lockdep spots that the fb_info->lock takes the dev->struct_mutex during
init (due to the device probing) and so we can not hold
dev->struct_mutex when unregistering the framebuffer. Simply reverse the
order of initialisation during cleanup and so do the intel_fbdev_fini()
before the intel_modeset_cleanup.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The display port DPMS state is tracked internally in the display port
driver so that when a hotplug event comes along, the driver can know
whether to try retraining the link. This doesn't work well if the
driver never sets the DPMS state to ON when the output is enabled.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cancel the output polling work proc before acquiring the struct mutex
to avoid acquiring the work proc mutex with the struct mutex
held. This avoids inverting the lock order seen when the work proc
runs.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Move the access control up from the fast paths, which are no longer
universally taken first, up into the caller. This then duplicates some
sanity checking along the slow paths, but is much simpler.
Tracked as CVE-2010-2962.
Reported-by: Kees Cook <kees@ubuntu.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Instead of waiting for the display line value to settle, we can simply
wait for the pipe configuration register 'state' bit to turn off.
Contrarywise, disabling the plane will not cause the display line
value to stop changing, so instead we wait for the vblank interrupt
bit to get set. And, we only do this when we're not about to wait for
the pipe to turn off.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
While the display port is in training mode, vblank interrupts don't
occur. Because we have to wait for the display port output to turn on
before starting the training sequence, enable the output in 'normal'
mode so that we can tell when a vblank has occurred, then start the
training sequence.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Extend the error handling code with operations found in other nearby error
handling code
A simplified version of the sematic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
@r@
statement S1,S2,S3;
constant C1,C2,C3;
@@
*if (...)
{... S1 return -C1;}
...
*if (...)
{... when != S1
return -C2;}
...
*if (...)
{... S1 return -C3;}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The return from move_to_gtt_domain() may indicate a pending signal which
needs to handled as opposed to an actual error, for instance, so report
the original return value rather than forcing an EINVAL.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
vmwgfx: Fix fb VRAM pinning failure due to fragmentation
vmwgfx: Remove initialisation of dev::devname
vmwgfx: Enable use of the vblank system
vmwgfx: vt-switch (master drop) fixes
drm/vmwgfx: Fix breakage introduced by commit "drm: block userspace under allocating buffer and having drivers overwrite it (v2)"
drm: Hold the mutex when dropping the last GEM reference (v2)
drm/gem: handlecount isn't really a kref so don't make it one.
drm: i810/i830: fix locked ioctl variant
drm/radeon/kms: add quirk for MSI K9A2GM motherboard
drm/radeon/kms: fix potential segfault in r600_ioctl_wait_idle
drm: Prune GEM vma entries
drm/radeon/kms: fix up encoder info messages for DFP6
drm/radeon: fix PCI ID 5657 to be an RV410
The issue is that we may become stuck executing a long running shader
and continually attempt to reset the GPU. (Or maybe we tickle some bug
and need to break the vicious cycle.) So if we are detect a second hang
within 5 seconds, give up trying to programme the GPU and report it
wedged.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
So far only found registers for i830, i845, i865 and one of those has no
effect on i865!
At this moment in time, attempting to reset i8xx is a little
optimistic...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When the GPU is reset, the fence registers are invalidated, so release
the objects and clear them out.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Only drm/i915 does the bookkeeping that makes the information useful,
and the information maintained is driver specific, so move it out of the
core and into its single user.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
If the soon-to-be scanout buffer is partly covering the intended
VRAM region, move and pin will fail. In that case, just move it out
to system before attempting to move it in again.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The removed code causes oopses with newer drms on master drop.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is to avoid accessing uninitialized data during
drm_irq_uninstall and vblank ioctls. At the same time, enable error check from
drm_kms_init which previously appeared to ignore all errors.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We add an option not to enable fbdev, this option is off (0) by default.
Not enabling fbdev at load time makes it possible to co-operate with
vga16fb and vga text mode when VT switching.
However, if 3D resources are active when VT switching, we're currently
not able to switch over to vga, due to device limitations.
This fixes a bug where we previously lost 3D state during VT switch.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The mentioned commit breaks the vmwgfx ioctl argument sanity check.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In order to be fully threadsafe we need to check that the drm_gem_object
refcount is still 0 after acquiring the mutex in order to call the free
function. Otherwise, we may encounter scenarios like:
Thread A: Thread B:
drm_gem_close
unreference_unlocked
kref_put mutex_lock
... i915_gem_evict
... kref_get -> BUG
... i915_gem_unbind
... kref_put
... i915_gem_object_free
... mutex_unlock
mutex_lock
i915_gem_object_free -> BUG
i915_gem_object_unbind
kfree
mutex_unlock
Note that no driver is currently using the free_unlocked vfunc and it is
scheduled for removal, hasten that process.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30454
Reported-and-Tested-by: Magnus Kessler <Magnus.Kessler@gmx.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that we hold onto a reference whilst evicting objects, we need to
be sure that we drop all the references taken -- even on the error
paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There were lots of places being inconsistent since handle count
looked like a kref but it really wasn't.
Fix this my just making handle count an atomic on the object,
and have it increase the normal object kref.
Now i915/radeon/nouveau drivers can drop the normal reference on
userspace object creation, and have the handle hold it.
This patch fixes a memory leak or corruption on unload, because
the driver had no way of knowing if a handle had been actually
added for this object, and the fbcon object needed to know this
to clean itself up properly.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Added a function that sets the LVDS values to default settings. This
will be called by intel_init_bios before checking for the VBT (video BIOS
table). The default values are thus loaded regardless of whether a VBT
is found.
The default settings in each parse function have been moved to the new
function. This consolidates all the default settings into one place.
The default dither bit value has been changed from 0 to 1. We can
assume that display devices will want dithering enabled.
Signed-off-by: Simon Que <sque@chromium.org>
Acked-by: Olof Johansson <olof@lixom.net>
[ickle: fixup for -next]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
At that point as the object is no longer in any GPU write domain it must
not be on the list, so the list_del() is redundant.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The i810 and i830 device drivers may replace their file operations
on an open file descriptor. My previous patch to move the BKL
out of the common DRM code into these drivers only caught the
default file operations, not the ones that actually end up being
used.
Found while trying to come up with a way to kill the BKL for
good in these drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just reschedule the retire requests again if the device is currently
busy. The request list will be pruned along other paths so will never
grow unbounded and so we can afford to miss the occasional pruning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This check only appears to succeed when using GMBUS, so we need to skip
it if we have fallen back to using GPIO bit banging.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There are several reported instances of GMBUS failing to successfully
read the EDID, so revert back to bit banging until the issue is
resolved.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30371
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Besides a couple of bugs when writing more than a single byte along the
GMBUS, SDVO was completely failing whilst trying to use GMBUS, so use
bit banging instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With multiple rings generating requests independently, the outstanding
requests must also be track independently.
Reported-by: Wang Jinjin <jinjin.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30380
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Board has no digital connectors
Reported-by: Andy Walls <awalls@md.metrocast.net>
Tested-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Hook the GEM vm open/close ops into the generic drm vm open/close so
that the private vma entries are created and destroy appropriately.
Fixes the leak of the drm_vma_entries during the lifetime of the filp.
Reported-by: Matt Mackall <mpm@selenic.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The IPS driver needs to know the current power consumption of the GMCH
in order to make decisions about when to increase or decrease the CPU
and/or GPU power envelope. So fix up the divisions to save the results
so the numbers are actually correct (contrary to some earlier comments
and code, these functions do not modify the first argument and use it
for the result).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
encoder info was not printed properly on boards using the
DFP6 id.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Introduced by 48b956c5, I had thought I had already fixed this. Oh well.
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Daniel Vetter pointed out that in this case is would be clearer and
cleaner to use a spinlock instead of a mutex to protect the per-file
request list manipulation. Make it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
I've accidently killed a little bit too much in
commit 1da3f87ebb
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Aug 23 22:53:24 2010 +0200
drm: kill kernel_context_switch callbacks
Note to self: Next time also test with AIGLX disabled.
Reported-and-Tested-by: Andy Furniss <lists@andyfurniss.entadsl.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30374
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's the same code, essentially, so kill all copies safe one unified
version.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
All functions are extremely similar, so fold them into one generic
implementation.
This function isn't used anyway, because there's not yet a bsd ring
error state dumper.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Two macros that use a base address for HWS_PGA were missing, add them.
Also switch the remaining users of *_ACTHD to the ring-base one.
Kill the other ring-specific macros because they're now unused.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[ickle: And silence checkpatch whilst in the vicinity]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This was mixed up in the following patch:
commit a6c45cf013
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Sep 17 00:32:17 2010 +0100
drm/i915: INTEL_INFO->gen supercedes i8xx, i9xx, i965g
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Everything is now handled in intel-gtt.h so these defines
are only confusing.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Owain Ainsworth reported an issue between the interaction of the
hangcheck and userspace immediately (and permanently) falling back to
s/w rasterisation. In order to break the mutex and begin resetting the
GPU, we must abort the current operation (usually within the wait) and
climb sufficiently far back up the call chain to drop the mutex. In his
implementation, Owain has a loop within the ioctl handler to detect the
hang and then sleep until the error handler has run. I've chosen to
return to userspace and report an EAGAIN which should trigger the
userspace ioctl handler to repeat the call (simply because it felt less
invasive...). Before hitting a wedged GPU, we then wait upon completion
of the error handler.
Reported-by: Owain G. Ainsworth <zerooa@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Avoid cause latencies in other clients by not taking the global struct
mutex and moving the per-client request manipulation a local per-client
mutex. For example, this allows a compositor to schedule a page-flip
(through X) whilst an OpenGL application is monopolising the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch fixes the black screen bug on Dell e6510, by
adding two delays to give the eDP panel time to turn on before we
continue with the next write.
300ms is rather arbitray and a rather long sleep, we need to find a way
of refining this value.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29278
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
First step, lets have a look at the values for troublesome panels and
see if they may be used to improve our link training.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to drain the pending flips prior to disabling the pipe during
modeset, and these need to be done in an uninterruptible fashion.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we presume space is signed when computing and looking for wrap along,
make it so.
Reported-by: Owain G. Ainsworth <zerooa@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Just in case someone, somewhere, does something difficult. This also
removes one path that was different between fermi and non-fermi.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Francesco Marella <fmarl@paranoici.org>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_bios_fp_mode() zeroes the mode struct before filling in relevant
entries. This nukes the mode id initialised by drm_mode_create(), and
causes warnings from idr when we try to remove the mode.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Used on nv17-nv28, they contain memory clocks and timings, only one of
the table entries can actually be used, depending on the RAMCFG
straps, and it's usually higher than the frequency programmed on boot
by the BIOS.
The memory timings listed in table version 0x1x are used to init the
0x12xx range but they aren't required for reclocking to work.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Build breakage:
drivers/built-in.o: In function `nouveau_acpi_edid':
(.text+0x13404e): undefined reference to `acpi_video_get_edid'
make: *** [.tmp_vmlinux1] Error 1
Introduced by:
a6ed76d7ff is the first bad commit
commit a6ed76d7ff
Author: Ben Skeggs <bskeggs@redhat.com>
Date: Mon Jul 12 15:33:07 2010 +1000
drm/nouveau: support fetching LVDS EDID from ACPI
Based on a patch from Matthew Garrett.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
It doesn't seem to revert cleanly, but the problem lies in these
two config entries:
CONFIG_ACPI=y
CONFIG_ACPI_VIDEO=m
Adding a select for ACPI_VIDEO appears to be the best solution, and
is comparable to what is done in DRM_I915. Builds, boots, and appears to
work correctly.
Signed-off-by: Philip J. Turmel <philip@turmel.org>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Currently just hooked up to the already-existing nouveau_hw, which should
handle all relevant chipsets as well as we currently can.
This will likely be eventually split out and improved into chipset specific
code at a later point.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will make nouveau_pm attempt to report the card's current performance
level both during bootup, and through sysfs.
This is a very initial implementation, and can be improved a *lot*
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This replaces all the pll_types definitions for ones that match the types
used in the tables in recent VBIOS versions.
get_pll_limits() will now accept either type or register value as input
across all limits table versions, and will store the actual register ID
that a PLL type refers to in the returned structure.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The rest of the connector code assumes we can kfree() the EDID pointer.
This causes things to blow up with the ACPI EDID pointer we get
passed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The most important part of this change is that we now instruct PFIFO to
drop all pending fetches, rather than attempting to skip a single dword
and hope that things would magically sort themselves out - they usually
don't, and we end up with PFIFO being completely hung.
This commit also adds somewhat more useful logging when these exceptions
occur.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
More Apple brain damage, it fixes the modesetting failure on an eMac
G4 (fdo bug 29810).
Reported-by: Zoltan Varnagy <doi@freemail.hu>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Instead of emptying the caches to avoid a race with the PFIFO puller,
go straight ahead and try to recover from it when it happens. Also,
kill pfifo->cache_flush and tile->lock, we don't need them anymore.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This makes sure that RAMHT is cleared correctly on start up.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
FW seems to be broken on nv18, it causes random lockups and breaks
suspend/resume even with the blob.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This doesn't actually happen now, but there's a test case for an earlier
kernel where a GPU error is signalled on one of nv50's fake channels, and
the ramht lookup by the IRQ handler triggered an oops.
This adds a check for RAMHT's existance on a channel before looking up
an object handle.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Will be used at a later point when we plug in an alternative VRAM memory
manager for GeForce 8+ boards.
Based on pscnv code to do the same.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
They don't seem to do anything useful, and we really want to program
CRE_LCD if we aren't lucky enough to find the right CRTC binding
already set.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On some boards the residual current DAC outputs can draw when they're
disconnected can be high enough to give a false load detection
positive (I've only seen it in the S-video luma output of some cards,
but just to be sure). The output line capacitance is limited and
sampling twice should fix it reliably.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Hopefully this one will be better able to cope with moving tiled buffers
around without getting them all scrambled as a result.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nv2x CRTC FIFOs are as large as in nv3x (4kB it seems), and the FIFO
control registers have the same layout: we can make them share the
same implementation.
Previously we were using the nv1x code, but the calculated FIFO
watermarks are usually too low for nv2x and they cause horrible
scanout artifacts. They've gone unnoticed until now because we've been
leaving one of the bandwidth regs uninitialized (CRE 47, which
contains the most significant bits of FFLWM), so everything seemed to
work fine except in some cases after a cold boot, depending on the
memory bandwidth and pixel clocks used.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On some nv4x cards (specifically, the ones that use an internal
PCIE->AGP bridge) the AGP controller state isn't preserved after a
suspend/resume cycle, and the AGP control registers have moved from
0x18xx to 0x100xx, so the FW check in nouveau_mem_reset_agp() doesn't
quite work. Check "dev->agp->mode" instead.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Correct function being needlessly visible outside compilation unit
when the only users are internal.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix string interpreted as trigraph and typo.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Correct function storage class, and correct assignment type.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Correct allocation flags type and function prototype for ANSI C compliance.
[airlied: whitespace fixed]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
nouveau_bios_fp_mode() zeroes the mode struct before filling in relevant
entries. This nukes the mode id initialised by drm_mode_create(), and
causes warnings from idr when we try to remove the mode.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the event that the external chipset doesn't implement the
GET_SUPPORTED_ENHANCEMENTS commands, gracefully treat it as having no
enhancments rather than bailing.
Reported-and-tested-by: Woody Suwalski <terraluna977@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18342
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We weren't unlinking the freed connector from the drm lists, and so
hit some use-after-free if we failed to initialise the connector.
Reported-and-tested-by: Woody Suwalski <terraluna977@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18342
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to wait for the PLLs to settle prior to detecting the state
changes. The BIOS writers guide suggests waiting for the next vblank.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is already performed with the pipelined flush, so by the time we
schedule the flush in the page-flip, the ring is NULL and we OOPs
instead.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A minor typo caused a single fence register to be incorrectly
programmed, resulting in occassional tiling corruption.
Reported-and-tested-by: Hans de Bruin <bruinjm@xs4all.nl>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18962
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
The BIOS writer's guide suggests that a VGA connection will ACK a write
to address 0xA0 and that this should be used before doing legacy
load-detection. Considering the extreme cost of load-detection,
performing an extra DDC seems a risk worth taking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Previously when converting the GMBUS pin to the GPIO reg, we would
offset the pin by one and then use the look-up table. Now that we first
try to use the GMBUS pin, we no longer need the offset and can use the
value from the VBIOS directly.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It makes sense for a BO to move after a process has requested
exclusive RW access on it (e.g. because the BO used to be located in
unmappable VRAM and we intercepted the CPU access from the fault
handler).
If we let the ghost object inherit cpu_writers from the original
object, ttm_bo_release_list() will raise a kernel BUG when the ghost
object is destroyed. This can be reproduced with the nouveau driver on
nv5x.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
As we do not wait for the panel to turn off when we need to adjust the
panel-fitting registers we also need to unlock the PLLs as with the
non-pfit update path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to handle disable_functions() where the framebuffer is
decoupled from the crtc we need to unpin the fb in order to prevent a
leak.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Suspending (especially hibernating) may take a finite amount of time,
during which a hotplug event may trigger and we will attempt to handle
it with inconsistent state. Disable hotplug polling around suspend and
resume.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30070
Reported-by: Rui Tiago Matos <tiagomatos@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Consolidate everything in intel-gtt.c and also kill the export
of intel_max_stolen.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Keep a list of pinned objects and display it via debugfs. Now all
objects that exist in the GTT are always tracked on one of the
active, flushing, inactive or pinned lists.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If we have queued a page flip on the current fb and then request a mode
change, wait until the page flip completes before performing the new
request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Track if the gpu requires the fence for the execution of a batch buffer
and so only wait upon the retirement of the object's last rendering
seqno if the fence is in use by the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Always PAGE_SIZE and only complicates the code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Documentation explicitly mentions that the ring registers are
designed to have the same offsets relative to a base registers.
Use this to fight the code beaurocratic in intel_ringbuffer.c.
No code changes in this patch, just the new definitions.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This looks like a copy-paste remnant from the i810. All the regs
that are actually used are already defined somewhere else in i915_reg.h!
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This ring buffer is used for video decoding/encoding on Sandybridge.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As noted by Zhenyu, we can now simply replace the existing advance hook
by calling the new set_tail function pointer directly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is prepared for video codec ring buffer on Sandybridge. It is
needed to read/write more than one register to move the tail pointer of
the video codec ring on Sandybridge.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Introduce intel_init_render_ring_buffer(), intel_init_bsd_ring_buffer
for ring initialization.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Previously we only tidied up the active bo lists for chipsets were we
would attempt to reset the GPU. However, this action is necessary for
the system to continue and reclaim the dead bo for all chipsets.
Pointed out, in passing, by Owain Ainsworth.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Clear the GPU read domain for the inactive objects on a reset so that
they are correctly invalidated on reuse.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Owain Ainsworth noticed that the reset code failed to clear the flushing
list leaving the driver in an inconsistent state following a hung GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When flushing the GPU domains,we emit a flush on *both* rings, even
though they share a unified cache. Only emit the flush on the currently
active ring.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Change the semantics to retire any buffer older than the current seqno
rather than repeatedly calling calling the function to retire the
buffer at the head of the list matching the request seqno.
Whilst this should have no semantic impact on the implementation, Daniel
was wondering if there was a bug where we might miss a retirement and so
end up with a continually growing active list.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On more recent chipsets, restoring the display is not as simple as
writing a few registers, so force a full modeset of the current
configuration in order to retrain the display link.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Ironlake's graphics reset register has to be accessed via the MCHBAR,
rather than via PCI config space, which requires some refactoring.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The graphics domains are listed as GRDOM in the documentation, and the
GDRST PCI config register (0xc0) is only valid on I965 and GM45. Newer
chips (like Sandy Bridge) have a different GDRST.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Previously, it was only being set if passed GDRST_FULL - but the only
caller passed GDRST_RENDER. So the hardware never actually reset.
The comments also did not match the code.
Instead, just set the reset bit regardless of what flags were passed.
The GPU now resets correctly on my GM45.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We assume that the panel is permenantly connected and that the EDID data
is consistent from boot, so simply cache the whole EDID for the panel.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
During heavy aperture thrashing we may be forced to wait upon several active
objects during eviction. The active list may be the last reference to
these objects and so the action of waiting upon one of them may cause
another to be freed (and itself unbound). To prevent the object
disappearing underneath us, we need to acquire and hold a reference
whilst unbinding.
This should fix the reported page refcount OOPS:
kernel BUG at drivers/gpu/drm/i915/i915_gem.c:1444!
...
RIP: 0010:[<ffffffffa0093026>] [<ffffffffa0093026>] i915_gem_object_put_pages+0x25/0xf5 [i915]
Call Trace:
[<ffffffffa009481d>] i915_gem_object_unbind+0xc5/0x1a7 [i915]
[<ffffffffa0098ab2>] i915_gem_evict_something+0x3bd/0x409 [i915]
[<ffffffffa0027923>] ? drm_gem_object_lookup+0x27/0x57 [drm]
[<ffffffffa0093bc3>] i915_gem_object_bind_to_gtt+0x1d3/0x279 [i915]
[<ffffffffa0095b30>] i915_gem_object_pin+0xa3/0x146 [i915]
[<ffffffffa0027948>] ? drm_gem_object_lookup+0x4c/0x57 [drm]
[<ffffffffa00961bc>] i915_gem_do_execbuffer+0x50d/0xe32 [i915]
Reported-by: Shawn Starr <shawn.starr@rogers.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18902
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.
Based on an original patch by Jesse Barnes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There is a second revision of B43 (a desktop gen4 part) floating around,
functionally equivalent to the original B43, so simply add the new
PCI-IDs.
Bugzilla: https://bugs.freedesktop.org/show_bugs.cgi?id=30221
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
With 5 places to update when adding handling for fence registers, it is
easy to overlook one or two. Correct that oversight, but fence
management should be improved before a new set of registers is added.
Bugzilla: https://bugs.freedesktop.org/show_bug?id=30199
Original patch by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
These are not fatal errors, so do not alarm the user by filling the
logs with *** ERROR ***. Especially as we know that g4x CRT detection
is a little sticky.
On the one hand the errors are valid since they are warning us of a
stall -- we poll the register whilst holding the mode lock so not even
the mouse will update. On the other hand, those stalls were already present
yet nobody complained.
Reported-by: Andi Kleen <andi@firstfloor.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18332
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The drm device drivers currently allow seeking on the
character device but never care about the actual
file position.
When we change the default llseek operation to be
no_llseek, calling llseek on a drm device would
return an error condition, which is an API change.
Explicitly setting noop_llseek lets us keep the
current API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Later initialisation of the encoder often requires that
drm_encoder_init() has already been called, for instance, initialiasing
the DDC buses.
Yet another recent regression, as 819f3fb7 depended upon these fixes
which I missed when cherry-picking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
One problem with devices that share the DDC bus between the VGA and
DVI-I connectors is that with two devices attached we cannot know if
there is truly a monitor attached to the DVI connector. In this case, it
is preferrrable to mark the status as unknown, so that the user can
supply the known set of modes and continue to use the output.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We only need to use the analog encoder for rare devices which share the
DDC between the DVI-I and VGA connectors, so only create as needed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The texture base address registers are in units of 256 bytes.
The original CS checker treated these offsets as bytes, so the
original check was wrong. I fixed the units in a patch during
the 2.6.36 cycle, but this ended up breaking some existing
userspace (probably due to a bug in either userspace texture allocation
or the drm texture mipmap checker). So for now, until we come
up with a better fix, just warn if the mipmap size it too large.
This will keep existing userspace working and it should be just
as safe as before when we were checking the wrong units. These
are GPU MC addresses, so if they fall outside of the VRAM or
GART apertures, they end up at the GPU default page, so this should
be safe from a security perspective.
v2: Just disable the warning. It just spams the log and there's
nothing the user can do about it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The SDVO proxy i2c adapter wants to be able to use information stored in
the encoder, so pass that through intel_i2c rather than iterate over all
known encoders every time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we currently may need to acquire a fence register during a modeset,
we need to be able to do so in an uninterruptible manner. So expose that
parameter to the callers of the fence management code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This ensures that we do wait upon the flushes to complete if necessary
and avoid the visual tears, whilst enabling pipelined page-flips.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There has been periodic evidence that LVDS, on at least some
panels, prefers the dividers selected by the legacy pll algo.
This patch forces the use of the legacy pll algo on RV620
LVDS panels. The old behavior (new pll algo) can be selected
by setting the new_pll module parameter to 1.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30029
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not 100% sure this is due to BKL removal, its most likely a combination
of that + userspace timing changes in udev/plymouth. The drm adds the sysfs
device before the driver has completed internal loading, this causes udev
to make the node and plymouth to open it before we've completed loading.
The proper solution is to delay the sysfs manipulation until later in loading
however this causes knock on issues with sysfs connector nodes, so we can use
the global mutex to serialise loading and userspace opens.
Reported-by: Toni Spets (hifi on #radeon)
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: Julien Cristau pointed out that @nondestructive results in
double-negatives and confusion when trying to interpret the parameter,
so use @force instead. Much easier to type as well. ;-)
And fix the miscompilation of vmgfx reported by Sedat Dilek.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I pulled the wrong version of the patch from Daniel Vetter which was
missing the read barriers -- and the one that was causing all the trouble
was from i915_gem_object_put_fence_reg(), leading to GPU hangs on gen3.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By reducing the hangcheck frequency we check less often, conserving
resources, and still detect a lock up quickly. On a fast machine with a
slow GPU (like a Core2 paired with a 945G) it is easy for the hangcheck to
misfire as we check too fast.
Also once hung and if we fail to completely reset the chip, we have a
nasty habit of proclaming a hang many times a second and generating a
strobe-like display.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fix a regression in the previous regression fix...
In order to turn off the pipes entirely upon the first modeset, we
pretend that BIOS (or earlier module incarnation) left them active.
The first task performed by setup_initial_configuration() is to disable
all pipes and so to avoid skipping that step and so to ensure a known
configuration we need to mark all the crtcs as active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When separating out the prepare/commit into its own separate functions
we overlooked that the intel_crtc->dpms_mode was being used elsewhere to
check on the actual status of the pipe.
Track that bit of logic separately from the actual dpms mode, so there
is no confusion should we be able to handle multiple dpms modes, nor
any semantic conflict between prepare/commit and dpms.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This closes a couple of corner cases where we introduced and forgot
about a couple of routines that need to be called when disabling the
crtc and then re-enabling it. The code needs to be moved again so that
the common bits are shared across generations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This commit fixes bogus CS rejection if it contains a sequence
of the following operations:
- Set the color buffer 0. track->cb[i].robj becomes non-NULL.
- Render.
- Set a larger zbuffer than the previously-set color buffer.
- Set a larger scissor area as well.
- Set the color channel mask to 0 to do depth-only rendering.
- Render. --> rejected, because track->cb[i].robj remained non-NULL,
therefore the conditional checking for the color channel mask and
friends is not performed, and the larger scissor area causes
the rejection.
This fixes bugs:
- https://bugs.freedesktop.org/show_bug.cgi?id=29762
- https://bugs.freedesktop.org/show_bug.cgi?id=28869
And maybe some others which seem to look the same.
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
One subtest of mesa/demos/gltestperf takes 9 seconds to complete,
so to prevent an unnecessary gpu reset followed by a hardlock, I am
increasing the interval to 10 seconds after which a GPU is considered
in a locked-up state. This is on RV530. However, with a little slower GPU,
we would surpass the interval easily, so this is not a good fix
for gltestperf.
Nevertheless, this commit also fixes hardlocks in the applications which
render at speed of less than 1 frame per second, where the whole frame
consists of only one command stream. The game Tiny & Big is an example.
This bar is now lowered to 0.1 fps.
Now the question comes down to whether we should (often unsuccessfully)
reset the GPU at all? Once we have stable enough drivers, we won't have to.
Has the time come already?
If possible, this commit should go to stable as well.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch fixes rendering errors on some evergreen boards.
Hardcoding the backend map is not an optimal solution, but
a better fix is being worked on.
Similar to the fix for rv740
(6271901d82).
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29986
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Destructive load-detection is very expensive and due to failings
elsewhere can trigger system wide stalls of up to 600ms. A simple
first step to correcting this is not to invoke such an expensive
and destructive load-detection operation automatically.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16265
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise when disabling the output we switch to the new fb (which is
likely NULL) and skip the call to mode_set -- leaking driver private
state on the old_fb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29857
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
caused by d65d65b175
need to update the radeon crtc priv native mode before using it.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30049
v2: integrate v/h copy paste typo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I broke out my trusty i845 and found a new boot failure, which upon
inspection turned out to be a recursion within:
drm_helper_probe_single_connector_modes() -> drm_helper_hpd_irq_event()
-> intel_crt_detect() -> drm_helper_probe_single_connector_modes()
Calling drm_kms_helper_poll_enable() instead performs the desired
re-initialisation of the polling should the user have toggled the
parameter, without the recursive side-effect.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 77d07fd9d7 introduced a regression
where by not waiting for the panel to be turned off, left the panel and
PLL registers locked across the modeset. Thus the panel remaining blank.
As pointed out by Daniel Vetter, when testing LVDS it helps to open the
laptop and look at the actual panel you are purporting to test.
A second issue with the patch was that in order to modify the panel
fitter before gen5, the pipe and the panel must have be completely
powered down. So we wait.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The documentation says that an SDVO command takes a maximum of 15us to be
processed by the device, and that it is sufficient to read the status byte
3 times (whilst the command is still in the PENDING state) for the driver
to be confident that sufficient time has elapsed.
We err on the safe side and try 5 times before giving up.
The only question that remains: was the old behaviour derived by
experiments with real hardware?
A look into the murky history of UMS, implies that the behaviour was
accidental and the current retry mechanism was solely designed to catch
the status byte indicating PENDING with no reference to hardware
behaviour. (commit ac9181c014638dbeb334b40b4029d0ccb2b7a0fc in
xf86-video-intel)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Avoid a potentially long busy-wait if we not in the process of
atomically switching to the kdb console.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We just assume that it will happen in a timely manner. A variant of this
patch was first written and tested by Arjan van de Van.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Remove our redundant udelay() as the timings are already handled by the
i2c-algo-bit controller.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The purpose is to make the code much easier to read and therefore reduce
the possibility for bugs.
A side effect is that it also makes it much easier for the compiler,
reducing the object size by 4k -- from just a few functions!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Refactor the common code into seperate functions and use the MIN(large,
small) buffer calculation for self-refresh watermarks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
