[ Upstream commit dc4cac67e1 ]
The AVerMedia CE310B is a simple composite + S-Video + stereo audio
capture card, and uses only the CX23888 to perform all of these
functions.
I've tested both video inputs and the audio interface and confirmed that
they're all working. However, there are some issues:
* Sometimes when I switch inputs the video signal turns black and can't
be recovered until the system is rebooted. I haven't been able to
determine the cause of this behavior, nor have I found a solution to
fix it or any workarounds other than rebooting.
* The card sometimes seems to have trouble syncing to the video signal,
and some of the VBI data appears as noise at the top of the frame, but
I assume that to be a result of my very noisy RF environment and the
card's unshielded input traces rather than a configuration issue.
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 574f29036f ]
Previously quirk_paxc_bridge() was applied when the iproc driver was
built-in, but not when it was compiled as a module.
This happened because it was under #ifdef CONFIG_PCIE_IPROC_PLATFORM:
PCIE_IPROC_PLATFORM=y causes CONFIG_PCIE_IPROC_PLATFORM to be defined, but
PCIE_IPROC_PLATFORM=m causes CONFIG_PCIE_IPROC_PLATFORM_MODULE to be
defined.
Move quirk_paxc_bridge() to pcie-iproc.c and drop the #ifdef so the quirk
is always applied, whether iproc is built-in or a module.
[bhelgaas: commit log, move to pcie-iproc.c, not pcie-iproc-platform.c]
Link: https://lore.kernel.org/r/20191211174511.89713-1-wei.liu@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bb1e09c4c ]
Cabling used to connect devices to USBH1 on RDU2 does not meet USB
spec cable quality and cable length requirements to operate at High
Speed, so limit the port to Full Speed only.
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd58a174e5 ]
RDU2 production units come with resistor connecting WP pin to
correpsonding GPIO DNPed for both SD card slots. Drop any WP related
configuration and mark both slots with "disable-wp".
Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d026c96b25 ]
QUSB2 PHY on msm8996 doesn't work well when autosuspend by
dwc3 core using USB2PHYCFG register is enabled. One of the
issue seen is that PHY driver reports PLL lock failure and
fails phy_init() if dwc3 core has USB2 PHY suspend enabled.
Fix this by using quirks to disable USB2 PHY LPM/suspend and
dwc3 core already takes care of explicitly suspending PHY
during suspend if quirks are specified.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Link: https://lore.kernel.org/r/20191209151501.26993-1-p.pisati@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8db60cb23 ]
Fix avc_insert() to call avc_node_kill() if we've already allocated
an AVC node and the code fails to insert the node in the cache.
Fixes: fa1aa143ac ("selinux: extended permissions for ioctls")
Reported-by: rsiddoji@codeaurora.org
Suggested-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0388a11074 ]
Add the Performance Monitoring Unit (PMU) device tree node to the H3
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on an OrangePi Zero.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7aa9b9eb7d ]
Add the Performance Monitoring Unit (PMU) device tree node to the H6
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.
Tested with perf record and taskset on a Pine H64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0188d5c025 ]
commit bda0be7ad9 ("security: make inode_follow_link RCU-walk aware")
passed down the rcu flag to the SELinux AVC, but failed to adjust the
test in slow_avc_audit() to also return -ECHILD on LSM_AUDIT_DATA_DENTRY.
Previously, we only returned -ECHILD if generating an audit record with
LSM_AUDIT_DATA_INODE since this was only relevant from inode_permission.
Move the handling of MAY_NOT_BLOCK to avc_audit() and its inlined
equivalent in selinux_inode_permission() immediately after we determine
that audit is required, and always fall back to ref-walk in this case.
Fixes: bda0be7ad9 ("security: make inode_follow_link RCU-walk aware")
Reported-by: Will Deacon <will@kernel.org>
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 718eae277e ]
Convert cpu_to_le16(le16_to_cpu(frame->datalen) + len) to
use le16_add_cpu(), which is more concise and does the same thing.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 148587a59f ]
Qiang Zhao points out that these offsets get written to 16-bit
registers, and there are some QE platforms with more than 64K
muram. So it is possible that qe_muram_alloc() gives us an allocation
that can't actually be used by the hardware, so detect and reject
that.
Reported-by: Qiang Zhao <qiang.zhao@nxp.com>
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8a039d377 ]
RK808 can leverage a couple of GPIOs to tweak the ramp rate during DVS
(Dynamic Voltage Scaling). These GPIOs are entirely optional but a
dev_warn() appeared when cleaning this driver to use a more up-to-date
gpiod API. At least reduce the log level to 'info' as it is totally
fine to not populate these GPIO on a hardware design.
This change is trivial but it is worth not polluting the logs during
bringup phase by having real warnings and errors sorted out
correctly.
Fixes: a13eaf02e2 ("regulator: rk808: make better use of the gpiod API")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191203164709.11127-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a63141e317 ]
Commit b0f3cd3191 ("drm/amdgpu: remove unnecessary JPEG2.0 code from
VCN2.0") introduced a new clang warning in the vcn_v2_0_stop function:
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1082:2: warning: variable 'r'
is used uninitialized whenever 'while' loop exits because its condition
is false [-Wsometimes-uninitialized]
SOC15_WAIT_ON_RREG(VCN, 0, mmUVD_STATUS, UVD_STATUS__IDLE, 0x7, r);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/../amdgpu/soc15_common.h:55:10: note:
expanded from macro 'SOC15_WAIT_ON_RREG'
while ((tmp_ & (mask)) != (expected_value)) { \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1083:6: note: uninitialized use
occurs here
if (r)
^
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1082:2: note: remove the
condition if it is always true
SOC15_WAIT_ON_RREG(VCN, 0, mmUVD_STATUS, UVD_STATUS__IDLE, 0x7, r);
^
../drivers/gpu/drm/amd/amdgpu/../amdgpu/soc15_common.h:55:10: note:
expanded from macro 'SOC15_WAIT_ON_RREG'
while ((tmp_ & (mask)) != (expected_value)) { \
^
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1072:7: note: initialize the
variable 'r' to silence this warning
int r;
^
= 0
1 warning generated.
To prevent warnings like this from happening in the future, make the
SOC15_WAIT_ON_RREG macro initialize its ret variable before the while
loop that can time out. This macro's return value is always checked so
it should set ret in both the success and fail path.
Link: https://github.com/ClangBuiltLinux/linux/issues/776
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bae028e3e5 ]
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c: In function
'amdgpu_atombios_get_connector_info_from_object_table':
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:26: warning: variable
'grph_obj_num' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:13: warning: variable
'grph_obj_id' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:37: warning: variable
'con_obj_type' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:24: warning: variable
'con_obj_num' set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Fixes: d38ceaf99e ("drm/amdgpu: add core driver (v4)")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 908b050114 ]
When I got my clock parenting slightly wrong I ended up with a crash
that looked like this:
Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000000
...
pc : clk_hw_get_rate+0x14/0x44
...
Call trace:
clk_hw_get_rate+0x14/0x44
_freq_tbl_determine_rate+0x94/0xfc
clk_rcg2_determine_rate+0x2c/0x38
clk_core_determine_round_nolock+0x4c/0x88
clk_core_round_rate_nolock+0x6c/0xa8
clk_core_round_rate_nolock+0x9c/0xa8
clk_core_set_rate_nolock+0x70/0x180
clk_set_rate+0x3c/0x6c
of_clk_set_defaults+0x254/0x360
platform_drv_probe+0x28/0xb0
really_probe+0x120/0x2dc
driver_probe_device+0x64/0xfc
device_driver_attach+0x4c/0x6c
__driver_attach+0xac/0xc0
bus_for_each_dev+0x84/0xcc
driver_attach+0x2c/0x38
bus_add_driver+0xfc/0x1d0
driver_register+0x64/0xf8
__platform_driver_register+0x4c/0x58
msm_drm_register+0x5c/0x60
...
It turned out that clk_hw_get_parent_by_index() was returning NULL and
we weren't checking. Let's check it so that we don't crash.
Fixes: ac269395cd ("clk: qcom: Convert to clk_hw based provider APIs")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lkml.kernel.org/r/20200203103049.v4.1.I7487325fe8e701a68a07d3be8a6a4b571eca9cfa@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8fb7d7e48 ]
Running randconfig on arm64 using KCONFIG_SEED=0x40C5E904 (e.g. on v5.5)
produces the .config with CONFIG_EFI=y and CONFIG_CPU_BIG_ENDIAN=y,
which does not meet the !CONFIG_CPU_BIG_ENDIAN dependency.
This is because the user choice for CONFIG_CPU_LITTLE_ENDIAN vs
CONFIG_CPU_BIG_ENDIAN is set by randomize_choice_values() after the
value of CONFIG_EFI is calculated.
When this happens, the has_changed flag should be set.
Currently, it takes the result from the last iteration. It should
accumulate all the results of the loop.
Fixes: 3b9a19e089 ("kconfig: loop as long as we changed some symbols in randconfig")
Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c0dd228b5 ]
When kzalloc fail, may cause trying to destroy the
workqueue from inside the workqueue.
If num_connections is m (2 < m), and NO.1 ~ NO.n
(1 < n < m) kzalloc are successful. The NO.(n + 1)
failed. Then, nbd_start_device will return ENOMEM
to nbd_start_device_ioctl, and nbd_start_device_ioctl
will return immediately without running flush_workqueue.
However, we still have n recv threads. If nbd_release
run first, recv threads may have to drop the last
config_refs and try to destroy the workqueue from
inside the workqueue.
To fix it, add a flush_workqueue in nbd_start_device.
Fixes: e9e006f5fc ("nbd: fix max number of supported devs")
Signed-off-by: Sun Ke <sunke32@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3eb6d7aca5 ]
[WHY]
Two years ago the patch referenced by the Fixes tag stopped running
dp_verify_link_cap_with_retries during DP detection when the reason
for the detection was a short-pulse interrupt. This effectively meant
that we were no longer doing the verify_link_cap training on active
dongles when their SINK_COUNT changed from 0 to 1.
A year ago this was partly remedied with:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
This made sure that we trained the dongle on initial hotplug (without
connected downstream devices).
This is all fine and dandy if it weren't for the fact that there are
some dongles on the market that don't like link training when SINK_COUNT
is 0 These dongles will in fact indicate a SINK_COUNT of 0 immediately
after hotplug, even when a downstream device is connected, and then
trigger a shortpulse interrupt indicating a SINK_COUNT change to 1.
In order to play nicely we will need our policy to not link train an
active DP dongle when SINK_COUNT is 0 but ensure we train it when the
SINK_COUNT changes to 1.
[HOW]
Call dp_verify_link_cap_with_retries on detection even when the detection
is triggered from a short pulse interrupt.
With this change we can also revert this commit which we'll do in a separate
follow-up change:
commit 80adaebd2d ("drm/amd/display: Don't skip link training for empty dongle")
Fixes: 0301ccbaf6 ("drm/amd/display: DP Compliance 400.1.1 failure")
Suggested-by: Louis Li <Ching-shih.Li@amd.com>
Tested-by: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ba8b3b6bd ]
The management packets, send to firmware via WMI, are
mapped using the direction DMA_TO_DEVICE. Currently in
case of wmi cleanup, these buffers are being unmapped
using an incorrect DMA direction. This can cause unwanted
behavior when the host driver is handling a restart
of the wlan firmware.
We might see a trace like below
[<ffffff8008098b18>] __dma_inv_area+0x28/0x58
[<ffffff8001176734>] ath10k_wmi_mgmt_tx_clean_up_pending+0x60/0xb0 [ath10k_core]
[<ffffff80088c7c50>] idr_for_each+0x78/0xe4
[<ffffff80011766a4>] ath10k_wmi_detach+0x4c/0x7c [ath10k_core]
[<ffffff8001163d7c>] ath10k_core_stop+0x58/0x68 [ath10k_core]
[<ffffff800114fb74>] ath10k_halt+0xec/0x13c [ath10k_core]
[<ffffff8001165110>] ath10k_core_restart+0x11c/0x1a8 [ath10k_core]
[<ffffff80080c36bc>] process_one_work+0x16c/0x31c
Fix the incorrect DMA direction during the wmi
management tx buffer cleanup.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: dc405152bb ("ath10k: handle mgmt tx completion event")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51f57b01e4 ]
JBD2_REC_ERR flag used to indicate the errno has been updated when jbd2
aborted, and then __ext4_abort() and ext4_handle_error() can invoke
panic if ERRORS_PANIC is specified. But if the journal has been aborted
with zero errno, jbd2_journal_abort() didn't set this flag so we can
no longer panic. Fix this by always record the proper errno in the
journal superblock.
Fixes: 4327ba52af ("ext4, jbd2: ensure entering into panic after recording an error in superblock")
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20191204124614.45424-3-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc420c6cee ]
Kmemleak relies on specific symbols to register the read only data
during init (e.g. __start_ro_after_init).
Trying to build an XIP kernel on arm results in the linking error
reported below because when this option is selected read only data
after init are not allowed since .data is read only (.rodata).
arm-linux-gnueabihf-ld: mm/kmemleak.o: in function `kmemleak_init':
kmemleak.c:(.init.text+0x148): undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x14c):
undefined reference to `__end_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x150):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x156):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x162):
undefined reference to `__start_ro_after_init'
arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x16a):
undefined reference to `__start_ro_after_init'
linux/Makefile:1078: recipe for target 'vmlinux' failed
Fix the issue enabling kmemleak only on non XIP kernels.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfb6cd1e65 ]
Looking through old emails in my INBOX, I came across a patch from Luis
Henriques that attempted to fix a race of two stat tracers registering the
same stat trace (extremely unlikely, as this is done in the kernel, and
probably doesn't even exist). The submitted patch wasn't quite right as it
needed to deal with clean up a bit better (if two stat tracers were the
same, it would have the same files).
But to make the code cleaner, all we needed to do is to keep the
all_stat_sessions_mutex held for most of the registering function.
Link: http://lkml.kernel.org/r/1410299375-20068-1-git-send-email-luis.henriques@canonical.com
Fixes: 002bb86d8d ("tracing/ftrace: separate events tracing and stats tracing engine")
Reported-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afccc00f75 ]
tracing_stat_init() was always returning '0', even on the error paths. It
now returns -ENODEV if tracing_init_dentry() fails or -ENOMEM if it fails
to created the 'trace_stat' debugfs directory.
Link: http://lkml.kernel.org/r/1410299381-20108-1-git-send-email-luis.henriques@canonical.com
Fixes: ed6f1c996b ("tracing: Check return value of tracing_init_dentry()")
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
[ Pulled from the archeological digging of my INBOX ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 965c94f309 ]
An ioda_pe for each VF is allocated in pnv_pci_sriov_enable() before
the pci_dev for the VF is created. We need to set the pe->pdev pointer
at some point after the pci_dev is created. Currently we do that in:
pcibios_bus_add_device()
pnv_pci_dma_dev_setup() (via phb->ops.dma_dev_setup)
/* fixup is done here */
pnv_pci_ioda_dma_dev_setup() (via pnv_phb->dma_dev_setup)
The fixup needs to be done before setting up DMA for for the VF's PE,
but there's no real reason to delay it until this point. Move the
fixup into pnv_pci_ioda_fixup_iov() so the ordering is:
pcibios_add_device()
pnv_pci_ioda_fixup_iov() (via ppc_md.pcibios_fixup_sriov)
pcibios_bus_add_device()
...
This isn't strictly required, but it's a slightly more logical place
to do the fixup and it simplifies pnv_pci_dma_dev_setup().
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200110070207.439-4-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4cf7aa57e ]
Instead of doing error handling in the middle of ->probe(), move error
handling and freeing the reference to timer to the end.
This fixes a resource leak as dm_timer wasn't freed when allocating
*omap failed.
Implementation note: The put: label was never reached without a goto and
ret being unequal to 0, so the removed return statement is fine.
Fixes: 6604c6556d ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dacc909233 ]
When checking whether the reported lfb_size makes sense, the height
* stride result is page-aligned before seeing whether it exceeds the
reported size.
This doesn't work if height * stride is not an exact number of pages.
For example, as reported in the kernel bugzilla below, an 800x600x32 EFI
framebuffer gets skipped because of this.
Move the PAGE_ALIGN to after the check vs size.
Reported-by: Christopher Head <chead@chead.ca>
Tested-by: Christopher Head <chead@chead.ca>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206051
Link: https://lkml.kernel.org/r/20200107230410.2291947-1-nivedita@alum.mit.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a09decff5c ]
If the journal is dirty when the filesystem is mounted, jbd2 will replay
the journal but the journal superblock will not be updated by
journal_reset() because JBD2_ABORT flag is still set (it was set in
journal_init_common()). This is problematic because when a new transaction
is then committed, it will be recorded in block 1 (journal->j_tail was set
to 1 in journal_reset()). If unclean shutdown happens again before the
journal superblock is updated, the new recorded transaction will not be
replayed during the next mount (because of stale sb->s_start and
sb->s_sequence values) which can lead to filesystem corruption.
Fixes: 85e0c4e89c ("jbd2: if the journal is aborted then don't allow update of the log tail")
Signed-off-by: Kai Li <li.kai4@h3c.com>
Link: https://lore.kernel.org/r/20200111022542.5008-1-li.kai4@h3c.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b64a650f0 ]
It was observed[1] on arm64 that __builtin_strlen led to an infinite
loop in the get_size selftest. This is because __builtin_strlen (and
other builtins) may sometimes result in a call to the C library
function. The C library implementation of strlen uses an IFUNC
resolver to load the most efficient strlen implementation for the
underlying machine and hence has a PLT indirection even for static
binaries. Because this binary avoids the C library startup routines,
the PLT initialization never happens and hence the program gets stuck
in an infinite loop.
On x86_64 the __builtin_strlen just happens to expand inline and avoid
the call but that is not always guaranteed.
Further, while testing on x86_64 (Fedora 31), it was observed that the
test also failed with a segfault inside write() because the generated
code for the write function in glibc seems to access TLS before the
syscall (probably due to the cancellation point check) and fails
because TLS is not initialised.
To mitigate these problems, this patch reduces the interface with the
C library to just the syscall function. The syscall function still
sets errno on failure, which is undesirable but for now it only
affects cases where syscalls fail.
[1] https://bugs.linaro.org/show_bug.cgi?id=5479
Signed-off-by: Siddhesh Poyarekar <siddhesh@gotplt.org>
Reported-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Tim Bird <tim.bird@sony.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2052d032c0 ]
Currently when setup_irq fails the error exit path will leak the
recently allocated timer structure. Originally the code would
throw a panic but a later commit changed the behaviour to return
via the err_iounmap path and hence we now have a memory leak. Fix
this by adding a err_timer_free error path that kfree's timer.
Addresses-Coverity: ("Resource Leak")
Fixes: 524a7f0898 ("clocksource/drivers/bcm2835_timer: Convert init function to return error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191219213246.34437-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c1ed62ae0 ]
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/usb/gadget/udc/core.c, 1175:
kzalloc(GFP_KERNEL) in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/core.c, 1195:
mutex_lock in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 212:
debugfs_create_file in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2197:
gr_dfs_create in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2114:
devm_request_threaded_irq in gr_request_irq
drivers/usb/gadget/udc/gr_udc.c, 2202:
gr_request_irq in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe
kzalloc(GFP_KERNEL), mutex_lock(), debugfs_create_file() and
devm_request_threaded_irq() can sleep at runtime.
To fix these possible bugs, usb_add_gadget_udc(), gr_dfs_create() and
gr_request_irq() are called without handling the spinlock.
These bugs are found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b74351287d ]
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
kernel/irq/manage.c, 523:
synchronize_irq in disable_irq
drivers/uio/uio_dmem_genirq.c, 140:
disable_irq in uio_dmem_genirq_irqcontrol
drivers/uio/uio_dmem_genirq.c, 134:
_raw_spin_lock_irqsave in uio_dmem_genirq_irqcontrol
synchronize_irq() can sleep at runtime.
To fix this bug, disable_irq() is called without holding the spinlock.
This bug is found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20191218094405.6009-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 548f0b9a5f ]
This fixes build errors of all sorts.
Also, emit .exit.text unconditionally.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffc2760bcf ]
Fix a couple of issues with the way we map and copy the vendor string:
- we map only 2 bytes, which usually works since you get at least a
page, but if the vendor string happens to cross a page boundary,
a crash will result
- only call early_memunmap() if early_memremap() succeeded, or we will
call it with a NULL address which it doesn't like,
- while at it, switch to early_memremap_ro(), and array indexing rather
than pointer dereferencing to read the CHAR16 characters.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Matthew Garrett <mjg59@google.com>
Cc: linux-efi@vger.kernel.org
Fixes: 5b83683f32 ("x86: EFI runtime service support")
Link: https://lkml.kernel.org/r/20200103113953.9571-5-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a23680594d ]
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.
This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.
This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().
Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb6d42061a ]
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/media/platform/sti/bdisp/bdisp-hw.c, 385:
msleep in bdisp_hw_reset
drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 341:
bdisp_hw_reset in bdisp_device_run
drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 317:
_raw_spin_lock_irqsave in bdisp_device_run
To fix this bug, msleep() is replaced with udelay().
This bug is found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39d630e332 ]
PASID allocator uses IDR which is exclusive for the end of the
allocation range. There is no need to decrement pasid_max.
Fixes: af39507305 ("iommu/vt-d: Apply global PASID in SVA")
Reported-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e36eaf94be ]
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/gpio/gpio-grgpio.c, 261:
request_irq in grgpio_irq_map
drivers/gpio/gpio-grgpio.c, 255:
_raw_spin_lock_irqsave in grgpio_irq_map
drivers/gpio/gpio-grgpio.c, 318:
free_irq in grgpio_irq_unmap
drivers/gpio/gpio-grgpio.c, 299:
_raw_spin_lock_irqsave in grgpio_irq_unmap
request_irq() and free_irq() can sleep at runtime.
To fix these bugs, request_irq() and free_irq() are called without
holding the spinlock.
These bugs are found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20191218132605.10594-1-baijiaju1990@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b5b9997b3 ]
On pseries there is a bug with adding hotplugged devices to an IOMMU
group. For a number of dumb reasons fixing that bug first requires
re-working how VFs are configured on PowerNV. For background, on
PowerNV we use the pcibios_sriov_enable() hook to do two things:
1. Create a pci_dn structure for each of the VFs, and
2. Configure the PHB's internal BARs so the MMIO range for each VF
maps to a unique PE.
Roughly speaking a PE is the hardware counterpart to a Linux IOMMU
group since all the devices in a PE share the same IOMMU table. A PE
also defines the set of devices that should be isolated in response to
a PCI error (i.e. bad DMA, UR/CA, AER events, etc). When isolated all
MMIO and DMA traffic to and from devicein the PE is blocked by the
root complex until the PE is recovered by the OS.
The requirement to block MMIO causes a giant headache because the P8
PHB generally uses a fixed mapping between MMIO addresses and PEs. As
a result we need to delay configuring the IOMMU groups for device
until after MMIO resources are assigned. For physical devices (i.e.
non-VFs) the PE assignment is done in pcibios_setup_bridge() which is
called immediately after the MMIO resources for downstream
devices (and the bridge's windows) are assigned. For VFs the setup is
more complicated because:
a) pcibios_setup_bridge() is not called again when VFs are activated, and
b) The pci_dev for VFs are created by generic code which runs after
pcibios_sriov_enable() is called.
The work around for this is a two step process:
1. A fixup in pcibios_add_device() is used to initialised the cached
pe_number in pci_dn, then
2. A bus notifier then adds the device to the IOMMU group for the PE
specified in pci_dn->pe_number.
A side effect fixing the pseries bug mentioned in the first paragraph
is moving the fixup out of pcibios_add_device() and into
pcibios_bus_add_device(), which is called much later. This results in
step 2. failing because pci_dn->pe_number won't be initialised when
the bus notifier is run.
We can fix this by removing the need for the fixup. The PE for a VF is
known before the VF is even scanned so we can initialise
pci_dn->pe_number pcibios_sriov_enable() instead. Unfortunately,
moving the initialisation causes two problems:
1. We trip the WARN_ON() in the current fixup code, and
2. The EEH core clears pdn->pe_number when recovering a VF and
relies on the fixup to correctly re-set it.
The only justification for either of these is a comment in
eeh_rmv_device() suggesting that pdn->pe_number *must* be set to
IODA_INVALID_PE in order for the VF to be scanned. However, this
comment appears to have no basis in reality. Both bugs can be fixed by
just deleting the code.
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191028085424.12006-1-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1451d5ae35 ]
This driver supports both the mt9v032 (color) and the mt9v022 (mono)
sensors. Depending on which sensor is used, the format from the sensor is
different. The format.code inside the dev struct holds this information.
The enum mbus and enum frame sizes need to take into account both type of
sensors, not just the color one. To solve this, use the format.code in
these functions instead of the hardcoded bayer color format (which is only
used for mt9v032).
[Sakari Ailus: rewrapped commit message]
Suggested-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c911fe799 ]
In the probe function, some resources are allocated using 'dma_alloc_wc()',
they should be released with 'dma_free_wc()', not 'dma_free_coherent()'.
We already use 'dma_free_wc()' in the remove function, but not in the
error handling path of the probe function.
Also, remove a useless 'PAGE_ALIGN()'. 'info->fix.smem_len' is already
PAGE_ALIGNed.
Fixes: 638772c755 ("fb: add support of LCD display controller on pxa168/910 (base layer)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
CC: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190831100024.3248-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55b1cb1f03 ]
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
two CAN outputs.
Fix this by:
- Renaming CRX0_CRX1_MARK to CTX0_CTX1_MARK, as PJ2MD[2:0]=010
configures the combined "CTX0&CTX1" output signal,
- Renaming CRX0X1_MARK to CRX0_CRX1_MARK, as PJ3MD[1:0]=10 configures
the shared "CRX0/CRX1" input signal, which is fed to both CAN
inputs,
- Adding the missing function GPIO definition for "CTX0&CTX1" to
pinmux_func_gpios[],
- Moving all CAN enums next to each other.
See SH7262 Group, SH7264 Group User's Manual: Hardware, Rev. 4.00:
[1] Figure 1.2 (3) (Pin Assignment for the SH7264 Group (1-Mbyte
Version),
[2] Figure 1.2 (4) Pin Assignment for the SH7264 Group (640-Kbyte
Version,
[3] Table 1.4 List of Pins,
[4] Figure 20.29 Connection Example when Using This Module as 1-Channel
Module (64 Mailboxes x 1 Channel),
[5] Table 32.10 Multiplexed Pins (Port J),
[6] Section 32.2.30 (3) Port J Control Register 0 (PJCR0).
Note that the last 2 disagree about PJ2MD[2:0], which is probably the
root cause of this bug. But considering [4], "CTx0&CTx1" in [5] must
be correct, and "CRx0&CRx1" in [6] must be wrong.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c26a2c2ddc ]
The driver wrongly assumes that it is the only entity that can set the
SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the
gfar_clean_tx_ring function, where the TX timestamp is collected if
necessary, the aforementioned bit is used to discriminate whether or not
the TX timestamp should be delivered to the socket's error queue.
But a stacked driver such as a DSA switch can also set the
SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in
order to denote that the hardware timestamping process is undergoing.
Therefore, gianfar would misinterpret the "in progress" bit as being its
own, and deliver a second skb clone in the socket's error queue,
completely throwing off a PTP process which is not expecting to receive
it, _even though_ TX timestamping is not enabled for gianfar.
There have been discussions [0] as to whether non-MAC drivers need or
not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2
timestamps, a sw and a hw one, to applications which only expect one).
But as of this patch, there are at least 2 PTP drivers that would break
in conjunction with gianfar: the sja1105 DSA switch and the felix
switch, by way of its ocelot core driver.
So regardless of that conclusion, fix the gianfar driver to not do stuff
based on flags set by others and not intended for it.
[0]: https://www.spinics.net/lists/netdev/msg619699.html
Fixes: f0ee7acfcd ("gianfar: Add hardware TX timestamping support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d61fe22c2a ]
A design of ALSA control core allows applications to execute three
operations for TLV feature; read, write and command. Furthermore, it
allows driver developers to process the operations by two ways; allocated
array or callback function. In the former, read operation is just allowed,
thus developers uses the latter when device driver supports variety of
models or the target model is expected to dynamically change information
stored in TLV container.
The core also allows applications to lock any element so that the other
applications can't perform write operation to the element for element
value and TLV information. When the element is locked, write and command
operation for TLV information are prohibited as well as element value.
Any read operation should be allowed in the case.
At present, when an element has callback function for TLV information,
TLV read operation returns EPERM if the element is locked. On the
other hand, the read operation is success when an element has allocated
array for TLV information. In both cases, read operation is success for
element value expectedly.
This commit fixes the bug. This change can be backported to v4.14
kernel or later.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20191223093347.15279-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f629afe336 ]
Apparently our current rwsem code doesn't like doing the trylock, then
lock for real scheme. So change our dax read/write methods to just do the
trylock for the RWF_NOWAIT case.
This seems to fix AIM7 regression in some scalable filesystems upto ~25%
in some cases. Claimed in commit 942491c9e6 ("xfs: fix AIM7 regression")
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Matthew Bobrowski <mbobrowski@mbobrowski.org>
Tested-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
Link: https://lore.kernel.org/r/20191212055557.11151-2-riteshh@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 697529091a ]
Before commit bb29b9cccd ("leds: pca963x: Add bindings to invert
polarity") Mode register 2 was initialized directly with either 0x01
or 0x05 for open-drain or totem pole (push-pull) configuration.
Afterwards, MODE2 initialization started using bitwise operations on
top of the default MODE2 register value (0x05). Using bitwise OR for
setting OUTDRV with 0x01 and 0x05 does not produce correct results.
When open-drain is used, instead of setting OUTDRV to 0, the driver
keeps it as 1:
Open-drain: 0x05 | 0x01 -> 0x05 (0b101 - incorrect)
Totem pole: 0x05 | 0x05 -> 0x05 (0b101 - correct but still wrong)
Now OUTDRV setting uses correct bitwise operations for initialization:
Open-drain: 0x05 & ~0x04 -> 0x01 (0b001 - correct)
Totem pole: 0x05 | 0x04 -> 0x05 (0b101 - correct)
Additional MODE2 register definitions are introduced now as well.
Fixes: bb29b9cccd ("leds: pca963x: Add bindings to invert polarity")
Signed-off-by: Zahari Petkov <zahari@balena.io>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>