This patch changes the initial delay before the startup of a newly
scheduled isochronous stream. Currently the stream doesn't start
for at least 5 ms (40 microframes). This value is just an estimate;
it has no real justification.
Instead, we can start the stream as soon as possible after the
scheduling computations are complete. Essentially this requires
nothing more than reading the frame counter after the stream is
scheduled, instead of before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch continues the scheduling changes in ehci-hcd by adding a
table to store the bandwidth allocation below each TT. This will
speed up the scheduling code, as it will no longer need to read
through the entire schedule to compute the bandwidth currently in use.
Properly speaking, the FS/LS budget calculations should be done in
terms of full-speed bytes per microframe, as described in the USB-2
spec. However the driver currently uses microseconds per microframe,
and the scheduling code isn't robust enough at this point to change
over. For the time being, we leave the calculations as they are.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 476e4bf939.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 056ca85dab.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 19d3394304.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 86a63f1021.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 018258b436.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit fea0896fd3.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
This reverts commit 36a8758736.
Manjunath is no longer at Linaro, the email address bounces. Given
that, and the fact that others have reported problems with these
patches, I'm reverting them until someone from Linaro who can SUPPORT
THEM submits them.
I will no longer accept patches from linaro.com developers unless a
senior Linaro developer has signed off on them, which did not happen
with this patch set.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Currently, Samsung is using 'EXYNOS' as the name of Samsung SoCs.
Thus, ehci-exynos is preferred than ehci-s5p.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The non-DT for EXYNOS SoCs is not supported from v3.11.
Thus, there is no need to support non-DT for Exynos EHCI driver.
The 'include/linux/platform_data/usb-ehci-s5p.h' file has been
used for non-DT support. Thus, the 'usb-ehci-s5p.h' file can
be removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch significantly changes the scheduling code in ehci-hcd.
Instead of calculating the current bandwidth utilization by trudging
through the schedule and adding up the times used by the existing
transfers, we will now maintain a table holding the time used for each
of 64 microframes. This will drastically speed up the bandwidth
computations.
In addition, it eliminates a theoretical bug. An isochronous endpoint
may have bandwidth reserved even at times when it has no transfers
listed in the schedule. The table will keep track of the reserved
bandwidth, whereas adding up entries in the schedule would miss it.
As a corollary, we can keep bandwidth reserved for endpoints even
when they aren't in active use. Eventually the bandwidth will be
reserved when a new alternate setting is installed; for now the
endpoint's reservation takes place when its first URB is submitted.
A drawback of this approach is that transfers with an interval larger
than 64 microframes will have to be charged for bandwidth as though
the interval was 64. In practice this shouldn't matter much;
transfers with longer intervals tend to be rather short anyway (things
like hubs or HID devices).
Another minor drawback is that we will keep track of two different
period and phase values: the actual ones and the ones used for
bandwidth allocation (which are limited to 64). This adds only a
small amount of overhead: 3 bytes for each endpoint.
The patch also adds a new debugfs file named "bandwidth" to display
the information stored in the new table.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch begins the process of unifying the scheduling parameters
that ehci-hcd uses for interrupt and isochronous transfers. It
creates an ehci_per_sched structure, which will be stored in both
ehci_qh and ehci_iso_stream structures, and will contain the common
scheduling information needed for both.
Initially we merely create the new structure and move some existing
fields into it. Later patches will add more fields and utilize these
structures in improved scheduling algorithms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci-hcd is inconsistent in the sentinel values it uses to indicate
that no frame number has been assigned for a periodic transfer. Some
places it uses NO_FRAME (defined as 65535), other places it uses -1,
and elsewhere it uses 9999.
This patch defines a value for NO_FRAME which can fit in a 16-bit
signed integer, and changes the code to use it everywhere.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci-hcd uses a value of 0 in an endpoint's toggle flag to indicate
that the endpoint has been reset (and therefore the Data Toggle bit
needs to be cleared in the endpoint's QH overlay region).
The toggle flag should be set to 0 only when ehci_endpoint_reset()
succeeds. This patch moves the usb_settoggle() call into the
appropriate branch of the "if" statement.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scheduling code in ehci-hcd contains an error. For full-speed
isochronous-OUT transfers, the EHCI spec forbids scheduling
Start-Split transactions in H-microframe 7, but the driver allows it
anyway. This patch adds a check to prevent it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the bandwidth statistics maintained by ehci-hcd show up only
in the /sys/kernel/debug/usb/devices file, they ought to be calculated
correctly. The calculation for full-speed isochronous endpoints is
wrong; it mistakenly yields bytes per microframe instead of bytes per
frame. The "interval" value, which is in frames, should not be
converted to microframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check_intr_schedule() routine in ehci-hcd looks at the wrong
microframes when checking to see if a full-speed or low-speed
interrupt endpoint will fit in the periodic schedule. If the
Start-Split transaction is scheduled for microframe N then the
Complete-Split transactions get scheduled for microframes N+2, N+3, and
N+4. However the code considers N+1, N+2, and N+3 instead.
This patch fixes the limits on the "for" loop and also improves the
use of whitespace.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When devm_usb_get_phy() fails, usb_put_hcd() should be called
to prevent memory leak.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows MSM EHCI controller to be specified via device tree.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use struct usb_hcd::phy to hold USB PHY instance.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These aren't necessary after switch and if blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Clock tree support
- Clock management support using PM core
- Keystone config update for EMDA with ack from Vinod
- Enable SPI and I2C drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=d2uA
-----END PGP SIGNATURE-----
Merge tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc
From Santosh Shilimkar:
SOC updates for Keystone II devices:
- Clock tree support
- Clock management support using PM core
- Keystone config update for EMDA with ack from Vinod
- Enable SPI and I2C drivers
* tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: (510 commits)
ARM: keystone: Enable I2C and SPI bus support
ARM: keystone: Select TI_EDMA to be able to enable SPI driver
dma: Allow TI_EDMA selectable for ARCH_KEYSTONE
ARM: dts: keystone: Add the SPI nodes
ARM: dts: keystone: Add i2c device nodes
ARM: keystone: add PM domain support for clock management
ARM: keystone: Enable clock drivers
ARM: dts: keystone: Add clock phandle to UART nodes
ARM: dts: keystone: Add clock tree data to devicetree
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Haswell LynxPoint and LynxPoint-LP with the recent Intel BIOS show
mysterious wakeups after shutdown occasionally. After discussing with
BIOS engineers, they explained that the new BIOS expects that the
wakeup sources are cleared and set to D3 for all wakeup devices when
the system is going to sleep or power off, but the current xhci driver
doesn't do this properly (partly intentionally).
This patch introduces a new quirk, XHCI_SPURIOUS_WAKEUP, for
fixing the spurious wakeups at S5 by calling xhci_reset() in the xhci
shutdown ops as done in xhci_stop(), and setting the device to PCI D3
at shutdown and remove ops.
The PCI D3 call is based on the initial fix patch by Oliver Neukum.
[Note: Sarah changed the quirk name from XHCI_HSW_SPURIOUS_WAKEUP to
XHCI_SPURIOUS_WAKEUP, since none of the other quirks have system names
in them. Sarah also fixed a collision with a quirk submitted around the
same time, by changing the xhci->quirks bit from 17 to 18.]
This patch should be backported to kernels as old as 3.0, that
contain the commit 1c12443ab8 "xhci: Add
Lynx Point to list of Intel switchable hosts."
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The function pci_write_config_dword() sets the appropriate byteordering
internally so the value argument should not be converted to little-endian.
This bug was found by sparse.
This patch is not suitable for stable. Since cpu_to_lei32 is a no-op on
little endian systems, this bug would only affect big endian Intel
systems with the EHCI to xHCI port switchover, which are non-existent,
AFAIK.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
It has been reported that this chipset really cannot
sleep without this extraordinary delay.
This patch should be backported, in order to ensure this host functions
under stable kernels. The last quirk for Fresco Logic hosts (commit
bba18e33f2 "xhci: Extend Fresco Logic MSI
quirk.") was backported to stable kernels as old as 2.6.36.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The RWE bit of the USB 2.0 PORTPMSC register is supposed to enable
remote wakeup for devices in the lower power link state L1. It has
nothing to do with the device suspend remote wakeup from L2. The RWE
bit is designed to be set once (when USB 2.0 LPM is enabled for the
port) and cleared only when USB 2.0 LPM is disabled for the port.
The xHCI bus suspend method was setting the RWE bit erroneously, and the
bus resume method was clearing it. The xHCI 1.0 specification with
errata up to Aug 12, 2012 says in section 4.23.5.1.1.1 "Hardware
Controlled LPM":
"While Hardware USB2 LPM is enabled, software shall not modify the
HIRDBESL or RWE fields of the USB2 PORTPMSC register..."
If we have previously enabled USB 2.0 LPM for a device, that means when
the USB 2.0 bus is resumed, we violate the xHCI specification by
clearing RWE. It also means that after a bus resume, the host would
think remote wakeup is disabled from L1 for ports with USB 2.0 Link PM
enabled, which is not what we want.
This patch should be backported to kernels as old as 3.2, that
contain the commit 65580b4321 "xHCI: set
USB2 hardware LPM". That was the first kernel that supported USB 2.0
Link PM.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
In addition to the error statuses -ETIMEDOUT and -EPIPE, uhci_hub_control()
needs to return the length of copied buffer when appropriate, so that the
returned status of ->hub_control() in rh_call_control() in the USB core
HCD can be properly handled.
This patch also removes the OK() macro to make the code more readable.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that UHCI IO registers have been defined in uhci-hcd.h, use them.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-spear glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-spear suspend scenario.
Calling explicitly the ohci_suspend() routine in
spear_ohci_hcd_drv_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-sm501 glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly
handle ohci-sm501 suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_sm501_suspend() will ensure proper handling of suspend
scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-pxa27x glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly
handle ohci-pxa27x suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_hcd_pxa27x_drv_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-platform glue was not
properly handled as it was not suspending generic part
of ohci controller.Alan Stern suggested, properly handle
ohci-platform suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_platform_suspend() will ensure proper handling of
suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-omap glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-omap suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_omap_suspend() will ensure proper handling of suspend
scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-exynos glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-exynos suspend scenario.
Calling explicitly the ohci_suspend() routine in
exynos_ohci_suspend() will ensure proper handling of suspend
scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-ep93xx glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-ep93xx suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_hcd_ep93xx_drv_suspend() will ensure proper handling of
suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-da8xx glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-da8xx suspend scenario.
Calling explicitly the ohci_suspend()
routine in ohci_da8xx_suspend() will ensure proper
handling of suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-s3c2410 glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-s3c2410 suspend scenario.
Calling explicitly the ohci_suspend()
routine in ohci_hcd_s3c2410_drv_suspend() will ensure
proper handling of suspend scenario.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of ohci-at91 glue was not properly handled
as it was not suspending generic part of ohci controller. Alan Stern
suggested, properly handle ohci-at91 suspend scenario.
Calling explicitly the ohci_suspend() routine in ohci_hcd_at91_drv_suspend()
will ensure proper handling of suspend scenario. This task is sugested
by Alan Stern.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend scenario in case of OHCI was not properly
handled in ochi_suspend()routine. Alan Stern
suggested, properly handle OHCI suspend scenario.
This does generic proper handling of suspend
scenario to all OHCI SOC.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an implementation for hwahc_op_get_frame_number. The
request is fulfulled by forwarding it to the lower hcd. This was done
because the GET_TIME request on the HWA requires sending an URB to the
HWA and waiting for the results which cannot be done in atomic context.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "usb: pci-quirks: refactor AMD quirk to abstract AMD chipset types"
introduced a new AMD chipset type to filter AMD platforms with different
chipsets.
According to a recent thread [1], this patch updates SB800 prefetch routine
in AMD PLL quirk. And make it use the new chipset type to represent SB800
generation.
[1] http://marc.info/?l=linux-usb&m=138012321616452&w=2
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "usb: pci-quirks: refactor AMD quirk to abstract AMD chipset types"
introduced a new AMD chipset type to filter AMD platforms with different
chipsets.
According to a recent thread [1], this patch updates USB subsystem hang
symptom quirk which is observed on AMD all SB600 and SB700 revision
0x3a/0x3b. And make it use the new chipset type to represent.
[1] http://marc.info/?l=linux-usb&m=138012321616452&w=2
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_clk_get() is used so there is no reason to explicitly
call clk_put() in probe or remove functions.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for non-NULL overrides before dereferencing since platforms may
pass in NULL overrides.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of usb phy reinitialization:
e.g. insmod usb-module(usb works well) -> rmmod usb-module -> insmod usb-module
It found the PHY_CLK_VALID bit didn't work if it's not with the power-on reset.
So we just check PHY_CLK_VALID bit during the stage with POR, this can be met
by the tricky of checking FSL_SOC_USB_PRICTRL register.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For controller versions greater than 1.6, setting ULPI_PHY_CLK_SEL
bit when USB_EN bit is already set causes instability issues with
PHY_CLK_VLD bit. So USB_EN is set only for IP controller version
below 1.6 before setting ULPI_PHY_CLK_SEL bit
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the OHCI pxa27x/pxa3xx host controller driver from
ohci-hcd host code so that it can be built as a separate driver
module. This work is part of enabling multi-platform kernels on
ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the OHCI EP93XX host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the OHCI NXP host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Many place function name and struct name started with usb,
current scenario replaced usb with ohci for proper naming.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Samsung OHCI S3C24xx/S3C64xx host controller driver
from ohci-hcd host code so that it can be built as a separate
driver module.This work is part of enabling multi-platform.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the TI OHCI Atmel host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the ST OHCI SPEAr host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the TI OHCI OMAP3 host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the TI OHCI OMAP1/2 host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Samsung OHCI EXYNOS host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the W90X900(W90P910) on-chip host controller driver from
ehci-hcd host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM;
however, note that other changes are still needed before W90X900(W90P910)
can be booted with a multi-platform kernel
and an ehci driver that only works on one of them.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the w90X900 bus glue.
This patch is rebased on greghk/usb-next 3.12 rc1.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- add PLL for S3C64XX
- add s3c64xx clock driver
- update drivers to use CCF of s3c64xx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSQK8VAAoJEA0Cl+kVi2xql9IP/2ZdMukndE/gxZpsHCwKSFgm
pme2TxM4weN3q8c/749+r8AzwLl+RKbJdiw5DN4XDZ4cTdSSLkDkASUy0A0/r6Rg
147zoQSeI02HU9LgKzZP731x3wOOCAM+RdI3eT0idDSY14Z0cScNtp7tCU52BhEF
OdZtQTDHdcnZuESUVGksRq2GM4V2KxlzBB/FNEtq28edEQa8gXmEdpfM7AkTtl1M
e5JFmwY3xaL2qL/0A27trOyxsuyacx1K0GHWMaHeE6wpsVh3EzK2Bx/iHTcH1wre
MIplDMUj18QEziuUgZ82M7sJ/VPYDugplZTI1tMKgln8ri5AA5Wtvn8e6intMntc
f2VsZdOXlY0Uxz0SqGsLlxdMzi+rRy2HAlEuUKThQ8QMPxHB4uYKXjP1gZEskPwd
BSIJ7vXXoPxIHlC7f2PIMPRyqcgLrPG8Y+/1Obcl5pQTyP8am1throJWPlyPKEuv
yOqfuxfgZLXL1XJdcLDswgz+qRIPacbm7/1hM62wwGErjUo8m3wvmy88ZfR4Myo+
jj1avbsPthfInBl2/OMp9vGlZm6544SV7RtKU1/wuDNGPQba8+tr9FOiv7tJ2kRG
xnLRcop9lu4qNqykeJkxGsOfHmTvYjG4N7TSrHunKJpN6fuVOQR93V1RSRAEX5e9
TvEuCjm3OJj4J1sARwke
=bUyC
-----END PGP SIGNATURE-----
Merge tag 'samsung-clk-s3c64xx' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
From Kukjin Kim:
Common clk support for S3C64XX
- add PLL for S3C64XX
- add s3c64xx clock driver
- update drivers to use CCF of s3c64xx
* tag 'samsung-clk-s3c64xx' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Remove old clock management code
ARM: S3C64XX: Migrate clock handling to Common Clock Framework
usb: ohci-s3c2410.c: Use clk_prepare_enable/clk_disable_unprepare
ARM: S3C64XX: Use clk_prepare_enable/clk_disable_unprepare in dma.c
ARM: SAMSUNG: Add soc_is_s3c6400/s3c6410 macros
Signed-off-by: Olof Johansson <olof@lixom.net>
The following patch is required to resolve remote wake issues with
certain devices.
Issue description:
If the remote wake is issued from the device in a specific timing
condition while the system is entering sleep state then it may cause
system to auto wake on subsequent sleep cycle.
Root cause:
Host controller rebroadcasts the Resume signal > 100 µseconds after
receiving the original resume event from the device. For proper
function, some devices may require the rebroadcast of resume event
within the USB spec of 100µS.
Workaroud:
1. Filter the AMD platforms with Yangtze chipset, then judge of all the usb
devices are mouse or not. And get out the port id which attached a mouse
with Pixart controller.
2. Then reset the port which attached issue device during system resume
from S3.
[Q] Why the special devices are only mice? Would high speed devices
such as 3G modem or USB Bluetooth adapter trigger this issue?
- Current this sensitivity is only confined to devices that use Pixart
controllers. This controller is designed for use with LS mouse
devices only. We have not observed any other devices failing. There
may be a small risk for other devices also but this patch (reset
device in resume phase) will cover the cases if required.
[Q] Shouldn’t the resume signal be sent within 100 us for every
device?
- The Host controller may not send the resume signal within 100us,
this our host controller specification change. This is why we
require the patch to prevent side effects on certain known devices.
[Q] Why would clicking mouse INTENSELY to wake the system up trigger
this issue?
- This behavior is specific to the devices that use Pixart controller.
It is timing dependent on when the resume event is triggered during
the sleep state.
[Q] Is it a host controller issue or mouse?
- It is the host controller behavior during resume that triggers the
device incorrect behavior on the next resume.
This patch sets USB_QUIRK_RESET_RESUME flag for these Pixart-based mice
when they attached to platforms with AMD Yangtze chipset.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch abstracts out a AMD chipset type which includes southbridge
generation and its revision. When os excutes usb_amd_find_chipset_info
routine to initialize AMD chipset type, driver will know which kind of
chipset is used.
This update has below benifits:
- Driver is able to confirm which southbridge generations and their
revision are used, with chipset detection once.
- To describe chipset generations with enumeration types brings better
readability.
- It's flexible to filter AMD platforms to implement new quirks in future.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Andiry Xu <andiry.xu@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, chipidea host has already depended on USB_EHCI_HCD
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for specifying soft dependencies in the modules themselves was
introduced in commit 7cb14ba.
In Arch we have always been shipping a module.d(5) fragment ordering ohci/uhci
after ehci. If this ordering is really necessary, it would be great to move it
to the kernel and getting the correct fragment generated by depmod.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since uhci-hcd, ehci-hcd, and xhci-hcd support runtime PM, the .pm
field in their pci_driver structures should be protected by CONFIG_PM
rather than CONFIG_PM_SLEEP. The corresponding change has already
been made for ohci-hcd.
Without this change, controllers won't do runtime suspend if system
suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in ohci-hcd. The change is more
complicated than it was in ehci-hcd, because ohci-hcd doesn't scan for
isochronous completions in the same way as ehci-hcd does. Rather, it
depends on the hardware adding completed TDs to a "done queue". Some
OHCI controller don't handle this properly when a TD's time slot has
already expired, so we have to avoid adding such TDs to the schedule
in the first place. As a result, if the URB was submitted too late
then none of its TDs will get put on the schedule, so none of them
will end up on the done queue, so the driver will never realize that
the URB should be completed.
To solve this problem, the patch adds one to urb_priv->td_cnt for such
URBs, making it larger than urb_priv->length (td_cnt already gets set
to the number of TD's that had to be skipped because their slots have
expired). Each time an URB is given back, the finish_urb() routine
looks to see if urb_priv->td_cnt for the next URB on the same endpoint
is marked in this way. If so, it gives back the next URB right away.
This should be applied to all kernels containing commit 815fa7b917
(USB: OHCI: fix logic for scheduling isochronous URBs).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in uhci-hcd. It should be
applied to all kernels containing commit c44b225077 (UHCI: implement
new semantics for URB_ISO_ASAP).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
The same policy should be implemented in imx21-hcd, but I don't know
enough about the hardware to do it. As a second-best substitute, this
patch treats very late isochronous submissions as though the
URB_ISO_ASAP flag were set. I don't have any way to test this change,
unfortunately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The halted state of a endpoint cannot be cleared over CLEAR_HALT from a
user process, because the stopped_td variable was overwritten in the
handle_stopped_endpoint() function. So the xhci_endpoint_reset() function will
refuse the reset and communication with device can not run over this endpoint.
https://bugzilla.kernel.org/show_bug.cgi?id=60699
Signed-off-by: Florian Wolter <wolly84@web.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.
EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:
/* stop resume signaling */
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, status_reg);
clear_bit(wIndex, &ehci->resuming_ports);
retval = ehci_handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core. When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.
After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device. The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7. The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.
This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0. ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.
I attempted to replicate this bug with Ubuntu 12.04, but could not. I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with. I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.
Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)
Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.
This should also solve some weird behavior happening in command cancellation cases.
This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
http://marc.info/?l=linux-usb&m=136269803207465&w=2
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When a command times out, the command ring is first aborted,
and then stopped. If the command ring is empty when it is stopped
the stop event will point to next command which is not yet set.
xHCI tries to handle this next event often causing an oops.
Don't handle command completion events on stopped cmd ring if ring is
empty.
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Giovanni <giovanni.nervi@yahoo.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This reverts commit 3b8d7321ed, which
brings back commit 428aac8a81 as it should
be working for the 3.13-rc1 merge window now that Alan's other fixes are
here in the tree already.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have USB fixes now in Linus's tree that we need to properly sort out
with reverts and the like in the usb-next branch, so merge them together
and do it by hand.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's first set of fixes for v3.12-rc series, patches have
been soaking in linux-usb for a while now.
We have the usual sparse and build warnings, a Kconfig fix
to a mismerge on dwc3 Kconfig, fix for a possible memory leak
in dwc3, s3c-hsotg won't disconnect when bus goes idle, locking
fix in mv_u3d_core, endpoint disable fix in f_mass_storage.
We also have one device ID added to dwc3's PCI glue layer in order
to support Intel's BayTrail devices.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=51X+
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.12-rc2
Here's first set of fixes for v3.12-rc series, patches have
been soaking in linux-usb for a while now.
We have the usual sparse and build warnings, a Kconfig fix
to a mismerge on dwc3 Kconfig, fix for a possible memory leak
in dwc3, s3c-hsotg won't disconnect when bus goes idle, locking
fix in mv_u3d_core, endpoint disable fix in f_mass_storage.
We also have one device ID added to dwc3's PCI glue layer in order
to support Intel's BayTrail devices.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the iso_stream_schedule() routine in ehci-sched.c
to handle cases where an underrun causes an isochronous endpoint's
queue to empty out, but the client driver wants to maintain
synchronization with the device (i.e., the URB_ISO_ASAP flag is not
set). This could not happen until recently, when ehci-hcd switched
over to completing URBs in a tasklet.
(This may seem like an unlikely case to worry about, but underruns are
all too common with the snd-usb-audio driver, which doesn't use
URB_ISO_ASAP.)
As part of the fix, some URBs may need to be given back when they are
submitted. This is necessary when the URB's scheduled slots all fall
before the current value of ehci->last_iso_frame, and as an
optimization we do it also when the slots all fall before the current
frame number.
As a second part of the fix, we may need to skip some but not all of
an URB's packets. This is necessary when some of the URB's scheduled
slots fall before the current value of ehci->last_iso_frame and some
of them fall after the current frame number. A new field
(first_packet) is added to struct ehci_iso_sched, to indicate how many
packets should be skipped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch interchanges the "if" and "else" branches of the big "if"
statement in iso_stream_schedule(), in preparation for the next patch
in this series. That is, it changes
if (likely(!...)) {
A
} else {
B
}
to
if (unlikely(...)) {
B
} else {
A
}
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 428aac8a81.
This isn't quite ready for 3.12, we need some more EHCI driver changes
that are just now showing up. So revert this for now, and queue it up
later for 3.13.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local symbols used in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch modifies the ohci-s3c2410 driver to prepare and unprepare
clocks in addition to enabling and disabling, since it is required
by common clock framework.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlJJ8ACgkQMUfUDdst+ymBAwCgg8czTAuwpCCK7H8LHnC2BsMj
dtUAnjDisrbw4qWSXaaA/sfgSZjKW5G4
=Tman
-----END PGP SIGNATURE-----
Merge tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog"
* tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (352 commits)
usbcore: fix incorrect type in assignment in descriptors_changed()
usbcore: compare and release one bos descriptor in usb_reset_and_verify_device()
ehci: remove debugging statement with ehci statistics in ehci_stop()
ehci: remove duplicate debug_async_open() prototype in ehci-dbg.c
ehci: enable debugging code when CONFIG_DYNAMIC_DEBUG is set
ehci: remove ehci_vdbg() verbose debugging statements
Documentation sysfs-bus-usb: Document which files are used by libusb
Documentation sysfs-bus-usb: Document the speed file used by libusb
Documentation sysfs-bus-usb: Move files with known users to stable
USB: fix build error when CONFIG_PM_SLEEP isn't enabled
usb: r8a66597-hcd: use platform_{get,set}_drvdata()
usb: phy-tegra-usb: use platform_{get,set}_drvdata()
usb: acm gadget: Null termintate strings table
dma: cppi41: off by one in desc_to_chan()
xhci: Fix warning introduced by disabling runtime PM.
dev-core: fix build break when DEBUG is enabled
USB: OHCI: Allow runtime PM without system sleep
usb: ohci-at91: remove unnecessary dev_set_drvdata()
usb: renesas_usbhs: use platform_{get,set}_drvdata()
usb: fotg210-udc: use platform_{get,set}_drvdata()
...
This patch removes the ehci statictics information output in ehci_stop()
because they do not provide interesting info. At any case, the current
statistics can be viewed by reading the 'registers' file in debugfs.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the duplicate of debug_async_open() prototype following
three lines below the debug_async_open() declaration.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugging code for ehci is enabled to run if the DEBUG flag is defined.
This patch enables the debugging code also when the kernel is configured
with dynamic debugging on.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes ehci_vdbg debugging statements from EHCI host controller
driver because they produce too much information, lowering the signal to noise
ratio when debugging, and because they are not used anymore.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
This first patch should fix the build breakage Sedat Dilek reported.
Apologizes for not including this patch before commit
0730d52a86 "xhci:prevent "callbacks suppressed"
when debug is not enabled"
The second patch fixes a new build warning introduced by commit
c8476fb855 "usb: xhci: Disable runtime PM suspend
for quirky controllers", which was caught by the 0day build system.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=siJK
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-08-27-15-07' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Fix build breakage and new warnings.
Hi Greg,
This first patch should fix the build breakage Sedat Dilek reported.
Apologizes for not including this patch before commit
0730d52a86 "xhci:prevent "callbacks suppressed"
when debug is not enabled"
The second patch fixes a new build warning introduced by commit
c8476fb855 "usb: xhci: Disable runtime PM suspend
for quirky controllers", which was caught by the 0day build system.
Sarah Sharp
Since ohci-hcd supports runtime PM, the .pm field in its pci_driver
structure should be protected by CONFIG_PM rather than
CONFIG_PM_SLEEP.
Without this change, OHCI controllers won't do runtime suspend if
system suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When debug is not enabled and dev_dbg() will expand to nothing,
log might be flooded with "callbacks suppressed". If it was not
done on purpose, better to use dev_dbg_ratelimited() instead.
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Wrong capability bit was checked for best effort service latency.
bit 20 indicate port is BESL LPM capable (BLC),
bit 19 is hardware LPM capable (HLC)
This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdcc7 "usb: xhci:
add USB2 Link power management BESL support"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Steve Cotton <steve@s.cotton.clara.co.uk>
Cc: stable@vger.kernel.org
If a USB controller with XHCI_RESET_ON_RESUME goes to runtime suspend,
a reset will be performed upon runtime resume. Any previously suspended
devices attached to the controller will be re-enumerated at this time.
This will cause problems, for example, if an open system call on the
device triggered the resume (the open call will fail).
Note that this change is only relevant when persist_enabled is not set
for USB devices.
This patch should be backported to kernels as old as 3.0, that
contain the commit c877b3b2ad "xhci: Add
reset on resume quirk for asrock p67 host".
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Commit 9a11899c5e (USB: OHCI: add missing PCI PM callbacks to
ohci-pci.c) added missing ohci_suspend and ohci_resume callback
pointers, but forgot that these callbacks are declared and defined
only when CONFIG_PM is enabled.
This patch adds a preprocessor conditional to avoid build errors when
PM is disabled.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Meelis Roos <mroos@linux.ee>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7e8d5cd93f ("USB: Add EHCI support for MX27 and MX31 based
boards") introduced code that could potentially lead to a NULL pointer
dereference on driver removal.
Fix this by checking for the value of pdata before dereferencing it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org> # 2.6.33+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
