Min and max output ranges of regulators need to satisfy board
requirements not PMIC requirements. Thus adjust device tree to
cope with this.
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-7-claudiu.beznea@microchip.com
Min and max output ranges of regulators need to satisfy board
requirements not PMIC requirements. Thus adjust device tree to
cope with this.
Fixes: 5d4c3cfb63 ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-5-claudiu.beznea@microchip.com
On SAMA7G5, when resuming from backup and self-refresh, the bootloader
performs DDR PHY recalibration by restoring the value of ZQ0SR0 (stored
in RAM by Linux before going to backup and self-refresh). It has been
discovered that the current procedure doesn't work for all possible values
that might go to ZQ0SR0 due to hardware bug. The workaround to this is to
avoid storing some values in ZQ0SR0. Thus Linux will read the ZQ0SR0
register and cache its value in RAM after processing it (using
modified_gray_code array). The bootloader will restore the processed value.
Fixes: d2d4716d83 ("ARM: at91: pm: save ddr phy calibration data to securam")
Suggested-by: Frederic Schumacher <frederic.schumacher@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-4-claudiu.beznea@microchip.com
It has been discovered that on some parts, from time to time, self-refresh
procedure doesn't work as expected. Debugging and investigating it proved
that disabling AC DLL introduce glitches in RAM controllers which
leads to unexpected behavior. This is confirmed as a hardware bug. DLL
bypass disables 3 DLLs: 2 DX DLLs and AC DLL. Thus, keep only DX DLLs
disabled. This introduce 6mA extra current consumption on VDDCORE when
switching to any ULP mode or standby mode but the self-refresh procedure
still works.
Fixes: f0bbf17958 ("ARM: at91: pm: add self-refresh support for sama7g5")
Suggested-by: Frederic Schumacher <frederic.schumacher@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-3-claudiu.beznea@microchip.com
Don't just print a warning. Clean up and return an error as well.
Fixes: c834963932 ("net: lan966x: Add FDMA functionality")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/YwjgDm/SVd5c1tQU@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When running `ethtool -p` with the old management firmware,
the management firmware resource is not correctly released,
which causes firmware related malfunction: all the access
to management firmware hangs.
It releases the management firmware resource when set id
mode operation is not supported.
Fixes: ccb9bc1dfa ("nfp: add 'ethtool --identify' support")
Signed-off-by: Gao Xiao <gao.xiao@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20220829101651.633840-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stefan Schmidt says:
====================
ieee802154 for net 2022-08-29
- repeated word fix from Jilin Yuan.
- missed return code setting in the cc2520 driver by Li Qiong.
- fixing a potential race in by defering the workqueue destroy
in the adf7242 driver by Lin Ma.
- fixing a long standing problem in the mac802154 rx path to match
corretcly by Miquel Raynal.
* tag 'ieee802154-for-net-2022-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
ieee802154: cc2520: add rc code in cc2520_tx()
net: mac802154: Fix a condition in the receive path
net/ieee802154: fix repeated words in comments
ieee802154/adf7242: defer destroy_workqueue call
====================
Link: https://lore.kernel.org/r/20220829100308.2802578-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The same GPIO line can be shared by multiple phys for the coma mode pin.
If that is the case then, all the other phys that share the same line
will failed to be probed because the access to the gpio line is not
non-exclusive.
Fix this by making access to the gpio line to be nonexclusive using flag
GPIOD_FLAGS_BIT_NONEXCLUSIVE. This allows all the other PHYs to be
probed.
Fixes: 738871b092 ("net: phy: micrel: add coma mode GPIO")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220830064055.2340403-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TCP_FIN_WAIT2 and TCP_LAST_ACK were not handled, the connection is closing
so we can ignore them and avoid printing the "unhandled state"
warning message.
[ 1298.852386] nvmet_tcp: queue 2 unhandled state 5
[ 1298.879112] nvmet_tcp: queue 7 unhandled state 5
[ 1298.884253] nvmet_tcp: queue 8 unhandled state 5
[ 1298.889475] nvmet_tcp: queue 9 unhandled state 5
v2: Do not call nvmet_tcp_schedule_release_queue(), just ignore
the fin_wait2 and last_ack states.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There's a goto missing in nvmet_setup_auth(), causing a kernel oops
when nvme_auth_extract_key() fails.
Reported-by: Tal Lossos <tallossos@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Lexar NM610 reports bogus eui64 values that appear to be the same across
all drives. Quirk them out so they are not marked as "non globally unique"
duplicates.
Signed-off-by: Shyamin Ayesh <me@shyamin.com>
[patch formatting]
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In some cases of failure (dialect mismatches) in SMB2_negotiate(), after
the request is sent, the checks would return -EIO when they should be
rather setting rc = -EIO and jumping to neg_exit to free the response
buffer from mempool.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
When doing insert range and collapse range we should be
writing out the cached pages for the ranges affected but not
the whole file.
Fixes: c3a72bb213 ("smb3: Move the flush out of smb2_copychunk_range() into its callers")
Cc: stable@vger.kernel.org
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Not all the gfx10 variants need to integrate
global tap_delay and per se tap_delay firmwares
Only init tap_delay ucode when it does include in
rlc ucode binary so driver doesn't send a null buffer
to psp for firmware loading
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On secondary display hotplug we switch primary
stream from ODM2to1 to ODMBypass mode. Current
logic will trigger disabling front end for this
stream.
[How]
We need to check if prev_odm_pipe is equal to NULL
in order to disable dangling planes in this scenario.
Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Function wasn't returning false when it had a no stream
[HOW]
Made it return false when it had no stream.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Ethan Wellenreiter <Ethan.Wellenreiter@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pipes get merged in preparation for SubVP but if they don't get used, and
are in ODM or some other multi pipe config, it would calculate the
voltage level with a viewport of just one pipe from when they were split
resulting in too low of a voltage level.
[How]
Made it so that the viewport and other timing settings get rebuilt and re-
initialized after the pipe merge, before calculating the voltage level so it
would calculate it correctly.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Ethan Wellenreiter <Ethan.Wellenreiter@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
plane and stream variables used for cursor size allocation calculation
were stale from previous iteration. Redo the iteration to find the
correct cursor plane for the calculation.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Devices with CPU XGMI iolink do not support PCIe peer access.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To suppress the warning about version mismatch with
the latest 78.54.0 PMFW.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For those SMU13.0.7 unsecure SKUs, the vbios carried pptable is ready to go.
Use that one instead of hardcoded softpptable.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For some SMU13.0.0 SKUs, the vbios carried pptable is ready to go.
Use that one instead of hardcoded softpptable.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
fw version check was for release branch.
for staging, it has a chance to enter wrong code path.
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
When calculating allocation for cursor size, get the real cursor through
the HUBP instead of using the maximum cursor size for more optimal
allocation
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
When using a 4k monitor when cursor caching is not supported due to
framebuffer being on an uncacheable address, enabling display refresh
from MALL would trigger corruption if SS is enabled.
Prevent entering SS if we are on the edge case and cursor caching is not
possible. Do this only if cursor size larger than a 64x64@4bpp. Pull the
cursor size calculation out of if condition since cursor address may not
be set on all platforms
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For calculating cursor size allocation, surface size was used, resulting
in over allocation
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Number of encoder is set to 4 but only 3 instances are created.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Leo Chen <sancchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DIG_FIFO_ERROR = 1 caused mst daisy chain 2nd monitor black.
[How]
We need to set dig fifo read start level = 7 before dig fifo reset during dig
fifo enable according to hardware designer's suggestion. If it is zero, it will
cause underflow or overflow and DIG_FIFO_ERROR = 1.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Wang Fudong <Fudong.Wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In amdgpu_cs_ioctl, amdgpu_job_free could be performed ealier if there
is -ERESTARTSYS error. In this case, job->hw_fence could be not
initialized yet. Putting hw_fence during amdgpu_job_free could lead to a
use-after-free warning.
[How]
Check if drm_sched_job_init is performed before job_free by checking
s_fence.
v2: Check hw_fence.ops instead since it could be NULL if fence is not
initialized. Reverse the condition since !=NULL check is discouraged in
kernel.
Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When ODM is enabled, H timing control register reset
to 0. Div mode manual field get overwritten causing
no display on certain modes for dcn314.
[How]
Use REG_UPDATE instead of REG_SET to set div_mode
field.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Each index in the DPSTREAMCLK_CNTL register
phyiscally maps 1-to-1 with HPO stream encoder
instance. On the other hand, each index in
DTBCLK_P_CNTL physically maps 1-to-1 with OTG
instance.
Current DCN32 DPSTREAMCLK_CLK programing assumes
that OTG instance always maps 1-to-1 with
HPO stream encoder instance. This is not always
guaranteed and can result in blackscreen.
[How]
Program the correct dpstreamclk instance with
the correct dtbclk_p source.
Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New GFX11 MES FW adds the trap_en bit. For now hardcode to 1 (traps
enabled).
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Below driver load error will be printed, not friendly to end user.
amdgpu: ATOM BIOS: 113-D603GLXE-077
[drm] FRU: Failed to get size field
[drm:amdgpu_fru_get_product_info [amdgpu]] *ERROR* Failed to read FRU Manufacturer, ret:-5
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The alignment check in prepare_hugepage_range() is wrong for 2 GB
hugepages, it only checks for 1 MB hugepage alignment.
This can result in kernel crash in __unmap_hugepage_range() at the
BUG_ON(start & ~huge_page_mask(h)) alignment check, for mappings
created with MAP_FIXED at unaligned address.
Fix this by correctly handling multiple hugepage sizes, similar to the
generic version of prepare_hugepage_range().
Fixes: d08de8e2d8 ("s390/mm: add support for 2GB hugepages")
Cc: <stable@vger.kernel.org> # 4.8+
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add proper alignment for .nospec_call_table and .nospec_return_table in
vmlinux.
[hca@linux.ibm.com]: The problem with the missing alignment of the nospec
tables exist since a long time, however only since commit e6ed91fd07
("s390/alternatives: remove padding generation code") and with
CONFIG_RELOCATABLE=n the kernel may also crash at boot time.
The above named commit reduced the size of struct alt_instr by one byte,
so its new size is 11 bytes. Therefore depending on the number of cpu
alternatives the size of the __alt_instructions array maybe odd, which
again also causes that the addresses of the nospec tables will be odd.
If the address of __nospec_call_start is odd and the kernel is compiled
With CONFIG_RELOCATABLE=n the compiler may generate code that loads the
address of __nospec_call_start with a 'larl' instruction.
This will generate incorrect code since the 'larl' instruction only works
with even addresses. In result the members of the nospec tables will be
accessed with an off-by-one offset, which subsequently may lead to
addressing exceptions within __nospec_revert().
Fixes: f19fbd5ed6 ("s390: introduce execute-trampolines for branches")
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/8719bf1ce4a72ebdeb575200290094e9ce047bcc.1661557333.git.jpoimboe@kernel.org
Cc: <stable@vger.kernel.org> # 4.16
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The failing address alignment to HPAGE_MASK in do_exception(), for
hugetlb faults, was useless from the beginning. With 2 GB hugepage
support it became wrong, but w/o further negative impact. Now it
could have negative performance impact because it breaks the cacheline
optimization for process_huge_page().
Therefore, remove it.
Note that we still have failing address alignment by HW to PAGE_SIZE,
for all page faults, not just hugetlb faults. So this patch will not
fix UFFD_FEATURE_EXACT_ADDRESS for userfaultfd handling. It will just
move the failing address for hugetlb faults a bit closer to the real
address, at 4K page granularity, similar to normal page faults.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This reverts commit a8eb8e6f71 as
it can cause invalid link quality command sent to the firmware
and address the off-by-one issue by fixing condition of while loop.
Cc: stable@vger.kernel.org
Fixes: a8eb8e6f71 ("wifi: iwlegacy: 4965: fix potential off-by-one overflow in il4965_rs_fill_link_cmd()")
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220815073737.GA999388@wp.pl
Sometimes 'wilc_sdio_cmd53' is called with addresses pointing to an
object on the stack. Use dynamically allocated memory for cmd53 instead
of stack address which is not DMA'able.
Fixes: 5625f965d7 ("wilc1000: move wilc driver out of staging")
Reported-by: Michael Walle <mwalle@kernel.org>
Suggested-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Tested-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809075749.62752-1-ajay.kathat@microchip.com
_Read/Write_MACREG callbacks are NULL so the read/write_macreg_hdl()
functions don't do anything except free the "pcmd" pointer. It
results in a use after free. Delete them.
Fixes: 2865d42c78 ("staging: r8712u: Add the new driver to the mainline kernel")
Cc: stable <stable@kernel.org>
Reported-by: Zheng Wang <hackerzheng666@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Yw4ASqkYcUhUfoY2@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Since the commit 1227d2a20c ("bus: mhi: host: Move IRQ allocation to
controller registration phase"), the MHI context gets freed during
mhi_unregister_controller(). But when the MHI IRQs are shared, the IRQ
handler may get invoked during __free_irq() if CONFIG_DEBUG_SHIRQ is set.
In that case, there will be a null pointer dereference because of trying to
use the freed context struct.
So for fixing the issue, let's check for the existence of the context struct
at the start of the handler before handling the IRQ.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZ6VDKoFIy9ikWCeXVZ8R5v6RzvUFAmMM85YACgkQVZ8R5v6R
zvUAvAf+IHJBo3749kKBJ2YrD6+P1ZTXvcSD/UM2JUrAnRck6oUB1o75PJv0l+zJ
LG1FY6JzBFYT7tsJnbKEe92cEaYe6G5cnG0DM9fd3d90bnAKF+0TykiPbYWVmMNp
uv3ojQEd8q30SFF4xa83N51GFjlvyNEmy9gv+X6Ha3Wfa4LWLC5j5XNttz/052Zc
RE3uQvbygmWy/K3WlFqlTHESzMqlXrKs5gWTs2wilvIP0OhipSZ6haU4/sQKal+u
taEEOHz2ANQjInIbvohQTtnTnj5ZXS7S4tLz95RrZjh/VrG4O+HhQVwQUnxV4n1F
5CMLJXZgaMg+OJeBCkLWf+sFIHlgEQ==
=Zd1d
-----END PGP SIGNATURE-----
Merge tag 'mhi-fixes-for-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-linus
Manivannan writes:
"A single fix targeting the MHI host stack:
- Since the commit 1227d2a20c ("bus: mhi: host: Move IRQ allocation to
controller registration phase"), the MHI context gets freed during
mhi_unregister_controller(). But when the MHI IRQs are shared, the IRQ
handler may get invoked during __free_irq() if CONFIG_DEBUG_SHIRQ is set.
In that case, there will be a null pointer dereference because of trying to
use the freed context struct.
So for fixing the issue, let's check for the existence of the context struct
at the start of the handler before handling the IRQ."
* tag 'mhi-fixes-for-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi:
bus: mhi: host: Fix up null pointer access in mhi_irq_handler
Two minor fixes:
* cpu
- Fix use-after-free in adev_release()
* aspeed
- Fix error check for platform_get_irq()
-----BEGIN PGP SIGNATURE-----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=SUpA
-----END PGP SIGNATURE-----
Merge tag 'peci-fixes-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/iwi/linux into char-misc-linus
Iwona writes:
"PECI fixes for v6.0
Two minor fixes:
* cpu
- Fix use-after-free in adev_release()
* aspeed
- Fix error check for platform_get_irq()"
* tag 'peci-fixes-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/iwi/linux:
peci: cpu: Fix use-after-free in adev_release()
peci: aspeed: fix error check return value of platform_get_irq()
ISO OUT endpoint is enabled during queuing first usb request
in transfer ring and disabled when TRBERR is reported by controller.
After TRBERR and before next transfer added to TR driver must again
reenable endpoint but does not.
To solve this issue during processing TRBERR event driver must
set the flag EP_UPDATE_EP_TRBADDR in priv_ep->flags field.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062137.5766-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TRB_SMM flag indicates that DMA has completed the TD service with
this TRB. Usually it’s a last TRB in TD. In case of ISOC transfer for
bInterval > 1 each ISOC transfer contains more than one TD associated
with usb request (one TD per ITP). In such case the TRB_SMM flag will
be set in every TD and driver will recognize the end of transfer after
processing the first TD with TRB_SMM. In result driver stops updating
request->actual and returns incorrect actual length.
To fix this issue driver additionally must check TRB_CHAIN which is not
used for isochronous transfers.
Fixes: 249f0a25e8 ("usb: cdns3: gadget: handle sg list use case at completion correctly")
cc: <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220825062207.5824-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During cdrom emulation, the response to read_toc command must contain
the cdrom address as the number of sectors (2048 byte sized blocks)
represented either as an absolute value (when MSF bit is '0') or in
terms of PMin/PSec/PFrame (when MSF bit is set to '1'). Incase of
cdrom, the fsg_lun_open call sets the sector size to 2048 bytes.
When MAC OS sends a read_toc request with MSF set to '1', the
store_cdrom_address assumes that the address being provided is the
LUN size represented in 512 byte sized blocks instead of 2048. It
tries to modify the address further to convert it to 2048 byte sized
blocks and store it in MSF format. This results in data transfer
failures as the cdrom address being provided in the read_toc response
is incorrect.
Fixes: 3f565a363c ("usb: gadget: storage: adapt logic block size to bound block devices")
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/1661570110-19127-1-git-send-email-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Automatic kernel fuzzing revealed a recursive locking violation in
usb-storage:
============================================
WARNING: possible recursive locking detected
5.18.0 #3 Not tainted
--------------------------------------------
kworker/1:3/1205 is trying to acquire lock:
ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at:
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
but task is already holding lock:
ffff888018638db8 (&us_interface_key[i]){+.+.}-{3:3}, at:
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
...
stack backtrace:
CPU: 1 PID: 1205 Comm: kworker/1:3 Not tainted 5.18.0 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.13.0-1ubuntu1.1 04/01/2014
Workqueue: usb_hub_wq hub_event
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_deadlock_bug kernel/locking/lockdep.c:2988 [inline]
check_deadlock kernel/locking/lockdep.c:3031 [inline]
validate_chain kernel/locking/lockdep.c:3816 [inline]
__lock_acquire.cold+0x152/0x3ca kernel/locking/lockdep.c:5053
lock_acquire kernel/locking/lockdep.c:5665 [inline]
lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5630
__mutex_lock_common kernel/locking/mutex.c:603 [inline]
__mutex_lock+0x14f/0x1610 kernel/locking/mutex.c:747
usb_stor_pre_reset+0x35/0x40 drivers/usb/storage/usb.c:230
usb_reset_device+0x37d/0x9a0 drivers/usb/core/hub.c:6109
r871xu_dev_remove+0x21a/0x270 drivers/staging/rtl8712/usb_intf.c:622
usb_unbind_interface+0x1bd/0x890 drivers/usb/core/driver.c:458
device_remove drivers/base/dd.c:545 [inline]
device_remove+0x11f/0x170 drivers/base/dd.c:537
__device_release_driver drivers/base/dd.c:1222 [inline]
device_release_driver_internal+0x1a7/0x2f0 drivers/base/dd.c:1248
usb_driver_release_interface+0x102/0x180 drivers/usb/core/driver.c:627
usb_forced_unbind_intf+0x4d/0xa0 drivers/usb/core/driver.c:1118
usb_reset_device+0x39b/0x9a0 drivers/usb/core/hub.c:6114
This turned out not to be an error in usb-storage but rather a nested
device reset attempt. That is, as the rtl8712 driver was being
unbound from a composite device in preparation for an unrelated USB
reset (that driver does not have pre_reset or post_reset callbacks),
its ->remove routine called usb_reset_device() -- thus nesting one
reset call within another.
Performing a reset as part of disconnect processing is a questionable
practice at best. However, the bug report points out that the USB
core does not have any protection against nested resets. Adding a
reset_in_progress flag and testing it will prevent such errors in the
future.
Link: https://lore.kernel.org/all/CAB7eexKUpvX-JNiLzhXBDWgfg2T9e9_0Tw4HQ6keN==voRbP0g@mail.gmail.com/
Cc: stable@vger.kernel.org
Reported-and-tested-by: Rondreis <linhaoguo86@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YwkflDxvg0KWqyZK@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
