Pull irq updates from Ingo Molnar:
"Most of the IRQ subsystem changes in this cycle were irq-chip driver
updates:
- Qualcomm PDC wakeup interrupt support
- Layerscape external IRQ support
- Broadcom bcm7038 PM and wakeup support
- Ingenic driver cleanup and modernization
- GICv3 ITS preparation for GICv4.1 updates
- GICv4 fixes
There's also the series from Frederic Weisbecker that fixes memory
ordering bugs for the irq-work logic, whose primary fix is to turn
work->irq_work.flags into an atomic variable and then convert the
complex (and buggy) atomic_cmpxchg() loop in irq_work_claim() into a
much simpler atomic_fetch_or() call.
There are also various smaller cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
pinctrl/sdm845: Add PDC wakeup interrupt map for GPIOs
pinctrl/msm: Setup GPIO chip in hierarchy
irqchip/qcom-pdc: Add irqchip set/get state calls
irqchip/qcom-pdc: Add irqdomain for wakeup capable GPIOs
irqchip/qcom-pdc: Do not toggle IRQ_ENABLE during mask/unmask
irqchip/qcom-pdc: Update max PDC interrupts
of/irq: Document properties for wakeup interrupt parent
genirq: Introduce irq_chip_get/set_parent_state calls
irqdomain: Add bus token DOMAIN_BUS_WAKEUP
genirq: Fix function documentation of __irq_alloc_descs()
irq_work: Fix IRQ_WORK_BUSY bit clearing
irqchip/ti-sci-inta: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
irq_work: Slightly simplify IRQ_WORK_PENDING clearing
irq_work: Fix irq_work_claim() memory ordering
irq_work: Convert flags to atomic_t
irqchip: Ingenic: Add process for more than one irq at the same time.
irqchip: ingenic: Alloc generic chips from IRQ domain
irqchip: ingenic: Get virq number from IRQ domain
irqchip: ingenic: Error out if IRQ domain creation failed
irqchip: ingenic: Drop redundant irq_suspend / irq_resume functions
...
series:
Core changes:
- Avoid taking direct references to device tree-supplied
device names: these may changed at runtime under certain
circumstances to kstrdup them.
GPIO related:
- Work is ongoing to move to passing the irqchip along as a
templated struct gpio_irq_chip when adding a standard
gpiolib-based irqchip to a GPIO controller, a few patches
in this cycle switches a few pin control drivers over to
using this method.
New hardware support:
- Intel Lightning Mountain SoC pin controller and GPIO
support, a first Intel platform to use device tree rather
than ACPI to configure the system. News reports says that
this SoC is a network processor.
- Qualcomm MSM8976 and MSM8956
- Qualcomm PMIC GPIO now also supports PM6150 and PM6150L
- Qualcomm SPMI MPP and SPMI GPIO for PM8950 and PMI8950
- Rockchip RK3308
- Renesas R8A77961
- Allwinner Meson-A1
Driver improvements:
- get_multiple and set_multiple support for the AT91-PIO4 driver.
- Convert Qualcomm SSBI GPIO to use the hierarchical IRQ helpers
in the GPIOlib irqchip.
-----BEGIN PGP SIGNATURE-----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=uPLY
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for v5.5.
It is pretty much business as usual, the most interesting thing I
think is the pin controller for a new Intel chip called Lightning
Mountain, which is according to news reports some kind of embedded
network processor and what is surprising about it is that Intel have
decided to use device tree to describe the system rather than ACPI
that they have traditionally favored.
Core changes:
- Avoid taking direct references to device tree-supplied device
names: these may changed at runtime under certain circumstances to
kstrdup them.
GPIO related:
- Work is ongoing to move to passing the irqchip along as a templated
struct gpio_irq_chip when adding a standard gpiolib-based irqchip
to a GPIO controller, a few patches in this cycle switches a few
pin control drivers over to using this method.
New hardware support:
- Intel Lightning Mountain SoC pin controller and GPIO support, a
first Intel platform to use device tree rather than ACPI to
configure the system. News reports says that this SoC is a network
processor.
- Qualcomm MSM8976 and MSM8956
- Qualcomm PMIC GPIO now also supports PM6150 and PM6150L
- Qualcomm SPMI MPP and SPMI GPIO for PM8950 and PMI8950
- Rockchip RK3308
- Renesas R8A77961
- Allwinner Meson-A1
Driver improvements:
- get_multiple and set_multiple support for the AT91-PIO4 driver.
- Convert Qualcomm SSBI GPIO to use the hierarchical IRQ helpers in
the GPIOlib irqchip"
* tag 'pinctrl-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (93 commits)
pinctrl: ingenic: Add OTG VBUS pin for the JZ4770
pinctrl: ingenic: Handle PIN_CONFIG_OUTPUT config
pinctrl: Fix Kconfig indentation
pinctrl: lewisburg: Update pin list according to v1.1v6
MAINTAINERS: Replace my email by one @kernel.org
pinctrl: armada-37xx: Fix irq mask access in armada_37xx_irq_set_type()
dt-bindings: pinctrl: intel: Add for new SoC
pinctrl: Add pinmux & GPIO controller driver for a new SoC
pinctrl: rza1: remove unnecessary static inline function
pinctrl: meson: add pinctrl driver support for Meson-A1 SoC
pinctrl: meson: add a new callback for SoCs fixup
pinctrl: nomadik: db8500: Add mc0_a_2 pin group without direction control
dt-bindings: pinctrl: Convert generic pin mux and config properties to schema
pinctrl: cherryview: Missed type change to unsigned int
pinctrl: intel: Missed type change to unsigned int
pinctrl: use devm_platform_ioremap_resource() to simplify code
pinctrl: just return if no valid maps
dt-bindings: pinctrl: qcom-pmic-mpp: Add support for PM/PMI8950
pinctrl: qcom: spmi-mpp: Add PM/PMI8950 compatible strings
dt-bindings: pinctrl: qcom-pmic-gpio: Add support for PM/PMI8950
...
This makes the driver support the 'output-low' and 'output-high'
devicetree properties in gpio-hog sub-nodes.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20191119155211.102527-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1574306382-32516-1-git-send-email-krzk@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Version 1.1v6 of pin list has some changes in pin names for Intel Lewisburg.
Update the driver accordingly.
Note, it reveals the bug in the driver that misses two pins in GPP_L and
has rather two extra ones. That's why the ordering of some groups is changed.
Fixes: e480b74538 ("pinctrl: intel: Add Intel Lewisburg GPIO support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191120133739.54332-1-andriy.shevchenko@linux.intel.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As explained in the following commit a9a1a48336 ("pinctrl:
armada-37xx: Fix gpio interrupt setup") the armada_37xx_irq_set_type()
function can be called before the initialization of the mask field.
That means that we can't use this field in this function and need to
workaround it using hwirq.
Fixes: 30ac0d3b07 ("pinctrl: armada-37xx: Add edge both type gpio irq support")
Cc: stable@vger.kernel.org
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191115155752.2562-1-gregory.clement@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Lightning Mountain SoC has a pinmux controller & GPIO controller IP which
controls pin multiplexing & configuration including GPIO functions selection &
GPIO attributes configuration.
This IP is not based on & does not have anything in common with Chassis
specification. The pinctrl drivers under pinctrl/intel/* are all based upon
Chassis spec compliant pinctrl IPs. So this driver doesn't fit & can not use
pinctrl framework under pinctrl/intel/* and it requires a separate new driver.
Add a new GPIO & pin control framework based driver for this IP.
Signed-off-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Link: https://lore.kernel.org/r/33e649758b70490f01724a887c490d5008c7656d.1573797249.git.rahul.tanwar@linux.intel.com
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Having static inline oneliner does not benefit too much when it is
only called from another oneliner function. Remove some of the
'onion'. This simplifies also the coming usage of the gpiolib
defines. We can do conversion from chip bits to gpiolib direction
defines as last step in the get_direction callback. Drivers can
use chip specific values in driver internal functions and do
conversion only once.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191113071045.GA22110@localhost.localdomain
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Meson A1 SoC share the same register layout of pinmux with previous
Meson-G12A, however there is difference for gpio and pin config register
in A1. The main difference is that registers before A1 are grouped by
function while those of A1 are by bank. The new register layout is as
below:
/* first bank */ /* addr */
- P_PADCTRL_GPIOP_I base + 0x00 << 2
- P_PADCTRL_GPIOP_O base + 0x01 << 2
- P_PADCTRL_GPIOP_OEN base + 0x02 << 2
- P_PADCTRL_GPIOP_PULL_EN base + 0x03 << 2
- P_PADCTRL_GPIOP_PULL_UP base + 0x04 << 2
- P_PADCTRL_GPIOP_DS base + 0x05 << 2
/* second bank */
- P_PADCTRL_GPIOB_I base + 0x10 << 2
- P_PADCTRL_GPIOB_O base + 0x11 << 2
- P_PADCTRL_GPIOB_OEN base + 0x12 << 2
- P_PADCTRL_GPIOB_PULL_EN base + 0x13 << 2
- P_PADCTRL_GPIOB_PULL_UP base + 0x14 << 2
- P_PADCTRL_GPIOB_DS base + 0x15 << 2
Each bank contains at least 6 registers to be configured, if one bank
has more than 16 gpios, an extra P_PADCTRL_GPIO[X]_DS_EXT is included.
Between two adjacent P_PADCTRL_GPIO[X]_I, there is an offset 0x10, that
is to say, for third bank, the offsets will be 0x20,0x21,0x22,0x23,0x24
,0x25 according to above register layout. For previous chips, registers
are grouped according to their functions while registers of A1 are
according to bank.Also note that there is no AO bank any more in A1.
Current Meson pinctrl driver can cover such change by using base address
of GPIO as that of drive-strength. While simply giving reg_ds = reg_pullen
make wrong value to reg_ds for Socs that do not support drive-strength
like AXG.To make things simple, add an extra dt parser function for
a1 and remain the old dt parser function for only reg parsing.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/1573819429-6937-3-git-send-email-qianggui.song@amlogic.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In meson_pinctrl_parse_dt, it contains two parts: reg parsing and
SoC relative fixup for AO. Several fixups in the same code make it hard
to maintain, so move all fixups to each SoC's callback and make
meson_pinctrl_parse_dt just do the reg parsing, separate these two
parts.Overview of all current Meson SoCs fixup is as below:
+------+--------------------------------------+--------------------------+
| | | |
| SoC | EE domain | AO domain |
+------+--------------------------------------+--------------------------+
|m8 | parse regs: | parse regs: |
|m8b | gpio,mux,pull,pull-enable(skip ds) | gpio,mux,pull(skip ds)|
|gxl | fixup: | fixup: |
|gxbb | no | pull-enable = pull; |
|axg | | |
+------+--------------------------------------+--------------------------+
|g12a | parse regs: | parse regs: |
|sm1 | gpio,mux,pull,pull-enable,ds | gpio,mux,ds |
| | fixup: | fixup: |
| | no | pull = gpio; |
| | | pull-enable = gpio; |
+------+--------------------------------------+--------------------------+
|a1 or | parse regs: |
|later | gpio/mux (without ao domain) |
|SoCs | fixup: |
| | pull = gpio; pull-enable = gpio; ds = gpio; |
+------+-----------------------------------------------------------------+
Since m8-axg share the same ao fixup, make a common function
meson8_aobus_parse_dt_extra to do the job.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/1573819429-6937-2-git-send-email-qianggui.song@amlogic.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some devices do not make use of the CMD0/DAT0/DAT2 direction control
pins of the MMC/SD card 0 interface. In this case we should leave
those pins unconfigured.
A similar case already exists for "mc1_a_1" vs "mc1_a_2"
when the MC1_FBCLK pin is not used.
Add a new "mc0_a_2" pin group which is equal to "mc0_a_1" except
with the MC0_CMDDIR, MC0_DAT0DIR and MC0_DAT2DIR pins removed.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191117205439.239211-1-stephan@gerhold.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIOs are marked as wakeup capable and are routed to another
interrupt controller that is an always-domain and can detect interrupts
even when most of the SoC is powered off. The wakeup interrupt
controller wakes up the GIC and replays the interrupt at the GIC.
Setup the TLMM irqchip in hierarchy with the wakeup interrupt controller
and ensure the wakeup GPIOs are handled correctly.
Co-developed-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-9-git-send-email-ilina@codeaurora.org
----
Changes in v2:
- Address review comments
- Fix Co-developed-by tag
Changes in v1:
- Address minor review comments
- Remove redundant call to set irq handler
- Move irq_domain_qcom_handle_wakeup() to this patch
Changes in RFC v2:
- Rebase on top of GPIO hierarchy support in linux-next
- Set the chained irq handler for summary line
* Intel Tigerlake pin controller support has been added.
* Miscellaneous fixes to the main and Cherryview drivers.
* Refactoring of the context restoring in the main driver.
The following is an automated git shortlog grouped by driver:
cherryview:
- Missed type change to unsigned int
- Allocate IRQ chip dynamic
- Fix spelling mistake in the comment
- Fix irq_valid_mask calculation
intel:
- Missed type change to unsigned int
- Add Intel Tiger Lake pin controller support
- Use helper to restore register values on ->resume()
- Drop level from warning to debug in intel_restore_hostown()
- Introduce intel_restore_intmask() helper
- Introduce intel_restore_hostown() helper
- Introduce intel_restore_padcfg() helper
- Avoid potential glitches if pin is in GPIO mode
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEqaflIX74DDDzMJJtb7wzTHR8rCgFAl3MDXMACgkQb7wzTHR8
rCgcURAAkQ/FizpJUX8z6PNdLopJWnRQ9e2d0KEHsyrXxRm/IbgWhnMx176hhLl1
PN9GXpM8t7KX/m5rf/w9EKHldP0SLeFyWxCyzWJ+NtpjahpNbP/enxMfgWJJjbwA
cocmvhXU9oHgiz3VO3DDpUKGkm+yVoYyam1cWlPqLvhDZjHl2okuNfnr6rO59PaB
hGnz8fkIk0xUcSE4wJI63I0UaDwm3YVq9oc8Oq1dtWXaoOX7Eqn1ZELGE15oVPDK
kAlqzF9A8c9bpxuVkLRGq2i3aB9S5Ci9/UoTykViTZfQJ7qz7FCYtV1M29yAvXvn
oOot/5EGw/ZoxVi/ZbjhLA2tcEJM6O3S3iHELPHNaihPOmHycJ0tavgTn89KJBcR
lMR8zS1hpqwIx9KRLEVTGViGdGHLbtu6eXJ+j0qNbezrNcXVdJO0yms2HEbCGe+A
6J8Ucpd4HG5GKHKvnLa7bihvjxdizb/WzjRjE0xbFu2h7j1MKS/3LFcStI5fa0a0
G2pcXgFkr4mui/a8nek/EsATu10KkKt6Aam+xg4DPhUeSoxcC3Jo1EzQ/2Tg/TPI
4XRsEmdiTBHFE2re8mZXkp+g4YYA+KpTMyVsKZC389IJ4cuP8YbsqWJKICoObvuM
CZ7B9wPHN1qXA04E7YaWz2KgmZQCD8mNbsxHiAyAX99nvtyDxjE=
=iLY+
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.5-1
* Intel Tigerlake pin controller support has been added.
* Miscellaneous fixes to the main and Cherryview drivers.
* Refactoring of the context restoring in the main driver.
The following is an automated git shortlog grouped by driver:
cherryview:
- Missed type change to unsigned int
- Allocate IRQ chip dynamic
- Fix spelling mistake in the comment
- Fix irq_valid_mask calculation
intel:
- Missed type change to unsigned int
- Add Intel Tiger Lake pin controller support
- Use helper to restore register values on ->resume()
- Drop level from warning to debug in intel_restore_hostown()
- Introduce intel_restore_intmask() helper
- Introduce intel_restore_hostown() helper
- Introduce intel_restore_padcfg() helper
- Avoid potential glitches if pin is in GPIO mode
We converted 'unsigned' type to be 'unsigned int' in the driver,
but there are couple of leftovers. So, finish the task now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We converted 'unsigned' type to be 'unsigned int' in the driver,
but there are couple of leftovers. So, finish the task now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
With stmfx_pinctrl_gpio_init_valid_mask callback, gpio_valid_mask was used
to initialize gpiochip valid_mask for gpiolib. But gpio_valid_mask was not
yet initialized. gpio_valid_mask required gpio-ranges to be registered,
this is the case after gpiochip_add_data call. But init_valid_mask
callback is also called under gpiochip_add_data. gpio_valid_mask
initialization cannot be moved before gpiochip_add_data because
gpio-ranges are not registered.
So, it is not possible to use init_valid_mask callback.
To avoid this issue, get rid of valid_mask and rely on ranges.
Fixes: da9b142ab2 ("pinctrl: stmfx: Use the callback to populate valid_mask")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191104100908.10880-1-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PM8950 features 8 GPIOs with hole in 3 and PMI8950 has
only two; these PMICs are totally compatible with this driver.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20191031103507.30678-2-kholk11@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The get_direction api is strongly recommended to be implemented. In fact
if it is not implemented gpio-hogs will not get the correct direction.
Add an implementation of get_direction for the nsp-gpio driver.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20191104001819.2300-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use more of the gpiolib infrastructure for handling interrupts. The
root interrupt still needs to be handled manually as it is shared with
other peripherals on the SoC.
This will allow multiple instances of this driver to be supported and
will clean up gracefully on failure thanks to the device managed APIs.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20191104001819.2300-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SDC_QDSD_PINGROUP/UFS_RESET macros are missing the .tile info needed to
calculate the right register offsets. Adding them here and also
adjusting the offsets accordingly.
Fixes: f2ae04c45b ("pinctrl: qcom: Add SC7180 pinctrl driver")
Reported-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/20191021141507.24066-1-rnayak@codeaurora.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On SAM9X60, slewrate should be enabled on pins with a switching frequency
below 50Mhz. Since most of our pins do not exceed this value, we enable
slewrate by default. Pins with a switching value that exceeds 50Mhz will
have to explicitly disable slewrate.
This patch changes the ABI. However, the slewrate macros are only used
by SAM9X60 and, at this moment, there are no device-tree files available
for this platform.
Suggested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20191101092031.24896-1-codrin.ciubotariu@microchip.com
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add support for the new R-Car M3-W+ (r8a77961) SoC,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXbxIwAAKCRCKwlD9ZEnx
cD0JAP9Zk4yPHStUiiwPKwx+ZCJJ2wAAyKLXhSBKLh06h2CKOQEApFYk4xfPAe+f
wsM8M04QtlsYp1ZgX2wpbXiZeBdM+gg=
=OJxF
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v5.5-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.5 (take two)
- Add support for the new R-Car M3-W+ (r8a77961) SoC,
- Small fixes and cleanups.
The definitions for bit field [19:18] of the Peripheral Function Select
Register 3 were accidentally copied from bit field [20], leading to
duplicates for the TCLK1_B function, and missing TCLK0, CAN_CLK_B, and
ET0_ETXD4 functions.
Fix this by adding the missing GPIO_FN_CAN_CLK_B and GPIO_FN_ET0_ETXD4
enum values, and correcting the functions.
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191024131308.16659-1-geert+renesas@glider.be
Add support for the Pin Function Controller in the R-Car M3-W+
(R8A77961) SoC.
R-Car M3-W+ is pin compatible with R-Car M3-W (R8A77960), which allows
for both SoCs to share a driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023122955.12420-4-geert+renesas@glider.be
Rename CONFIG_PINCTRL_PFC_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_PINCTRL_PFC_R8A77960, to avoid confusion with R-Car M3-W+
(R8A77961), which will use CONFIG_PINCTRL_PFC_R8A77961.
Extend the dependency of CONFIG_PINCTRL_PFC_R8A77960 from
CONFIG_ARCH_R8A7796 to CONFIG_ARCH_R8A77960, to relax dependencies for a
future rename of the SoC configuration symbol.
Rename r8a7796_pinmux_info to r8a77960_pinmux_info, as it contains an
r8a77960-based name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023122955.12420-3-geert+renesas@glider.be
As platform_get_irq() now prints an error when the interrupt does not
exist, counting interrupts by looping until failure causes the printing
of scary messages like:
sh-pfc e6060000.pin-controller: IRQ index 0 not found
Fix this by using the platform_irq_count() helper instead.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191016142601.28255-1-geert+renesas@glider.be
This driver adds pinctrl/GPIO support for Intel Tiger Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We can restore only values that had been changed and do not spam kernel log
with unnecessary messages. Convert intel_gpio_update_pad_mode() to a helper
function that will be used across few callers.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we didn't get any new reports from users about wrong settings
of pad ownership, there is no point to spam kernel log with it. Thus,
drop level from warning to debug.
Also, modify format to be in align with the rest restore helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Refactor restoring GPI_IE registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Refactor restoring HOSTSW_OWN registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Deduplicate restoring PADCFGx registers by using a common helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
This patch is heavily based on the attachment to the bug by Christoph Marz.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202543
Fixes: 6e08d6bbeb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Depends-on: 83b9dc1131 ("pinctrl: cherryview: Associate IRQ descriptors to irqdomain")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
One spelling mistake is being fixed: benerate -> generate.
It is a complimentary fix to the commit 505485a83c ("pinctrl:
cherryview fixed typo in comment").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 03c4749dd6 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux
GPIO translation") has made the cherryview gpio numbers sparse, to get
a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux.
This has greatly simplified things, but the code setting the
irq_valid_mask was not updated for this, so the valid mask is still in
the old "compressed" numbering with the gaps in the pin numbers skipped,
which is wrong as irq_valid_mask needs to be expressed in gpio numbers.
This results in the following error on devices using pin 24 (0x0018) on
the north GPIO controller as an ACPI event source:
[ 0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ
This has been reported (by email) to be happening on a Caterpillar CAT T20
tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1.
This commit uses the pin number instead of the compressed index into
community->pins to clear the correct bits in irq_valid_mask for GPIOs
using GPEs for interrupts, fixing these errors and in case of the
Medion Akoya e2215t also fixing the LID switch not working.
Cc: stable@vger.kernel.org
Fixes: 03c4749dd6 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.
However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.
Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf01 ("pinctrl: intel: Initialize GPIO properly when used through irqchip")
Cc: stable@vger.kernel.org
Cc: fei.yang@intel.com
Reported-by: Oliver Barta <oliver.barta@aptiv.com>
Reported-by: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
A couple more fixes for Intel pinctrl drivers:
- Try to avoid glitches when pin is in GPIO mode
- Fix cherryview irq_valid_mask calculation
- Allocate cherryview IRQ chip dynamically to avoid triggering warning
from GPIO core
-----BEGIN PGP SIGNATURE-----
iQJUBAABCgA+FiEEVTdhRGBbNzLrSUBaAP2fSd+ZWKAFAl24fLkgHG1pa2Eud2Vz
dGVyYmVyZ0BsaW51eC5pbnRlbC5jb20ACgkQAP2fSd+ZWKD0QxAAjyg4YGZ9kZD4
MztOOG/l8T+qPRvqg0vWg5yQCP8zcRA15kZ9ybMGHIl4nBPQ2sjfEd5Eu1iArUYt
ieM/T4VJrnCAGJdwj522vLhEfAuaiymq8cAv1DcAk0bVTr/UF32KF5Pq9ZGAReHC
MlkOXMOmihBZ7Oyc9ZMSP+yN122+TvLHmMREbigzyukwtCSNpIUjdu9g+qDRlM/e
agxrN9sGPdLt/xQmPHrJwZ66Y1lHl4LkQIxRadr/3oLyg0u6fCkfB3IdXrL2qM+E
QycJ1NjEgFQMJEJZGxL9jPVS4vzmH9B4oFAS8mAaqUyOi9LvTANKm/mdkYjtdfjC
9e4H+ReneSdtglH2m5fQ3I6zehuBGVbKHfdcLupYWLOyQ4uOepx8F8JgYDLXOSlS
1u0DGmxT4TS6+rbKlo05QVLS1xqRbkSgBUmxNTc84zEgnRDyyz4GFGM3ANWksX0a
cATYOK2XViPGGFv733IRdy4rGGkYpV7T8nq/N0Pj12e+cPo27OiE93ouHrgi6Ovb
4OEbZPSTMwBQ46lZ9io3IEkMwSeN9AbO0u4+9zbN3sKZM89uzMnJeb4IPeUfGLVc
d691Bb1TtSVqtZuXr0Y4d4ou3D3s1AwICHQ3+4dmX2992dJUZyAAJB67fqzb9gbF
VWLyWdKCu/nl+BT5QYU5t7S0BzdpCQs=
=3AVf
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-fixes-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl fixes for v5.4 part 2
A couple more fixes for Intel pinctrl drivers:
- Try to avoid glitches when pin is in GPIO mode
- Fix cherryview irq_valid_mask calculation
- Allocate cherryview IRQ chip dynamically to avoid triggering warning
from GPIO core
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
This patch is heavily based on the attachment to the bug by Christoph Marz.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202543
Fixes: 6e08d6bbeb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Depends-on: 83b9dc1131 ("pinctrl: cherryview: Associate IRQ descriptors to irqdomain")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
- Add support for the new RZ/G2N (r8a774b1) SoC,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXal5/gAKCRCKwlD9ZEnx
cLbfAQCW3HRFA6EGzMOSweSZ+IE1SpaC+K6i8Is9hN+zyXDaYQEA6vskgARnL+SI
NCg42XOKhNNkLYoy7D2dKnkruYbsKA4=
=c90h
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v5.5-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.5
- Add support for the new RZ/G2N (r8a774b1) SoC,
- Small fixes and cleanups.
