This changes the writeX family of functions to have a sync instruction
before the MMIO store rather than after, because the generally expected
behaviour is that the device receiving the MMIO store can be guaranteed
to see the effects of any preceding writes to normal memory.
To preserve ordering between writeX and readX, and to preserve ordering
between preceding stores and the readX, the readX family of functions
have had an sync added before the load.
Although writeX followed by spin_unlock is not officially guaranteed
to keep the writeX inside the spin-locked region unless an mmiowb()
is used, there are currently drivers that depend on the previous
behaviour on powerpc, which was that the mmiowb wasn't actually required.
Therefore we have a per-cpu flag that is set by writeX, cleared by
__raw_spin_lock and mmiowb, and tested by __raw_spin_unlock. If it is
set, __raw_spin_unlock does a sync and clears it.
This changes both 32-bit and 64-bit readX/writeX. 32-bit already has a
sync in __raw_spin_unlock (since lwsync doesn't exist on 32-bit), and thus
doesn't need the per-cpu flag.
Tested on G5 (PPC970) and POWER5.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Call chip->eoi(irq) to clear any pending interrupt in case of kdump
shutdown sequence. chip->end(irq) does not serve this purpose.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix return value from memcpy
[POWERPC] iseries: Define insw et al. so libata/ide will compile
[POWERPC] Fix irq enable/disable in smp_generic_take_timebase
[POWERPC] Fix problem with time not advancing on 32-bit platforms
[POWERPC] Restore copyright notice in arch/powerpc/kernel/fpu.S
[POWERPC] Fix up ibm_architecture_vec definition
[POWERPC] Make OF irq map code detect more error cases
[POWERPC] Support for "weird" MPICs and fixup mpc7448_hpc2
[POWERPC] Fix MPIC sense codes in documentation
[POWERPC] Fix performance regression in IRQ radix tree locking
[POWERPC] Add mpc7448hpc2 device tree source file
[POWERPC] Add MPC8349E MDS device tree source file to arch/powerpc/boot/dts
[POWERPC] modify mpc83xx platforms to use new IRQ layer
[POWERPC] Adapt ipic driver to new host_ops interface, add set_irq_type to set IRQ sense
[POWERPC] back up old school ipic.[hc] to arch/ppc
[POWERPC] Use mpc8641hpcn PIC base address from dev tree.
[POWERPC] Allow MPC8641 HPCN to build with CONFIG_PCI disabled too.
[POWERPC] Fix powerpc 44x_mmu build
[POWERPC] Remove flush_dcache_all export
This fixes a hang on ppc32.
The problem was that I was comparing a 32-bit quantity with a 64-bit
quantity, and consequently time wasn't advancing. This makes us use a
64-bit quantity on all platforms, which ends up simplifying the code
since we can now get rid of the tb_last_stamp variable (which actually
fixes another bug that Ben H and I noticed while going carefully through
the code).
This works fine on my G4 tibook. Let me know how it goes on your
machines.
Acked-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eran Ben-Avi <eranpublic@yahoo.com> pointed out that the arch/ppc version
of smp_generic_take_timebase disables interrupts on entry but exits without
restoring them. However, both it and the arch/powerpc version have another
problem, which is that they use local_irq_disable/enable rather than
local_irq_save/restore, and they are called with interrupts disabled.
This fixes both problems; it changes a return to a break in the arch/ppc
version, and changes both versions to use local_irq_save/restore.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a problem introduced in 5db9fa9593.
The last_jiffy per-cpu variable is only 32 bits on 32-bit machines, but it
was being compared with a 64-bit quantity (tb_next_jiffy), which resulted in
time not advancing.
This fixes it by changing last_jiffy to be 64 bits on all platforms. With
this, we no longer need tb_last_stamp as a 32-bit version of tb_last_jiffy,
so this gets rid of tb_last_stamp and we just use tb_last_jiffy instead.
This also fixes a bug when the boot cpu is not online, because using
tb_last_stamp could have caused the wrong timebase origin value to be used
when calculating the time of day.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This code got moved from head.S but the copyright notice on head.S didn't
get transferred with it. Noticed by Cort Dougan <cort@fsmlabs.com>.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This problem was noticed by one of the Phyp firmware folks.
Our ibm,client-architecture-support call was failing.
This corrects the vector length parameters being passed in.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Device-tree bugs on js20 with some versions of SLOF were causing the
interrupt for IDE to not be parsed correctly and fail to boot. This
patch adds a bit more sanity checking to the parser to detect some of
those errors and fail instead of returning bogus information. The
powerpc PCI code can then trigger a fallback that works on those
machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When reworking the powerpc irq code, I figured out that we were using
the radix tree in a racy way. As a temporary fix, I put a spinlock in
there. However, this can have a significant impact on performances. This
patch reworks that to use a smarter technique based on the fact that
what we need is in fact a rwlock with extremely rare writers (thus
optimized for the read path).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Removes the flush_dcache_all export for non coherent platforms.
We removed the last in-kernel user of this years ago in arch/ppc
so it no longer serves a purpose. Plus, it breaks the build
at the moment.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Compile fails without defining CONFIG_PCI.
The patch fix this.
[paulus@samba.org: Moved of_irq_pci_swizzle so we only need one #ifdef]
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we get an illegal instruction exception, we check to see whether
the instruction is one that we emulate for the user program. Some of
the masks we use in checking whether the offending instruction is one
we care about didn't have the top bit set, which is the MSB of the
major opcode. Thus some undefined opcodes could get emulated as other
(defined but unimplemented) instructions. This corrects the masks.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch passes the UPIO_TSI flag to general 8259 serial driver
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are two problems in the powerpc gettimeofday code which can
cause incorrect results to be returned.
The first is that there is a race between do_gettimeofday and the
timer interrupt:
1. do_gettimeofday does get_tb()
2. decrementer exception on boot cpu which runs timer_recalc_offset,
which also samples the timebase and updates the do_gtod structure
with a greater timebase value.
3. do_gettimeofday calls __do_gettimeofday, which leads to the
negative result from tb_val - temp_varp->tb_orig_stamp.
The second is caused by taking the boot cpu offline, which can cause
the value of tb_last_jiffy to be increased past the currently
available timebase, causing the same underflow as above.
[paulus@samba.org - define and use data_barrier() instead of mb().]
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clear HID0[en_attn] at CPU init time on PPC970. Closes CVE-2006-4093.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code for using the radix tree for reverse mapping of interrupts has
a typo that causes it to create incorrect mappings if the software and
hardware numbers happen to be different. This would, among others, cause
the IDE interrupt to fail on js20's. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- On archs that have no-exec support, we vmalloc() a executable scratch
area of PAGE_SIZE and divide it up into an array of slots of maximum
instruction size for that arch
- On a kprobe registration, the original instruction is copied to the
first available free slot, so if multiple kprobes are registered, chances
are, they get contiguous slots
- On POWER4, due to not having coherent icaches, we could hit a situation
where a probe that is registered on one processor, is hit immediately on
another. This second processor could have fetched the stream of text from
the out-of-line single-stepping area *before* the probe registration
completed, possibly due to an earlier (and a different) kprobe hit and
hence would see stale data at the slot.
Executing such an arbitrary instruction lead to a problem as reported
in LTC bugzilla 23555.
The correct solution is to call flush_icache_range() as soon as the
instruction is copied for out-of-line single-stepping, so the correct
instruction is seen on all processors.
Thanks to Will Schmidt who tracked this down.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To compile kexec on 32-bit we need a few more bits and pieces. Rather
than add empty definitions, we can make crash.c work on 32-bit, with
only a couple of kludges.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We're missing a few functions for kexec to compile on 32-bit. There's
nothing really 64-bit specific about the 64-bit versions, so make them
generic rather than adding empty definitions for 32-bit.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the case of a system hang, the user will invoke soft-reset to
initiate the kdump boot. If xmon is enabled, the CPU(s) enter into the
xmon debugger. Unfortunately, the secondary CPU(s) will return to the
hung state when they exit from the debugger (returned from die() ->
system_reset_exception()). This causes a problem in kdump since the
hung CPU(s) will not respond to the IPI sent from kdump. This patch
fixes the issue by calling crash_kexec_secondary() directly from
system_reset_exception() without returning to the previous state. These
secondary CPUs wait 5ms until the kdump boot is started by the primary
CPU. In the case we exited from the debugger to "recover" (command 'x'
in xmon) the primary and the secondary CPUs will all return from die()
-> system_reset_exception() ->crash_kexec_secondary() wait 5ms, then
return to the previous state. A kdump boot is not started in this case.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously the message was "Fatal exception: panic_on_oops", as introduced
in a recent patch whith removed a somewhat dangerous call to ssleep() in
the panic_on_oops path. However, Paul Mackerras suggested that this was
somewhat confusing, leadind people to believe that it was panic_on_oops
that was the root cause of the fatal exception. On his suggestion, this
patch changes the message to simply "Fatal exception". A suitable oops
message should already have been displayed.
Signed-off-by: Simon Horman <horms@verge.net.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Noticing the following might_sleep warning (dump_stack()) during kdump
testing when CONFIG_DEBUG_SPINLOCK_SLEEP is enabled. All secondary CPUs
will be calling rtas_set_indicator with interrupts disabled to remove
them from global interrupt queue.
BUG: sleeping function called from invalid context at
arch/powerpc/kernel/rtas.c:463
in_atomic():1, irqs_disabled():1
Call Trace:
[C00000000FFFB970] [C000000000010234] .show_stack+0x68/0x1b0 (unreliable)
[C00000000FFFBA10] [C000000000059354] .__might_sleep+0xd8/0xf4
[C00000000FFFBA90] [C00000000001D1BC] .rtas_busy_delay+0x20/0x5c
[C00000000FFFBB20] [C00000000001D8A8] .rtas_set_indicator+0x6c/0xcc
[C00000000FFFBBC0] [C000000000048BF4] .xics_teardown_cpu+0x118/0x134
[C00000000FFFBC40] [C00000000004539C]
.pseries_kexec_cpu_down_xics+0x74/0x8c
[C00000000FFFBCC0] [C00000000002DF08] .crash_ipi_callback+0x15c/0x188
[C00000000FFFBD50] [C0000000000296EC] .smp_message_recv+0x84/0xdc
[C00000000FFFBDC0] [C000000000048E08] .xics_ipi_dispatch+0xf0/0x130
[C00000000FFFBE50] [C00000000009EF10] .handle_IRQ_event+0x7c/0xf8
[C00000000FFFBF00] [C0000000000A0A14] .handle_percpu_irq+0x90/0x10c
[C00000000FFFBF90] [C00000000002659C] .call_handle_irq+0x1c/0x2c
[C00000000058B9C0] [C00000000000CA10] .do_IRQ+0xf4/0x1a4
[C00000000058BA50] [C0000000000044EC] hardware_interrupt_entry+0xc/0x10
--- Exception: 501 at .plpar_hcall_norets+0x14/0x1c
LR = .pseries_dedicated_idle_sleep+0x190/0x1d4
[C00000000058BD40] [C00000000058BDE0] 0xc00000000058bde0 (unreliable)
[C00000000058BDF0] [C00000000001270C] .cpu_idle+0x10c/0x1e0
[C00000000058BE70] [C000000000009274] .rest_init+0x44/0x5c
To fix this issue, rtas_set_indicator_fast() is added so that will not
wait for RTAS 'busy' delay and this new function is used for kdump (in
xics_teardown_cpu()) and for CPU hotplug ( xics_migrate_irqs_away() and
xics_setup_cpu()).
Note that the platform architecture spec says that set-indicator
on the indicator we're using here is not permitted to return the
busy or extended busy status codes.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Minor comment fix for misc_64.S
[POWERPC] Use H_CEDE on non-SMT
[POWERPC] force 64bit mode in fwnmi handlers to workaround firmware bugs
[POWERPC] PMAC_APM_EMU should depend on ADB_PMU
[POWERPC] Fix new interrupt code (MPIC detection)
[POWERPC] Fix new interrupt code (MPIC endianness)
[POWERPC] Add cpufreq support for Xserve G5
[POWERPC] Xserve G5 thermal control fixes
[POWERPC] Fix mem= handling when the memory limit is > RMO size
[POWERPC] More offb/bootx fixes
[POWERPC] Fix legacy_serial.c error handling on 32 bits
[POWERPC] Fix default clock for udbg_16550
[POWERPC] Fix non-MPIC CHRPs with CONFIG_SMP set
[POWERPC] Fix 32 bits warning in prom_init.c
[POWERPC] Workaround Pegasos incorrect ISA "ranges"
[POWERPC] fix up front-LED Kconfig
The latest toolchains can produce a new ELF section in DSOs and
dynamically-linked executables. The new section ".gnu.hash" replaces
".hash", and allows for more efficient runtime symbol lookups by the
dynamic linker. The new ld option --hash-style={sysv|gnu|both} controls
whether to produce the old ".hash", the new ".gnu.hash", or both. In some
new systems such as Fedora Core 6, gcc by default passes --hash-style=gnu
to the linker, so that a standard invocation of "gcc -shared" results in
producing a DSO with only ".gnu.hash". The new ".gnu.hash" sections need
to be dealt with the same way as ".hash" sections in all respects; only the
dynamic linker cares about their contents. To work with older dynamic
linkers (i.e. preexisting releases of glibc), a binary must have the old
".hash" section. The --hash-style=both option produces binaries that a new
dynamic linker can use more efficiently, but an old dynamic linker can
still handle.
The new section runs afoul of the custom linker scripts used to build vDSO
images for the kernel. On ia64, the failure mode for this is a boot-time
panic because the vDSO's PT_IA_64_UNWIND segment winds up ill-formed.
This patch addresses the problem in two ways.
First, it mentions ".gnu.hash" in all the linker scripts alongside ".hash".
This produces correct vDSO images with --hash-style=sysv (or old tools),
with --hash-style=gnu, or with --hash-style=both.
Second, it passes the --hash-style=sysv option when building the vDSO
images, so that ".gnu.hash" is not actually produced. This is the most
conservative choice for compatibility with any old userland. There is some
concern that some ancient glibc builds (though not any known old production
system) might choke on --hash-style=both binaries. The optimizations
provided by the new style of hash section do not really matter for a DSO
with a tiny number of symbols, as the vDSO has. If someone wants to use
=gnu or =both for their vDSO builds and worry less about that
compatibility, just change the option and the linker script changes will
make any choice work fine.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Few of the callback functions and notifier blocks that are associated with cpu
notifications incorrectly have __devinit and __devinitdata. They should be
__cpuinit and __cpuinitdata instead.
It makes no functional difference but wastes text area when CONFIG_HOTPLUG is
enabled and CONFIG_HOTPLUG_CPU is not.
This patch fixes all those instances.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is part of an effort to unify the panic_on_oops behaviour across
all architectures that implement it.
It was pointed out to me by Andi Kleen that if an oops has occured in
interrupt context, then calling sleep() in the oops path will only cause a
panic, and that it would be really better for it not to be in the path at
all.
This patch removes the ssleep() call and reworks the console message
accordinly. I have a slght concern that the resulting console message is
too long, feedback welcome.
For powerpc it also unifies the 32bit and 64bit behaviour.
Fror x86_64, this patch only updates the console message, as ssleep() is
already not present.
Signed-off-by: Horms <horms@verge.net.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A minor comment fix for misc_64.S from Takao Shinohara.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The firmware of POWER4 and JS20 systems does not switch the cpu to 64bit
mode when the registered system_reset and machine_check handlers get called.
If a 32bit process runs on that cpu at the time of the event, the cpu
remains in 32bit mode. xmon and kdump can not deal with it, the result is
an error like 'Bad kernel stack pointer fff2aad0 at 3200'.
xmon just loses some register info, but booting the kdump kernel usually fails.
Both handlers are not hot paths. Duplicate the EXCEPTION_PROLOG_PSERIES macro
and add two instructions to switch to 64bit:
li r11,5;
rldimi r10,r11,61,0;
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code in legacy_serial.c wouldn't properly compare OF translation
results against OF_BAD_ADDR as it's using a phys_addr_t which is 32
bits on some 32-bit powerpc platforms. This fixes it by always using
a u64 which is what is returned by the OF parsing routines. It also
makes translation failure harmless for ISA serial ports. If they
can't translate, we can't use the UART early, but we can still let the
8250 driver use it later on by using IO port accessors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes it possible to provide 0 as the clock value for
udbg_16550, making it default to the standard 1.8432Mhz clock
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Pseudo-CHRP machines like Pegasos without an MPIC would crash at boot if
CONFIG_SMP was set because the "smp_ops" pointer was set to MPIC related
ops unconditionally. This patch makes it NULL on machines that don't
support SMP and provides proper default behaviour in the callers when
smp_ops is NULL.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A warning is hurting my eyes when building 32 bits kernels
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Pegasos firmware doesn't create a valid "ranges" property for the
ISA bridge, thus causing translation of ISA addresses and IO ports to
fail. This fixes it, thus re-enabling proper early serial console to
work on Pegasos.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a bit of boundchecking in the new Open Firmware interrupt
tree parsing code. It's important that it fails when things aren't correct in
order to trigger fallback mecanisms that are necessary to make some machines
work properly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch slightly reworks the new irq code to fix a small design error. I
removed the passing of the trigger to the map() calls entirely, it was not a
good idea to have one call do two different things. It also fixes a couple of
corner cases.
Mapping a linux virtual irq to a physical irq now does only that. Setting the
trigger is a different action which has a different call.
The main changes are:
- I no longer call host->ops->map() for an already mapped irq, I just return
the virtual number that was already mapped. It was called before to give an
opportunity to change the trigger, but that was causing issues as that could
happen while the interrupt was in use by a device, and because of the
trigger change, map would potentially muck around with things in a racy way.
That was causing much burden on a given's controller implementation of
map() to get it right. This is much simpler now. map() is only called on
the initial mapping of an irq, meaning that you know that this irq is _not_
being used. You can initialize the hardware if you want (though you don't
have to).
- Controllers that can handle different type of triggers (level/edge/etc...)
now implement the standard irq_chip->set_type() call as defined by the
generic code. That means that you can use the standard set_irq_type() to
configure an irq line manually if you wish or (though I don't like that
interface), pass explicit trigger flags to request_irq() as defined by the
generic kernel interfaces. Also, using those interfaces guarantees that
your controller set_type callback is called with the descriptor lock held,
thus providing locking against activity on the same interrupt (including
mask/unmask/etc...) automatically. A result is that, for example, MPIC's
own map() implementation calls irq_set_type(NONE) to configure the hardware
to the default triggers.
- To allow the above, the irq_map array entry for the new mapped interrupt
is now set before map() callback is called for the controller.
- The irq_create_of_mapping() (also used by irq_of_parse_and_map()) function
for mapping interrupts from the device-tree now also call the separate
set_irq_type(), and only does so if there is a change in the trigger type.
- While I was at it, I changed pci_read_irq_line() (which is the helper I
would expect most archs to use in their pcibios_fixup() to get the PCI
interrupt routing from the device tree) to also handle a fallback when the
DT mapping fails consisting of reading the PCI_INTERRUPT_PIN to know wether
the device has an interrupt at all, and the the PCI_INTERRUPT_LINE to get an
interrupt number from the device. That number is then mapped using the
default controller, and the trigger is set to level low. That default
behaviour works for several platforms that don't have a proper interrupt
tree like Pegasos. If it doesn't work for your platform, then either
provide a proper interrupt tree from the firmware so that fallback isn't
needed, or don't call pci_read_irq_line()
- Add back a bit that got dropped by my main rework patch for properly
clearing pending IPIs on pSeries when using a kexec
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
screen_info.h doesn't have anything to do with the tty layer and shouldn't be
included by tty.h. This patches removes the include and modifies all users to
directly include screen_info.h. struct screen_info is mainly used to
communicate with the console drivers in drivers/video/console. Note that this
patch touches every arch and I have no way of testing it. If there is a
mistake the worst thing that will happen is a compile error.
[akpm@osdl.org: fix arm build]
[akpm@osdl.org: fix alpha build]
Signed-off-by: Jon Smirl <jonsmir@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: add defconfig for Freescale MPC8349E-mITX board
powerpc: Add base support for the Freescale MPC8349E-mITX eval board
Documentation: correct values in MPC8548E SEC example node
[POWERPC] Actually copy over i8259.c to arch/ppc/syslib this time
[POWERPC] Add new interrupt mapping core and change platforms to use it
[POWERPC] Copy i8259 code back to arch/ppc
[POWERPC] New device-tree interrupt parsing code
[POWERPC] Use the genirq framework
[PATCH] genirq: Allow fasteoi handler to retrigger disabled interrupts
[POWERPC] Update the SWIM3 (powermac) floppy driver
[POWERPC] Fix error handling in detecting legacy serial ports
[POWERPC] Fix booting on Momentum "Apache" board (a Maple derivative)
[POWERPC] Fix various offb and BootX-related issues
[POWERPC] Add a default config for 32-bit CHRP machines
[POWERPC] fix implicit declaration on cell.
[POWERPC] change get_property to return void *
At the moment, powerpc and s390 have their own versions of do_softirq which
include local_bh_disable() and __local_bh_enable() calls. They end up
calling __do_softirq (in kernel/softirq.c) which also does
local_bh_disable/enable.
Apparently the two levels of disable/enable trigger a warning from some
validation code that Ingo is working on, and he would like to see the outer
level removed. But to do that, we have to move the account_system_vtime
calls that are currently in the arch do_softirq() implementations for
powerpc and s390 into the generic __do_softirq() (this is a no-op for other
archs because account_system_vtime is defined to be an empty inline
function on all other archs). This patch does that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Accurate hard-IRQ-flags and softirq-flags state tracing.
This allows us to attach extra functionality to IRQ flags on/off
events (such as trace-on/off).
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds the new irq remapper core and removes the old one. Because
there are some fundamental conflicts with the old code, like the value
of NO_IRQ which I'm now setting to 0 (as per discussions with Linus),
etc..., this commit also changes the relevant platform and driver code
over to use the new remapper (so as not to cause difficulties later
in bisecting).
This patch removes the old pre-parsing of the open firmware interrupt
tree along with all the bogus assumptions it made to try to renumber
interrupts according to the platform. This is all to be handled by the
new code now.
For the pSeries XICS interrupt controller, a single remapper host is
created for the whole machine regardless of how many interrupt
presentation and source controllers are found, and it's set to match
any device node that isn't a 8259. That works fine on pSeries and
avoids having to deal with some of the complexities of split source
controllers vs. presentation controllers in the pSeries device trees.
The powerpc i8259 PIC driver now always requests the legacy interrupt
range. It also has the feature of being able to match any device node
(including NULL) if passed no device node as an input. That will help
porting over platforms with broken device-trees like Pegasos who don't
have a proper interrupt tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Adds new routines to prom_parse to walk the device-tree for interrupt
information. This includes both direct mapping of interrupts and low
level parsing functions for use with partial trees.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adapts the generic powerpc interrupt handling code, and all of
the platforms except for the embedded 6xx machines, to use the new
genirq framework.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously we weren't checking for failures in translating device
addresses from the firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
