Commit Graph

349 Commits

Author SHA1 Message Date
Kelvin Cao 3df54c870f ntb_hw_switchtec: Allow using Switchtec NTB in multi-partition setups
Allow using Switchtec NTB in setups that have more than two partitions.
Note: this does not enable having multi-host communication, it only
allows for a single NTB link between two hosts in a network that might
have more than two.

Use following logic to determine the NT peer partition:

1) If there are 2 partitions, and the target vector is set in
   the Switchtec configuration, use the partition specified in target
   vector.
2) If there are 2 partitions and target vector is unset
   use the only other partition as specified in the NT EP map.
3) If there are more than 2 partitions and target vector is set
   use the other partition specified in target vector.
4) If there are more than 2 partitions and target vector is unset,
   this is invalid and report an error.

Signed-off-by: Kelvin Cao <kelvin.cao@microsemi.com>
[logang@deltatee.com: commit message fleshed out]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28 22:17:23 -05:00
Jon Mason 2dd0f6a64a NTB: switchtec_ntb: Add new line on appropriate printks
Trivial addition of "\n" to the dev_* prints where necessary

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28 22:17:23 -05:00
Colin Ian King c5ec8b451a NTB: switchtec_ntb: fix spelling mistake: "peforming" -> "performing"
Trivial fix to spelling mistake in dev_err error message

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-By: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28 22:17:23 -05:00
Dave Jiang 3f7756728e ntb: remove Intel Atom NTB driver support
Removing dead code since this is not being used.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28 22:17:23 -05:00
Greg Kroah-Hartman 0ed08f829b ntb: remove unneeded DRIVER_LICENSE #defines
There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.

This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference, especially when the string is defined just a few
lines above the usage of it.

Reported-and-reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: Gary R Hook <gary.hook@amd.com>
Cc: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28 22:17:23 -05:00
Doug Meyer 140eb52277 NTB: ntb_hw_switchtec: Fix peer BAR bug in switchtec_ntb_init_shared_mw
This resolves a bug which may incorrectly configure the peer host's
LUT for shared memory window access. The code was using the local
host's first BAR number, rather than the peer hosts's first BAR
number, to determine what peer NT control register to program.

The bug will cause the Switchtec NTB link to work only if both peers
have the same first NTB BAR configured. In all other configurations,
the link will not come up, failing silently.

When both hosts have the same first BAR, the configuration works only
because the first BAR numbers happent to be the same. When the hosts
do not have the same first BAR, then the LUT translation will not be
configured in the correct peer LUT and will not give the peer the
shared memory window access required for the link to operate.

Signed-off-by: Doug Meyer <dmeyer@gigaio.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: 678784a44ae8 ("NTB: switchtec_ntb: Initialize hardware for memory windows")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2018-01-28 22:17:22 -05:00
Kees Cook e99e88a9d2 treewide: setup_timer() -> timer_setup()
This converts all remaining cases of the old setup_timer() API into using
timer_setup(), where the callback argument is the structure already
holding the struct timer_list. These should have no behavioral changes,
since they just change which pointer is passed into the callback with
the same available pointers after conversion. It handles the following
examples, in addition to some other variations.

Casting from unsigned long:

    void my_callback(unsigned long data)
    {
        struct something *ptr = (struct something *)data;
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, ptr);

and forced object casts:

    void my_callback(struct something *ptr)
    {
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr);

become:

    void my_callback(struct timer_list *t)
    {
        struct something *ptr = from_timer(ptr, t, my_timer);
    ...
    }
    ...
    timer_setup(&ptr->my_timer, my_callback, 0);

Direct function assignments:

    void my_callback(unsigned long data)
    {
        struct something *ptr = (struct something *)data;
    ...
    }
    ...
    ptr->my_timer.function = my_callback;

have a temporary cast added, along with converting the args:

    void my_callback(struct timer_list *t)
    {
        struct something *ptr = from_timer(ptr, t, my_timer);
    ...
    }
    ...
    ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback;

And finally, callbacks without a data assignment:

    void my_callback(unsigned long data)
    {
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, 0);

have their argument renamed to verify they're unused during conversion:

    void my_callback(struct timer_list *unused)
    {
    ...
    }
    ...
    timer_setup(&ptr->my_timer, my_callback, 0);

The conversion is done with the following Coccinelle script:

spatch --very-quiet --all-includes --include-headers \
	-I ./arch/x86/include -I ./arch/x86/include/generated \
	-I ./include -I ./arch/x86/include/uapi \
	-I ./arch/x86/include/generated/uapi -I ./include/uapi \
	-I ./include/generated/uapi --include ./include/linux/kconfig.h \
	--dir . \
	--cocci-file ~/src/data/timer_setup.cocci

@fix_address_of@
expression e;
@@

 setup_timer(
-&(e)
+&e
 , ...)

// Update any raw setup_timer() usages that have a NULL callback, but
// would otherwise match change_timer_function_usage, since the latter
// will update all function assignments done in the face of a NULL
// function initialization in setup_timer().
@change_timer_function_usage_NULL@
expression _E;
identifier _timer;
type _cast_data;
@@

(
-setup_timer(&_E->_timer, NULL, _E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E->_timer, NULL, (_cast_data)_E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, &_E);
+timer_setup(&_E._timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, (_cast_data)&_E);
+timer_setup(&_E._timer, NULL, 0);
)

@change_timer_function_usage@
expression _E;
identifier _timer;
struct timer_list _stl;
identifier _callback;
type _cast_func, _cast_data;
@@

(
-setup_timer(&_E->_timer, _callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
 _E->_timer@_stl.function = _callback;
|
 _E->_timer@_stl.function = &_callback;
|
 _E->_timer@_stl.function = (_cast_func)_callback;
|
 _E->_timer@_stl.function = (_cast_func)&_callback;
|
 _E._timer@_stl.function = _callback;
|
 _E._timer@_stl.function = &_callback;
|
 _E._timer@_stl.function = (_cast_func)_callback;
|
 _E._timer@_stl.function = (_cast_func)&_callback;
)

// callback(unsigned long arg)
@change_callback_handle_cast
 depends on change_timer_function_usage@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
identifier _handle;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *t
 )
 {
(
	... when != _origarg
	_handletype *_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle;
	... when != _handle
	_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle;
	... when != _handle
	_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
)
 }

// callback(unsigned long arg) without existing variable
@change_callback_handle_cast_no_arg
 depends on change_timer_function_usage &&
                     !change_callback_handle_cast@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *t
 )
 {
+	_handletype *_origarg = from_timer(_origarg, t, _timer);
+
	... when != _origarg
-	(_handletype *)_origarg
+	_origarg
	... when != _origarg
 }

// Avoid already converted callbacks.
@match_callback_converted
 depends on change_timer_function_usage &&
            !change_callback_handle_cast &&
	    !change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier t;
@@

 void _callback(struct timer_list *t)
 { ... }

// callback(struct something *handle)
@change_callback_handle_arg
 depends on change_timer_function_usage &&
	    !match_callback_converted &&
            !change_callback_handle_cast &&
            !change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
@@

 void _callback(
-_handletype *_handle
+struct timer_list *t
 )
 {
+	_handletype *_handle = from_timer(_handle, t, _timer);
	...
 }

// If change_callback_handle_arg ran on an empty function, remove
// the added handler.
@unchange_callback_handle_arg
 depends on change_timer_function_usage &&
	    change_callback_handle_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
identifier t;
@@

 void _callback(struct timer_list *t)
 {
-	_handletype *_handle = from_timer(_handle, t, _timer);
 }

// We only want to refactor the setup_timer() data argument if we've found
// the matching callback. This undoes changes in change_timer_function_usage.
@unchange_timer_function_usage
 depends on change_timer_function_usage &&
            !change_callback_handle_cast &&
            !change_callback_handle_cast_no_arg &&
	    !change_callback_handle_arg@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type change_timer_function_usage._cast_data;
@@

(
-timer_setup(&_E->_timer, _callback, 0);
+setup_timer(&_E->_timer, _callback, (_cast_data)_E);
|
-timer_setup(&_E._timer, _callback, 0);
+setup_timer(&_E._timer, _callback, (_cast_data)&_E);
)

// If we fixed a callback from a .function assignment, fix the
// assignment cast now.
@change_timer_function_assignment
 depends on change_timer_function_usage &&
            (change_callback_handle_cast ||
             change_callback_handle_cast_no_arg ||
             change_callback_handle_arg)@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_func;
typedef TIMER_FUNC_TYPE;
@@

(
 _E->_timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-(_cast_func)_callback;
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-&_callback;
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-(_cast_func)_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
)

// Sometimes timer functions are called directly. Replace matched args.
@change_timer_function_calls
 depends on change_timer_function_usage &&
            (change_callback_handle_cast ||
             change_callback_handle_cast_no_arg ||
             change_callback_handle_arg)@
expression _E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_data;
@@

 _callback(
(
-(_cast_data)_E
+&_E->_timer
|
-(_cast_data)&_E
+&_E._timer
|
-_E
+&_E->_timer
)
 )

// If a timer has been configured without a data argument, it can be
// converted without regard to the callback argument, since it is unused.
@match_timer_function_unused_data@
expression _E;
identifier _timer;
identifier _callback;
@@

(
-setup_timer(&_E->_timer, _callback, 0);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0L);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0UL);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0L);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0UL);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0L);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0UL);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0L);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0UL);
+timer_setup(_timer, _callback, 0);
)

@change_callback_unused_data
 depends on match_timer_function_unused_data@
identifier match_timer_function_unused_data._callback;
type _origtype;
identifier _origarg;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *unused
 )
 {
	... when != _origarg
 }

Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-21 15:57:07 -08:00
Dave Jiang 4201a9918c ntb: intel: remove b2b memory window workaround for Skylake NTB
The workaround code is never used because Skylake NTB does not need it.

Reported-by: Allen Hubbe <allen.hubbe@dell.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18 20:54:47 -05:00
Bhumika Goyal 3a814a04e6 NTB: make idt_89hpes_cfg const
Make these const as they are only used during a copy operation.
Done using Coccinelle.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18 20:37:13 -05:00
Logan Gunthorpe 87d11e645e NTB: switchtec_ntb: Add memory window support
The Switchtec hardware has two types of memory windows: LUTs and Direct.
The first area in each BAR is for LUT windows and the remaining area is
for the direct region. The total number of LUT entries is set by a
configuration setting in hardware and they all must be the same
size. (This is fixed by switchtec_ntb to be 64K.)

switchtec_ntb enables the LUTs only for the first BAR and enables the
highest power of two possible. Seeing the LUTs are at the beginning of
the BAR, the direct memory window's alignment is affected. Therefore,
the maximum direct memory window size can not be greater than the number
of LUTs times 64K. The direct window in other BARs will not have this
restriction as the LUTs will not be enabled there. LUTs will only be
exposed through the NTB API if the use_lut_mw parameter is set.

Seeing the Switchtec hardware, by default, configures BARs to be 4G a
module parameter is given to limit the size of the advertised memory
windows. Higher layers tend to allocate the maximum BAR size and this
has a tendency to fail when they try to allocate 4GB of contiguous
memory.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18 20:37:12 -05:00
Logan Gunthorpe b9a4acac28 NTB: switchtec_ntb: Implement scratchpad registers
Seeing there is no dedicated hardware for this, we simply add
these as entries in the shared memory window. Thus, we could support
any number of them but 128 seems like enough, for now.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18 20:37:12 -05:00
Logan Gunthorpe 6619bf9549 NTB: switchtec_ntb: Implement doorbell registers
Pretty straightforward implementation of doorbell registers.
The shift and mask were setup in an earlier patch and this just hooks
up the appropriate portion of the IDB register as the local doorbells
and the opposite portion of ODB as the peer doorbells. The DB mask is
protected by a spinlock to avoid concurrent read-modify-write accesses.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18 20:37:12 -05:00
Logan Gunthorpe 0ee28f26f3 NTB: switchtec_ntb: Add link management
switchtec_ntb checks for a link by looking at the shared memory
window. If the magic number is correct and the other side indicates
their link is enabled then we take the link to be up.

Whenever we change our local link status we send a msg to the
other side to check whether it's up and change their status.

The current status is maintained in a flag so ntb_is_link_up
can return quickly.

We utilize Switchtec's link status notifier to also check link changes
when the switch notices a port changes state.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18 20:37:12 -05:00
Logan Gunthorpe e099b45b7c NTB: switchtec_ntb: Add skeleton NTB driver
Add a skeleton NTB driver which will be filled out in subsequent patches.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18 20:37:12 -05:00
Logan Gunthorpe 3dd4db475c NTB: switchtec_ntb: Initialize hardware for doorbells and messages
Set up some hardware registers and creates interrupt service routines
for the doorbells and messages.

There are 64 doorbells in the switch that are shared between all
partitions. The upper 4 doorbells are also shared with the messages
and are therefore not used. Thus, this provides 28 doorbells for each
partition.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18 20:37:12 -05:00
Logan Gunthorpe ec0467ccbd NTB: switchtec_ntb: Initialize hardware for memory windows
Add the code to initialize the memory windows in the hardware.
This includes setting up the requester ID table, and figuring out
which BAR corresponds to which memory window. (Seeing the switch
can be configured with any number of BARs.)

Also, seeing the device doesn't have hardware for scratchpads or
determining the link status, we create a shared memory window that has
these features. A magic number with a version component will be used
to determine if the other side's driver is actually up.

The shared memory window also informs the other side of the
size and count of the local memory windows.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18 20:37:12 -05:00
Logan Gunthorpe 33dea5aae0 NTB: switchtec_ntb: Introduce initial NTB driver
Seeing the Switchtec NTB hardware shares the same endpoint as the
management endpoint we utilize the class_interface API to register
an NTB driver for every Switchtec device in the system that has the
NTB class code.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18 20:37:12 -05:00
Logan Gunthorpe 980c41c86b NTB: Ensure ntb_mw_get_align() is only called when the link is up
With Switchtec hardware it's impossible to get the alignment parameters
for a peer's memory window until the peer's driver has configured its
windows. Strictly speaking, the link doesn't have to be up for this,
but the link being up is the only way the client can tell that
the other side has been configured.

This patch converts ntb_transport and ntb_perf to use this function after
the link goes up. This simplifies these clients slightly because they
no longer have to store the alignment parameters. It also tweaks
ntb_tool so that peer_mw_trans will print zero if it is run before
the link goes up.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-11-18 20:37:11 -05:00
Dave Jiang f3fd2afed8 ntb: transport shouldn't disable link due to bogus values in SPADs
It seems that under certain scenarios the SPAD can have bogus values caused
by an agent (i.e. BIOS or other software) that is not the kernel driver, and
that causes memory window setup failure. This should not cause the link to
be disabled because if we do that, the driver will never recover again. We
have verified in testing that this issue happens and prevents proper link
recovery.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Fixes: 84f766855f ("ntb: stop link work when we do not have memory")
2017-08-01 13:31:44 -04:00
Logan Gunthorpe bc240eec4b ntb: use correct mw_count function in ntb_tool and ntb_transport
After converting to the new API, both ntb_tool and ntb_transport are
using ntb_mw_count to iterate through ntb_peer_get_addr when they
should be using ntb_peer_mw_count.

This probably isn't an issue with the Intel and AMD drivers but
this will matter for any future driver with asymetric memory window
counts.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Fixes: 443b9a14ec ("NTB: Alter MW API to support multi-ports devices")
2017-07-17 12:56:15 -04:00
Gary R Hook 32e0f5bfa5 ntb: Add error path/handling to Debug FS entry creation
If a failure occurs when creating Debug FS entries, unroll all of
the work that's been done.

Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:08 -04:00
Gary R Hook 8407dd6c16 ntb: Add more debugfs support for ntb_perf testing options
The ntb_perf tool uses module parameters to control the
characteristics of its test.  Enable the changing of these
options through debugfs, and eliminating the need to unload
and reload the module to make changes and run additional tests.

Add a new module parameter that forces the DMA channel
selection onto the same node as the NTB device (default: true).

 - seg_order: Size of the NTB memory window; power of 2.
 - run_order: Size of the data buffer; power of 2.
 - use_dma:   Use DMA or memcpy? Default: 0.
 - on_node:   Only use DMA channel(s) on the NTB node. Default: true.

Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:08 -04:00
Gary R Hook 0b93a6dbec ntb: Remove debug-fs variables from the context structure
The Debug FS entries manage themselves; we don't need to hang onto
them in the context structure.

Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:07 -04:00
Gary R Hook e9410ff810 ntb: Add a module option to control affinity of DMA channels
The DMA channel(s)/memory used to transfer data to an NTB device
may not be required to be on the same node as the device. Add a
module parameter that allows any candidate channel (aside from
node assocation) and allocated memory to be used.

Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:07 -04:00
Serge Semin bf2a952d31 NTB: Add IDT 89HPESxNTx PCIe-switches support
IDT 89HPESxNTx device series is PCIe-switches, which support
Non-Transparent bridging between domains connected to the device ports.
Since new NTB API exposes multi-port interface and messaging API, the
IDT NT-functions can be now supported in the kernel. This driver adds
the following functionality:
1) Multi-port NTB API to have information of possible NT-functions
activated in compliance with available device ports.
2) Memory windows of direct and look up table based address translation
with all possible combinations of BARs setup.
3) Traditional doorbell NTB API.
4) One-on-one messaging NTB API.

There are some IDT PCIe-switch setups, which must be done before any of
the NTB peers started. It can be performed either by system BIOS via
IDT SMBus-slave interface or by pre-initialized IDT PCIe-switch EEPROM:
1) NT-functions of corresponding ports must be activated using
SWPARTxCTL and SWPORTxCTL registers.
2) BAR0 must be configured to expose NT-function configuration
registers map.
3) The rest of the BARs must have at least one memory window
configured, otherwise the driver will just return an error.
Temperature sensor of IDT PCIe-switches can be also optionally
activated by BIOS or EEPROM.
(See IDT documentations for details of how the pre-initialization can
be done)

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:07 -04:00
Logan Gunthorpe 48ea02184a ntb_hw_intel: Style fixes: open code macros that just obfuscate code
As per a comments in [1] by Greg Kroah-Hartman, the ndev_* macros should
be cleaned up. This makes it more clear what's actually going on when
reading the code.

[1] http://www.spinics.net/lists/linux-pci/msg56904.html

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:07 -04:00
Logan Gunthorpe 0f9bfb979a ntb_hw_amd: Style fixes: open code macros that just obfuscate code
As per a comments in [1] by Greg Kroah-Hartman, the ndev_* macros should
be cleaned up. This makes it more clear what's actually going on when
reading the code.

[1] http://www.spinics.net/lists/linux-pci/msg56904.html

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:07 -04:00
Serge Semin bc3e49adc2 NTB: Add Messaging NTB API
Some IDT NTB-capable PCIe-switches have message registers to communicate with
peer devices. This patch adds new NTB API callback methods, which can be used
to utilize these registers functionality:
 ntb_msg_count(); - get number of message registers
 ntb_msg_inbits(); - get bitfield of inbound message registers status
 ntb_msg_outbits(); - get bitfield of outbound message registers status
 ntb_msg_read_sts(); - read the inbound and outbound message registers status
 ntb_msg_clear_sts(); - clear status bits of message registers
 ntb_msg_set_mask(); - mask interrupts raised by status bits of message
registers.
 ntb_msg_clear_mask(); - clear interrupts mask bits of message registers
 ntb_msg_read(midx, *pidx); - read message register with specified index,
additionally getting peer port index which data received from
 ntb_msg_write(midx, pidx); - write data to the specified message register
sending it to the passed peer device connected over a pidx port
 ntb_msg_event(); - notify driver context of a new message event

Of course there is hardware which doesn't support Message registers, so
this API is made optional.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:07 -04:00
Serge Semin d67288a395 NTB: Alter Scratchpads API to support multi-ports devices
Even though there is no any real NTB hardware, which would have both more
than two ports and Scratchpad registers, it is logically correct to have
Scratchpad API accepting a peer port index as well. Intel/AMD drivers utilize
Primary and Secondary topology to split Scratchpad between connected root
devices. Since port-index API introduced, Intel/AMD NTB hardware drivers can
use device port to determine which Scratchpad registers actually belong to
local and peer devices. The same approach can be used if some potential
hardware in future will be multi-port and have some set of Scratchpads.
Here are the brief of changes in the API:
 ntb_spad_count() - return number of Scratchpads per each port
 ntb_peer_spad_addr(pidx, sidx) - address of Scratchpad register of the
peer device with pidx-index
 ntb_peer_spad_read(pidx, sidx) - read specified Scratchpad register of the
peer with pidx-index
 ntb_peer_spad_write(pidx, sidx) - write data to Scratchpad register of the
peer with pidx-index

Since there is hardware which doesn't support Scratchpad registers, the
corresponding API methods are now made optional.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:07 -04:00
Serge Semin 443b9a14ec NTB: Alter MW API to support multi-ports devices
Multi-port NTB devices permit to share a memory between all accessible peers.
Memory Windows API is altered to correspondingly initialize and map memory
windows for such devices:
 ntb_mw_count(pidx); - number of inbound memory windows, which can be allocated
for shared buffer with specified peer device.
 ntb_mw_get_align(pidx, widx); - get alignment and size restriction parameters
to properly allocate inbound memory region.
 ntb_peer_mw_count(); - get number of outbound memory windows.
 ntb_peer_mw_get_addr(widx); - get mapping address of an outbound memory window

If hardware supports inbound translation configured on the local ntb port:
 ntb_mw_set_trans(pidx, widx); - set translation address of allocated inbound
memory window so a peer device could access it.
 ntb_mw_clear_trans(pidx, widx); - clear the translation address of an inbound
memory window.

If hardware supports outbound translation configured on the peer ntb port:
 ntb_peer_mw_set_trans(pidx, widx); - set translation address of a memory
window retrieved from a peer device
 ntb_peer_mw_clear_trans(pidx, widx); - clear the translation address of an
outbound memory window

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:07 -04:00
Serge Semin 4e8c11b7fd NTB: Alter link-state API to support multi-port devices
Multi-port devices permit the NTB connections between multiple domains,
so a local device can have NTB link being up with one peer and being
down with another. NTB link-state API is appropriately altered to return
a bitfield of the link-states between the local device and possible peers.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:07 -04:00
Serge Semin 1e5301196a NTB: Add indexed ports NTB API
There is some NTB hardware, which can combine more than just two domains
over NTB. For instance, some IDT PCIe-switches can have NTB-functions
activated on more than two-ports. The different domains are distinguished
by ports they are connected to. So the new port-related methods are added to
the NTB API:
 ntb_port_number() - return local port
 ntb_peer_port_count() - return number of peers local port can connect to
 ntb_peer_port_number(pdix) - return port number by it index
 ntb_peer_port_idx(port) - return port index by it number

Current test-drivers aren't changed much. They still support two-ports devices
for the time being while multi-ports hardware drivers aren't added.

By default port-related API is declared for two-ports hardware.
So corresponding hardware drivers won't need to implement it.

Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-07-06 11:30:07 -04:00
Allen Hubbe 88931ec3dc ntb: no sleep in ntb_async_tx_submit
Do not sleep in ntb_async_tx_submit, which could deadlock.
This reverts commit "8c874cc140d667f84ae4642bb5b5e0d6396d2ca4"

Fixes: 8c874cc140 ("NTB: Address out of DMA descriptor issue with NTB")
Reported-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@dell.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-06-19 14:24:41 -04:00
Dave Jiang 5eb449e15d ntb: ntb_hw_intel: Skylake doorbells should be 32bits, not 64bits
Fixing doorbell register length to 32bits per spec. On Skylake NTB, the
doorbell registers are 32bit write only registers. The source for the
doorbell is a 64bit register that shows the interrupt bits.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 783dfa6cc4 ("ntb: Adding Skylake Xeon NTB support")
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-06-19 14:24:41 -04:00
Logan Gunthorpe 8e8496e0e9 ntb_transport: fix bug calculating num_qps_mw
A divide by zero error occurs if qp_count is less than mw_count because
num_qps_mw is calculated to be zero. The calculation appears to be
incorrect.

The requirement is for num_qps_mw to be set to qp_count / mw_count
with any remainder divided among the earlier mws.

For example, if mw_count is 5 and qp_count is 12 then mws 0 and 1
will have 3 qps per window and mws 2 through 4 will have 2 qps per window.
Thus, when mw_num < qp_count % mw_count, num_qps_mw is 1 higher
than when mw_num >= qp_count.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-06-19 14:24:41 -04:00
Logan Gunthorpe cb827ee6cc ntb_transport: fix qp count bug
In cases where there are more mw's than spads/2-2, the mw count gets
reduced to match the limitation. ntb_transport also tries to ensure that
there are fewer qps than mws but uses the full mw count instead of
the reduced one. When this happens, the math in
'ntb_transport_setup_qp_mw' will get confused and result in a kernel
paging request bug.

This patch fixes the bug by reducing qp_count to the reduced mw count
instead of the full mw count.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-06-19 14:24:41 -04:00
Gary R Hook 94fc795454 ntb: Correct modinfo usage statement for ntb_perf
The order parameters are powers of 2; adjust the usage information
to use correct mathematical representations.

Signed-off-by: Gary R Hook <gary.hook@amd.com>
Fixes: 8a7b6a778a ("ntb: ntb perf tool")
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-06-19 14:24:41 -04:00
Dave Jiang 939ada5fb5 ntb: ntb_hw_intel: link_poll isn't clearing the pending status properly
On Skylake hardware, the link_poll isn't clearing the pending interrupt
bit.  Adding a new function for SKX that handles clearing of status bit the
right way.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 783dfa6c ("ntb: Adding Skylake Xeon NTB support")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-02-16 23:11:26 -05:00
Thomas VanSelus 8fcd0950c0 ntb_transport: Pick an unused queue
Fix typo causing ntb_transport_create_queue to select the first
queue every time, instead of using the next free queue.

Signed-off-by: Thomas VanSelus <tvanselus@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Fixes: fce8a7bb5 ("PCI-Express Non-Transparent Bridge Support")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-02-16 23:11:26 -05:00
Dave Jiang 9644347c52 ntb: ntb_perf missing dmaengine_unmap_put
In the normal I/O execution path, ntb_perf is missing a call to
dmaengine_unmap_put() after submission. That causes us to leak
unmap objects.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 8a7b6a77 ("ntb: ntb perf tool")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-02-16 23:11:26 -05:00
Allen Hubbe dd62245e73 NTB: ntb_transport: fix debugfs_remove_recursive
The call to debugfs_remove_recursive(qp->debugfs_dir) of the sub-level
directory must not be later than
debugfs_remove_recursive(nt_debugfs_dir) of the top-level directory.
Otherwise, the sub-level directory will not exist, and it would be
invalid (panic) to attempt to remove it.  This removes the top-level
directory last, after sub-level directories have been cleaned up.

Signed-off-by: Allen Hubbe <Allen.Hubbe@dell.com>
Fixes: e26a5843f ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2017-02-16 23:10:52 -05:00
Steve Wahl dfb7d24c5a ntb_transport: Remove unnecessary call to ntb_peer_spad_read
The results were previously ignored, anyway.

Signed-off-by: Steve Wahl <Steve.Wahl@dell.com>
Fixes: e26a5843f7
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-12-23 16:11:07 -05:00
Christophe JAILLET 28734e8f69 NTB: Fix 'request_irq()' and 'free_irq()' inconsistancy
'request_irq()' and 'free_irq()' should have the same 'dev_id'.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-12-23 16:11:03 -05:00
Dave Jiang 09e71a6f13 ntb: fix SKX NTB config space size register offsets
The offsets for the SZ registers are wrong. Updated.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Sandeep Mann <sandeep@purestorage.com>
Tested-by: Zachary Ross <zacharyx.ross@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-12-23 16:10:54 -05:00
Shyam Sundar S K b17faba03f ntb_transport: Limit memory windows based on available, scratchpads
When the underlying NTB H/W driver advertises more memory windows
than the number of scratchpads available to setup MW's, it is likely
that we may end up filling the remaining memory windows with garbage.
So to avoid that, lets limit the memory windows that transport driver
can setup based on the available scratchpads.

Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-12-23 16:10:35 -05:00
Shyam Sundar S K 872deb2103 NTB: Register and offset values fix for memory window
Due to incorrect limit and translation register values, NTB link was
going down when the memory window was setup. Made appropriate changes
as per spec.

Fix limit register values for BAR1, which was overlapping
with the BAR23 address.

Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-12-23 16:09:18 -05:00
Xiangliang Yu e5b0d2d1ba NTB: add support for hotplug feature
AMD NTB support hotplug under B2B mode. NTB will trigger link
up/down interrupt event when doing plug add/remove, this patch
implements the two interrupt event to support B2B hotplug function.

Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-12-23 16:09:15 -05:00
Dave Jiang 783dfa6cc4 ntb: Adding Skylake Xeon NTB support
The Skylake Xeon NTB hardware has made some changes to the register name,
offset, and the way doorbells work. Adding driver support for the new
hardware.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-12-23 16:09:10 -05:00
Dan Carpenter 819baf8859 ntb_perf: potential info leak in debugfs
This is a static checker warning, not something I'm desperately
concerned about.  But snprintf() returns the number of bytes that
would have been copied if there were space.  We really care about the
number of bytes that actually were copied so we should use scnprintf()
instead.

It probably won't overrun, and in that case we may as well just use
sprintf() but these sorts of things make static checkers and code
reviewers happier.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-11-13 16:48:30 -05:00
Dave Jiang 25ea9f2bf5 ntb: ntb_hw_intel: init peer_addr in struct intel_ntb_dev
The peer_addr member of intel_ntb_dev is not set, therefore when
acquiring ntb_peer_db and ntb_peer_spad we only get the offset rather
than the actual physical address. Adding fix to correct that.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-11-13 16:48:29 -05:00
Nicholas Mc Guire cdc08982a5 ntb: make DMA_OUT_RESOURCE_TO HZ independent
schedule_timeout_* takes a timeout in jiffies but the code currently is
passing in a constant which makes this timeout HZ dependent, so pass it
through msecs_to_jiffies() to fix this up.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-11-13 16:48:29 -05:00
Nicholas Mc Guire c0a88032ef ntb_transport: make DMA_OUT_RESOURCE_TO HZ independent
schedule_timeout_* takes a timeout in jiffies but the code currently is
passing in a constant which makes this timeout HZ dependent, so pass it
through msecs_to_jiffies() to fix this up.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-11-13 16:48:29 -05:00
Wei Yongjun 49b89de41f NTB: ntb_hw_intel: Fix typo in module parameter descriptions
Fix typo in module parameter descriptions.

Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-11-13 16:48:29 -05:00
Wei Yongjun cedecbc5e0 ntb_pingpong: Fix db_init parameter description
Fix 'db_init' parameter description.

Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-11-13 16:48:29 -05:00
Dave Jiang 72203572af ntb: add DMA error handling for RX DMA
Adding support on the rx DMA path to allow recovery of errors when
DMA responds with error status and abort all the subsequent ops.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: linux-ntb@googlegroups.com
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-08-08 08:11:42 +05:30
Dave Jiang 9cabc2691e ntb: add DMA error handling for TX DMA
Adding support on the tx DMA path to allow recovery of errors when
DMA responds with error status and abort all the subsequent ops.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: linux-ntb@googlegroups.com
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2016-08-08 08:11:42 +05:30
Allen Hubbe 95f1464f69 NTB: ntb_hw_intel: use local variable pdev
Clean up duplicated expression by replacing it with the equivalent local
variable pdev.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:34:13 -04:00
Allen Hubbe 4089527388 NTB: ntb_hw_intel: show BAR size in debugfs info
It will be useful to know the hardware configured BAR size to diagnose
issues with NTB memory windows.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:33:47 -04:00
Logan Gunthorpe 35539b54ac ntb_perf: clear link_is_up flag when the link goes down.
When the link goes down, the link_is_up flag did not return to
false. This could have caused some subtle corner case bugs
when the link goes up and down quickly.

Once that was fixed, there was found to be a race if the link was
brought down then immediately up. The link_cleanup work would
occasionally be scheduled after the next link up event. This would
cancel the link_work that was supposed to occur and leave ntb_perf
in an unusable state.

To fix this we get rid of the link_cleanup work and put the actions
directly in the link_down event.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:08 -04:00
Logan Gunthorpe 20572ee1c5 ntb_pingpong: Add a debugfs file to get the ping count
This commit adds a debugfs 'count' file to ntb_pingpong. This is so
testing with ntb_pingpong can be automated beyond just checking the
logs for pong messages.

The count file returns a number which increments every pong. The
counter can be cleared by writing a zero.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:07 -04:00
Logan Gunthorpe bfcaa39652 ntb_tool: Add link status and files to debugfs
In order to more successfully script with ntb_tool it's useful to
have a link file to check the link status so that the script
doesn't use the other files until the link is up.

This commit adds a 'link' file to the debugfs directory which reads
boolean (Y or N) depending on the link status. Writing to the file
change the link state using ntb_link_enable or ntb_link_disable.

A 'link_event' file is also provided so an application can block until
the link changes to the desired state. If the user writes a 1, it will
block until the link is up. If the user writes a 0, it will block until
the link is down.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:07 -04:00
Logan Gunthorpe 717146a2a8 ntb_tool: Postpone memory window initialization for the user
In order to make the interface closer to the raw NTB API, this commit
changes memory windows so they are not initialized on link up.
Instead, the 'peer_trans*' debugfs files are introduced. When read,
they return information provided by ntb_mw_get_range. When written,
they create a buffer and initialize the memory window. The
value written is taken as the requested size of the buffer (which
is then rounded for alignment). Writing a value of zero frees the buffer
and tears down the memory window translation. The 'peer_mw*' file is
only created once the memory window translation is setup by the user.

Additionally, it was noticed that the read and write functions for the
'peer_mw*' files should have checked for a NULL pointer.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:07 -04:00
Logan Gunthorpe 26dc638ae6 ntb_perf: Wait for link before running test
Instead of returning immediately with an error when the link is
down, wait for the link to come up (or the user sends a SIGINT).

This is to make scripting ntb_perf easier.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:07 -04:00
Logan Gunthorpe 58fd0f3b15 ntb_perf: Return results by reading the run file
Instead of having to watch logs, allow the results to be retrieved
by reading back the run file. This file will return "running" when
the test is running and nothing if no tests have been run yet.
It returns 1 line per thread, and will display an error message if the
corresponding thread returns an error.

With the above change, the pr_info calls that returned the results are
then changed to pr_debug calls.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:07 -04:00
Logan Gunthorpe da573eaa3a ntb_perf: Improve thread handling to increase robustness
This commit accomplishes a few things:

1) Properly prevent multiple sets of threads from running at once using
a mutex. Lots of race issues existed with the thread_cleanup.

2) The mutex allows us to ensure that threads are finished before
tearing down the device or module.

3) Don't use kthread_stop when the threads can exit by themselves, as
this is counter-indicated by the kthread_create documentation. Threads
now wait for kthread_stop to occur.

4) Writing to the run file now blocks until the threads are complete.
The test can then be safely interrupted by a SIGINT.

Also, while I was at it:

5) debugfs_run_write shouldn't return 0 in the early check cases as this
could cause debugfs_run_write to loop undesirably.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:06 -04:00
Logan Gunthorpe fd2ecd885b ntb_perf: Schedule based on time not on performance
When debugging performance problems, if some issue causes the ntb
hardware to be significantly slower than expected, ntb_perf will
hang requiring a reboot because it only schedules once every 4GB.

Instead, schedule based on jiffies so it will not hang the CPU if
the transfer is slow.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:06 -04:00
Logan Gunthorpe 19645a0771 ntb_transport: Check the number of spads the hardware supports
I'm working on hardware that currently has a limited number of
scratchpad registers and ntb_ndev fails with no clue as to why. I
feel it is better to fail early and provide a reasonable error message
then to fail later on.

The same is done to ntb_perf, but it doesn't currently require enough
spads to actually fail. I've also removed the unused SPAD_MSG and
SPAD_ACK enums so that MAX_SPAD accurately reflects the number of
spads used.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:06 -04:00
Logan Gunthorpe 8b71d28506 ntb_tool: Add memory window debug support
We allocate some memory window buffers when the link comes up, then we
provide debugfs files to read/write each side of the link.

This is useful for debugging the mapping when writing new drivers.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:06 -04:00
Logan Gunthorpe 4aae977721 ntb_perf: Allow limiting the size of the memory windows
On my system, dma_alloc_coherent won't produce memory anywhere
near the size of the BAR. So I needed a way to limit this.

It's pretty much copied straight from ntb_transport.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:06 -04:00
Dave Jiang a754a8fcaf NTB: allocate number transport entries depending on size of ring size
Currently we only allocate a fixed default number of descriptors for the tx
and rx side. We should dynamically resize it to the number of descriptors
resides in the transport rings. We should know the number of transmit
descriptors at initializaiton. We will allocate the default number of
descriptors for receive side and allocate additional ones when we know the
actual max entries for receive.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <allen.hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:21:05 -04:00
Logan Gunthorpe 625f0802e8 ntb_tool: BUG: Ensure the buffer size is large enough to return all spads
On hardware with 32 scratchpad registers the spad field in ntb tool
could chop off the end. The maximum buffer size is increased from
256 to 15 times the number or scratchpads.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:05:31 -04:00
Logan Gunthorpe c792eba12c ntb_tool: Fix infinite loop bug when writing spad/peer_spad file
If you tried to write two spads in one line, as per the example:

root@peer# echo '0 0x01010101 1 0x7f7f7f7f' > $DBG_DIR/peer_spad

then the CPU would freeze in an infinite loop.

This wasn't immediately obvious but 'pos' was not incrementing the
buffer, so after reading the second pair of values, 'pos' would once
again be 3 and it would re-read the second pair of values ad infinitum.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-08-05 10:05:31 -04:00
Allen Hubbe 4f1b50c3e3 NTB: Remove _addr functions from ntb_hw_amd
Kernel zero day testing warned about address space confusion.  A virtual
iomem address was used where a physical address is expected.  The
offending functions implement an optional part of the api, so they are
removed.  They can be added later, after testing.

Fixes: a1b3695820

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-03-26 11:44:33 -04:00
Dave Jiang 838850ee0b NTB: Fix incorrect clean up routine in ntb_perf
The clean up routine when we failed to allocate kthread is not cleaning
up all the threads, only the same one over and over again.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-03-21 19:28:30 -04:00
Dave Jiang ddc8f6feec NTB: Fix incorrect return check in ntb_perf
kthread_create_no_node() returns error pointers, never NULL. Fix check so
it handles error correctly.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-03-21 19:28:25 -04:00
Sudip Mukherjee 2572c7fb4e ntb: fix possible NULL dereference
kmalloc can fail and we should check for NULL before using the pointer
returned by kmalloc.

Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-03-17 20:52:15 -04:00
Dave Jiang ee5f750f1c ntb: add missing setup of translation window
The perf tool is missing the setup of translation window. Adding call to
setup the translation window for backed memory.

Signed-off-by: John Kading <john.kading@gd-ms.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-03-17 20:50:15 -04:00
Dave Jiang 84f766855f ntb: stop link work when we do not have memory
Instead of keep trying to go through the init routine when we aren't able
to allocate memory, we should just stop and go down.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-03-17 20:38:40 -04:00
Dave Jiang e902133162 ntb: stop tasklet from spinning forever during shutdown.
We can leave tasklet spinning forever if we disable the tasklet during
qp shutdown and the tasklets are still being kicked off. This hopefully
should avoid that race condition.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Alex Depoutovitch <alex@pernixdata.com>
Tested-by: Alex Depoutovitch <alex@pernixdata.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-03-17 20:38:40 -04:00
Arnd Bergmann 1985a88107 ntb: perf test: fix address space confusion
The ntb driver assigns between pointers an __iomem tokens, and
also casts them to 64-bit integers, which results in compiler
warnings on 32-bit systems:

drivers/ntb/test/ntb_perf.c: In function 'perf_copy':
drivers/ntb/test/ntb_perf.c:213:10: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
  vbase = (u64)(u64 *)mw->vbase;
          ^
drivers/ntb/test/ntb_perf.c:214:14: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
  dst_vaddr = (u64)(u64 *)dst;
              ^

This adds __iomem annotations where needed and changes the temporary
variables to iomem pointers to avoid casting them to u64. I did not
see the problem in linux-next earlier, but it show showed up in
4.5-rc1.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 8a7b6a778a ("ntb: ntb perf tool")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-03-17 20:38:40 -04:00
Allen Hubbe 03beaec80d NTB: Fix macro parameter conflict with field name
If the parameter given to the macro is replaced throughout the macro as
it is evaluated.  The intent is that the macro parameter should replace
the only the first parameter to container_of().  However, the way the
macro was written, it would also inadvertantly replace a structure field
name.  If a parameter of any other name is given to the macro, it will
fail to compile, if the structure does not contain a field of the same
name.  At worst, it will compile, and hide improper access of an
unintended field in the structure.

Change the macro parameter name, so it does not conflict with the
structure field name.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-01-21 19:53:10 -05:00
Xiangliang Yu a1b3695820 NTB: Add support for AMD PCI-Express Non-Transparent Bridge
This adds support for AMD's PCI-Express Non-Transparent Bridge
(NTB) device on the Zeppelin platform. The driver connnects to the
standard NTB sub-system interface, with modification to add hooks
for power management in a separate patch. The AMD NTB device has 3
memory windows, 16 doorbell, 16 scratch-pad registers, and supports
up to 16 PCIe lanes running a Gen3 speeds.

Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-01-21 19:51:04 -05:00
Dave Jiang 8a7b6a778a ntb: ntb perf tool
Providing raw performance data via a tool that directly access data from
NTB w/o any software overhead. This allows measurement of the hardware
performance limit. In revision one we are only doing single direction
CPU and DMA writes. Eventually we will provide bi-directional writes.

The measurement using DMA engine for NTB performance measure does
not measure the raw performance of DMA engine over NTB due to software
overhead. But it should provide the peak performance through the Linux DMA
driver.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-01-17 22:08:05 -05:00
Dave Jiang 8c874cc140 NTB: Address out of DMA descriptor issue with NTB
The transport right now does not handle the case where we run out of DMA
descriptors. We just fail when we do not succeed. Adding code to retry for
a bit attempting to use the DMA engine instead of instantly fail to CPU
copy.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-01-11 10:01:27 -05:00
Dave Jiang 703872c2c5 NTB: Clear property bits in BAR value
The lower bits read from a BAR register will contain property bits
that we do not care about. Clear those so that we can use the BAR
values for limit and xlat registers.

Reported-by: Conrad Meyer <cem@freebsd.org>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-01-11 09:51:17 -05:00
Jon Mason 179f912a39 NTB: ntb_process_tx error path bug
The transmit overrun avoidance error path in ntb_process_tx accidentally
swapped the first two values being passed to the tx_handler client.
This could result in crashes in the ntb_netdev (or other out-of-tree NTB
clients).

Reported-by: Alex Depoutovitch <alex@pernixdata.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2016-01-11 09:51:17 -05:00
Arnd Bergmann fdcb4b2e78 NTB: fix 32-bit compiler warning
resource_size_t may be 32-bit wide on some architectures, which causes
this warning when building the NTB code:

drivers/ntb/ntb_transport.c: In function 'ntb_transport_link_work':
drivers/ntb/ntb_transport.c:828:46: warning: right shift count >= width of type [-Wshift-count-overflow]

The warning is harmless but can be avoided by using the upper_32_bits()
macro.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-11-08 16:24:43 -05:00
Dave Jiang 8b782fab4d NTB: unify translation addresses
There is no need for the upstream and downstream addresses to be different
for the NTB configs. Go to using a single set of address. It is still
possible to configure them differently using module parameter override
however.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked and Tested-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-11-08 16:11:21 -05:00
Jon Mason c92ba3c5d9 NTB: invalid buf pointer in multi-MW setups
Order of operations issue with the QP Num and MW count, which would
result in the receive buffer pointer being invalid if there are more
than 1 MW.  Corrected with parenthesis to enforce the proper order of
operations.

Reported-by: John I. Kading <John.Kading@gd-ms.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-11-08 16:11:21 -05:00
Sudip Mukherjee 70d4687d60 NTB: remove unused variable
These variables were not used anywhere. So remove them.

Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-11-08 16:11:21 -05:00
Sudip Mukherjee d4adee09fd NTB: fix access of free-ed pointer
We were accessing nt->mw_vec after freeing it. Fix the error path so
that we free nt->mw_vec after we have finished using it.

Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-11-08 16:11:21 -05:00
Dave Jiang 04afde45e0 NTB: Fix issue where we may be accessing NULL ptr
smatch detected an issue in the function ntb_transport_max_size() where
we could be dereferencing a dma channel pointer when it is NULL.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-11-08 16:11:21 -05:00
Allen Hubbe 9a07826f99 NTB: Fix range check on memory window index
The range check must exclude the upper bound.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-09-07 15:27:12 -04:00
Allen Hubbe 2aa2a77a48 NTB: Improve index handling in B2B MW workaround
Check that b2b_mw_idx is in range of the number of memory windows when
initializing the device.  The workaround is considered to be in effect
only if the device b2b_idx is exactly UINT_MAX, instead of any index
past the last memory window.

Only print B2B MW workaround information in debugfs if the workaround is
in effect.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-09-07 15:27:12 -04:00
Dave Jiang 569410ca75 NTB: Use unique DMA channels for TX and RX
Allocate two DMA channels, one for TX operation and one for RX
operation, instead of having one DMA channel for everything. This
provides slightly better performance, and also will make error handling
cleaner later on.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-09-07 15:17:09 -04:00
Allen Hubbe 905921e748 NTB: Remove dma_sync_wait from ntb_async_rx
The dma_sync_wait can hurt the performance of workloads mixed with both
large and small frames.  Large frames will be copied using the dma
engine.  Small frames will be copied by the cpu.  The dma_sync_wait
prevents the cpu and dma engine copying in parallel.

In the period where the cpu is copying, the dma engine is stopped.  The
dma engine is not doing any useful work to copy large frames during that
time, and the additional time to restart the dma engine for the next
large frame.  This will decrease the throughput for the portion of a
workload with large frames.

In the period where the dma engine is copying, the cpu is held up
waiting for dma to complete.  The small frames processing will be
delayed until the dma is complete.  The RX frames are completed
in-order, and the processing of small frames takes very little time, so
dma_sync_wait may have an insignificant impact on the respose time of
frames.  The more significant impact is to the system, because the delay
in dma_sync_wait is implemented as busy non-blocking wait.  This can
prevent the delayed core from doing any useful work, even if it could be
processing work for other drivers, unrelated to transport RX processing.

After applying the earlier patch to fix out-of-order RX acknoledgement,
the dma_sync_wait is no longer necessary.  Remove it, so that cpu memcpy
will proceed immediately for small frames, in parallel with ongoing dma
for large frames.  Do not hold up the cpu from doing work while dma is
in progress.  The prior fix will continue to ensure in-order completion
of the RX frames to the upper layer, and in-order delivery of the RX
acknoledgement.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-09-07 15:17:08 -04:00
Dave Jiang d98ef99e37 NTB: Clean up QP stats info
Make QP stats info more readable for debugging purposes.  Also add an
entry to indicate whether DMA is being used.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-09-07 15:17:08 -04:00
Dave Jiang 315100004f NTB: Make the transport list in order of discovery
The list should be added from the bottom and not the top in order to
ensure the transport is provided in the same order to clients as ntb
devices are discovered.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-09-07 15:17:08 -04:00
Dave Jiang 0a5d19d9f0 NTB: Add PCI Device IDs for Broadwell Xeon
Adding PCI Device IDs for B2B (back to back), RP (root port, primary),
and TB (transparent bridge, secondary) devices.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-09-07 15:17:08 -04:00
Dave Jiang e74bfeedad NTB: Add flow control to the ntb_netdev
Right now if we push the NTB really hard, we start dropping packets due
to not able to process the packets fast enough. We need to st:qop the
upper layer from flooding us when that happens.

A timer is necessary in order to restart the queue once the resource has
been processed on the receive side. Due to the way NTB is setup, the
resources on the tx side are tied to the processing of the rx side and
there's no async way to know when the rx side has released those
resources.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-09-07 15:17:08 -04:00
Kees Cook e15f940908 ntb: avoid format string in dev_set_name
Avoid any chance of format string expansion when calling dev_set_name.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-08-09 16:32:22 -04:00
Allen Hubbe 30a4bb1e5a NTB: Fix dereference before check
Remove early dereference of a pointer that is checked later in the code.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-08-09 16:32:22 -04:00
Allen Hubbe 8c9edf63e7 NTB: Fix zero size or integer overflow in ntb_set_mw
A plain 32 bit integer will overflow for values over 4GiB.

Change the plain integer size to the appropriate size type in
ntb_set_mw.  Change the type of the size parameter and two local
variables used for size.

Even if there is no overflow, a size of zero is invalid here.

Reported-by: Juyoung Jung <jjung@micron.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-08-09 16:32:22 -04:00
Allen Hubbe 8b5a22d8f1 NTB: Schedule to receive on QP link up
Schedule to receive on QP link up, to make sure that the doorbell is
properly cleared for interrupts.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-08-09 16:32:22 -04:00
Dave Jiang 260bee9451 NTB: Fix oops in debugfs when transport is half-up
When the remote side is not up, we do not have all the context for the
transport, and that causes NULL ptr access. Have the debugfs reads check
to see if transport is up before we make access.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-08-09 16:32:22 -04:00
Dave Jiang c8650fd03d NTB: Fix transport stats for multiple devices
Currently the debugfs does not have files for all NTB transport queue
pairs.  When there are multiple NTBs present in a system, the QP names
of the last transport clobber the names of previously added transport
QPs.  Only the last added QPs can be observed via debugfs.

Create a directory per NTB transport to associate the QPs with that
transport.  Name the directory the same as the PCI device.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-08-09 16:32:21 -04:00
Allen Hubbe da2e5ae561 NTB: Fix ntb_transport out-of-order RX update
It was possible for a synchronous update of the RX index in the error
case to get ahead of the asynchronous RX index update in the normal
case.  Change the RX processing to preserve an RX completion order.

There were two error cases.  First, if a buffer is not present to
receive data, there would be no queue entry to preserve the RX
completion order.  Instead of dropping the RX frame, leave the RX frame
in the ring.  Schedule RX processing when RX entries are enqueued, in
case there are RX frames waiting in the ring to be received.

Second, if a buffer is too small to receive data, drop the frame in the
ring, mark the RX entry as done, and indicate the error in the RX entry
length.  Check for a negative length in the receive callback in
ntb_netdev, and count occurrences as rx_length_errors.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-08-09 16:32:21 -04:00
Dave Jiang bf44fe4671 NTB: Add split BAR output for debugfs stats
When split BAR is enabled, the driver needs to dump out the split BAR
registers rather than the original 64bit BAR registers.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:09:32 -04:00
Dave Jiang fd839bf884 NTB: Change WARN_ON_ONCE to pr_warn_once on unsafe
The unsafe doorbell and scratchpad access should display reason when
WARN is called.  Otherwise we get a stack dump without any explanation.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:09:30 -04:00
Dave Jiang 7eb387813d NTB: Print driver name and version in module init
Printouts driver name and version to indicate what is being loaded.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:09:28 -04:00
Dave Jiang 9891417de8 NTB: Increase transport MTU to 64k from 16k
Benchmarking showed a significant performance increase with the MTU size
to 64k instead of 16k.  Change the driver default to 64k.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:09:27 -04:00
Dave Jiang 2f887b9a44 NTB: Rename Intel code names to platform names
Instead of using the platform code names, use the correct platform names
to identify the respective Intel NTB hardware.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:09:25 -04:00
Dave Jiang a41ef053f7 NTB: Default to CPU memcpy for performance
Disable DMA usage by default, since the CPU provides much better
performance with write combining.  Provide a module parameter to enable
DMA usage when offloading the memcpy is preferred.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:09:24 -04:00
Dave Jiang 06917f7535 NTB: Improve performance with write combining
Changing the memory window BAR mappings to write combining significantly
boosts the performance.  We will also use memcpy that uses non-temporal
store, which showed performance improvement when doing non-cached
memcpys.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:09:21 -04:00
Allen Hubbe 0e041fb536 NTB: Use NUMA memory in Intel driver
Allocate memory for the NUMA node of the NTB device.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:09:19 -04:00
Allen Hubbe 1199aa6126 NTB: Use NUMA memory and DMA chan in transport
Allocate memory and request the DMA channel for the same NUMA node as
the NTB device.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:08:33 -04:00
Allen Hubbe 2876228941 NTB: Rate limit ntb_qp_link_work
When the ntb transport is connecting and waiting for the peer, the debug
console receives lots of debug level messages about the remote qp link
status being down.  Rate limit those messages.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:08:30 -04:00
Allen Hubbe 578b881ba9 NTB: Add tool test client
This is a simple debugging driver that enables the doorbell and
scratch pad registers to be read and written from the debugfs.  This
tool enables more complicated debugging to be scripted from user space.
This driver may be used to test that your ntb hardware and drivers are
functioning at a basic level.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:08:17 -04:00
Allen Hubbe 963de4739f NTB: Add ping pong test client
This is a simple ping pong driver that exercises the scratch pads and
doorbells of the ntb hardware.  This driver may be used to test that
your ntb hardware and drivers are functioning at a basic level.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:07:42 -04:00
Allen Hubbe 42fefc86a6 NTB: Add parameters for Intel SNB B2B addresses
Add module parameters for the addresses to be used in B2B topology.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:06:40 -04:00
Allen Hubbe 2849b5d706 NTB: Reset transport QP link stats on down
Reset the link stats when the link goes down.  In particular, the TX and
RX index and count must be reset, or else the TX side will be sending
packets to the RX side where the RX side is not expecting them.  Reset
all the stats, to be consistent.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:06:34 -04:00
Allen Hubbe c0900b33d1 NTB: Do not advance transport RX on link down
On link down, don't advance RX index to the next entry.  The next entry
should never be valid after receiving the link down flag.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:06:24 -04:00
Allen Hubbe e22e0b9dcf NTB: Differentiate transport link down messages
The same message "qp %d: Link Down\n" was printed at two locations in
ntb_transport.  Change the messages so they are distinct.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:06:19 -04:00
Dave Jiang dd5d4d8edb NTB: Check the device ID to set errata flags
Set errata flags for the specific device IDs to which they apply,
instead of the whole Xeon hardware class.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:06:14 -04:00
Dave Jiang 5ae0beb6bc NTB: Enable link for Intel root port mode in probe
Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen.  Otherwise the ntb device will not show up on the transparent
bridge side of the link.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:06:08 -04:00
Dave Jiang 0f69a7dff9 NTB: Read peer info from local SPAD in transport
The transport was writing and then reading the peer scratch pad,
essentially reading what it just wrote instead of exchanging any
information with the peer.  The transport expects the peer values to be
the same as the local values, so this issue was not obvious.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:06:00 -04:00
Allen Hubbe e26a5843f7 NTB: Split ntb_hw_intel and ntb_transport drivers
Change ntb_hw_intel to use the new NTB hardware abstraction layer.

Split ntb_transport into its own driver.  Change it to use the new NTB
hardware abstraction layer.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:05:49 -04:00
Allen Hubbe a1bd3baeb2 NTB: Add NTB hardware abstraction layer
Abstract the NTB device behind a programming interface, so that it can
support different hardware and client drivers.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-04 14:04:44 -04:00
Allen Hubbe ec110bc7cc NTB: Move files in preparation for NTB abstraction
This patch only moves files to their new locations, before applying the
next two patches adding the NTB Abstraction layer.  Splitting this patch
from the next is intended make distinct which code is changed only due
to moving the files, versus which are substantial code changes in adding
the NTB Abstraction layer.

Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-07-02 10:09:23 -04:00
Linus Torvalds d8133356e9 PCI changes for the v4.2 merge window:
Enumeration
     - Move pci_ari_enabled() to global header (Alex Williamson)
     - Account for ARI in _PRT lookups (Alex Williamson)
     - Remove unused pci_scan_bus_parented() (Yijing Wang)
 
   Resource management
     - Use host bridge _CRS info on systems with >32 bit addressing (Bjorn Helgaas)
     - Use host bridge _CRS info on Foxconn K8M890-8237A (Bjorn Helgaas)
     - Fix pci_address_to_pio() conversion of CPU address to I/O port (Zhichang Yuan)
     - Add pci_bus_addr_t (Yinghai Lu)
 
   PCI device hotplug
     - Wait for pciehp command completion where necessary (Alex Williamson)
     - Drop pointless ACPI-based "slot detection" check (Rafael J. Wysocki)
     - Check ignore_hotplug for all downstream devices (Rafael J. Wysocki)
     - Propagate the "ignore hotplug" setting to parent (Rafael J. Wysocki)
     - Inline pciehp "handle event" functions into the ISR (Bjorn Helgaas)
     - Clean up pciehp debug logging (Bjorn Helgaas)
 
   Power management
     - Remove redundant PCIe port type checking (Yijing Wang)
     - Add dev->has_secondary_link to track downstream PCIe links (Yijing Wang)
     - Use dev->has_secondary_link to find downstream links for ASPM (Yijing Wang)
     - Drop __pci_disable_link_state() useless "force" parameter (Bjorn Helgaas)
     - Simplify Clock Power Management setting (Bjorn Helgaas)
 
   Virtualization
     - Add ACS quirks for Intel 9-series PCH root ports (Alex Williamson)
     - Add function 1 DMA alias quirk for Marvell 9120 (Sakari Ailus)
 
   MSI
     - Disable MSI at enumeration even if kernel doesn't support MSI (Michael S. Tsirkin)
     - Remove unused pci_msi_off() (Bjorn Helgaas)
     - Rename msi_set_enable(), msix_clear_and_set_ctrl() (Michael S.  Tsirkin)
     - Export pci_msi_set_enable(), pci_msix_clear_and_set_ctrl() (Michael S. Tsirkin)
     - Drop pci_msi_off() calls during probe (Michael S. Tsirkin)
 
   APM X-Gene host bridge driver
     - Add APM X-Gene v1 PCIe MSI/MSIX termination driver (Duc Dang)
     - Add APM X-Gene PCIe MSI DTS nodes (Duc Dang)
     - Disable Configuration Request Retry Status for v1 silicon (Duc Dang)
     - Allow config access to Root Port even when link is down (Duc Dang)
 
   Broadcom iProc host bridge driver
     - Allow override of device tree IRQ mapping function (Hauke Mehrtens)
     - Add BCMA PCIe driver (Hauke Mehrtens)
     - Directly add PCI resources (Hauke Mehrtens)
     - Free resource list after registration (Hauke Mehrtens)
 
   Freescale i.MX6 host bridge driver
     - Add speed change timeout message (Troy Kisky)
     - Rename imx6_pcie_start_link() to imx6_pcie_establish_link() (Bjorn Helgaas)
 
   Freescale Layerscape host bridge driver
     - Use dw_pcie_link_up() consistently (Bjorn Helgaas)
     - Factor out ls_pcie_establish_link() (Bjorn Helgaas)
 
   Marvell MVEBU host bridge driver
     - Remove mvebu_pcie_scan_bus() (Yijing Wang)
 
   NVIDIA Tegra host bridge driver
     - Remove tegra_pcie_scan_bus() (Yijing Wang)
 
   Synopsys DesignWare host bridge driver
     - Consolidate outbound iATU programming functions (Jisheng Zhang)
     - Use iATU0 for cfg and IO, iATU1 for MEM (Jisheng Zhang)
     - Add support for x8 links (Zhou Wang)
     - Wait for link to come up with consistent style (Bjorn Helgaas)
     - Use pci_scan_root_bus() for simplicity (Yijing Wang)
 
   TI DRA7xx host bridge driver
     - Use dw_pcie_link_up() consistently (Bjorn Helgaas)
 
   Miscellaneous
     - Include <linux/pci.h>, not <asm/pci.h> (Bjorn Helgaas)
     - Remove unnecessary #includes of <asm/pci.h> (Bjorn Helgaas)
     - Remove unused pcibios_select_root() (again) (Bjorn Helgaas)
     - Remove unused pci_dma_burst_advice() (Bjorn Helgaas)
     - xen/pcifront: Don't use deprecated function pci_scan_bus_parented() (Arnd Bergmann)
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJViCSWAAoJEFmIoMA60/r8zX8P/1DPNnk+8xSQe3dYjnG8VW3P
 GPxeCqLMkjiF3ffxcLDzsgrHMjZEb8Co67WePs0k5V0lbZevoIwUo48+oO9B5jhc
 H5DuPZHyTHeOvaZv4GUY5vq/1DBh4JXmJc2V/BkaJ6qhXckF+SCam9C+s0p4950o
 QX/ifOjg/VHzmhaiL7wymJOzuniZmIttl+y+nzkl3AUJ+T6ZtQbUhz+8GZ3lj7Ma
 F+7JHhvm9K8Ljajxb6BLWTw4xgHA6ZN5PtYEx+Sl9QBYSsGfL7LnqyYD3KhJ7KV5
 4AHNJGEVhzNwSuyh+VQx1tNm7OHOqkAaTsYdCVUZRow+6CPd8P75QOMtpl+SmPJB
 RV1BAO75OTGqKg0B9IDg855y4Nh+4/dKoZlBPzpp7+cKw3ylaRAsNnaZ9ik5D62v
 RR06CFgWGHwDXSObgbRm4v0HwfAIHWWJzrPqAZmElh2dzb1Lv1I3AbB1SClCN6sl
 fnAu6CAwA47A5GT8xW3L0oQXdcSmdNUdNzZrsfDnOBIQWMsF+zBFKr6sTABVgyxp
 /WEJaNlvx8Zlq0bZlhGDdsGSbFNFzhX4avWZtXhvdcqFzH0KaVghYSayYvJE9Haq
 oakWqS+GZ3x40j+rdrgLg98AWRVraE1MvV1A7N9TIGjuuKqqbZfSP8kvX3QRQQhO
 Z2+X5hMM0s/tdYtADYu/
 =Qw+j
 -----END PGP SIGNATURE-----

Merge tag 'pci-v4.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull PCI updates from Bjorn Helgaas:
 "PCI changes for the v4.2 merge window:

  Enumeration
    - Move pci_ari_enabled() to global header (Alex Williamson)
    - Account for ARI in _PRT lookups (Alex Williamson)
    - Remove unused pci_scan_bus_parented() (Yijing Wang)

  Resource management
    - Use host bridge _CRS info on systems with >32 bit addressing (Bjorn Helgaas)
    - Use host bridge _CRS info on Foxconn K8M890-8237A (Bjorn Helgaas)
    - Fix pci_address_to_pio() conversion of CPU address to I/O port (Zhichang Yuan)
    - Add pci_bus_addr_t (Yinghai Lu)

  PCI device hotplug
    - Wait for pciehp command completion where necessary (Alex Williamson)
    - Drop pointless ACPI-based "slot detection" check (Rafael J. Wysocki)
    - Check ignore_hotplug for all downstream devices (Rafael J. Wysocki)
    - Propagate the "ignore hotplug" setting to parent (Rafael J. Wysocki)
    - Inline pciehp "handle event" functions into the ISR (Bjorn Helgaas)
    - Clean up pciehp debug logging (Bjorn Helgaas)

  Power management
    - Remove redundant PCIe port type checking (Yijing Wang)
    - Add dev->has_secondary_link to track downstream PCIe links (Yijing Wang)
    - Use dev->has_secondary_link to find downstream links for ASPM (Yijing Wang)
    - Drop __pci_disable_link_state() useless "force" parameter (Bjorn Helgaas)
    - Simplify Clock Power Management setting (Bjorn Helgaas)

  Virtualization
    - Add ACS quirks for Intel 9-series PCH root ports (Alex Williamson)
    - Add function 1 DMA alias quirk for Marvell 9120 (Sakari Ailus)

  MSI
    - Disable MSI at enumeration even if kernel doesn't support MSI (Michael S. Tsirkin)
    - Remove unused pci_msi_off() (Bjorn Helgaas)
    - Rename msi_set_enable(), msix_clear_and_set_ctrl() (Michael S.  Tsirkin)
    - Export pci_msi_set_enable(), pci_msix_clear_and_set_ctrl() (Michael S. Tsirkin)
    - Drop pci_msi_off() calls during probe (Michael S. Tsirkin)

  APM X-Gene host bridge driver
    - Add APM X-Gene v1 PCIe MSI/MSIX termination driver (Duc Dang)
    - Add APM X-Gene PCIe MSI DTS nodes (Duc Dang)
    - Disable Configuration Request Retry Status for v1 silicon (Duc Dang)
    - Allow config access to Root Port even when link is down (Duc Dang)

  Broadcom iProc host bridge driver
    - Allow override of device tree IRQ mapping function (Hauke Mehrtens)
    - Add BCMA PCIe driver (Hauke Mehrtens)
    - Directly add PCI resources (Hauke Mehrtens)
    - Free resource list after registration (Hauke Mehrtens)

  Freescale i.MX6 host bridge driver
    - Add speed change timeout message (Troy Kisky)
    - Rename imx6_pcie_start_link() to imx6_pcie_establish_link() (Bjorn Helgaas)

  Freescale Layerscape host bridge driver
    - Use dw_pcie_link_up() consistently (Bjorn Helgaas)
    - Factor out ls_pcie_establish_link() (Bjorn Helgaas)

  Marvell MVEBU host bridge driver
    - Remove mvebu_pcie_scan_bus() (Yijing Wang)

  NVIDIA Tegra host bridge driver
    - Remove tegra_pcie_scan_bus() (Yijing Wang)

  Synopsys DesignWare host bridge driver
    - Consolidate outbound iATU programming functions (Jisheng Zhang)
    - Use iATU0 for cfg and IO, iATU1 for MEM (Jisheng Zhang)
    - Add support for x8 links (Zhou Wang)
    - Wait for link to come up with consistent style (Bjorn Helgaas)
    - Use pci_scan_root_bus() for simplicity (Yijing Wang)

  TI DRA7xx host bridge driver
    - Use dw_pcie_link_up() consistently (Bjorn Helgaas)

  Miscellaneous
    - Include <linux/pci.h>, not <asm/pci.h> (Bjorn Helgaas)
    - Remove unnecessary #includes of <asm/pci.h> (Bjorn Helgaas)
    - Remove unused pcibios_select_root() (again) (Bjorn Helgaas)
    - Remove unused pci_dma_burst_advice() (Bjorn Helgaas)
    - xen/pcifront: Don't use deprecated function pci_scan_bus_parented() (Arnd Bergmann)"

* tag 'pci-v4.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (58 commits)
  PCI: pciehp: Inline the "handle event" functions into the ISR
  PCI: pciehp: Rename queue_interrupt_event() to pciehp_queue_interrupt_event()
  PCI: pciehp: Make queue_interrupt_event() void
  PCI: xgene: Allow config access to Root Port even when link is down
  PCI: xgene: Disable Configuration Request Retry Status for v1 silicon
  PCI: pciehp: Clean up debug logging
  x86/PCI: Use host bridge _CRS info on systems with >32 bit addressing
  PCI: imx6: Add #define PCIE_RC_LCSR
  PCI: imx6: Use "u32", not "uint32_t"
  PCI: Remove unused pci_scan_bus_parented()
  xen/pcifront: Don't use deprecated function pci_scan_bus_parented()
  PCI: imx6: Add speed change timeout message
  PCI/ASPM: Simplify Clock Power Management setting
  PCI: designware: Wait for link to come up with consistent style
  PCI: layerscape: Factor out ls_pcie_establish_link()
  PCI: layerscape: Use dw_pcie_link_up() consistently
  PCI: dra7xx: Use dw_pcie_link_up() consistently
  x86/PCI: Use host bridge _CRS info on Foxconn K8M890-8237A
  PCI: pciehp: Wait for hotplug command completion where necessary
  PCI: Remove unused pci_dma_burst_advice()
  ...
2015-06-23 13:41:24 -07:00
Daniel Verkamp ebaad1322d ntb: initialize max_mw for Atom before using it
Commit ab760a0 (ntb: Adding split BAR support for Haswell platforms)
changed ntb_device's mw from a fixed-size array into a pointer that is
allocated based on limits.max_mw; however, on Atom platforms, max_mw
is not initialized until ntb_device_setup(), which happens after the
allocation.

Fill out max_mw in ntb_atom_detect() to match ntb_xeon_detect(); this
happens before the use of max_mw in the ndev->mw allocation.

Fixes a null pointer dereference on Atom platforms with ntb hardware.

v2: fix typo (mw_max should be max_mw)

Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-06-11 09:27:24 -04:00
Jon Mason 2f4eb6a80e ntb: iounmap MW reg and vbase in error path
The MW regbase and vbase(s) were not being freed if an error occurred
in the vbase allocation loop.  This is corrected by updating the error
path for the allocation loop to err4.

Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2015-06-08 22:38:40 -04:00
Michael S. Tsirkin 8c9bb608e8 ntb: Drop pci_msi_off() call during probe
The PCI core now disables MSI and MSI-X for all devices during enumeration
regardless of CONFIG_PCI_MSI.  Remove device-specific code to disable
MSI/MSI-X.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2015-05-07 09:52:22 -05:00
Dave Jiang ab760a0c56 ntb: Adding split BAR support for Haswell platforms
On the Haswell platform, a split BAR option to allow creation of 2
32bit BARs (4 and 5) from the 64bit BAR 4. Adding support for this
new option.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2014-10-17 07:08:51 -04:00
Dave Jiang 069684e888 ntb: use errata flag set via DID to implement workaround
Instead of using a module parameter, we should detect the errata via
PCI DID and then set an appropriate flag. This will be used for additional
errata later on.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2014-10-17 07:08:51 -04:00
Dave Jiang 1db97f2589 ntb: conslidate reading of PPD to move platform detection earlier
To simplify some of the platform detection code. Move the platform detection
to a function to be called earlier.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2014-10-17 07:08:50 -04:00
Dave Jiang b775e85bdb ntb: move platform detection to separate function
Move the platform detection function to separate functions to allow
easier maintenence.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2014-10-17 07:08:50 -04:00
Jon Mason 6465d02ee1 NTB: debugfs device entry
Create a debugfs entry for the NTB device to log the basic device info,
as well as display the error count on a number of registers.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2014-10-17 07:08:50 -04:00
Dave Jiang 3cc5ba1938 ntb: Add alignment check to meet hardware requirement
The NTB translate register must have the value to be BAR size aligned.
This alignment check make sure that the DMA memory allocated has the
proper alignment. Another requirement for NTB to function properly with
memory window BAR size greater or equal to 4M is to use the CMA feature
in 3.16 kernel with the appropriate CONFIG_CMA_ALIGNMENT and
CONFIG_CMA_SIZE_MBYTES set.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
2014-09-14 00:10:38 -04:00
Jon Mason a1413cfbcb NTB: correct the spread of queues over mw's
The detection of an uneven number of queues on the given memory windows
was not correct.  The mw_num is zero based and the mod should be
division to spread them evenly over the mw's.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2014-09-14 00:10:38 -04:00
Alexander Gordeev f220baad08 ntb: Use pci_enable_msix_range() instead of pci_enable_msix()
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.

Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
2014-04-07 10:59:20 -07:00
Alexander Gordeev 53a788a765 ntb: Split ntb_setup_msix() into separate BWD/SNB routines
This is an cleanup effort to make ntb_setup_msix() more
readable - use ntb_setup_bwd_msix() to init MSI-Xs on
BWD hardware and ntb_setup_snb_msix() - on SNB hardware.

Function ntb_setup_snb_msix() also initializes MSI-Xs the
way it should has been done - looping pci_enable_msix()
until success or failure.

Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
2014-04-07 10:59:19 -07:00
Alexander Gordeev 77733513c4 ntb: Use pci_msix_vec_count() to obtain number of MSI-Xs
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
2014-04-07 10:59:19 -07:00
Jon Mason 53ca4fea0b NTB: Code Style Clean-up
Some white space and 80 char overruns corrected.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2014-04-07 10:59:19 -07:00
Jon Mason 403c63cb6d NTB: client event cleanup
Provide a better event interface between the client and transport

Signed-off-by: Jon Mason <jon.mason@intel.com>
2014-04-07 10:59:19 -07:00
Alexander Gordeev 717e8e8bfe ntb: Fix leakage of ntb_device::msix_entries[] array
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
2014-04-07 10:58:14 -07:00
Roland Dreier c8eee3795d NTB: Fix typo in setting one translation register
In the code for Xeon devices in back-to-back mode with xeon_errata_workaround
disabled, the downstream device puts the wrong value in SNB_B2B_XLAT_OFFSETL
(SNB_MBAR01_DSD_ADDR vs. SNB_MBAR01_USD_ADDR).

This was spotted while reading code, since the typo has no practical effect,
at least for now: the low 32 bits of both constants are actually identical
anyway.  However, it's clearer and safer to use the right name.

Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
2014-04-07 10:58:14 -07:00
Linus Torvalds b95485143b NTB driver bug fixes to address a missed call to pci_enable_msix,
NTB-RP Link Up issue, Xeon Doorbell errata workaround, ntb_transport
 link down race, and correct dmaengine_get/put usage.  Also, clean-ups
 to remove duplicate defines and document a hardware errata.  Finally,
 some changes to improve performance.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJSj/dCAAoJEG5mS6x6i9IjCfAP/0pVA7VYAjQQGLtpUIf8RNIe
 iNV58Q3h74+CSzyHkz51HYuJB+6uRC6c0ChKuZMUZk/ca3hqfW0FcC1V3SjYLzxP
 Bdf687TaEE4WJOaTI5hnAzzDQ+gU9aE4DgaqvFz43M4jh4scSleuE+CQ0Pjm682x
 71KespuPO7Z77EC5QPbWWV5KRSkF4FHuAuDcr8TYAmSnCb8VDGDxdnwYYwBTeY3j
 DuPUwLGwvbE6X4gWmOYZSwDz6cArEs1CunpeP3EUFY4rjTZArc4MSLWdC6lYQtZp
 T90khUDU/UklUqlOOuydJe30zT60uPBagcEL94JxyWFT+wa5b/ra+gvU+FE4NBzA
 ZW6LVlXnYTQ5XJeO5HNDRBHPZ3zZaDI+TGDBM13EBS0wbcO3PojR6Z78nlkjPLeJ
 /a1sIEfM3ts7u3Vpw8GpBbhl6+8tP6xbV/rDbzfE6mfq/VVwbfAa/k9oQVh8pfoJ
 YyGq1Gr43aAFm0imPRF0qRNDnSDF2UiYrNHntWWyfhW7Vmq/EjT0H21AHhgxnP7b
 3AaKQl7nuYoNzx6x8ZiEcSkDy+8qY84i2vUzd9Qll/SBVCOK7KvBoFmu9x7D+ZdN
 0mS4qFNXSmHhow7ur2ffwzIaSkggVIhLbEiH4bYbPP+wXzhlTLTnnRb3lFmTs/5X
 /HTR7QGxfDAzcjpYAzlS
 =nOG2
 -----END PGP SIGNATURE-----

Merge tag 'ntb-3.13' of git://github.com/jonmason/ntb

Pull non-transparent bridge updates from Jon Mason:
 "NTB driver bug fixes to address a missed call to pci_enable_msix,
  NTB-RP Link Up issue, Xeon Doorbell errata workaround, ntb_transport
  link down race, and correct dmaengine_get/put usage.

  Also, clean-ups to remove duplicate defines and document a hardware
  errata.  Finally, some changes to improve performance"

* tag 'ntb-3.13' of git://github.com/jonmason/ntb:
  NTB: Disable interrupts and poll under high load
  NTB: Enable Snoop on Primary Side
  NTB: Document HW errata
  NTB: remove duplicate defines
  NTB: correct dmaengine_get/put usage
  NTB: Fix ntb_transport link down race
  ntb: Fix missed call to pci_enable_msix()
  NTB: Fix NTB-RP Link Up
  NTB: Xeon Doorbell errata workaround
2013-11-26 11:15:12 -08:00
Jon Mason e8aeb60c38 NTB: Disable interrupts and poll under high load
Disable interrupts and poll under high load

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-11-20 09:57:34 -07:00
Jon Mason 78958433db NTB: Enable Snoop on Primary Side
Enable Snoop from Primary to Secondary side on BAR23 and BAR45 on all
TLPs.  Previously, Snoop was only enabled from Secondary to Primary
side.  This can have a performance improvement on some workloads.

Also, make the code more obvious about how the link is being enabled.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-11-20 09:57:33 -07:00
Jon Mason 58b889206e NTB: Document HW errata
Add a comment describing the necessary ordering of modifications to the
NTB Limit and Base registers.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-11-20 09:57:33 -07:00
Michael Opdenacker dcf81964e1 NTB: remove duplicate defines
Remove duplicate defines in drivers/ntb/ntb_regs.h

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-11-20 09:57:33 -07:00
Jon Mason 94681194e6 NTB: correct dmaengine_get/put usage
dmaengine_get() causes the initialization of the per-cpu channel tables.
It needs to be called prior to dma_find_channel().

Initial version by Dan Williams <dan.j.williams@intel.com>

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-11-20 09:57:32 -07:00
Jon Mason fca4d5188c NTB: Fix ntb_transport link down race
A WARN_ON is being hit in ntb_qp_link_work due to the NTB transport link
being down while the ntb qp link is still active.  This is caused by the
transport link being brought down prior to the qp link worker thread
being terminated.  To correct this, shutdown the qp's prior to bringing
the transport link down.  Also, only call the qp worker thread if it is
in interrupt context, otherwise call the function directly.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-11-20 09:57:32 -07:00
Alexander Gordeev 9739047380 ntb: Fix missed call to pci_enable_msix()
Current MSI-X enablement code assumes MSI-Xs were successfully
allocated in case less than requested vectors were available.
That assumption is wrong, since MSI-Xs should be enabled with
a repeated call to pci_enable_msix(). This update fixes this.

Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-11-20 09:57:31 -07:00
Jon Mason 9fec60c414 NTB: Fix NTB-RP Link Up
The Xeon NTB-RP setup, the transparent side does not get a link up/down
interrupt.  Since the presence of a NTB device on the transparent side
means that we have a NTB link up, we can work around the lack of an
interrupt by simply calling the link up function to notify the upper
layers.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-11-20 09:57:31 -07:00
Jon Mason c529aa3033 NTB: Xeon Doorbell errata workaround
Modifications to the 14th bit of the B2BDOORBELL register will not be
mirrored to the remote system due to a hardware issue.  To get around
the issue, shrink the number of available doorbell bits by 1.  The max
number of doorbells was being used as a way to referencing the Link
Doorbell bit.  Since this would no longer work, the driver must now
explicitly reference that bit.

This does not affect the xeon_errata_workaround case, as it is not using
the b2bdoorbell register.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-11-20 09:57:30 -07:00
Bartlomiej Zolnierkiewicz 0776ae7b89 dmaengine: remove DMA unmap flags
Remove no longer needed DMA unmap flags:
- DMA_COMPL_SKIP_SRC_UNMAP
- DMA_COMPL_SKIP_DEST_UNMAP
- DMA_COMPL_SRC_UNMAP_SINGLE
- DMA_COMPL_DEST_UNMAP_SINGLE

Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jon Mason <jon.mason@intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
[djbw: clean up straggling skip unmap flags in ntb]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2013-11-14 11:04:38 -08:00
Bartlomiej Zolnierkiewicz 6f57fd0578 NTB: convert to dmaengine_unmap_data
Use the generic unmap object to unmap dma buffers.

Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jon Mason <jon.mason@intel.com>
[djbw: fix up unmap len, and GFP flags]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2013-11-14 11:01:32 -08:00
Yijing Wang 73f47cadfe ntb: clean up unnecessary MSI/MSI-X capability find
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.

Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-05 11:08:01 -07:00
Jon Mason db3bb3f07e NTB: Update Version
Update NTB version to 1.0

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-05 11:08:00 -07:00
Jon Mason f9a2cf890b NTB: Comment Fix
Add "data" ntb_register_db_callback parameter description comment and
correct poor spelling.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-05 11:08:00 -07:00
Jon Mason 3daa3a073e NTB: Remove unused variable
Remove unused pci_dev variable from ntb_transport_free()

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-05 11:07:59 -07:00
Jon Mason b1ef004303 NTB: Remove References of non-B2B BWD HW
NTB-RP is not a supported configuration on BWD hardware.  Remove the
code attempting to set it up.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-05 11:07:59 -07:00
Jon Mason ed6c24eda9 NTB: NTB-RP support
Add support for Non-Transparent Bridge connected to a PCI-E Root Port on
the remote system (also known as NTB-RP mode).  This allows for a NTB
enabled system to be connected to a non-NTB enabled system/slot.

Modifications to the registers and BARs/MWs on the Secondary side by the
remote system are reflected into registers on the Primary side for the
local system.  Similarly, modifications of registers and BARs/MWs on
Primary side by the local system are reflected into registers on the
Secondary side for the Remote System.  This allows communication between
the 2 sides via these registers and BARs/MWs.

Note: there is not a fix for the Xeon Errata (that was already worked
around in NTB-B2B mode) for NTB-RP mode.  Due to this limitation, NTB-RP
will not work on the Secondary side with the Xeon Errata workaround
enabled.  To get around this, disable the workaround via the
xeon_errata_workaround=0 modparm.  However, this can cause the hang
described in the errata.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-05 11:07:58 -07:00
Jon Mason 497938890a NTB: Rename Variables for NTB-RP
Many variable names in the NTB driver refer to the primary or secondary
side.  However, these variables will be used to access the reverse case
when in NTB-RP mode.  Make these names more generic in anticipation of
NTB-RP support.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-05 11:07:58 -07:00
Jon Mason 282a2feeb9 NTB: Use DMA Engine to Transmit and Receive
Allocate and use a DMA engine channel to transmit and receive data over
NTB.  If none is allocated, fall back to using the CPU to transfer data.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
2013-09-05 11:04:09 -07:00
Jon Mason ac477afb04 NTB: Enable 32bit Support
Correct the issues on NTB that prevented it from working on x86_32 and
modify the Kconfig to allow it to be permitted to be used in that
environment as well.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-03 14:48:53 -07:00
Jon Mason be4dac0fca NTB: Update Device IDs
Add support for new Intel NTB devices on upcoming Xeon hardware.  Since
the Xeon hardware design is already in place in the driver, all that is
needed are the new device ids.

Remove the device IDs for NTB devs running in Transparent Bridge mode,
as this driver is not being used for those devices.

Rename the device IDs for NTB devs running in NTB-RP mode to better
identify their usage model.  "PS" to denote the Primary Side of NTB, and
"SS" to denote the secondary side.  The primary side is the interface
exposed to the local system, and the secondary side is the interface
exposed to the remote system.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-03 14:48:53 -07:00
Jon Mason 113bf1c9f1 NTB: BWD Link Recovery
The BWD NTB device will drop the link if an error is encountered on the
point-to-point PCI bridge.  The link will stay down until all errors are
cleared and the link is re-established.  On link down, check to see if
the error is detected, if so do the necessary housekeeping to try and
recover from the error and reestablish the link.

There is a potential race between the 2 NTB devices recovering at the
same time.  If the times are synchronized, the link will not recover and the
driver will be stuck in this loop forever.  Add a random interval to the
recovery time to prevent this race.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-03 14:48:52 -07:00
Jon Mason 948d3a65b6 NTB: Xeon Errata Workaround
There is a Xeon hardware errata related to writes to SDOORBELL or
B2BDOORBELL in conjunction with inbound access to NTB MMIO Space, which
may hang the system.  To workaround this issue, use one of the memory
windows to access the interrupt and scratch pad registers on the remote
system.  This bypasses the issue, but removes one of the memory windows
from use by the transport.  This reduction of MWs necessitates adding
some logic to determine the number of available MWs.

Since some NTB usage methodologies may have unidirectional traffic, the
ability to disable the workaround via modparm has been added.

See BF113 in
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-c5500-c3500-spec-update.pdf
See BT119 in
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-e5-family-spec-update.pdf

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-03 13:51:51 -07:00
Jon Mason 1517a3f21a NTB: Correct debugfs to work with more than 1 NTB Device
Debugfs was setup in NTB to only have a single debugfs directory.  This
resulted in the leaking of debugfs directories and files when multiple
NTB devices were present, due to each device stomping on the variables
containing the previous device's values (thus preventing them from being
freed on cleanup).  Correct this by creating a secondary directory of
the PCI BDF for each device present, and nesting the previously existing
information in those directories.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-03 11:14:54 -07:00
Jon Mason b6750cfe07 NTB: Correct USD/DSD Identification
Due to ambiguous documentation, the USD/DSD identification is backward
when compared to the setting in BIOS.  Correct the bits to match the
BIOS setting.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-03 11:13:14 -07:00
Jon Mason 8703451151 NTB: Correct Number of Scratch Pad Registers
The NTB Xeon hardware has 16 scratch pad registers and 16 back-to-back
scratch pad registers.  Correct the #define to represent this and update
the variable names to reflect their usage.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-03 11:13:13 -07:00
Jon Mason 3b12a0d15b NTB: Add Error Handling in ntb_device_setup
If an error is encountered in ntb_device_setup, it is possible that the
spci_cmd isn't populated.  Writes to the offset can result in a NULL
pointer dereference.  This issue is easily encountered by running in
NTB-RP mode, as it currently is not supported and will generate an
error.  To get around this issue, return if an error is encountered
prior to attempting to write to the spci_cmd offset.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-09-03 11:13:12 -07:00
Jon Mason 8b19d450ad
NTB: Multiple NTB client fix
Fix issue with adding multiple ntb client devices to the ntb virtual
bus.  Previously, multiple devices would be added with the same name,
resulting in crashes.  To get around this issue, add a unique number to
the device when it is added.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-05-15 10:58:22 -07:00
Jon Mason c336acd333
NTB: memcpy lockup workaround
The system will appear to lockup for long periods of time due to the NTB
driver spending too much time in memcpy.  Avoid this by reducing the
number of packets that can be serviced on a given interrupt.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-05-15 10:58:06 -07:00
Jon Mason c9d534c8cb
NTB: Correctly handle receive buffers of the minimal size
The ring logic of the NTB receive buffer/transmit memory window requires
there to be at least 2 payload sized allotments.  For the minimal size
case, split the buffer into two and set the transport_mtu to the
appropriate size.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-05-15 10:57:59 -07:00
Jon Mason 90f9e93464
NTB: reset tx_index on link toggle
If the NTB link toggles, the driver could stop receiving due to the
tx_index not being set to 0 on the transmitting size on a link-up event.
This is due to the driver expecting the incoming data to start at the
beginning of the receive buffer and not at a random place.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-05-15 10:57:51 -07:00
Jon Mason b77b2637b3
NTB: Link toggle memory leak
Each link-up will allocate a new NTB receive buffer when the NTB
properties are negotiated with the remote system.  These allocations did
not check for existing buffers and thus did not free them.  Now, the
driver will check for an existing buffer and free it if not of the
correct size, before trying to alloc a new one.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-05-15 10:57:45 -07:00
Jon Mason 113fc505b8
NTB: Handle 64bit BAR sizes
64bit BAR sizes are permissible with an NTB device.  To support them
various modifications and clean-ups were required, most significantly
using 2 32bit scratch pad registers for each BAR.

Also, modify the driver to allow more than 2 Memory Windows.

Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-05-15 10:57:40 -07:00
Dan Carpenter cc0f868d8a
NTB: fix pointer math issues
->remote_rx_info and ->rx_info are struct ntb_rx_info pointers.  If we
add sizeof(struct ntb_rx_info) then it goes too far.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-05-15 10:57:29 -07:00
Dan Carpenter ad3e2751e7
ntb: off by one sanity checks
These tests are off by one.  If "mw" is equal to NTB_NUM_MW then we
would go beyond the end of the ndev->mw[] array.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-05-15 10:57:24 -07:00
Jon Mason 186f27ff9f
NTB: variable dereferenced before check
Correct instances of variable dereferencing before checking its value on
the functions exported to the client drivers.  Also, add sanity checks
for all exported functions.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jon Mason <jon.mason@intel.com>
2013-05-15 10:57:17 -07:00
Jon Mason 74465645cd NTB: Fix Sparse Warnings
Address the sparse warnings and resulting fallout

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-21 14:34:21 -08:00
Jon Mason 719234f944 NTB: disable x86_32 support
Atomic readq and writeq do not exist by default on some 32bit
architectures, thus causing compile errors due to non-existent symbols.
Since NTB has not been tested 32bit, disable x86_32 support until such
time as this and any other issues can be properly discovered.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-21 14:34:21 -08:00
Jon Mason 50228c5505 NTB: Update Version
Update NTB version to 0.25

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-20 15:48:13 -08:00
Jon Mason 448c6fb3a3 NTB: Out of free receive entries issue
If the NTB client driver enqueues the maximum number of rx buffers, it
will not be able to re-enqueue another in its callback handler due to a
lack of free entries.  This can be avoided by adding the current entry
to the free queue prior to calling the client callback handler.  With
this change, ntb_netdev will no longer encounter a rx error on its first
packet.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-20 15:45:52 -08:00
Jon Mason 793c20e9c9 NTB: Remove reads across NTB
CPU reads across NTB are slow(er) and can hang the local system if an
ECC error is encountered on the remote.  To work around the need for a
read, have the remote side write its current position in the rx buffer
to the local system's buffer and use that to see if there is room when
transmitting.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-20 15:45:51 -08:00
Jon Mason d7237e22bb NTB: correct stack usage warning in debugfs_read
Correct gcc warning of using too much stack debugfs_read.  This is done
by kmallocing the buffer instead of using the char array on stack.
Also, shrinking the buffer to something closer to what is currently
being used.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-20 15:45:51 -08:00
Jon Mason f766755c30 NTB: whitespace cleanups
Whitespace cleanups found via `indent`

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-20 15:45:51 -08:00
Jon Mason 170d35a57c NTB: namespacecheck cleanups
Declare ntb_bus_type static to remove it from name space, and remove
unused ntb_get_max_spads function.  Found via `make namespacecheck`.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-20 15:45:51 -08:00
Jon Mason d66d7ac2e0 NTB: use simple_open for debugfs
Use simple_open for debugfs instead of recreating it in the NTB driver.
Caught by coccicheck.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-20 15:45:51 -08:00
Jon Mason 7b4f2d3c3b NTB: No sleeping in interrupt context
Move all cancel_delayed_work_sync to a work thread to prevent sleeping
in interrupt context (when the NTB link goes down).  Caught via
'Sleep inside atomic section checking'

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-20 15:45:51 -08:00
Jon Mason ef114ed506 NTB: separate transmit and receive windows
Since it is possible for the memory windows on the two NTB connected
systems to be different sizes, the divergent sizes must be accounted for
in the segmentation of the MW's on each side.  Create separate size
variables and initialization as necessary.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-20 15:45:50 -08:00
Jon Mason 842c1ddea5 NTB: correct memory barrier
mmiowb is not sufficient to flush the data and is causing data
corruption.  Change to wmb and the data corruption is no more.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-20 15:45:50 -08:00
Jon Mason 8222b402e2 NTB: Handle ntb client device probes without present hardware
Attempts to probe client ntb drivers without ntb hardware present will
result in null pointer dereference due to the lack of the ntb bus device
being registers.  Check to see if this is the case, and fail all calls
by the clients registering their drivers.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-20 15:45:50 -08:00
Greg Kroah-Hartman 78a61ab79a ntb: remove __dev* markings
These are now gone from the kernel, so remove them from the newly-added
drivers before they start to cause build errors for people.

Cc: Jon Mason <jon.mason@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-17 19:17:42 -08:00
Jon Mason fce8a7bb5b PCI-Express Non-Transparent Bridge Support
A PCI-Express non-transparent bridge (NTB) is a point-to-point PCIe bus
connecting 2 systems, providing electrical isolation between the two subsystems.
A non-transparent bridge is functionally similar to a transparent bridge except
that both sides of the bridge have their own independent address domains.  The
host on one side of the bridge will not have the visibility of the complete
memory or I/O space on the other side of the bridge.  To communicate across the
non-transparent bridge, each NTB endpoint has one (or more) apertures exposed to
the local system.  Writes to these apertures are mirrored to memory on the
remote system.  Communications can also occur through the use of doorbell
registers that initiate interrupts to the alternate domain, and scratch-pad
registers accessible from both sides.

The NTB device driver is needed to configure these memory windows, doorbell, and
scratch-pad registers as well as use them in such a way as they can be turned
into a viable communication channel to the remote system.  ntb_hw.[ch]
determines the usage model (NTB to NTB or NTB to Root Port) and abstracts away
the underlying hardware to provide access and a common interface to the doorbell
registers, scratch pads, and memory windows.  These hardware interfaces are
exported so that other, non-mainlined kernel drivers can access these.
ntb_transport.[ch] also uses the exported interfaces in ntb_hw.[ch] to setup a
communication channel(s) and provide a reliable way of transferring data from
one side to the other, which it then exports so that "client" drivers can access
them.  These client drivers are used to provide a standard kernel interface
(i.e., Ethernet device) to NTB, such that Linux can transfer data from one
system to the other in a standard way.

Signed-off-by: Jon Mason <jon.mason@intel.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-17 19:11:14 -08:00