Currently if we add only constant values to pointers we can fully
validate the alignment, and properly check if we need to reject the
program on !CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS architectures.
However, once an unknown value is introduced we only allow byte sized
memory accesses which is too restrictive.
Add logic to track the known minimum alignment of register values,
and propagate this state into registers containing pointers.
The most common paradigm that makes use of this new logic is computing
the transport header using the IP header length field. For example:
struct ethhdr *ep = skb->data;
struct iphdr *iph = (struct iphdr *) (ep + 1);
struct tcphdr *th;
...
n = iph->ihl;
th = ((void *)iph + (n * 4));
port = th->dest;
The existing code will reject the load of th->dest because it cannot
validate that the alignment is at least 2 once "n * 4" is added the
the packet pointer.
In the new code, the register holding "n * 4" will have a reg->min_align
value of 4, because any value multiplied by 4 will be at least 4 byte
aligned. (actually, the eBPF code emitted by the compiler in this case
is most likely to use a shift left by 2, but the end result is identical)
At the critical addition:
th = ((void *)iph + (n * 4));
The register holding 'th' will start with reg->off value of 14. The
pointer addition will transform that reg into something that looks like:
reg->aux_off = 14
reg->aux_off_align = 4
Next, the verifier will look at the th->dest load, and it will see
a load offset of 2, and first check:
if (reg->aux_off_align % size)
which will pass because aux_off_align is 4. reg_off will be computed:
reg_off = reg->off;
...
reg_off += reg->aux_off;
plus we have off==2, and it will thus check:
if ((NET_IP_ALIGN + reg_off + off) % size != 0)
which evaluates to:
if ((NET_IP_ALIGN + 14 + 2) % size != 0)
On strict alignment architectures, NET_IP_ALIGN is 2, thus:
if ((2 + 14 + 2) % size != 0)
which passes.
These pointer transformations and checks work regardless of whether
the constant offset or the variable with known alignment is added
first to the pointer register.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Pull networking fixes from David Miller:
1) Fix multiqueue in stmmac driver on PCI, from Andy Shevchenko.
2) cdc_ncm doesn't actually fully zero out the padding area is
allocates on TX, from Jim Baxter.
3) Don't leak map addresses in BPF verifier, from Daniel Borkmann.
4) If we randomize TCP timestamps, we have to do it everywhere
including SYN cookies. From Eric Dumazet.
5) Fix "ethtool -S" crash in aquantia driver, from Pavel Belous.
6) Fix allocation size for ntp filter bitmap in bnxt_en driver, from
Dan Carpenter.
7) Add missing memory allocation return value check to DSA loop driver,
from Christophe Jaillet.
8) Fix XDP leak on driver unload in qed driver, from Suddarsana Reddy
Kalluru.
9) Don't inherit MC list from parent inet connection sockets, another
syzkaller spotted gem. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
dccp/tcp: do not inherit mc_list from parent
qede: Split PF/VF ndos.
qed: Correct doorbell configuration for !4Kb pages
qed: Tell QM the number of tasks
qed: Fix VF removal sequence
qede: Fix XDP memory leak on unload
net/mlx4_core: Reduce harmless SRIOV error message to debug level
net/mlx4_en: Avoid adding steering rules with invalid ring
net/mlx4_en: Change the error print to debug print
drivers: net: wimax: i2400m: i2400m-usb: Use time_after for time comparison
DECnet: Use container_of() for embedded struct
Revert "ipv4: restore rt->fi for reference counting"
net: mdio-mux: bcm-iproc: call mdiobus_free() in error path
net: ethernet: ti: cpsw: adjust cpsw fifos depth for fullduplex flow control
ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf
net: cdc_ncm: Fix TX zero padding
stmmac: pci: split out common_default_data() helper
stmmac: pci: RX queue routing configuration
stmmac: pci: TX and RX queue priority configuration
stmmac: pci: set default number of rx and tx queues
...
Pull misc vfs updates from Al Viro:
"Assorted bits and pieces from various people. No common topic in this
pile, sorry"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs/affs: add rename exchange
fs/affs: add rename2 to prepare multiple methods
Make stat/lstat/fstatat pass AT_NO_AUTOMOUNT to vfs_statx()
fs: don't set *REFERENCED on single use objects
fs: compat: Remove warning from COMPATIBLE_IOCTL
remove pointless extern of atime_need_update_rcu()
fs: completely ignore unknown open flags
fs: add a VALID_OPEN_FLAGS
fs: remove _submit_bh()
fs: constify tree_descr arrays passed to simple_fill_super()
fs: drop duplicate header percpu-rwsem.h
fs/affs: bugfix: Write files greater than page size on OFS
fs/affs: bugfix: enable writes on OFS disks
fs/affs: remove node generation check
fs/affs: import amigaffs.h
fs/affs: bugfix: make symbolic links work again
__vmalloc* allows users to provide gfp flags for the underlying
allocation. This API is quite popular
$ git grep "=[[:space:]]__vmalloc\|return[[:space:]]*__vmalloc" | wc -l
77
The only problem is that many people are not aware that they really want
to give __GFP_HIGHMEM along with other flags because there is really no
reason to consume precious lowmemory on CONFIG_HIGHMEM systems for pages
which are mapped to the kernel vmalloc space. About half of users don't
use this flag, though. This signals that we make the API unnecessarily
too complex.
This patch simply uses __GFP_HIGHMEM implicitly when allocating pages to
be mapped to the vmalloc space. Current users which add __GFP_HIGHMEM
are simplified and drop the flag.
Link: http://lkml.kernel.org/r/20170307141020.29107-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: Cristopher Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch fixes two things at once:
1) It checks the env->allow_ptr_leaks and only prints the map address to
the log if we have the privileges to do so, otherwise it just dumps 0
as we would when kptr_restrict is enabled on %pK. Given the latter is
off by default and not every distro sets it, I don't want to rely on
this, hence the 0 by default for unprivileged.
2) Printing of ldimm64 in the verifier log is currently broken in that
we don't print the full immediate, but only the 32 bit part of the
first insn part for ldimm64. Thus, fix this up as well; it's okay to
access, since we verified all ldimm64 earlier already (including just
constants) through replace_map_fd_with_map_ptr().
Fixes: 1be7f75d16 ("bpf: enable non-root eBPF programs")
Fixes: cbd3570086 ("bpf: verifier (add ability to receive verification log)")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
llvm 4.0 and above generates the code like below:
....
440: (b7) r1 = 15
441: (05) goto pc+73
515: (79) r6 = *(u64 *)(r10 -152)
516: (bf) r7 = r10
517: (07) r7 += -112
518: (bf) r2 = r7
519: (0f) r2 += r1
520: (71) r1 = *(u8 *)(r8 +0)
521: (73) *(u8 *)(r2 +45) = r1
....
and the verifier complains "R2 invalid mem access 'inv'" for insn #521.
This is because verifier marks register r2 as unknown value after #519
where r2 is a stack pointer and r1 holds a constant value.
Teach verifier to recognize "stack_ptr + imm" and
"stack_ptr + reg with const val" as valid stack_ptr with new offset.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes rightfully spotted that the bpf_lock doesn't need to be
irqsave variant. We never perform any such updates where this
would be necessary (neither right now nor in future), therefore
relax this further.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
simple_fill_super() is passed an array of tree_descr structures which
describe the files to create in the filesystem's root directory. Since
these arrays are never modified intentionally, they should be 'const' so
that they are placed in .rodata and benefit from memory protection.
This patch updates the function signature and all users, and also
constifies tree_descr.name.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When iterating through a map, we need to find a key that does not exist
in the map so map_get_next_key will give us the first key of the map.
This often requires a lot of guessing in production systems.
This patch makes map_get_next_key return the first key when the key
pointer in the parameter is NULL.
Signed-off-by: Teng Qin <qinteng@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that also the last in-tree user of the xdp_adjust_head bit has
been removed, we can remove the flag from struct bpf_prog altogether.
This, at the same time, also makes sure that any future driver for
XDP comes with bpf_xdp_adjust_head() support right away.
A rejection based on this flag would also mean that tail calls
couldn't be used with such driver as per c2002f9837 ("bpf: fix
checking xdp_adjust_head on tail calls") fix, thus lets not allow
for it in the first place.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 17bedab272 ("bpf: xdp: Allow head adjustment in XDP prog")
added the xdp_adjust_head bit to the BPF prog in order to tell drivers
that the program that is to be attached requires support for the XDP
bpf_xdp_adjust_head() helper such that drivers not supporting this
helper can reject the program. There are also drivers that do support
the helper, but need to check for xdp_adjust_head bit in order to move
packet metadata prepended by the firmware away for making headroom.
For these cases, the current check for xdp_adjust_head bit is insufficient
since there can be cases where the program itself does not use the
bpf_xdp_adjust_head() helper, but tail calls into another program that
uses bpf_xdp_adjust_head(). As such, the xdp_adjust_head bit is still
set to 0. Since the first program has no control over which program it
calls into, we need to assume that bpf_xdp_adjust_head() helper is used
upon tail calls. Thus, for the very same reasons in cb_access, set the
xdp_adjust_head bit to 1 when the main program uses tail calls.
Fixes: 17bedab272 ("bpf: xdp: Allow head adjustment in XDP prog")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ff936a04e5 ("bpf: fix cb access in socket filter programs")
added a fix for socket filter programs such that in i) AF_PACKET the
20 bytes of skb->cb[] area gets zeroed before use in order to not leak
data, and ii) socket filter programs attached to TCP/UDP sockets need
to save/restore these 20 bytes since they are also used by protocol
layers at that time.
The problem is that bpf_prog_run_save_cb() and bpf_prog_run_clear_cb()
only look at the actual attached program to determine whether to zero
or save/restore the skb->cb[] parts. There can be cases where the
actual attached program does not access the skb->cb[], but the program
tail calls into another program which does access this area. In such
a case, the zero or save/restore is currently not performed.
Since the programs we tail call into are unknown at verification time
and can dynamically change, we need to assume that whenever the attached
program performs a tail call, that later programs could access the
skb->cb[], and therefore we need to always set cb_access to 1.
Fixes: ff936a04e5 ("bpf: fix cb access in socket filter programs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After doing map_perf_test with a much bigger
BPF_F_NO_COMMON_LRU map, the perf report shows a
lot of time spent in rotating the inactive list (i.e.
__bpf_lru_list_rotate_inactive):
> map_perf_test 32 8 10000 1000000 | awk '{sum += $3}END{print sum}'
19644783 (19M/s)
> map_perf_test 32 8 10000000 10000000 | awk '{sum += $3}END{print sum}'
6283930 (6.28M/s)
By inactive, it usually means the element is not in cache. Hence,
there is a need to tune the PERCPU_NR_SCANS value.
This patch finds a better number of elements to
scan during each list rotation. The PERCPU_NR_SCANS (which
is defined the same as PERCPU_FREE_TARGET) decreases
from 16 elements to 4 elements. This change only
affects the BPF_F_NO_COMMON_LRU map.
The test_lru_dist does not show meaningful difference
between 16 and 4. Our production L4 load balancer which uses
the LRU map for conntrack-ing also shows little change in cache
hit rate. Since both benchmark and production data show no
cache-hit difference, PERCPU_NR_SCANS is lowered from 16 to 4.
We can consider making it configurable if we find a usecase
later that shows another value works better and/or use
a different rotation strategy.
After this change:
> map_perf_test 32 8 10000000 10000000 | awk '{sum += $3}END{print sum}'
9240324 (9.2M/s)
i.e. 6.28M/s -> 9.2M/s
The test_lru_dist has not shown meaningful difference:
> test_lru_dist zipf.100k.a1_01.out 4000 1:
nr_misses: 31575 (Before) vs 31566 (After)
> test_lru_dist zipf.100k.a0_01.out 40000 1
nr_misses: 67036 (Before) vs 67031 (After)
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were simply overlapping changes. In the net/ipv4/route.c
case the code had simply moved around a little bit and the same fix
was made in both 'net' and 'net-next'.
In the net/sched/sch_generic.c case a fix in 'net' happened at
the same time that a new argument was added to qdisc_hash_add().
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF helper functions access socket fields through skb->sk. This is not
set in ingress cgroup and socket filters. The association is only made
in skb_set_owner_r once the filter has accepted the packet. Sk is
available as socket lookup has taken place.
Temporarily set skb->sk to sk in these cases.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to have struct bpf_map_type_list since
it just contains a list_head, the type, and the ops
pointer. Since the types are densely packed and not
actually dynamically registered, it's much easier and
smaller to have an array of type->ops pointer. Also
initialize this array statically to remove code needed
to initialize it.
In order to save duplicating the list, move it to the
types header file added by the previous patch and
include it in the same fashion.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to have struct bpf_prog_type_list since
it just contains a list_head, the type, and the ops
pointer. Since the types are densely packed and not
actually dynamically registered, it's much easier and
smaller to have an array of type->ops pointer. Also
initialize this array statically to remove code needed
to initialize it.
In order to save duplicating the list, move it to a new
header file and include it in the places needing it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It took me quite some time to figure out how this was linked,
so in order to save the next person the effort of finding it
add a comment in __bpf_prog_run() that indicates what exactly
determines that a program can access the ctx == skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
development and testing of networking bpf programs is quite cumbersome.
Despite availability of user space bpf interpreters the kernel is
the ultimate authority and execution environment.
Current test frameworks for TC include creation of netns, veth,
qdiscs and use of various packet generators just to test functionality
of a bpf program. XDP testing is even more complicated, since
qemu needs to be started with gro/gso disabled and precise queue
configuration, transferring of xdp program from host into guest,
attaching to virtio/eth0 and generating traffic from the host
while capturing the results from the guest.
Moreover analyzing performance bottlenecks in XDP program is
impossible in virtio environment, since cost of running the program
is tiny comparing to the overhead of virtio packet processing,
so performance testing can only be done on physical nic
with another server generating traffic.
Furthermore ongoing changes to user space control plane of production
applications cannot be run on the test servers leaving bpf programs
stubbed out for testing.
Last but not least, the upstream llvm changes are validated by the bpf
backend testsuite which has no ability to test the code generated.
To improve this situation introduce BPF_PROG_TEST_RUN command
to test and performance benchmark bpf programs.
Joint work with Daniel Borkmann.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the verifier doesn't reject unaligned access for map_value_adj
register types. Commit 484611357c ("bpf: allow access into map value
arrays") added logic to check_ptr_alignment() extending it from PTR_TO_PACKET
to also PTR_TO_MAP_VALUE_ADJ, but for PTR_TO_MAP_VALUE_ADJ no enforcement
is in place, because reg->id for PTR_TO_MAP_VALUE_ADJ reg types is never
non-zero, meaning, we can cause BPF_H/_W/_DW-based unaligned access for
architectures not supporting efficient unaligned access, and thus worst
case could raise exceptions on some archs that are unable to correct the
unaligned access or perform a different memory access to the actual
requested one and such.
i) Unaligned load with !CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
on r0 (map_value_adj):
0: (bf) r2 = r10
1: (07) r2 += -8
2: (7a) *(u64 *)(r2 +0) = 0
3: (18) r1 = 0x42533a00
5: (85) call bpf_map_lookup_elem#1
6: (15) if r0 == 0x0 goto pc+11
R0=map_value(ks=8,vs=48,id=0),min_value=0,max_value=0 R10=fp
7: (61) r1 = *(u32 *)(r0 +0)
8: (35) if r1 >= 0xb goto pc+9
R0=map_value(ks=8,vs=48,id=0),min_value=0,max_value=0 R1=inv,min_value=0,max_value=10 R10=fp
9: (07) r0 += 3
10: (79) r7 = *(u64 *)(r0 +0)
R0=map_value_adj(ks=8,vs=48,id=0),min_value=3,max_value=3 R1=inv,min_value=0,max_value=10 R10=fp
11: (79) r7 = *(u64 *)(r0 +2)
R0=map_value_adj(ks=8,vs=48,id=0),min_value=3,max_value=3 R1=inv,min_value=0,max_value=10 R7=inv R10=fp
[...]
ii) Unaligned store with !CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
on r0 (map_value_adj):
0: (bf) r2 = r10
1: (07) r2 += -8
2: (7a) *(u64 *)(r2 +0) = 0
3: (18) r1 = 0x4df16a00
5: (85) call bpf_map_lookup_elem#1
6: (15) if r0 == 0x0 goto pc+19
R0=map_value(ks=8,vs=48,id=0),min_value=0,max_value=0 R10=fp
7: (07) r0 += 3
8: (7a) *(u64 *)(r0 +0) = 42
R0=map_value_adj(ks=8,vs=48,id=0),min_value=3,max_value=3 R10=fp
9: (7a) *(u64 *)(r0 +2) = 43
R0=map_value_adj(ks=8,vs=48,id=0),min_value=3,max_value=3 R10=fp
10: (7a) *(u64 *)(r0 -2) = 44
R0=map_value_adj(ks=8,vs=48,id=0),min_value=3,max_value=3 R10=fp
[...]
For the PTR_TO_PACKET type, reg->id is initially zero when skb->data
was fetched, it later receives a reg->id from env->id_gen generator
once another register with UNKNOWN_VALUE type was added to it via
check_packet_ptr_add(). The purpose of this reg->id is twofold: i) it
is used in find_good_pkt_pointers() for setting the allowed access
range for regs with PTR_TO_PACKET of same id once verifier matched
on data/data_end tests, and ii) for check_ptr_alignment() to determine
that when not having efficient unaligned access and register with
UNKNOWN_VALUE was added to PTR_TO_PACKET, that we're only allowed
to access the content bytewise due to unknown unalignment. reg->id
was never intended for PTR_TO_MAP_VALUE{,_ADJ} types and thus is
always zero, the only marking is in PTR_TO_MAP_VALUE_OR_NULL that
was added after 484611357c via 57a09bf0a4 ("bpf: Detect identical
PTR_TO_MAP_VALUE_OR_NULL registers"). Above tests will fail for
non-root environment due to prohibited pointer arithmetic.
The fix splits register-type specific checks into their own helper
instead of keeping them combined, so we don't run into a similar
issue in future once we extend check_ptr_alignment() further and
forget to add reg->type checks for some of the checks.
Fixes: 484611357c ("bpf: allow access into map value arrays")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking into map_value_adj, I noticed that alu operations
directly on the map_value() resp. map_value_adj() register (any
alu operation on a map_value() register will turn it into a
map_value_adj() typed register) are not sufficiently protected
against some of the operations. Two non-exhaustive examples are
provided that the verifier needs to reject:
i) BPF_AND on r0 (map_value_adj):
0: (bf) r2 = r10
1: (07) r2 += -8
2: (7a) *(u64 *)(r2 +0) = 0
3: (18) r1 = 0xbf842a00
5: (85) call bpf_map_lookup_elem#1
6: (15) if r0 == 0x0 goto pc+2
R0=map_value(ks=8,vs=48,id=0),min_value=0,max_value=0 R10=fp
7: (57) r0 &= 8
8: (7a) *(u64 *)(r0 +0) = 22
R0=map_value_adj(ks=8,vs=48,id=0),min_value=0,max_value=8 R10=fp
9: (95) exit
from 6 to 9: R0=inv,min_value=0,max_value=0 R10=fp
9: (95) exit
processed 10 insns
ii) BPF_ADD in 32 bit mode on r0 (map_value_adj):
0: (bf) r2 = r10
1: (07) r2 += -8
2: (7a) *(u64 *)(r2 +0) = 0
3: (18) r1 = 0xc24eee00
5: (85) call bpf_map_lookup_elem#1
6: (15) if r0 == 0x0 goto pc+2
R0=map_value(ks=8,vs=48,id=0),min_value=0,max_value=0 R10=fp
7: (04) (u32) r0 += (u32) 0
8: (7a) *(u64 *)(r0 +0) = 22
R0=map_value_adj(ks=8,vs=48,id=0),min_value=0,max_value=0 R10=fp
9: (95) exit
from 6 to 9: R0=inv,min_value=0,max_value=0 R10=fp
9: (95) exit
processed 10 insns
Issue is, while min_value / max_value boundaries for the access
are adjusted appropriately, we change the pointer value in a way
that cannot be sufficiently tracked anymore from its origin.
Operations like BPF_{AND,OR,DIV,MUL,etc} on a destination register
that is PTR_TO_MAP_VALUE{,_ADJ} was probably unintended, in fact,
all the test cases coming with 484611357c ("bpf: allow access
into map value arrays") perform BPF_ADD only on the destination
register that is PTR_TO_MAP_VALUE_ADJ.
Only for UNKNOWN_VALUE register types such operations make sense,
f.e. with unknown memory content fetched initially from a constant
offset from the map value memory into a register. That register is
then later tested against lower / upper bounds, so that the verifier
can then do the tracking of min_value / max_value, and properly
check once that UNKNOWN_VALUE register is added to the destination
register with type PTR_TO_MAP_VALUE{,_ADJ}. This is also what the
original use-case is solving. Note, tracking on what is being
added is done through adjust_reg_min_max_vals() and later access
to the map value enforced with these boundaries and the given offset
from the insn through check_map_access_adj().
Tests will fail for non-root environment due to prohibited pointer
arithmetic, in particular in check_alu_op(), we bail out on the
is_pointer_value() check on the dst_reg (which is false in root
case as we allow for pointer arithmetic via env->allow_ptr_leaks).
Similarly to PTR_TO_PACKET, one way to fix it is to restrict the
allowed operations on PTR_TO_MAP_VALUE{,_ADJ} registers to 64 bit
mode BPF_ADD. The test_verifier suite runs fine after the patch
and it also rejects mentioned test cases.
Fixes: 484611357c ("bpf: allow access into map value arrays")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
llvm can optimize the 'if (ptr > data_end)' checks to be in the order
slightly different than the original C code which will confuse verifier.
Like:
if (ptr + 16 > data_end)
return TC_ACT_SHOT;
// may be followed by
if (ptr + 14 > data_end)
return TC_ACT_SHOT;
while llvm can see that 'ptr' is valid for all 16 bytes,
the verifier could not.
Fix verifier logic to account for such case and add a test.
Reported-by: Huapeng Zhou <hzhou@fb.com>
Fixes: 969bf05eb3 ("bpf: direct packet access")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds hash of maps support (hashmap->bpf_map).
BPF_MAP_TYPE_HASH_OF_MAPS is added.
A map-in-map contains a pointer to another map and lets call
this pointer 'inner_map_ptr'.
Notes on deleting inner_map_ptr from a hash map:
1. For BPF_F_NO_PREALLOC map-in-map, when deleting
an inner_map_ptr, the htab_elem itself will go through
a rcu grace period and the inner_map_ptr resides
in the htab_elem.
2. For pre-allocated htab_elem (!BPF_F_NO_PREALLOC),
when deleting an inner_map_ptr, the htab_elem may
get reused immediately. This situation is similar
to the existing prealloc-ated use cases.
However, the bpf_map_fd_put_ptr() calls bpf_map_put() which calls
inner_map->ops->map_free(inner_map) which will go
through a rcu grace period (i.e. all bpf_map's map_free
currently goes through a rcu grace period). Hence,
the inner_map_ptr is still safe for the rcu reader side.
This patch also includes BPF_MAP_TYPE_HASH_OF_MAPS to the
check_map_prealloc() in the verifier. preallocation is a
must for BPF_PROG_TYPE_PERF_EVENT. Hence, even we don't expect
heavy updates to map-in-map, enforcing BPF_F_NO_PREALLOC for map-in-map
is impossible without disallowing BPF_PROG_TYPE_PERF_EVENT from using
map-in-map first.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a few helper funcs to enable map-in-map
support (i.e. outer_map->inner_map). The first outer_map type
BPF_MAP_TYPE_ARRAY_OF_MAPS is also added in this patch.
The next patch will introduce a hash of maps type.
Any bpf map type can be acted as an inner_map. The exception
is BPF_MAP_TYPE_PROG_ARRAY because the extra level of
indirection makes it harder to verify the owner_prog_type
and owner_jited.
Multi-level map-in-map is not supported (i.e. map->map is ok
but not map->map->map).
When adding an inner_map to an outer_map, it currently checks the
map_type, key_size, value_size, map_flags, max_entries and ops.
The verifier also uses those map's properties to do static analysis.
map_flags is needed because we need to ensure BPF_PROG_TYPE_PERF_EVENT
is using a preallocated hashtab for the inner_hash also. ops and
max_entries are needed to generate inlined map-lookup instructions.
For simplicity reason, a simple '==' test is used for both map_flags
and max_entries. The equality of ops is implied by the equality of
map_type.
During outer_map creation time, an inner_map_fd is needed to create an
outer_map. However, the inner_map_fd's life time does not depend on the
outer_map. The inner_map_fd is merely used to initialize
the inner_map_meta of the outer_map.
Also, for the outer_map:
* It allows element update and delete from syscall
* It allows element lookup from bpf_prog
The above is similar to the current fd_array pattern.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix in verifier:
For the same bpf_map_lookup_elem() instruction (i.e. "call 1"),
a broken case is "a different type of map could be used for the
same lookup instruction". For example, an array in one case and a
hashmap in another. We have to resort to the old dynamic call behavior
in this case. The fix is to check for collision on insn_aux->map_ptr.
If there is collision, don't inline the map lookup.
Please see the "do_reg_lookup()" in test_map_in_map_kern.c in the later
patch for how-to trigger the above case.
Simplifications on array_map_gen_lookup():
1. Calculate elem_size from map->value_size. It removes the
need for 'struct bpf_array' which makes the later map-in-map
implementation easier.
2. Remove the 'elem_size == 1' test
Fixes: 81ed18ab30 ("bpf: add helper inlining infra and optimize map_array lookup")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In both kmalloc and prealloc mode the bpf_map_update_elem() is using
per-cpu extra_elems to do atomic update when the map is full.
There are two issues with it. The logic can be misused, since it allows
max_entries+num_cpus elements to be present in the map. And alloc_extra_elems()
at map creation time can fail percpu alloc for large map values with a warn:
WARNING: CPU: 3 PID: 2752 at ../mm/percpu.c:892 pcpu_alloc+0x119/0xa60
illegal size (32824) or align (8) for percpu allocation
The fixes for both of these issues are different for kmalloc and prealloc modes.
For prealloc mode allocate extra num_possible_cpus elements and store
their pointers into extra_elems array instead of actual elements.
Hence we can use these hidden(spare) elements not only when the map is full
but during bpf_map_update_elem() that replaces existing element too.
That also improves performance, since pcpu_freelist_pop/push is avoided.
Unfortunately this approach cannot be used for kmalloc mode which needs
to kfree elements after rcu grace period. Therefore switch it back to normal
kmalloc even when full and old element exists like it was prior to
commit 6c90598174 ("bpf: pre-allocate hash map elements").
Add tests to check for over max_entries and large map values.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Fixes: 6c90598174 ("bpf: pre-allocate hash map elements")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize:
bpf_call
bpf_map_lookup_elem
map->ops->map_lookup_elem
htab_map_lookup_elem
__htab_map_lookup_elem
into:
bpf_call
__htab_map_lookup_elem
to improve performance of JITed programs.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize bpf_call -> bpf_map_lookup_elem() -> array_map_lookup_elem()
into a sequence of bpf instructions.
When JIT is on the sequence of bpf instructions is the sequence
of native cpu instructions with significantly faster performance
than indirect call and two function's prologue/epilogue.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
convert_ctx_accesses() replaces single bpf instruction with a set of
instructions. Adjust corresponding insn_aux_data while patching.
It's needed to make sure subsequent 'for(all insn)' loops
have matching insn and insn_aux_data.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
reduce indent and make it iterate over instructions similar to
convert_ctx_accesses(). Also convert hard BUG_ON into soft verifier error.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
no functional change.
move fixup_bpf_calls() to verifier.c
it's being refactored in the next patch
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
when all map elements are pre-allocated one cpu can delete and reuse htab_elem
while another cpu is still walking the hlist. In such case the lookup may
miss the element. Convert hlist to hlist_nulls to avoid such scenario.
When bucket lock is taken there is no need to take such precautions,
so only convert map_lookup and map_get_next to nulls.
The race window is extremely small and only reproducible with explicit
udelay() inside lookup_nulls_elem_raw()
Similar to hlist add hlist_nulls_for_each_entry_safe() and
hlist_nulls_entry_safe() helpers.
Fixes: 6c90598174 ("bpf: pre-allocate hash map elements")
Reported-by: Jonathan Perry <jonperry@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
when htab_elem is removed from the bucket list the htab_elem.hash_node.next
field should not be overridden too early otherwise we have a tiny race window
between lookup and delete.
The bug was discovered by manual code analysis and reproducible
only with explicit udelay() in lookup_elem_raw().
Fixes: 6c90598174 ("bpf: pre-allocate hash map elements")
Reported-by: Jonathan Perry <jonperry@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix double-free in batman-adv, from Sven Eckelmann.
2) Fix packet stats for fast-RX path, from Joannes Berg.
3) Netfilter's ip_route_me_harder() doesn't handle request sockets
properly, fix from Florian Westphal.
4) Fix sendmsg deadlock in rxrpc, from David Howells.
5) Add missing RCU locking to transport hashtable scan, from Xin Long.
6) Fix potential packet loss in mlxsw driver, from Ido Schimmel.
7) Fix race in NAPI handling between poll handlers and busy polling,
from Eric Dumazet.
8) TX path in vxlan and geneve need proper RCU locking, from Jakub
Kicinski.
9) SYN processing in DCCP and TCP need to disable BH, from Eric
Dumazet.
10) Properly handle net_enable_timestamp() being invoked from IRQ
context, also from Eric Dumazet.
11) Fix crash on device-tree systems in xgene driver, from Alban Bedel.
12) Do not call sk_free() on a locked socket, from Arnaldo Carvalho de
Melo.
13) Fix use-after-free in netvsc driver, from Dexuan Cui.
14) Fix max MTU setting in bonding driver, from WANG Cong.
15) xen-netback hash table can be allocated from softirq context, so use
GFP_ATOMIC. From Anoob Soman.
16) Fix MAC address change bug in bgmac driver, from Hari Vyas.
17) strparser needs to destroy strp_wq on module exit, from WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
strparser: destroy workqueue on module exit
sfc: fix IPID endianness in TSOv2
sfc: avoid max() in array size
rds: remove unnecessary returned value check
rxrpc: Fix potential NULL-pointer exception
nfp: correct DMA direction in XDP DMA sync
nfp: don't tell FW about the reserved buffer space
net: ethernet: bgmac: mac address change bug
net: ethernet: bgmac: init sequence bug
xen-netback: don't vfree() queues under spinlock
xen-netback: keep a local pointer for vif in backend_disconnect()
netfilter: nf_tables: don't call nfnetlink_set_err() if nfnetlink_send() fails
netfilter: nft_set_rbtree: incorrect assumption on lower interval lookups
netfilter: nf_conntrack_sip: fix wrong memory initialisation
can: flexcan: fix typo in comment
can: usb_8dev: Fix memory leak of priv->cmd_msg_buffer
can: gs_usb: fix coding style
can: gs_usb: Don't use stack memory for USB transfers
ixgbe: Limit use of 2K buffers on architectures with 256B or larger cache lines
ixgbe: update the rss key on h/w, when ethtool ask for it
...
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 07016151a4 ("bpf, verifier: further improve search
pruning") increased the limit of processed instructions from
32k to 64k, but the comment still mentioned the 32k limit.
This commit updates the comment to reflect the change.
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Gary Lin <glin@suse.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake in verbose log message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Long standing issue with JITed programs is that stack traces from
function tracing check whether a given address is kernel code
through {__,}kernel_text_address(), which checks for code in core
kernel, modules and dynamically allocated ftrace trampolines. But
what is still missing is BPF JITed programs (interpreted programs
are not an issue as __bpf_prog_run() will be attributed to them),
thus when a stack trace is triggered, the code walking the stack
won't see any of the JITed ones. The same for address correlation
done from user space via reading /proc/kallsyms. This is read by
tools like perf, but the latter is also useful for permanent live
tracing with eBPF itself in combination with stack maps when other
eBPF types are part of the callchain. See offwaketime example on
dumping stack from a map.
This work tries to tackle that issue by making the addresses and
symbols known to the kernel. The lookup from *kernel_text_address()
is implemented through a latched RB tree that can be read under
RCU in fast-path that is also shared for symbol/size/offset lookup
for a specific given address in kallsyms. The slow-path iteration
through all symbols in the seq file done via RCU list, which holds
a tiny fraction of all exported ksyms, usually below 0.1 percent.
Function symbols are exported as bpf_prog_<tag>, in order to aide
debugging and attribution. This facility is currently enabled for
root-only when bpf_jit_kallsyms is set to 1, and disabled if hardening
is active in any mode. The rationale behind this is that still a lot
of systems ship with world read permissions on kallsyms thus addresses
should not get suddenly exposed for them. If that situation gets
much better in future, we always have the option to change the
default on this. Likewise, unprivileged programs are not allowed
to add entries there either, but that is less of a concern as most
such programs types relevant in this context are for root-only anyway.
If enabled, call graphs and stack traces will then show a correct
attribution; one example is illustrated below, where the trace is
now visible in tooling such as perf script --kallsyms=/proc/kallsyms
and friends.
Before:
7fff8166889d bpf_clone_redirect+0x80007f0020ed (/lib/modules/4.9.0-rc8+/build/vmlinux)
f5d80 __sendmsg_nocancel+0xffff006451f1a007 (/usr/lib64/libc-2.18.so)
After:
7fff816688b7 bpf_clone_redirect+0x80007f002107 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fffa0575728 bpf_prog_33c45a467c9e061a+0x8000600020fb (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fffa07ef1fc cls_bpf_classify+0x8000600020dc (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff81678b68 tc_classify+0x80007f002078 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164d40b __netif_receive_skb_core+0x80007f0025fb (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164d718 __netif_receive_skb+0x80007f002018 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164e565 process_backlog+0x80007f002095 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8164dc71 net_rx_action+0x80007f002231 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff81767461 __softirqentry_text_start+0x80007f0020d1 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff817658ac do_softirq_own_stack+0x80007f00201c (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff810a2c20 do_softirq+0x80007f002050 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff810a2cb5 __local_bh_enable_ip+0x80007f002085 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168d452 ip_finish_output2+0x80007f002152 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168ea3d ip_finish_output+0x80007f00217d (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff8168f2af ip_output+0x80007f00203f (/lib/modules/4.9.0-rc8+/build/vmlinux)
[...]
7fff81005854 do_syscall_64+0x80007f002054 (/lib/modules/4.9.0-rc8+/build/vmlinux)
7fff817649eb return_from_SYSCALL_64+0x80007f002000 (/lib/modules/4.9.0-rc8+/build/vmlinux)
f5d80 __sendmsg_nocancel+0xffff01c484812007 (/usr/lib64/libc-2.18.so)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the dummy bpf_jit_compile() stubs for eBPF JITs and make
that a single __weak function in the core that can be overridden
similarly to the eBPF one. Also remove stale pr_err() mentions
of bpf_jit_compile.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All map types and prog types are registered to the BPF core through
bpf_register_map_type() and bpf_register_prog_type() during init and
remain unchanged thereafter. As by design we don't (and never will)
have any pluggable code that can register to that at any later point
in time, lets mark all the existing bpf_{map,prog}_type_list objects
in the tree as __ro_after_init, so they can be moved to read-only
section from then onwards.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following warnings:
kernel/bpf/verifier.c: In function ‘may_access_direct_pkt_data’:
kernel/bpf/verifier.c:702:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (t == BPF_WRITE)
^
kernel/bpf/verifier.c:704:2: note: here
case BPF_PROG_TYPE_SCHED_CLS:
^~~~
kernel/bpf/verifier.c: In function ‘reg_set_min_max_inv’:
kernel/bpf/verifier.c:2057:23: warning: this statement may fall through [-Wimplicit-fallthrough=]
true_reg->min_value = 0;
~~~~~~~~~~~~~~~~~~~~^~~
kernel/bpf/verifier.c:2058:2: note: here
case BPF_JSGT:
^~~~
kernel/bpf/verifier.c:2068:23: warning: this statement may fall through [-Wimplicit-fallthrough=]
true_reg->min_value = 0;
~~~~~~~~~~~~~~~~~~~~^~~
kernel/bpf/verifier.c:2069:2: note: here
case BPF_JSGE:
^~~~
kernel/bpf/verifier.c: In function ‘reg_set_min_max’:
kernel/bpf/verifier.c:2009:24: warning: this statement may fall through [-Wimplicit-fallthrough=]
false_reg->min_value = 0;
~~~~~~~~~~~~~~~~~~~~~^~~
kernel/bpf/verifier.c:2010:2: note: here
case BPF_JSGT:
^~~~
kernel/bpf/verifier.c:2019:24: warning: this statement may fall through [-Wimplicit-fallthrough=]
false_reg->min_value = 0;
~~~~~~~~~~~~~~~~~~~~~^~~
kernel/bpf/verifier.c:2020:2: note: here
case BPF_JSGE:
^~~~
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If BPF_F_ALLOW_OVERRIDE flag is used in BPF_PROG_ATTACH command
to the given cgroup the descendent cgroup will be able to override
effective bpf program that was inherited from this cgroup.
By default it's not passed, therefore override is disallowed.
Examples:
1.
prog X attached to /A with default
prog Y fails to attach to /A/B and /A/B/C
Everything under /A runs prog X
2.
prog X attached to /A with allow_override.
prog Y fails to attach to /A/B with default (non-override)
prog M attached to /A/B with allow_override.
Everything under /A/B runs prog M only.
3.
prog X attached to /A with allow_override.
prog Y fails to attach to /A with default.
The user has to detach first to switch the mode.
In the future this behavior may be extended with a chain of
non-overridable programs.
Also fix the bug where detach from cgroup where nothing is attached
was not throwing error. Return ENOENT in such case.
Add several testcases and adjust libbpf.
Fixes: 3007098494 ("cgroup: add support for eBPF programs")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cap the maximum (total) value size and bail out if larger than KMALLOC_MAX_SIZE
as otherwise it doesn't make any sense to proceed further, since we're
guaranteed to fail to allocate elements anyway in lpm_trie_node_alloc();
likleyhood of failure is still high for large values, though, similarly
as with htab case in non-prealloc.
Next, make sure that cost vars are really u64 instead of size_t, so that we
don't overflow on 32 bit and charge only tiny map.pages against memlock while
allowing huge max_entries; cap also the max cost like we do with other map
types.
Fixes: b95a5c4db0 ("bpf: add a longest prefix match trie map implementation")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes the case when adding a zero value to the packet
pointer. The zero value could come from src_reg equals type
BPF_K or CONST_IMM. The patch fixes both, otherwise the verifer
reports the following error:
[...]
R0=imm0,min_value=0,max_value=0
R1=pkt(id=0,off=0,r=4)
R2=pkt_end R3=fp-12
R4=imm4,min_value=4,max_value=4
R5=pkt(id=0,off=4,r=4)
269: (bf) r2 = r0 // r2 becomes imm0
270: (77) r2 >>= 3
271: (bf) r4 = r1 // r4 becomes pkt ptr
272: (0f) r4 += r2 // r4 += 0
addition of negative constant to packet pointer is not allowed
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: Mihai Budiu <mbudiu@vmware.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a number of tracepoints to paths that are either
considered slow-path or exception-like states, where monitoring or
inspecting them would be desirable.
For bpf(2) syscall, tracepoints have been placed for main commands
when they succeed. In XDP case, tracepoint is for exceptions, that
is, f.e. on abnormal BPF program exit such as unknown or XDP_ABORTED
return code, or when error occurs during XDP_TX action and the packet
could not be forwarded.
Both have been split into separate event headers, and can be further
extended. Worst case, if they unexpectedly should get into our way in
future, they can also removed [1]. Of course, these tracepoints (like
any other) can be analyzed by eBPF itself, etc. Example output:
# ./perf record -a -e bpf:* sleep 10
# ./perf script
sock_example 6197 [005] 283.980322: bpf:bpf_map_create: map type=ARRAY ufd=4 key=4 val=8 max=256 flags=0
sock_example 6197 [005] 283.980721: bpf:bpf_prog_load: prog=a5ea8fa30ea6849c type=SOCKET_FILTER ufd=5
sock_example 6197 [005] 283.988423: bpf:bpf_prog_get_type: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
sock_example 6197 [005] 283.988443: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[06 00 00 00] val=[00 00 00 00 00 00 00 00]
[...]
sock_example 6197 [005] 288.990868: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[01 00 00 00] val=[14 00 00 00 00 00 00 00]
swapper 0 [005] 289.338243: bpf:bpf_prog_put_rcu: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
[1] https://lwn.net/Articles/705270/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
William reported couple of issues in relation to direct packet
access. Typical scheme is to check for data + [off] <= data_end,
where [off] can be either immediate or coming from a tracked
register that contains an immediate, depending on the branch, we
can then access the data. However, in case of calculating [off]
for either the mentioned test itself or for access after the test
in a more "complex" way, then the verifier will stop tracking the
CONST_IMM marked register and will mark it as UNKNOWN_VALUE one.
Adding that UNKNOWN_VALUE typed register to a pkt() marked
register, the verifier then bails out in check_packet_ptr_add()
as it finds the registers imm value below 48. In the first below
example, that is due to evaluate_reg_imm_alu() not handling right
shifts and thus marking the register as UNKNOWN_VALUE via helper
__mark_reg_unknown_value() that resets imm to 0.
In the second case the same happens at the time when r4 is set
to r4 &= r5, where it transitions to UNKNOWN_VALUE from
evaluate_reg_imm_alu(). Later on r4 we shift right by 3 inside
evaluate_reg_alu(), where the register's imm turns into 3. That
is, for registers with type UNKNOWN_VALUE, imm of 0 means that
we don't know what value the register has, and for imm > 0 it
means that the value has [imm] upper zero bits. F.e. when shifting
an UNKNOWN_VALUE register by 3 to the right, no matter what value
it had, we know that the 3 upper most bits must be zero now.
This is to make sure that ALU operations with unknown registers
don't overflow. Meaning, once we know that we have more than 48
upper zero bits, or, in other words cannot go beyond 0xffff offset
with ALU ops, such an addition will track the target register
as a new pkt() register with a new id, but 0 offset and 0 range,
so for that a new data/data_end test will be required. Is the source
register a CONST_IMM one that is to be added to the pkt() register,
or the source instruction is an add instruction with immediate
value, then it will get added if it stays within max 0xffff bounds.
>From there, pkt() type, can be accessed should reg->off + imm be
within the access range of pkt().
[...]
from 28 to 30: R0=imm1,min_value=1,max_value=1
R1=pkt(id=0,off=0,r=22) R2=pkt_end
R3=imm144,min_value=144,max_value=144
R4=imm0,min_value=0,max_value=0
R5=inv48,min_value=2054,max_value=2054 R10=fp
30: (bf) r5 = r3
31: (07) r5 += 23
32: (77) r5 >>= 3
33: (bf) r6 = r1
34: (0f) r6 += r5
cannot add integer value with 0 upper zero bits to ptr_to_packet
[...]
from 52 to 80: R0=imm1,min_value=1,max_value=1
R1=pkt(id=0,off=0,r=34) R2=pkt_end R3=inv
R4=imm272 R5=inv56,min_value=17,max_value=17
R6=pkt(id=0,off=26,r=34) R10=fp
80: (07) r4 += 71
81: (18) r5 = 0xfffffff8
83: (5f) r4 &= r5
84: (77) r4 >>= 3
85: (0f) r1 += r4
cannot add integer value with 3 upper zero bits to ptr_to_packet
Thus to get above use-cases working, evaluate_reg_imm_alu() has
been extended for further ALU ops. This is fine, because we only
operate strictly within realm of CONST_IMM types, so here we don't
care about overflows as they will happen in the simulated but also
real execution and interaction with pkt() in check_packet_ptr_add()
will check actual imm value once added to pkt(), but it's irrelevant
before.
With regards to 06c1c04972 ("bpf: allow helpers access to variable
memory") that works on UNKNOWN_VALUE registers, the verifier becomes
now a bit smarter as it can better resolve ALU ops, so we need to
adapt two test cases there, as min/max bound tracking only becomes
necessary when registers were spilled to stack. So while mask was
set before to track upper bound for UNKNOWN_VALUE case, it's now
resolved directly as CONST_IMM, and such contructs are only necessary
when f.e. registers are spilled.
For commit 6b17387307 ("bpf: recognize 64bit immediate loads as
consts") that initially enabled dw load tracking only for nfp jit/
analyzer, I did couple of tests on large, complex programs and we
don't increase complexity badly (my tests were in ~3% range on avg).
I've added a couple of tests similar to affected code above, and
it works fine with verifier now.
Reported-by: William Tu <u9012063@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Gianluca Borello <g.borello@gmail.com>
Cc: William Tu <u9012063@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to initialize im_node to NULL, otherwise in case of error path
it gets passed to kfree() as uninitialized pointer.
Fixes: b95a5c4db0 ("bpf: add a longest prefix match trie map implementation")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trie implements a longest prefix match algorithm that can be used
to match IP addresses to a stored set of ranges.
Internally, data is stored in an unbalanced trie of nodes that has a
maximum height of n, where n is the prefixlen the trie was created
with.
Tries may be created with prefix lengths that are multiples of 8, in
the range from 8 to 2048. The key used for lookup and update operations
is a struct bpf_lpm_trie_key, and the value is a uint64_t.
The code carries more information about the internal implementation.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two helpers, bpf_map_area_alloc() and bpf_map_area_free(),
that are to be used for map allocations. Using kmalloc() for very large
allocations can cause excessive work within the page allocator, so i) fall
back earlier to vmalloc() when the attempt is considered costly anyway,
and even more importantly ii) don't trigger OOM killer with any of the
allocators.
Since this is based on a user space request, for example, when creating
maps with element pre-allocation, we really want such requests to fail
instead of killing other user space processes.
Also, don't spam the kernel log with warnings should any of the allocations
fail under pressure. Given that, we can make backend selection in
bpf_map_area_alloc() generic, and convert all maps over to use this API
for spots with potentially large allocation requests.
Note, replacing the one kmalloc_array() is fine as overflow checks happen
earlier in htab_map_alloc(), since it must also protect the multiplication
for vmalloc() should kmalloc_array() fail.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7bd509e311 ("bpf: add prog_digest and expose it via
fdinfo/netlink") was recently discussed, partially due to
admittedly suboptimal name of "prog_digest" in combination
with sha1 hash usage, thus inevitably and rightfully concerns
about its security in terms of collision resistance were
raised with regards to use-cases.
The intended use cases are for debugging resp. introspection
only for providing a stable "tag" over the instruction sequence
that both kernel and user space can calculate independently.
It's not usable at all for making a security relevant decision.
So collisions where two different instruction sequences generate
the same tag can happen, but ideally at a rather low rate. The
"tag" will be dumped in hex and is short enough to introspect
in tracepoints or kallsyms output along with other data such
as stack trace, etc. Thus, this patch performs a rename into
prog_tag and truncates the tag to a short output (64 bits) to
make it obvious it's not collision-free.
Should in future a hash or facility be needed with a security
relevant focus, then we can think about requirements, constraints,
etc that would fit to that situation. For now, rework the exposed
parts for the current use cases as long as nothing has been
released yet. Tested on x86_64 and s390x.
Fixes: 7bd509e311 ("bpf: add prog_digest and expose it via fdinfo/netlink")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When structs are used to store temporary state in cb[] buffer that is
used with programs and among tail calls, then the generated code will
not always access the buffer in bpf_w chunks. We can ease programming
of it and let this act more natural by allowing for aligned b/h/w/dw
sized access for cb[] ctx member. Various test cases are attached as
well for the selftest suite. Potentially, this can also be reused for
other program types to pass data around.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when calling convert_ctx_access() callback for the various
program types, we pass in insn->dst_reg, insn->src_reg, insn->off from
the original instruction. This information is needed to rewrite the
instruction that is based on the user ctx structure into a kernel
representation for the ctx. As we'd like to allow access size beyond
just BPF_W, we'd need also insn->code for that in order to decode the
original access size. Given that, lets just pass insn directly to the
convert_ctx_access() callback and work on that to not clutter the
callback with even more arguments we need to pass when everything is
already contained in insn. So lets go through that once, no functional
change.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 01b3f52157 ("bpf: fix allocation warnings in bpf maps and
integer overflow") has added checks for the maximum allocateable size.
It (ab)used KMALLOC_SHIFT_MAX for that purpose.
While this is not incorrect it is not very clean because we already have
KMALLOC_MAX_SIZE for this very reason so let's change both checks to use
KMALLOC_MAX_SIZE instead.
The original motivation for using KMALLOC_SHIFT_MAX was to work around
an incorrect KMALLOC_MAX_SIZE which could lead to allocation warnings
but it is no longer needed since "slab: make sure that KMALLOC_MAX_SIZE
will fit into MAX_ORDER".
Link: http://lkml.kernel.org/r/20161220130659.16461-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the functions __local_list_pop_free(), __local_list_pop_pending(),
bpf_common_lru_populate() and bpf_percpu_lru_populate() static as they
are not used outide of bpf_lru_list.c
This fixes the following GCC warnings when building with 'W=1':
kernel/bpf/bpf_lru_list.c:363:22: warning: no previous prototype for ‘__local_list_pop_free’ [-Wmissing-prototypes]
kernel/bpf/bpf_lru_list.c:376:22: warning: no previous prototype for ‘__local_list_pop_pending’ [-Wmissing-prototypes]
kernel/bpf/bpf_lru_list.c:560:6: warning: no previous prototype for ‘bpf_common_lru_populate’ [-Wmissing-prototypes]
kernel/bpf/bpf_lru_list.c:577:6: warning: no previous prototype for ‘bpf_percpu_lru_populate’ [-Wmissing-prototypes]
Cc: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unused but set variable 'first_node' in
__bpf_lru_list_shrink_inactive() to fix the following GCC warning when
building with 'W=1':
kernel/bpf/bpf_lru_list.c:216:41: warning: variable ‘first_node’ set but not used [-Wunused-but-set-variable]
Cc: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since ARG_PTR_TO_STACK is no longer just pointer to stack
rename it to ARG_PTR_TO_MEM and adjust comment.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, helpers that read and write from/to the stack can do so using
a pair of arguments of type ARG_PTR_TO_STACK and ARG_CONST_STACK_SIZE.
ARG_CONST_STACK_SIZE accepts a constant register of type CONST_IMM, so
that the verifier can safely check the memory access. However, requiring
the argument to be a constant can be limiting in some circumstances.
Since the current logic keeps track of the minimum and maximum value of
a register throughout the simulated execution, ARG_CONST_STACK_SIZE can
be changed to also accept an UNKNOWN_VALUE register in case its
boundaries have been set and the range doesn't cause invalid memory
accesses.
One common situation when this is useful:
int len;
char buf[BUFSIZE]; /* BUFSIZE is 128 */
if (some_condition)
len = 42;
else
len = 84;
some_helper(..., buf, len & (BUFSIZE - 1));
The compiler can often decide to assign the constant values 42 or 48
into a variable on the stack, instead of keeping it in a register. When
the variable is then read back from stack into the register in order to
be passed to the helper, the verifier will not be able to recognize the
register as constant (the verifier is not currently tracking all
constant writes into memory), and the program won't be valid.
However, by allowing the helper to accept an UNKNOWN_VALUE register,
this program will work because the bitwise AND operation will set the
range of possible values for the UNKNOWN_VALUE register to [0, BUFSIZE),
so the verifier can guarantee the helper call will be safe (assuming the
argument is of type ARG_CONST_STACK_SIZE_OR_ZERO, otherwise one more
check against 0 would be needed). Custom ranges can be set not only with
ALU operations, but also by explicitly comparing the UNKNOWN_VALUE
register with constants.
Another very common example happens when intercepting system call
arguments and accessing user-provided data of variable size using
bpf_probe_read(). One can load at runtime the user-provided length in an
UNKNOWN_VALUE register, and then read that exact amount of data up to a
compile-time determined limit in order to fit into the proper local
storage allocated on the stack, without having to guess a suboptimal
access size at compile time.
Also, in case the helpers accepting the UNKNOWN_VALUE register operate
in raw mode, disable the raw mode so that the program is required to
initialize all memory, since there is no guarantee the helper will fill
it completely, leaving possibilities for data leak (just relevant when
the memory used by the helper is the stack, not when using a pointer to
map element value or packet). In other words, ARG_PTR_TO_RAW_STACK will
be treated as ARG_PTR_TO_STACK.
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 484611357c ("bpf: allow access into map value arrays")
introduces the ability to do pointer math inside a map element value via
the PTR_TO_MAP_VALUE_ADJ register type.
The current support doesn't handle the case where a PTR_TO_MAP_VALUE_ADJ
is spilled into the stack, limiting several use cases, especially when
generating bpf code from a compiler.
Handle this case by explicitly enabling the register type
PTR_TO_MAP_VALUE_ADJ to be spilled. Also, make sure that min_value and
max_value are reset just for BPF_LDX operations that don't result in a
restore of a spilled register from stack.
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable helpers to directly access a map element value by passing a
register type PTR_TO_MAP_VALUE (or PTR_TO_MAP_VALUE_ADJ) to helper
arguments ARG_PTR_TO_STACK or ARG_PTR_TO_RAW_STACK.
This enables several use cases. For example, a typical tracing program
might want to capture pathnames passed to sys_open() with:
struct trace_data {
char pathname[PATHLEN];
};
SEC("kprobe/sys_open")
void bpf_sys_open(struct pt_regs *ctx)
{
struct trace_data data;
bpf_probe_read(data.pathname, sizeof(data.pathname), ctx->di);
/* consume data.pathname, for example via
* bpf_trace_printk() or bpf_perf_event_output()
*/
}
Such a program could easily hit the stack limit in case PATHLEN needs to
be large or more local variables need to exist, both of which are quite
common scenarios. Allowing direct helper access to map element values,
one could do:
struct bpf_map_def SEC("maps") scratch_map = {
.type = BPF_MAP_TYPE_PERCPU_ARRAY,
.key_size = sizeof(u32),
.value_size = sizeof(struct trace_data),
.max_entries = 1,
};
SEC("kprobe/sys_open")
int bpf_sys_open(struct pt_regs *ctx)
{
int id = 0;
struct trace_data *p = bpf_map_lookup_elem(&scratch_map, &id);
if (!p)
return;
bpf_probe_read(p->pathname, sizeof(p->pathname), ctx->di);
/* consume p->pathname, for example via
* bpf_trace_printk() or bpf_perf_event_output()
*/
}
And wouldn't risk exhausting the stack.
Code changes are loosely modeled after commit 6841de8b0d ("bpf: allow
helpers access the packet directly"). Unlike with PTR_TO_PACKET, these
changes just work with ARG_PTR_TO_STACK and ARG_PTR_TO_RAW_STACK (not
ARG_PTR_TO_MAP_KEY, ARG_PTR_TO_MAP_VALUE, ...): adding those would be
trivial, but since there is not currently a use case for that, it's
reasonable to limit the set of changes.
Also, add new tests to make sure accesses to map element values from
helpers never go out of boundary, even when adjusted.
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the logic to check memory accesses to a PTR_TO_MAP_VALUE_ADJ from
check_mem_access() to a separate helper check_map_access_adj(). This
enables to use those checks in other parts of the verifier as well,
where boundaries on PTR_TO_MAP_VALUE_ADJ might need to be checked, for
example when checking helper function arguments. The same thing is
already happening for other types such as PTR_TO_PACKET and its
check_packet_access() helper.
The code has been copied verbatim, with the only difference of removing
the "off += reg->max_value" statement and moving the sum into the call
statement to check_map_access(), as that was only needed due to the
earlier common check_map_access() call.
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin reported a verifier issue that hit the BUG_ON() for his
test case in the mark_reg_unknown_value() function:
[ 202.861380] kernel BUG at kernel/bpf/verifier.c:467!
[...]
[ 203.291109] Call Trace:
[ 203.296501] [<ffffffff811364d5>] mark_map_reg+0x45/0x50
[ 203.308225] [<ffffffff81136558>] mark_map_regs+0x78/0x90
[ 203.320140] [<ffffffff8113938d>] do_check+0x226d/0x2c90
[ 203.331865] [<ffffffff8113a6ab>] bpf_check+0x48b/0x780
[ 203.343403] [<ffffffff81134c8e>] bpf_prog_load+0x27e/0x440
[ 203.355705] [<ffffffff8118a38f>] ? handle_mm_fault+0x11af/0x1230
[ 203.369158] [<ffffffff812d8188>] ? security_capable+0x48/0x60
[ 203.382035] [<ffffffff811351a4>] SyS_bpf+0x124/0x960
[ 203.393185] [<ffffffff810515f6>] ? __do_page_fault+0x276/0x490
[ 203.406258] [<ffffffff816db320>] entry_SYSCALL_64_fastpath+0x13/0x94
This issue got uncovered after the fix in a08dd0da53 ("bpf: fix
regression on verifier pruning wrt map lookups"). The reason why it
wasn't noticed before was, because as mentioned in a08dd0da53,
mark_map_regs() was doing the id matching incorrectly based on the
uncached regs[regno].id. So, in the first loop, we walked all regs
and as soon as we found regno == i, then this reg's id was cleared
when calling mark_reg_unknown_value() thus that every subsequent
register was probed against id of 0 (which, in combination with the
PTR_TO_MAP_VALUE_OR_NULL type is an invalid condition that no other
register state can hold), and therefore wasn't type transitioned such
as in the spilled register case for the second loop.
Now since that got fixed, it turned out that 57a09bf0a4 ("bpf:
Detect identical PTR_TO_MAP_VALUE_OR_NULL registers") used
mark_reg_unknown_value() incorrectly for the spilled regs, and thus
hitting the BUG_ON() in some cases due to regno >= MAX_BPF_REG.
Although spilled regs have the same type as the non-spilled regs
for the verifier state, that is, struct bpf_reg_state, they are
semantically different from the non-spilled regs. In other words,
there can be up to 64 (MAX_BPF_STACK / BPF_REG_SIZE) spilled regs
in the stack, for example, register R<x> could have been spilled by
the program to stack location X, Y, Z, and in mark_map_regs() we
need to scan these stack slots of type STACK_SPILL for potential
registers that we have to transition from PTR_TO_MAP_VALUE_OR_NULL.
Therefore, depending on the location, the spilled_regs regno can
be a lot higher than just MAX_BPF_REG's value since we operate on
stack instead. The reset in mark_reg_unknown_value() itself is
just fine, only that the BUG_ON() was inappropriate for this. Fix
it by making a __mark_reg_unknown_value() version that can be
called from mark_map_reg() generically; we know for the non-spilled
case that the regno is always < MAX_BPF_REG anyway.
Fixes: 57a09bf0a4 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers")
Reported-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit aaac3ba95e ("bpf: charge user for creation of BPF maps and
programs") made a wrong assumption of charging against prog->pages.
Unlike map->pages, prog->pages are still subject to change when we
need to expand the program through bpf_prog_realloc().
This can for example happen during verification stage when we need to
expand and rewrite parts of the program. Should the required space
cross a page boundary, then prog->pages is not the same anymore as
its original value that we used to bpf_prog_charge_memlock() on. Thus,
we'll hit a wrap-around during bpf_prog_uncharge_memlock() when prog
is freed eventually. I noticed this that despite having unlimited
memlock, programs suddenly refused to load with EPERM error due to
insufficient memlock.
There are two ways to fix this issue. One would be to add a cached
variable to struct bpf_prog that takes a snapshot of prog->pages at the
time of charging. The other approach is to also account for resizes. I
chose to go with the latter for a couple of reasons: i) We want accounting
rather to be more accurate instead of further fooling limits, ii) adding
yet another page counter on struct bpf_prog would also be a waste just
for this purpose. We also do want to charge as early as possible to
avoid going into the verifier just to find out later on that we crossed
limits. The only place that needs to be fixed is bpf_prog_realloc(),
since only here we expand the program, so we try to account for the
needed delta and should we fail, call-sites check for outcome anyway.
On cBPF to eBPF migrations, we don't grab a reference to the user as
they are charged differently. With that in place, my test case worked
fine.
Fixes: aaac3ba95e ("bpf: charge user for creation of BPF maps and programs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert rightfully complained that 7bd509e311 ("bpf: add prog_digest
and expose it via fdinfo/netlink") added a too large allocation of
variable 'raw' from bss section, and should instead be done dynamically:
# ./scripts/bloat-o-meter kernel/bpf/core.o.1 kernel/bpf/core.o.2
add/remove: 3/0 grow/shrink: 0/0 up/down: 33291/0 (33291)
function old new delta
raw - 32832 +32832
[...]
Since this is only relevant during program creation path, which can be
considered slow-path anyway, lets allocate that dynamically and be not
implicitly dependent on verifier mutex. Move bpf_prog_calc_digest() at
the beginning of replace_map_fd_with_map_ptr() and also error handling
stays straight forward.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 57a09bf0a4 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL
registers") introduced a regression where existing programs stopped
loading due to reaching the verifier's maximum complexity limit,
whereas prior to this commit they were loading just fine; the affected
program has roughly 2k instructions.
What was found is that state pruning couldn't be performed effectively
anymore due to mismatches of the verifier's register state, in particular
in the id tracking. It doesn't mean that 57a09bf0a4 is incorrect per
se, but rather that verifier needs to perform a lot more work for the
same program with regards to involved map lookups.
Since commit 57a09bf0a4 is only about tracking registers with type
PTR_TO_MAP_VALUE_OR_NULL, the id is only needed to follow registers
until they are promoted through pattern matching with a NULL check to
either PTR_TO_MAP_VALUE or UNKNOWN_VALUE type. After that point, the
id becomes irrelevant for the transitioned types.
For UNKNOWN_VALUE, id is already reset to 0 via mark_reg_unknown_value(),
but not so for PTR_TO_MAP_VALUE where id is becoming stale. It's even
transferred further into other types that don't make use of it. Among
others, one example is where UNKNOWN_VALUE is set on function call
return with RET_INTEGER return type.
states_equal() will then fall through the memcmp() on register state;
note that the second memcmp() uses offsetofend(), so the id is part of
that since d2a4dd37f6 ("bpf: fix state equivalence"). But the bisect
pointed already to 57a09bf0a4, where we really reach beyond complexity
limit. What I found was that states_equal() often failed in this
case due to id mismatches in spilled regs with registers in type
PTR_TO_MAP_VALUE. Unlike non-spilled regs, spilled regs just perform
a memcmp() on their reg state and don't have any other optimizations
in place, therefore also id was relevant in this case for making a
pruning decision.
We can safely reset id to 0 as well when converting to PTR_TO_MAP_VALUE.
For the affected program, it resulted in a ~17 fold reduction of
complexity and let the program load fine again. Selftest suite also
runs fine. The only other place where env->id_gen is used currently is
through direct packet access, but for these cases id is long living, thus
a different scenario.
Also, the current logic in mark_map_regs() is not fully correct when
marking NULL branch with UNKNOWN_VALUE. We need to cache the destination
reg's id in any case. Otherwise, once we marked that reg as UNKNOWN_VALUE,
it's id is reset and any subsequent registers that hold the original id
and are of type PTR_TO_MAP_VALUE_OR_NULL won't be marked UNKNOWN_VALUE
anymore, since mark_map_reg() reuses the uncached regs[regno].id that
was just overridden. Note, we don't need to cache it outside of
mark_map_regs(), since it's called once on this_branch and the other
time on other_branch, which are both two independent verifier states.
A test case for this is added here, too.
Fixes: 57a09bf0a4 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows XDP prog to extend/remove the packet
data at the head (like adding or removing header). It is
done by adding a new XDP helper bpf_xdp_adjust_head().
It also renames bpf_helper_changes_skb_data() to
bpf_helper_changes_pkt_data() to better reflect
that XDP prog does not work on skb.
This patch adds one "xdp_adjust_head" bit to bpf_prog for the
XDP-capable driver to check if the XDP prog requires
bpf_xdp_adjust_head() support. The driver can then decide
to error out during XDP_SETUP_PROG.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commmits 57a09bf0a4 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers")
and 484611357c ("bpf: allow access into map value arrays") by themselves
are correct, but in combination they make state equivalence ignore 'id' field
of the register state which can lead to accepting invalid program.
Fixes: 57a09bf0a4 ("bpf: Detect identical PTR_TO_MAP_VALUE_OR_NULL registers")
Fixes: 484611357c ("bpf: allow access into map value arrays")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
General assumption is that single program can hold up to BPF_MAXINSNS,
that is, 4096 number of instructions. It is the case with cBPF and
that limit was carried over to eBPF. When recently testing digest, I
noticed that it's actually not possible to feed 4096 instructions
via bpf(2).
The check for > BPF_MAXINSNS was added back then to bpf_check() in
cbd3570086 ("bpf: verifier (add ability to receive verification log)").
However, 09756af468 ("bpf: expand BPF syscall with program load/unload")
added yet another check that comes before that into bpf_prog_load(),
but this time bails out already in case of >= BPF_MAXINSNS.
Fix it up and perform the check early in bpf_prog_load(), so we can drop
the second one in bpf_check(). It makes sense, because also a 0 insn
program is useless and we don't want to waste any resources doing work
up to bpf_check() point. The existing bpf(2) man page documents E2BIG
as the official error for such cases, so just stick with it as well.
Fixes: 09756af468 ("bpf: expand BPF syscall with program load/unload")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading a BPF program via bpf(2), calculate the digest over
the program's instruction stream and store it in struct bpf_prog's
digest member. This is done at a point in time before any instructions
are rewritten by the verifier. Any unstable map file descriptor
number part of the imm field will be zeroed for the hash.
fdinfo example output for progs:
# cat /proc/1590/fdinfo/5
pos: 0
flags: 02000002
mnt_id: 11
prog_type: 1
prog_jited: 1
prog_digest: b27e8b06da22707513aa97363dfb11c7c3675d28
memlock: 4096
When programs are pinned and retrieved by an ELF loader, the loader
can check the program's digest through fdinfo and compare it against
one that was generated over the ELF file's program section to see
if the program needs to be reloaded. Furthermore, this can also be
exposed through other means such as netlink in case of a tc cls/act
dump (or xdp in future), but also through tracepoints or other
facilities to identify the program. Other than that, the digest can
also serve as a base name for the work in progress kallsyms support
of programs. The digest doesn't depend/select the crypto layer, since
we need to keep dependencies to a minimum. iproute2 will get support
for this facility.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally, clang (e.g. version 3.8.1) translates a sum between two
constant operands using a BPF_OR instead of a BPF_ADD. The verifier is
currently not handling this scenario, and the destination register type
becomes UNKNOWN_VALUE even if it's still storing a constant. As a result,
the destination register cannot be used as argument to a helper function
expecting a ARG_CONST_STACK_*, limiting some use cases.
Modify the verifier to handle this case, and add a few tests to make sure
all combinations are supported, and stack boundaries are still verified
even with BPF_OR.
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new cgroup based program type, BPF_PROG_TYPE_CGROUP_SOCK. Similar to
BPF_PROG_TYPE_CGROUP_SKB programs can be attached to a cgroup and run
any time a process in the cgroup opens an AF_INET or AF_INET6 socket.
Currently only sk_bound_dev_if is exported to userspace for modification
by a bpf program.
This allows a cgroup to be configured such that AF_INET{6} sockets opened
by processes are automatically bound to a specific device. In turn, this
enables the running of programs that do not support SO_BINDTODEVICE in a
specific VRF context / L3 domain.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code move and rename only; no functional change intended.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Registers new BPF program types which correspond to the LWT hooks:
- BPF_PROG_TYPE_LWT_IN => dst_input()
- BPF_PROG_TYPE_LWT_OUT => dst_output()
- BPF_PROG_TYPE_LWT_XMIT => lwtunnel_xmit()
The separate program types are required to differentiate between the
capabilities each LWT hook allows:
* Programs attached to dst_input() or dst_output() are restricted and
may only read the data of an skb. This prevent modification and
possible invalidation of already validated packet headers on receive
and the construction of illegal headers while the IP headers are
still being assembled.
* Programs attached to lwtunnel_xmit() are allowed to modify packet
content as well as prepending an L2 header via a newly introduced
helper bpf_skb_change_head(). This is safe as lwtunnel_xmit() is
invoked after the IP header has been assembled completely.
All BPF programs receive an skb with L3 headers attached and may return
one of the following error codes:
BPF_OK - Continue routing as per nexthop
BPF_DROP - Drop skb and return EPERM
BPF_REDIRECT - Redirect skb to device as per redirect() helper.
(Only valid in lwtunnel_xmit() context)
The return codes are binary compatible with their TC_ACT_
relatives to ease compatibility.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have a branch that looks something like this
int foo = map->value;
if (condition) {
foo += blah;
} else {
foo = bar;
}
map->array[foo] = baz;
We will incorrectly assume that the !condition branch is equal to the condition
branch as the register for foo will be UNKNOWN_VALUE in both cases. We need to
adjust this logic to only do this if we didn't do a varlen access after we
processed the !condition branch, otherwise we have different ranges and need to
check the other branch as well.
Fixes: 484611357c ("bpf: allow access into map value arrays")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a 'not' missing in one paragraph. Add it.
Fixes: 3007098494 ("cgroup: add support for eBPF programs")
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reported-by: Rami Rosen <roszenrami@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we recently converted the BPF filesystem over to use mount_nodev(),
we now have the possibility to also hold mount options in sb's s_fs_info.
This work implements mount options support for specifying permissions on
the sb's inode, which will be used by tc when it manually needs to mount
the fs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow for checking the owner_prog_type of a program array map. In some
cases bpf(2) can return -EINVAL /after/ the verifier passed and did all
the rewrites of the bpf program.
The reason that lets us fail at this late stage is that program array
maps are incompatible. Allow users to inspect this earlier after they
got the map fd through BPF_OBJ_GET command. tc will get support for this.
Also, display how much we charged the map with regards to RLIMIT_MEMLOCK.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the bpf(2) syscall by two new commands, BPF_PROG_ATTACH and
BPF_PROG_DETACH which allow attaching and detaching eBPF programs
to a target.
On the API level, the target could be anything that has an fd in
userspace, hence the name of the field in union bpf_attr is called
'target_fd'.
When called with BPF_ATTACH_TYPE_CGROUP_INET_{E,IN}GRESS, the target is
expected to be a valid file descriptor of a cgroup v2 directory which
has the bpf controller enabled. These are the only use-cases
implemented by this patch at this point, but more can be added.
If a program of the given type already exists in the given cgroup,
the program is swapped automically, so userspace does not have to drop
an existing program first before installing a new one, which would
otherwise leave a gap in which no program is attached.
For more information on the propagation logic to subcgroups, please
refer to the bpf cgroup controller implementation.
The API is guarded by CAP_NET_ADMIN.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two sets of eBPF program pointers to struct cgroup.
One for such that are directly pinned to a cgroup, and one for such
that are effective for it.
To illustrate the logic behind that, assume the following example
cgroup hierarchy.
A - B - C
\ D - E
If only B has a program attached, it will be effective for B, C, D
and E. If D then attaches a program itself, that will be effective for
both D and E, and the program in B will only affect B and C. Only one
program of a given type is effective for a cgroup.
Attaching and detaching programs will be done through the bpf(2)
syscall. For now, ingress and egress inet socket filtering are the
only supported use-cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlx5e_create_rq(), when creating a new queue, we call bpf_prog_add() but
without checking the return value. bpf_prog_add() can fail since 92117d8443
("bpf: fix refcnt overflow"), so we really must check it. Take the reference
right when we assign it to the rq from priv->xdp_prog, and just drop the
reference on error path. Destruction in mlx5e_destroy_rq() looks good, though.
Fixes: 86994156c7 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I made some invalid assumptions with BPF_AND and BPF_MOD that could result in
invalid accesses to bpf map entries. Fix this up by doing a few things
1) Kill BPF_MOD support. This doesn't actually get used by the compiler in real
life and just adds extra complexity.
2) Fix the logic for BPF_AND, don't allow AND of negative numbers and set the
minimum value to 0 for positive AND's.
3) Don't do operations on the ranges if they are set to the limits, as they are
by definition undefined, and allowing arithmetic operations on those values
could make them appear valid when they really aren't.
This fixes the testcase provided by Jann as well as a few other theoretical
problems.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-6.2.1 gives the following warning:
kernel/bpf/bpf_lru_list.c: In function ‘__bpf_lru_list_rotate_inactive.isra.3’:
kernel/bpf/bpf_lru_list.c:201:28: warning: ‘next’ may be used uninitialized in this function [-Wmaybe-uninitialized]
The "next" is currently initialized in the while() loop which must have >=1
iterations.
This patch initializes next to get rid of the compiler warning.
Fixes: 3a08c2fd76 ("bpf: LRU List")
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a LRU version of the existing BPF_MAP_TYPE_PERCPU_HASH
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a LRU version of the existing BPF_MAP_TYPE_HASH.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the codes that populate the value
of a htab_elem in a BPF_MAP_TYPE_PERCPU_HASH
typed bpf_map.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having a common LRU list, this patch allows a
percpu LRU list which can be selected by specifying a map
attribute. The map attribute will be added in the later
patch.
While the common use case for LRU is #reads >> #updates,
percpu LRU list allows bpf prog to absorb unusual #updates
under pathological case (e.g. external traffic facing machine which
could be under attack).
Each percpu LRU is isolated from each other. The LRU nodes (including
free nodes) cannot be moved across different LRU Lists.
Here are the update performance comparison between
common LRU list and percpu LRU list (the test code is
at the last patch):
[root@kerneltest003.31.prn1 ~]# for i in 1 4 8; do echo -n "$i cpus: "; \
./map_perf_test 16 $i | awk '{r += $3}END{print r " updates"}'; done
1 cpus: 2934082 updates
4 cpus: 7391434 updates
8 cpus: 6500576 updates
[root@kerneltest003.31.prn1 ~]# for i in 1 4 8; do echo -n "$i cpus: "; \
./map_perf_test 32 $i | awk '{r += $3}END{printr " updates"}'; done
1 cpus: 2896553 updates
4 cpus: 9766395 updates
8 cpus: 17460553 updates
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce bpf_lru_list which will provide LRU capability to
the bpf_htab in the later patch.
* General Thoughts:
1. Target use case. Read is more often than update.
(i.e. bpf_lookup_elem() is more often than bpf_update_elem()).
If bpf_prog does a bpf_lookup_elem() first and then an in-place
update, it still counts as a read operation to the LRU list concern.
2. It may be useful to think of it as a LRU cache
3. Optimize the read case
3.1 No lock in read case
3.2 The LRU maintenance is only done during bpf_update_elem()
4. If there is a percpu LRU list, it will lose the system-wise LRU
property. A completely isolated percpu LRU list has the best
performance but the memory utilization is not ideal considering
the work load may be imbalance.
5. Hence, this patch starts the LRU implementation with a global LRU
list with batched operations before accessing the global LRU list.
As a LRU cache, #read >> #update/#insert operations, it will work well.
6. There is a local list (for each cpu) which is named
'struct bpf_lru_locallist'. This local list is not used to sort
the LRU property. Instead, the local list is to batch enough
operations before acquiring the lock of the global LRU list. More
details on this later.
7. In the later patch, it allows a percpu LRU list by specifying a
map-attribute for scalability reason and for use cases that need to
prepare for the worst (and pathological) case like DoS attack.
The percpu LRU list is completely isolated from each other and the
LRU nodes (including free nodes) cannot be moved across the list. The
following description is for the global LRU list but mostly applicable
to the percpu LRU list also.
* Global LRU List:
1. It has three sub-lists: active-list, inactive-list and free-list.
2. The two list idea, active and inactive, is borrowed from the
page cache.
3. All nodes are pre-allocated and all sit at the free-list (of the
global LRU list) at the beginning. The pre-allocation reasoning
is similar to the existing BPF_MAP_TYPE_HASH. However,
opting-out prealloc (BPF_F_NO_PREALLOC) is not supported in
the LRU map.
* Active/Inactive List (of the global LRU list):
1. The active list, as its name says it, maintains the active set of
the nodes. We can think of it as the working set or more frequently
accessed nodes. The access frequency is approximated by a ref-bit.
The ref-bit is set during the bpf_lookup_elem().
2. The inactive list, as its name also says it, maintains a less
active set of nodes. They are the candidates to be removed
from the bpf_htab when we are running out of free nodes.
3. The ordering of these two lists is acting as a rough clock.
The tail of the inactive list is the older nodes and
should be released first if the bpf_htab needs free element.
* Rotating the Active/Inactive List (of the global LRU list):
1. It is the basic operation to maintain the LRU property of
the global list.
2. The active list is only rotated when the inactive list is running
low. This idea is similar to the current page cache.
Inactive running low is currently defined as
"# of inactive < # of active".
3. The active list rotation always starts from the tail. It moves
node without ref-bit set to the head of the inactive list.
It moves node with ref-bit set back to the head of the active
list and then clears its ref-bit.
4. The inactive rotation is pretty simply.
It walks the inactive list and moves the nodes back to the head of
active list if its ref-bit is set. The ref-bit is cleared after moving
to the active list.
If the node does not have ref-bit set, it just leave it as it is
because it is already in the inactive list.
* Shrinking the Inactive List (of the global LRU list):
1. Shrinking is the operation to get free nodes when the bpf_htab is
full.
2. It usually only shrinks the inactive list to get free nodes.
3. During shrinking, it will walk the inactive list from the tail,
delete the nodes without ref-bit set from bpf_htab.
4. If no free node found after step (3), it will forcefully get
one node from the tail of inactive or active list. Forcefully is
in the sense that it ignores the ref-bit.
* Local List:
1. Each CPU has a 'struct bpf_lru_locallist'. The purpose is to
batch enough operations before acquiring the lock of the
global LRU.
2. A local list has two sub-lists, free-list and pending-list.
3. During bpf_update_elem(), it will try to get from the free-list
of (the current CPU local list).
4. If the local free-list is empty, it will acquire from the
global LRU list. The global LRU list can either satisfy it
by its global free-list or by shrinking the global inactive
list. Since we have acquired the global LRU list lock,
it will try to get at most LOCAL_FREE_TARGET elements
to the local free list.
5. When a new element is added to the bpf_htab, it will
first sit at the pending-list (of the local list) first.
The pending-list will be flushed to the global LRU list
when it needs to acquire free nodes from the global list
next time.
* Lock Consideration:
The LRU list has a lock (lru_lock). Each bucket of htab has a
lock (buck_lock). If both locks need to be acquired together,
the lock order is always lru_lock -> buck_lock and this only
happens in the bpf_lru_list.c logic.
In hashtab.c, both locks are not acquired together (i.e. one
lock is always released first before acquiring another lock).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the custom u64_to_ptr() function with the u64_to_user_ptr()
macro.
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 67f8b1dcb9 ("net/mlx4_en: Refactor the XDP forwarding rings
scheme") added a bug in that the prog's reference count is not dropped
in the error path when mlx4_en_try_alloc_resources() is failing from
mlx4_xdp_set().
We previously took bpf_prog_add(prog, priv->rx_ring_num - 1), that we
need to release again. Earlier in the call path, dev_change_xdp_fd()
itself holds a reference to the prog as well (hence the '- 1' in the
bpf_prog_add()), so a simple atomic_sub() is safe to use here. When
an error is propagated, then bpf_prog_put() is called eventually from
dev_change_xdp_fd()
Fixes: 67f8b1dcb9 ("net/mlx4_en: Refactor the XDP forwarding rings scheme")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unused but set variables min_set and max_set in
adjust_reg_min_max_vals to fix the following warning when building with
'W=1':
kernel/bpf/verifier.c:1483:7: warning: variable ‘min_set’ set but not used [-Wunused-but-set-variable]
There is no warning about max_set being unused, but since it is only
used in the assignment of min_set it can be removed as well.
They were introduced in commit 484611357c ("bpf: allow access into map
value arrays") but seem to have never been used.
Cc: Josef Bacik <jbacik@fb.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In map_create(), we first find and create the map, then once that
suceeded, we charge it to the user's RLIMIT_MEMLOCK, and then fetch
a new anon fd through anon_inode_getfd(). The problem is, once the
latter fails f.e. due to RLIMIT_NOFILE limit, then we only destruct
the map via map->ops->map_free(), but without uncharging the previously
locked memory first. That means that the user_struct allocation is
leaked as well as the accounted RLIMIT_MEMLOCK memory not released.
Make the label names in the fix consistent with bpf_prog_load().
Fixes: aaac3ba95e ("bpf: charge user for creation of BPF maps and programs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a6ed3ea65d ("bpf: restore behavior of bpf_map_update_elem")
added an extra per-cpu reserve to the hash table map to restore old
behaviour from pre prealloc times. When non-prealloc is in use for a
map, then problem is that once a hash table extra element has been
linked into the hash-table, and the hash table is destroyed due to
refcount dropping to zero, then htab_map_free() -> delete_all_elements()
will walk the whole hash table and drop all elements via htab_elem_free().
The problem is that the element from the extra reserve is first fed
to the wrong backend allocator and eventually freed twice.
Fixes: a6ed3ea65d ("bpf: restore behavior of bpf_map_update_elem")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While commit bb35a6ef7d ("bpf, inode: allow for rename and link ops")
added support for hard links that can be used for prog and map nodes,
this work adds simple symlink support, which can be used f.e. for
directories also when unpriviledged and works with cmdline tooling that
understands S_IFLNK anyway. Since the switch in e27f4a942a ("bpf: Use
mount_nodev not mount_ns to mount the bpf filesystem"), there can be
various mount instances with mount_nodev() and thus hierarchy can be
flattened to facilitate object sharing. Thus, we can keep bpf tooling
also working by repointing paths.
Most of the functionality can be used from vfs library operations. The
symlink is stored in the inode itself, that is in i_link, which is
sufficient in our case as opposed to storing it in the page cache.
While at it, I noticed that bpf_mkdir() and bpf_mkobj() don't update
the directories mtime and ctime, so add a common helper for it called
bpf_dentry_finalize() that takes care of it for all cases now.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The verifier currently prints raw function ids when printing CALL
instructions or when complaining:
5: (85) call 23
unknown func 23
print a meaningful function name instead:
5: (85) call bpf_redirect#23
unknown func bpf_redirect#23
Moves the function documentation to a single comment and renames all
helpers names in the list to conform to the bpf_ prefix notation so
they can be greped in the kernel source.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use case is mainly for soreuseport to select sockets for the local
numa node, but since generic, lets also add this for other networking
and tracing program types.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A BPF program is required to check the return register of a
map_elem_lookup() call before accessing memory. The verifier keeps
track of this by converting the type of the result register from
PTR_TO_MAP_VALUE_OR_NULL to PTR_TO_MAP_VALUE after a conditional
jump ensures safety. This check is currently exclusively performed
for the result register 0.
In the event the compiler reorders instructions, BPF_MOV64_REG
instructions may be moved before the conditional jump which causes
them to keep their type PTR_TO_MAP_VALUE_OR_NULL to which the
verifier objects when the register is accessed:
0: (b7) r1 = 10
1: (7b) *(u64 *)(r10 -8) = r1
2: (bf) r2 = r10
3: (07) r2 += -8
4: (18) r1 = 0x59c00000
6: (85) call 1
7: (bf) r4 = r0
8: (15) if r0 == 0x0 goto pc+1
R0=map_value(ks=8,vs=8) R4=map_value_or_null(ks=8,vs=8) R10=fp
9: (7a) *(u64 *)(r4 +0) = 0
R4 invalid mem access 'map_value_or_null'
This commit extends the verifier to keep track of all identical
PTR_TO_MAP_VALUE_OR_NULL registers after a map_elem_lookup() by
assigning them an ID and then marking them all when the conditional
jump is observed.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more vfs updates from Al Viro:
">rename2() work from Miklos + current_time() from Deepa"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Replace current_fs_time() with current_time()
fs: Replace CURRENT_TIME_SEC with current_time() for inode timestamps
fs: Replace CURRENT_TIME with current_time() for inode timestamps
fs: proc: Delete inode time initializations in proc_alloc_inode()
vfs: Add current_time() api
vfs: add note about i_op->rename changes to porting
fs: rename "rename2" i_op to "rename"
vfs: remove unused i_op->rename
fs: make remaining filesystems use .rename2
libfs: support RENAME_NOREPLACE in simple_rename()
fs: support RENAME_NOREPLACE for local filesystems
ncpfs: fix unused variable warning
Suppose you have a map array value that is something like this
struct foo {
unsigned iter;
int array[SOME_CONSTANT];
};
You can easily insert this into an array, but you cannot modify the contents of
foo->array[] after the fact. This is because we have no way to verify we won't
go off the end of the array at verification time. This patch provides a start
for this work. We accomplish this by keeping track of a minimum and maximum
value a register could be while we're checking the code. Then at the time we
try to do an access into a MAP_VALUE we verify that the maximum offset into that
region is a valid access into that memory region. So in practice, code such as
this
unsigned index = 0;
if (foo->iter >= SOME_CONSTANT)
foo->iter = index;
else
index = foo->iter++;
foo->array[index] = bar;
would be allowed, as we can verify that index will always be between 0 and
SOME_CONSTANT-1. If you wish to use signed values you'll have to have an extra
check to make sure the index isn't less than 0, or do something like index %=
SOME_CONSTANT.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
put_cpu_var takes the percpu data, not the data returned from
get_cpu_var.
This doesn't change the behavior.
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CURRENT_TIME macro is not appropriate for filesystems as it
doesn't use the right granularity for filesystem timestamps.
Use current_time() instead.
CURRENT_TIME is also not y2038 safe.
This is also in preparation for the patch that transitions
vfs timestamps to use 64 bit time and hence make them
y2038 safe. As part of the effort current_time() will be
extended to do range checks. Hence, it is necessary for all
file system timestamps to use current_time(). Also,
current_time() will be transitioned along with vfs to be
y2038 safe.
Note that whenever a single call to current_time() is used
to change timestamps in different inodes, it is because they
share the same time granularity.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This prevent future potential pointer leaks when an unprivileged eBPF
program will read a pointer value from its context. Even if
is_valid_access() returns a pointer type, the eBPF verifier replace it
with UNKNOWN_VALUE. The register value that contains a kernel address is
then allowed to leak. Moreover, this fix allows unprivileged eBPF
programs to use functions with (legitimate) pointer arguments.
Not an issue currently since reg_type is only set for PTR_TO_PACKET or
PTR_TO_PACKET_END in XDP and TC programs that can only be loaded as
privileged. For now, the only unprivileged eBPF program allowed is for
socket filtering and all the types from its context are UNKNOWN_VALUE.
However, this fix is important for future unprivileged eBPF programs
which could use pointers in their context.
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running as parser interpret BPF_LD | BPF_IMM | BPF_DW
instructions as loading CONST_IMM with the value stored
in imm. The verifier will continue not recognizing those
due to concerns about search space/program complexity
increase.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advanced JIT compilers and translators may want to use
eBPF verifier as a base for parsers or to perform custom
checks and validations.
Add ability for external users to invoke the verifier
and provide callbacks to be invoked for every intruction
checked. For now only add most basic callback for
per-instruction pre-interpretation checks is added. More
advanced users may also like to have per-instruction post
callback and state comparison callback.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move verifier's internal structures to a header file and
prefix their names with bpf_ to avoid potential namespace
conflicts. Those structures will soon be used by external
analyzers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storing state in reserved fields of instructions makes
it impossible to run verifier on programs already
marked as read-only. Allocate and use an array of
per-instruction state instead.
While touching the error path rename and move existing
jump target.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work implements direct packet access for helpers and direct packet
write in a similar fashion as already available for XDP types via commits
4acf6c0b84 ("bpf: enable direct packet data write for xdp progs") and
6841de8b0d ("bpf: allow helpers access the packet directly"), and as a
complementary feature to the already available direct packet read for tc
(cls/act) programs.
For enabling this, we need to introduce two helpers, bpf_skb_pull_data()
and bpf_csum_update(). The first is generally needed for both, read and
write, because they would otherwise only be limited to the current linear
skb head. Usually, when the data_end test fails, programs just bail out,
or, in the direct read case, use bpf_skb_load_bytes() as an alternative
to overcome this limitation. If such data sits in non-linear parts, we
can just pull them in once with the new helper, retest and eventually
access them.
At the same time, this also makes sure the skb is uncloned, which is, of
course, a necessary condition for direct write. As this needs to be an
invariant for the write part only, the verifier detects writes and adds
a prologue that is calling bpf_skb_pull_data() to effectively unclone the
skb from the very beginning in case it is indeed cloned. The heuristic
makes use of a similar trick that was done in 233577a220 ("net: filter:
constify detection of pkt_type_offset"). This comes at zero cost for other
programs that do not use the direct write feature. Should a program use
this feature only sparsely and has read access for the most parts with,
for example, drop return codes, then such write action can be delegated
to a tail called program for mitigating this cost of potential uncloning
to a late point in time where it would have been paid similarly with the
bpf_skb_store_bytes() as well. Advantage of direct write is that the
writes are inlined whereas the helper cannot make any length assumptions
and thus needs to generate a call to memcpy() also for small sizes, as well
as cost of helper call itself with sanity checks are avoided. Plus, when
direct read is already used, we don't need to cache or perform rechecks
on the data boundaries (due to verifier invalidating previous checks for
helpers that change skb->data), so more complex programs using rewrites
can benefit from switching to direct read plus write.
For direct packet access to helpers, we save the otherwise needed copy into
a temp struct sitting on stack memory when use-case allows. Both facilities
are enabled via may_access_direct_pkt_data() in verifier. For now, we limit
this to map helpers and csum_diff, and can successively enable other helpers
where we find it makes sense. Helpers that definitely cannot be allowed for
this are those part of bpf_helper_changes_skb_data() since they can change
underlying data, and those that write into memory as this could happen for
packet typed args when still cloned. bpf_csum_update() helper accommodates
for the fact that we need to fixup checksum_complete when using direct write
instead of bpf_skb_store_bytes(), meaning the programs can use available
helpers like bpf_csum_diff(), and implement csum_add(), csum_sub(),
csum_block_add(), csum_block_sub() equivalents in eBPF together with the
new helper. A usage example will be provided for iproute2's examples/bpf/
directory.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current contract for the following two helper argument types is:
* ARG_CONST_STACK_SIZE: passed argument pair must be (ptr, >0).
* ARG_CONST_STACK_SIZE_OR_ZERO: passed argument pair can be either
(NULL, 0) or (ptr, >0).
With 6841de8b0d ("bpf: allow helpers access the packet directly"), we can
pass also raw packet data to helpers, so depending on the argument type
being PTR_TO_PACKET, we now either assert memory via check_packet_access()
or check_stack_boundary(). As a result, the tests in check_packet_access()
currently allow more than intended with regards to reg->imm.
Back in 969bf05eb3 ("bpf: direct packet access"), check_packet_access()
was fine to ignore size argument since in check_mem_access() size was
bpf_size_to_bytes() derived and prior to the call to check_packet_access()
guaranteed to be larger than zero.
However, for the above two argument types, it currently means, we can have
a <= 0 size and thus breaking current guarantees for helpers. Enforce a
check for size <= 0 and bail out if so.
check_stack_boundary() doesn't have such an issue since it already tests
for access_size <= 0 and bails out, resp. access_size == 0 in case of NULL
pointer passed when allowed.
Fixes: 6841de8b0d ("bpf: allow helpers access the packet directly")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds BPF_CALL_<n>() macros and converts all the eBPF helper functions
to use them, in a similar fashion like we do with SYSCALL_DEFINE<n>() macros
that are used today. Motivation for this is to hide all the register handling
and all necessary casts from the user, so that it is done automatically in the
background when adding a BPF_CALL_<n>() call.
This makes current helpers easier to review, eases to write future helpers,
avoids getting the casting mess wrong, and allows for extending all helpers at
once (f.e. build time checks, etc). It also helps detecting more easily in
code reviews that unused registers are not instrumented in the code by accident,
breaking compatibility with existing programs.
BPF_CALL_<n>() internals are quite similar to SYSCALL_DEFINE<n>() ones with some
fundamental differences, for example, for generating the actual helper function
that carries all u64 regs, we need to fill unused regs, so that we always end up
with 5 u64 regs as an argument.
I reviewed several 0-5 generated BPF_CALL_<n>() variants of the .i results and
they look all as expected. No sparse issue spotted. We let this also sit for a
few days with Fengguang's kbuild test robot, and there were no issues seen. On
s390, it barked on the "uses dynamic stack allocation" notice, which is an old
one from bpf_perf_event_output{,_tp}() reappearing here due to the conversion
to the call wrapper, just telling that the perf raw record/frag sits on stack
(gcc with s390's -mwarn-dynamicstack), but that's all. Did various runtime tests
and they were fine as well. All eBPF helpers are now converted to use these
macros, getting rid of a good chunk of all the raw castings.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor misc cleanups, f.e. use sizeof(__u32) instead of hardcoding
and in __bpf_skb_max_len(), I missed that we always have skb->dev valid
anyway, so we can drop the unneeded test for dev; also few more other
misc bits addressed here.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
LLVM can generate code that tests for direct packet access via
skb->data/data_end in a way that currently gets rejected by the
verifier, example:
[...]
7: (61) r3 = *(u32 *)(r6 +80)
8: (61) r9 = *(u32 *)(r6 +76)
9: (bf) r2 = r9
10: (07) r2 += 54
11: (3d) if r3 >= r2 goto pc+12
R1=inv R2=pkt(id=0,off=54,r=0) R3=pkt_end R4=inv R6=ctx
R9=pkt(id=0,off=0,r=0) R10=fp
12: (18) r4 = 0xffffff7a
14: (05) goto pc+430
[...]
from 11 to 24: R1=inv R2=pkt(id=0,off=54,r=0) R3=pkt_end R4=inv
R6=ctx R9=pkt(id=0,off=0,r=0) R10=fp
24: (7b) *(u64 *)(r10 -40) = r1
25: (b7) r1 = 0
26: (63) *(u32 *)(r6 +56) = r1
27: (b7) r2 = 40
28: (71) r8 = *(u8 *)(r9 +20)
invalid access to packet, off=20 size=1, R9(id=0,off=0,r=0)
The reason why this gets rejected despite a proper test is that we
currently call find_good_pkt_pointers() only in case where we detect
tests like rX > pkt_end, where rX is of type pkt(id=Y,off=Z,r=0) and
derived, for example, from a register of type pkt(id=Y,off=0,r=0)
pointing to skb->data. find_good_pkt_pointers() then fills the range
in the current branch to pkt(id=Y,off=0,r=Z) on success.
For above case, we need to extend that to recognize pkt_end >= rX
pattern and mark the other branch that is taken on success with the
appropriate pkt(id=Y,off=0,r=Z) type via find_good_pkt_pointers().
Since eBPF operates on BPF_JGT (>) and BPF_JGE (>=), these are the
only two practical options to test for from what LLVM could have
generated, since there's no such thing as BPF_JLT (<) or BPF_JLE (<=)
that we would need to take into account as well.
After the fix:
[...]
7: (61) r3 = *(u32 *)(r6 +80)
8: (61) r9 = *(u32 *)(r6 +76)
9: (bf) r2 = r9
10: (07) r2 += 54
11: (3d) if r3 >= r2 goto pc+12
R1=inv R2=pkt(id=0,off=54,r=0) R3=pkt_end R4=inv R6=ctx
R9=pkt(id=0,off=0,r=0) R10=fp
12: (18) r4 = 0xffffff7a
14: (05) goto pc+430
[...]
from 11 to 24: R1=inv R2=pkt(id=0,off=54,r=54) R3=pkt_end R4=inv
R6=ctx R9=pkt(id=0,off=0,r=54) R10=fp
24: (7b) *(u64 *)(r10 -40) = r1
25: (b7) r1 = 0
26: (63) *(u32 *)(r6 +56) = r1
27: (b7) r2 = 40
28: (71) r8 = *(u8 *)(r9 +20)
29: (bf) r1 = r8
30: (25) if r8 > 0x3c goto pc+47
R1=inv56 R2=imm40 R3=pkt_end R4=inv R6=ctx R8=inv56
R9=pkt(id=0,off=0,r=54) R10=fp
31: (b7) r1 = 1
[...]
Verifier test cases are also added in this work, one that demonstrates
the mentioned example here and one that tries a bad packet access for
the current/fall-through branch (the one with types pkt(id=X,off=Y,r=0),
pkt(id=X,off=0,r=0)), then a case with good and bad accesses, and two
with both test variants (>, >=).
Fixes: 969bf05eb3 ("bpf: direct packet access")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that BPF_PROG_TYPE_PERF_EVENT programs only use
preallocated hash maps, since doing memory allocation
in overflow_handler can crash depending on where nmi got triggered.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The verifier supported only 4-byte metafields in
struct __sk_buff and struct xdp_md. The metafields in upcoming
struct bpf_perf_event are 8-byte to match register width in struct pt_regs.
Teach verifier to recognize 8-byte metafield access.
The patch doesn't affect safety of sockets and xdp programs.
They check for 4-byte only ctx access before these conditions are hit.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper functions like bpf_map_lookup_elem(map, key) were only
allowing 'key' to point to the initialized stack area.
That is causing performance degradation when programs need to process
millions of packets per second and need to copy contents of the packet
into the stack just to pass the stack pointer into the lookup() function.
Allow such helpers read from the packet directly.
All helpers that expect ARG_PTR_TO_MAP_KEY, ARG_PTR_TO_MAP_VALUE,
ARG_PTR_TO_STACK assume byte aligned pointer, so no alignment concerns,
only need to check that helper will not be accessing beyond
the packet range verified by the prior 'if (ptr < data_end)' condition.
For now allow this feature for XDP programs only. Later it can be
relaxed for the clsact programs as well.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
While hashing out BPF's current_task_under_cgroup helper bits, it came
to discussion that the skb_in_cgroup helper name was suboptimally chosen.
Tejun says:
So, I think in_cgroup should mean that the object is in that
particular cgroup while under_cgroup in the subhierarchy of that
cgroup. Let's rename the other subhierarchy test to under too. I
think that'd be a lot less confusing going forward.
[...]
It's more intuitive and gives us the room to implement the real
"in" test if ever necessary in the future.
Since this touches uapi bits, we need to change this as long as v4.8
is not yet officially released. Thus, change the helper enum and rename
related bits.
Fixes: 4a482f34af ("cgroup: bpf: Add bpf_skb_in_cgroup_proto")
Reference: http://patchwork.ozlabs.org/patch/658500/
Suggested-by: Sargun Dhillon <sargun@sargun.me>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
This adds a bpf helper that's similar to the skb_in_cgroup helper to check
whether the probe is currently executing in the context of a specific
subset of the cgroupsv2 hierarchy. It does this based on membership test
for a cgroup arraymap. It is invalid to call this in an interrupt, and
it'll return an error. The helper is primarily to be used in debugging
activities for containers, where you may have multiple programs running in
a given top-level "container".
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The introduction of pre-allocated hash elements inadvertently broke
the behavior of bpf hash maps where users expected to call
bpf_map_update_elem() without considering that the map can be full.
Some programs do:
old_value = bpf_map_lookup_elem(map, key);
if (old_value) {
... prepare new_value on stack ...
bpf_map_update_elem(map, key, new_value);
}
Before pre-alloc the update() for existing element would work even
in 'map full' condition. Restore this behavior.
The above program could have updated old_value in place instead of
update() which would be faster and most programs use that approach,
but sometimes the values are large and the programs use update()
helper to do atomic replacement of the element.
Note we cannot simply update element's value in-place like percpu
hash map does and have to allocate extra num_possible_cpu elements
and use this extra reserve when the map is full.
Fixes: 6c90598174 ("bpf: pre-allocate hash map elements")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using per-register incrementing ID can lead to
find_good_pkt_pointers() confusing registers which
have completely different values. Consider example:
0: (bf) r6 = r1
1: (61) r8 = *(u32 *)(r6 +76)
2: (61) r0 = *(u32 *)(r6 +80)
3: (bf) r7 = r8
4: (07) r8 += 32
5: (2d) if r8 > r0 goto pc+9
R0=pkt_end R1=ctx R6=ctx R7=pkt(id=0,off=0,r=32) R8=pkt(id=0,off=32,r=32) R10=fp
6: (bf) r8 = r7
7: (bf) r9 = r7
8: (71) r1 = *(u8 *)(r7 +0)
9: (0f) r8 += r1
10: (71) r1 = *(u8 *)(r7 +1)
11: (0f) r9 += r1
12: (07) r8 += 32
13: (2d) if r8 > r0 goto pc+1
R0=pkt_end R1=inv56 R6=ctx R7=pkt(id=0,off=0,r=32) R8=pkt(id=1,off=32,r=32) R9=pkt(id=1,off=0,r=32) R10=fp
14: (71) r1 = *(u8 *)(r9 +16)
15: (b7) r7 = 0
16: (bf) r0 = r7
17: (95) exit
We need to get a UNKNOWN_VALUE with imm to force id
generation so lines 0-5 make r7 a valid packet pointer.
We then read two different bytes from the packet and
add them to copies of the constructed packet pointer.
r8 (line 9) and r9 (line 11) will get the same id of 1,
independently. When either of them is validated (line
13) - find_good_pkt_pointers() will also mark the other
as safe. This leads to access on line 14 being mistakenly
considered safe.
Fixes: 969bf05eb3 ("bpf: direct packet access")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
For forwarding to be effective, XDP programs should be allowed to
rewrite packet data.
This requires that the drivers supporting XDP must all map the packet
memory as TODEVICE or BIDIRECTIONAL before invoking the program.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new bpf prog type that is intended to run in early stages of the
packet rx path. Only minimal packet metadata will be available, hence a
new context type, struct xdp_md, is exposed to userspace. So far only
expose the packet start and end pointers, and only in read mode.
An XDP program must return one of the well known enum values, all other
return codes are reserved for future use. Unfortunately, this
restriction is hard to enforce at verification time, so take the
approach of warning at runtime when such programs are encountered. Out
of bounds return codes should alias to XDP_ABORTED.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A subsystem may need to store many copies of a bpf program, each
deserving its own reference. Rather than requiring the caller to loop
one by one (with possible mid-loop failure), add a bulk bpf_prog_add
api.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should have been obvious, only called from bpf() syscall via map_update_elem()
that calls bpf_fd_array_map_update_elem() under RCU read lock and thus this
must also be in GFP_ATOMIC, of course.
Fixes: 3b1efb196e ("bpf, maps: flush own entries on perf map release")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work addresses a couple of issues bpf_skb_event_output()
helper currently has: i) We need two copies instead of just a
single one for the skb data when it should be part of a sample.
The data can be non-linear and thus needs to be extracted via
bpf_skb_load_bytes() helper first, and then copied once again
into the ring buffer slot. ii) Since bpf_skb_load_bytes()
currently needs to be used first, the helper needs to see a
constant size on the passed stack buffer to make sure BPF
verifier can do sanity checks on it during verification time.
Thus, just passing skb->len (or any other non-constant value)
wouldn't work, but changing bpf_skb_load_bytes() is also not
the proper solution, since the two copies are generally still
needed. iii) bpf_skb_load_bytes() is just for rather small
buffers like headers, since they need to sit on the limited
BPF stack anyway. Instead of working around in bpf_skb_load_bytes(),
this work improves the bpf_skb_event_output() helper to address
all 3 at once.
We can make use of the passed in skb context that we have in
the helper anyway, and use some of the reserved flag bits as
a length argument. The helper will use the new __output_custom()
facility from perf side with bpf_skb_copy() as callback helper
to walk and extract the data. It will pass the data for setup
to bpf_event_output(), which generates and pushes the raw record
with an additional frag part. The linear data used in the first
frag of the record serves as programmatically defined meta data
passed along with the appended sample.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig currently controlling compilation of this code is:
init/Kconfig:config BPF_SYSCALL
init/Kconfig: bool "Enable bpf() system call"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Note that MODULE_ALIAS is a no-op for non-modular code.
We replace module.h with init.h since the file does use __init.
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a bpf helper, bpf_skb_in_cgroup, to decide if a skb->sk
belongs to a descendant of a cgroup2. It is similar to the
feature added in netfilter:
commit c38c4597e4 ("netfilter: implement xt_cgroup cgroup2 path match")
The user is expected to populate a BPF_MAP_TYPE_CGROUP_ARRAY
which will be used by the bpf_skb_in_cgroup.
Modifications to the bpf verifier is to ensure BPF_MAP_TYPE_CGROUP_ARRAY
and bpf_skb_in_cgroup() are always used together.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a BPF_MAP_TYPE_CGROUP_ARRAY and its bpf_map_ops's implementations.
To update an element, the caller is expected to obtain a cgroup2 backed
fd by open(cgroup2_dir) and then update the array with that fd.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since bpf_prog_get() and program type check is used in a couple of places,
refactor this into a small helper function that we can make use of. Since
the non RO prog->aux part is not used in performance critical paths and a
program destruction via RCU is rather very unlikley when doing the put, we
shouldn't have an issue just doing the bpf_prog_get() + prog->type != type
check, but actually not taking the ref at all (due to being in fdget() /
fdput() section of the bpf fd) is even cleaner and makes the diff smaller
as well, so just go for that. Callsites are changed to make use of the new
helper where possible.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jann Horn reported following analysis that could potentially result
in a very hard to trigger (if not impossible) UAF race, to quote his
event timeline:
- Set up a process with threads T1, T2 and T3
- Let T1 set up a socket filter F1 that invokes another filter F2
through a BPF map [tail call]
- Let T1 trigger the socket filter via a unix domain socket write,
don't wait for completion
- Let T2 call PERF_EVENT_IOC_SET_BPF with F2, don't wait for completion
- Now T2 should be behind bpf_prog_get(), but before bpf_prog_put()
- Let T3 close the file descriptor for F2, dropping the reference
count of F2 to 2
- At this point, T1 should have looked up F2 from the map, but not
finished executing it
- Let T3 remove F2 from the BPF map, dropping the reference count of
F2 to 1
- Now T2 should call bpf_prog_put() (wrong BPF program type), dropping
the reference count of F2 to 0 and scheduling bpf_prog_free_deferred()
via schedule_work()
- At this point, the BPF program could be freed
- BPF execution is still running in a freed BPF program
While at PERF_EVENT_IOC_SET_BPF time it's only guaranteed that the perf
event fd we're doing the syscall on doesn't disappear from underneath us
for whole syscall time, it may not be the case for the bpf fd used as
an argument only after we did the put. It needs to be a valid fd pointing
to a BPF program at the time of the call to make the bpf_prog_get() and
while T2 gets preempted, F2 must have dropped reference to 1 on the other
CPU. The fput() from the close() in T3 should also add additionally delay
to the reference drop via exit_task_work() when bpf_prog_release() gets
called as well as scheduling bpf_prog_free_deferred().
That said, it makes nevertheless sense to move the BPF prog destruction
generally after RCU grace period to guarantee that such scenario above,
but also others as recently fixed in ceb5607035 ("bpf, perf: delay release
of BPF prog after grace period") with regards to tail calls won't happen.
Integrating bpf_prog_free_deferred() directly into the RCU callback is
not allowed since the invocation might happen from either softirq or
process context, so we're not permitted to block. Reviewing all bpf_prog_put()
invocations from eBPF side (note, cBPF -> eBPF progs don't use this for
their destruction) with call_rcu() look good to me.
Since we don't know whether at the time of attaching the program, we're
already part of a tail call map, we need to use RCU variant. However, due
to this, there won't be severely more stress on the RCU callback queue:
situations with above bpf_prog_get() and bpf_prog_put() combo in practice
normally won't lead to releases, but even if they would, enough effort/
cycles have to be put into loading a BPF program into the kernel already.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use smp_processor_id() for the generic helper bpf_get_smp_processor_id()
instead of the raw variant. This allows for preemption checks when we
have DEBUG_PREEMPT, and otherwise uses the raw variant anyway. We only
need to keep the raw variant for socket filters, but we can reuse the
helper that is already there from cBPF side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor cleanups: i) Remove the unlikely() from fd array map lookups
and let the CPU branch predictor do its job, scenarios where there is not
always a map entry are very well valid. ii) Move the attribute type check
in the bpf_perf_event_read() helper a bit earlier so it's consistent wrt
checks with bpf_perf_event_output() helper as well. iii) remove some
comments that are self-documenting in kprobe_prog_is_valid_access() and
therefore make it consistent to tp_prog_is_valid_access() as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
The behavior of perf event arrays are quite different from all
others as they are tightly coupled to perf event fds, f.e. shown
recently by commit e03e7ee34f ("perf/bpf: Convert perf_event_array
to use struct file") to make refcounting on perf event more robust.
A remaining issue that the current code still has is that since
additions to the perf event array take a reference on the struct
file via perf_event_get() and are only released via fput() (that
cleans up the perf event eventually via perf_event_release_kernel())
when the element is either manually removed from the map from user
space or automatically when the last reference on the perf event
map is dropped. However, this leads us to dangling struct file's
when the map gets pinned after the application owning the perf
event descriptor exits, and since the struct file reference will
in such case only be manually dropped or via pinned file removal,
it leads to the perf event living longer than necessary, consuming
needlessly resources for that time.
Relations between perf event fds and bpf perf event map fds can be
rather complex. F.e. maps can act as demuxers among different perf
event fds that can possibly be owned by different threads and based
on the index selection from the program, events get dispatched to
one of the per-cpu fd endpoints. One perf event fd (or, rather a
per-cpu set of them) can also live in multiple perf event maps at
the same time, listening for events. Also, another requirement is
that perf event fds can get closed from application side after they
have been attached to the perf event map, so that on exit perf event
map will take care of dropping their references eventually. Likewise,
when such maps are pinned, the intended behavior is that a user
application does bpf_obj_get(), puts its fds in there and on exit
when fd is released, they are dropped from the map again, so the map
acts rather as connector endpoint. This also makes perf event maps
inherently different from program arrays as described in more detail
in commit c9da161c65 ("bpf: fix clearing on persistent program
array maps").
To tackle this, map entries are marked by the map struct file that
added the element to the map. And when the last reference to that map
struct file is released from user space, then the tracked entries
are purged from the map. This is okay, because new map struct files
instances resp. frontends to the anon inode are provided via
bpf_map_new_fd() that is called when we invoke bpf_obj_get_user()
for retrieving a pinned map, but also when an initial instance is
created via map_create(). The rest is resolved by the vfs layer
automatically for us by keeping reference count on the map's struct
file. Any concurrent updates on the map slot are fine as well, it
just means that perf_event_fd_array_release() needs to delete less
of its own entires.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends map_fd_get_ptr() callback that is used by fd array
maps, so that struct file pointer from the related map can be passed
in. It's safe to remove map_update_elem() callback for the two maps since
this is only allowed from syscall side, but not from eBPF programs for these
two map types. Like in per-cpu map case, bpf_fd_array_map_update_elem()
needs to be called directly here due to the extra argument.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a release callback for maps that is invoked when the last
reference to its struct file is gone and the struct file about
to be released by vfs. The handler will be used by fd array maps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ctx structure passed into bpf programs is different depending on bpf
program type. The verifier incorrectly marked ctx->data and ctx->data_end
access based on ctx offset only. That caused loads in tracing programs
int bpf_prog(struct pt_regs *ctx) { .. ctx->ax .. }
to be incorrectly marked as PTR_TO_PACKET which later caused verifier
to reject the program that was actually valid in tracing context.
Fix this by doing program type specific matching of ctx offsets.
Fixes: 969bf05eb3 ("bpf: direct packet access")
Reported-by: Sasha Goldshtein <goldshtn@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix negative error code usage in ATM layer, from Stefan Hajnoczi.
2) If CONFIG_SYSCTL is disabled, the default TTL is not initialized
properly. From Ezequiel Garcia.
3) Missing spinlock init in mvneta driver, from Gregory CLEMENT.
4) Missing unlocks in hwmb error paths, also from Gregory CLEMENT.
5) Fix deadlock on team->lock when propagating features, from Ivan
Vecera.
6) Work around buffer offset hw bug in alx chips, from Feng Tang.
7) Fix double listing of SCTP entries in sctp_diag dumps, from Xin
Long.
8) Various statistics bug fixes in mlx4 from Eric Dumazet.
9) Fix some randconfig build errors wrt fou ipv6 from Arnd Bergmann.
10) All of l2tp was namespace aware, but the ipv6 support code was not
doing so. From Shmulik Ladkani.
11) Handle on-stack hrtimers properly in pktgen, from Guenter Roeck.
12) Propagate MAC changes properly through VLAN devices, from Mike
Manning.
13) Fix memory leak in bnx2x_init_one(), from Vitaly Kuznetsov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
sfc: Track RPS flow IDs per channel instead of per function
usbnet: smsc95xx: fix link detection for disabled autonegotiation
virtio_net: fix virtnet_open and virtnet_probe competing for try_fill_recv
bnx2x: avoid leaking memory on bnx2x_init_one() failures
fou: fix IPv6 Kconfig options
openvswitch: update checksum in {push,pop}_mpls
sctp: sctp_diag should dump sctp socket type
net: fec: update dirty_tx even if no skb
vlan: Propagate MAC address to VLANs
atm: iphase: off by one in rx_pkt()
atm: firestream: add more reserved strings
vxlan: Accept user specified MTU value when create new vxlan link
net: pktgen: Call destroy_hrtimer_on_stack()
timer: Export destroy_hrtimer_on_stack()
net: l2tp: Make l2tp_ip6 namespace aware
Documentation: ip-sysctl.txt: clarify secure_redirects
sfc: use flow dissector helpers for aRFS
ieee802154: fix logic error in ieee802154_llsec_parse_dev_addr
net: nps_enet: Disable interrupts before napi reschedule
net/lapb: tuse %*ph to dump buffers
...
Additionally to being able to control the system wide maximum depth via
/proc/sys/kernel/perf_event_max_stack, now we are able to ask for
different depths per event, using perf_event_attr.sample_max_stack for
that.
This uses an u16 hole at the end of perf_event_attr, that, when
perf_event_attr.sample_type has the PERF_SAMPLE_CALLCHAIN, if
sample_max_stack is zero, means use perf_event_max_stack, otherwise
it'll be bounds checked under callchain_mutex.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Zefan Li <lizefan@huawei.com>
Link: http://lkml.kernel.org/n/tip-kolmn1yo40p7jhswxwrc7rrd@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
