In preparation of supporting data plane forwarding on behalf of a
software bridge, some drivers might need to view bridges as virtual
switches behind the CPU port in a cross-chip topology.
Give them some help and let them know how many physical switches there
are in the tree, so that they can count the virtual switches starting
from that number on.
Note that the first dsa_switch_ops method where this information is
reliably available is .setup(). This is because of how DSA works:
in a tree with 3 switches, each calling dsa_register_switch(), the first
2 will advance until dsa_tree_setup() -> dsa_tree_setup_routing_table()
and exit with error code 0 because the topology is not complete. Since
probing is parallel at this point, one switch does not know about the
existence of the other. Then the third switch comes, and for it,
dsa_tree_setup_routing_table() returns complete = true. This switch goes
ahead and calls dsa_tree_setup_switches() for everybody else, calling
their .setup() methods too. This acts as the synchronization point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switchdevs to forward frames from the CPU in accordance with the
bridge configuration in the same way as is done between bridge
ports. This means that the bridge will only send a single skb towards
one of the ports under the switchdev's control, and expects the driver
to deliver the packet to all eligible ports in its domain.
Primarily this improves the performance of multicast flows with
multiple subscribers, as it allows the hardware to perform the frame
replication.
The basic flow between the driver and the bridge is as follows:
- When joining a bridge port, the switchdev driver calls
switchdev_bridge_port_offload() with tx_fwd_offload = true.
- The bridge sends offloadable skbs to one of the ports under the
switchdev's control using skb->offload_fwd_mark = true.
- The switchdev driver checks the skb->offload_fwd_mark field and lets
its FDB lookup select the destination port mask for this packet.
v1->v2:
- convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long
- introduce a static key "br_switchdev_fwd_offload_used" to minimize the
impact of the newly introduced feature on all the setups which don't
have hardware that can make use of it
- introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache
line access
- reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in
__br_forward()
- do not strip VLAN on egress if forwarding offload on VLAN-aware bridge
is being used
- propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP
v2->v3:
- replace the solution based on .ndo_dfwd_add_station with a solution
based on switchdev_bridge_port_offload
- rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD
v3->v4: rebase
v4->v5:
- make sure the static key is decremented on bridge port unoffload
- more function and variable renaming and comments for them:
br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload
br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload
nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom
nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload
fwd_accel to tx_fwd_offload
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
compat_ifreq_ioctl() is one of the last users of copy_in_user() and
compat_alloc_user_space(), as it attempts to convert the 'struct ifreq'
arguments from 32-bit to 64-bit format as used by dev_ioctl() and a
couple of socket family specific interpretations.
The current implementation works correctly when calling dev_ioctl(),
inet_ioctl(), ieee802154_sock_ioctl(), atalk_ioctl(), qrtr_ioctl()
and packet_ioctl(). The ioctl handlers for x25, netrom, rose and x25 do
not interpret the arguments and only block the corresponding commands,
so they do not care.
For af_inet6 and af_decnet however, the compat conversion is slightly
incorrect, as it will copy more data than the native handler accesses,
both of them use a structure that is shorter than ifreq.
Replace the copy_in_user() conversion with a pair of accessor functions
to read and write the ifreq data in place with the correct length where
needed, while leaving the other ones to copy the (already compatible)
structures directly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_ifconf() calling conventions make compat handling
more complicated than necessary, simplify this by moving
the in_compat_syscall() check into the function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dynamic registration of the gifconf() helper is only used for
IPv4, and this can not be in a loadable module, this can be simplified
noticeably by turning it into a direct function call as a preparation
for cleaning up the compat handling.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIOCGIFMAP and SIOCSIFMAP currently require compat_alloc_user_space()
and copy_in_user() for compat mode.
Move the compat handling into the location where the structures are
actually used, to avoid using those interfaces and get a clearer
implementation.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool compat ioctl handling is hidden away in net/socket.c,
which introduces a couple of minor oddities:
- The implementation may end up diverging, as seen in the RXNFC
extension in commit 84a1d9c482 ("net: ethtool: extend RXNFC
API to support RSS spreading of filter matches") that does not work
in compat mode.
- Most architectures do not need the compat handling at all
because u64 and compat_u64 have the same alignment.
- On x86, the conversion is done for both x32 and i386 user space,
but it's actually wrong to do it for x32 and cannot work there.
- On 32-bit Arm, it never worked for compat oabi user space, since
that needs to do the same conversion but does not.
- It would be nice to get rid of both compat_alloc_user_space()
and copy_in_user() throughout the kernel.
None of these actually seems to be a serious problem that real
users are likely to encounter, but fixing all of them actually
leads to code that is both shorter and more readable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiling without CONFIG_SYSCTL, this warning appears:
net/ipv6/addrconf.c:99:12: error: 'ioam6_if_id_max' defined but not used [-Werror=unused-variable]
99 | static u32 ioam6_if_id_max = U16_MAX;
| ^~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Simply moving the declaration of this variable under ...
#ifdef CONFIG_SYSCTL
... with other similar variables fixes the issue.
Fixes: 9ee11f0fff ("ipv6: ioam: Data plane support for Pre-allocated Trace")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test if we actually can send/receive packets with MTU size. This kind of
issue was detected on ASIX HW with bogus EEPROM.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 4th parameter in tc_chain_notify() should be flags rather than seq.
Let's change it back correctly.
Fixes: 32a4f5ecd7 ("net: sched: introduce chain object to uapi")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly introduced switchdev_handle_fdb_{add,del}_to_device helpers
solved a problem but introduced another one. They have a severe design
bug: they do not propagate FDB events on foreign interfaces to us, i.e.
this use case:
br0
/ \
/ \
/ \
/ \
swp0 eno0
(switchdev) (foreign)
when an address is learned on eno0, what is supposed to happen is that
this event should also be propagated towards swp0. Somehow I managed to
convince myself that this did work correctly, but obviously it does not.
The trouble with foreign interfaces is that we must reach a switchdev
net_device pointer through a foreign net_device that has no direct
upper/lower relationship with it. So we need to do exploratory searching
through the lower interfaces of the foreign net_device's bridge upper
(to reach swp0 from eno0, we must check its upper, br0, for lower
interfaces that pass the check_cb and foreign_dev_check_cb). This is
something that the previous code did not do, it just assumed that "dev"
will become a switchdev interface at some point, somehow, probably by
magic.
With this patch, assisted address learning on the CPU port works again
in DSA:
ip link add br0 type bridge
ip link set swp0 master br0
ip link set eno0 master br0
ip link set br0 up
[ 46.708929] mscc_felix 0000:00:00.5 swp0: Adding FDB entry towards eno0, addr 00:04:9f:05:f4:ab vid 0 as host address
Fixes: 8ca07176ab ("net: switchdev: introduce a fanout helper for SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE")
Reported-by: Eric Woudstra <ericwouds@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 4f2673b3a2 ("net: bridge: add helper to replay
port and host-joined mdb entries"), DSA has introduced some bridge
helpers that replay switchdev events (FDB/MDB/VLAN additions and
deletions) that can be lost by the switchdev drivers in a variety of
circumstances:
- an IP multicast group was host-joined on the bridge itself before any
switchdev port joined the bridge, leading to the host MDB entries
missing in the hardware database.
- during the bridge creation process, the MAC address of the bridge was
added to the FDB as an entry pointing towards the bridge device
itself, but with no switchdev ports being part of the bridge yet, this
local FDB entry would remain unknown to the switchdev hardware
database.
- a VLAN/FDB/MDB was added to a bridge port that is a LAG interface,
before any switchdev port joined that LAG, leading to the hardware
database missing those entries.
- a switchdev port left a LAG that is a bridge port, while the LAG
remained part of the bridge, and all FDB/MDB/VLAN entries remained
installed in the hardware database of the switchdev port.
Also, since commit 0d2cfbd41c ("net: bridge: ignore switchdev events
for LAG ports which didn't request replay"), DSA introduced a method,
based on a const void *ctx, to ensure that two switchdev ports under the
same LAG that is a bridge port do not see the same MDB/VLAN entry being
replayed twice by the bridge, once for every bridge port that joins the
LAG.
With so many ordering corner cases being possible, it seems unreasonable
to expect a switchdev driver writer to get it right from the first try.
Therefore, now that DSA has experimented with the bridge replay helpers
for a little bit, we can move the code to the bridge driver where it is
more readily available to all switchdev drivers.
To convert the switchdev object replay helpers from "pull mode" (where
the driver asks for them) to a "push mode" (where the bridge offers them
automatically), the biggest problem is that the bridge needs to be aware
when a switchdev port joins and leaves, even when the switchdev is only
indirectly a bridge port (for example when the bridge port is a LAG
upper of the switchdev).
Luckily, we already have a hook for that, in the form of the newly
introduced switchdev_bridge_port_offload() and
switchdev_bridge_port_unoffload() calls. These offer a natural place for
hooking the object addition and deletion replays.
Extend the above 2 functions with:
- pointers to the switchdev atomic notifier (for FDB replays) and the
blocking notifier (for MDB and VLAN replays).
- the "const void *ctx" argument required for drivers to be able to
disambiguate between which port is targeted, when multiple ports are
lowers of the same LAG that is a bridge port. Most of the drivers pass
NULL to this argument, except the ones that support LAG offload and have
the proper context check already in place in the switchdev blocking
notifier handler.
Also unexport the replay helpers, since nobody except the bridge calls
them directly now.
Note that:
(a) we abuse the terminology slightly, because FDB entries are not
"switchdev objects", but we count them as objects nonetheless.
With no direct way to prove it, I think they are not modeled as
switchdev objects because those can only be installed by the bridge
to the hardware (as opposed to FDB entries which can be propagated
in the other direction too). This is merely an abuse of terms, FDB
entries are replayed too, despite not being objects.
(b) the bridge does not attempt to sync port attributes to newly joined
ports, just the countable stuff (the objects). The reason for this
is simple: no universal and symmetric way to sync and unsync them is
known. For example, VLAN filtering: what to do on unsync, disable or
leave it enabled? Similarly, STP state, ageing timer, etc etc. What
a switchdev port does when it becomes standalone again is not really
up to the bridge's competence, and the driver should deal with it.
On the other hand, replaying deletions of switchdev objects can be
seen a matter of cleanup and therefore be treated by the bridge,
hence this patch.
We make the replay helpers opt-in for drivers, because they might not
bring immediate benefits for them:
- nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(),
so br_vlan_replay() should not do anything for the new drivers on
which we call it. The existing drivers where there was even a slight
possibility for there to exist a VLAN on a bridge port before they
join it are already guarded against this: mlxsw and prestera deny
joining LAG interfaces that are members of a bridge.
- br_fdb_replay() should now notify of local FDB entries, but I patched
all drivers except DSA to ignore these new entries in commit
2c4eca3ef7 ("net: bridge: switchdev: include local flag in FDB
notifications"). Driver authors can lift this restriction as they
wish, and when they do, they can also opt into the FDB replay
functionality.
- br_mdb_replay() should fix a real issue which is described in commit
4f2673b3a2 ("net: bridge: add helper to replay port and host-joined
mdb entries"). However most drivers do not offload the
SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw
offload this switchdev object, and I don't completely understand the
way in which they offload this switchdev object anyway. So I'll leave
it up to these drivers' respective maintainers to opt into
br_mdb_replay().
So most of the drivers pass NULL notifier blocks for the replay helpers,
except:
- dpaa2-switch which was already acked/regression-tested with the
helpers enabled (and there isn't much of a downside in having them)
- ocelot which already had replay logic in "pull" mode
- DSA which already had replay logic in "pull" mode
An important observation is that the drivers which don't currently
request bridge event replays don't even have the
switchdev_bridge_port_{offload,unoffload} calls placed in proper places
right now. This was done to avoid unnecessary rework for drivers which
might never even add support for this. For driver writers who wish to
add replay support, this can be used as a tentative placement guide:
https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a desire to make the object and FDB replay helpers optional
when moving them inside the bridge driver. For example a certain driver
might not offload host MDBs and there is no case where the replay
helpers would be of immediate use to it.
So it would be nice if we could allow drivers to pass NULL pointers for
the atomic and blocking notifier blocks, and the replay helpers to do
nothing in that case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).
Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.
Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.
+-- br0 ---+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.
But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.
- If we set it to 0, then the bridge will forward it towards swp1, swp2
and bond0. But the switch has already forwarded it towards swp1 and
swp2 (not to bond0, remember, that isn't offloaded, so as far as the
switch is concerned, ports swp3 and swp4 are not looking up the FDB,
and the entire bond0 is a destination that is strictly behind the
CPU). But we don't want duplicated traffic towards swp1 and swp2, so
it's not ok to set skb->offload_fwd_mark = 0.
- If we set it to 1, then the bridge will not forward the skb towards
the ports with the same switchdev mark, i.e. not to swp1, swp2 and
bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
have forwarded the skb there.
So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.
A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.
Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v
call_netdevice_notifiers
|
v
dsa_slave_netdevice_event
|
v
oh, hey! it's for me!
|
v
.port_bridge_join
What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | hardware domain for
v | this port, and zero
dsa_slave_netdevice_event | if I got nothing.
| |
v |
oh, hey! it's for me! |
| |
v |
.port_bridge_join |
| |
+------------------------+
switchdev_bridge_port_offload(swp0, swp0)
Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.
The offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | switchdev mark for
v | bond0.
dsa_slave_netdevice_event | Coincidentally (or not),
| | bond0 and swp0, swp1, swp2
v | all have the same switchdev
hmm, it's not quite for me, | mark now, since the ASIC
but my driver has already | is able to forward towards
called .port_lag_join | all these ports in hw.
for it, because I have |
a port with dp->lag_dev == bond0. |
| |
v |
.port_bridge_join |
for swp3 and swp4 |
| |
+------------------------+
switchdev_bridge_port_offload(bond0, swp3)
switchdev_bridge_port_offload(bond0, swp4)
And the non-offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge waiting:
call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload
| | wasn't called, okay, I'll use a
v | hwdom of zero for this one.
dsa_slave_netdevice_event : Then packets received on swp0 will
| : not be software-forwarded towards
v : swp1, but they will towards bond0.
it's not for me, but
bond0 is an upper of swp3
and swp4, but their dp->lag_dev
is NULL because they couldn't
offload it.
Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.
This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.
Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.
For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hwdoms have only been used thus far for equality comparisons, the
bridge has used the simplest possible assignment policy; using a
counter to keep track of the last value handed out.
With the upcoming transmit offloading, we need to perform set
operations efficiently based on hwdoms, e.g. we want to answer
questions like "has this skb been forwarded to any port within this
hwdom?"
Move to a bitmap-based allocation scheme that recycles hwdoms once all
members leaves the bridge. This means that we can use a single
unsigned long to keep track of the hwdoms that have received an skb.
v1->v2: convert the typedef DECLARE_BITMAP(br_hwdom_map_t, BR_HWDOM_MAX)
into a plain unsigned long.
v2->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, four related - but distinct - concepts where named
offload_fwd_mark:
- skb->offload_fwd_mark: Set by the switchdev driver if the underlying
hardware has already forwarded this frame to the other ports in the
same hardware domain.
- nbp->offload_fwd_mark: An idetifier used to group ports that share
the same hardware forwarding domain.
- br->offload_fwd_mark: Counter used to make sure that unique IDs are
used in cases where a bridge contains ports from multiple hardware
domains.
- skb->cb->offload_fwd_mark: The hardware domain on which the frame
ingressed and was forwarded.
Introduce the term "hardware forwarding domain" ("hwdom") in the
bridge to denote a set of ports with the following property:
If an skb with skb->offload_fwd_mark set, is received on a port
belonging to hwdom N, that frame has already been forwarded to all
other ports in hwdom N.
By decoupling the name from "offload_fwd_mark", we can extend the
term's definition in the future - e.g. to add constraints that
describe expected egress behavior - without overloading the meaning of
"offload_fwd_mark".
- nbp->offload_fwd_mark thus becomes nbp->hwdom.
- br->offload_fwd_mark becomes br->last_hwdom.
- skb->cb->offload_fwd_mark becomes skb->cb->src_hwdom. The slight
change in naming here mandates a slight change in behavior of the
nbp_switchdev_frame_mark() function. Previously, it only set this
value in skb->cb for packets with skb->offload_fwd_mark true (ones
which were forwarded in hardware). Whereas now we always track the
incoming hwdom for all packets coming from a switchdev (even for the
packets which weren't forwarded in hardware, such as STP BPDUs, IGMP
reports etc). As all uses of skb->cb->offload_fwd_mark were already
gated behind checks of skb->offload_fwd_mark, this will not introduce
any functional change, but it paves the way for future changes where
the ingressing hwdom must be known for frames coming from a switchdev
regardless of whether they were forwarded in hardware or not
(basically, if the skb comes from a switchdev, skb->cb->src_hwdom now
always tracks which one).
A typical example where this is relevant: the switchdev has a fixed
configuration to trap STP BPDUs, but STP is not running on the bridge
and the group_fwd_mask allows them to be forwarded. Say we have this
setup:
br0
/ | \
/ | \
swp0 swp1 swp2
A BPDU comes in on swp0 and is trapped to the CPU; the driver does not
set skb->offload_fwd_mark. The bridge determines that the frame should
be forwarded to swp{1,2}. It is imperative that forward offloading is
_not_ allowed in this case, as the source hwdom is already "poisoned".
Recording the source hwdom allows this case to be handled properly.
v2->v3: added code comments
v3->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the checksum calculation is offloaded to the network device (e.g due to
NETIF_F_HW_CSUM inherited from the DSA master device), the calculated
layer 4 checksum is incorrect. This is since the DSA tag which is placed
after the layer 4 data is considered as being part of the daa and thus
errorneously included into the checksum calculation.
To avoid this, always calculate the layer 4 checksum in software.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function skb_put() that is used by tail taggers to make room for the
DSA tag must only be called for linearized SKBS. However in case that the
slave device inherited features like NETIF_F_HW_SG or NETIF_F_FRAGLIST the
SKB passed to the slaves transmit function may not be linearized.
Avoid those SKBs by clearing the NETIF_F_HW_SG and NETIF_F_FRAGLIST flags
for tail taggers.
Furthermore since the tagging protocol can be changed at runtime move the
code for setting up the slaves features into dsa_slave_setup_tagger().
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple complaints have been raised from the TFO users on the internet
stating that the TFO blackhole logic is too aggressive and gets falsely
triggered too often.
(e.g. https://blog.apnic.net/2021/07/05/tcp-fast-open-not-so-fast/)
Considering that most middleboxes no longer drop TFO packets, we decide
to disable the blackhole logic by setting
/proc/sys/net/ipv4/tcp_fastopen_blackhole_timeout_set to 0 by default.
Fixes: cf1ef3f071 ("net/tcp_fastopen: Disable active side TFO in certain scenarios")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding bridge multicast context support for host-joined groups is easy
because we only need the proper timer value. We pass the already chosen
context and use its timer value.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Choose the proper bridge multicast context when user-spaces is adding
mdb entries. Currently we require the vlan to be configured on at least
one device (port or bridge) in order to add an mdb entry if vlan
mcast snooping is enabled (vlan snooping implies vlan filtering).
Note that we always allow deleting an entry, regardless of the vlan state.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in sctp_packet_config(), sctp_transport_pmtu_check() is
called to update transport pathmtu with dst's mtu when dst's mtu
has been changed by non sctp stack like xfrm.
However, this should only happen when SPP_PMTUD_ENABLE is set, no
matter where dst's mtu changed. This patch is to fix by checking
SPP_PMTUD_ENABLE flag before calling sctp_transport_pmtu_check().
Thanks Jacek for reporting and looking into this issue.
v1->v2:
- add the missing "{" to fix the build error.
Fixes: 69fec325a6 ('Revert "sctp: remove sctp_transport_pmtu_check"')
Reported-by: Jacek Szafraniec <jacek.szafraniec@nokia.com>
Tested-by: Jacek Szafraniec <jacek.szafraniec@nokia.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_grow_window() is using skb->len/skb->truesize to increase tp->rcv_ssthresh
which has a direct impact on advertized window sizes.
We added TCP coalescing in linux-3.4 & linux-3.5:
Instead of storing skbs with one or two MSS in receive queue (or OFO queue),
we try to append segments together to reduce memory overhead.
High performance network drivers tend to cook skb with 3 parts :
1) sk_buff structure (256 bytes)
2) skb->head contains room to copy headers as needed, and skb_shared_info
3) page fragment(s) containing the ~1514 bytes frame (or more depending on MTU)
Once coalesced into a previous skb, 1) and 2) are freed.
We can therefore tweak the way we compute len/truesize ratio knowing
that skb->truesize is inflated by 1) and 2) soon to be freed.
This is done only for in-order skb, or skb coalesced into OFO queue.
The result is that low rate flows no longer pay the memory price of having
low GRO aggregation factor. Same result for drivers not using GRO.
This is critical to allow a big enough receiver window,
typically tcp_rmem[2] / 2.
We have been using this at Google for about 5 years, it is due time
to make it upstream.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent change to use bridge/port multicast context pointers
instead of bridge/port I missed to convert two locations which pass the
port pointer as-is, but with the new model we need to verify the port
context is non-NULL first and retrieve the port from it. The first
location is when doing querier selection when a query is received, the
second location is when leaving a group. The port context will be null
if the packets originated from the bridge device (i.e. from the host).
The fix is simple just check if the port context exists and retrieve
the port pointer from it.
Fixes: adc47037a7 ("net: bridge: multicast: use multicast contexts instead of bridge or port")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For tcp sockets, sk->sk_write_space is most probably sk_stream_write_space().
Other sk->sk_write_space() calls in TCP are slow path and do not deserve
any change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d26796ae58 ("udp: check udp sock encap_type in __udp_lib_err")
added checks for encapsulated sockets but it broke cases when there is
no implementation of encap_err_lookup for encapsulation, i.e. ESP in
UDP encapsulation. Fix it by calling encap_err_lookup only if socket
implements this method otherwise treat it as legal socket.
Fixes: d26796ae58 ("udp: check udp sock encap_type in __udp_lib_err")
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a call trace:
BUG: KASAN: use-after-free in sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112
Call Trace:
sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112
sctp_set_owner_w net/sctp/socket.c:131 [inline]
sctp_sendmsg_to_asoc+0x152e/0x2180 net/sctp/socket.c:1865
sctp_sendmsg+0x103b/0x1d30 net/sctp/socket.c:2027
inet_sendmsg+0x99/0xe0 net/ipv4/af_inet.c:821
sock_sendmsg_nosec net/socket.c:703 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:723
This is an use-after-free issue caused by not updating asoc->shkey after
it was replaced in the key list asoc->endpoint_shared_keys, and the old
key was freed.
This patch is to fix by also updating active_key for asoc when old key is
being replaced with a new one. Note that this issue doesn't exist in
sctp_auth_del_key_id(), as it's not allowed to delete the active_key
from the asoc.
Fixes: 1b1e0bc994 ("sctp: add refcnt support for sh_key")
Reported-by: syzbot+b774577370208727d12b@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate IPv4 MTU code the same way it is done in IPv6 to have code
aligned in both address families
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace ip6_dst_mtu_forward with ip6_dst_mtu_maybe_forward and
reuse this code in ip6_mtu. Actually these two functions were
almost duplicates, this change will simplify the maintaince of
mtu calculation code.
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the IOAM inline insertion (only for the host-to-host use case)
which is per-route configured with lightweight tunnels. The target is iproute2
and the patch is ready. It will be posted as soon as this patchset is merged.
Here is an overview:
$ ip -6 ro ad fc00::1/128 encap ioam6 trace type 0x800000 ns 1 size 12 dev eth0
This example configures an IOAM Pre-allocated Trace option attached to the
fc00::1/128 prefix. The IOAM namespace (ns) is 1, the size of the pre-allocated
trace data block is 12 octets (size) and only the first IOAM data (bit 0:
hop_limit + node id) is included in the trace (type) represented as a bitfield.
The reason why the in-transit (IPv6-in-IPv6 encapsulation) use case is not
implemented is explained on the patchset cover.
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Generic Netlink commands to allow userspace to configure IOAM
namespaces and schemas. The target is iproute2 and the patch is ready.
It will be posted as soon as this patchset is merged. Here is an overview:
$ ip ioam
Usage: ip ioam { COMMAND | help }
ip ioam namespace show
ip ioam namespace add ID [ data DATA32 ] [ wide DATA64 ]
ip ioam namespace del ID
ip ioam schema show
ip ioam schema add ID DATA
ip ioam schema del ID
ip ioam namespace set ID schema { ID | none }
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for processing the IOAM Pre-allocated Trace with IPv6,
see [1] and [2]. Introduce a new IPv6 Hop-by-Hop TLV option, see IANA [3].
A new per-interface sysctl is introduced. The value is a boolean to accept (=1)
or ignore (=0, by default) IPv6 IOAM options on ingress for an interface:
- net.ipv6.conf.XXX.ioam6_enabled
Two other sysctls are introduced to define IOAM IDs, represented by an integer.
They are respectively per-namespace and per-interface:
- net.ipv6.ioam6_id
- net.ipv6.conf.XXX.ioam6_id
The value of the first one represents the IOAM ID of the node itself (u32; max
and default value = U32_MAX>>8, due to hop limit concatenation) while the other
represents the IOAM ID of an interface (u16; max and default value = U16_MAX).
Each "ioam6_id" sysctl has a "_wide" equivalent:
- net.ipv6.ioam6_id_wide
- net.ipv6.conf.XXX.ioam6_id_wide
The value of the first one represents the wide IOAM ID of the node itself (u64;
max and default value = U64_MAX>>8, due to hop limit concatenation) while the
other represents the wide IOAM ID of an interface (u32; max and default value
= U32_MAX).
The use of short and wide equivalents is not exclusive, a deployment could
choose to leverage both. For example, net.ipv6.conf.XXX.ioam6_id (short format)
could be an identifier for a physical interface, whereas
net.ipv6.conf.XXX.ioam6_id_wide (wide format) could be an identifier for a
logical sub-interface. Documentation about new sysctls is provided at the end
of this patchset.
Two relativistic hash tables are used: one for IOAM namespaces, the other for
IOAM schemas. A namespace can only have a single active schema and a schema
can only be attached to a single namespace (1:1 relationship).
[1] https://tools.ietf.org/html/draft-ietf-ippm-ioam-ipv6-options
[2] https://tools.ietf.org/html/draft-ietf-ippm-ioam-data
[3] https://www.iana.org/assignments/ipv6-parameters/ipv6-parameters.xhtml#ipv6-parameters-2
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The difference between __switchdev_handle_fdb_del_to_device and
switchdev_handle_del_to_device is that the former takes an extra
orig_dev argument, while the latter starts with dev == orig_dev.
We should recurse into the variant that does not lose the orig_dev along
the way. This is relevant when deleting FDB entries pointing towards a
bridge (dev changes to the lower interfaces, but orig_dev shouldn't).
The addition helper already recurses properly, just the deletion one
doesn't.
Fixes: 8ca07176ab ("net: switchdev: introduce a fanout helper for SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running the self-tests on a KASAN enabled kernel, I observed a
slab-out-of-bounds splat very similar to the one reported in
commit 821bbf79fe ("ipv6: Fix KASAN: slab-out-of-bounds Read in
fib6_nh_flush_exceptions").
We additionally need to take care of fib6_metrics initialization
failure when the caller provides an nh.
The fix is similar, explicitly free the route instead of calling
fib6_info_release on a half-initialized object.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Root in init user namespace can modify /proc/sys/net/ipv4/ip_forward
without CAP_NET_ADMIN, this doesn't follow the principle of
capabilities. For example, let's take a look at netdev_store(),
root can't modify netdev attribute without CAP_NET_ADMIN.
So let's keep the consistency of permission check logic.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tcf_skbmod_act() assumes that packets use Ethernet as their L2
protocol, which is not always the case. As an example, for CAN devices:
$ ip link add dev vcan0 type vcan
$ ip link set up vcan0
$ tc qdisc add dev vcan0 root handle 1: htb
$ tc filter add dev vcan0 parent 1: protocol ip prio 10 \
matchall action skbmod swap mac
Doing the above silently corrupts all the packets. Do not perform skbmod
actions for non-Ethernet packets.
Fixes: 86da71b573 ("net_sched: Introduce skbmod action")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the new fan-out helper for FDB entries installed on the software
bridge, we can install host addresses with the proper refcount on the
CPU port, such that this case:
ip link set swp0 master br0
ip link set swp1 master br0
ip link set swp2 master br0
ip link set swp3 master br0
ip link set br0 address 00:01:02:03:04:05
ip link set swp3 nomaster
works properly and the br0 address remains installed as a host entry
with refcount 3 instead of getting deleted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA has an issue with FDB entries pointing towards the bridge
in the presence of br_fdb_replay() being called at port join and leave
time.
In particular, each bridge port will ask for a replay for the FDB
entries pointing towards the bridge when it joins, and for another
replay when it leaves.
This means that for example, a bridge with 4 switch ports will notify
DSA 4 times of the bridge MAC address.
But if the MAC address of the bridge changes during the normal runtime
of the system, the bridge notifies switchdev [ once ] of the deletion of
the old MAC address as a local FDB towards the bridge, and of the
insertion [ again once ] of the new MAC address as a local FDB.
This is a problem, because DSA keeps the old MAC address as a host FDB
entry with refcount 4 (4 ports asked for it using br_fdb_replay). So the
old MAC address will not be deleted. Additionally, the new MAC address
will only be installed with refcount 1, and when the first switch port
leaves the bridge (leaving 3 others as still members), it will delete
with it the new MAC address of the bridge from the local FDB entries
kept by DSA (because the br_fdb_replay call on deletion will bring the
entry's refcount from 1 to 0).
So the problem, really, is that the number of br_fdb_replay() calls is
not matched with the refcount that a host FDB is offloaded to DSA during
normal runtime.
An elegant way to solve the problem would be to make the switchdev
notification emitted by br_fdb_change_mac_address() result in a host FDB
kept by DSA which has a refcount exactly equal to the number of ports
under that bridge. Then, no matter how many DSA ports join or leave that
bridge, the host FDB entry will always be deleted when there are exactly
zero remaining DSA switch ports members of the bridge.
To implement the proposed solution, we remember that the switchdev
objects and port attributes have some helpers provided by switchdev,
which can be optionally called by drivers:
switchdev_handle_port_obj_{add,del} and switchdev_handle_port_attr_set.
These helpers:
- fan out a switchdev object/attribute emitted for the bridge towards
all the lower interfaces that pass the check_cb().
- fan out a switchdev object/attribute emitted for a bridge port that is
a LAG towards all the lower interfaces that pass the check_cb().
In other words, this is the model we need for the FDB events too:
something that will keep an FDB entry emitted towards a physical port as
it is, but translate an FDB entry emitted towards the bridge into N FDB
entries, one per physical port.
Of course, there are many differences between fanning out a switchdev
object (VLAN) on 3 lower interfaces of a LAG and fanning out an FDB
entry on 3 lower interfaces of a LAG. Intuitively, an FDB entry towards
a LAG should be treated specially, because FDB entries are unicast, we
can't just install the same address towards 3 destinations. It is
imaginable that drivers might want to treat this case specifically, so
create some methods for this case and do not recurse into the LAG lower
ports, just the bridge ports.
DSA also listens for FDB entries on "foreign" interfaces, aka interfaces
bridged with us which are not part of our hardware domain: think an
Ethernet switch bridged with a Wi-Fi AP. For those addresses, DSA
installs host FDB entries. However, there we have the same problem
(those host FDB entries are installed with a refcount of only 1) and an
even bigger one which we did not have with FDB entries towards the
bridge:
br_fdb_replay() is currently not called for FDB entries on foreign
interfaces, just for the physical port and for the bridge itself.
So when DSA sniffs an address learned by the software bridge towards a
foreign interface like an e1000 port, and then that e1000 leaves the
bridge, DSA remains with the dangling host FDB address. That will be
fixed separately by replaying all FDB entries and not just the ones
towards the port and the bridge.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a bit difficult to understand what DSA checks when it tries to
avoid installing dynamically learned addresses on foreign interfaces as
local host addresses, so create a generic switchdev helper that can be
reused and is generally more readable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The big problem which mandates cross-chip notifiers for tag_8021q is
this:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
When the user runs:
ip link add br0 type bridge
ip link set sw0p0 master br0
ip link set sw2p0 master br0
It doesn't work.
This is because dsa_8021q_crosschip_bridge_join() assumes that "ds" and
"other_ds" are at most 1 hop away from each other, so it is sufficient
to add the RX VLAN of {ds, port} into {other_ds, other_port} and vice
versa and presto, the cross-chip link works. When there is another
switch in the middle, such as in this case switch 1 with its DSA links
sw1p3 and sw1p4, somebody needs to tell it about these VLANs too.
Which is exactly why the problem is quadratic: when a port joins a
bridge, for each port in the tree that's already in that same bridge we
notify a tag_8021q VLAN addition of that port's RX VLAN to the entire
tree. It is a very complicated web of VLANs.
It must be mentioned that currently we install tag_8021q VLANs on too
many ports (DSA links - to be precise, on all of them). For example,
when sw2p0 joins br0, and assuming sw1p0 was part of br0 too, we add the
RX VLAN of sw2p0 on the DSA links of switch 0 too, even though there
isn't any port of switch 0 that is a member of br0 (at least yet).
In theory we could notify only the switches which sit in between the
port joining the bridge and the port reacting to that bridge_join event.
But in practice that is impossible, because of the way 'link' properties
are described in the device tree. The DSA bindings require DT writers to
list out not only the real/physical DSA links, but in fact the entire
routing table, like for example switch 0 above will have:
sw0p3: port@3 {
link = <&sw1p4 &sw2p4>;
};
This was done because:
/* TODO: ideally DSA ports would have a single dp->link_dp member,
* and no dst->rtable nor this struct dsa_link would be needed,
* but this would require some more complex tree walking,
* so keep it stupid at the moment and list them all.
*/
but it is a perfect example of a situation where too much information is
actively detrimential, because we are now in the position where we
cannot distinguish a real DSA link from one that is put there to avoid
the 'complex tree walking'. And because DT is ABI, there is not much we
can change.
And because we do not know which DSA links are real and which ones
aren't, we can't really know if DSA switch A is in the data path between
switches B and C, in the general case.
So this is why tag_8021q RX VLANs are added on all DSA links, and
probably why it will never change.
On the other hand, at least the number of additions/deletions is well
balanced, and this means that once we implement reference counting at
the cross-chip notifier level a la fdb/mdb, there is absolutely zero
need for a struct dsa_8021q_crosschip_link, it's all self-managing.
In fact, with the tag_8021q notifiers emitted from the bridge join
notifiers, it becomes so generic that sja1105 does not need to do
anything anymore, we can just delete its implementation of the
.crosschip_bridge_{join,leave} methods.
Among other things we can simply delete is the home-grown implementation
of sja1105_notify_crosschip_switches(). The reason why that is wrong is
because it is not quadratic - it only covers remote switches to which we
have a cross-chip bridging link and that does not cover in-between
switches. This deletion is part of the same patch because sja1105 used
to poke deep inside the guts of the tag_8021q context in order to do
that. Because the cross-chip links went away, so needs the sja1105 code.
Last but not least, dsa_8021q_setup_port() is simplified (and also
renamed). Because our TAG_8021Q_VLAN_ADD notifier is designed to react
on the CPU port too, the four dsa_8021q_vid_apply() calls:
- 1 for RX VLAN on user port
- 1 for the user port's RX VLAN on the CPU port
- 1 for TX VLAN on user port
- 1 for the user port's TX VLAN on the CPU port
now get squashed into only 2 notifier calls via
dsa_port_tag_8021q_vlan_add.
And because the notifiers to add and to delete a tag_8021q VLAN are
distinct, now we finally break up the port setup and teardown into
separate functions instead of relying on a "bool enabled" flag which
tells us what to do. Arguably it should have been this way from the
get go.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been at least one wasted opportunity for tag_8021q to be used
by a driver:
https://patchwork.ozlabs.org/project/netdev/patch/20200710113611.3398-3-kurt@linutronix.de/#2484272
because of a design decision: the declared purpose of tag_8021q is to
offer source port/switch identification for a tagging driver for packets
coming from a switch with no hardware DSA tagging support. It is not
intended to provide VLAN-based port isolation, because its first user,
sja1105, had another mechanism for bridging domain isolation, the L2
Forwarding Table. So even if 2 ports are in the same VLAN but they are
separated via the L2 Forwarding Table, they will not communicate with
one another. The L2 Forwarding Table is managed by the
sja1105_bridge_join() and sja1105_bridge_leave() methods.
As a consequence, today tag_8021q does not bother too much with hooking
into .port_bridge_join() and .port_bridge_leave() because that would
introduce yet another degree of freedom, it just iterates statically
through all ports of a switch and adds the RX VLAN of one port to all
the others. In this way, whenever .port_bridge_join() is called,
bridging will magically work because the RX VLANs are already installed
everywhere they need to be.
This is not to say that the reason for the change in this patch is to
satisfy the hellcreek and similar use cases, that is merely a nice side
effect. Instead it is to make sja1105 cross-chip links work properly
over a DSA link.
For context, sja1105 today supports a degenerate form of cross-chip
bridging, where the switches are interconnected through their CPU ports
("disjoint trees" topology). There is some code which has been
generalized into dsa_8021q_crosschip_link_{add,del}, but it is not
enough, and frankly it is impossible to build upon that.
Real multi-switch DSA trees, like daisy chains or H trees, which have
actual DSA links, do not work.
The problem is that sja1105 is unlike mv88e6xxx, and does not have a PVT
for cross-chip bridging, which is a table by which the local switch can
select the forwarding domain for packets from a certain ingress switch
ID and source port. The sja1105 switches cannot parse their own DSA
tags, because, well, they don't really have support for DSA tags, it's
all VLANs.
So to make something like cross-chip bridging between sw0p0 and sw1p0 to
work over the sw0p3/sw1p3 DSA link to work with sja1105 in the topology
below:
| |
sw0p0 sw0p1 sw0p2 sw0p3 sw1p3 sw1p2 sw1p1 sw1p0
[ user ] [ user ] [ cpu ] [ dsa ] ---- [ dsa ] [ cpu ] [ user ] [ user ]
we need to ask ourselves 2 questions:
(1) how should the L2 Forwarding Table be managed?
(2) how should the VLAN Lookup Table be managed?
i.e. what should prevent packets from going to unwanted ports?
Since as mentioned, there is no PVT, the L2 Forwarding Table only
contains forwarding rules for local ports. So we can say "all user ports
are allowed to forward to all CPU ports and all DSA links".
If we allow forwarding to DSA links unconditionally, this means we must
prevent forwarding using the VLAN Lookup Table. This is in fact
asymmetric with what we do for tag_8021q on ports local to the same
switch, and it matters because now that we are making tag_8021q a core
DSA feature, we need to hook into .crosschip_bridge_join() to add/remove
the tag_8021q VLANs. So for symmetry it makes sense to manage the VLANs
for local forwarding in the same way as cross-chip forwarding.
Note that there is a very precise reason why tag_8021q hooks into
dsa_switch_bridge_join() which acts at the cross-chip notifier level,
and not at a higher level such as dsa_port_bridge_join(). We need to
install the RX VLAN of the newly joining port into the VLAN table of all
the existing ports across the tree that are part of the same bridge, and
the notifier already does the iteration through the switches for us.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, setting up tag_8021q is a 2-step operation for a driver,
first the context structure needs to be created, then the VLANs need to
be installed on the ports. A similar thing is true for teardown.
Merge the 2 steps into the register/unregister methods, to be as
transparent as possible for the driver as to what tag_8021q does behind
the scenes. This also gets rid of the funny "bool setup == true means
setup, == false means teardown" API that tag_8021q used to expose.
Note that dsa_tag_8021q_register() must be called at least in the
.setup() driver method and never earlier (like in the driver probe
function). This is because the DSA switch tree is not initialized at
probe time, and the cross-chip notifiers will not work.
For symmetry with .setup(), the unregister method should be put in
.teardown().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make tag_8021q a more central element of DSA and move the 2 driver
specific operations outside of struct dsa_8021q_context (which is
supposed to hold dynamic data and not really constant function
pointers).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The basic problem description is as follows:
Be there 3 switches in a daisy chain topology:
|
sw0p0 sw0p1 sw0p2 sw0p3 sw0p4
[ user ] [ user ] [ user ] [ dsa ] [ cpu ]
|
+---------+
|
sw1p0 sw1p1 sw1p2 sw1p3 sw1p4
[ user ] [ user ] [ user ] [ dsa ] [ dsa ]
|
+---------+
|
sw2p0 sw2p1 sw2p2 sw2p3 sw2p4
[ user ] [ user ] [ user ] [ user ] [ dsa ]
The CPU will not be able to ping through the user ports of the
bottom-most switch (like for example sw2p0), simply because tag_8021q
was not coded up for this scenario - it has always assumed DSA switch
trees with a single switch.
To add support for the topology above, we must admit that the RX VLAN of
sw2p0 must be added on some ports of switches 0 and 1 as well. This is
in fact a textbook example of thing that can use the cross-chip notifier
framework that DSA has set up in switch.c.
There is only one problem: core DSA (switch.c) is not able right now to
make the connection between a struct dsa_switch *ds and a struct
dsa_8021q_context *ctx. Right now, it is drivers who call into
tag_8021q.c and always provide a struct dsa_8021q_context *ctx pointer,
and tag_8021q.c calls them back with the .tag_8021q_vlan_{add,del}
methods.
But with cross-chip notifiers, it is possible for tag_8021q to call
drivers without drivers having ever asked for anything. A good example
is right above: when sw2p0 wants to set itself up for tag_8021q,
the .tag_8021q_vlan_add method needs to be called for switches 1 and 0,
so that they transport sw2p0's VLANs towards the CPU without dropping
them.
So instead of letting drivers manage the tag_8021q context, add a
tag_8021q_ctx pointer inside of struct dsa_switch, which will be
populated when dsa_tag_8021q_register() returns success.
The patch is fairly long-winded because we are partly reverting commit
5899ee367a ("net: dsa: tag_8021q: add a context structure") which made
the driver-facing tag_8021q API use "ctx" instead of "ds". Now that we
can access "ctx" directly from "ds", this is no longer needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming patches will add tag_8021q related logic to switch.c and
port.c, in order to allow it to make use of cross-chip notifiers.
In addition, a struct dsa_8021q_context *ctx pointer will be added to
struct dsa_switch.
It seems fairly low-reward to #ifdef the *ctx from struct dsa_switch and
to provide shim implementations of the entire tag_8021q.c calling
surface (not even clear what to do about the tag_8021q cross-chip
notifiers to avoid compiling them). The runtime overhead for switches
which don't use tag_8021q is fairly small because all helpers will check
for ds->tag_8021q_ctx being a NULL pointer and stop there.
So let's make it part of dsa_core.o.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of moving tag_8021q to core DSA, move all initialization
and teardown related to tag_8021q which is currently done by drivers in
2 functions called "register" and "unregister". These will gather more
functionality in future patches, which will better justify the chosen
naming scheme.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %pe to give the user a string holding the error code instead of just
a number.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the tag_8021q code has been taken out of sja1105, which uses
"rc" for its return code variables, whereas the DSA core uses "err".
Change tag_8021q for consistency.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply put, the best-effort VLAN filtering mode relied on VLAN retagging
from a bridge VLAN towards a tag_8021q sub-VLAN in order to be able to
decode the source port in the tagger, but the VLAN retagging
implementation inside the sja1105 chips is not the best and we were
relying on marginal operating conditions.
The most notable limitation of the best-effort VLAN filtering mode is
its incapacity to treat this case properly:
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp4 master br0
bridge vlan del dev swp4 vid 1
bridge vlan add dev swp4 vid 1 pvid
When sending an untagged packet through swp2, the expectation is for it
to be forwarded to swp4 as egress-tagged (so it will contain VLAN ID 1
on egress). But the switch will send it as egress-untagged.
There was an attempt to fix this here:
https://patchwork.kernel.org/project/netdevbpf/patch/20210407201452.1703261-2-olteanv@gmail.com/
but it failed miserably because it broke PTP RX timestamping, in a way
that cannot be corrected due to hardware issues related to VLAN
retagging.
So with either PTP broken or pushing VLAN headers on egress for untagged
packets being broken, the sad reality is that the best-effort VLAN
filtering code is broken. Delete it.
Note that this means there will be a temporary loss of functionality in
this driver until it is replaced with something better (network stack
RX/TX capability for "mode 2" as described in
Documentation/networking/dsa/sja1105.rst, the "port under VLAN-aware
bridge" case). We simply cannot keep this code until that driver rework
is done, it is super bloated and tangled with tag_8021q.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
