[ Upstream commit 9b71021b2e ]
All the sink pads of the crossbar switch require an active link if
they're part of the pipeline. Mark them with the
MEDIA_PAD_FL_MUST_CONNECT flag to fail pipeline validation if they're
not connected. This allows removing a manual check when translating
streams.
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb2f932100 ]
When translating source to sink streams in the crossbar subdev, the
driver tries to locate the remote subdev connected to the sink pad. The
remote pad may be NULL, if userspace tries to enable a stream that ends
at an unconnected crossbar sink. When that occurs, the driver
dereferences the NULL pad, leading to a crash.
Prevent the crash by checking if the pad is NULL before using it, and
return an error if it is.
Cc: stable@vger.kernel.org # 6.1
Fixes: cf21f328fc ("media: nxp: Add i.MX8 ISI driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20231201150614.63300-1-marex@denx.de
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfb1b99802 ]
The ipi handler here tries hard to maintain const-ness of its argument,
but by doing that causes a warning about function type casts:
drivers/media/platform/mediatek/vcodec/common/mtk_vcodec_fw_vpu.c:38:32: error: cast from 'mtk_vcodec_ipi_handler' (aka 'void (*)(void *, unsigned int, void *)') to 'ipi_handler_t' (aka 'void (*)(const void *, unsigned int, void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
38 | ipi_handler_t handler_const = (ipi_handler_t)handler;
| ^~~~~~~~~~~~~~~~~~~~~~
Remove the hack and just use a non-const argument.
Fixes: bf1d556ad4 ("media: mtk-vcodec: abstract firmware interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 856525e8db ]
While there is no good explanation what this value does, vendor driver
uses value 31 for it. Align driver with it.
Fixes: a4260ea495 ("media: sun4i: Add H3 deinterlace driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cff104e33b ]
According to user manual, reset line should be deasserted before clocks
are enabled. Also fix power down sequence to be reverse of that.
Fixes: a4260ea495 ("media: sun4i: Add H3 deinterlace driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 794b581f8c ]
Currently coefficients are applied only once, since they don't change.
However, this is done before enable bit is set and thus it doesn't get
applied properly.
Fix that by applying coefficients after enable bit is set. While this
means that it will be done evey time, it doesn't bring much time
penalty.
Fixes: a4260ea495 ("media: sun4i: Add H3 deinterlace driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 448699c522 ]
Since commit 1029939b37 ("media: v4l: async: Simplify async sub-device fwnode matching"),
async connections are matched using the async sub-device fwnode, not that
of the endpoint. Fix this by using the fwnode of the connection match to
find the pad.
Fixes: 1029939b37 ("media: v4l: async: Simplify async sub-device fwnode matching")
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffb635bb39 ]
The driver requests the interrupts as IRQF_SHARED, so the interrupt
handlers can be called at any time. If such a call happens while the ISP
is powered down, the SoC will hang as the driver tries to access the
ISP registers.
This can be reproduced even without the platform sharing the IRQ line:
Enable CONFIG_DEBUG_SHIRQ and unload the driver, and the board will
hang.
Fix this by adding a new field, 'irqs_enabled', which is used to bail
out from the interrupt handler when the ISP is not operational.
Link: https://lore.kernel.org/r/20231218-rkisp-shirq-fix-v1-2-173007628248@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a107d643b2 upstream.
This reverts commit 85d2a31fe4.
The rkisp1 does share interrupt lines on some platforms, after all. Thus
we need to revert this, and implement a fix for the rkisp1 shared irq
handling in a follow-up patch.
Closes: https://lore.kernel.org/all/87o7eo8vym.fsf@gmail.com/
Link: https://lore.kernel.org/r/20231218-rkisp-shirq-fix-v1-1-173007628248@ideasonboard.com
Reported-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9c8ddce2f ]
mutext_lock should not be called in condition of wait_event, otherwise,
when CONFIG_DEBUG_ATOMIC_SLEEP is enabled, we may meet the following
warning:
do not call blocking ops when !TASK_RUNNING; state=2
WARNING: CPU: 5 PID: 741 at kernel/sched/core.c:9859
__might_sleep+0x80/0xa4
Hardware name: Freescale i.MX8QM MEK (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc :
__might_sleep+0x80/0xa4 lr : __might_sleep+0x80/0xa4 sp : ffffffc0123738a0
x29: ffffffc0123738a0 x28: ffffffc009194c48 x27: ffffffc00bbc1050
x26: ffffff8814b282f0 x25: ffffff8814b280d0 x24: ffffff8814b28080
x23: 0000000000000001 x22: 0000000000000032 x21: ffffffc00bbc1000
x20: 000000000000011b x19: ffffffc009324670 x18: 00000000fffffffd
x17: 30303c5b20746120 x16: 74657320323d6574 x15: 617473203b474e49
x14: 00058b5b8b9aa1f1 x13: ffffffc00903cda0 x12: 00000000d744fcc9
x11: 000000000000001c x10: 00000000000009a0 x9 : ffffffc0090201f4
x8 : ffffff8828245000 x7 : 0000000000000001 x6 : 0000000000000001
x5 : 00000000410fd080 x4 : 0000000000000002 x3 : ffffff8815aab4c8
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffffff8828244600
Call trace:
__might_sleep+0x80/0xa4
mutex_lock+0x2c/0x80
sync_session_response+0x110/0x310
vpu_session_send_cmd+0x18c/0x244
vpu_session_start+0x38/0x70
vdec_start_session+0x1b4/0x3e0
vpu_vb2_start_streaming+0xa0/0x1c4
vb2_start_streaming+0x74/0x160
vb2_core_qbuf+0x488/0x650
vb2_qbuf+0x9c/0x100
v4l2_m2m_qbuf+0x7c/0x224
v4l2_m2m_ioctl_qbuf+0x20/0x2c
v4l_qbuf+0x50/0x6c
__video_do_ioctl+0x174/0x3f0
video_usercopy+0x210/0x7cc
video_ioctl2+0x20/0x30
v4l2_ioctl+0x48/0x6c
we need to refine check_is_responsed() to remove the mutext_lock, each
cmd has a monotonically increasing id, and cmds are executed
sequentially, so we can check the id of the last reponsed cmd, then
determine whether a command has been responded or not.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
CC: Xiaolei Wang <xiaolei.wang@windriver.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efa28efd9c ]
Supported media bus codes on the resizer sink pad are identical to the
ISP source pad. The .enum_mbus_code() handler thus delegates the
enumeration to the ISP's operation. This is problematic for two
reasons:
- Format enumeration on the ISP source pad is dependent on the format
configured on the ISP sink pad for the same subdev state (TRY or
ACTIVE), while format enumeration on the resizer sink pad should
return all formats supported by the resizer subdev, regardless of the
ISP configuration.
- Delegating the operation involves creating a fake v4l2_subdev_state on
the stack to pass to the ISP .enum_mbus_code() handler. This gets in
the way of evolution of both the ISP enumeration handler and, more
generally, the V4L2 subdev state infrastructure.
Fix those two issues by implementing format enumeration manually for the
resizer.
Link: https://lore.kernel.org/r/20231126020948.2700-1-laurent.pinchart@ideasonboard.com
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 870565f063 ]
In rkisp1_isp_stop() and rkisp1_csi_disable() the driver masks the
interrupts and then apparently assumes that the interrupt handler won't
be running, and proceeds in the stop procedure. This is not the case, as
the interrupt handler can already be running, which would lead to the
ISP being disabled while the interrupt handler handling a captured
frame.
This brings up two issues: 1) the ISP could be powered off while the
interrupt handler is still running and accessing registers, leading to
board lockup, and 2) the interrupt handler code and the code that
disables the streaming might do things that conflict.
It is not clear to me if 2) causes a real issue, but 1) can be seen with
a suitable delay (or printk in my case) in the interrupt handler,
leading to board lockup.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-4-358a2c871a3c@ideasonboard.com
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0753874617 ]
Store the IRQ lines used by the driver for easy access. These are needed
in future patches which fix IRQ race issues.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-3-358a2c871a3c@ideasonboard.com
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3eb7910e1b ]
The IRQ handler rkisp1_isr() calls sub-handlers, all of which returns an
irqreturn_t value, but rkisp1_isr() ignores those values and always
returns IRQ_HANDLED.
Fix this by collecting the return values, and returning IRQ_HANDLED or
IRQ_NONE as appropriate.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-2-358a2c871a3c@ideasonboard.com
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85d2a31fe4 ]
In all known platforms the ISP has dedicated IRQ lines, but for some
reason the driver uses IRQF_SHARED.
Supporting IRQF_SHARED properly requires handling interrupts even when
our device is disabled, and the driver does not handle this. To avoid
adding such code, and to be sure the driver won't accidentally be used
in a platform with shared interrupts, let's drop the IRQF_SHARED flag.
Link: https://lore.kernel.org/r/20231207-rkisp-irq-fix-v3-1-358a2c871a3c@ideasonboard.com
Tested-by: Adam Ford <aford173@gmail.com> #imx8mp-beacon
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e7dc39260 ]
When using 32 bit RGB formats, the RGA on the rk3568 produces wrong
colors as the wrong color channels are read or written. The reason is
that the format description for the channel swizzeling is wrong and the
wrong bits are configured. For example, when converting ARGB32 to NV12,
the alpha channel is used as blue channel.. This doesn't happen if the
color format is the same on both sides.
Fix the color_swap settings of the formats to correctly handle 32 bit
RGB formats.
For RGA_COLOR_FMT_XBGR8888, the RGA_COLOR_ALPHA_SWAP bit doesn't have an
effect. Thus, it isn't possible to handle the V4L2_PIX_FMT_XRGB32. Thus,
it is removed from the list of supported formats.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 206c857dd1 upstream.
In mtk_jpeg_probe, &jpeg->job_timeout_work is bound with
mtk_jpeg_job_timeout_work.
In mtk_jpeg_dec_device_run, if error happens in
mtk_jpeg_set_dec_dst, it will finally start the worker while
mark the job as finished by invoking v4l2_m2m_job_finish.
There are two methods to trigger the bug. If we remove the
module, it which will call mtk_jpeg_remove to make cleanup.
The possible sequence is as follows, which will cause a
use-after-free bug.
CPU0 CPU1
mtk_jpeg_dec_... |
start worker |
|mtk_jpeg_job_timeout_work
mtk_jpeg_remove |
v4l2_m2m_release |
kfree(m2m_dev); |
|
| v4l2_m2m_get_curr_priv
| m2m_dev->curr_ctx //use
If we close the file descriptor, which will call mtk_jpeg_release,
it will have a similar sequence.
Fix this bug by starting timeout worker only if started jpegdec worker
successfully. Then v4l2_m2m_job_finish will only be called in
either mtk_jpeg_job_timeout_work or mtk_jpeg_dec_device_run.
Fixes: b2f0d2724b ("[media] vcodec: mediatek: Add Mediatek JPEG Decoder Driver")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 38e1857933 upstream.
In mtk_jpegdec_worker, if error occurs in mtk_jpeg_set_dec_dst, it
will start the timeout worker and invoke v4l2_m2m_job_finish at
the same time. This will break the logic of design for there should
be only one function to call v4l2_m2m_job_finish. But now the timeout
handler and mtk_jpegdec_worker will both invoke it.
Fix it by start the worker only if mtk_jpeg_set_dec_dst successfully
finished.
Fixes: da4ede4b7f ("media: mtk-jpeg: move data/code inside CONFIG_OF blocks")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb387fcb5c ]
The driver always enables the clocks at probe() and disables them only
at remove(). It is not clear why the driver does this, as it supports
runtime PM, and enables and disables the clocks in the runtime resume
and suspend callbacks. Also, in the case runtime PM is not available,
the driver calls the resume and suspend callbacks manually from probe()
and remove().
Drop the unnecessary clock enable, thus enabling the clocks only when
actually needed.
Link: https://lore.kernel.org/r/20231122-imx-csis-v2-2-e44b8dc4cb66@ideasonboard.com
Fixes: 7807063b86 ("media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5705b0e0eb ]
The driver always calls mipi_csis_runtime_suspend() and
mipi_csis_clk_disable() in remove(). This causes multiple WARNs from the
kernel, as the clocks get disabled too many times.
Fix the remove() to call mipi_csis_runtime_suspend() and
mipi_csis_clk_disable() in a way that reverses what is done in probe().
Link: https://lore.kernel.org/r/20231122-imx-csis-v2-1-e44b8dc4cb66@ideasonboard.com
Fixes: 7807063b86 ("media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f033c87fda ]
Starting with commit f6038de293 ("arm64: dts: imx8qm: Fix VPU core
alias name") the alias for VPU cores uses dashes instead of underscores.
Adjust the alias stem accordingly. Fixes the errors:
amphion-vpu-core 2d040000.vpu-core: can't get vpu core id
amphion-vpu-core 2d050000.vpu-core: can't get vpu core id
Fixes: f6038de293 ("arm64: dts: imx8qm: Fix VPU core alias name")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c0d9e12b1 ]
The (TRY_)DECODER_CMD ioctls are used to support flushing when holding
capture buffers is supported. This is the case of this driver but the
ioctls were never hooked to the ioctl ops.
Add them to correctly support flushing.
Fixes: 340ce50f75 ("media: hantro: Enable HOLD_CAPTURE_BUF for H.264")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8212c5c87 ]
This patch reverts commit c677d7ae83
("media: mtk-jpeg: Fix use after free bug due to uncanceled work").
The job_timeout_work is initialized only for
the single-core JPEG device so it will cause the crash for multi-core
JPEG devices.
Fix it by removing the cancel_delayed_work_sync function.
Fixes: c677d7ae83 ("media: mtk-jpeg: Fix use after free bug due to uncanceled work")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f910d3ba78 upstream.
Digging into the documentation we find that the DT_ID bitfield is used to
map the six bit DT to a two bit ID code. This value is concatenated to the
VC bitfield to create a CID value. DT_ID is the two least significant bits
of CID and VC the most significant bits.
Originally we set dt_id = vc * 4 in and then subsequently set dt_id = vc.
commit 3c4ed72a16 ("media: camss: sm8250: Virtual channels for CSID")
silently fixed the multiplication by four which would give a better
value for the generated CID without mentioning what was being done or why.
Next up I haplessly changed the value back to "dt_id = vc * 4" since there
didn't appear to be any logic behind it.
Hans asked what the change was for and I honestly couldn't remember the
provenance of it, so I dug in.
Link: https://lore.kernel.org/linux-arm-msm/edd4bf9b-0e1b-883c-1a4d-50f4102c3924@xs4all.nl/
Add a comment so the next hapless programmer doesn't make this same
mistake.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f69791c397 ]
Right now we never release the power-domains properly on the error path.
Add a routine to be reused for this purpose and appropriate jumps in
probe() to run that routine where necessary.
Fixes: 2f6f8af672 ("media: camss: Refactor VFE power domain toggling")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b278080a89 ]
Previously the jump label err_cleanup was used higher in the probe()
function to release the async notifier however the async notifier
registration was moved later in the code rendering the previous four jumps
redundant.
Rename the label from err_cleanup to err_v4l2_device_unregister to capture
what the jump does.
Fixes: 51397a4ec75d ("media: qcom: Initialise V4L2 async notifier later")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: fix old name in commit log: err_v4l2_device_register -> err_v4l2_device_unregister]
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 87889f1b7e upstream.
In the current driver csid Test Pattern Generator (TPG) doesn't work.
This change:
- fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
- fixes the shift by one between test_pattern control value and the
actual pattern.
- drops fixed VC of 0x0a which testing showed prohibited some test
patterns in the CSID to produce output.
So that TPG starts working, but with the below limitations:
- only test_pattern=9 works as it should
- test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
- the rest of test_pattern's don't work (yavta doesn't get the data)
- regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
order is always the same (RGGB for any RAW8 or RAW10P format in
4608x2592 resolution).
Tested with:
RAW10P format, VC0:
media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video0
RAW10P format, VC1:
media-ctl -V '"msm_csid0":2[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video1
RAW8 format, VC0:
media-ctl --reset
media-ctl -V '"msm_csid0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB8 -s 4608x2592 /dev/video0
Fixes: eebe6d00e9 ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8f7e1a60d upstream.
define CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE BIT(7)
disjunction for gen2 ? BIT(7) : is a nop we are setting the same bit
either way.
Fixes: 4abb21309f ("media: camss: csiphy: Move to hardcode CSI Clock Lane number")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e655d1ae97 upstream.
VC_MODE = 0 implies a two bit VC address.
VC_MODE = 1 is required for VCs with a larger address than two bits.
Fixes: eebe6d00e9 ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6e1bdca46 upstream.
check_clock doesn't account for vfe_lite which means that vfe_lite will
never get validated by this routine. Add the clock name to the expected set
to remediate.
Fixes: 7319cdf189 ("media: camss: Add support for VFE hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f24d29135 upstream.
vfe-480 is copied from vfe-17x and has the same racy idle timeout bug as in
17x.
Fix the vfe_disable_output() logic to no longer be racy and to conform
to the 17x way of quiescing and then resetting the VFE.
Fixes: 4edc8eae71 ("media: camss: Add initial support for VFE hardware version Titan 480")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3143ad282f upstream.
There are two problems with the current vfe_disable_output() routine.
Firstly we rightly use a spinlock to protect output->gen2.active_num
everywhere except for in the IDLE timeout path of vfe_disable_output().
Even if that is not racy "in practice" somehow it is by happenstance not
by design.
Secondly we do not get consistent behaviour from this routine. On
sc8280xp 50% of the time I get "VFE idle timeout - resetting". In this
case the subsequent capture will succeed. The other 50% of the time, we
don't hit the idle timeout, never do the VFE reset and subsequent
captures stall indefinitely.
Rewrite the vfe_disable_output() routine to
- Quiesce write masters with vfe_wm_stop()
- Set active_num = 0
remembering to hold the spinlock when we do so followed by
- Reset the VFE
Testing on sc8280xp and sdm845 shows this to be a valid fix.
Fixes: 7319cdf189 ("media: camss: Add support for VFE hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7405116519 upstream.
We need to make sure camss_configure_pd() happens before
camss_register_entities() as the vfe_get() path relies on the pointer
provided by camss_configure_pd().
Fix the ordering sequence in probe to ensure the pointers vfe_get() demands
are present by the time camss_register_entities() runs.
In order to facilitate backporting to stable kernels I've moved the
configure_pd() call pretty early on the probe() function so that
irrespective of the existence of the old error handling jump labels this
patch should still apply to -next circa Aug 2023 to v5.13 inclusive.
Fixes: 2f6f8af672 ("media: camss: Refactor VFE power domain toggling")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8d0b89398b upstream.
The hfi parser, parses the capabilities received from venus firmware and
copies them to core capabilities. Consider below api, for example,
fill_caps - In this api, caps in core structure gets updated with the
number of capabilities received in firmware data payload. If the same api
is called multiple times, there is a possibility of copying beyond the max
allocated size in core caps.
Similar possibilities in fill_raw_fmts and fill_profile_level functions.
Cc: stable@vger.kernel.org
Fixes: 1a73374a04 ("media: venus: hfi_parser: add common capability parser")
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b18e36dfd6 upstream.
Buffer requirement, for different buffer type, comes from video firmware.
While copying these requirements, there is an OOB possibility when the
payload from firmware is more than expected size. Fix the check to avoid
the OOB possibility.
Cc: stable@vger.kernel.org
Fixes: 09c2845e8f ("[media] media: venus: hfi: add Host Firmware Interface (HFI)")
Reviewed-by: Nathan Hebert <nhebert@chromium.org>
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0768a9dd80 upstream.
Supported codec bitmask is populated from the payload from venus firmware.
There is a possible case when all the bits in the codec bitmask is set. In
such case, core cap for decoder is filled and MAX_CODEC_NUM is utilized.
Now while filling the caps for encoder, it can lead to access the caps
array beyong 32 index. Hence leading to OOB write.
The fix counts the supported encoder and decoder. If the count is more than
max, then it skips accessing the caps.
Cc: stable@vger.kernel.org
Fixes: 1a73374a04 ("media: venus: hfi_parser: add common capability parser")
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e538fce33 upstream.
Read and write pointers are used to track the packet index in the memory
shared between video driver and firmware. There is a possibility of OOB
access if the read or write pointer goes beyond the queue memory size.
Add checks for the read and write pointer to avoid OOB access.
Cc: stable@vger.kernel.org
Fixes: d96d3f30c0 ("[media] media: venus: hfi: add Venus HFI files")
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a76e7679b ]
Fix the build warnings that were detected by the linux-media
build scripts tool:
drivers/media/platform/mediatek/mdp3/mtk-mdp3-cmdq.c:
In function 'mdp_path_config.isra':
drivers/media/platform/mediatek/mdp3/mtk-mdp3-cmdq.c:
warning: 'ctx' may be used uninitialized [-Wmaybe-uninitialized]
| out = CFG_COMP(MT8195, ctx->param, outputs[0]);
| ~~~^~~~~~~
drivers/media/platform/mediatek/mdp3/mtk-img-ipi.h: note:
in definition of macro 'CFG_COMP'
| (IS_ERR_OR_NULL(comp) ? 0 : _CFG_COMP(plat, comp, mem))
| ^~~~
drivers/media/platform/mediatek/mdp3/mtk-mdp3-cmdq.c:
note: 'ctx' was declared here
| struct mdp_comp_ctx *ctx;
|
Fixes: 61890ccaef ("media: platform: mtk-mdp3: add MediaTek MDP3 driver")
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b833b17849 ]
After gstreamer rework the dynamic resolution change handling, gstreamer
stop doing capture buffer allocation based on guesses and wait for the
source change event when available. It requires driver always notify
source change event in the initialization, even if the size parsed is
equal to the size set on capture queue. otherwise, the pipeline will be
stalled.
Currently driver may not notify source change event if the parsed format
and size are equal to those previously established, but it may stall the
gstreamer pipeline.
The link of gstreamer patch is
https://gitlab.freedesktop.org/gstreamer/gstreamer/-/merge_requests/4437
Fixes: b4e1fb8643 ("media: imx-jpeg: Support dynamic resolution change")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19e2e01f30 ]
Handle invalid encoder vsi in vpu_enc_init to ensure the encoder
vsi is valid for future use.
Fixes: 1972e32431 ("media: mediatek: vcodec: Fix possible invalid memory access for encoder")
Signed-off-by: Irui Wang <irui.wang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39377f84fb ]
Mainlined RK3588 clock driver manage by itself the dependency between
aclk/hclk and their root clocks (aclk_vdpu_root/hclk_vdpu_root).
RK3588 av1 video decoder do not have to take care of it anymore so
remove them from the list and be compliant with yaml bindings description.
Fixes: 003afda97c ("media: verisilicon: Enable AV1 decoder on rk3588")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b270171530 ]
The notifier is added to the global notifier list when registered. When
the module is removed, the struct csi2rx_priv in which the notifier is
embedded, is destroyed. As a result the notifier list has a reference to
a notifier that no longer exists. This causes invalid memory accesses
when the list is iterated over. Similar for when the probe fails.
Unregister and clean up the notifier to avoid this.
Fixes: 1fc3b37f34 ("media: v4l: cadence: Add Cadence MIPI-CSI2 RX driver")
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61334819ac ]
s3c_camif_register_video_node() works with video_device structure stored
as a field of camif_vp, so it should not be kfreed.
But there is video_device_release() on error path that do it.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: babde1c243 ("[media] V4L: Add driver for S3C24XX/S3C64XX SoC series camera interface")
Signed-off-by: Katya Orlova <e.orlova@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0aeccc63f3 ]
The driver uses the upper-bound approach to decide the target JPEG
encode quality, but there's a logic bug that if the desired quality is
higher than what the driver can support, the driver falls back to using
the worst quality.
Fix the bug by assuming using the best quality in the beginning, and
with trivial refactor to avoid long lines.
Fixes: 45f13a57d8 ("media: platform: Add jpeg enc feature")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6496617b2b ]
decoder firmware may notify host some debug message,
it can help analyze the state of the firmware in case of error
Fixes: 9f599f351e ("media: amphion: add vpu core driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e481d52d3 ]
In case of encoded input VP9 data width that is not multiple of macroblock
size, which is 16 (e.g. 1080x1920 frames, where 1080 is multiple of 8), the
width is padded to be a multiple of macroblock size (for 1080x1920 frames,
that is 1088x1920).
The hantro_postproc_g2_enable() checks whether the encoded data width is
equal to decoded frame width, and if not, enables down-scale mode. For a
frame where input is 1080x1920 and output is 1088x1920, this is incorrect
as no down-scale happens, the frame is only padded. Enabling the down-scale
mode in this case results in corrupted frames.
Fix this by adjusting the check to test whether encoded data width is
greater than decoded frame width, and only in that case enable the
down-scale mode.
To generate input test data to trigger this bug, use e.g.:
$ gst-launch-1.0 videotestsrc ! video/x-raw,width=272,height=256,format=I420 ! \
vp9enc ! matroskamux ! filesink location=/tmp/test.vp9
To trigger the bug upon decoding (note that the NV12 must be forced, as
that assures the output data would pass the G2 postproc):
$ gst-launch-1.0 filesrc location=/tmp/test.vp9 ! matroskademux ! vp9parse ! \
v4l2slvp9dec ! video/x-raw,format=NV12 ! videoconvert ! fbdevsink
Fixes: 79c987de8b ("media: hantro: Use post processor scaling capacities")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88d4b23a62 ]
The i.MX8MM/N/P does not define the .reset op since reset of the VPU is
done by genpd. Check whether the .reset op is defined before calling it
to avoid NULL pointer dereference.
Note that the Fixes tag is set to the commit which removed the reset op
from i.MX8M Hantro G2 implementation, this is because before this commit
all the implementations did define the .reset op.
Fixes: 6971efb70a ("media: hantro: Allow i.MX8MQ G1 and G2 to run independently")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
