The current code assumes that we will always have at least 2 rx rings, 1
will be used as an aggregation ring for TPA and jumbo page placements.
However, it is possible, especially on a VF, that there is only 1 rx
ring available. In this scenario, the current code will fail to initialize.
To handle it, we need to properly set up only 1 ring without aggregation.
Set a new flag BNXT_FLAG_NO_AGG_RINGS for this condition and add logic to
set up the chip to place RX data linearly into a single buffer per packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the added support for the bnxt_re RDMA driver, both drivers can be
allocating completion rings in any order. The firmware does not know
which completion ring should be receiving async events. Add an
extra step to tell firmware the completion ring number for receiving
async events after bnxt_en allocates the completion rings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly support TX rate limiting in SRIOV VF functions or
NPAR functions, firmware needs better control over tx ring allocations.
The new scheme requires the driver to reserve the number of tx rings
and to query to see if the requested number of tx rings is reserved.
The driver will use the new scheme when the firmware interface spec is
1.6.1 or newer.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accept ipv6 flows in .ndo_rx_flow_steer() and support ETHTOOL_GRXCLSRULE
ipv6 flows.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing hardware RFS mode uses one hardware RSS context block
per ring just to calculate the RSS hash. This is very wasteful and
prevents VF functions from using it. The new hardware mode shares
the same hardware RSS context for RSS placement and RFS steering.
This allows VFs to enable RFS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function bnxt_rfs_supported() that determines if the chip supports
RFS. Refactor the existing function bnxt_rfs_capable() that determines
if run-time conditions support RFS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new vnic RSS capability will enhance NTUPLE support, to be added
in subsequent patches.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call tcp_gro_complete() in the common code path instead of the chip-
specific method. The newer 5731x method is missing the call.
Signed-off-by: Michael Chan <michael.chan@broadcmo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The advertising field is closely related to the auto_link_speeds field.
The former is the user setting while the latter is the firmware setting.
Both should be u16. We should use the advertising field in
bnxt_get_link_ksettings because the auto_link_speeds field may not
be updated with the latest from the firmware yet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IRQ is disabled by writing to the completion ring doorbell. This
should be done before the hardware completion ring is freed for correctness.
The current code disables IRQs after all the completion rings are freed.
Fix it by calling bnxt_disable_int_sync() before freeing the completion
rings. Rearrange the code to avoid forward declaration.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For better busy polling and GRO support. Do not re-arm IRQ if
napi_complete_done() returns false.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use native NAPI polling instead. The next patch will complete the work
by switching to use napi_complete_done()
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the network driver and RDMA driver operate on the same PCI function,
we need to create an interface to allow the RDMA driver to share resources
with the network driver.
1. Create a new bnxt_en_dev struct which will be returned by
bnxt_ulp_probe() upon success. After that, all calls from the RDMA driver
to bnxt_en will pass a pointer to this struct.
2. This struct contains additional function pointers to register, request
msix, send fw messages, register for async events.
3. If the RDMA driver wants to enable RDMA on the function, it needs to
call the function pointer bnxt_register_device(). A ulp_ops structure
is passed for RCU protected upcalls from bnxt_en to the RDMA driver.
4. The RDMA driver can call firmware APIs using the bnxt_send_fw_msg()
function pointer.
5. 1 stats context is reserved when the RDMA driver registers. MSIX
and completion rings are reserved when the RDMA driver calls
bnxt_request_msix() function pointer.
6. When the RDMA driver calls bnxt_unregister_device(), all RDMA resources
will be cleaned up.
v2: Fixed 2 uninitialized variable warnings.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver register function with firmware consists of passing version
information and registering for async events. To support the RDMA driver,
the async events that we need to register may change. Separate the
driver register function into 2 parts so that we can just update the
async events for the RDMA driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device supports RDMA, we'll setup network default rings so that
there are enough minimum resources for RDMA, if possible. However, the
user can still increase network rings to the max if he wants. The actual
RDMA resources won't be reserved until the RDMA driver registers.
v2: Fix compile warning when BNXT_CONFIG_SRIOV is not set.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All available remaining completion rings not used by the PF should be
made available for the VFs so that there are enough rings in the VF to
support RDMA. The earlier workaround code of capping the rings by the
statistics context is removed.
When SRIOV is disabled, call a new function bnxt_restore_pf_fw_resources()
to restore FW resources. Later on we need to add some logic to account
for RDMA resources.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that MSIX is enabled in bnxt_init_one(), resources may be allocated by
the RDMA driver before the network device is opened. So we cannot do
function reset in bnxt_open() which will clear all the resources.
The proper place to do function reset now is in bnxt_init_one().
If we get AER, we'll do function reset as well.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To better support the new RDMA driver, we need to move pci_enable_msix()
from bnxt_open() to bnxt_init_one(). This way, MSIX vectors are available
to the RDMA driver whether the network device is up or down.
Part of the existing bnxt_setup_int_mode() function is now refactored into
a new bnxt_init_int_mode(). bnxt_init_int_mode() is called during
bnxt_init_one() to enable MSIX. The remaining logic in
bnxt_setup_int_mode() to map the IRQs to the completion rings is called
during bnxt_open().
v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By refactoring existing code into this new function. The new function
will be used in subsequent patches.
v2: Fixed compile warning when CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function bnxt_hwrm_stat_ctx_alloc() always returns 0, even if the call
to _hwrm_send_message() fails. It may be better to propagate the errors
to the caller of bnxt_hwrm_stat_ctx_alloc().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188661
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support only IEEE DCBX initially. Add IEEE DCBNL ops and functions to
get and set the hardware DCBX parameters. The DCB code is conditional on
Kconfig CONFIG_BNXT_DCB.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest interface has the latest DCB command structs. Get and store the
max number of lossless TCs the hardware can support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function bnxt_setup_mq_tc() to handle MQPRIO. This new function
will be called during ETS setup when we add DCBNL in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When busy polling while a link is down (during a link-flap test), TX
timeouts were observed as well as the following messages in the ring
buffer:
bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51
bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free tx failed. rc:-1
bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51
bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free rx failed. rc:-1
These were resolved by checking for link status and returning if link
was not up.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Rob Miller <rob.miller@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing that:
#define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_VXLAN (0x1UL << 0)
#define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_GENEVE (0x5UL << 0)
and that 'bnxt_hwrm_tunnel_dst_port_alloc()' is only called with one of
these 2 constants, the TUNNEL_DST_PORT_ALLOC_REQ_TUNNEL_TYPE_GENEVE can not
trigger.
Replace the bit test that overlap by an equality test, just as in
'bnxt_hwrm_tunnel_dst_port_free()' above.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing synchronize_net() call to avoid potential use after free,
since we explicitly call napi_hash_del() to factorize the RCU grace
period.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newer chips have proper support for 4-tuple UDP RSS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some dual port NICs, the speed setting on one port can affect the
available speed on the other port. Add logic to detect these changes
and adjust the advertised speed settings when necessary.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new FORCE_LINK_DWN bit to shutdown link during close.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic is missing the check on whether the tx and rx rings are sharing
completion rings or not.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is automatically done from netif_napi_add(), and we want to not
export napi_hash_add() anymore in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: min_mtu 60, max_mtu 9000/1500
bnxt: min_mtu 60, max_mtu 9000
bnx2x: min_mtu 46, max_mtu 9600
- Fix up ETH_OVREHEAD -> ETH_OVERHEAD while we're in here, remove
duplicated defines from bnx2x_link.c.
bnx2: min_mtu 46, max_mtu 9000
- Use more standard ETH_* defines while we're at it.
bcm63xx_enet: min_mtu 46, max_mtu 2028
- compute_hw_mtu was made largely pointless, and thus merged back into
bcm_enet_change_mtu.
b44: min_mtu 60, max_mtu 1500
CC: netdev@vger.kernel.org
CC: Michael Chan <michael.chan@broadcom.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
CC: Siva Reddy Kallam <siva.kallam@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_hwrm_fw_set_time() now returns -EOPNOTSUPP when built for kernel
without RTC_LIB. Setting the firmware time is not critical to the
successful completion of the firmware update process.
Signed-off-by: Rob Swindell <Rob.Swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After generating the random MAC address for VF, call the firmware to
approve it. This step serves 2 purposes. Some hypervisor (e.g. ESX)
wants to approve the MAC address. 2nd, the call will setup the
proper forwarding database in the internal switch.
We need to unlock the hwrm_cmd_lock mutex before calling bnxt_approve_mac().
We can do that because we are at the end of the function and all the
previous firmware response data has been copied.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-arrange the code so that the generation of the random MAC address for
the VF is at the end of the function. The next patch will add one more step
to call bnxt_approve_mac() to get the firmware to approve the random MAC
address.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using Ethtool flashdev command, entire NVM package (*.pkg) files
may now be staged into the "update" area of the NVM and subsequently
verified and installed by the firmware using the newly introduced
command: NVM_INSTALL_UPDATE.
We also introduce use of the new firmware command FW_SET_TIME so that the
NVM-resident package installation log contains valid time-stamps.
Signed-off-by: Rob Swindell <Rob.Swindell@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove "Single-port/Dual-port" from the device names. Dual-port devices
will appear as 2 separate devices, so no need to call each a dual-port
device. Use a more generic name for VF devices belonging to the same
chip fanmily. Add some remaining NPAR device IDs.
Signed-off-by: David Christensen <david.christensen@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And remove redundant definitions of the same flags.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a code path where we are calling __iowrite64_copy() on
an address that is not 64-bit aligned. This causes an exception on
some architectures such as arm64. Fix that code path by using
__iowrite32_copy().
Reported-by: JD Zheng <jiandong.zheng@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5741X/5731X NPAR device IDs and dual media SFP/10GBase-T device IDs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are not enough resources to enable ntuple filtering,
log a warning message.
v2: Use single message and add missing newline.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the destination MAC address in the ntuple filter structure. The
current code assumes that the destination MAC address is always the MAC
address of the NIC. This may not be true if there are macvlans, for
example. Add destination MAC address checking and configure the filter
correctly using the correct index for the destination MAC address.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
txr->dev_state was not consistently manipulated with the acquisition of
the per-queue lock, after further inspection the lock does not seem
necessary, either the value is read as BNXT_DEV_STATE_CLOSING or 0.
Reported-by: coverity (CID 1339583)
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bridge device in NS2 has the same device ID as the ethernet controller.
Add check to avoid probing the bridge device.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate special vnic for dropping packets not matching the RX filters.
First vnic is for normal RX packets and the driver will drop all
packets on the 2nd vnic.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
