Add support for the HW feature of multi-packet WQE in XDP
xmit flow.
The conventional TX descriptor (WQE, Work Queue Element) serves
a single packet. Our HW has support for multi-packet WQE (MPWQE)
in which a single descriptor serves multiple TX packets.
This reduces both the PCI overhead and the CPU cycles wasted on
writing them.
In this patch we add support for the HW feature, which is supported
starting from ConnectX-5.
Performance:
Tested packet rate for UDP 64Byte multi-stream over ConnectX-5 NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
XDP_TX:
We see a huge gain on single port ConnectX-5, and reach the 100 Mpps
milestone.
* Single-port HCA:
Before: 70 Mpps
After: 100 Mpps (+42.8%)
* Dual-port HCA:
Before: 51.7 Mpps
After: 57.3 Mpps (+10.8%)
* In both cases we tested traffic on one port and for now On Dual-port HCAs
we see only small gain, we are working to overcome this bottleneck, but
for the moment only with experimental firmware on dual port HCAs we can
reach the wanted numbers as seen on Single-port HCAs.
XDP_REDIRECT:
Redirect from (A) ConnectX-5 to (B) ConnectX-5.
Due to a setup limitation, (A) and (B) are on different NUMA nodes,
so absolute performance numbers are not optimal.
Note:
Below is the transmit rate of (B), not the redirect rate of (A)
which is in some cases higher.
* (B) is single-port:
Before: 77 Mpps
After: 90 Mpps (+16.8%)
* (B) is dual-port:
Before: 61 Mpps
After: 72 Mpps (+18%)
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of SR-IOV LAG, checking whether LAG is active
is no longer good enough, since RoCE and SR-IOV LAG each entails
different behavior by both the core and infiniband drivers.
This patch introduces facilities to discern LAG type, in addition to
mlx5_lag_is_active(). These are implemented in such a way as to allow
more complex mode combinations in the future.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This introduces devcom, a generic mechanism for performing operations
on both physical functions of the same Connect-X card.
The first user of this API is merged eswitch, which will be introduced
in subsequent patches.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5-next shared branch with rdma subtree to avoid mlx5 rdma v.s. netdev
conflicts.
Highlights:
1) Lag refactroing and flow counter affinity bits.
2) mlx5 core cleanups
By Roi Dayan (2) and others
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Fold the modify lag code into function
net/mlx5: Add lag affinity info to log
net/mlx5: Split the activate lag function into two routines
net/mlx5: E-Switch, Introduce flow counter affinity
IB/mlx5: Unify e-switch representors load approach between uplink and VFs
net/mlx5: Use lowercase 'X' for hex values
net/mlx5: Remove duplicated include from eswitch.c
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This dictates the device affinity for eswitch flow counters, set by the FW
according to the HW device capabilities.
Under "source eswitch" affinity, the counter should be allocated on the
device related to the source vport in the match. This covers both non
merged e-switch mode as well as old FW that does not advertise this cap.
Under "flow eswitch" affinity, the counter should be allocated on the
device where the eswitch rule is set.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Apparently gcc is cool with upper case '0X' but it is not commonly used.
Replace '0X' with lowercase '0x' in mlx5_ifc.h file.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cap bits locations for the fdb caps of multi path to table (used for
local mirroring) and multi encap (used for prio/chains) were wrongly used
in swapped locations. This went unnoted so far b/c we tested the offending
patch with CX5 FW that supports both of them. On different environments where
not both caps are supported, we will be messed up, fix that.
Fixes: b9aa0ba17a ('net/mlx5: Add cap bits for multi fdb encap')
Signed-off-by: Vu Pham <vu@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Tested-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
PPCNT is not supported if PCAM access reg is supported and ppcnt bit is clear.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Writing 64B CQEs to 128B cache lines results in a RMW operation. Padding
the CQEs to 128B if possible improves performance on 128B cache line
systems like PPC.
Testing on PPC showed up to a 24% improvement in small packet throughput
vs the default behavior, depending on the workload and system topology.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This isn't used anywhere across the mlx5 driver stack,
remove it.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Update the flow steering command formatting according to the extended
destination API.
Note that the FW dictates that multi destination FTEs that involve at
least one encap must use the extended destination format, while single
destination ones must use the legacy format.
Using extended destination format requires FW support. Check for its
capabilities and return error if not supported.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change the driver flow destination struct to use bit flags with the vhca
id valid being the 1st one. The flags field is more extendable and will
be used in downstream patch.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Extended destinations provide the ability to configure different
encapsulation properties per destination on a single FTE. This is
needed for use-cases such as remote mirroring over tunneled networks.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
GRE RFC defines a 32 bit key field. NVGRE RFC splits the 32 bit
key field to 24 bit VSID (gre_key_h) and 8 bit flow entropy (gre_key_l).
Define the two key parsing alternatives in a union, thus enabling both
access methods.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Will be used in downstream patch to monitor counter changes
by the HCA and report it to the driver by an event.
The driver will update its counters cached data accordingly.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce and use a helper that extracts the opcode
from a CQE (completion queue entry) structure.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Packet based credit mode bit determines whether the credit mode
is done per message or packet. Expose the QP creation flag and
the HCA capability.
Signed-off-by: Danit Goldberg <danitg@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Expose device capabilities for DEVX user context, it includes which caps
the device is supported and a matching bit to set as part of user
context creation.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Transfer initialization and cleanup from mlx5_priv struct of
mlx5_core_dev to be part of mlx5_ib_dev. This completes removal
of SRQ from mlx5_core.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
There is no need to keep SRQ which is RDMA object in mlx5_core.
In this patch, we partially move the execution code, while next patches
will move table initialization/release logic too.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Delete functions which are not called and not needed.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Ensure that both RDMA and netdev parts of SRQ implementation
has same copyright and license information annotated by SPDX
tags.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Allow forwarding of SRQ events to mlx5_core interfaces, e.g. mlx5_ib.
Use mlx5_notifier_register/unregister in srq.c in order to allow seamless
transition of srq.c to infiniband subsystem.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Allow forwarding QP and WQ events to mlx5_core interfaces, e.g. mlx5_ib
Use mlx5_notifier_register/unregister in qp.c in order to allow seamless
transition of qp.c to infiniband subsystem.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Before the new mlx5 event notification infrastructure and API,
mlx5_core used to process all events before forwarding them to mlx5
interfaces (mlx5e/mlx5_ib) and used to translate the event type enum
to a software defined enum, this is not needed anymore since it is ok
for mlx5e and mlx5_ib to receive FW events as is, at least the few ones
mlx5 core allows.
mlx5e and mlx5_ib already moved to use the new API and they only handle FW
events types, it is now safe to remove all equivalent software defined
events and the logic around them.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The mlx5_interface->event callback is not used by mlx5e/mlx5_ib anymore.
We totally remove the delayed events logic work around, since with
the dynamic notifier registration API it is not needed anymore, mlx5_ib
can register its notifier and start receiving events exactly at the moment
it is ready to handle them.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This to allow seamless migration to the new notifier chain API, and to
eventually deprecate interfaces dev->event callback.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use atomic notifier chain to fire events to mlx5 core driver
consumers (mlx5e/mlx5_ib) and provide mlx5 register/unregister notifier
API.
This API will replace the current mlx5_interface->event callback and all
the logic around it, especially the delayed events logic introduced by
commit 97834eba7c ("net/mlx5: Delay events till ib registration ends")
Which is not needed anymore with this new API where the mlx5 interface
can dynamically register/unregister its notifier.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move all the generic async events handling into new specific events
handling file events.c to keep eq.c file clean from concrete event logic
handling.
Use new API to register for NOTIFY_ANY to handle generic events and
dispatch allowed events to mlx5_core consumers (mlx5_ib and mlx5e)
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to QP/SRQ resources events handlers on several FW
events and let resources logic register resources events notifiers via the
new API.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to mlx5_cmd_comp_handler on MLX5_EVENT_TYPE_CMD
and let command interface to register its own handler when its ready.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to mlx5_core_req_pages_handler on
MLX5_EVENT_TYPE_PAGE_REQUEST and let FW page logic to register its own
handler when its ready.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove the explicit call to mlx5_pps_event on MLX5_EVENT_TYPE_PPS_EVENT
and let clock logic to register its own handler when its ready.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use atomic_notifier_chain to fire firmware events at internal mlx5 core
components such as eswitch/fpga/clock/FW tracer/etc.., this is to
avoid explicit calls from low level mlx5_core to upper components and to
simplify the mlx5_core API for future developments.
Simply provide register/unregister notifiers API and call the notifier
chain on firmware async events.
Example: to subscribe to a FW event:
struct mlx5_nb port_event;
MLX5_NB_INIT(&port_event, port_event_handler, PORT_CHANGE);
mlx5_eq_notifier_register(mdev, &port_event);
where:
- port_event_handler is the notifier block callback.
- PORT_EVENT is the suffix of MLX5_EVENT_TYPE_PORT_CHANGE.
The above will guarantee that port_event_handler will receive all FW
events of the type MLX5_EVENT_TYPE_PORT_CHANGE.
To receive all FW/HW events one can subscribe to
MLX5_EVENT_TYPE_NOTIFY_ANY.
The next few patches will start moving all mlx5 core components to use
this new API and cleanup mlx5_eq_async_int misx handler from component
explicit calls and specific logic.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use the new generic EQ API to move all ODP RDMA data structures and logic
form mlx5 core driver into mlx5_ib driver.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Add mlx5_eq_{create/destroy}_generic APIs and EQE access methods, for
mlx5 core consumers generic EQs.
This API will be used in downstream patch to move page fault (RDMA ODP)
EQ logic into mlx5_ib rdma driver, hence it will use a generic EQ.
Current mlx5 EQ allocation scheme:
On load mlx5 allocates 4 (for async) + #cores (for data completions)
MSIX vectors, mlx5 core will assign 3 MSIX vectors for internal async
EQs and will use all of the #cores MSIX vectors for completion EQs,
(One vector is going to be reserved for a generic EQ).
After this patch an external user (e.g mlx5_ib) of mlx5_core
can use this new API to create new generic EQs with the reserved msix
vector index for that eq.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
In mlx5 we have three types of usages for EQs,
1. Asynchronous EQs, used internally by mlx5 core for
a. FW command completions
b. FW page requests
c. one EQ for all other Asynchronous events
2. Completion EQs, used for CQ completion (we create one per core)
3. *Special type of EQ (page fault) used for RDMA on demand paging
(ODP).
*The 3rd type shouldn't be special at least in mlx5 core, it is yet
another async events EQ with specific use case, it will be removed in
the next two patches, and will completely move its logic to mlx5_ib,
as it is rdma specific.
In this patch we remove use case (eq type) specific fields from
struct mlx5_eq into a new eq type specific structures.
struct mlx5_eq_async;
truct mlx5_eq_comp;
struct mlx5_eq_pagefault;
Separate between their type specific flows.
In the future we will allow users to create there own generic EQs.
for now we will allow only one for ODP in next patches.
We will introduce event listeners registration API for those who
want to receive mlx5 async events.
After that mlx5 eq handling will be clean from feature/user specific
handling.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Move unnecessary EQ table structures and declaration from the
public include/linux/mlx5/driver.h into the private area of mlx5_core
and into eq.c/eq.h.
Introduce new mlx5 EQ APIs:
mlx5_comp_vectors_count(dev);
mlx5_comp_irq_get_affinity_mask(dev, vector);
And use them from mlx5_ib or mlx5e netdevice instead of direct access to
mlx5_core internal structures.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
irq_info and rmap are EQ properties of the driver, and only needed for
EQ objects, move them to the eq_table EQs database structure.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Completion EQs list is only modified on driver load/unload, locking is
not required, remove it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
eq->index is used only for completion EQs and is assigned to be
the completion eq index, it is used only when traversing the completion
eqs list, and it can be calculated dynamically, thus remove the
eq->index field.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Some fields and structures are not referenced nor used by the driver,
remove them.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Currently the cpu affinity hint mask for completion EQs is stored and
read from the wrong place, since reading and storing is done from the
same index, there is no actual issue with that, but internal irq_info
for completion EQs stars at MLX5_EQ_VEC_COMP_BASE offset in irq_info
array, this patch changes the code to use the correct offset to store
and read the IRQ affinity hint.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Sometimes upper layers may want to prevent the destruction of a core
resource for a period of time while work on that resource is in
progress. Add API to support this.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Fix wrong offsets of reserved fields in ifc file.
Issues found using pahole.
Signed-off-by: Gal Pressman <pressmangal@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adapt XRC SRQ to the latest HW specification with fixed definition
around umem valid bits. The previous definition relied on a bit which
was taken for other purposes in legacy FW.
Fixes: bd37197554 ("net/mlx5: Update mlx5_ifc with DEVX UID bits")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
This has been a smaller cycle with many of the commits being smallish code
fixes and improvements across the drivers.
- Driver updates for bnxt_re, cxgb4, hfi1, hns, mlx5, nes, qedr, and rxe
- Memory window support in hns
- mlx5 user API 'flow mutate/steering' allows accessing the full packet
mangling and matching machinery from user space
- Support inter-working with verbs API calls in the 'devx' mlx5 user API, and
provide options to use devx with less privilege
- Modernize the use of syfs and the device interface to use attribute groups
and cdev properly for uverbs, and clean up some of the core code's device list
management
- More progress on net namespaces for RDMA devices
- Consolidate driver BAR mmapping support into core code helpers and rework
how RDMA holds poitners to mm_struct for get_user_pages cases
- First pass to use 'dev_name' instead of ib_device->name
- Device renaming for RDMA devices
-----BEGIN PGP SIGNATURE-----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=pacJ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a smaller cycle with many of the commits being smallish
code fixes and improvements across the drivers.
- Driver updates for bnxt_re, cxgb4, hfi1, hns, mlx5, nes, qedr, and
rxe
- Memory window support in hns
- mlx5 user API 'flow mutate/steering' allows accessing the full
packet mangling and matching machinery from user space
- Support inter-working with verbs API calls in the 'devx' mlx5 user
API, and provide options to use devx with less privilege
- Modernize the use of syfs and the device interface to use attribute
groups and cdev properly for uverbs, and clean up some of the core
code's device list management
- More progress on net namespaces for RDMA devices
- Consolidate driver BAR mmapping support into core code helpers and
rework how RDMA holds poitners to mm_struct for get_user_pages
cases
- First pass to use 'dev_name' instead of ib_device->name
- Device renaming for RDMA devices"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (242 commits)
IB/mlx5: Add support for extended atomic operations
RDMA/core: Fix comment for hw stats init for port == 0
RDMA/core: Refactor ib_register_device() function
RDMA/core: Fix unwinding flow in case of error to register device
ib_srp: Remove WARN_ON in srp_terminate_io()
IB/mlx5: Allow scatter to CQE without global signaled WRs
IB/mlx5: Verify that driver supports user flags
IB/mlx5: Support scatter to CQE for DC transport type
RDMA/drivers: Use core provided API for registering device attributes
RDMA/core: Allow existing drivers to set one sysfs group per device
IB/rxe: Remove unnecessary enum values
RDMA/umad: Use kernel API to allocate umad indexes
RDMA/uverbs: Use kernel API to allocate uverbs indexes
RDMA/core: Increase total number of RDMA ports across all devices
IB/mlx4: Add port and TID to MAD debug print
IB/mlx4: Enable debug print of SMPs
RDMA/core: Rename ports_parent to ports_kobj
RDMA/core: Do not expose unsupported counters
IB/mlx4: Refer to the device kobject instead of ports_parent
RDMA/nldev: Allow IB device rename through RDMA netlink
...
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
