected
Current release - new code bugs:
- mt76: a few fixes for the recent MT7921 devices and runtime
power management
Previous releases - regressions:
- ice: - track AF_XDP ZC enabled queues in bitmap to fix copy mode Tx
- fix allowing VF to request more/less queues via virtchnl
- correct supported and advertised autoneg by using PHY capabilities
- allow all LLDP packets from PF to Tx
- kbuild: quote OBJCOPY var to avoid a pahole call break the build
Previous releases - always broken:
- bpf, lockdown, audit: fix buggy SELinux lockdown permission checks
- mt76: address the recent FragAttack vulnerabilities not covered
by generic fixes
- ipv6: fix KASAN: slab-out-of-bounds Read in fib6_nh_flush_exceptions
- Bluetooth:
- fix the erroneous flush_work() order, to avoid double free
- use correct lock to prevent UAF of hdev object
- nfc: fix NULL ptr dereference in llcp_sock_getname() after failed connect
- ieee802154: multiple fixes to error checking and return values
- igb: fix XDP with PTP enabled
- intel: add correct exception tracing for XDP
- tls: fix use-after-free when TLS offload device goes down and back up
- ipvs: ignore IP_VS_SVC_F_HASHED flag when adding service
- netfilter: nft_ct: skip expectations for confirmed conntrack
- mptcp: fix falling back to TCP in presence of out of order packets
early in connection lifetime
- wireguard: switch from O(n) to a O(1) algorithm for maintaining peers,
fixing stalls and a large memory leak in the process
Misc:
- devlink: correct VIRTUAL port to not have phys_port attributes
- Bluetooth: fix VIRTIO_ID_BT assigned number
- net: return the correct errno code ENOBUF -> ENOMEM
- wireguard:
- peer: allocate in kmem_cache saving 25% on peer memory
- do not use -O3
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=sNP5
-----END PGP SIGNATURE-----
Merge tag 'net-5.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from bpf, wireless, netfilter and
wireguard trees.
The bpf vs lockdown+audit fix is the most notable.
Things haven't slowed down just yet, both in terms of regressions in
current release and largish fixes for older code, but we usually see a
slowdown only after -rc5.
Current release - regressions:
- virtio-net: fix page faults and crashes when XDP is enabled
- mlx5e: fix HW timestamping with CQE compression, and make sure they
are only allowed to coexist with capable devices
- stmmac:
- fix kernel panic due to NULL pointer dereference of
mdio_bus_data
- fix double clk unprepare when no PHY device is connected
Current release - new code bugs:
- mt76: a few fixes for the recent MT7921 devices and runtime power
management
Previous releases - regressions:
- ice:
- track AF_XDP ZC enabled queues in bitmap to fix copy mode Tx
- fix allowing VF to request more/less queues via virtchnl
- correct supported and advertised autoneg by using PHY
capabilities
- allow all LLDP packets from PF to Tx
- kbuild: quote OBJCOPY var to avoid a pahole call break the build
Previous releases - always broken:
- bpf, lockdown, audit: fix buggy SELinux lockdown permission checks
- mt76: address the recent FragAttack vulnerabilities not covered by
generic fixes
- ipv6: fix KASAN: slab-out-of-bounds Read in
fib6_nh_flush_exceptions
- Bluetooth:
- fix the erroneous flush_work() order, to avoid double free
- use correct lock to prevent UAF of hdev object
- nfc: fix NULL ptr dereference in llcp_sock_getname() after failed
connect
- ieee802154: multiple fixes to error checking and return values
- igb: fix XDP with PTP enabled
- intel: add correct exception tracing for XDP
- tls: fix use-after-free when TLS offload device goes down and back
up
- ipvs: ignore IP_VS_SVC_F_HASHED flag when adding service
- netfilter: nft_ct: skip expectations for confirmed conntrack
- mptcp: fix falling back to TCP in presence of out of order packets
early in connection lifetime
- wireguard: switch from O(n) to a O(1) algorithm for maintaining
peers, fixing stalls and a large memory leak in the process
Misc:
- devlink: correct VIRTUAL port to not have phys_port attributes
- Bluetooth: fix VIRTIO_ID_BT assigned number
- net: return the correct errno code ENOBUF -> ENOMEM
- wireguard:
- peer: allocate in kmem_cache saving 25% on peer memory
- do not use -O3"
* tag 'net-5.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (91 commits)
cxgb4: avoid link re-train during TC-MQPRIO configuration
sch_htb: fix refcount leak in htb_parent_to_leaf_offload
wireguard: allowedips: free empty intermediate nodes when removing single node
wireguard: allowedips: allocate nodes in kmem_cache
wireguard: allowedips: remove nodes in O(1)
wireguard: allowedips: initialize list head in selftest
wireguard: peer: allocate in kmem_cache
wireguard: use synchronize_net rather than synchronize_rcu
wireguard: do not use -O3
wireguard: selftests: make sure rp_filter is disabled on vethc
wireguard: selftests: remove old conntrack kconfig value
virtchnl: Add missing padding to virtchnl_proto_hdrs
ice: Allow all LLDP packets from PF to Tx
ice: report supported and advertised autoneg using PHY capabilities
ice: handle the VF VSI rebuild failure
ice: Fix VFR issues for AVF drivers that expect ATQLEN cleared
ice: Fix allowing VF to request more/less queues via virtchnl
virtio-net: fix for skb_over_panic inside big mode
ipv6: Fix KASAN: slab-out-of-bounds Read in fib6_nh_flush_exceptions
fib: Return the correct errno code
...
Some firmware when operation don't may have broken versions leading to
error like the following:
[ 6.176482] Bluetooth: hci0: Firmware revision 0.0 build 121 week 7 2021
[ 6.177906] bluetooth hci0: Direct firmware load for intel/ibt-20-0-0.sfi failed with error -2
[ 6.177910] Bluetooth: hci0: Failed to load Intel firmware file intel/ibt-20-0-0.sfi (-2)
Since we load the firmware file just to check if its version had changed
comparing to the one already loaded we can just skip since the firmware
is already operation.
Fixes: ac0565462e ("Bluetooth: btintel: Check firmware version before
download")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some models of the RTL8822ce utilize a different USB ID. Add this
new one to the Bluetooth driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/usb/core/hub.c: usb_new_device() contains the following:
/* By default, forbid autosuspend for all devices. It will be
* allowed for hubs during binding.
*/
usb_disable_autosuspend(udev);
So for anything which is not a hub, such as btusb devices, autosuspend is
disabled by default and we must call usb_enable_autosuspend(udev) to
enable it.
This means that the "Fix the autosuspend enable and disable" commit,
which drops the usb_enable_autosuspend() call when the enable_autosuspend
module option is true, is completely wrong, revert it.
This reverts commit 7bd9fb058d.
Cc: Hui Wang <hui.wang@canonical.com>
Fixes: 7bd9fb058d ("Bluetooth: btusb: Fix the autosuspend enable and disable")
Acked-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adding support LE scatternet and WBS for Mediatek Chip
Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves duplicated code for waiting firmware download completion to
a function that can be reused.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves duplicated code for waiting firmware download completion to
a function that can be reused.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves version checks of intel_version() to btintel_version_info().
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves version checks of intel_version_tlv() to btintel_version_info_tlv().
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to allow new firmware to load, it first needs to check if the
firmware version on file matches the one loaded if it doesn't, then it
needs to revert to bootloader mode in order to load the new firmware.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This checks the firmware build number, week and year against the
repective loaded version. If details are a match, skip the download
process.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
print the firmware file name on error loading from fie system
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Luiz Augusto von Dentz