* Get power table offset from the EEPROM instead of using
a hardcoded value of -5 if the EEPROM rev is >= 21.
* Add support in the 4k eeprom code for tx power offset
in case we have a 4k AR9280 implementation.
* Fix tx power accuracy at high powers.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has to be done if the EEPROM supports FCC Midband
capability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce PLL Settle time and eliminate redundant PLL calls. Also reduce
the LoadNF timeout from 10 msec to 250usec as the 10 msec timeout was
hit with AR9285 in some cases.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clearing a local variable is unnecessary.
Get rid of it.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Move 0xa274 and 0xa27c to the top of tx_gain table.
* Update initvals to fix random failure of noise floor calibration.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR5416 chipsets, clearing RTC_RESET_EN when setting
the chip to SLEEP mode results in high power consumption.
This patch fixes this issue by not clearing it for AR5416.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the current channel is between 2412 and 2472 MHz and if the channel is
changing to 2484 MHz, then the registers 0xa1f4, 0xa1f8 and 0xa1fc need to be
programmed to the "japan_2484" values. Conversely, if the current channel
is 2484 MHz and if the channel is changing to one between 2412 and 2472 MHz, then
the three registers need to be programmed to the "normal" values.
This is needed for compliance with Japanese regulatory requirements.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Prevent divide-by-zero errors in IQ Calibration.
* Do not run temperature compensation if initPDADC or currPDADC is zero.
* Also, introduce a separate function for handling OLC for AR9287.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ar9170_op_get_tsf: handle a carry from TSF_L into TSF_H
by reading TSF_H twice.
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add heavy clip handling for 2.4GHz only (similar to the vendor driver).
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes some coding style issues and moves MAX_RATE_POWER into hw.h
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module firmware information of 1000 series is missing from iwlagn.
Signed-off-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using powersave while idle saves a lot of power, but
we've had problems with this on some cards (5150 has
been reported to be problematic). However, on the new
6000 series we're seeing no problems, so for now let
that hardware benefit from idle mode, we can look at
the problems with other hardware one by one and then
enable those once we figure out the problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding support of Chain Noise Calibration for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When instructing the microcode to use just a single
chain when we have power saving enabled, we should
also tell the AP that we are doing SM powersave.
However, using a single chain doesn't actually have
any power saving advantage while idle -- measurements
show that the power consumption is no different when
using one vs. two or three chains.
Therefore, always instruct the microcode to use all
chains.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never have four chains, but let's fix the typo
while we noticed it. You count 0, 1, 2, 3, not
0, 1, 2, 4 :)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Today's implementation allow LED to blink based on the traffic
condition. We introduce an additional LED mode that reflects the RF
state.
The supported LED modes after this are:
IWL_LED_BLINK (current/default) - blink rate based on current Tx/Rx
traffic
IWL_LED_RF_STATE (new) -
LED OFF: No power/RF disabled, the LED is emitting no light
LED ON: Powered/RF enabled, the LED is emitting light
in a stable non-flashing state.
In order to provide the flexibility to support different LED
behavior per user/system preference we add "led_mode" iwlcore module
parameter.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update PCI Subsystem ID for 60x0 series based on HW SKU. Adding new SKU
for "ABG" and "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update PCI Subsystem ID for 1000 series based on HW SKU. Adding new SKU
for "BG" only devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for uCode to select the valid antennas for transmit, driver
need to configure the allowed tx antennas through host command.
The TX_ANT_CONFIGURATION_CMD should be used for 5000 series and up
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current rate scale algorithm fluctuates between different MIMO modes fairly
rapidly, causing widely varying performance. These fluctuations occur because in
the rate_scale tables for expected throughput the values are not very different
for different modes.
However, when aggregation is turned on and MAC overhead is reduced, the
expected throughput for different MIMO modes grows and different modes have
vastly different performance. Add expected throughput tables for this case.
We also need to keep track of aggregation status per-station, so we add the
"is_agg" field to struct lq_sta.
Also includes cleanup of comments and variable names in/around the affected
code.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OR-in AMPDU flags rather than assigning them. This lets the TX status for
aggregated packets be processed by rs_tx_status.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cut down on redundant code, reorganize structure, and add/improve comments.
Should contain no functional changes.
Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcode module parameter's permissions, use pre-defined.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update EEPROM version requirement for 1000 and 6000 series of NIC
for EEPROM version verification.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow user to change protection mechanism for HT between RTS/CTS and
CTS-to-self through sysfs:
Show current protection mechanism for HT
cat /sys/class/net/wlan0/device/rts_ht_protection
Change protection mechanism for HT (only allowed while not-associated)
CTS-to-self:
echo 0 > /sys/class/net/wlan0/device/rts_ht_protection
RTS/CTS:
echo 1 > /sys/class/net/wlan0/device/rts_ht_protection
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chain settings we currently use in iwlwifi are
rather confusing -- and we also go by the wrong
settings entirely under certain circumstances. To
clean it up, create a new variable in the current
HT config -- single_chain_sufficient -- that tells
us whether we need more than one chain. Calculate
that based on the AP and operating mode (no IBSS
HT implemented -- so no need for multiple chains,
for station mode we use the AP's capabilities).
Additionally, since APs always send disabled SM PS
mode, keeping track of their sm_ps mode isn't very
useful -- doubly not so for our _own_ RX config
since that should depend on our, not the AP's, SM
PS mode.
Finally, document that our configuration of the
number of RX chains used is currently wrong when
in powersave (by adding a comment).
All together this removes the two remaining items
in struct iwl_ht_config that were done wrong there.
For the future, the number of RX chains and some
SM PS handshaking needs to be added to mac80211,
which then needs to tell us, and the new variable
current_ht_config.single_chain_sufficient should
also be calculated by mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show version number along with dumping NVM data, the version information
being removed from sysfs, add it back to debugfs to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Halperin pointed out that the naming
here is rather inconsistent with at least 3
different names being used for one thing in
different contexts. Rename the struct to
iwl_ht_config (rather than iwl_ht_info) and
use ht_conf as a variable for it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel C Halperin <daniel.c.halperin@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust led blink rate to compensate on a MAC Clock difference on every
HW. Led blink rate analysis showed an average deviation of 0% on 3945,
5% on 4965 HW and 20% on 5000 series and up.
Need to compensate on the led on/off time per HW according to the
deviation to achieve the desired led frequency
The calculation is: (100-averageDeviation)/100 * blinkTime
For code efficiency the calculation will be:
compensation = (100 - averageDeviation) * 64 / 100
NewBlinkTime = (compensation * BlinkTime) / 64
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
is_ht can be bool instead of u8, and there's
no need to use IWL_CHANNEL_WIDTH_* constants
in supported_chan_width when that could just
be named is_40mhz instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Separate set_hw_params() function for 6000
series from 5000/1000 series because:
1) 6000 series use different set of sensitivity range table
2) 6000 series has different uCode image size
Also include the new sensitivity parameters needed by sensitivity
algorithm.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different NIC has different requirements for configuration. Currently all
5000 series hardware and later share the same configuration function even
though they do not need the same configurations. Fix this by separating the
needed configuration actions for each hardware model.
.5000 series: L1-ASPM H/W bug work-around
configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
work-around for NIC get stuck after early PCIe power off
.1000 series: write CSR_HW_IF_CONFIG_REG for uCode use
setting digital SVR for 1000 card to 1.32V
.6000 series: configure radio
write CSR_HW_IF_CONFIG_REG for uCode use
write CSR_GP_DRIVER_REG to indicate radio sku
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove few of the parameters not used and no longer valid in EEPROM.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify LED blink index table to include 1Mbps.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the last part to make ath9k hw code core driver agnostic.
I believe ath9k_htc can now use use the hw code unmodified.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac.c is now core driver independent.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
hw code will be shared between ath9k and ath9k_htc.
Just a few more files are left to clean up, mark them as well.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used just to determine how to program the MAC,
either for 20 MHz operation of 40 MHz so just use conf_is_ht40()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was for supporting 25 MHz spacing for HT40, this is not used
as we use 20 MHz spacing instead for HT40 as per 802.11n. The hardware
is capable of it though so we leave the phymode definition and EEPROM
parsing for it. If some experimenter wants to work on this stuff stuff
you can add an extension enabling bool on ath_common and perhaps some
debugfs knob to enable it. Keep in mind you'll also need to update the
phymode with the AR_PHY_FC_DYN2040_EXT_CH which has been left on the
driver.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k uses this for now, ath9k_htc is expected to re-use this
as well. We lave ath5k as is, but it certainly can also be
converted later.
The ath9k module parameter and debugfs entry is kept.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of it on hw code in ath9k to avoid
using the ath9k ath_softc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also make ath5k and ath9k use it, and share register definitions.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only common ath read/write ops go through the common ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can propagate better errors upon failed hw initialization,
and set up the ath_common structure for attach purposes. This
will become important once we start using the ath_common
for read/write ops.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In an effort to make hw code driver core agnostic read
and write operations are defined on the ath_common structure.
This patch adds that and makes ath9k use it. This allows
drivers like ath9k_htc to define its own read/write ops and
still rely on the same hw code. This also paves the way for
sharing code between ath9k/ath5k/ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We disable ASPM when enabling bluetooth coexistance. Disabling
ASPM is a bus specific operation. In the future other buses may
support bluetooth coexistance, an example is USB. To this end
move the current routine which disables ASPM into pci.c, and declare
it the PCI bt_coex_prep() helper. Additionally, since ASPM is
a PCI-Express primitive ensure we don't ever try to muck with ASPM
registers on non PCI-express devices.
This also cleans up hw.c to not include bus specific headers or
utilities.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Cc: Stephen Chen <stephen.chen@atheros.com>
Cc: Zhifeng Cai <zhifeng.cai@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ensures that we can access common on hw related code
independent of the driver core.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse warning:
CHECK drivers/net/wireless/ath/ath5k/attach.c
drivers/net/wireless/ath/ath5k/attach.c:288:42: warning: symbol 'ee' shadows an earlier one
drivers/net/wireless/ath/ath5k/attach.c:109:34: originally declared here
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ah_sta_id was really being used as the macaddr.
ath5k still does not use the association ID now passed
up by mac80211, that can be fixed later.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are common amongst ath9k and ath5k, so put them into the
common structure and make ath9k to use it. ar9170 can use macaddr,
and curbssid. We'll change ath5k and ar9170 separately.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the already provided helper instead of rewriting the code
required in place.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The same code was being implemented on reset for setting the bssidmask,
instead just use the already provided helper.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Historically some macro helpers have been users for this,
AR5K_LOW_ID() and AR5K_HIGH_ID(), use upstream unaligned
helpers instead. This applid to ath5k and ar9170. ath9k
already uses this.
Worth noting is ath5k uses an ah_sta_id but that is already
the MAC address combined with the associaiton ID, ah_sta_id
is really ETH_ALEN in size.
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Nick Kossifidis <mick@madwifi-project.org>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used by both ath5k and ath9k to set the first bssid mask.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_setpower_nolock --> ath9k_hw_setpower()
ath9k_hw_setpower() --> ath9k_setpower()
Also change the param for ath9k_setpower() to pass the ath_softc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_setpower() is a core driver helper with locking
protection. Locking protection should be left to the driver
core, not the hw code. Hardware code no longer contends for
locking when it needs to wake up the chip or put it to sleep.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the TSF is reset power save state is disabled and
then restored. The helpers to disable power save and restore
it use a lock provided by the driver core. Move the callers
of the helpers outside of the hw code.
We reset the TSF when mac80211 tells us and on the beacon.c
helper ath9k_hw_beaconinit() when it is made explicitly required.
Add a helper on beacon.c which will deal with ps awake/restore
if we need to reset the TSF upon ath9k_hw_beaconinit().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also just pass the ath_hw as the parameter.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are only used by btcoex.c on one routine, so stuff them
into that file.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After some necessary cleanups we now move ath9k_hw_btcoex_set_weight()
to where it belongs.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The second argument is always the hardware bt coex struct, so
remove it, and rename the function on the path with a ath9k_ prefix.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
btcoex_scheme is already part of a btcoex struct, its implied
this is btcoex related.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bt_stomp_type defines the bt coex weight, it has a one-to-one
mapping. In the future we may want to just use the weight directly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whether or not bluetooth coex has been enabled is a hardware
state and only the hardware helpers will be able to set this.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One for 2-wire and another for 3-wire.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Keep on btcoex.c only hardware access helpers, move the
driver core specific code to main.c. To accomplish
this we had to split ath_init_btcoex_info() into two parts,
the driver core part -- ath_init_btcoex_timer() and the hw
specific part -- ath9k_hw_init_btcoex_hw_info(). This
highlights how ath_gen_timer is part of the driver core, not
hw related, so stuff that into ath_btcoex struct.
The ath9k_hw_btcoex_init() code is now put inline on
ath_init_softc() through a switch to it easier to follow,
since we did that we can now call ath_tx_get_qnum() from
the main.c instead of btcoex.c
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a helper for 2-wire and another for 3-wire.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now access it via the ath_hw declare the ath_hw pointer
at the header of some routines and se it. ath9k.h no longer needs to
access btcoex.h and to adjust for this move ath_btcoex_set_weight()
into btcoex.h and instead give main.c a helper for setting initial
values upon drv_start()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is some bluetooth coexistance data which is driver
specific, stuff that into its own structure.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DPRINTF() is used in hw specific related code, as such
ensure we don't rely on the private driver core ath_softc
struct when calling it. Drivers can then implement their
own DPRINTF() as they see fit.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The DMA-API debugging facility complains about b43 mapping memory from
stack for SDIO-based cards.
Indeed, b43 currently allocates the PIO RX/TX header and tail buffers
from stack. The solution here is to use heap-allocated buffers instead.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In Bugzilla No. 14181, a PowerMac G4 crashes on ifdown or
module unload because the rfkill polling has not been stopped.
For the x86 architectures, the attempt to reach a now unmapped
register is not fatal as it is on PPC.
(Includes "b43: Fix locking problem when stopping rfkill polling". -- JWL)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A logical of shifts to the left doesn't make sense.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
User-visible messages should use formatted MAC addresses ("00:01:...")
rather than raw ("0001...") so they match other parts of the system.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: ilw@linux.intel.com
CC: linux-wireless@vger.kernel.org
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix IRQ mask sanity check for physically pulled device.
Tested-by: Andrew Price <andy@andrewprice.me.uk>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return type of abs() was recently changed from int to long. With
min()'s type checking we thus need to make sure that values of the same
type are compared.
This fixes:
CC [M] drivers/net/wireless/iwlwifi/iwl-5000.o
drivers/net/wireless/iwlwifi/iwl-5000.c: In function ‘iwl5000_gain_computation’:
drivers/net/wireless/iwlwifi/iwl-5000.c:320: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes following on big endian systems:
CC [M] drivers/net/wireless/iwlwifi/iwl-rx.o
drivers/net/wireless/iwlwifi/iwl-rx.c: In function ‘iwl_rx_reply_rx’:
drivers/net/wireless/iwlwifi/iwl-rx.c:1029: warning: integer overflow in
expression
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the correct EEPROM offset for enhance tx power for 6000 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The address stored in the next link address is a word address but when
reading the OTP blocks, a byte address is used. Also if the blocks are
full and the last link pointer is not zero, then none of the blocks are
valid so return an error.
The algorithm is simply valid blocks have a next address and that
address's contents is zero.
Using the wrong address for the next link address gets arbitrary data,
obviously. In cases seen, the first block is considered valid when it is not.
If the block has in fact been invalidated there may be old data or
there may be no data, bad data, or partial data, there is no way of
telling. Without this patch it is possible that a device with valid OTP data
is unable to work.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't use struct wldev after detach. This fixes an oops on access.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only 128 buffer descriptors are supported in the core. Limit the
number in case we have more memory.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enabled the ethoc to allocate system memory as buffer
when there is no dedicated buffer memory.
Some hardware designs may not have dedicated buffer memory such as
on chip or off chip SRAM. In this case, only one memory resource is
supplied in the platform data instead of two. Then a DMA buffer can
be allocated from system memory and used for the transfer.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet buffer is allocated at 4 bytes boundary, but the IP header
length and version bits is located at byte 14. These bit fields access
as 32 bits word and caused exception on processors that do not support
unaligned access.
The patch adds 2 bytes offset to make the bit fields word aligned.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer address in buffer descriptors is physical address. The
pointer that processor used to access packet is virtual address.
Though the higher bits of pointer address used by the MAC may be
truncated to zero in special case, it is not always true in larger
designs.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should be max() instead of min(). Use 1/4 of available
descriptors for tx, and there should be at least 2 tx
descriptors.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
in update_rx_stats() the RX_OVERLEN bit is set twice, replace it by RX_RUNT.
in au1000_rx() the RX_MISSED_FRAME bit was tested a few lines earlier already
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The closing parenthesis was not on the right location.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all pasemi mac interfaces can have a phy attached.
For example, XAUI has no phy and phydev is NULL for it.
In this case ethtool get settings causes kernel crash.
Fix it by returning -EOPNOTSUPP if there's no PHY attached.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Radensky noted that chip resets were generating stack trace dumps.
This is because the driver is attempting to acquire the mdio bus mutex
while holding the tp->lock spinlock. The fix is to change the code such
that every phy access takes the tp->lock spinlock instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter doesnot need to maintain a copy of net_device_stats.
Use the one already available in net_device. This patch takes care of the same.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data center bridging ops structure can be const
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All usages of structure net_proto_ops should be declared const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive_buf methods of the N_PPP and N_SYNC_PPP line disciplines,
ppp_asynctty_receive() and ppp_sync_receive(), call tty_unthrottle()
which may sleep. Fix the comments claiming otherwise.
Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases there is not desirable to switch back to primary interface when
it's link recovers and rather stay with currently active one. We need to avoid
packetloss as much as we can in some cases. This is solved by introducing
primary_reselect option. Note that enslaved primary slave is set as current
active no matter what.
Patch modified by Jay Vosburgh as follows: fixed bug in action
after change of option setting via sysfs, revised the documentation
update, and bumped the bonding version number.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a Kernel CAPI interface to the Gigaset driver.
Impact: optional new functionality
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dummy LL interface to the Gigaset driver so that it can be
built and, in a limited way, used without the ISDN4Linux subsystem.
Impact: new configuration alternative
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorganize the code of the Gigaset driver, moving all isdn4linux
dependencies to the source file i4l.c so that it can be replaced
by a file capi.c interfacing to Kernel CAPI instead.
Impact: refactoring, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add kerneldoc comments to some functions in the Gigaset driver.
Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump payload data consistently only when DEBUG_STREAM_DUMP debug bit
is set.
Impact: debugging aid
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Gigaset base stops responding, try resetting the USB
connection to recover.
Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear out pending command that got rejected with 'ERROR' response.
This fixes the bug where unloading the driver module would hang
with the message: "gigaset: not searching scheduled commands: busy"
after a device communication error.
Impact: error handling bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mention in the driver load announcement whether the driver was built
with debugging messages enabled, to facilitate support.
Impact: informational message
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't drop the remainder of an URB if an isochronous frame has an error.
Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code of the Gigaset driver assumes that sk_buff-s coming
from the ISDN4Linux subsystem are always linear. Explicitly
calling skb_linearize() is cheap if they are, but much more
robust in case they ever aren't.
Impact: robustness improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signal D channel disconnect in a few cases where it was missed,
including when an incoming call is disconnected before it was
accepted.
Impact: error handling improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Being able to change the debugmode module parameter of capidrv on the
fly is quite useful for debugging and doesn't do any harm.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several places, capidrv sends a CAPI message to the ISDN
device and then updates its internal state accordingly.
If the response message from the device arrives before the
state is updated, it may be rejected or processed incorrectly.
Avoid these races by updating the state before emitting the
message.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Info values in the 0x00xx range are defined in the CAPI standard
as "Informational, message processed successfully". Therefore a
CONNECT_B3_CONF message with an Info value in that range should
open an NCCI just as with Info==0.
Impact: minor bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for a bug which was a result of wrong use of checksum offload flag.
The status of tx-checksumming was not changed from on to off
after a 'ethtool -K <ifname> tx off' operation.
Use the proper checksum offload flag NETIF_F_HW_CSUM instead of
NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM.
Patch is against net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCC_STATUS_NOT_SUPPORTED should be decimal 66 not hex 66.
This patch fixes this typo. Patch against net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While updating the statistics to be passed via the get_stats,
tx multicast frames were being accounted instead of rx multicast frames.
This patch fixes the bug. This patch is against the net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of spinlock and private mutex usage for exclusive access to the
HW semaphore register. rtnl_lock already creates exclusive access to
this register in all driver API.
Add rtnl to firmware worker threads that also use the HW semaphore register.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that we are not already polling firmware events before we queue the
firmware event worker, then disable firmware interrupts.
Otherwise we can queue the same event multiple times.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Allow multiple functions with INTA.
- Removed the condition to allow only one vpath with INTA
- Ensure that the alarm bit in titan_mask_all_int register is cleared when
driver exits.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added a function to check if FCS stripping is disabled by the firmware, if
it is not disabled fail driver load.
- By default FCS stripping is disabled by the firmware. With this assumption
driver decrements the indicated packet length by 4 bytes(FCS length).
- This patch ensures that FCS stripping is disabled during driver load time.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Removed the wrr_rebalance function
- This feature is not supported by the ASIC, hence removing the related code.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix a crash in PAE system due to wrong typecasting.
- On PAE system size_t is unsigned int which is 32bit. Avoid casting
64 bit address to 32 bit
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Removed accessing GENDMA_INT register
- This allowed the firmware to perform a generic DMA write to host memory.
This feature is not supported by the ASIC, this patch removes access to
GENDMA_INT register.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update driver_config->vpath_per_dev for each function in probe.
- vpath_per_device specifies number of vpaths supported for each function/device. The
current code was updating vpath_per_device only for physical device, however this has
to be updated for each function also in case of a MF(Multi function) device.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- vxge driver was assuming function-0 is always the privilaged function. Now that
restriction has been removed any function can act as a privilaged function.
- This patch modifies the __vxge_hw_device_is_privilaged routine to not assume
function-0 as the privileged function.
- Recreated the patch by incorporating review comments from Dave Miller to
remove double slash in path names.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some switches that will do write combining when they see two
sequential regions written. In order to avoid any possible write combining
issues it is necessary to add a flush after writing each piece of a rar
register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This update adds additional exception handling to the phy code to handle
situations where it may be called incorrectly. In addition it adds some
bounds checking to the cable length checks to prevent an array overrun in
the event that the hardware returned a different value than expected.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a retry to phy reads in the event of failure. The original
code broke out of the loop on failure and this is a mistake as we should be
trying to do the read twice.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the generic portion of the copper link setup into a
seperate function in e1000_phy.c. This helps to reduce the size of
copper_link_setup_82575 and make it a bit more readable.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb doesn't have any devices that use a microwire interface for NVM. As
such the code related to this can be removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows us to treat the alternate mac address as though it is the
physical address on the adapter. This is accomplished by letting the
alt_mac_address function to only fail on an NVM error. If no errors occur
and the alternate mac address is not present then RAR0 is read as the
default mac address.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mailbox timeout routines need to be updated as they were not correctly
handling the case of a mailbox timeout and could cause issues with long
delays when used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the read and write mailbox functions need to acquire the mailbox lock.
Since that is the case we might as well combine both of the procedures into
one function so it is easier to maintain.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the device ID necessary to support the 82576NS SerDes
adapter.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support functions such as vlan tag stripping when SR-IOV is
enabled any given packet must match at least one filter. However in the
case of promiscous mode being enabled on the PF the traffic routed to it
may not match any filters and is just sent to the PF by default. In order
to make certain that this traffic is processed we can set all bits in the
UTA registers to create a pseudo promiscous mode filter that accepts all
packets.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds igb_rar_qsel which sets the mac address and pool bits for a
given mac address in the receive address register table.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of sgmii support isn't correctly locking the
interfaces for reads/writes. This change pulls the read/write
functionality out of 82575.c and moves it to phy.c. In addition it
replaces the implementation in 82575.c with one that uses locking around
the relocated i2c interface calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current approach is just using a ?: type mechanism to set the phy
locking bit. This if fine for now but limits us to only 2. Switch to a
nested if statement for future compatiblity with more than 2 phys.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This update corrects the driver so that it handles duplex for serdes links
correctly instead of just forcing full duplex always.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a temp variable in the stats clearing path that isn't needed since
the results from the stats read can be immediately discared. Since it
isn't needed we might as well just drop it from the function call.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7069331 (connector: Provide the sender's credentials to the
callback, 2009-10-02) changed callbacks to take two arguments but missed
this one.
drivers/connector/cn_proc.c: In function ‘cn_proc_init’:
drivers/connector/cn_proc.c:263: warning: passing argument 3 of
‘cn_add_callback’ from incompatible pointer type
Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug that got introduced in commit 76998bc7.
During preparation of mcc wrb, req was being wrongly overwritten
and the flash operation was failing.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For usbnet devices with FLAG_WLAN and FLAG_WWAN set the proper device
type so that uevent contains the correct value. This then allows an easy
identification of the actual underlying technology of the Ethernet device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for usbnet based devices like CDC-Ether to indicate that they
are actually mobile broadband devices. In that case use wwan%d as default
interface name.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs,serial_cs:
add cis of National Semicondoctor's lan&modem mulitifunction pcmcia card,
NE2K, tamarack ethernet card,
and some serial card(COMpad2, COMpad4).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BIT for macro definitions wherever possible, remove
unused and redundant macros.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These string query operations were supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert the remaining
implementations.
Also remove calls to these operations to initialise drvinfo->n_stats.
The ethtool core code already does that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This string query operation was supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert tehuti's
implementation.
Also remove the dummy self-test name which was not used since tehuti
does not advertise any self-tests.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This string query operation was supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert qeth's
implementation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There appears to have been a mixup in the max supported jumbo frame size
between 82574 and 82583 which ended up disabling jumbo frames on the 82574
as a result. This patch swaps the two so that this issue is resolved.
This patch fixes http://bugzilla.kernel.org/show_bug.cgi?id=14261
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds device support for the 82599 based X520 10GbE
Dual Port KX4 Mezzanine card.
Signed-off-by: Don Skidmore<donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will add support for the 82599 Dual port Backplane
device (0x10f8). This device has the ability to link in serial (KR) and
parallel (KX4/KX) modes, depending on what the switch capabilities are in
the blade chassis.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'acpi-pad' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
acpi_pad: build only on X86
ACPI: create Processor Aggregator Device driver
Fixup trivial conflicts in MAINTAINERS file.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: EC: Don't parse DSDT for EC early init on Compal
ACPI: EC: Rewrite DMI checks
ACPI: dock: fix "sibiling" typo
ACPI: kill overly verbose "throttling states" log messages
ACPI: Fix bound checks for copy_from_user in the acpi /proc code
ACPI: fix bus scanning memory leaks
ACPI: EC: Restart command even if no interrupts from EC
sony-laptop: Don't unregister the SPIC driver if it wasn't registered
sony-laptop: remove _INI call at init time
sony-laptop: SPIC unset IRQF_SHARED, set IRQF_DISABLED
sony-laptop: remove device_ctrl and the SPIC mini drivers
If i2c device probing fails, then there is no driver to dereference
after calling i2c_new_device(). Stop assuming that probing will always
succeed, to avoid NULL pointer dereferences. We have an easier access
to the driver anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Tim Shepard <shep@alum.mit.edu>
Cc: Colin Leroy <colin@colino.net>
When an ACPI resource conflict is detected, error messages are already
printed by ACPI. There's no point in causing the driver core to print
more error messages, so return one of the error codes for which no
message is printed.
This fixes bug #14293:
http://bugzilla.kernel.org/show_bug.cgi?id=14293
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which
implement device detection. The ab3100 driver doesn't, so there is no
point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
The I2C_CLIENT_INSMOD macro is only useful for i2c drivers which
implement device detection. The tsl2561 driver doesn't, so there
is no point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
The I2C_CLIENT_INSMOD_1 macro is only useful for i2c drivers which
implement device detection. The leds-pca9532 driver doesn't, so there
is no point in calling it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Riku Voipio <riku.voipio@iki.fi>
There is no point in implementing a detect callback for the LTC4215
and LTC4245, as these devices can't be detected. It was there solely
to handle "force" module parameters to instantiate devices, but now
we have a better sysfs interface that can do the same.
So we can get rid of the ugly module parameters and the detect
callbacks. This shrinks the binary module sizes by 36% and 46%,
respectively.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
There is no point in implementing a detect callback for the DS2482, as
this device can't be detected. It was there solely to handle "force"
module parameters to instantiate devices, but now we have a better sysfs
interface that can do the same.
So we can get rid of the ugly module parameters and the detect callback.
This shrinks the binary module size by 21%.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
There is no point in implementing a detect callback for the MAX6875, as
this device can't be detected. It was there solely to handle "force"
module parameters to instantiate devices, but now we have a better sysfs
interface that can do the same.
So we can get rid of the ugly module parameters and the detect callback.
This basically divides the binary module size by 2.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (41 commits)
Revert "Seperate read and write statistics of in_flight requests"
cfq-iosched: don't delay async queue if it hasn't dispatched at all
block: Topology ioctls
cfq-iosched: use assigned slice sync value, not default
cfq-iosched: rename 'desktop' sysfs entry to 'low_latency'
cfq-iosched: implement slower async initiate and queue ramp up
cfq-iosched: delay async IO dispatch, if sync IO was just done
cfq-iosched: add a knob for desktop interactiveness
Add a tracepoint for block request remapping
block: allow large discard requests
block: use normal I/O path for discard requests
swapfile: avoid NULL pointer dereference in swapon when s_bdev is NULL
fs/bio.c: move EXPORT* macros to line after function
Add missing blk_trace_remove_sysfs to be in pair with blk_trace_init_sysfs
cciss: fix build when !PROC_FS
block: Do not clamp max_hw_sectors for stacking devices
block: Set max_sectors correctly for stacking devices
cciss: cciss_host_attr_groups should be const
cciss: Dynamically allocate the drive_info_struct for each logical drive.
cciss: Add usage_count attribute to each logical drive in /sys
...
A couple of people have hit the WARN_ON() in drivers/char/tty_io.c,
tty_open() that is unhappy about seeing the tty line discipline go away
during the tty hangup. See for example
http://bugzilla.kernel.org/show_bug.cgi?id=14255
and the reason is that we do the tty_ldisc_halt() outside the
ldisc_mutex in order to be able to flush the scheduled work without a
deadlock with vhangup_work.
However, it turns out that we can solve this particular case by
- using "cancel_delayed_work_sync()" in tty_ldisc_halt(), which waits
for just the particular work, rather than synchronizing with any
random outstanding pending work.
This won't deadlock, since the buf.work we synchronize with doesn't
care about the ldisc_mutex, it just flushes the tty ldisc buffers.
- realize that for this particular case, we don't need to wait for any
hangup work, because we are inside the hangup codepaths ourselves.
so as a result we can just drop the flush_scheduled_work() entirely, and
then move the tty_ldisc_halt() call to inside the mutex. That way we
never expose the partially torn down ldisc state to tty_open(), and hold
the ldisc_mutex over the whole sequence.
Reported-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Heinz Diehl <htd@fancy-poultry.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Compal DSDT breaks if scanned early, while we need early scan
for almost all ASUS machines. Safest workaround seems to be to
continue do an early scan for all machines, but this Compal model.
http://bugzilla.kernel.org/show_bug.cgi?id=14086
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Use dmi_check_system() for DMI matching.
Don't use string "Notebook" for matching MSI hardware.
http://bugzilla.kernel.org/show_bug.cgi?id=14081
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
sfi_verify_table() is called at runtime, and thus cannot be __init
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Crossword clues as haikus:
Snakes from the same brood
fighting Jackson on a plane?
sibilant siblings
I guess Will Shortz's job is still secure.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
I was recently lucky enough to get a 64-CPU system. The processors
actually have T-states, so my kernel log ends up with 64 lines like:
ACPI: Processor [CPU0] (supports xx throttling states)
This is pretty useless clutter because
- this info is already available after boot from
/proc/acpi/processor/CPUnn/throttling
- there's also an ACPI_DEBUG_PRINT() in processor_throttling.c that
gives the same info on boot for anyone who *really* cares.
So just delete the code that prints the throttling states in
processor_core.c.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The function sfi_map_memory/sfi_unmap_memory uses
early_ioremap/early_iounmap respectively, which refers to a __init
function. And function sfi_check_table also refers to a __init function
sfi_verify_table. Since the references are valid, so use __ref to get rid
of the warnings.
We were warned by the following warnings:
LD vmlinux.o
MODPOST vmlinux.o
WARNING: vmlinux.o(.text+0xb6ba3a): Section mismatch in reference from
the function sfi_map_memory() to the function
.init.text:early_ioremap()
The function sfi_map_memory() references
the function __init early_ioremap().
This is often because sfi_map_memory lacks a __init
annotation or the annotation of early_ioremap is wrong.
WARNING: vmlinux.o(.text+0xb6bab6): Section mismatch in reference from
the function sfi_unmap_memory() to the function
.init.text:early_iounmap()
The function sfi_unmap_memory() references
the function __init early_iounmap().
This is often because sfi_unmap_memory lacks a __init
annotation or the annotation of early_iounmap is wrong.
WARNING: vmlinux.o(.text+0xb6be30): Section mismatch in reference from
the function sfi_check_table() to the function
.init.text:sfi_verify_table()
The function sfi_check_table() references
the function __init sfi_verify_table().
This is often because sfi_check_table lacks a __init
annotation or the annotation of sfi_verify_table is wrong.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI /proc write() code takes an unsigned length argument like any write()
function, but then assigned it to a *signed* integer called "len".
Only after this is a sanity check for len done to make it not larger than 4.
Due to the type change a len < 0 is in principle also possible; this patch
adds a check for this.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (46 commits)
cnic: Fix NETDEV_UP event processing.
uvesafb/connector: Disallow unpliviged users to send netlink packets
pohmelfs/connector: Disallow unpliviged users to configure pohmelfs
dst/connector: Disallow unpliviged users to configure dst
dm/connector: Only process connector packages from privileged processes
connector: Removed the destruct_data callback since it is always kfree_skb()
connector/dm: Fixed a compilation warning
connector: Provide the sender's credentials to the callback
connector: Keep the skb in cn_callback_data
e1000e/igb/ixgbe: Don't report an error if devices don't support AER
net: Fix wrong sizeof
net: splice() from tcp to pipe should take into account O_NONBLOCK
net: Use sk_mark for routing lookup in more places
sky2: irqname based on pci address
skge: use unique IRQ name
IPv4 TCP fails to send window scale option when window scale is zero
net/ipv4/tcp.c: fix min() type mismatch warning
Kconfig: STRIP: Remove stale bits of STRIP help text
NET: mkiss: Fix typo
tg3: Remove prev_vlan_tag from struct tx_ring_info
...
This fixes the problem of not handling the NETDEV_UP event properly
during hot-plug or modprobe of bnx2 after cnic. The handling was
skipped by mistakenly using "else if" to check for the event.
Also update version to 2.0.1.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only error returned by pci_{en,dis}able_pcie_error_reporting() is
-EIO which simply means that Advanced Error Reporting is not supported.
There is no need to report that, so remove the error check from e1000e,
igb and ixgbe.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Which is why I have always preferred sizeof(struct foo) over
sizeof(var).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free an acpi_get_object_info() buffer when we're finished. Skip the
acpi_get_name() altogether -- it was only used for a printk that was
really just for debug anyway.
http://bugzilla.kernel.org/show_bug.cgi?id=14271
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reported-and-tested-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
EC may forget a command without sending any "reset" interrupt,
thus we need to lessen the requirement for transaction restart.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=14247
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
spi_imx_chipselect() made things that should be (and mostly are) done by
spi_imx_setupxfer. Only setting the tx and rx functions was missing.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise the config function uses random data from the stack. This
didn't stick out because config is called once more in the chipselect
function with correct parameters.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spi_imx_setup() is only called by spi_setup(). The latter does the
initialization already.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can only setup the gpio pins in spi_setup time when we know the
SPI_CS_HIGH setting.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the filename match the Kconfig symbol and the driver name.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow users to force skipping the TXEN test at init time. Applies
to all serial ports. Intended for debugging only.
There is a blacklist for devices where we need to skip the test but the
list is not complete. This lets users force skipping the test so we can
determine if they need to be added to the list.
Some HP machines with weird serial consoles have this problem and there
may be more.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check whether index is within bounds before grabbing the element.
Also, since NR_PORTS is defined ARRAY_SIZE(cy_port), cy_port[NR_PORTS] is
out of bounds as well.
[akpm@linux-foundation.org: cleanup, remove (long) casts]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
irq is declared with size NR_CARDS (4), but the loop containing this
segment runs up until NR_ISA_ADDRS (16), possibly reading from irq[i] (and
trying to use the result)
Identified by the Parfait static scanner.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add better support for omitting either the card detect or the write
protect GPIOs if the board does not support it. Add the fields
no_wprotect and no_detect to the platform data which when set indicate the
absence of the respective GPIOs.
Note, this also fixes a minor bug where it tries to free IRQ0 if there is
no detect gpio available.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have found a couple of boards where the SDIO IRQ hardware support has
failed to work properly, and thus we should make it configurable whether
or not to be included in the driver.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes for the DMA transfer mode of the driver to try and improve the state
of the code:
- Ensure that dma_complete is set during the end of the command phase
so that transfers do not stall awaiting the completion
- Update the DMA debugging to provide a bit more useful information
such as how many DMA descriptors where not processed and print the
DMA addresses in hexadecimal.
- Fix the DMA channel request code to actually request DMA for the
S3CMCI block instead of whatever '0' signified.
- Add fallback to PIO if we cannot get the DMA channel, as many of the
devices with this block only have a limited number of DMA channels.
- Only try and claim and free the DMA channel if we are trying to use it.
This improves the driver DMA code to the point where it can now identify a
card and read the partition table. However the DMA can still stall when
trying to move data between the host and memory.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a selection for the data transfer mode of the s3cmci driver, allowing
for either a configuration or rumtime selection of the use of the DMA or
PIO transfer code.
The PIO only mode is 476 bytes smaller than the driver with both methods
compiled in.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The controller supports SDIO IRQ detection so add support for hardware
assisted SDIO interrupt detection for the SDIO core. This improves the
response time for SDIO interrupts and thus the transfer rate from devices
such as the Marvel 8686.
As a note, it does seem that the controller will miss an IRQ than is held
asserted, so there are some manual checks to see if the SDIO interrupt is
active after a transfer.
Major testing on the S3C2440.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export driver state and hardware register state via debugfs entries
created under a directory formed from dev_name() on the probed device when
CONFIG_DEBUG_FS is set.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clear_imask() call should be used to clear the interrupt mask
register, as it may end up clearing the SDIO interrupt bit if this is
enabled.
Change all writes of zero to SDIIMSK register to use clear_imask() ready
for the SDIO updates.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move to using dev_pm_ops for suspend and resume.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move to using gpiolib to access the card detect and write protect GPIO
lines instead of using the platform speicifc s3c2410_gpio calls.
Also ensure that the card lines are claimed the same way to avoid overlap
with any other drivers.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the platform id list to match the three different versions of the
hardware block that this driver supports.
This will change the prefix of the console messages produced by this
driver to be prefixed by s3c-mci instead of the hardware block name, such
as s3c2440-mci.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the local definition RESSIZE() with the standard resource_size()
call for getting the size of a struct resource.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some configurations of the Timberdale FPGA has the uartlite
included.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some manufacturers provide vendor information in non-vendor specific CIS
tuples. For example, Broadcom uses an Extended Function tuple to provide
the MAC address on some of their network cards, as in the case of the
Nintendo Wii WLAN daughter card.
This patch allows passing whitelisted FUNCE tuples unknown to the SDIO
core to a matching SDIO driver instead of rejecting them and failing.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/input/input.c:1277: warning: 'input_dev_reset' defined but not used
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is based on Michal Schmidt fix for skge.
Most network drivers request their IRQ when the interface is activated.
sky2 does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:
1. modprobe sky2
The card is detected as eth0 and requests IRQ 17. Directory
/proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
Now 8139too requests IRQ 17.
The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered
The fix is for sky2 to name the irq based on the pci device, as is done
by some other devices DRM, infiniband, ... ie. sky2@pci:0000:00:00
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most network drivers request their IRQ when the interface is activated.
skge does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:
1. modprobe skge
The card is detected as eth0 and requests IRQ 17. Directory
/proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
Now 8139too requests IRQ 17.
The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered
...
And "ls /proc/irq/17" shows two subdirectories, both called eth0.
Fix it by using a unique name for skge's IRQ, based on the PCI address.
The naming from the example then looks like this:
$ grep skge /proc/interrupts
17: 169 IO-APIC-fasteoi skge@pci:0000:00:0a.0, eth0
irqbalance daemon will have to be taught to recognize "skge@" as an
Ethernet interrupt. This will be a one-liner addition in classify.c. I
will send a patch to irqbalance if this change is accepted.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove references to dead web site mosquitonet.Stanford.EDU.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This typo was introduced by 5793f4be23 on
October 14, 2005 ...
Reported-by: Matti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
prev_vlan_tag field is not used.
Patch saves 512*8 bytes per tx queue ring on 64bit arches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Matthew Carlson <mcarlson@broadcom.com>
The function virtnet_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alex Williamson <alex.williamson@hp.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sgiseeq_remove is defined using __exit, so don't use
__devexit_p but __exit_p to wrap it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Wang Chen <wangchen@cn.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The function meth_remove is defined using __exit, so don't use __devexit_p
but __exit_p to wrap it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Primary module parameter passed to bonding is pernament. That means if you
release the primary slave and enslave it again, it becomes the primary slave
again. But if you set primary slave via sysfs, the primary slave is only set
once and it's not remembered in bond->params structure. Therefore the setting is
lost after releasing the primary slave. This simple one-liner fixes this.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prepare_discard_fn() was being called in a place where memory allocation
was effectively impossible. This makes it inappropriate for all but
the most trivial translations of Linux's DISCARD operation to the block
command set. Additionally adding a payload there makes the ownership
of the bio backing unclear as it's now allocated by the device driver
and not the submitter as usual.
It is replaced with QUEUE_FLAG_DISCARD which is used to indicate whether
the queue supports discard operations or not. blkdev_issue_discard now
allocates a one-page, sector-length payload which is the right thing
for the common ATA and SCSI implementations.
The mtd implementation of prepare_discard_fn() is replaced with simply
checking for the request being a discard.
Largely based on a previous patch from Matthew Wilcox <matthew@wil.cx>
which did the prepare_discard_fn but not the different payload allocation
yet.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix these build errors when CONFIG_PROC_FS is not set:
drivers/block/cciss.c: In function 'cciss_show_raid_level':
drivers/block/cciss.c:623: error: 'RAID_UNKNOWN' undeclared (first use in this function)
drivers/block/cciss.c:626: error: 'raid_label' undeclared (first use in this function)
drivers/block/cciss.c: In function 'cciss_geometry_inquiry':
drivers/block/cciss.c:2696: error: 'RAID_UNKNOWN' undeclared (first use in this function)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cciss: Dynamically allocate the drive_info_struct for each logical drive.
This reduces the size of the per-hba ctlr_info structure from 106936
bytes to 8132 bytes. That's on 32-bit systems. On 64-bit systems, the
improvement is even bigger. Without this, the ctlr_info struct is so big
that the driver won't even load on a 64 bit system if CISS_MAX_LUN was
at it's current setting of 1024 logical drives.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add usage_count attribute to each logical drive at
/sys/devices/<dev>/ccissX/cXdY/usage_count for controller X,
logical drive Y. The usage count is the number of times
the device has currently been opened.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
