Commit graph

15 commits

Author SHA1 Message Date
Rafael J. Wysocki
2b844ba79f Revert "ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs"
This reverts commit f6308b36c4 (ACPI: Add BayTrail SoC GPIO and LPSS
ACPI IDs), because it causes the Alan Cox' ASUS T100TA to "crash and
burn" during boot if the Baytrail pinctrl driver is compiled in.

Fixes: f6308b36c4 (ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs)
Reported-by: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Requested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-01-18 14:04:58 +01:00
Paul Drews
f6308b36c4 ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
This adds the new ACPI ID (INT33FC) for the BayTrail GPIO
banks as seen on a BayTrail M System-On-Chip platform.  This
ACPI ID is used by the BayTrail GPIO (pinctrl) driver to
manage the Low Power Subsystem (LPSS).

Signed-off-by: Paul Drews <paul.drews@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-11-30 15:07:36 +01:00
Rafael J. Wysocki
f86e7bc968 Merge branch 'acpi-lpss'
* acpi-lpss:
  ACPI / LPSS: add ACPI IDs for newer Intel PCHs
2013-11-16 15:45:13 +01:00
Mika Westerberg
a4d97536a1 ACPI / LPSS: add ACPI IDs for newer Intel PCHs
Some recent Intel PCHs with LPSS have different ACPI IDs for the LPSS
devices, so add these to the list as well.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-11-12 22:52:00 +01:00
Heikki Krogerus
088f1fd267 ACPI / LPSS: fix UART Auto Flow Control
There is an additional bit in the GENERAL register on newer
silicon that needs to be set or UART's RTS pin fails to
reflect the flow control settings in the Modem Control
Register.

This will fix an issue where the RTS pin of the UART stays
always at 1.8V, regardless of the register settings.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-10-10 22:31:21 +02:00
Mika Westerberg
af65cfe9ae ACPI / LPSS: don't crash if a device has no MMIO resources
Intel LPSS devices that are enumerated from ACPI have both MMIO and IRQ
resources returned in their _CRS method. However, Apple Macbook Air with
Haswell has LPSS devices enumerated from PCI bus instead and _CRS method
returns only an interrupt number (but the device has _HID set that causes
the scan handler to match it).

The current ACPI / LPSS code sets pdata->dev_desc only when MMIO resource
is found for the device and in case of Macbook Air it is never found. That
leads to a NULL pointer dereference in register_device_clock().

Correct this by always setting the pdata->dev_desc.

Reported-and-tested-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-09-02 12:59:40 +02:00
Rafael J. Wysocki
f4c9f40238 Merge branch 'acpi-lpss'
* acpi-lpss:
  ACPI / LPSS: override SDIO private register space size from ACPI tables
  ACPI / LPSS: mask the UART TX completion interrupt
  ACPI / LPSS: add support for Intel BayTrail

Conflicts:
	drivers/acpi/acpi_lpss.c (with commit b9e95fc)
2013-06-28 12:59:02 +02:00
Rafael J. Wysocki
b9e95fc65e ACPI / LPSS: Power up LPSS devices during enumeration
Commit 7cd8407 (ACPI / PM: Do not execute _PS0 for devices without
_PSC during initialization) introduced a regression on some systems
with Intel Lynxpoint Low-Power Subsystem (LPSS) where some devices
need to be powered up during initialization, but their device objects
in the ACPI namespace have _PS0 and _PS3 only (without _PSC or power
resources).

To work around this problem, make the ACPI LPSS driver power up
devices it knows about by using a new helper function
acpi_device_fix_up_power() that does all of the necessary
sanity checks and calls acpi_dev_pm_explicit_set() to put the
device into D0.

Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-06-20 00:49:06 +02:00
Mika Westerberg
958c4eb2aa ACPI / LPSS: override SDIO private register space size from ACPI tables
The SDIO device in Lynxpoint has its LTR registers reserved for a
WiFi device (a child of the SDIO device) in the ACPI namespace even
though those registers physically belong to the SDIO device itself.
In order to be able to access the SDIO LTR registers from the ACPI
LPSS driver for diagnostic purposes we need to use a size override
for the SDIO private register space.

Add a possibility to override the size of the private register space
of an LPSS device provided by the ACPI tables in the ACPI LPSS driver
and set the correct size for the SDIO device in there.

[rjw: Changelog]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-06-19 01:33:37 +02:00
Heikki Krogerus
06d8641504 ACPI / LPSS: mask the UART TX completion interrupt
Intel LPSS provides an extra TX byte counter and an extra TX
completion interrupt for some of its bus controllers.  However,
there is no use for the extra UART interrupt and it has to be
masked out during initialization.

Otherwise, if the firmware does not mask the interrupt and
the driver does not clear it, it may cause an interrupt flood
freezing the board to happen.

Add code masking that problematic interrupt to the ACPI LPSS driver.

[rjw: Changelog]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-06-19 01:31:26 +02:00
Mika Westerberg
f627217064 ACPI / LPSS: add support for Intel BayTrail
Intel BayTrail has almost the same Low Power Subsystem than Lynxpoint with
few differences. Peripherals are clocked with different speeds (typically
lower) and the clock is not always gated. To support this we add
possibility to share a common fixed rate clock and make clock gating
optional.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-06-19 01:08:47 +02:00
Rafael J. Wysocki
b59cc200ac ACPI / LPSS: register clock device for Lynxpoint DMA properly
The DMA controller in Lynxpoint is enumerated as a regular ACPI device now. To
work properly it is using the LPSS root clock as a functional clock. That's why
we have to register the clock device accordingly to the ACPI ID of the DMA
controller. The acpi_lpss.c module is responsible to do the job.

This patch also removes hardcoded name of the DMA device in clk-lpt.c and the
name of the root clock in acpi_lpss.c.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2013-05-14 10:23:58 +05:30
Andy Shevchenko
cf8df962aa ACPI / LPSS: make code less confusing for reader
The excerpt like this:

	if (err) {
		err = 0;
		goto error_out;
	}

makes a reader confused even if it's commented. Let's do necessary actions and
return no error explicitly.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-03-25 00:21:49 +01:00
Rafael J. Wysocki
2e0f8822d1 ACPI / LPSS: Add support for exposing LTR registers to user space
Devices on the Intel Lynxpoint Low Power Subsystem (LPSS) have
registers providing access to LTR (Latency Tolerance Reporting)
functionality that allows software to monitor and possibly influence
the aggressiveness of the platform's active-state power management.

For each LPSS device, there are two modes of operation related to LTR,
the auto mode and the software mode.  In the auto mode the LTR is
set up by the platform firmware and managed by hardware.  Software
can only read the LTR register values to monitor the platform's
behavior.  In the software mode it is possible to use LTR to control
the extent to which the platform will use its built-in power
management features.

This changeset adds support for reading the LPSS devices' LTR
registers and exposing their values to user space for monitoring and
diagnostics purposes.  It re-uses the MMIO mappings created to access
the LPSS devices' clock registers for reading the values of the LTR
registers and exposes them to user space through sysfs device
attributes.  Namely, a new atrribute group, lpss_ltr, is created for
each LPSS device.  It contains three new attributes: ltr_mode,
auto_ltr, sw_ltr.  The value of the ltr_mode attribute reflects the
LTR mode being used at the moment (software vs auto) and the other
two contain the actual register values (raw) whose meaning depends
on the LTR mode.  All of these attributes are read-only.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-03-21 22:45:15 +01:00
Rafael J. Wysocki
f58b082aed ACPI / scan: Add special handler for Intel Lynxpoint LPSS devices
Devices on the Intel Lynxpoint Low Power Subsystem (LPSS) have some
common features that aren't shared with any other platform devices,
including the clock and LTR (Latency Tolerance Reporting) registers.
It is better to handle those features in common code than to bother
device drivers with doing that (I/O functionality-wise the LPSS
devices are generally compatible with other devices that don't
have those special registers and may be handled by the same drivers).

The clock registers of the LPSS devices are now taken care of by
the special clk-x86-lpss driver, but the MMIO mappings used for
accessing those registers can also be used for accessing the LTR
registers on those devices (LTR support for the Lynxpoint LPSS is
going to be added by a subsequent patch).  Thus it is convenient
to add a special ACPI scan handler for the Lynxpoint LPSS devices
that will create the MMIO mappings for accessing the clock (and
LTR in the future) registers and will register the LPSS devices'
clocks, so the clk-x86-lpss driver will only need to take care of
the main Lynxpoint LPSS clock.

Introduce a special ACPI scan handler for Intel Lynxpoint LPSS
devices as described above.  This also reduces overhead related to
browsing the ACPI namespace in search of the LPSS devices before the
registration of their clocks, removes some LPSS-specific (and
somewhat ugly) code from acpi_platform.c and shrinks the overall code
size slightly.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
2013-03-21 22:44:38 +01:00