If the imx-sdma driver is built as a module, the fsl-sai device doesn't
disable on probing failure, which causes the warning in the next probing:
==================================================================
fsl-sai 308a0000.sai: Unbalanced pm_runtime_enable!
fsl-sai 308a0000.sai: Unbalanced pm_runtime_enable!
fsl-sai 308a0000.sai: Unbalanced pm_runtime_enable!
fsl-sai 308a0000.sai: Unbalanced pm_runtime_enable!
fsl-sai 308a0000.sai: Unbalanced pm_runtime_enable!
fsl-sai 308a0000.sai: Unbalanced pm_runtime_enable!
==================================================================
Disabling the device properly fixes the issue.
Fixes: 812ad463e0 ("ASoC: fsl_sai: Add support for runtime pm")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20200205160436.3813642-1-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The LS1028A SoC uses the same interrupt line for adjacent SAIs. Use
IRQF_SHARED to be able to use these SAIs simultaneously.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20191128223802.18228-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
EDMA requires the period size to be multiple of maxburst. Otherwise the
remaining bytes are not transferred and thus noise is produced.
We can handle this issue by adding a constraint on
SNDRV_PCM_HW_PARAM_PERIOD_SIZE to be multiple of tx/rx maxburst value.
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190913192807.8423-2-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is to allow machine drivers to set a certain bitclk rate
which might not be exactly rate * frame size.
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Viorel Suman <viorel.suman@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190830215910.31590-1-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SAI module on imx8qm features a register map similar with imx6 series
(it doesn't have VERID and PARAM registers at the beginning
of address spece).
Also, it has one FIFO which can help up to 64 * 32 bit samples.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20190814082911.665-2-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SAI module on imx7ulp/imx8m features 2 new registers (VERID and PARAM)
at the beginning of register address space.
On imx7ulp FIFOs can held up to 16 x 32 bit samples.
On imx8mq FIFOs can held up to 128 x 32 bit samples.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190806151214.6783-5-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
New IP version introduces Version ID and Parameter registers
and optionally added Timestamp feature.
VERID and PARAM registers are placed at the top of registers
address space and some registers are shifted according to
the following table:
Tx/Rx data registers and Tx/Rx FIFO registers keep their
addresses, all other registers are shifted by 8.
SAI Memory map is described in chapter 13.10.4.1.1 I2S Memory map
of the Reference Manual [1].
In order to make as less changes as possible we attach an offset
to each register offset to each changed register definition. The
offset is read from each board private data.
[1]https://cache.nxp.com/secured/assets/documents/en/reference-manual/IMX8MDQLQRM.pdf?__gda__=1563728701_38bea7f0f726472cc675cb141b91bec7&fileExt=.pdf
Signed-off-by: Mihai Serban <mihai.serban@nxp.com>
[initial coding in the NXP internal tree]
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
[bugfixing and cleanups]
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
[adapted to linux-next]
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190806151214.6783-4-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tx channel enable (TCE) / Rx channel enable (RCE) bits
enable corresponding data channel for Tx/Rx operation.
Because SAI supports up the 8 channels TCE/RCE occupy
up the 8 bits inside TCR3/RCR3 registers we need to extend
the mask to reflect this.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190806151214.6783-3-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SAI IP supports up to 8 data lines. The configuration of
supported number of data lines is decided at SoC integration
time.
This patch adds definitions for all related data TX/RX registers:
* TDR0..7, Transmit data register
* TFR0..7, Transmit FIFO register
* RDR0..7, Receive data register
* RFR0..7, Receive FIFO register
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Link: https://lore.kernel.org/r/20190806151214.6783-2-daniel.baluta@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: alsa-devel@alsa-project.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-50-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA request schould be triggered as soon as the FIFO has space
for another burst. As different versions of the SAI block have
different FIFO sizes, the watrmark level needs to be derived from
version specific data.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Link: https://lore.kernel.org/r/20190717105635.18514-3-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
New revisions of the SAI IP block have even more differences that need
be taken into account by the driver. To avoid sprinking compatible
checks all over the driver move the current differences into of_match_data.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20190717105635.18514-2-l.stach@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Turn off/on clocks when device enters suspend/resume. This
can help saving power.
As a further optimization, we turn off/on mclk only when SAI
is in master mode because otherwise mclk is externally provided.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Viorel Suman <viorel.suman@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Build warning being reported:
sound/soc/fsl/fsl_sai.c: In function 'fsl_sai_remove':
sound/soc/fsl/fsl_sai.c:921:1: warning: no return statement in
function returning non-void [-Wreturn-type]
So this patch just adds a "return 0" to fix it.
Fixes: 812ad463e0 ("ASoC: fsl_sai: Add support for runtime pm")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Basically the same actions as for system PM, so make use
of pm_runtime_force_suspend/pm_runtime_force_resume.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
is_slave_mode defaults to false because sai structure
that contains it is kzalloc'ed.
Anyhow, if we decide to set the following configuration
SAI slave -> SAI master, is_slave_mode will remain set on true
although SAI being master it should be set to false.
Fix this by updating is_slave_mode for each call of
fsl_sai_set_dai_fmt.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When stopping audio, ASoC will first stop DMA then CPU DAI.
Sometimes there is a delay between DMA stop and CPU DAI stop, which
triggers an underrun error. Now, because of the delay introduced
by dev_err another underrun error will occur causing a vicious circle
making impossible to stop CPU DAI.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FSL SAI can support up to 32 channels using TDM. Report that value so
they can actually be used.
Tested using 8 channels.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'np' variable is already assigned to 'pdev->dev.of_node', so use
it to improve readability.
No functional change.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On mx6ul the General Purpose Register 1 (GPR1) contains the following
bits for configuring the direction of the SAI MCLKs:
SAI1_MCLK_DIR, SAI2_MCLK_DIR, SAI3_MCLK_DIR
Introduce the "fsl,sai-mclk-direction-output" optional property to allow
configuring the SAI_MCLK outputs.
Tested on a imx6ul-evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MX6UL may need to configure the General Purpose Register 1 (GPR1), so
it is better to add a new compatible string to differentiate.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since msleep() will sleep longer than intended time for values less
than 20ms, this patch allows the use of usleep_range for just 1ms.
usleep_range is a finer precision implementation of msleep and is
designed to be a drop-in replacement for udelay where a precise
sleep/busy-wait is unnecessary.
More details see Documentation/timers/timers-howto.txt.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After several open/close sai test with ctrl+c, there will be
I/O error. The SAI can't work anymore, can't recover. There
will be no frame clock. With adding the software reset in
trigger stop, the issue can be fixed.
This is a hardware bug/errata and reset is the only option.
According to the reference manual, the software reset doesn't
reset any control register but only internal hardware logics
such as bit clock generator, status flags, and FIFO pointers.
(Our purpose is just to reset the clock generator while the
software reset is the only way to do that.)
Since slave mode doesn't use the clock generator, only apply
the reset procedure to the master mode.
For asynchronous mode, TX will not be reset when RX is still
running. In this case, i can't reproduce this issue.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
using params_width function to simplify code.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add tdm slots operation support. If tdm slots and slot width have
been configured in machine driver, we should use these values.
Otherwise, using relevant channels and word length to set slots
and slot width.
SAI will generate BCLK depends on sample rate, slots and slot width.
And there may be unused BCLK cycles before each LRCLK transition.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For SAI master mode, when Tx(Rx) sync with Rx(Tx) clock, Rx(Tx) will
generate bclk and frame clock for Tx(Rx), we should set RCR4(TCR4),
RCR5(TCR5) and RMR(TMR) for playback(capture), or there will be sync
error sometimes.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In fsl_sai_set_bclk function, we should not set bclk for Tx/Rx Synchronous
with another SAI mode.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
FSL_SAI_TDR register is writable and not readable. According to
regmap_volatile() function, if FSL_SAI_TDR want to be volatile,
it should be readable. So we should remove FSL_SAI_TDR from volatile
register list.
If the flat cache don't have default register map, when do regcache_sync
operation, the non volatile and writable registers will be synchronised
to 0. FSL_SAI_TDR reigster will be written a 0 and cause channel swap.
So add default register map for flat cache, and such register will not
be written.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the Rx clock for both, transmitter and receiver, the
transmitter needs to be set to synchronous with receiver.
This reverts 855675f6e6 ("ASoC: fsl_sai: Set SYNC bit of TCR2 to
Asynchronous Mode"), which, judiging from the commit log, seems to
mixed up between the two synchronous modes: The boolean
sai->synchronous[TX] is indicating wheather the SAI should work in
Rx synchronous mode (sync Tx with Rx), hence if the value is true,
the SYNC field of TCR2 needs to be set to 0x1 ("Synchronous with
receiver").
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change them to #ifdef as CONFIG_PM_SLEEP might not be defined at all.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rate constraints in this driver are shared between all device
instances. It should not be (and is not) modified at runtime, so make them
const.
While we are at it also change the type of the rates array from u32 to
unsigned int. While both resolve to the same type, u32 is usually used to
empathize that the value is for a 32-bit hardware register or similar which
makes it slightly confusing in this context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For i.MX6 SoloX, there is a mode of the SoC to shutdown all power source of
modules during system suspend and resume procedure. Thus, SAI needs to save
all the values of registers before the system suspend and restore them after
the system resume.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the ssi is not the only cpu dai, there are esai, spdif, sai.
and imx_pcm_dma can be used by all of them. Especially ESAI need
a larger DMA buffer size. So Add dedicated DMA buffer for each cpu
dai.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Normally we don't support 12kHz, 24kHz in audio driver, alsa didn't
have formal definition of 12kHz, 24kHz, but alsa supply a way to
support these sample rates. And add 176.4kHz and 192kHz support.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When sai works on master mode, set its bit clock and frame clock.
SAI has 4 MCLK source, bus clock, MCLK1, MCLK2 and MCLK3. fsl_sai_set_bclk
will select proper MCLK source, then calculate and set the bit clock divider.
After fsl_sai_set_bclk, enable the selected mclk in hw_params(), and add
hw_free() to disable the mclk.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whether residue can be reported or not is not a property of the audio
controller but of the DMA controller. The FLAG_NO_RESIDUE was initially
added when the DMAengine framework had no support for describing the residue
reporting capabilities of the controller. Support for this was added quite a
while ago and recently the DMAengine framework started to complain if a
driver does not describe its capabilities and a lot of patches have been
merged that add support for this where it was missing. So it should be safe
to assume that driver on actively used platforms properly implement the DMA
capabilities API.
This patch makes the FLAG_NO_RESIDUE internal and no longer allows audio
controller drivers to manually set the flag. If a DMA driver against
expectations does not support reporting its capabilities for now the generic
DMAengine PCM driver will now emit a warning and simply assume that residue
reporting is not supported. In the future this might be changed to aborting
with an error.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'big-endian-data' property is originally used to indicate whether the
LSB firstly or MSB firstly will be transmitted to the CODEC or received
from the CODEC, and there has nothing relation to the memory data.
Generally, if the audio data in big endian format, which will be using the
bytes reversion, Here this can only be used to bits reversion.
So using the 'lsb-first' instead of 'big-endian-data' can make the code
to be readable easier and more easy to understand what this property is
used to do.
This property used for configuring whether the LSB or the MSB is transmitted
first for the fifo data.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
