cpufreq_rwsem was introduced in commit 6eed9404ab ("cpufreq: Use
rwsem for protecting critical sections) in order to replace
try_module_get() on the cpu-freq driver. That try_module_get() worked
well until the refcount was so heavily used that module removal became
more or less impossible.
Though when looking at the various (undocumented) protection
mechanisms in that code, the randomly sprinkeled around cpufreq_rwsem
locking sites are superfluous.
The policy, which is acquired in cpufreq_cpu_get() and released in
cpufreq_cpu_put() is sufficiently protected already.
cpufreq_cpu_get(cpu)
/* Protects against concurrent driver removal */
read_lock_irqsave(&cpufreq_driver_lock, flags);
policy = per_cpu(cpufreq_cpu_data, cpu);
kobject_get(&policy->kobj);
read_unlock_irqrestore(&cpufreq_driver_lock, flags);
The reference on the policy serializes versus module unload already:
cpufreq_unregister_driver()
subsys_interface_unregister()
__cpufreq_remove_dev_finish()
per_cpu(cpufreq_cpu_data) = NULL;
cpufreq_policy_put_kobj()
If there is a reference held on the policy, i.e. obtained prior to the
unregister call, then cpufreq_policy_put_kobj() will wait until that
reference is dropped. So once subsys_interface_unregister() returns
there is no policy pointer in flight and no new reference can be
obtained. So that rwsem protection is useless.
The other usage of cpufreq_rwsem in show()/store() of the sysfs
interface is redundant as well because sysfs already does the proper
kobject_get()/put() pairs.
That leaves CPU hotplug versus module removal. The current
down_write() around the write_lock() in cpufreq_unregister_driver() is
silly at best as it protects actually nothing.
The trivial solution to this is to prevent hotplug across
cpufreq_unregister_driver completely.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Return codes aren't honored properly in cpufreq_set_policy(). This can
lead to two problems:
- wrong errors propagated to sysfs
- we try to do next state-change even if the previous one failed
cpufreq_governor_dbs() now returns proper errors on all invalid
state-transition requests and this code should honor that.
Reviewed-and-tested-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_init_policy() can fail, and we don't do anything except a call
to ->exit() on that. The policy should be freed if this happens.
Do it properly.
Reported-and-tested-by: "Jon Medhurst (Tixy)" <tixy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These labels are are named in two ways normally:
- Based on what caused to jump to such labels
- Based on what we do under such labels
We follow the first naming convention today and that leads to multiple
labels for doing the same work. Fix it by switching to the second way of
naming them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Users of freq table may want to access it for any CPU from
policy->related_cpus mask. One such user is cpu-cooling layer. It gets a
list of 'clip_cpus' (equivalent to policy->related_cpus) during
registration and tries to get freq_table for the first CPU of this mask.
If the CPU, for which it tries to fetch freq_table, is offline,
cpufreq_frequency_get_table() fails. This happens because it relies on
cpufreq_cpu_get_raw() for its functioning which returns policy only for
online CPUs.
The fix is to access the policy data structure for the given CPU
directly (which also returns a valid policy for offline CPUs), but the
policy itself has to be active (meaning that at least one CPU using it
is online) for the frequency table to be returned.
Because we will be using 'cpufreq_cpu_data' now, which is internal to
the cpufreq core, move cpufreq_frequency_get_table() to cpufreq.c.
Reported-and-tested-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When all CPUs of a policy are hot-unplugged, we EXIT the governor but
don't mark policy->governor as NULL. This was done in order to keep last
used governor's information intact in sysfs, while the CPUs are offline.
But we also need to clear policy->governor when restoring the policy.
Because policy->governor still points to the last governor while policy
is restored, following sequence of event happens:
- cpufreq_init_policy() called while restoring policy
- find_governor() matches last_governor string for present governors and
returns last used governor's pointer, say ondemand. policy->governor
already has the same address, unless the governor was removed in
between.
- cpufreq_set_policy() is called with both old/new policies governor set
as ondemand.
- Because governors matched, we skip governor initialization and return
after calling __cpufreq_governor(CPUFREQ_GOV_LIMITS). Because the
governor wasn't initialized for this policy, it returned -EBUSY.
- cpufreq_init_policy() exits the policy on this error, but doesn't
destroy it properly (should be fixed separately).
- And so we enter a scenario where the policy isn't completely
initialized but used.
Fix this by setting policy->governor to NULL while restoring the policy.
Reported-and-tested-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>
Reported-and-tested-by: "Jon Medhurst (Tixy)" <tixy@linaro.org>
Reported-and-tested-by: Steven Rostedt <rostedt@goodmis.org>
Fixes: 18bf3a124e (cpufreq: Mark policy->governor = NULL for inactive policies)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_update_policy() was kept as a separate routine earlier as it was
handling migration of sysfs directories, which isn't the case anymore.
It is only updating policy->cpu now and is called by a single caller.
The WARN_ON() isn't really required anymore, as we are just updating the
cpu now, not moving the sysfs directories.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_remove_dev_finish() is doing two things today:
- Restarts the governor if some CPUs from concerned policy are still
online.
- Frees the policy if all CPUs are offline.
The first task of restarting the governor can be moved to
__cpufreq_remove_dev_prepare() to restart the governor early. There is
no race between _prepare() and _finish() as they would be handling
completely different cases. _finish() will only be required if we are
going to free the policy and that has nothing to do with restarting the
governor.
Original-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_policy_put_kobj() is actually part of freeing the policy and can
be called from cpufreq_policy_free() directly instead of a separate
call.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->kobj is required to be initialized once in the lifetime of a
policy. Currently we are initializing it from __cpufreq_add_dev() and
that doesn't look to be the best place for doing so as we have to do
this on special cases (like: !recover_policy).
We can initialize it from a more obvious place cpufreq_policy_alloc()
and that will make code look cleaner, specially the error handling part.
The error handling part of __cpufreq_add_dev() was doing almost the same
thing while recover_policy is true or false. Fix that as well by always
calling cpufreq_policy_put_kobj() with an additional parameter to skip
notification part of it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When we hot-unplug a cpu, we remove its sysfs cpufreq directory and if
the outgoing cpu was the owner of policy->kobj earlier then we migrate
the sysfs directory to under another online cpu.
There are few disadvantages this brings:
- Code Complexity
- Slower hotplug/suspend/resume
- sysfs file permissions are reset after all policy->cpus are offlined
- CPUFreq stats history lost after all policy->cpus are offlined
- Special management of sysfs stuff during suspend/resume
To overcome these, this patch modifies the way sysfs directories are
managed:
- Select sysfs kobjects owner while initializing policy and don't change
it during hotplugs. Track it with kobj_cpu created earlier.
- Create symlinks for all related CPUs (can be offline) instead of
affected CPUs on policy initialization and remove them only when the
policy is freed.
- Free policy structure only on the removal of cpufreq-driver and not
during hotplug/suspend/resume, detected by checking 'struct
subsys_interface *' (Valid only when called from
subsys_interface_unregister() while unregistering driver).
Apart from this, special care is taken to handle physical hoplug of CPUs
as we wouldn't remove sysfs links or remove policies on logical
hotplugs. Physical hotplug happens in the following sequence.
Hot removal:
- CPU is offlined first, ~ 'echo 0 >
/sys/devices/system/cpu/cpuX/online'
- Then its device is removed along with all sysfs files, cpufreq core
notified with cpufreq_remove_dev() callback from subsys-interface..
Hot addition:
- First the device along with its sysfs files is added, cpufreq core
notified with cpufreq_add_dev() callback from subsys-interface..
- CPU is onlined, ~ 'echo 1 > /sys/devices/system/cpu/cpuX/online'
We call the same routines with both hotplug and subsys callbacks, and we
sense physical hotplug with cpu_offline() check in subsys callback. We
can handle most of the stuff with regular hotplug callback paths and
add/remove cpufreq sysfs links or free policy from subsys callbacks.
Original-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Later commits would change the way policies are managed today. Policies
wouldn't be freed on cpu hotplug (currently they aren't freed only for
suspend), and while the CPU is offline, the sysfs cpufreq files would
still be present.
User may accidentally try to update the sysfs files in following
directory: '/sys/devices/system/cpu/cpuX/cpufreq/'. And that would
result in undefined behavior as policy wouldn't be active then.
Apart from updating the store() routine, we also update __cpufreq_get()
which can call cpufreq_out_of_sync(). The later routine tries to update
policy->cur and starts notifying kernel about it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to prepare for the next few commits, that will stop migrating
sysfs files on cpu hotplug, this patch starts managing sysfs-cpu
separately.
The behavior is still the same as we are still migrating sysfs files on
hotplug, later commits would change that.
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Later commits would change the way policies are managed today. Policies
wouldn't be freed on cpu hotplug (currently they aren't freed on
suspend), and while the CPU is offline, the sysfs cpufreq files would
still be present.
Because we don't mark policy->governor as NULL, it still contains
pointer of the last used governor. And if the governor is removed, while
all the CPUs of a policy are hotplugged out, this pointer wouldn't be
valid anymore. And if we try to read the 'scaling_governor', etc. from
sysfs, it will result in kernel OOPs.
To prevent this, mark policy->governor as NULL for all inactive policies
while the governor is removed from kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
History of which governor was used last is common to all CPUs within a
policy and maintaining it per-cpu isn't the best approach for sure.
Apart from wasting memory, this also increases the complexity of
managing this data structure as it has to be updated for all CPUs.
To make that somewhat simpler, lets store this information in a new
field 'last_governor' in struct cpufreq_policy and update it on removal
of last cpu of a policy.
As a side-effect it also solves an old problem, consider a system with
two clusters 0 & 1. And there is one policy per cluster.
Cluster 0: CPU0 and 1.
Cluster 1: CPU2 and 3.
- CPU2 is first brought online, and governor is set to performance
(default as cpufreq_cpu_governor wasn't set).
- Governor is changed to ondemand.
- CPU2 is taken offline and cpufreq_cpu_governor is updated for CPU2.
- CPU3 is brought online.
- Because cpufreq_cpu_governor wasn't set for CPU3, the default governor
performance is picked for CPU3.
This patch fixes the bug as we now have a single variable to update for
policy.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We reach here while adding policy for a CPU and enter into the 'if'
block only if a policy already exists for the CPU.
As cpufreq_cpu_data is set for all policy->related_cpus now, when the
policy is first added, we can use that to find the CPU's policy instead
of traversing the list of all active policies.
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We can extract the same information from cpufreq_cpu_data as it is also
available for inactive policies now. And so don't need
cpufreq_cpu_data_fallback anymore.
Also add a WARN_ON() for the case where we try to restore from an active
policy.
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we can check policy->cpus to find if policy is active or not,
we don't need to clean cpufreq_cpu_data and delete policy from the list
on light weight tear down of policies (like in suspend).
To make it consistent and clean, set cpufreq_cpu_data for all related
CPUs when the policy is first created and clean it only while it is
freed.
Also update cpufreq_cpu_get_raw() to check if cpu is part of
policy->cpus mask, so that we don't end up getting policies for offline
CPUs.
In order to make sure that no users of 'policy' are using an inactive
policy, use cpufreq_cpu_get_raw() instead of directly accessing
cpufreq_cpu_data.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->cpus is cleared unconditionally now on hotplug-out of a CPU and
it can be checked to know if a policy is active or not. Create helper
routines to iterate over all active/inactive policies, based on
policy->cpus field.
Replace all instances of for_each_policy() with for_each_active_policy()
to make them iterate only for active policies. (We haven't made changes
yet to keep inactive policies in the same list, but that will be
followed in a later patch).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We clear policy->cpus mask while CPUs are hotplugged out. We do it for all CPUs
except the last CPU of the policy. I don't remember what the rationale behind
that was, but I couldn't think of anything that will break if we remove this
conditional clearing and always clear policy->cpus.
The benefit we get out of it is, we can know if a policy is active or not by
checking if this field is empty or not. That will be used by later commits.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two cases when we may try to add CPUs we're already handling:
- On boot, the first cpu has marked all policy->cpus managed and so we
will find policy for all other policy->cpus later on.
- When a managed cpu is hotplugged out and later brought back in.
Currently, separate paths and checks take care of the two. While the
first one is detected by testing cpu against 'policy->cpus', the other
one is detected by testing cpu against 'policy->related_cpus'.
We can handle them both via a single path and there is no need to do
special checking for the first one.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
[ rjw: Changelog, comments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Simply returning here with an error is not enough. It shouldn't be allowed at
all to try calling cpufreq_cpu_get() for an invalid CPU.
Add a WARN here to make it clear that it wouldn't be acceptable at all.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_add_dev() is an unnecessary wrapper over __cpufreq_add_dev(). Merge
them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This clearly states what the code inside these routines is doing and how these
must be used.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All CPUs leaving the first-online CPU are hotplugged out on suspend and
and cpufreq core stops managing them.
On resume, we need to call cpufreq_update_policy() for this CPU's policy
to make sure its frequency is in sync with cpufreq's cached value, as it
might have got updated by hardware during suspend/resume.
The policies are always added to the top of the policy-list. So, in
normal circumstances, CPU 0's policy will be the last one in the list.
And so the code checks for the last policy.
But there are cases where it will fail. Consider quad-core system, with
policy-per core. If CPU0 is hotplugged out and added back again, the
last policy will be on CPU1 :(
To fix this in a proper way, always look for the policy of the first
online CPU. That way we will be sure that we are calling
cpufreq_update_policy() for the only CPU that wasn't hotplugged out.
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Fixes: 2f0aea9363 ("cpufreq: suspend governors on system suspend/hibernate")
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To make code more readable and less error prone, lets create a helper macro for
iterating over all available governors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To make code more readable and less error prone, lets create a helper macro for
iterating over all active policies.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When cpufreq is disabled, the per-cpu variable would have been set to
NULL. Remove this unnecessary check.
[ Changelog from Saravana Kannan. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In __cpufreq_remove_dev_finish(), per-cpu 'cpufreq_cpu_data' needs
to be cleared before calling kobject_put(&policy->kobj) and under
cpufreq_driver_lock. Otherwise, if someone else calls cpufreq_cpu_get()
in parallel with it, they can obtain a non-NULL policy from that after
kobject_put(&policy->kobj) was executed.
Consider this case:
Thread A Thread B
cpufreq_cpu_get()
acquire cpufreq_driver_lock
read-per-cpu cpufreq_cpu_data
kobject_put(&policy->kobj);
kobject_get(&policy->kobj);
...
per_cpu(&cpufreq_cpu_data, cpu) = NULL
And this will result in a warning like this one:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 4 at include/linux/kref.h:47
kobject_get+0x41/0x50()
Modules linked in: acpi_cpufreq(+) nfsd auth_rpcgss nfs_acl
lockd grace sunrpc xfs libcrc32c sd_mod ixgbe igb mdio ahci hwmon
...
Call Trace:
[<ffffffff81661b14>] dump_stack+0x46/0x58
[<ffffffff81072b61>] warn_slowpath_common+0x81/0xa0
[<ffffffff81072c7a>] warn_slowpath_null+0x1a/0x20
[<ffffffff812e16d1>] kobject_get+0x41/0x50
[<ffffffff815262a5>] cpufreq_cpu_get+0x75/0xc0
[<ffffffff81527c3e>] cpufreq_update_policy+0x2e/0x1f0
[<ffffffff810b8cb2>] ? up+0x32/0x50
[<ffffffff81381aa9>] ? acpi_ns_get_node+0xcb/0xf2
[<ffffffff81381efd>] ? acpi_evaluate_object+0x22c/0x252
[<ffffffff813824f6>] ? acpi_get_handle+0x95/0xc0
[<ffffffff81360967>] ? acpi_has_method+0x25/0x40
[<ffffffff81391e08>] acpi_processor_ppc_has_changed+0x77/0x82
[<ffffffff81089566>] ? move_linked_works+0x66/0x90
[<ffffffff8138e8ed>] acpi_processor_notify+0x58/0xe7
[<ffffffff8137410c>] acpi_ev_notify_dispatch+0x44/0x5c
[<ffffffff8135f293>] acpi_os_execute_deferred+0x15/0x22
[<ffffffff8108c910>] process_one_work+0x160/0x410
[<ffffffff8108d05b>] worker_thread+0x11b/0x520
[<ffffffff8108cf40>] ? rescuer_thread+0x380/0x380
[<ffffffff81092421>] kthread+0xe1/0x100
[<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0
[<ffffffff81669ebc>] ret_from_fork+0x7c/0xb0
[<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0
---[ end trace 89e66eb9795efdf7 ]---
The actual code flow is as follows:
Thread A: Workqueue: kacpi_notify
acpi_processor_notify()
acpi_processor_ppc_has_changed()
cpufreq_update_policy()
cpufreq_cpu_get()
kobject_get()
Thread B: xenbus_thread()
xenbus_thread()
msg->u.watch.handle->callback()
handle_vcpu_hotplug_event()
vcpu_hotplug()
cpu_down()
__cpu_notify(CPU_POST_DEAD..)
cpufreq_cpu_callback()
__cpufreq_remove_dev_finish()
cpufreq_policy_put_kobj()
kobject_put()
cpufreq_cpu_get() gets the policy from per-cpu variable cpufreq_cpu_data
under cpufreq_driver_lock, and once it gets a valid policy it expects it
to not be freed until cpufreq_cpu_put() is called.
But the race happens when another thread puts the kobject first and updates
cpufreq_cpu_data before or later. And so the first thread gets a valid policy
structure and before it does kobject_get() on it, the second one has already
done kobject_put().
Fix this by setting cpufreq_cpu_data to NULL before putting the kobject and that
too under locks.
Reported-by: Ethan Zhao <ethan.zhao@oracle.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPUFREQ_UPDATE_POLICY_CPU notifications were used only from cpufreq-stats which
doesn't use it anymore. Remove them.
This also decrements values of other notification macros defined after
CPUFREQ_UPDATE_POLICY_CPU by 1 to remove gaps. Hopefully all users are using
macro's instead of direct numbers and so they wouldn't break as macro values are
changed now.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'last_cpu' was used only from cpufreq-stats and isn't used anymore. Get rid of
it.
Reviewed-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We need to initialize completion and work only on policy allocation and not
really on the policy restore side and so we better move this piece of code to
cpufreq_policy_alloc().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPUFREQ_STICKY flag is set by drivers which don't want to get unregistered
even if cpufreq-core isn't able to initialize policy for any CPU.
When this flag isn't set, we try to unregister the driver. To find out
which CPUs are registered and which are not, we try to check per_cpu
cpufreq_cpu_data for all CPUs. Because we have a list of valid policies
available now, we better check if the list is empty or not instead of
the 'for' loop. That will be much more efficient.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These variables are just used within adjust_jiffies() and so must be
local to it. Also there is no need of a dummy routine for CONFIG_SMP
case as we can take care of all that with help of macros in the same
routine. It doesn't look that ugly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We just need to check if a 'policy' is already present for the cpu we are
adding. We don't need to take all the locks and do kobject usage updates. Use
the light-weight cpufreq_cpu_get_raw() routine instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need of this separate variable, use 'policy' instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These are messing up more than the benefit they provide. It isn't
a lot of code anyway, that we will compile without them.
Kill them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We should first check if a cpufreq driver is already registered or not
before updating driver_data->flags.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no point finding out the 'policy' again within __cpufreq_get()
when all the callers already have it. Just make them pass policy instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no point finding out the 'policy' again within cpufreq_out_of_sync()
when all the callers already have it. Just make them pass policy instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Either we can be setpolicy or target type, nothing else. And so the
else part of setpolicy will automatically be of has_target() type.
And so we don't need to check it again.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove unnecessary from find_governor's name.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are two 'if' blocks here, checking for !cpufreq_driver->setpolicy and
has_target(). Both are actually doing the same thing, merge them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No need of an unnecessary line break.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We can live without it and so we should.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It doesn't make any sense at all and is a leftover of some earlier commit.
Remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We should stop cpufreq governors when we shut down the system. If we
don't do this, we can end up with this deadlock:
1. cpufreq governor may be running on a CPU other than CPU0.
2. In machine_restart() we call smp_send_stop() which stops CPUs.
If one of these CPUs was actively running a cpufreq governor
then it may have the mutex / spinlock needed to access the main
PMIC in the system (perhaps over I2C)
3. If a machine needs access to the main PMIC in order to shutdown
then it will never get it since the mutex was lost when the other
CPU stopped.
4. We'll hang (possibly eventually hitting the hard lockup detector).
Let's avoid the problem by stopping the cpufreq governor at shutdown,
which is a sensible thing to do anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently there is no callback for cpufreq drivers which is called once the
policy is ready to be used. There are some requirements where such a callback is
required.
One of them is registering a cooling device with the help of
of_cpufreq_cooling_register(). This routine tries to get 'struct cpufreq_policy'
for CPUs which isn't yet initialed at the time ->init() is called and so we face
issues while registering the cooling device.
Because we can't register cooling device from ->init(), we need a callback that
is called after the policy is ready to be used and hence we introduce ->ready()
callback.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Eduardo Valentin <edubezval@gmail.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Do it before it's assigned to cpufreq_cpu_data, otherwise when a driver
tries to get the cpu frequency during initialization the policy kobj is
referenced and we get this warning:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 64 at include/linux/kref.h:47 kobject_get+0x64/0x70()
Modules linked in:
CPU: 1 PID: 64 Comm: irq/77-tegra-ac Not tainted 3.18.0-rc4-next-20141114ccu-00050-g3eff942 #326
[<c0016fac>] (unwind_backtrace) from [<c001272c>] (show_stack+0x10/0x14)
[<c001272c>] (show_stack) from [<c06085d8>] (dump_stack+0x98/0xd8)
[<c06085d8>] (dump_stack) from [<c002892c>] (warn_slowpath_common+0x84/0xb4)
[<c002892c>] (warn_slowpath_common) from [<c00289f8>] (warn_slowpath_null+0x1c/0x24)
[<c00289f8>] (warn_slowpath_null) from [<c0220290>] (kobject_get+0x64/0x70)
[<c0220290>] (kobject_get) from [<c03e944c>] (cpufreq_cpu_get+0x88/0xc8)
[<c03e944c>] (cpufreq_cpu_get) from [<c03e9500>] (cpufreq_get+0xc/0x64)
[<c03e9500>] (cpufreq_get) from [<c0285288>] (actmon_thread_isr+0x134/0x198)
[<c0285288>] (actmon_thread_isr) from [<c0069008>] (irq_thread_fn+0x1c/0x40)
[<c0069008>] (irq_thread_fn) from [<c0069324>] (irq_thread+0x134/0x174)
[<c0069324>] (irq_thread) from [<c0040290>] (kthread+0xdc/0xf4)
[<c0040290>] (kthread) from [<c000f4b8>] (ret_from_fork+0x14/0x3c)
---[ end trace b7bd64a81b340c59 ]---
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the user space tries to set scaling_(max|min)_freq through
sysfs, the cpufreq_set_policy() asks other driver's opinions
for the max/min frequencies. Some device drivers, like Tegra
CPU EDP which is not upstreamed yet though, may constrain the
CPU maximum frequency dynamically because of board design.
So if the user space access happens and some driver is capping
the cpu frequency at the same time, the user_policy->(max|min)
is overridden by the capped value, and that's not expected by
the user space. And if the user space is not invoked again,
the CPU will always be capped by the user_policy->(max|min)
even no drivers limit the CPU frequency any more.
This patch preserves the user specified min/max settings, so that
every time the cpufreq policy is updated, the new max/min can
be re-evaluated correctly based on the user's expection and
the present device drivers' status.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When resuming from s2ram on an SMP system without cpufreq operating
points (e.g. there's no "operating-points" property for the CPU node in
DT, or the platform doesn't use DT yet), the kernel crashes when
bringing CPU 1 online:
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
Unable to handle kernel NULL pointer dereference at virtual address 0000003c
pgd = ee5e6b00
[0000003c] *pgd=6e579003, *pmd=6e588003, *pte=00000000
Internal error: Oops: a07 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1246 Comm: s2ram Tainted: G W 3.18.0-rc3-koelsch-01614-g0377af242bb175c8-dirty #589
task: eeec5240 ti: ee704000 task.ti: ee704000
PC is at __cpufreq_add_dev.isra.24+0x24c/0x77c
LR is at __cpufreq_add_dev.isra.24+0x244/0x77c
pc : [<c0298efc>] lr : [<c0298ef4>] psr: 60000153
sp : ee705d48 ip : ee705d48 fp : ee705d84
r10: c04e0450 r9 : 00000000 r8 : 00000001
r7 : c05426a8 r6 : 00000001 r5 : 00000001 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : 20000153 r0 : c0542734
Verify that policy is not NULL before dereferencing it to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: 8414809c6a (cpufreq: Preserve policy structure across suspend/resume)
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the core does not expose scaling_cur_freq for set_policy()
drivers this breaks some userspace monitoring tools.
Change the core to expose this file for all drivers and if the
set_policy() driver supports the get() callback use it to retrieve the
current frequency.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=73741
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This commit extends the cpufreq_driver structure with an additional
'void *driver_data' field that can be filled by the ->probe() function
of a cpufreq driver to pass additional custom information to the
driver itself.
A new function called cpufreq_get_driver_data() is added to allow a
cpufreq driver to retrieve those driver data, since they are typically
needed from a cpufreq_policy->init() callback, which does not have
access to the cpufreq_driver structure. This function call is similar
to the existing cpufreq_get_current_driver() function call.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 8e30444e15 ("cpufreq: fix cpufreq suspend/resume for intel_pstate")
introduced a bug where the governors wouldn't be stopped anymore for
->target{_index}() drivers during suspend. This happens because
'cpufreq_suspended' is updated before stopping the governors during suspend
and due to this __cpufreq_governor() would return early due to this check:
/* Don't start any governor operations if we are entering suspend */
if (cpufreq_suspended)
return 0;
Fixes: 8e30444e15 ("cpufreq: fix cpufreq suspend/resume for intel_pstate")
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+: 8e30444e15 "cpufreq: fix cpufreq suspend/resume for intel_pstate"
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics
and a slightly buggy strncasecmp. The latter is the POSIX name, so
strnicmp was renamed to strncasecmp, and strnicmp made into a wrapper
for the new strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in
the future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 367dc4aa93 ("cpufreq: Add stop CPU callback to
cpufreq_driver interface") introduced the stop CPU callback for
intel_pstate drivers. During the CPU_DOWN_PREPARE stage, this
callback is invoked so that drivers can take some action on the
pstate of the cpu before it is taken offline. This callback was
assumed to be useful only for those drivers which have implemented
the set_policy CPU callback because they have no other way to take
action about the cpufreq of a CPU which is being hotplugged out
except in the exit callback which is called very late in the offline
process.
The drivers which implement the target/target_index callbacks were
expected to take care of requirements like the ones that commit
367dc4aa addresses in the GOV_STOP notification event. But there
are disadvantages to restricting the usage of stop CPU callback
to cpufreq drivers that implement the set_policy callbacks and who
want to take explicit action on the setting the cpufreq during a
hotplug operation.
1.GOV_STOP gets called for every CPU offline and drivers would usually
want to take action when the last cpu in the policy->cpus mask
is taken offline. As long as there is more than one cpu in the
policy->cpus mask, cpufreq core itself makes sure that the freq
for the other cpus in this mask is set according to the maximum load.
This is sensible and drivers which implement the target_index callback
would mostly not want to modify that. However the cpufreq core leaves a
loose end when the cpu in the policy->cpus mask is the last one to go offline;
it does nothing explicit to the frequency of the core. Drivers may need
a way to take some action here and stop CPU callback mechanism is the
best way to do it today.
2. We cannot implement driver specific actions in the GOV_STOP mechanism.
So we will need another driver callback which is invoked from here which is
unnecessary.
Therefore this patch extends the usage of stop CPU callback to be used
by all cpufreq drivers as long as they have this callback implemented
and irrespective of whether they are set_policy/target_index drivers.
The assumption is if the drivers find the GOV_STOP path to be a suitable
way of implementing what they want to do with the freq of the cpu
going offine,they will not implement the stop CPU callback at all.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While debugging a cpufreq-related hardware failure on a system I saw the
following lockdep warning:
=========================
[ BUG: held lock freed! ] 3.17.0-rc4+ #1 Tainted: G E
-------------------------
insmod/2247 is freeing memory ffff88006e1b1400-ffff88006e1b17ff, with a lock still held there!
(&policy->rwsem){+.+...}, at: [<ffffffff8156d37d>] __cpufreq_add_dev.isra.21+0x47d/0xb80
3 locks held by insmod/2247:
#0: (subsys mutex#5){+.+.+.}, at: [<ffffffff81485579>] subsys_interface_register+0x69/0x120
#1: (cpufreq_rwsem){.+.+.+}, at: [<ffffffff8156cf73>] __cpufreq_add_dev.isra.21+0x73/0xb80
#2: (&policy->rwsem){+.+...}, at: [<ffffffff8156d37d>] __cpufreq_add_dev.isra.21+0x47d/0xb80
stack backtrace:
CPU: 0 PID: 2247 Comm: insmod Tainted: G E 3.17.0-rc4+ #1
Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 08/24/2013
0000000000000000 000000008f3063c4 ffff88006f87bb30 ffffffff8171b358
ffff88006bcf3750 ffff88006f87bb68 ffffffff810e09e1 ffff88006e1b1400
ffffea0001b86c00 ffffffff8156d327 ffff880073003500 0000000000000246
Call Trace:
[<ffffffff8171b358>] dump_stack+0x4d/0x66
[<ffffffff810e09e1>] debug_check_no_locks_freed+0x171/0x180
[<ffffffff8156d327>] ? __cpufreq_add_dev.isra.21+0x427/0xb80
[<ffffffff8121412b>] kfree+0xab/0x2b0
[<ffffffff8156d327>] __cpufreq_add_dev.isra.21+0x427/0xb80
[<ffffffff81724cf7>] ? _raw_spin_unlock+0x27/0x40
[<ffffffffa003517f>] ? pcc_cpufreq_do_osc+0x17f/0x17f [pcc_cpufreq]
[<ffffffff8156da8e>] cpufreq_add_dev+0xe/0x10
[<ffffffff814855d1>] subsys_interface_register+0xc1/0x120
[<ffffffff8156bcf2>] cpufreq_register_driver+0x112/0x340
[<ffffffff8121415a>] ? kfree+0xda/0x2b0
[<ffffffffa003517f>] ? pcc_cpufreq_do_osc+0x17f/0x17f [pcc_cpufreq]
[<ffffffffa003562e>] pcc_cpufreq_init+0x4af/0xe81 [pcc_cpufreq]
[<ffffffffa003517f>] ? pcc_cpufreq_do_osc+0x17f/0x17f [pcc_cpufreq]
[<ffffffff81002144>] do_one_initcall+0xd4/0x210
[<ffffffff811f7472>] ? __vunmap+0xd2/0x120
[<ffffffff81127155>] load_module+0x1315/0x1b70
[<ffffffff811222a0>] ? store_uevent+0x70/0x70
[<ffffffff811229d9>] ? copy_module_from_fd.isra.44+0x129/0x180
[<ffffffff81127b86>] SyS_finit_module+0xa6/0xd0
[<ffffffff81725b69>] system_call_fastpath+0x16/0x1b
cpufreq: __cpufreq_add_dev: ->get() failed
insmod: ERROR: could not insert module pcc-cpufreq.ko: No such device
The warning occurs in the __cpufreq_add_dev() code which does
down_write(&policy->rwsem);
...
if (cpufreq_driver->get && !cpufreq_driver->setpolicy) {
policy->cur = cpufreq_driver->get(policy->cpu);
if (!policy->cur) {
pr_err("%s: ->get() failed\n", __func__);
goto err_get_freq;
}
If cpufreq_driver->get(policy->cpu) returns an error we execute the
code at err_get_freq, which does not up the policy->rwsem. This causes
the lockdep warning.
Trivial patch to up the policy->rwsem in the error path.
After the patch has been applied, and an error occurs in the
cpufreq_driver->get(policy->cpu) call we will now see
cpufreq: __cpufreq_add_dev: ->get() failed
cpufreq: __cpufreq_add_dev: ->get() failed
modprobe: ERROR: could not insert 'pcc_cpufreq': No such device
Fixes: 4e97b631f2 (cpufreq: Initialize governor for a new policy under policy->rwsem)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cpufreq core introduces cpufreq_suspended flag to let cpufreq sysfs nodes
across S2RAM/S2DISK. But the flag is only set in the cpufreq_suspend()
for cpufreq drivers which have target or target_index callback. This
skips intel_pstate driver. This patch is to set the flag before checking
target or target_index callback.
Fixes: 2f0aea9363 (cpufreq: suspend governors on system suspend/hibernate)
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
[rjw: Subject]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We are calling kobject_move() from two separate places currently and both these
places share another routine update_policy_cpu() which is handling everything
around updating policy->cpu. Moving ownership of policy->kobj also lies under
the role of update_policy_cpu() routine and must be handled from there.
So, Lets move kobject_move() to update_policy_cpu() and get rid of
cpufreq_nominate_new_policy_cpu() as it doesn't have anything significant left.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We are returning -EINVAL instead of the error returned from kobject_move() when
it fails. Propagate the actual error number.
Also add a meaningful print when sysfs_create_link() fails.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While hot-unplugging policy->cpu, we call cpufreq_nominate_new_policy_cpu() to
nominate next owner of policy, i.e. policy->cpu. If we fail to move policy
kobject under the new policy->cpu, we try to update policy->cpus with the old
policy->cpu.
This would have been required in case old-CPU is removed from policy->cpus in
the first place. But its not done before calling
cpufreq_nominate_new_policy_cpu(), but during the POST_DEAD notification which
happens quite late in the hot-unplugging path.
So, this is just some useless code hanging around, get rid of it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is only relevant to implementations with multiple clusters, where clusters
have separate clock lines but all CPUs within a cluster share it.
Consider a dual cluster platform with 2 cores per cluster. During suspend we
start hot unplugging CPUs in order 1 to 3. When CPU2 is removed, policy->kobj
would be moved to CPU3 and when CPU3 goes down we wouldn't free policy or its
kobj as we want to retain permissions/values/etc.
Now on resume, we will get CPU2 before CPU3 and will call __cpufreq_add_dev().
We will recover the old policy and update policy->cpu from 3 to 2 from
update_policy_cpu().
But the kobj is still tied to CPU3 and isn't moved to CPU2. We wouldn't create a
link for CPU2, but would try that for CPU3 while bringing it online. Which will
report errors as CPU3 already has kobj assigned to it.
This bug got introduced with commit 42f921a, which overlooked this scenario.
To fix this, lets move kobj to the new policy->cpu while bringing first CPU of a
cluster back. Also do a WARN_ON() if kobject_move failed, as we would reach here
only for the first CPU of a non-boot cluster. And we can't recover from this
situation, if kobject_move() fails.
Fixes: 42f921a6f1 (cpufreq: remove sysfs files for CPUs which failed to come back after resume)
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Reported-and-tested-by: Bu Yitian <ybu@qti.qualcomm.com>
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa@mit.edu>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit bd0fa9bb45 introduced a failure path to cpufreq_update_policy() if
cpufreq_driver->get(cpu) returns NULL. However, it jumps to the 'no_policy'
label, which exits without unlocking any of the locks the function acquired
earlier. This causes later calls into cpufreq to hang.
Fix this by creating a new 'unlock' label and jumping to that instead.
Fixes: bd0fa9bb45 ("cpufreq: Return error if ->get() failed in cpufreq_update_policy()")
Link: https://devtalk.nvidia.com/default/topic/751903/kernel-3-15-and-nv-drivers-337-340-failed-to-initialize-the-nvidia-kernel-module-gtx-550-ti-/
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Douglas Anderson, recently pointed out an interesting problem due to which
udelay() was expiring earlier than it should.
While transitioning between frequencies few platforms may temporarily switch to
a stable frequency, waiting for the main PLL to stabilize.
For example: When we transition between very low frequencies on exynos, like
between 200MHz and 300MHz, we may temporarily switch to a PLL running at 800MHz.
No CPUFREQ notification is sent for that. That means there's a period of time
when we're running at 800MHz but loops_per_jiffy is calibrated at between 200MHz
and 300MHz. And so udelay behaves badly.
To get this fixed in a generic way, introduce another set of callbacks
get_intermediate() and target_intermediate(), only for drivers with
target_index() and CPUFREQ_ASYNC_NOTIFICATION unset.
get_intermediate() should return a stable intermediate frequency platform wants
to switch to, and target_intermediate() should set CPU to that frequency,
before jumping to the frequency corresponding to 'index'. Core will take care of
sending notifications and driver doesn't have to handle them in
target_intermediate() or target_index().
NOTE: ->target_index() should restore to policy->restore_freq in case of
failures as core would send notifications for that.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Handling calls to ->target_index() has got complex over time and might become
more complex. So, its better to take target_index() bits out in another routine
__target_index() for better code readability. Shouldn't have any functional
impact.
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On platforms that use cpufreq_for_each_* macros, build fails if
CONFIG_CPU_FREQ=n, e.g. ARM/shmobile/koelsch/non-multiplatform:
drivers/built-in.o: In function `clk_round_parent':
clkdev.c:(.text+0xcf168): undefined reference to `cpufreq_next_valid'
drivers/built-in.o: In function `clk_rate_table_find':
clkdev.c:(.text+0xcf820): undefined reference to `cpufreq_next_valid'
make[3]: *** [vmlinux] Error 1
Fix this making cpufreq_next_valid function inline and move it to
cpufreq.h.
Fixes: 27e289dce2 (cpufreq: Introduce macros for cpufreq_frequency_table iteration)
Reported-and-tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some cpufreq drivers were redundantly invoking the _begin() and _end()
APIs around frequency transitions, and this double invocation (one from
the cpufreq core and the other from the cpufreq driver) used to result
in a self-deadlock, leading to system hangs during boot. (The _begin()
API makes contending callers wait until the previous invocation is
complete. Hence, the cpufreq driver would end up waiting on itself!).
Now all such drivers have been fixed, but debugging this issue was not
very straight-forward (even lockdep didn't catch this). So let us add a
debug infrastructure to the cpufreq core to catch such issues more easily
in the future.
We add a new field called 'transition_task' to the policy structure, to keep
track of the task which is performing the frequency transition. Using this
field, we make note of this task during _begin() and print a warning if we
find a case where the same task is calling _begin() again, before completing
the previous frequency transition using the corresponding _end().
We have left out ASYNC_NOTIFICATION drivers from this debug infrastructure
for 2 reasons:
1. At the moment, we have no way to avoid a particular scenario where this
debug infrastructure can emit false-positive warnings for such drivers.
The scenario is depicted below:
Task A Task B
/* 1st freq transition */
Invoke _begin() {
...
...
}
Change the frequency
/* 2nd freq transition */
Invoke _begin() {
... //waiting for B to
... //finish _end() for
... //the 1st transition
... | Got interrupt for successful
... | change of frequency (1st one).
... |
... | /* 1st freq transition */
... | Invoke _end() {
... | ...
... V }
...
...
}
This scenario is actually deadlock-free because, once Task A changes the
frequency, it is Task B's responsibility to invoke the corresponding
_end() for the 1st frequency transition. Hence it is perfectly legal for
Task A to go ahead and attempt another frequency transition in the meantime.
(Of course it won't be able to proceed until Task B finishes the 1st _end(),
but this doesn't cause a deadlock or a hang).
The debug infrastructure cannot handle this scenario and will treat it as
a deadlock and print a warning. To avoid this, we exclude such drivers
from the purview of this code.
2. Luckily, we don't _need_ this infrastructure for ASYNC_NOTIFICATION drivers
at all! The cpufreq core does not automatically invoke the _begin() and
_end() APIs during frequency transitions in such drivers. Thus, the driver
alone is responsible for invoking _begin()/_end() and hence there shouldn't
be any conflicts which lead to double invocations. So, we can skip these
drivers, since the probability that such drivers will hit this problem is
extremely low, as outlined above.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many cpufreq drivers need to iterate over the cpufreq_frequency_table
for various tasks.
This patch introduces two macros which can be used for iteration over
cpufreq_frequency_table keeping a common coding style across drivers:
- cpufreq_for_each_entry: iterate over each entry of the table
- cpufreq_for_each_valid_entry: iterate over each entry that contains
a valid frequency.
It should have no functional changes.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_notify_transition() and cpufreq_notify_post_transition() shouldn't be
called directly by cpufreq drivers anymore and so these should be marked static.
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPUFreq core has new infrastructure that would guarantee serialized calls to
target() or target_index() callbacks. These are called
cpufreq_freq_transition_begin() and cpufreq_freq_transition_end().
This patch converts existing drivers to use these new set of routines.
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Whenever we change the frequency of a CPU, we call the PRECHANGE and POSTCHANGE
notifiers. They must be serialized, i.e. PRECHANGE and POSTCHANGE notifiers
should strictly alternate, thereby preventing two different sets of PRECHANGE or
POSTCHANGE notifiers from interleaving arbitrarily.
The following examples illustrate why this is important:
Scenario 1:
-----------
A thread reading the value of cpuinfo_cur_freq, will call
__cpufreq_cpu_get()->cpufreq_out_of_sync()->cpufreq_notify_transition()
The ondemand governor can decide to change the frequency of the CPU at the same
time and hence it can end up sending the notifications via ->target().
If the notifiers are not serialized, the following sequence can occur:
- PRECHANGE Notification for freq A (from cpuinfo_cur_freq)
- PRECHANGE Notification for freq B (from target())
- Freq changed by target() to B
- POSTCHANGE Notification for freq B
- POSTCHANGE Notification for freq A
We can see from the above that the last POSTCHANGE Notification happens for freq
A but the hardware is set to run at freq B.
Where would we break then?: adjust_jiffies() in cpufreq.c & cpufreq_callback()
in arch/arm/kernel/smp.c (which also adjusts the jiffies). All the
loops_per_jiffy calculations will get messed up.
Scenario 2:
-----------
The governor calls __cpufreq_driver_target() to change the frequency. At the
same time, if we change scaling_{min|max}_freq from sysfs, it will end up
calling the governor's CPUFREQ_GOV_LIMITS notification, which will also call
__cpufreq_driver_target(). And hence we end up issuing concurrent calls to
->target().
Typically, platforms have the following logic in their ->target() routines:
(Eg: cpufreq-cpu0, omap, exynos, etc)
A. If new freq is more than old: Increase voltage
B. Change freq
C. If new freq is less than old: decrease voltage
Now, if the two concurrent calls to ->target() are X and Y, where X is trying to
increase the freq and Y is trying to decrease it, we get the following race
condition:
X.A: voltage gets increased for larger freq
Y.A: nothing happens
Y.B: freq gets decreased
Y.C: voltage gets decreased
X.B: freq gets increased
X.C: nothing happens
Thus we can end up setting a freq which is not supported by the voltage we have
set. That will probably make the clock to the CPU unstable and the system might
not work properly anymore.
This patch introduces a set of synchronization primitives to serialize frequency
transitions, which are to be used as shown below:
cpufreq_freq_transition_begin();
//Perform the frequency change
cpufreq_freq_transition_end();
The _begin() call sends the PRECHANGE notification whereas the _end() call sends
the POSTCHANGE notification. Also, all the necessary synchronization is handled
within these calls. In particular, even drivers which set the ASYNC_NOTIFICATION
flag can also use these APIs for performing frequency transitions (ie., you can
call _begin() from one task, and call the corresponding _end() from a different
task).
The actual synchronization underneath is not that complicated:
The key challenge is to allow drivers to begin the transition from one thread
and end it in a completely different thread (this is to enable drivers that do
asynchronous POSTCHANGE notification from bottom-halves, to also use the same
interface).
To achieve this, a 'transition_ongoing' flag, a 'transition_lock' spinlock and a
wait-queue are added per-policy. The flag and the wait-queue are used in
conjunction to create an "uninterrupted flow" from _begin() to _end(). The
spinlock is used to ensure that only one such "flow" is in flight at any given
time. Put together, this provides us all the necessary synchronization.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During suspend, we first stop governors and then suspend cpufreq drivers and
resume must be exactly opposite of that. i.e. resume drivers first and then
start governors.
But the current code in resume enables governors first and then resume drivers.
Fix it be changing code sequence there.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This callback allows the driver to do clean up before the CPU is
completely down and its state cannot be modified. This is used
by the intel_pstate driver to reduce the requested P state prior to
the core going away. This is required because the requested P state
of the offline core is used to select the package P state. This
effectively sets the floor package P state to the requested P state on
the offline core.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
[rjw: Minor modifications]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove unnecessary braces from a single statement.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix 2 checkpatch errors about using assignment in if condition,
1 checkpatch error about a required space after comma
and 3 warnings about line over 80 characters.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Two cpufreq notifiers CPUFREQ_RESUMECHANGE and CPUFREQ_SUSPENDCHANGE have
not been used for some time, so remove them to clean up code a bit.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq drivers that provide the ->setpolicy() callback are supposed
to have integrated governors, so they don't need to set ->target()
or ->target_index() and may confuse the core if any of these callbacks
is present.
For this reason, add a check preventing ->setpolicy cpufreq drivers
from registering if they have non-NULL ->target or ->target_index.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
After commit da60ce9f2f (cpufreq: call cpufreq_driver->get() after
calling ->init()) __cpufreq_add_dev() sometimes fails for CPUs handled
by intel_pstate, because that driver may return 0 from its ->get()
callback if it has not run long enough to collect enough samples on the
given CPU. That didn't happen before commit da60ce9f2f which added
policy->cur initialization to __cpufreq_add_dev() to help reduce code
duplication in other cpufreq drivers.
However, the code added by commit da60ce9f2f need not be executed
for cpufreq drivers having the ->setpolicy callback defined, because
the subsequent invocation of cpufreq_set_policy() will use that
callback to initialize the policy anyway and it doesn't need
policy->cur to be initialized upfront. The analogous code in
cpufreq_update_policy() is also unnecessary for cpufreq drivers
having ->setpolicy set and may be skipped for them as well.
Since intel_pstate provides ->setpolicy, skipping the upfront
policy->cur initialization for cpufreq drivers with that callback
set will cover intel_pstate and the problem it's been having after
commit da60ce9f2f will be addressed.
Fixes: da60ce9f2f (cpufreq: call cpufreq_driver->get() after calling ->init())
References: https://bugzilla.kernel.org/show_bug.cgi?id=71931
Reported-and-tested-by: Patrik Lundquist <patrik.lundquist@gmail.com>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have used 'frozen' variable/function parameter at many places to
distinguish between CPU offline/online on suspend/resume vs sysfs
removals. We now have another variable cpufreq_suspended which can
be used in these cases, so we can get rid of all those variables or
function parameters.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
freq table is not per CPU but per policy, so it makes more sense to
keep it within struct cpufreq_policy instead of a per-cpu variable.
This patch does it. Over that, there is no need to set policy->freq_table
to NULL in ->exit(), as policy structure is going to be freed soon.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Multiple platforms need to set CPUs to a particular frequency before
suspending the system, so provide a common infrastructure for them.
Those platforms only need to point their ->suspend callback pointers
to the generic routine.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds cpufreq suspend/resume calls to dpm_{suspend|resume}()
for handling suspend/resume of cpufreq governors.
Lan Tianyu (Intel) & Jinhyuk Choi (Broadcom) found an issue where the
tunables configuration for clusters/sockets with non-boot CPUs was
lost after system suspend/resume, as we were notifying governors with
CPUFREQ_GOV_POLICY_EXIT on removal of the last CPU for that policy
which caused the tunables memory to be freed.
This is fixed by preventing any governor operations from being
carried out between the device suspend and device resume stages of
system suspend and resume, respectively.
We could have added these callbacks at dpm_{suspend|resume}_noirq()
level, but there is an additional problem that the majority of I/O
devices is already suspended at that point and if cpufreq drivers
want to change the frequency before suspending, then that not be
possible on some platforms (which depend on peripherals like i2c,
regulators, etc).
Reported-and-tested-by: Lan Tianyu <tianyu.lan@intel.com>
Reported-by: Jinhyuk Choi <jinchoi@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We call __find_governor() during the addition of the first CPU of
each policy from __cpufreq_add_dev() to find the last governor used
for this CPU before it was hot-removed.
After that we call cpufreq_parse_governor() in cpufreq_init_policy(),
either with this governor, or with the default governor. Right after
that policy->governor is set to NULL.
While that code is not functionally problematic, the structure of it
is suboptimal, because some of the code required in cpufreq_init_policy()
is being executed by its caller, __cpufreq_add_dev(). So, it would make
more sense to get all of it together in a single place to make code more
readable.
Accordingly, move the code needed for policy initialization to
cpufreq_init_policy() and initialize policy->governor to NULL at the
beginning.
In order to clean up the code a bit more, some of the #ifdefs for
CONFIG_HOTPLUG_CPU are dropped too.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->rwsem is used to lock access to all parts of code modifying
struct cpufreq_policy, but it's not used on a new policy created by
__cpufreq_add_dev().
Because of that, if cpufreq_update_policy() is called in a tight loop
on one CPU in parallel with offline/online of another CPU, then the
following crash can be triggered:
Unable to handle kernel NULL pointer dereference at virtual address 00000020
pgd = c0003000
[00000020] *pgd=80000000004003, *pmd=00000000
Internal error: Oops: 206 [#1] PREEMPT SMP ARM
PC is at __cpufreq_governor+0x10/0x1ac
LR is at cpufreq_update_policy+0x114/0x150
---[ end trace f23a8defea6cd706 ]---
Kernel panic - not syncing: Fatal exception
CPU0: stopping
CPU: 0 PID: 7136 Comm: mpdecision Tainted: G D W 3.10.0-gd727407-00074-g979ede8 #396
[<c0afe180>] (notifier_call_chain+0x40/0x68) from [<c02a23ac>] (__blocking_notifier_call_chain+0x40/0x58)
[<c02a23ac>] (__blocking_notifier_call_chain+0x40/0x58) from [<c02a23d8>] (blocking_notifier_call_chain+0x14/0x1c)
[<c02a23d8>] (blocking_notifier_call_chain+0x14/0x1c) from [<c0803c68>] (cpufreq_set_policy+0xd4/0x2b8)
[<c0803c68>] (cpufreq_set_policy+0xd4/0x2b8) from [<c0803e7c>] (cpufreq_init_policy+0x30/0x98)
[<c0803e7c>] (cpufreq_init_policy+0x30/0x98) from [<c0805a18>] (__cpufreq_add_dev.isra.17+0x4dc/0x7a4)
[<c0805a18>] (__cpufreq_add_dev.isra.17+0x4dc/0x7a4) from [<c0805d38>] (cpufreq_cpu_callback+0x58/0x84)
[<c0805d38>] (cpufreq_cpu_callback+0x58/0x84) from [<c0afe180>] (notifier_call_chain+0x40/0x68)
[<c0afe180>] (notifier_call_chain+0x40/0x68) from [<c02812dc>] (__cpu_notify+0x28/0x44)
[<c02812dc>] (__cpu_notify+0x28/0x44) from [<c0aeed90>] (_cpu_up+0xf4/0x1dc)
[<c0aeed90>] (_cpu_up+0xf4/0x1dc) from [<c0aeeed4>] (cpu_up+0x5c/0x78)
[<c0aeeed4>] (cpu_up+0x5c/0x78) from [<c0aec808>] (store_online+0x44/0x74)
[<c0aec808>] (store_online+0x44/0x74) from [<c03a40f4>] (sysfs_write_file+0x108/0x14c)
[<c03a40f4>] (sysfs_write_file+0x108/0x14c) from [<c03517d4>] (vfs_write+0xd0/0x180)
[<c03517d4>] (vfs_write+0xd0/0x180) from [<c0351ca8>] (SyS_write+0x38/0x68)
[<c0351ca8>] (SyS_write+0x38/0x68) from [<c0205de0>] (ret_fast_syscall+0x0/0x30)
Fix that by taking locks at appropriate places in __cpufreq_add_dev()
as well.
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Suggested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Policy must be fully initialized before it is being made available
for use by others. Otherwise cpufreq_cpu_get() would be able to grab
a half initialized policy structure that might not have affected_cpus
(for example) populated. Then, anybody accessing those fields will get
a wrong value and that will lead to unpredictable results.
In order to fix this, do all the necessary initialization before we
make the policy structure available via cpufreq_cpu_get(). That will
guarantee that any code accessing fields of the policy will get
correct data from them.
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a module calls cpufreq_get while cpufreq is initializing, it's
possible for it to be called after cpufreq_driver is set but before
cpufreq_cpu_data is written during subsys_interface_register. This
happens because cpufreq_get doesn't take the cpufreq_driver_lock
around its use of cpufreq_cpu_data.
Fix this by using cpufreq_cpu_get(cpu) to look up the policy rather
than reading it out of cpufreq_cpu_data directly. cpufreq_cpu_get()
takes the appropriate locks to prevent this race from happening.
Since it's possible for policy to be NULL if the caller passes in an
invalid CPU number or calls the function before cpufreq is initialized,
delete the BUG_ON(!policy) and simply return 0. Don't try to return
-ENOENT because that's negative and the function returns an unsigned
integer.
References: https://bbs.archlinux.org/viewtopic.php?id=177934
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_update_policy() calls cpufreq_driver->get() to get current
frequency of a CPU and it is not supposed to fail or return zero.
Return error in case that happens.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Mark function as static in cpufreq.c because it is not
used outside this file.
This eliminates the following warning in cpufreq.c:
drivers/cpufreq/cpufreq.c:355:9: warning: no previous prototype for ‘show_boost’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_update_policy() is called from two places currently. From a
workqueue handled queued from cpufreq_bp_resume() for boot CPU and
from cpufreq_cpu_callback() whenever a CPU is added.
The first one makes sure that boot CPU is running on the frequency
present in policy->cpu. But we don't really need a call from
cpufreq_cpu_callback(), because we always call cpufreq_driver->init()
(which will set policy->cur correctly) whenever first CPU of any
policy is added back. And so every policy structure is guaranteed to
have the right frequency in policy->cur.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reduce the rampant usage of goto and the indentation level in
cpufreq_set_policy() to improve the readability of that code.
No functional changes should result from that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Commit 42f921a (cpufreq: remove sysfs files for CPUs which failed to
come back after resume) tried to do this but missed this piece of code
to fix.
Currently we are getting this on suspend/resume:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 877 at fs/sysfs/dir.c:52 sysfs_warn_dup+0x68/0x84()
sysfs: cannot create duplicate filename '/devices/system/cpu/cpu1/cpufreq'
Modules linked in: brcmfmac brcmutil
CPU: 0 PID: 877 Comm: test-rtc-resume Not tainted 3.14.0-rc2-00259-g9398a10cd964 #12
[<c0015bac>] (unwind_backtrace) from [<c0011850>] (show_stack+0x10/0x14)
[<c0011850>] (show_stack) from [<c056e018>] (dump_stack+0x80/0xcc)
[<c056e018>] (dump_stack) from [<c0025e44>] (warn_slowpath_common+0x64/0x88)
[<c0025e44>] (warn_slowpath_common) from [<c0025efc>] (warn_slowpath_fmt+0x30/0x40)
[<c0025efc>] (warn_slowpath_fmt) from [<c012776c>] (sysfs_warn_dup+0x68/0x84)
[<c012776c>] (sysfs_warn_dup) from [<c0127a54>] (sysfs_do_create_link_sd+0xb0/0xb8)
[<c0127a54>] (sysfs_do_create_link_sd) from [<c038ef64>] (__cpufreq_add_dev.isra.27+0x2a8/0x814)
[<c038ef64>] (__cpufreq_add_dev.isra.27) from [<c038f548>] (cpufreq_cpu_callback+0x70/0x8c)
[<c038f548>] (cpufreq_cpu_callback) from [<c0043864>] (notifier_call_chain+0x44/0x84)
[<c0043864>] (notifier_call_chain) from [<c0025f60>] (__cpu_notify+0x28/0x44)
[<c0025f60>] (__cpu_notify) from [<c00261e8>] (_cpu_up+0xf0/0x140)
[<c00261e8>] (_cpu_up) from [<c0569eb8>] (enable_nonboot_cpus+0x68/0xb0)
[<c0569eb8>] (enable_nonboot_cpus) from [<c006339c>] (suspend_devices_and_enter+0x198/0x2dc)
[<c006339c>] (suspend_devices_and_enter) from [<c0063654>] (pm_suspend+0x174/0x1e8)
[<c0063654>] (pm_suspend) from [<c00624e0>] (state_store+0x6c/0xbc)
[<c00624e0>] (state_store) from [<c01fc200>] (kobj_attr_store+0x14/0x20)
[<c01fc200>] (kobj_attr_store) from [<c0126e50>] (sysfs_kf_write+0x44/0x48)
[<c0126e50>] (sysfs_kf_write) from [<c012a274>] (kernfs_fop_write+0xb4/0x14c)
[<c012a274>] (kernfs_fop_write) from [<c00d4818>] (vfs_write+0xa8/0x180)
[<c00d4818>] (vfs_write) from [<c00d4bb8>] (SyS_write+0x3c/0x70)
[<c00d4bb8>] (SyS_write) from [<c000e620>] (ret_fast_syscall+0x0/0x30)
---[ end trace 76969904b614c18f ]---
Fix this by removing sysfs link for cpufreq directory when cpu removed
isn't policy->cpu.
Revamps: 42f921a (cpufreq: remove sysfs files for CPUs which failed to come back after resume)
Reported-and-tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This commit adds boost frequency support in cpufreq core (Hardware &
Software). Some SoCs (like Exynos4 - e.g. 4x12) allow setting frequency
above its normal operation limits. Such mode shall be only used for a
short time.
Overclocking (boost) support is essentially provided by platform
dependent cpufreq driver.
This commit unifies support for SW and HW (Intel) overclocking solutions
in the core cpufreq driver. Previously the "boost" sysfs attribute was
defined in the ACPI processor driver code. By default boost is disabled.
One global attribute is available at: /sys/devices/system/cpu/cpufreq/boost.
It only shows up when cpufreq driver supports overclocking.
Under the hood frequencies dedicated for boosting are marked with a
special flag (CPUFREQ_BOOST_FREQ) at driver's frequency table.
It is the user's concern to enable/disable overclocking with a proper call
to sysfs.
The cpufreq_boost_trigger_state() function is defined non static on purpose.
It is used later with thermal subsystem to provide automatic enable/disable
of the BOOST feature.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPUFreq drivers that use clock frameworks interface,i.e. clk_get_rate(),
to get CPUs clk rate, have similar sort of code used in most of them.
This patch adds a generic ->get() which will do the same thing for them.
All those drivers are required to now is to set .get to cpufreq_generic_get()
and set their clk pointer in policy->clk during ->init().
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are several problems with cpufreq stats in the way it handles
cpufreq_unregister_driver() and suspend/resume..
- We must not lose data collected so far when suspend/resume happens
and so stats directories must not be removed/allocated during these
operations, which is done currently.
- cpufreq_stat has registered notifiers with both cpufreq and hotplug.
It adds sysfs stats directory with a cpufreq notifier: CPUFREQ_NOTIFY
and removes this directory with a notifier from hotplug core.
In case cpufreq_unregister_driver() is called (on rmmod cpufreq driver),
stats directories per cpu aren't removed as CPUs are still online. The
only call cpufreq_stats gets is cpufreq_stats_update_policy_cpu() for
all CPUs except the last of each policy. And pointer to stat information
is stored in the entry for last CPU in the per-cpu cpufreq_stats_table.
But policy structure would be freed inside cpufreq core and so that will
result in memory leak inside cpufreq stats (as we are never freeing
memory for stats).
Now if we again insert the module cpufreq_register_driver() will be
called and we will again allocate stats data and put it on for first
CPU of every policy. In case we only have a single CPU per policy, we
will return with a error from cpufreq_stats_create_table() due to this
code:
if (per_cpu(cpufreq_stats_table, cpu))
return -EBUSY;
And so probably cpufreq stats directory would not show up anymore (as
it was added inside last policies->kobj which doesn't exist anymore).
I haven't tested it, though. Also the values in stats files wouldn't
be refreshed as we are using the earlier stats structure.
- CPUFREQ_NOTIFY is called from cpufreq_set_policy() which is called for
scenarios where we don't really want cpufreq_stat_notifier_policy() to get
called. For example whenever we are changing anything related to a policy:
min/max/current freq, etc. cpufreq_set_policy() is called and so cpufreq
stats is notified. Where we don't do any useful stuff other than simply
returning with -EBUSY from cpufreq_stats_create_table(). And so this
isn't the right notifier that cpufreq stats..
Due to all above reasons this patch does following changes:
- Add new notifiers CPUFREQ_CREATE_POLICY and CPUFREQ_REMOVE_POLICY,
which are only called when policy is created/destroyed. They aren't
called for suspend/resume paths..
- Use these notifiers in cpufreq_stat_notifier_policy() to create/destory
stats sysfs entries. And so cpufreq_unregister_driver() or suspend/resume
shouldn't be a problem for cpufreq_stats.
- Return early from cpufreq_stat_cpu_callback() for suspend/resume sequence,
so that we don't free stats structure.
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in freq-table. This also makes cpufreq stats
inconsistent as cpufreq-stats would fail to register because current frequency
of CPU isn't found in freq-table.
Because we don't want this change to affect boot process badly, we go for the
next freq which is >= policy->cur ('cur' must be set by now, otherwise we will
end up setting freq to lowest of the table as 'cur' is initialized to zero).
In case current frequency doesn't match any frequency from freq-table, we throw
warnings to user, so that user can get this fixed in their bootloaders or
freq-tables.
Reported-by: Carlos Hernandez <ceh@ti.com>
Reported-and-tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the current code, if we fail during a frequency transition, we
simply send the POSTCHANGE notification with the old frequency. This
isn't enough.
One of the core users of these notifications is the code responsible
for keeping loops_per_jiffy aligned with frequency changes. And mostly
it is written as:
if ((val == CPUFREQ_PRECHANGE && freq->old < freq->new) ||
(val == CPUFREQ_POSTCHANGE && freq->old > freq->new)) {
update-loops-per-jiffy...
}
So, suppose we are changing to a higher frequency and failed during
transition, then following will happen:
- CPUFREQ_PRECHANGE notification with freq-new > freq-old
- CPUFREQ_POSTCHANGE notification with freq-new == freq-old
The first one will update loops_per_jiffy and second one will do
nothing. Even if we send the 2nd notification by exchanging values of
freq-new and old, some users of these notifications might get
unstable.
This can be fixed by simply calling cpufreq_notify_post_transition()
with error code and this routine will take care of sending
notifications in the correct order.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Folded 3 patches into one, rebased unicore2 changes]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This introduces a new routine cpufreq_notify_post_transition() which
can be used to send POSTCHANGE notification for new freq with or
without both {PRE|POST}CHANGE notifications for last freq. This is
useful at multiple places, especially for sending transition failure
notifications.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When a CPU is hot removed we'll cancel all the delayed work items via
gov_cancel_work(). Sometimes the delayed work function determines that
it should adjust the delay for all other CPUs that the policy is
managing. If this scenario occurs, the canceling CPU will cancel its own
work but queue up the other CPUs works to run.
Commit 3617f2 (cpufreq: Fix timer/workqueue corruption due to double
queueing) has tried to fix this, but reading governor_enabled is not
protected by cpufreq_governor_lock. Even though od_dbs_timer() checks
governor_enabled before gov_queue_work(), this scenario may occur. For
example:
CPU0 CPU1
---- ----
cpu_down()
... <work runs>
__cpufreq_remove_dev() od_dbs_timer()
__cpufreq_governor() policy->governor_enabled
policy->governor_enabled = false;
cpufreq_governor_dbs()
case CPUFREQ_GOV_STOP:
gov_cancel_work(dbs_data, policy);
cpu0 work is canceled
timer is canceled
cpu1 work is canceled
<waits for cpu1>
gov_queue_work(*, *, true);
cpu0 work queued
cpu1 work queued
cpu2 work queued
...
cpu1 work is canceled
cpu2 work is canceled
...
At the end of the GOV_STOP case cpu0 still has a work queued to
run although the code is expecting all of the works to be
canceled. __cpufreq_remove_dev() will then proceed to
re-initialize all the other CPUs works except for the CPU that is
going down. The CPUFREQ_GOV_START case in cpufreq_governor_dbs()
will trample over the queued work and debugobjects will spit out
a warning:
WARNING: at lib/debugobjects.c:260 debug_print_object+0x94/0xbc()
ODEBUG: init active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x14
Modules linked in:
CPU: 1 PID: 1205 Comm: sh Tainted: G W 3.10.0 #200
[<c01144f0>] (unwind_backtrace+0x0/0xf8) from [<c0111d98>] (show_stack+0x10/0x14)
[<c0111d98>] (show_stack+0x10/0x14) from [<c01272cc>] (warn_slowpath_common+0x4c/0x68)
[<c01272cc>] (warn_slowpath_common+0x4c/0x68) from [<c012737c>] (warn_slowpath_fmt+0x30/0x40)
[<c012737c>] (warn_slowpath_fmt+0x30/0x40) from [<c034c640>] (debug_print_object+0x94/0xbc)
[<c034c640>] (debug_print_object+0x94/0xbc) from [<c034c7f8>] (__debug_object_init+0xc8/0x3c0)
[<c034c7f8>] (__debug_object_init+0xc8/0x3c0) from [<c01360e0>] (init_timer_key+0x20/0x104)
[<c01360e0>] (init_timer_key+0x20/0x104) from [<c04872ac>] (cpufreq_governor_dbs+0x1dc/0x68c)
[<c04872ac>] (cpufreq_governor_dbs+0x1dc/0x68c) from [<c04833a8>] (__cpufreq_governor+0x80/0x1b0)
[<c04833a8>] (__cpufreq_governor+0x80/0x1b0) from [<c0483704>] (__cpufreq_remove_dev.isra.12+0x22c/0x380)
[<c0483704>] (__cpufreq_remove_dev.isra.12+0x22c/0x380) from [<c0692f38>] (cpufreq_cpu_callback+0x48/0x5c)
[<c0692f38>] (cpufreq_cpu_callback+0x48/0x5c) from [<c014fb40>] (notifier_call_chain+0x44/0x84)
[<c014fb40>] (notifier_call_chain+0x44/0x84) from [<c012ae44>] (__cpu_notify+0x2c/0x48)
[<c012ae44>] (__cpu_notify+0x2c/0x48) from [<c068dd40>] (_cpu_down+0x80/0x258)
[<c068dd40>] (_cpu_down+0x80/0x258) from [<c068df40>] (cpu_down+0x28/0x3c)
[<c068df40>] (cpu_down+0x28/0x3c) from [<c068e4c0>] (store_online+0x30/0x74)
[<c068e4c0>] (store_online+0x30/0x74) from [<c03a7308>] (dev_attr_store+0x18/0x24)
[<c03a7308>] (dev_attr_store+0x18/0x24) from [<c0256fe0>] (sysfs_write_file+0x100/0x180)
[<c0256fe0>] (sysfs_write_file+0x100/0x180) from [<c01fec9c>] (vfs_write+0xbc/0x184)
[<c01fec9c>] (vfs_write+0xbc/0x184) from [<c01ff034>] (SyS_write+0x40/0x68)
[<c01ff034>] (SyS_write+0x40/0x68) from [<c010e200>] (ret_fast_syscall+0x0/0x48)
In gov_queue_work(), lock cpufreq_governor_lock before gov_queue_work,
and unlock it after __gov_queue_work(). In this way, governor_enabled
is guaranteed not changed in gov_queue_work().
Signed-off-by: Jane Li <jiel@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Prevent __cpufreq_add_dev() from overwriting the existing values of
user_policy.{min|max|policy|governor} with defaults during resume
from system suspend.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If cpufreq_policy_restore() returns NULL during system resume,
__cpufreq_add_dev() should just fall back to the full initialization
instead of returning an error, because that may actually make things
work. Moreover, it should not leave stale fallback data behind after
it has failed to restore a previously existing policy.
This change is based on Viresh Kumar's work.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
When configuring a default governor (via CONFIG_CPU_FREQ_DEFAULT_*) with the
intel_pstate driver, the desired default policy is not properly set. For
example, setting 'CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE' ends up with the
'powersave' policy being set.
Fix by configuring the correct default policy, if either 'powersave' or
'performance' are requested. Otherwise, fallback to what the driver originally
set via its 'init' routine.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are cases where cpufreq_add_dev() may fail for some CPUs
during system resume. With the current code we will still have
sysfs cpufreq files for those CPUs and struct cpufreq_policy
would be already freed for them. Hence any operation on those
sysfs files would result in kernel warnings.
Example of problems resulting from resume errors (from Bjørn Mork):
WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212()
missing sysfs attribute operations for kobject: (null)
Modules linked in: [stripped as irrelevant]
CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006
ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000
ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310
Call Trace:
[<ffffffff81380b0e>] dump_stack+0x55/0x76
[<ffffffff81038635>] warn_slowpath_common+0x7c/0x96
[<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212
[<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43
[<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82
[<ffffffff81182382>] ? sysfs_open_file+0x32/0x212
[<ffffffff811823c7>] sysfs_open_file+0x77/0x212
[<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac
[<ffffffff81122562>] do_dentry_open+0x17c/0x257
[<ffffffff8112267e>] finish_open+0x41/0x4f
[<ffffffff81130225>] do_last+0x80c/0x9ba
[<ffffffff8112dbbd>] ? inode_permission+0x40/0x42
[<ffffffff81130606>] path_openat+0x233/0x4a1
[<ffffffff81130b7e>] do_filp_open+0x35/0x85
[<ffffffff8113b787>] ? __alloc_fd+0x172/0x184
[<ffffffff811232ea>] do_sys_open+0x6b/0xfa
[<ffffffff811233a7>] SyS_openat+0xf/0x11
[<ffffffff8138c812>] system_call_fastpath+0x16/0x1b
To fix this, remove those sysfs files or put the associated kobject
in case of such errors. Also, to make it simple, remove the cpufreq
sysfs links from all the CPUs (except for the policy->cpu) during
suspend, as that operation won't result in a loss of sysfs file
permissions and we can create those links during resume just fine.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-and-tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 2167e2399d (cpufreq: fix garbage kobjects on errors during
suspend/resume) breaks suspend/resume on Martin Ziegler's system
(hard lockup during resume), so revert it.
Fixes: 2167e2399d (cpufreq: fix garbage kobjects on errors during suspend/resume)
References: https://bugzilla.kernel.org/show_bug.cgi?id=66751
Reported-by: Martin Ziegler <ziegler@uni-freiburg.de>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 5a87182aa2 (cpufreq: suspend governors on system
suspend/hibernate) causes hibernation problems to happen on
Bjørn Mork's and Paul Bolle's systems, so revert it.
Fixes: 5a87182aa2 (cpufreq: suspend governors on system suspend/hibernate)
Reported-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is effectively a revert of commit 5302c3fb2e ("cpufreq: Perform
light-weight init/teardown during suspend/resume"), which enabled
suspend/resume optimizations leaving the sysfs files in place.
Errors during suspend/resume are not handled properly, leaving
dead sysfs attributes in case of failures. There are are number of
functions with special code for the "frozen" case, and all these
need to also have special error handling.
The problem is easy to demonstrate by making cpufreq_driver->init()
or cpufreq_driver->get() fail during resume.
The code is too complex for a simple fix, with split code paths
in multiple blocks within a number of functions. It is therefore
best to revert the patch enabling this code until the error handling
is in place.
Examples of problems resulting from resume errors:
WARNING: CPU: 0 PID: 6055 at fs/sysfs/file.c:343 sysfs_open_file+0x77/0x212()
missing sysfs attribute operations for kobject: (null)
Modules linked in: [stripped as irrelevant]
CPU: 0 PID: 6055 Comm: grep Tainted: G D 3.13.0-rc2 #153
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000009 ffff8802327ebb78 ffffffff81380b0e 0000000000000006
ffff8802327ebbc8 ffff8802327ebbb8 ffffffff81038635 0000000000000000
ffffffff811823c7 ffff88021a19e688 ffff88021a19e688 ffff8802302f9310
Call Trace:
[<ffffffff81380b0e>] dump_stack+0x55/0x76
[<ffffffff81038635>] warn_slowpath_common+0x7c/0x96
[<ffffffff811823c7>] ? sysfs_open_file+0x77/0x212
[<ffffffff810386e3>] warn_slowpath_fmt+0x41/0x43
[<ffffffff81182dec>] ? sysfs_get_active+0x6b/0x82
[<ffffffff81182382>] ? sysfs_open_file+0x32/0x212
[<ffffffff811823c7>] sysfs_open_file+0x77/0x212
[<ffffffff81182350>] ? sysfs_schedule_callback+0x1ac/0x1ac
[<ffffffff81122562>] do_dentry_open+0x17c/0x257
[<ffffffff8112267e>] finish_open+0x41/0x4f
[<ffffffff81130225>] do_last+0x80c/0x9ba
[<ffffffff8112dbbd>] ? inode_permission+0x40/0x42
[<ffffffff81130606>] path_openat+0x233/0x4a1
[<ffffffff81130b7e>] do_filp_open+0x35/0x85
[<ffffffff8113b787>] ? __alloc_fd+0x172/0x184
[<ffffffff811232ea>] do_sys_open+0x6b/0xfa
[<ffffffff811233a7>] SyS_openat+0xf/0x11
[<ffffffff8138c812>] system_call_fastpath+0x16/0x1b
The failure to restore cpufreq devices on cancelled hibernation is
not a new bug. It is caused by the ACPI _PPC call failing unless the
hibernate is completed. This makes the acpi_cpufreq driver fail its
init.
Previously, the cpufreq device could be restored by offlining the
cpu temporarily. And as a complete hibernation cycle would do this,
it would be automatically restored most of the time. But after
commit 5302c3fb2e the leftover sysfs attributes will block any
device add action. Therefore offlining and onlining CPU 1 will no
longer restore the cpufreq object, and a complete suspend/resume
cycle will replace it with garbage.
Fixes: 5302c3fb2e ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds cpufreq suspend/resume calls to dpm_{suspend|resume}_noirq()
for handling suspend/resume of cpufreq governors.
Lan Tianyu (Intel) & Jinhyuk Choi (Broadcom) found anr issue where
tunables configuration for clusters/sockets with non-boot CPUs was
getting lost after suspend/resume, as we were notifying governors
with CPUFREQ_GOV_POLICY_EXIT on removal of the last cpu for that
policy and so deallocating memory for tunables. This is fixed by
this patch as we don't allow any operation on governors after
device suspend and before device resume now.
Reported-and-tested-by: Lan Tianyu <tianyu.lan@intel.com>
Reported-by: Jinhyuk Choi <jinchoi@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog, minor cleanups]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the drivers do following in their ->target_index() routines:
struct cpufreq_freqs freqs;
freqs.old = old freq...
freqs.new = new freq...
cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE);
/* Change rate here */
cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE);
This is replicated over all cpufreq drivers today and there doesn't exists a
good enough reason why this shouldn't be moved to cpufreq core instead.
There are few special cases though, like exynos5440, which doesn't do everything
on the call to ->target_index() routine and call some kind of bottom halves for
doing this work, work/tasklet/etc..
They may continue doing notification from their own code as flag:
CPUFREQ_ASYNC_NOTIFICATION is already set for them.
All drivers are also modified in this patch to avoid breaking 'git bisect', as
double notification would happen otherwise.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have per-CPU cpu_policy_rwsem for cpufreq core, but we never use
all of them. We always use rwsem of policy->cpu and so we can
actually make this rwsem per policy instead.
This patch does this change. With this change other tricky situations
are also avoided now, like which lock to take while we are changing
policy->cpu, etc.
Suggested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, the prototype of cpufreq_drivers target routines is:
int target(struct cpufreq_policy *policy, unsigned int target_freq,
unsigned int relation);
And most of the drivers call cpufreq_frequency_table_target() to get a valid
index of their frequency table which is closest to the target_freq. And they
don't use target_freq and relation after that.
So, it makes sense to just do this work in cpufreq core before calling
cpufreq_frequency_table_target() and simply pass index instead. But this can be
done only with drivers which expose their frequency table with cpufreq core. For
others we need to stick with the old prototype of target() until those drivers
are converted to expose frequency tables.
This patch implements the new light weight prototype for target_index() routine.
It looks like this:
int target_index(struct cpufreq_policy *policy, unsigned int index);
CPUFreq core will call cpufreq_frequency_table_target() before calling this
routine and pass index to it. Because CPUFreq core now requires to call routines
present in freq_table.c CONFIG_CPU_FREQ_TABLE must be enabled all the time.
This also marks target() interface as deprecated. So, that new drivers avoid
using it. And Documentation is updated accordingly.
It also converts existing .target() to newly defined light weight
.target_index() routine for many driver.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
The function update_policy_cpu() is expected to be called when the policy->cpu
of a cpufreq policy is to be changed: ie., the new CPU nominated to become the
policy->cpu is different from the old one.
Print a warning if it is invoked with new_cpu == old_cpu, since such an
invocation might hint at a faulty logic in the caller.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CONFIG_CPU_FREQ_TABLE will be always enabled when cpufreq framework is used, as
cpufreq core depends on it. So, we don't need this CONFIG option anymore as it
is not configurable. Remove CONFIG_CPU_FREQ_TABLE and update its users.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many CPUFreq drivers for SMP system (where all cores share same clock lines), do
similar stuff in their ->init() part.
This patch creates a generic routine in cpufreq core which can be used by these
so that we can remove some redundant code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Almost all drivers set policy->cur with current CPU frequency in their ->init()
part. This can be done for all of them at core level and so they wouldn't need
to do it.
This patch adds supporting code in cpufreq core for calling get() after we have
called init() for a policy.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use cpufreq_driver->flags to mark CPUFREQ_HAVE_GOVERNOR_PER_POLICY instead
of a separate field within cpufreq_driver. This will save some bytes of
memory.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Earlier there used to be two functions named __cpufreq_set_policy() and
cpufreq_set_policy(), but now we only have a single routine lets name it
cpufreq_set_policy() instead of __cpufreq_set_policy().
This also removes some invalid comments or fixes some incorrect comments.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Nobody except cpufreq_remove_dev() calls __cpufreq_remove_dev() and
so we don't need two separate routines here. Merge code from
__cpufreq_remove_dev() into cpufreq_remove_dev() and get rid of
__cpufreq_remove_dev().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As a rule its better not to break string (quoted inside "") in a
print statement even if it crosses 80 column boundary as that may
introduce bugs and so this patch rewrites one of the print statements..
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We don't need a blank line just at start of a block, lets remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some section of kerneldoc comment for __cpufreq_remove_dev() is invalid now.
Remove it.
Suggested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
lock_policy_rwsem_{read|write}() currently has return type of int,
but it always returns zero and hence its return type should be void
instead. This patch makes that change and modifies all of the users
accordingly.
Reported-by: Jon Medhurst<tixy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_get() can be called from external drivers which might not be aware if
cpufreq driver is registered or not. And so we should actually check if cpufreq
driver is registered or not and also if cpufreq is active or disabled, at the
beginning of cpufreq_get().
Otherwise call to lock_policy_rwsem_read() might hit BUG_ON(!policy).
Reported-and-tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On systems that support intel_pstate, acpi_cpufreq fails to load, and
udev keeps trying until trace gets filled up and kernel crashes.
The root cause is driver return ret from cpufreq_register_driver(),
because when some other driver takes over before, it will return
EBUSY and then udev will keep trying ...
cpufreq_register_driver() should return EEXIST instead so that the
system can boot without appending intel_pstate=disable and still use
intel_pstate.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Current code looks like this:
WARN_ON(lock_policy_rwsem_write(cpu));
update_policy_cpu(policy, new_cpu);
unlock_policy_rwsem_write(cpu);
{lock|unlock}_policy_rwsem_write(cpu) takes/releases policy->cpu's rwsem.
Because cpu is changing with the call to update_policy_cpu(), the
unlock_policy_rwsem_write() will release the incorrect lock.
The right solution would be to release the same lock as was taken earlier. Also
update_policy_cpu() was also called from cpufreq_add_dev() without any locks and
so its better if we move this locking to inside update_policy_cpu().
This patch fixes a regression introduced in 3.12 by commit f9ba680d23
(cpufreq: Extract the handover of policy cpu to a helper function).
Reported-and-tested-by: Jon Medhurst<tixy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This broke after a recent change "cedb70a cpufreq: Split __cpufreq_remove_dev()
into two parts" from Srivatsa.
Consider a scenario where we have two CPUs in a policy (0 & 1) and we are
removing CPU 1. On the call to __cpufreq_remove_dev_prepare() we have cleared 1
from policy->cpus and now on a call to __cpufreq_remove_dev_finish() we read
cpumask_weight of policy->cpus, which will come as 1 and this code will behave
as if we are removing the last CPU from policy :)
Fix it by clearing the CPU mask in __cpufreq_remove_dev_finish() instead of
__cpufreq_remove_dev_prepare().
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In cpufreq_policy_restore() before system suspend policy is read from
percpu's cpufreq_cpu_data_fallback. It's a read operation rather
than a write one, so take the lock for reading in there.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If update_policy_cpu() is invoked with the existing policy->cpu itself
as the new-cpu parameter, then a lot of things can go terribly wrong.
In its present form, update_policy_cpu() always assumes that the new-cpu
is different from policy->cpu and invokes other functions to perform their
respective updates. And those functions implement the actual update like
this:
per_cpu(..., new_cpu) = per_cpu(..., last_cpu);
per_cpu(..., last_cpu) = NULL;
Thus, when new_cpu == last_cpu, the final NULL assignment makes the per-cpu
references vanish into thin air! (memory leak). From there, it leads to more
problems: cpufreq_stats_create_table() now doesn't find the per-cpu reference
and hence tries to create a new sysfs-group; but sysfs already had created
the group earlier, so it complains that it cannot create a duplicate filename.
In short, the repercussions of a rather innocuous invocation of
update_policy_cpu() can turn out to be pretty nasty.
Ideally update_policy_cpu() should handle this situation (new == last)
gracefully, and not lead to such severe problems. So fix it by adding an
appropriate check.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In __cpufreq_remove_dev_prepare(), the code which decides whether to remove
the sysfs link or nominate a new policy cpu, is governed by an if/else block
with a rather complex set of conditionals. Worse, they harbor a subtlety
which leads to certain unintended behavior.
The code looks like this:
if (cpu != policy->cpu && !frozen) {
sysfs_remove_link(&dev->kobj, "cpufreq");
} else if (cpus > 1) {
new_cpu = cpufreq_nominate_new_policy_cpu(...);
...
update_policy_cpu(..., new_cpu);
}
The original intention was:
If the CPU going offline is not policy->cpu, just remove the link.
On the other hand, if the CPU going offline is the policy->cpu itself,
handover the policy->cpu job to some other surviving CPU in that policy.
But because the 'if' condition also includes the 'frozen' check, now there
are *two* possibilities by which we can enter the 'else' block:
1. cpu == policy->cpu (intended)
2. cpu != policy->cpu && frozen (unintended)
Due to the second (unintended) scenario, we end up spuriously nominating
a CPU as the policy->cpu, even when the existing policy->cpu is alive and
well. This can cause problems further down the line, especially when we end
up nominating the same policy->cpu as the new one (ie., old == new),
because it totally confuses update_policy_cpu().
To avoid this mess, restructure the if/else block to only do what was
originally intended, and thus prevent any unwelcome surprises.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stephen Warren reported that the cpufreq-stats code hits a NULL pointer
dereference during the second attempt to suspend a system. He also
pin-pointed the problem to commit 5302c3f "cpufreq: Perform light-weight
init/teardown during suspend/resume".
That commit actually ensured that the cpufreq-stats table and the
cpufreq-stats sysfs entries are *not* torn down (ie., not freed) during
suspend/resume, which makes it all the more surprising. However, it turns
out that the root-cause is not that we access an already freed memory, but
that the reference to the allocated memory gets moved around and we lose
track of that during resume, leading to the reported crash in a subsequent
suspend attempt.
In the suspend path, during CPU offline, the value of policy->cpu is updated
by choosing one of the surviving CPUs in that policy, as long as there is
atleast one CPU in that policy. And cpufreq_stats_update_policy_cpu() is
invoked to update the reference to the stats structure by assigning it to
the new CPU. However, in the resume path, during CPU online, we end up
assigning a fresh CPU as the policy->cpu, without letting cpufreq-stats
know about this. Thus the reference to the stats structure remains
(incorrectly) associated with the old CPU. So, in a subsequent suspend attempt,
during CPU offline, we end up accessing an incorrect location to get the
stats structure, which eventually leads to the NULL pointer dereference.
Fix this by letting cpufreq-stats know about the update of the policy->cpu
during CPU online in the resume path. (Also, move the update_policy_cpu()
function higher up in the file, so that __cpufreq_add_dev() can invoke
it).
Reported-and-tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 7c30ed5 (cpufreq: make sure frequency transitions are
serialized) attempted to serialize frequency transitions by
adding checks to the CPUFREQ_PRECHANGE and CPUFREQ_POSTCHANGE
notifications. However, it assumed that the notifications will
always originate from the driver's .target() callback, but they
also can be triggered by cpufreq_out_of_sync() and that leads to
warnings like this on some systems:
WARNING: CPU: 0 PID: 14543 at drivers/cpufreq/cpufreq.c:317
__cpufreq_notify_transition+0x238/0x260()
In middle of another frequency transition
accompanied by a call trace similar to this one:
[<ffffffff81720daa>] dump_stack+0x46/0x58
[<ffffffff8106534c>] warn_slowpath_common+0x8c/0xc0
[<ffffffff815b8560>] ? acpi_cpufreq_target+0x320/0x320
[<ffffffff81065436>] warn_slowpath_fmt+0x46/0x50
[<ffffffff815b1ec8>] __cpufreq_notify_transition+0x238/0x260
[<ffffffff815b33be>] cpufreq_notify_transition+0x3e/0x70
[<ffffffff815b345d>] cpufreq_out_of_sync+0x6d/0xb0
[<ffffffff815b370c>] cpufreq_update_policy+0x10c/0x160
[<ffffffff815b3760>] ? cpufreq_update_policy+0x160/0x160
[<ffffffff81413813>] cpufreq_set_cur_state+0x8c/0xb5
[<ffffffff814138df>] processor_set_cur_state+0xa3/0xcf
[<ffffffff8158e13c>] thermal_cdev_update+0x9c/0xb0
[<ffffffff8159046a>] step_wise_throttle+0x5a/0x90
[<ffffffff8158e21f>] handle_thermal_trip+0x4f/0x140
[<ffffffff8158e377>] thermal_zone_device_update+0x57/0xa0
[<ffffffff81415b36>] acpi_thermal_check+0x2e/0x30
[<ffffffff81415ca0>] acpi_thermal_notify+0x40/0xdc
[<ffffffff813e7dbd>] acpi_device_notify+0x19/0x1b
[<ffffffff813f8241>] acpi_ev_notify_dispatch+0x41/0x5c
[<ffffffff813e3fbe>] acpi_os_execute_deferred+0x25/0x32
[<ffffffff81081060>] process_one_work+0x170/0x4a0
[<ffffffff81082121>] worker_thread+0x121/0x390
[<ffffffff81082000>] ? manage_workers.isra.20+0x170/0x170
[<ffffffff81088fe0>] kthread+0xc0/0xd0
[<ffffffff81088f20>] ? flush_kthread_worker+0xb0/0xb0
[<ffffffff8173582c>] ret_from_fork+0x7c/0xb0
[<ffffffff81088f20>] ? flush_kthread_worker+0xb0/0xb0
For this reason, revert commit 7c30ed5 along with the fix 266c13d
(cpufreq: Fix serialization of frequency transitions) on top of it
and we will revisit the serialization problem later.
Reported-by: Alessandro Bono <alessandro.bono@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are places where the variable 'ret' is declared as unsigned int
and then used to store negative return values such as -EINVAL. Fix them
by declaring the variable as a signed quantity.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit "cpufreq: serialize calls to __cpufreq_governor()" had been a temporary
and partial solution to the race condition between writing to a cpufreq sysfs
file and taking a CPU offline. Now that we have a proper and complete solution
to that problem, remove the temporary fix.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The functions that are used to write to cpufreq sysfs files (such as
store_scaling_max_freq()) are not hotplug safe. They can race with CPU
hotplug tasks and lead to problems such as trying to acquire an already
destroyed timer-mutex etc.
Eg:
__cpufreq_remove_dev()
__cpufreq_governor(policy, CPUFREQ_GOV_STOP);
policy->governor->governor(policy, CPUFREQ_GOV_STOP);
cpufreq_governor_dbs()
case CPUFREQ_GOV_STOP:
mutex_destroy(&cpu_cdbs->timer_mutex)
cpu_cdbs->cur_policy = NULL;
<PREEMPT>
store()
__cpufreq_set_policy()
__cpufreq_governor(policy, CPUFREQ_GOV_LIMITS);
policy->governor->governor(policy, CPUFREQ_GOV_LIMITS);
case CPUFREQ_GOV_LIMITS:
mutex_lock(&cpu_cdbs->timer_mutex); <-- Warning (destroyed mutex)
if (policy->max < cpu_cdbs->cur_policy->cur) <- cur_policy == NULL
So use get_online_cpus()/put_online_cpus() in the store_*() functions, to
synchronize with CPU hotplug. However, there is an additional point to note
here: some parts of the CPU teardown in the cpufreq subsystem are done in
the CPU_POST_DEAD stage, with cpu_hotplug.lock *released*. So, using the
get/put_online_cpus() functions alone is insufficient; we should also ensure
that we don't race with those latter steps in the hotplug sequence. We can
easily achieve this by checking if the CPU is online before proceeding with
the store, since the CPU would have been marked offline by the time the
CPU_POST_DEAD notifiers are executed.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_remove_dev_finish() handles the kobject cleanup for a CPU going
offline. But because we destroy the kobject towards the end of the CPU offline
phase, there are certain race windows where a task can try to write to a
cpufreq sysfs file (eg: using store_scaling_max_freq()) while we are taking
that CPU offline, and this can bump up the kobject refcount, which in turn might
hinder the CPU offline task from running to completion. (It can also cause
other more serious problems such as trying to acquire a destroyed timer-mutex
etc., depending on the exact stage of the cleanup at which the task managed to
take a new refcount).
To fix the race window, we will need to synchronize those store_*() call-sites
with CPU hotplug, using get_online_cpus()/put_online_cpus(). However, that
in turn can cause a total deadlock because it can end up waiting for the
CPU offline task to complete, with incremented refcount!
Write to sysfs CPU offline task
-------------- ----------------
kobj_refcnt++
Acquire cpu_hotplug.lock
get_online_cpus();
Wait for kobj_refcnt to drop to zero
**DEADLOCK**
A simple way to avoid this problem is to perform the kobject cleanup in the
CPU offline path, with the cpu_hotplug.lock *released*. That is, we can
perform the wait-for-kobj-refcnt-to-drop as well as the subsequent cleanup
in the CPU_POST_DEAD stage of CPU offline, which is run with cpu_hotplug.lock
released. Doing this helps us avoid deadlocks due to holding kobject refcounts
and waiting on each other on the cpu_hotplug.lock.
(Note: We can't move all of the cpufreq CPU offline steps to the
CPU_POST_DEAD stage, because certain things such as stopping the governors
have to be done before the outgoing CPU is marked offline. So retain those
parts in the CPU_DOWN_PREPARE stage itself).
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During CPU offline, the cpufreq core invokes __cpufreq_remove_dev()
to perform work such as stopping the cpufreq governor, clearing the
CPU from the policy structure etc, and finally cleaning up the
kobject.
There are certain subtle issues related to the kobject cleanup, and
it would be much easier to deal with them if we separate that part
from the rest of the cleanup-work in the CPU offline phase. So split
the __cpufreq_remove_dev() function into 2 parts: one that handles
the kobject cleanup, and the other that handles the rest of the work.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We can't take a big lock around __cpufreq_governor() as this causes
recursive locking for some cases. But calls to this routine must be
serialized for every policy. Otherwise we can see some unpredictable
events.
For example, consider following scenario:
__cpufreq_remove_dev()
__cpufreq_governor(policy, CPUFREQ_GOV_STOP);
policy->governor->governor(policy, CPUFREQ_GOV_STOP);
cpufreq_governor_dbs()
case CPUFREQ_GOV_STOP:
mutex_destroy(&cpu_cdbs->timer_mutex)
cpu_cdbs->cur_policy = NULL;
<PREEMPT>
store()
__cpufreq_set_policy()
__cpufreq_governor(policy, CPUFREQ_GOV_LIMITS);
policy->governor->governor(policy, CPUFREQ_GOV_LIMITS);
case CPUFREQ_GOV_LIMITS:
mutex_lock(&cpu_cdbs->timer_mutex); <-- Warning (destroyed mutex)
if (policy->max < cpu_cdbs->cur_policy->cur) <- cur_policy == NULL
And so store() will eventually result in a crash if cur_policy is
NULL at this point.
Introduce an additional variable which would guarantee serialization
here.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_governor() returns with -EBUSY when governor is already
stopped and we try to stop it again, but when it is stopped we must
not allow calls to CPUFREQ_GOV_LIMITS event as well.
This patch adds this check in __cpufreq_governor().
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To iterate over all policies we currently iterate over all online
CPUs and then get the policy for each of them which is suboptimal.
Use the newly created cpufreq_policy_list for this purpose instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_policy_cpu per-cpu variables are used for storing the ID of
the CPU that manages the given CPU's policy. However, we also store
a policy pointer for each cpu in cpufreq_cpu_data, so the
cpufreq_policy_cpu information is simply redundant.
It is better to use cpufreq_cpu_data to retrieve a policy and get
policy->cpu from there, so make that happen everywhere and drop the
cpufreq_policy_cpu per-cpu variables which aren't necessary any more.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We don't need to check if event is CPUFREQ_GOV_POLICY_INIT and put
governor module as we are sure event can only be START/STOP here.
Remove the useless check.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_policy_list is a list of active policies. We do remove
policies from this list when all CPUs belonging to that policy are
removed. But during system suspend we don't really free a policy
struct as it will be used again during resume, so we didn't remove
it from cpufreq_policy_list as well..
However, this is incorrect. We are saying this policy isn't valid
anymore and must not be referenced (though we haven't freed it), but
it can still be used by code that iterates over cpufreq_policy_list.
Remove policy from this list during system suspend as well.
Of course, we must add it back whenever the first CPU belonging to
that policy shows up.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Align closing brace '}' of an if block.
[rjw: Subject and changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit eb60852 (cpufreq: Use cpufreq_policy_list for iterating
over policies), because it breaks system suspend/resume on multiple
machines.
It either causes resume to block indefinitely or causes the BUG_ON()
in lock_policy_rwsem_##mode() to trigger on sysfs accesses to cpufreq
attributes.
Conflicts:
drivers/cpufreq/cpufreq.c
The __cpufreq_governor() function can fail in rare cases especially
if there are bugs in cpufreq drivers. Thus we must stop processing
as soon as this routine fails, otherwise it may result in undefined
behavior.
This patch adds error checking code whenever this routine is called
from any place.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Critical sections of the cpufreq core are protected with the help of
the driver module owner's refcount, which isn't the correct approach,
because it causes rmmod to return an error when some routine has
updated that refcount.
Let's use rwsem for this purpose instead. Only
cpufreq_unregister_driver() will use write sem
and everybody else will use read sem.
[rjw: Subject & changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq governor owner refcount usage is broken. We should only
increment that refcount when a CPUFREQ_GOV_POLICY_INIT event has come
and it should only be decremented if CPUFREQ_GOV_POLICY_EXIT has come.
Currently, there can be situations where the governor is in use, but
we have allowed it to be unloaded which may result in undefined
behavior. Let's fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To iterate over all policies we currently iterate over all CPUs and
then get the policy for each of them. Let's use the newly created
cpufreq_policy_list for this purpose.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Policies available in the cpufreq framework are now linked together.
They are accessible via cpufreq_policy_list defined in the cpufreq
core.
[rjw: Fix from Yinghai Lu folded in]
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Chapter 14 of Documentation/CodingStyle says:
The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts
readability and introduces an opportunity for a bug when the pointer
variable type is changed but the corresponding sizeof that is passed
to a memory allocator is not.
This wasn't followed consistently in drivers/cpufreq, let's make it
more consistent by always following this rule.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
They are called policy, cur_policy, new_policy, data, etc. Just call
them policy wherever possible.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch addresses the following issues in the header files in the
cpufreq core:
- Include headers in ascending order, so that we don't add same
many times by mistake.
- <asm/> must be included after <linux/>, so that they override
whatever they need to.
- Remove unnecessary includes.
- Don't include files already included by cpufreq.h or
cpufreq_governor.h.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq:
cpufreq: Remove unused function __cpufreq_driver_getavg()
cpufreq: Remove unused APERF/MPERF support
cpufreq: ondemand: Change the calculation of target frequency
The caller of cpufreq_add_policy_cpu() already has a pointer to the
policy structure and there is no need to look it up again in
cpufreq_add_policy_cpu(). Let's pass it directly.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The only case triggering a jump to the err_out_unregister label in
__cpufreq_add_dev() is when cpufreq_add_dev_interface() fails.
However, if cpufreq_add_dev_interface() fails, it calls kobject_put()
for the policy kobject in its error code path and since that causes
the kobject's refcount to become 0, the additional kobject_put() for
the same kobject under err_out_unregister and the
wait_for_completion() following it are pointless, so drop them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The cpufreq core is a little inconsistent in the way it uses the
driver module refcount.
Namely, if __cpufreq_add_dev() is called for a CPU that doesn't
share the policy object with any other CPUs, the driver module
refcount it grabs to start with will be dropped by it before
returning and will be equal to whatever it had been before that
function was invoked.
However, if the given CPU does share the policy object with other
CPUs, either cpufreq_add_policy_cpu() is called to link the new CPU
to the existing policy, or cpufreq_add_dev_symlink() is used to link
the other CPUs sharing the policy with it to the just created policy
object. In that case, because both cpufreq_add_policy_cpu() and
cpufreq_add_dev_symlink() call cpufreq_cpu_get() for the given
policy (the latter possibly many times) without the balancing
cpufreq_cpu_put() (unless there is an error), the driver module
refcount will be left by __cpufreq_add_dev() with a nonzero value
(different from the initial one).
To remove that inconsistency make cpufreq_add_policy_cpu() execute
cpufreq_cpu_put() for the given policy before returning, which
decrements the driver module refcount so that it will be equal to its
initial value after __cpufreq_add_dev() returns. Also remove the
cpufreq_cpu_get() call from cpufreq_add_dev_symlink(), since both the
policy refcount and the driver module refcount are nonzero when it is
called and they don't need to be bumped up by it.
Accordingly, drop the cpufreq_cpu_put() from __cpufreq_remove_dev(),
since it is only necessary to balance the cpufreq_cpu_get() called
by cpufreq_add_policy_cpu() or cpufreq_add_dev_symlink().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Pointer to struct cpufreq_policy is already passed to these routines
and we don't need to send policy->cpu to them as well. So, get rid
of this extra argument and use policy->cpu everywhere.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We call cpufreq_cpu_get() in cpufreq_add_dev_symlink() to increase usage
refcount of policy, but not to get a policy for the given CPU. So, we
don't really need to capture the return value of this routine. We can
simply use policy passed as an argument to cpufreq_add_dev_symlink().
Moreover debug print is rewritten to make it more clear.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we have the infrastructure to perform a light-weight init/tear-down,
use that in the cpufreq CPU hotplug notifier when invoked from the
suspend/resume path.
This also ensures that the file permissions of the cpufreq sysfs files are
preserved across suspend/resume, something which commit a66b2e (cpufreq:
Preserve sysfs files across suspend/resume) originally intended to do, but
had to be reverted due to other problems.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To perform light-weight cpu-init and teardown in the cpufreq subsystem
during suspend/resume, we need to separate out the 2 main functionalities
of the cpufreq CPU hotplug callbacks, as outlined below:
1. Init/tear-down of core cpufreq and CPU-specific components, which are
critical to the correct functioning of the cpufreq subsystem.
2. Init/tear-down of cpufreq sysfs files during suspend/resume.
The first part requires accurate updates to the policy structure such as
its ->cpus and ->related_cpus masks, whereas the second part requires that
the policy->kobj structure is not released or re-initialized during
suspend/resume.
To handle both these requirements, we need to allow updates to the policy
structure throughout suspend/resume, but prevent the structure from getting
freed up. Also, we must have a mechanism by which the cpu-up callbacks can
restore the policy structure, without allocating things afresh. (That also
helps avoid memory leaks).
To achieve this, we use 2 schemes:
a. Use a fallback per-cpu storage area for preserving the policy structures
during suspend, so that they can be restored during resume appropriately.
b. Use the 'frozen' flag to determine when to free or allocate the policy
structure vs when to restore the policy from the saved fallback storage.
Thus we can successfully preserve the structure across suspend/resume.
Effectively, this helps us complete the separation of the 'light-weight'
and the 'full' init/tear-down sequences in the cpufreq subsystem, so that
this can be made use of in the suspend/resume scenario.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During suspend/resume we would like to do a light-weight init/teardown of
CPUs in the cpufreq subsystem and preserve certain things such as sysfs files
etc across suspend/resume transitions. Add a flag called 'frozen' to help
distinguish the full init/teardown sequence from the light-weight one.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
During cpu offline, when the policy->cpu is going down, some other CPU
present in the policy->cpus mask is nominated as the new policy->cpu.
Extract this functionality from __cpufreq_remove_dev() and implement
it in a helper function. This helps in upcoming code reorganization.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_add_dev_interface() includes the work of exposing the interface
to the device, as well as a lot of unrelated stuff. Move the latter to
cpufreq_add_dev(), where it is more appropriate.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Separate out the allocation of the cpufreq policy structure (along with
its error handling) to a helper function. This makes the code easier to
read and also helps with some upcoming code reorganization.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The call to cpufreq_update_policy() is placed in the CPU hotplug callback
of cpufreq_stats, which has a higher priority than the CPU hotplug callback
of cpufreq-core. As a result, during CPU_ONLINE/CPU_ONLINE_FROZEN, we end up
calling cpufreq_update_policy() *before* calling cpufreq_add_dev() !
And for uninitialized CPUs, it just returns silently, not doing anything.
To add to that, cpufreq_stats is not even the right place to call
cpufreq_update_policy() to begin with. The cpufreq core ought to handle
this in its own callback, from an elegance/relevance perspective.
So move the invocation of cpufreq_update_policy() to cpufreq_cpu_callback,
and place it *after* cpufreq_add_dev().
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since cpufreq_cpu_put() called by __cpufreq_remove_dev() drops the
driver module refcount, __cpufreq_remove_dev() causes that refcount
to become negative for the cpufreq driver after a suspend/resume
cycle.
This is not the only bad thing that happens there, however, because
kobject_put() should only be called for the policy kobject at this
point if the CPU is not the last one for that policy.
Namely, if the given CPU is the last one for that policy, the
policy kobject's refcount should be 1 at this point, as set by
cpufreq_add_dev_interface(), and only needs to be dropped once for
the kobject to go away. This actually happens under the cpu == 1
check, so it need not be done before by cpufreq_cpu_put().
On the other hand, if the given CPU is not the last one for that
policy, this means that cpufreq_add_policy_cpu() has been called
at least once for that policy and cpufreq_cpu_get() has been
called for it too. To balance that cpufreq_cpu_get(), we need to
call cpufreq_cpu_put() in that case.
Thus, to fix the described problem and keep the reference
counters balanced in both cases, move the cpufreq_cpu_get() call
in __cpufreq_remove_dev() to the code path executed only for
CPUs that share the policy with other CPUs.
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: 3.10+ <stable@vger.kernel.org>
The target frequency calculation method in the ondemand governor has
changed and it is now independent of the measured average frequency.
Consequently, the __cpufreq_driver_getavg() function and getavg
member of struct cpufreq_driver are not used any more, so drop them.
[rjw: Changelog]
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Two cpufreq commits from the 3.10 cycle introduced regressions.
The first of them was buggy (it did way much more than it needed
to do) and the second one attempted to fix an issue introduced by
the first one. Fixes from Srivatsa S Bhat revert both.
- If autosleep triggers during system shutdown and the shutdown
callbacks of some device drivers have been called already, it may
crash the system. Fix from Liu Shuo prevents that from happening
by making try_to_suspend() check system_state.
- The ACPI memory hotplug driver doesn't clear its driver_data on
errors which may cause a NULL poiter dereference to happen later.
Fix from Toshi Kani.
- The ACPI namespace scanning code should not try to attach scan
handlers to device objects that have them already, which may confuse
things quite a bit, and it should rescan the whole namespace branch
starting at the given node after receiving a bus check notify event
even if the device at that particular node has been discovered
already. Fixes from Rafael J Wysocki.
- New ACPI video blacklist entry for a system whose initial backlight
setting from the BIOS doesn't make sense. From Lan Tianyu.
- Garbage string output avoindance for ACPI PNP from Liu Shuo.
- Two Kconfig fixes for issues introduced recently in the s3c24xx
cpufreq driver (when moving the driver to drivers/cpufreq) from
Paul Bolle.
- Trivial comment fix in pm_wakeup.h from Chanwoo Choi.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJR6Sq+AAoJEKhOf7ml8uNsrGQP/0HRDW+QmTGM8znDTHXngbn9
X3pqlpjEOiCtcmJaSJlD7GwLHMscwWcHKEezteaZ7KUI4mcnysJX6EY5YVbNriDC
xlLcDQn9c6Xx1maCSfp+WMygvqItxZwuc8veRjrT3XtOfCNWS/FlX40Voh63BCAe
GbfQ/HesmUg5CKplyD8/XypLWh5OFXmHzCe8IhrKGfhsZukXdSgSBjwQZMRrEMsQ
kJjDCF8zUu0JisiWqL+xE6IFSKme9i6LBlHpzU0Y1g4RqAqkIbuS0Z3vezOYzoTD
oZjBNa9XAgCS3x0l5g3G0ChgDAU+Mpji/imXA7JysrwbirGFbtPHtQYh2HzpAtnw
Hkah/0ocBM7/w7VTsUQiRsFPdIJTCBLlm6J38x8yh7n84h4nJgOpK69dBLrMwCUZ
f3kid6KIPVLBvnC3QSULrCAKUcUcVVWYtNho+sfXBMjP+cPwTmc3DvATnpru6twa
0KjR5o585UOcciq7EWAoMrCFCfZYF5C4XGaZAxHI/SWooxeCQH84S8vfNLL2epVC
ixmLYo4X2ANDsnfbUV+ewhB0/L2905Et6NhPUgPD/1rm15MEZbowbB2K0pzr0QL9
/1hTL61InXx3jLxducJJFKN+HZ0zfDQdTkyafKrR9jb+GsdmnzYJ/vnfDG8MfPjp
GZ281YBqVmUeYJh5CPU+
=IUmn
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes collected over the last week, most importnatly two
cpufreq reverts fixing regressions introduced in 3.10, an autoseelp
fix preventing systems using it from crashing during shutdown and two
ACPI scan fixes related to hotplug.
Specifics:
- Two cpufreq commits from the 3.10 cycle introduced regressions.
The first of them was buggy (it did way much more than it needed to
do) and the second one attempted to fix an issue introduced by the
first one. Fixes from Srivatsa S Bhat revert both.
- If autosleep triggers during system shutdown and the shutdown
callbacks of some device drivers have been called already, it may
crash the system. Fix from Liu Shuo prevents that from happening
by making try_to_suspend() check system_state.
- The ACPI memory hotplug driver doesn't clear its driver_data on
errors which may cause a NULL poiter dereference to happen later.
Fix from Toshi Kani.
- The ACPI namespace scanning code should not try to attach scan
handlers to device objects that have them already, which may
confuse things quite a bit, and it should rescan the whole
namespace branch starting at the given node after receiving a bus
check notify event even if the device at that particular node has
been discovered already. Fixes from Rafael J Wysocki.
- New ACPI video blacklist entry for a system whose initial backlight
setting from the BIOS doesn't make sense. From Lan Tianyu.
- Garbage string output avoindance for ACPI PNP from Liu Shuo.
- Two Kconfig fixes for issues introduced recently in the s3c24xx
cpufreq driver (when moving the driver to drivers/cpufreq) from
Paul Bolle.
- Trivial comment fix in pm_wakeup.h from Chanwoo Choi"
* tag 'pm+acpi-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: ignore BIOS initial backlight value for Fujitsu E753
PNP / ACPI: avoid garbage in resource name
cpufreq: Revert commit 2f7021a8 to fix CPU hotplug regression
cpufreq: s3c24xx: fix "depends on ARM_S3C24XX" in Kconfig
cpufreq: s3c24xx: rename CONFIG_CPU_FREQ_S3C24XX_DEBUGFS
PM / Sleep: Fix comment typo in pm_wakeup.h
PM / Sleep: avoid 'autosleep' in shutdown progress
cpufreq: Revert commit a66b2e to fix suspend/resume regression
ACPI / memhotplug: Fix a stale pointer in error path
ACPI / scan: Always call acpi_bus_scan() for bus check notifications
ACPI / scan: Do not try to attach scan handlers to devices having them
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
This removes all the drivers/cpufreq uses of the __cpuinit macros
from all C files.
[1] https://lkml.org/lkml/2013/5/20/589
[v2: leave 2nd lines of args misaligned as requested by Viresh]
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: cpufreq@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
commit a66b2e (cpufreq: Preserve sysfs files across suspend/resume)
has unfortunately caused several things in the cpufreq subsystem to
break subtly after a suspend/resume cycle.
The intention of that patch was to retain the file permissions of the
cpufreq related sysfs files across suspend/resume. To achieve that,
the commit completely removed the calls to cpufreq_add_dev() and
__cpufreq_remove_dev() during suspend/resume transitions. But the
problem is that those functions do 2 kinds of things:
1. Low-level initialization/tear-down that are critical to the
correct functioning of cpufreq-core.
2. Kobject and sysfs related initialization/teardown.
Ideally we should have reorganized the code to cleanly separate these
two responsibilities, and skipped only the sysfs related parts during
suspend/resume. Since we skipped the entire callbacks instead (which
also included some CPU and cpufreq-specific critical components),
cpufreq subsystem started behaving erratically after suspend/resume.
So revert the commit to fix the regression. We'll revisit and address
the original goal of that commit separately, since it involves quite a
bit of careful code reorganization and appears to be non-trivial.
(While reverting the commit, note that another commit f51e1eb
(cpufreq: Fix cpufreq regression after suspend/resume) already
reverted part of the original set of changes. So revert only the
remaining ones).
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Paul Bolle <pebolle@tiscali.nl>
Cc: 3.10+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 7c30ed ("cpufreq: make sure frequency transitions are serialized")
interacts poorly with systems that have a single core freqency for all
cores. On such systems we have a single policy for all cores with
several CPUs. When we do a frequency transition the governor calls the
pre and post change notifiers which causes cpufreq_notify_transition()
per CPU. Since the policy is the same for all of them all CPUs after
the first and the warnings added are generated by checking a per-policy
flag the warnings will be triggered for all cores after the first.
Fix this by allowing notifier to be called for n times. Where n is the number of
cpus in policy->cpus.
Reported-and-tested-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commits fcf8058 (cpufreq: Simplify cpufreq_add_dev()) and aa77a52
(cpufreq: acpi-cpufreq: Don't set policy->related_cpus from .init())
changed the contents of the "related_cpus" sysfs attribute on systems
where acpi-cpufreq is used and user space can't get the list of CPUs
which are in the same hardware coordination CPU domain (provided by
the ACPI AML method _PSD) via "related_cpus" any more.
To make up for that loss add a new sysfs attribute "freqdomian_cpus"
for the acpi-cpufreq driver which exposes the list of CPUs in the
same domain regardless of whether it is coordinated by hardware or
software.
[rjw: Changelog, documentation]
References: https://bugzilla.kernel.org/show_bug.cgi?id=58761
Reported-by: Jean-Philippe Halimi <jean-philippe.halimi@exascale-computing.eu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Whenever we are changing frequency of a cpu, we are calling PRECHANGE and
POSTCHANGE notifiers. They must be serialized. i.e. PRECHANGE or POSTCHANGE
shouldn't be called twice contiguously.
This can happen due to bugs in users of __cpufreq_driver_target() or actual
cpufreq drivers who are sending these notifiers.
This patch adds some protection against this. Now, we keep track of the last
transaction and see if something went wrong.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_notify_transition() is used only in cpufreq.c,
make it static.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There were a few noticeable formatting issues in core cpufreq code.
This cleans them up to make code look better. The changes include:
- Whitespace cleanup.
- Rearrangements of code.
- Multiline comments fixes.
- Formatting changes to fit 80 columns.
Copyright information in cpufreq.c is also updated to include my name
for 2013.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cpufreq governors' stop and start operations should be carried out
in sequence. Otherwise, there will be unexpected behavior, like in
the example below.
Suppose there are 4 CPUs and policy->cpu=CPU0, CPU1/2/3 are linked
to CPU0. The normal sequence is:
1) Current governor is userspace. An application tries to set the
governor to ondemand. It will call __cpufreq_set_policy() in
which it will stop the userspace governor and then start the
ondemand governor.
2) Current governor is userspace. The online of CPU3 runs on CPU0.
It will call cpufreq_add_policy_cpu() in which it will first
stop the userspace governor, and then start it again.
If the sequence of the above two cases interleaves, it becomes:
1) Application stops userspace governor
2) Hotplug stops userspace governor
which is a problem, because the governor shouldn't be stopped twice
in a row. What happens next is:
3) Application starts ondemand governor
4) Hotplug starts a governor
In step 4, the hotplug is supposed to start the userspace governor,
but now the governor has been changed by the application to ondemand,
so the ondemand governor is started once again, which is incorrect.
The solution is to prevent policy governors from being stopped
multiple times in a row. A governor should only be stopped once for
one policy. After it has been stopped, no more governor stop
operations should be executed.
Also add a mutex to serialize governor operations.
[rjw: Changelog. And you owe me a beverage of my choice.]
Signed-off-by: Xiaoguang Chen <chenxg@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
struct cpufreq_policy is already passed as argument to some routines
like: __cpufreq_driver_getavg() and so we don't really need to do
cpufreq_cpu_get() before and cpufreq_cpu_put() in them to get a
policy structure.
Remove them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When we don't have any file in cpu/cpufreq directory we shouldn't
create it. Specially with the introduction of per-policy governor
instance patchset, even governors are moved to
cpu/cpu*/cpufreq/governor-name directory and so this directory is
just not required.
Lets have it only when required.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Governors other than ondemand and conservative can also use
get_cpu_idle_time() and they aren't required to compile
cpufreq_governor.c. So, move these independent routines to
cpufreq.c instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
get_governor_parent_kobj() can be used by any governor, generic
cpufreq governors or platform specific ones and so must be present in
cpufreq.c instead of cpufreq_governor.c.
This patch moves it to cpufreq.c. This also adds
EXPORT_SYMBOL_GPL(get_governor_parent_kobj) so that modules can use
this function too.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds: EXPORT_SYMBOL_GPL(have_governor_per_policy), so that
this routine can be used by modules too.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The file permissions of cpufreq per-cpu sysfs files are not preserved
across suspend/resume because we internally go through the CPU
Hotplug path which reinitializes the file permissions on CPU online.
But the user is not supposed to know that we are using CPU hotplug
internally within suspend/resume (IOW, the kernel should not silently
wreck the user-set file permissions across a suspend cycle).
Therefore, we need to preserve the file permissions as they are
across suspend/resume.
The simplest way to achieve that is to just not touch the sysfs files
at all - ie., just ignore the CPU hotplug notifications in the
suspend/resume path (_FROZEN) in the cpufreq hotplug callback.
Reported-by: Robert Jarzmik <robert.jarzmik@intel.com>
Reported-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We must call __cpufreq_governor(data, CPUFREQ_GOV_POLICY_EXIT) before
calling cpufreq_cpu_put(data), so that policy kobject have valid
fields. Otherwise, removing last online cpu of policy->cpus causes
this crash for ondemand/conservative governor.
[<c00fb076>] (sysfs_find_dirent+0xe/0xa8) from [<c00fb1bd>] (sysfs_get_dirent+0x21/0x58)
[<c00fb1bd>] (sysfs_get_dirent+0x21/0x58) from [<c00fc259>] (sysfs_remove_group+0x85/0xbc)
[<c00fc259>] (sysfs_remove_group+0x85/0xbc) from [<c02faad9>] (cpufreq_governor_dbs+0x369/0x4a0)
[<c02faad9>] (cpufreq_governor_dbs+0x369/0x4a0) from [<c02f66d7>] (__cpufreq_governor+0x2b/0x8c)
[<c02f66d7>] (__cpufreq_governor+0x2b/0x8c) from [<c02f6893>] (__cpufreq_remove_dev.isra.12+0x15b/0x250)
[<c02f6893>] (__cpufreq_remove_dev.isra.12+0x15b/0x250) from [<c03e91c7>] (cpufreq_cpu_callback+0x2f/0x3c)
[<c03e91c7>] (cpufreq_cpu_callback+0x2f/0x3c) from [<c0036fe1>] (notifier_call_chain+0x45/0x54)
[<c0036fe1>] (notifier_call_chain+0x45/0x54) from [<c001e611>] (__cpu_notify+0x1d/0x34)
[<c001e611>] (__cpu_notify+0x1d/0x34) from [<c03e5833>] (_cpu_down+0x63/0x1ac)
[<c03e5833>] (_cpu_down+0x63/0x1ac) from [<c03e5997>] (cpu_down+0x1b/0x30)
[<c03e5997>] (cpu_down+0x1b/0x30) from [<c03e60eb>] (store_online+0x27/0x54)
[<c03e60eb>] (store_online+0x27/0x54) from [<c0295629>] (dev_attr_store+0x11/0x18)
[<c0295629>] (dev_attr_store+0x11/0x18) from [<c00f9edd>] (sysfs_write_file+0xed/0x114)
[<c00f9edd>] (sysfs_write_file+0xed/0x114) from [<c00b42a9>] (vfs_write+0x65/0xd8)
[<c00b42a9>] (vfs_write+0x65/0xd8) from [<c00b4523>] (sys_write+0x2f/0x50)
[<c00b4523>] (sys_write+0x2f/0x50) from [<c000cdc1>] (ret_fast_syscall+0x1/0x52)
Of course this only impacted drivers which have
have_governor_per_policy set to true. i.e. big LITTLE cpufreq driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 5800043 (cpufreq: convert cpufreq_driver to using RCU) causes
the following call trace to be spit on boot:
BUG: sleeping function called from invalid context at /scratch/rafael/work/linux-pm/mm/slab.c:3179
in_atomic(): 0, irqs_disabled(): 0, pid: 292, name: systemd-udevd
2 locks held by systemd-udevd/292:
#0: (subsys mutex){+.+.+.}, at: [<ffffffff8146851a>] subsys_interface_register+0x4a/0xe0
#1: (rcu_read_lock){.+.+.+}, at: [<ffffffff81538210>] cpufreq_add_dev_interface+0x60/0x5e0
Pid: 292, comm: systemd-udevd Not tainted 3.9.0-rc8+ #323
Call Trace:
[<ffffffff81072c90>] __might_sleep+0x140/0x1f0
[<ffffffff811581c2>] kmem_cache_alloc+0x42/0x2b0
[<ffffffff811e7179>] sysfs_new_dirent+0x59/0x130
[<ffffffff811e63cb>] sysfs_add_file_mode+0x6b/0x110
[<ffffffff81538210>] ? cpufreq_add_dev_interface+0x60/0x5e0
[<ffffffff810a3254>] ? __lock_is_held+0x54/0x80
[<ffffffff811e647d>] sysfs_add_file+0xd/0x10
[<ffffffff811e6541>] sysfs_create_file+0x21/0x30
[<ffffffff81538280>] cpufreq_add_dev_interface+0xd0/0x5e0
[<ffffffff81538210>] ? cpufreq_add_dev_interface+0x60/0x5e0
[<ffffffffa000337f>] ? acpi_processor_get_platform_limit+0x32/0xbb [processor]
[<ffffffffa022f540>] ? do_drv_write+0x70/0x70 [acpi_cpufreq]
[<ffffffff810a3254>] ? __lock_is_held+0x54/0x80
[<ffffffff8106c97e>] ? up_read+0x1e/0x40
[<ffffffff8106e632>] ? __blocking_notifier_call_chain+0x72/0xc0
[<ffffffff81538dbd>] cpufreq_add_dev+0x62d/0xae0
[<ffffffff815389b8>] ? cpufreq_add_dev+0x228/0xae0
[<ffffffff81468569>] subsys_interface_register+0x99/0xe0
[<ffffffffa014d000>] ? 0xffffffffa014cfff
[<ffffffff81535d5d>] cpufreq_register_driver+0x9d/0x200
[<ffffffffa014d000>] ? 0xffffffffa014cfff
[<ffffffffa014d0e9>] acpi_cpufreq_init+0xe9/0x1000 [acpi_cpufreq]
[<ffffffff810002fa>] do_one_initcall+0x11a/0x170
[<ffffffff810b4b87>] load_module+0x1cf7/0x2920
[<ffffffff81322580>] ? ddebug_proc_open+0xb0/0xb0
[<ffffffff816baee0>] ? retint_restore_args+0xe/0xe
[<ffffffff810b5887>] sys_init_module+0xd7/0x120
[<ffffffff816bb6d2>] system_call_fastpath+0x16/0x1b
which is quite obvious, because that commit put (multiple instances
of) sysfs_create_file() under rcu_read_lock()/rcu_read_unlock(),
although sysfs_create_file() may cause memory to be allocated with
GFP_KERNEL and that may sleep, which is not permitted in RCU read
critical section.
Revert the buggy commit altogether along with some changes on top
of it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some cpufreq drivers implement their own governor and so don't need
us to call generic governors interface via __cpufreq_governor(). Few
recent commits haven't obeyed this law well and we saw some
regressions.
This patch is an attempt to fix the above issue.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Tested-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_governor() must be called with a correct policy->cpus mask.
In __cpufreq_remove_dev() we initially clear policy->cpus with
cpumask_clear_cpu() and then call
__cpufreq_governor(policy, CPUFREQ_GOV_POLICY_EXIT). If the governor
is doing some per-cpu stuff in EXIT callback, this can create
uncertain behavior.
Generic governors in drivers/cpufreq/ doesn't do any per-cpu stuff
in EXIT callback and so we don't face any issues currently. But its
better to keep the code clean, so we don't face any issues in future.
Now, we call cpumask_clear_cpu() only when multiple cpus are managed
by policy.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We eventually would like to remove the rwlock cpufreq_driver_lock or
convert it back to a spinlock and protect the read sections with RCU.
The first step in that direction is to make cpufreq_driver use RCU.
I don't see an easy wasy to protect the cpufreq_cpu_data structure
with RCU, so I am leaving it with the rwlock for now since under
certain configs __cpufreq_cpu_get is a hot spot with 256+ cores.
[rjw: Subject, changelog, white space]
Signed-off-by: Nathan Zimmer <nzimmer@sgi.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->cpus contains all online cpus that have single shared clock line. And
their frequencies are always updated together.
Many SMP system's cpufreq drivers take care of this in individual drivers but
the best place for this code is in cpufreq core.
This patch modifies cpufreq_notify_transition() to notify frequency change for
all cpus in policy->cpus and hence updates all users of this API.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, there can't be multiple instances of single governor_type.
If we have a multi-package system, where we have multiple instances
of struct policy (per package), we can't have multiple instances of
same governor. i.e. We can't have multiple instances of ondemand
governor for multiple packages.
Governors directory in sysfs is created at /sys/devices/system/cpu/cpufreq/
governor-name/. Which again reflects that there can be only one
instance of a governor_type in the system.
This is a bottleneck for multicluster system, where we want different
packages to use same governor type, but with different tunables.
This patch uses the infrastructure provided by earlier patch and
implements init/exit routines for ondemand and conservative
governors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, there can't be multiple instances of single governor_type.
If we have a multi-package system, where we have multiple instances
of struct policy (per package), we can't have multiple instances of
same governor. i.e. We can't have multiple instances of ondemand
governor for multiple packages.
Governors directory in sysfs is created at /sys/devices/system/cpu/cpufreq/
governor-name/. Which again reflects that there can be only one
instance of a governor_type in the system.
This is a bottleneck for multicluster system, where we want different
packages to use same governor type, but with different tunables.
This patch is inclined towards providing this infrastructure. Because
we are required to allocate governor's resources dynamically now, we
must do it at policy creation and end. And so got
CPUFREQ_GOV_POLICY_INIT/EXIT.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This eliminates the contention I am seeing in __cpufreq_cpu_get.
It also nicely stages the lock to be replaced by the rcu.
Signed-off-by: Nathan Zimmer <nzimmer@sgi.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq: (55 commits)
cpufreq / intel_pstate: Fix 32 bit build
cpufreq: conservative: Fix typos in comments
cpufreq: ondemand: Fix typos in comments
cpufreq: exynos: simplify .init() for setting policy->cpus
cpufreq: kirkwood: Add a cpufreq driver for Marvell Kirkwood SoCs
cpufreq/x86: Add P-state driver for sandy bridge.
cpufreq_stats: do not remove sysfs files if frequency table is not present
cpufreq: Do not track governor name for scaling drivers with internal governors.
cpufreq: Only call cpufreq_out_of_sync() for driver that implement cpufreq_driver.target()
cpufreq: Retrieve current frequency from scaling drivers with internal governors
cpufreq: Fix locking issues
cpufreq: Create a macro for unlock_policy_rwsem{read,write}
cpufreq: Remove unused HOTPLUG_CPU code
cpufreq: governors: Fix WARN_ON() for multi-policy platforms
cpufreq: ondemand: Replace down_differential tuner with adj_up_threshold
cpufreq / stats: Get rid of CPUFREQ_STATDEVICE_ATTR
cpufreq: Don't check cpu_online(policy->cpu)
cpufreq: add imx6q-cpufreq driver
cpufreq: Don't remove sysfs link for policy->cpu
cpufreq: Remove unnecessary use of policy->shared_type
...
Scaling drivers that implement internal governors do not have governor
structures assocaited with them. Only track the name of the governor
associated with the CPU if the driver does not implement
cpufreq_driver.setpolicy()
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Scaling drivers that implement cpufreq_driver.setpolicy() have
internal governors that do not signal changes via
cpufreq_notify_transition() so the frequncy in the policy will almost
certainly be different than the current frequncy. Only call
cpufreq_out_of_sync() when the underlying driver implements
cpufreq_driver.target()
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Scaling drivers that implement the cpufreq_driver.setpolicy() versus
the cpufreq_driver.target() interface do not set policy->cur.
Normally policy->cur is set during the call to cpufreq_driver.target()
when the frequnecy request is made by the governor.
If the scaling driver implements cpufreq_driver.setpolicy() and
cpufreq_driver.get() interfaces use cpufreq_driver.get() to retrieve
the current frequency.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq core uses two locks:
- cpufreq_driver_lock: General lock for driver and cpufreq_cpu_data array.
- cpu_policy_rwsemfix locking: per CPU reader-writer semaphore designed to cure
all cpufreq/hotplug/workqueue/etc related lock issues.
These locks were not used properly and are placed against their principle
(present before their definition) at various places. This patch is an attempt to
fix their use.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On the lines of macro: lock_policy_rwsem, we can create another macro for
unlock_policy_rwsem. Lets do it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because the sibling cpu of any online cpu is identified very early in
cpufreq_add_dev(), below code is never executed. And so can be removed.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On multi-policy systems there is a single instance of governor for both the
policies (if same governor is chosen for both policies). With the code update
from following patches:
8eeed09 cpufreq: governors: Get rid of dbs_data->enable field
b394058 cpufreq: governors: Reset tunables only for cpufreq_unregister_governor()
We are creating/removing sysfs directory of governor for for every call to
GOV_START and STOP. This would fail for multi-policy system as there is a
per-policy call to START/STOP.
This patch reuses the governor->initialized variable to detect total users of
governor.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->cpu or cpus in policy->cpus can't be offline anymore. And so we don't
need to check if they are online or not.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
"cpufreq" directory in policy->cpu is never created using
sysfs_create_link(), but using kobject_init_and_add(). And so we
shouldn't call sysfs_remove_link() for policy->cpu(). sysfs stuff
for policy->cpu is automatically removed when we call kobject_put()
for dying policy.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, whenever governor->governor() is called for CPUFRREQ_GOV_START event
we reset few tunables of governor. Which isn't correct, as this routine is
called for every cpu hot-[un]plugging event. We should actually be resetting
these only when the governor module is removed and re-installed.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently cpufreq_add_dev() firsts allocates policy, calls
driver->init() and then checks if this CPU is already managed or not.
And if it is already managed, its policy is freed.
We can save all this if we somehow know that CPU is managed or not in
advance. policy->related_cpus contains the list of all valid sibling
CPUs of policy->cpu. We can check this to see if the current CPU is
already managed.
From now on, platforms don't really need to set related_cpus from
their init() routines, as the same work is done by core too.
If a platform driver needs to set the related_cpus mask with some
additional CPUs, other than CPUs present in policy->cpus, they are
free to do it, though, as we don't override anything.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 956f339 "cpufreq: Don't use cpu removed during
cpufreq_driver_unregister".
With the addition of the following commit, this change/variable is not
required any more:
commit b9ba2725343ae57add3f324dfa5074167f48de96
Author: Viresh Kumar <viresh.kumar@linaro.org>
Date: Mon Jan 14 13:23:03 2013 +0000
cpufreq: Simplify __cpufreq_remove_dev()
[rjw: Subject and changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a helper function to return cpufreq_driver->name.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When disable_cpufreq() is called some exported functions are still
being used that do not have a check for cpufreq being disabled.
Add a disabled check into cpufreq_cpu_get() to return NULL if
cpufreq is disabled this covers most of the exported functions. For
the exported functions that do not call cpufreq_cpu_get() add an
explicit check.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_remove_dev() is called on multiple occasions: cpufreq_driver
unregister and cpu removals.
Current implementation of this routine is overly complex without much need. If
the cpu to be removed is the policy->cpu, we remove the policy first and add all
other cpus again from policy->cpus and then finally call __cpufreq_remove_dev()
again to remove the cpu to be deleted. Haahhhh..
There exist a simple solution to removal of a cpu:
- Simply use the old policy structure
- update its fields like: policy->cpu, etc.
- notify any users of cpufreq, which depend on changing policy->cpu
Hence this patch, which tries to implement the above theory. It is tested well
by myself on ARM big.LITTLE TC2 SoC, which has 5 cores (2 A15 and 3 A7). Both
A15's share same struct policy and all A7's share same policy structure.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is how the core works:
cpufreq_driver_unregister()
- subsys_interface_unregister()
- for_each_cpu() call cpufreq_remove_dev(), i.e. 0,1,2,3,4 when we
unregister.
cpufreq_remove_dev():
- Remove policy node
- Call cpufreq_add_dev() for next cpu, sharing mask with removed cpu.
i.e. When cpu 0 is removed, we call it for cpu 1. And when called for cpu 2,
we call it for cpu 3.
- cpufreq_add_dev() would call cpufreq_driver->init()
- init would return mask as AND of 2, 3 and 4 for cluster A7.
- cpufreq core would do online_cpu && policy->cpus
Here is the BUG(). Because cpu hasn't died but we have just unregistered
the cpufreq driver, online cpu would still have cpu 2 in it. And so thing
go bad again.
Solution: Keep cpumask of cpus that are registered with cpufreq core and clear
cpus when we get a call from subsys_interface_unregister() via
cpufreq_remove_dev().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because cpufreq core and governors worry only about the online cpus, if a cpu is
hot [un]plugged, we must notify governors about it, otherwise be ready to expect
something unexpected.
We already have notifiers in the form of CPUFREQ_GOV_START/CPUFREQ_GOV_STOP, we
just need to call them now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq core doesn't manage offline cpus and if driver->init() has returned
mask including offline cpus, it may result in unwanted behavior by cpufreq core
or governors.
We need to get only online cpus in this mask. There are two places to fix this
mask, cpufreq core and cpufreq driver. It makes sense to do this at common place
and hence is done in core.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The text in Documentation said it would be removed in 2.6.41;
the text in the Kconfig said removal in the 3.1 release. Either
way you look at it, we are well past both, so push it off a cliff.
Note that the POWER_CSTATE and the POWER_PSTATE are part of the
legacy tracing API. Remove all tracepoints which use these flags.
As can be seen from context, most already have a trace entry via
trace_cpu_idle anyways.
Also, the cpufreq/cpufreq.c PSTATE one is actually unpaired, as
compared to the CSTATE ones which all have a clear start/stop.
As part of this, the trace_power_frequency also becomes orphaned,
so it too is deleted.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove an unnecessary initializer for the 'ret' variable in
__cpufreq_set_policy().
[rjw: Modified the subject and changelog slightly.]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_driver_target() must not pass target frequency beyond the
limits of current policy.
Today most of cpufreq platform drivers are doing this check in their
target routines. Why not move it to __cpufreq_driver_target()?
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Avoid calling cpufreq driver's target() routine if new frequency is same as
policies current frequency.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_disabled() is a local function, so should be marked static.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need to do cpufreq_get_cpu() and cpufreq_put_cpu() for drivers that
don't support getavg() routine.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With debug options on, it is difficult to locate cpufreq core's debug prints.
Fix this by prefixing debug prints with KBUILD_MODNAME.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Arrays for governer and driver name are of size CPUFREQ_NAME_LEN or 16.
i.e. 15 bytes for name and 1 for trailing '\0'.
When cpufreq driver print these names (for sysfs), it includes '\n' or ' ' in
the fmt string and still passes length as CPUFREQ_NAME_LEN. If the driver or
governor names are using all 15 fields allocated to them, then the trailing '\n'
or ' ' will never be printed. And so commands like:
root@linaro-developer# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_driver
will print something like:
cpufreq_foodrvroot@linaro-developer#
Fix this by increasing print length by one character.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
show_bios_limit is mistakenly written as show_scaling_driver in a comment
describing purpose of show_bios_limit() routine.
Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Running one program that continuously hotplugs and replugs a cpu
concurrently with another program that continuously writes to the
scaling_setspeed node eventually deadlocks with:
=============================================
[ INFO: possible recursive locking detected ]
3.4.0 #37 Tainted: G W
---------------------------------------------
filemonkey/122 is trying to acquire lock:
(s_active#13){++++.+}, at: [<c01a3d28>] sysfs_remove_dir+0x9c/0xb4
but task is already holding lock:
(s_active#13){++++.+}, at: [<c01a22f0>] sysfs_write_file+0xe8/0x140
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(s_active#13);
lock(s_active#13);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by filemonkey/122:
#0: (&buffer->mutex){+.+.+.}, at: [<c01a2230>] sysfs_write_file+0x28/0x140
#1: (s_active#13){++++.+}, at: [<c01a22f0>] sysfs_write_file+0xe8/0x140
stack backtrace:
[<c0014fcc>] (unwind_backtrace+0x0/0x120) from [<c00ca600>] (validate_chain+0x6f8/0x1054)
[<c00ca600>] (validate_chain+0x6f8/0x1054) from [<c00cb778>] (__lock_acquire+0x81c/0x8d8)
[<c00cb778>] (__lock_acquire+0x81c/0x8d8) from [<c00cb9c0>] (lock_acquire+0x18c/0x1e8)
[<c00cb9c0>] (lock_acquire+0x18c/0x1e8) from [<c01a3ba8>] (sysfs_addrm_finish+0xd0/0x180)
[<c01a3ba8>] (sysfs_addrm_finish+0xd0/0x180) from [<c01a3d28>] (sysfs_remove_dir+0x9c/0xb4)
[<c01a3d28>] (sysfs_remove_dir+0x9c/0xb4) from [<c02d0e5c>] (kobject_del+0x10/0x38)
[<c02d0e5c>] (kobject_del+0x10/0x38) from [<c02d0f74>] (kobject_release+0xf0/0x194)
[<c02d0f74>] (kobject_release+0xf0/0x194) from [<c0565a98>] (cpufreq_cpu_put+0xc/0x24)
[<c0565a98>] (cpufreq_cpu_put+0xc/0x24) from [<c05683f0>] (store+0x6c/0x74)
[<c05683f0>] (store+0x6c/0x74) from [<c01a2314>] (sysfs_write_file+0x10c/0x140)
[<c01a2314>] (sysfs_write_file+0x10c/0x140) from [<c014af44>] (vfs_write+0xb0/0x128)
[<c014af44>] (vfs_write+0xb0/0x128) from [<c014b06c>] (sys_write+0x3c/0x68)
[<c014b06c>] (sys_write+0x3c/0x68) from [<c000e0e0>] (ret_fast_syscall+0x0/0x3c)
This is because store() in cpufreq.c indirectly calls
kobject_get() via cpufreq_cpu_get() and is the last one to call
kobject_put() via cpufreq_cpu_put(). Sysfs code should not call
kobject_get() or kobject_put() directly (see the comment around
sysfs_schedule_callback() for more information).
Fix this deadlock by introducing two new functions:
struct cpufreq_policy *cpufreq_cpu_get_sysfs(unsigned int cpu)
void cpufreq_cpu_put_sysfs(struct cpufreq_policy *data)
which do the same thing as cpufreq_cpu_{get,put}() but don't call
kobject functions.
To easily trigger this deadlock you can insert an msleep() with a
reasonably large value right after the fail label at the bottom
of the store() function in cpufreq.c and then write
scaling_setspeed in one task and offline the cpu in another. The
first task will hang and be detected by the hung task detector.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
useful for disabling cpufreq altogether. The cpu frequency
scaling drivers and cpu frequency governors will fail to register.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: (23 commits)
[CPUFREQ] EXYNOS: Removed useless headers and codes
[CPUFREQ] EXYNOS: Make EXYNOS common cpufreq driver
[CPUFREQ] powernow-k8: Update copyright, maintainer and documentation information
[CPUFREQ] powernow-k8: Fix indexing issue
[CPUFREQ] powernow-k8: Avoid Pstate MSR accesses on systems supporting CPB
[CPUFREQ] update lpj only if frequency has changed
[CPUFREQ] cpufreq:userspace: fix cpu_cur_freq updation
[CPUFREQ] Remove wall variable from cpufreq_gov_dbs_init()
[CPUFREQ] EXYNOS4210: cpufreq code is changed for stable working
[CPUFREQ] EXYNOS4210: Update frequency table for cpu divider
[CPUFREQ] EXYNOS4210: Remove code about bus on cpufreq
[CPUFREQ] s3c64xx: Use pr_fmt() for consistent log messages
cpufreq: OMAP: fixup for omap_device changes, include <linux/module.h>
cpufreq: OMAP: fix freq_table leak
cpufreq: OMAP: put clk if cpu_init failed
cpufreq: OMAP: only supports OPP library
cpufreq: OMAP: dont support !freq_table
cpufreq: OMAP: deny initialization if no mpudev
cpufreq: OMAP: move clk name decision to init
cpufreq: OMAP: notify even with bad boot frequency
...
During scaling up of cpu frequency, loops_per_jiffy
is updated upon invoking PRECHANGE notifier.
If setting to new frequency fails in cpufreq driver,
lpj is left at incorrect value.
Hence update lpj only if cpu frequency is changed,
i.e. upon invoking POSTCHANGE notifier.
Penalty would be that during time period between
changing cpu frequency & invocation of POSTCHANGE
notifier, udelay(x) may not gurantee minimal delay
of 'x' us for frequency scaling up operation.
Perhaps a better solution would be to define
CPUFREQ_ABORTCHANGE & handle accordingly, but then
it would be more intrusive (using ABORTCHANGE may
help drivers also; if any has registered notifier
and expect POST for a PRECHANGE, their needs can
be taken care using ABORT)
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This moves the 'cpu sysdev_class' over to a regular 'cpu' subsystem
and converts the devices to regular devices. The sysdev drivers are
implemented as subsystem interfaces now.
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Userspace relies on events and generic sysfs subsystem infrastructure
from sysdev devices, which are made available with this conversion.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Len Brown <lenb@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows drivers and other code to get the max reported CPU frequency.
Initial use is for scaling ring frequency with GPU frequency in the i915
driver.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Since format string handling is part of request_module, there is no
need to construct the module name. As such, drop the redundant sprintf
and heap usage.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: Dave Jones <davej@redhat.com>
With dynamic debug having gained the capability to report debug messages
also during the boot process, it offers a far superior interface for
debug messages than the custom cpufreq infrastructure. As a first step,
remove the old cpufreq_debug_printk() function and replace it with a call
to the generic pr_debug() function.
How can dynamic debug be used on cpufreq? You need a kernel which has
CONFIG_DYNAMIC_DEBUG enabled.
To enabled debugging during runtime, mount debugfs and
$ echo -n 'module cpufreq +p' > /sys/kernel/debug/dynamic_debug/control
for debugging the complete "cpufreq" module. To achieve the same goal during
boot, append
ddebug_query="module cpufreq +p"
as a boot parameter to the kernel of your choice.
For more detailled instructions, please see
Documentation/dynamic-debug-howto.txt
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
When we discover CPUs that are affected by each other's
frequency/voltage transitions, the first CPU gets a sysfs directory
created, and rest of the siblings get symlinks. Currently, when we
hotplug off only the first CPU, all of the symlinks and the sysfs
directory gets removed. Even though rest of the siblings are still
online and functional, they are orphaned, and no longer governed by
cpufreq.
This patch, given the above scenario, creates a sysfs directory for
the first sibling and symlinks for the rest of the siblings.
Please note the recursive call, it was rather too ugly to roll it
out. And the removal of redundant NULL setting (it is already taken
care of near the top of the function).
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: stable@kernel.org
The cpufreq subsystem uses sysdev suspend and resume for
executing cpufreq_suspend() and cpufreq_resume(), respectively,
during system suspend, after interrupts have been switched off on the
boot CPU, and during system resume, while interrupts are still off on
the boot CPU. In both cases the other CPUs are off-line at the
relevant point (either they have been switched off via CPU hotplug
during suspend, or they haven't been switched on yet during resume).
For this reason, although it may seem that cpufreq_suspend() and
cpufreq_resume() are executed for all CPUs in the system, they are
only called for the boot CPU in fact, which is quite confusing.
To remove the confusion and to prepare for elimiating sysdev
suspend and resume operations from the kernel enirely, convernt
cpufreq to using a struct syscore_ops object for the boot CPU
suspend and resume and rename the callbacks so that their names
reflect their purpose. In addition, put some explanatory remarks
into their kerneldoc comments.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
None of the existing cpufreq drivers uses the second argument of
its .suspend() callback (which isn't useful anyway), so remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
cpufreq_register_driver sets cpufreq_driver to a structure owned (and
placed) in the caller's memory. If cpufreq policy fails in its ->init
function, sysdev_driver_register returns nonzero in
cpufreq_register_driver. Now, cpufreq_register_driver returns an error
without setting cpufreq_driver back to NULL.
Usually cpufreq policy modules are unloaded because they propagate the
error to the module init function and return that.
So a later access to any member of cpufreq_driver causes bugs like:
BUG: unable to handle kernel paging request at ffffffffa00270a0
IP: [<ffffffff8145eca3>] cpufreq_cpu_get+0x53/0xe0
PGD 1805067 PUD 1809063 PMD 1c3f90067 PTE 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/virtual/net/tun0/statistics/collisions
CPU 0
Modules linked in: ...
Pid: 5677, comm: thunderbird-bin Tainted: G W 2.6.38-rc4-mm1_64+ #1389 To be filled by O.E.M./To Be Filled By O.E.M.
RIP: 0010:[<ffffffff8145eca3>] [<ffffffff8145eca3>] cpufreq_cpu_get+0x53/0xe0
RSP: 0018:ffff8801aec37d98 EFLAGS: 00010086
RAX: 0000000000000202 RBX: 0000000000000000 RCX: 0000000000000001
RDX: ffffffffa00270a0 RSI: 0000000000001000 RDI: ffffffff8199ece8
...
Call Trace:
[<ffffffff8145f490>] cpufreq_quick_get+0x10/0x30
[<ffffffff8103f12b>] show_cpuinfo+0x2ab/0x300
[<ffffffff81136292>] seq_read+0xf2/0x3f0
[<ffffffff8126c5d3>] ? __strncpy_from_user+0x33/0x60
[<ffffffff8116850d>] proc_reg_read+0x6d/0xa0
[<ffffffff81116e53>] vfs_read+0xc3/0x180
[<ffffffff81116f5c>] sys_read+0x4c/0x90
[<ffffffff81030dbb>] system_call_fastpath+0x16/0x1b
...
It's all cause by weird fail path handling in cpufreq_register_driver.
To fix that, shuffle the code to do proper handling with gotos.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Dave Jones <davej@redhat.com>
Add these new power trace events:
power:cpu_idle
power:cpu_frequency
power:machine_suspend
The old C-state/idle accounting events:
power:power_start
power:power_end
Have now a replacement (but we are still keeping the old
tracepoints for compatibility):
power:cpu_idle
and
power:power_frequency
is replaced with:
power:cpu_frequency
power:machine_suspend is newly introduced.
Jean Pihet has a patch integrated into the generic layer
(kernel/power/suspend.c) which will make use of it.
the type= field got removed from both, it was never
used and the type is differed by the event type itself.
perf timechart userspace tool gets adjusted in a separate patch.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: rjw@sisk.pl
LKML-Reference: <1294073445-14812-3-git-send-email-trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <1290072314-31155-2-git-send-email-trenn@suse.de>
Indent the body of for_each_cpu.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch fixes up a brace warning found by the checkpatch.pl tool
Signed-off-by: Neal Buckendahl <nealb001@tbcnet.com>
Signed-off-by: Dave Jones <davej@redhat.com>
and fix the broken case if a core's frequency depends on others.
trace_power_frequency was only implemented in a rather ungeneric way
in acpi-cpufreq driver's target() function only.
-> Move the call to trace_power_frequency to
cpufreq.c:cpufreq_notify_transition() where CPUFREQ_POSTCHANGE
notifier is triggered.
This will support power frequency tracing by all cpufreq drivers
trace_power_frequency did not trace frequency changes correctly when
the userspace governor was used or when CPU cores' frequency depend
on each other.
-> Moving this into the CPUFREQ_POSTCHANGE notifier and pass the cpu
which gets switched automatically fixes this.
Robert Schoene provided some important fixes on top of my initial
quick shot version which are integrated in this patch:
- Forgot some changes in power_end trace (TP_printk/variable names)
- Variable dummy in power_end must now be cpu_id
- Use static 64 bit variable instead of unsigned int for cpu_id
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: davej@redhat.com
CC: arjan@infradead.org
CC: linux-kernel@vger.kernel.org
CC: robert.schoene@tu-dresden.de
Tested-by: robert.schoene@tu-dresden.de
Signed-off-by: Dave Jones <davej@redhat.com>
lock_policy_rwsem_* and unlock_policy_rwsem_* functions are scheduled
to be unexported when 2.6.33. Now there are no other callers of them
out of cpufreq.c, unexport them and make them static.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
395913d0b1 ("[CPUFREQ] remove rwsem lock
from CPUFREQ_GOV_STOP call (second call site)") is not needed, because
there is no rwsem lock in cpufreq_ondemand and cpufreq_conservative
anymore. Lock should not be released until the work done.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=1594
Signed-off-by: Andrej Gelenberg <andrej.gelenberg@udo.edu>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Multiple modules used to define those which are with identical
functionality and were needlessly replicated among the different cpufreq
drivers. Push them into the header and remove duplication.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1270065406-1814-7-git-send-email-bp@amd64.org>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There is no need to do sysfs_remove_link() or kobject_put() etc.
when policy_rwsem_write is held, move them after releasing the lock.
This fixes the lockdep warning:
halt/4071 is trying to acquire lock:
(s_active){++++.+}, at: [<c0000000001ef868>] .sysfs_addrm_finish+0x58/0xc0
but task is already holding lock:
(&per_cpu(cpu_policy_rwsem, cpu)){+.+.+.}, at: [<c0000000004cd6ac>] .lock_policy_rwsem_write+0x84/0xf4
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Constify struct sysfs_ops.
This is part of the ops structure constification
effort started by Arjan van de Ven et al.
Benefits of this constification:
* prevents modification of data that is shared
(referenced) by many other structure instances
at runtime
* detects/prevents accidental (but not intentional)
modification attempts on archs that enforce
read-only kernel data at runtime
* potentially better optimized code as the compiler
can assume that the const data cannot be changed
* the compiler/linker move const data into .rodata
and therefore exclude them from false sharing
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
