pfifo_fast_enqueue has this check:
if (skb_queue_len(list) < qdisc_dev(qdisc)->tx_queue_len) {
which allows each band to enqueue upto tx_queue_len skbs for a
total of 3*tx_queue_len skbs. I am not sure if this was the
intention of limiting in qdisc.
Patch compiled and 32 simultaneous netperf testing ran fine. Also:
# tc -s qdisc show dev eth2
qdisc pfifo_fast 0: root bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
Sent 16835026752 bytes 373116 pkt (dropped 0, overlimits 0 requeues 25)
rate 0bit 0pps backlog 0b 0p requeues 25
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain a per-qdisc bitmap for pfifo_fast giving availability
of skbs for each band. This allows faster lookup for a skb when
there are no high priority skbs. Also, it helps in (rare) cases
when there are no skbs on the list, where an immediate lookup is
faster than iterating through the three bands.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_queue_xmit enqueue's a skb and calls qdisc_run which
dequeue's the skb and xmits it. In most cases, the skb that
is enqueue'd is the same one that is dequeue'd (unless the
queue gets stopped or multiple cpu's write to the same queue
and ends in a race with qdisc_run). For default qdiscs, we
can remove the redundant enqueue/dequeue and simply xmit the
skb since the default qdisc is work-conserving.
The patch uses a new flag - TCQ_F_CAN_BYPASS to identify the
default fast queue. The controversial part of the patch is
incrementing qlen when a skb is requeued - this is to avoid
checks like the second line below:
+ } else if ((q->flags & TCQ_F_CAN_BYPASS) && !qdisc_qlen(q) &&
>> !q->gso_skb &&
+ !test_and_set_bit(__QDISC_STATE_RUNNING, &q->state)) {
Results of a 2 hour testing for multiple netperf sessions (1,
2, 4, 8, 12 sessions on a 4 cpu system-X). The BW numbers are
aggregate Mb/s across iterations tested with this version on
System-X boxes with Chelsio 10gbps cards:
----------------------------------
Size | ORG BW NEW BW |
----------------------------------
128K | 156964 159381 |
256K | 158650 162042 |
----------------------------------
Changes from ver1:
1. Move sch_direct_xmit declaration from sch_generic.h to
pkt_sched.h
2. Update qdisc basic statistics for direct xmit path.
3. Set qlen to zero in qdisc_reset.
4. Changed some function names to more meaningful ones.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct net_device trans_start field is a hot spot on SMP and high performance
devices, particularly multi queues ones, because every transmitter dirties
it. Is main use is tx watchdog and bonding alive checks.
But as most devices dont use NETIF_F_LLTX, we have to lock
a netdev_queue before calling their ndo_start_xmit(). So it makes
sense to move trans_start from net_device to netdev_queue. Its update
will occur on a already present (and in exclusive state) cache line, for
free.
We can do this transition smoothly. An old driver continue to
update dev->trans_start, while an updated one updates txq->trans_start.
Further patches could also put tx_bytes/tx_packets counters in
netdev_queue to avoid dirtying dev->stats (vlan device comes to mind)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the network device internal API to move adminstrative
operations out of the network device structure and into a separate structure.
This patch involves some hackery to maintain compatablity between the
new and old model, so all 300+ drivers don't have to be changed at once.
For drivers that aren't converted yet, the netdevice_ops virt function list
still resides in the net_device structure. For old protocols, the new
net_device_ops are copied out to the old net_device pointers.
After the transistion is completed the nag message can be changed to
an WARN_ON, and the compatiablity code can be made configurable.
Some function pointers aren't moved:
* destructor can't be in net_device_ops because
it may need to be referenced after the module is unloaded.
* neighbor setup is manipulated in a couple of places that need special
consideration
* hard_start_xmit is in the fast path for transmit.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several device drivers try to do things like netif_carrier_off()
before register_netdev() is invoked. This is bogus, but too many
drivers do this to fix them all up in one go.
Reported-by: Folkert van Heusden <folkert@vanheusden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After implementing qdisc->ops->peek() and changing sch_netem into
classless qdisc there are no more qdisc->ops->requeue() users. This
patch removes this method with its wrappers (qdisc_requeue()), and
also unused qdisc->requeue structure. There are a few minor fixes of
warnings (htb_enqueue()) and comments btw.
The idea to kill ->requeue() and a similar patch were first developed
by David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since gso_skb is re-used for qdisc_peek_dequeued(), and this skb is
counted in the qdisc->q.qlen, it has to be kfreed during qdisc_reset()
when qlen is zeroed.
With help from David S. Miller <davem@davemloft.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After these commands:
# modprobe sch_teql
# tc qdisc add dev eth0 root teql0
# tc qdisc del dev eth0 root
we get an oops in teql_destroy() when spin_lock is taken from a null
qdisc_sleeping pointer. It's because at the moment teql0 dev haven't
been activated yet, and a qdisc_root_sleeping() is pointing to noop
qdisc's netdev_queue with qdisc_sleeping uninitialized. This patch
fixes this both for noop and noqueue netdev_queues to avoid similar
problems in the future.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last change of requeuing there is no info about such
incidents in tc stats. This patch updates the counter, but we should
consider this should differ from previous stats because of additional
checks preventing to repeat this. On the other hand, previous stats
didn't include requeuing of gso_segmented skbs.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc->requeue was planned to universally replace all requeuing code,
but at the top level we never requeue more than one skb, so qdisc->
gso_skb is enough for this. qdisc->requeue would be used on the lower
levels only for one level deep requeuing (like in sch_hfsc) after
finishing all the changes.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Cliburn noticed and diagnosed a bug triggered in
dev_gso_skb_destructor() after last change from qdisc->gso_skb
to qdisc->requeue list. Since gso_segmented skbs can't be queued
to another list this patch brings back qdisc->gso_skb for them.
Reported-by: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check in dequeue_skb() the state of tx_queue for requeued skb to save
on locking and re-requeuing, and possibly remove the current check in
qdisc_run(). Based on the idea of Alexander Duyck.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to call into the complicated qdiscs
just to remember the last SKB where we found the device
blocked.
The SKB is outside of the qdiscs realm at this point.
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch turns the netdev timeout WARN_ON_ONCE() into a WARN_ONCE(),
so that the device and driver names are inside the warning message.
This helps automated tools like kerneloops.org to collect the data
and do statistics, as well as making it more likely that humans
cut-n-paste the important message as part of a bugreport.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pointers are RCU protected, so proper primitives should be used.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since some qdiscs call qdisc_tree_decrease_qlen() (so qdisc_lookup())
without rtnl_lock(), adding and deleting from a qdisc list needs
additional locking. This patch adds global spinlock qdisc_list_lock
and wrapper functions for modifying the list. It is considered as a
temporary solution until hfsc_dequeue(), netem_dequeue() and
tbf_dequeue() (or qdisc_tree_decrease_qlen()) are redone.
With feedback from Herbert Xu and David S. Miller.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon reports by Denys Fedoryshchenko, and feedback
and help from Jarek Poplawski and Herbert Xu.
We always either:
1) Never made an external reference to this qdisc.
or
2) Did a dev_deactivate() which purged all asynchronous
references.
So do not lock the qdisc when we call qdisc_destroy(),
it's illegal anyways as when we drop the lock this is
free'd memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now kill them synchronously with all of the
previous dev_deactivate() cures.
This makes netdev destruction and shutdown saner as
the qdiscs hold references to the device.
Signed-off-by: David S. Miller <davem@davemloft.net>
The condition under which the previous qdisc has no more references
after we've attached &noop_qdisc is that both RUNNING and SCHED
are both seen clear while holding the root lock.
So just make specifically that check in the polling loop, instead
of this overly complex "check without then check with lock held"
sequence.
Signed-off-by: David S. Miller <davem@davemloft.net>
This new state lets dev_deactivate() mark a qdisc as having been
deactivated.
dev_queue_xmit() and ing_filter() check for this bit and do not
try to process the qdisc if the bit is set.
dev_deactivate() polls the qdisc after setting the bit, waiting
for both __QDISC_STATE_RUNNING and __QDISC_STATE_SCHED to clear.
This isn't perfect yet, but subsequent changesets will make it so.
This part is just one piece of the puzzle.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon discussions with Jarek P. and Herbert Xu.
First, we're testing the wrong qdisc. We just reset the device
queue qdiscs to &noop_qdisc and checking it's state is completely
pointless here.
We want to wait until the previous qdisc that was sitting at
the ->qdisc pointer is not busy any more. And that would be
->qdisc_sleeping.
Because of how we propagate the samples qdisc pointer down into
qdisc_run and friends via per-cpu ->output_queue and netif_schedule,
we have to wait also for the __QDISC_STATE_SCHED bit to clear as
well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon a bug report by Jeff Kirsher.
Don't use qdisc_root_lock() in these cases as the root
qdisc could have been changed, and we'd thus lock the
wrong object.
Tested by Emil S Tantilov who confirms that this seems
to fix the problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for multiple TX queues were added, the
netif_tx_lock() routines we converted to iterate over
all TX queues and grab each queue's spinlock.
This causes heartburn for lockdep and it's not a healthy
thing to do with lots of TX queues anyways.
So modify this to use a top-level lock and a "frozen"
state for the individual TX queues.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug report from Steven Jan Springl:
Issuing the following command causes a kernel oops:
tc qdisc add dev eth0 handle ffff: ingress
The problem mostly stems from all of the special case handling of
ingress qdiscs.
So, to fix this, do the grafting operation the same way we do for TX
qdiscs. Which means that dev_activate() and dev_deactivate() now do
the "qdisc_sleeping <--> qdisc" transitions on dev->rx_queue too.
Future simplifications are possible now, mainly because it is
impossible for dev_queue->{qdisc,qdisc_sleeping} to be NULL. There
are NULL checks all over to handle the ingress qdisc special case
that used to exist before this commit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.
I could make at least one BUILD_BUG_ON conversion.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Dave:
This patch adds a function to get the driver name from a struct net_device,
and consequently uses this in the watchdog timeout handler to print as
part of the message.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a0c80b80e0.
After discussions with Jamal and Herbert on netdev, we should
provide at least minimal prioritization at the qdisc level
even in multiqueue situations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed unused variable 'skb' in the dev_deactivate_queue function
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stab bits can't be referenced uniless the full
packet scheduler layer is enabled.
Reported by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add size table functions for qdiscs and calculate packet size in
qdisc_enqueue().
Based on patch by Patrick McHardy
http://marc.info/?l=linux-netdev&m=115201979221729&w=2
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like noop_qdisc, it needs a dummy backpointer and
explicit qdisc->q.lock initialization.
Based upon a report by Stephen Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Idea is from Patrick McHardy.
Instead of managing the list of qdiscs on the device level, manage it
in the root qdisc of a netdev_queue. This solves all kinds of
visibility issues during qdisc destruction.
The way to iterate over all qdiscs of a netdev_queue is to visit
the netdev_queue->qdisc, and then traverse it's list.
The only special case is to ignore builting qdiscs at the root when
dumping or doing a qdisc_lookup(). That was not needed previously
because builtin qdiscs were not added to the device's qdisc_list.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of 'pfifo_fast' we have just plain 'fifo_fast'.
No priority queues, just a straight FIFO.
This is necessary in order to legally have a seperate
qdisc per queue in multi-TX-queue setups, and thus get
full parallelization.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows less strict control of access to the qdisc attached to a
netdev_queue. It is even allowed to enqueue into a qdisc which is
in the process of being destroyed. The RCU handler will toss out
those packets.
We will need this to handle sharing of a qdisc amongst multiple
TX queues. In such a setup the lock has to be shared, so will
be inside of the qdisc itself. At which point the netdev_queue
lock cannot be used to hard synchronize access to the ->qdisc
pointer.
One operation we have to keep inside of qdisc_destroy() is the list
deletion. It is the only piece of state visible after the RCU quiesce
period, so we have to undo it early and under the appropriate locking.
The operations in the RCU handler do not need any looking because the
qdisc tree is no longer visible to anything at that point.
Signed-off-by: David S. Miller <davem@davemloft.net>
We are registering the device, there is no way anyone can get
at this object's qdiscs yet in any meaningful way.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have shared qdiscs, packets come out of the qdiscs
for multiple transmit queues.
Therefore it doesn't make any sense to schedule the transmit
queue when logically we cannot know ahead of time the TX
queue of the SKB that the qdisc->dequeue() will give us.
Just for sanity I added a BUG check to make sure we never
get into a state where the noop_qdisc is scheduled.
Signed-off-by: David S. Miller <davem@davemloft.net>
When code wants to lock the qdisc tree state, the logic
operation it's doing is locking the top-level qdisc that
sits of the root of the netdev_queue.
Add qdisc_root_lock() to represent this and convert the
easiest cases.
In order for this to work out in all cases, we have to
hook up the noop_qdisc to a dummy netdev_queue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it is associated with a netdev_queue, but when we have
qdisc sharing that no longer makes any sense.
Signed-off-by: David S. Miller <davem@davemloft.net>
We liberate any dangling gso_skb during qdisc destruction.
It really only matters for the root qdisc. But when qdiscs
can be shared by multiple netdev_queue objects, we can't
have the gso_skb in the netdev_queue any more.
Signed-off-by: David S. Miller <davem@davemloft.net>
This effectively "flips the switch" by making the core networking
and multiqueue-aware drivers use the new TX multiqueue structures.
Non-multiqueue drivers need no changes. The interfaces they use such
as netif_stop_queue() degenerate into an operation on TX queue zero.
So everything "just works" for them.
Code that really wants to do "X" to all TX queues now invokes a
routine that does so, such as netif_tx_wake_all_queues(),
netif_tx_stop_all_queues(), etc.
pktgen and netpoll required a little bit more surgery than the others.
In particular the pktgen changes, whilst functional, could be largely
improved. The initial check in pktgen_xmit() will sometimes check the
wrong queue, which is mostly harmless. The thing to do is probably to
invoke fill_packet() earlier.
The bulk of the netpoll changes is to make the code operate solely on
the TX queue indicated by by the SKB queue mapping.
Setting of the SKB queue mapping is entirely confined inside of
net/core/dev.c:dev_pick_tx(). If we end up needing any kind of
special semantics (drops, for example) it will be implemented here.
Finally, we now have a "real_num_tx_queues" which is where the driver
indicates how many TX queues are actually active.
With IGB changes from Jeff Kirsher.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_netdev_mq() now allocates an array of netdev_queue
structures for TX, based upon the queue_count argument.
Furthermore, all accesses to the TX queues are now vectored
through the netdev_get_tx_queue() and netdev_for_each_tx_queue()
interfaces. This makes it easy to grep the tree for all
things that want to get to a TX queue of a net device.
Problem spots which are not really multiqueue aware yet, and
only work with one queue, can easily be spotted by grepping
for all netdev_get_tx_queue() calls that pass in a zero index.
Signed-off-by: David S. Miller <davem@davemloft.net>
Krishna Kumar