Banks shouldn't be defined in DT if number of resources
per bank is not variable. We actually know that this SoC
has three banks so take that into account in order to don't
overspecify the device tree. Device tree will only have one
node making it simple. Update device tree, binding doc and
code accordly.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This currently fixes the remaining dtb warnings:
Node /pcie@1e140000/pcie0 has a reg or ranges property, but no unit name
Node /pcie@1e140000/pcie1 has a reg or ranges property, but no unit name
Node /pcie@1e140000/pcie2 has a reg or ranges property, but no unit name
Node /pcie@1e140000/pcie0 node name is not "pci" or "pcie"
Node /pcie@1e140000/pcie0 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie0 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie1 node name is not "pci" or "pcie"
Node /pcie@1e140000/pcie1 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie1 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie2 node name is not "pci" or "pcie"
Node /pcie@1e140000/pcie2 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie2 missing bus-range for PCI bridge
Warning (unit_address_format): Failed prerequisite 'pci_bridge'
Warning (pci_device_reg): Failed prerequisite 'pci_bridge'
Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge'
device_type was removed since according to documentation, it's deprecated
for pci(e) devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MT7621 documentation says that the sys clock - also known
as OCP clock for the Open Core Protocol - can be configured to
1/3 or 1/4 of the CPU clock.
Testing on my hardware, using the fact that the SPI clock is
based on the OCP clock and measuring transfer rates, shows
a clock of a little over 200MHz with a CPU clock of 900MHz.
So assume 1/4 is the default.
Also, the nor-flash in the gbpc1 is documented as accepting 50MHz
for request requests, and higher for other requests. So set
maximum to 50MHz.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most gpio chips have two cells for interrupts and this should be also.
Set this property in the device tree accordly fixing this up. In order
to make this working properly the xlate function for the irq_domain must
be updated to use the 'irq_domain_xlate_twocell' one in the driver.
One more minimal change is needed two refer gpio's interrupt-parent from
other nodes which is to add new 'gpio' label in the device tree.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to let other devices reference the GPIO interrupts
if necessary properties 'interrupt-controller' and
'#interrupt-cells' becomes necessary. Add both of them to
complete gpio device tree node.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO controller of mt7621 can receive interrupts on any
of the GPIOs, either edge or level. It then interrupts the CPU using
GIC INT12. Update device tree accordly.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gpio driver for mt7621 is using 'mtk' as binding but in the kernel
is already defined one for this maker which is 'mediatek'. Update
device tree to use the correct one.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the Interrupts for the PCI adapters are listed in
devicetree we shouldn't need to have them explicit in the code.
The simplest way to do this is to use of_irq_parse_and_map_pci()
and specify an interrupt-map which identifies the different
PCI hosts by bus/slot numbers.
This has the advantage that the hwirq number are mapped to virq
numbers for us, so the ugly hack can go.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace spaces with tabs in indentation.
Issue found with checkpatch.
Signed-off-by: Nishka Dasgupta <nishka.dasgupta_ug18@ashoka.edu.in>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device tree source for mt7621 and gnubee1 to
make testing easier.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
