If an error occurs after the first kzalloc() the corresponding memory
allocation is never freed.
Add the missing kfree() in the error handling path, as already done in the
remove() function.
Fixes: 7e773594da ("sfc: Separate efx_nic memory from net_device memory")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/dc114193121c52c8fa3779e49bdd99d4b41344a9.1667077009.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ndo_start_xmit() method must not free skb when returning
NETDEV_TX_BUSY, since caller is going to requeue freed skb.
Fix it by returning NETDEV_TX_OK in case of dma_map_single() fails.
Fixes: 79f339125e ("net: fec: Add software TSO support")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ADIN1110 was registering netdev_notifiers on each device probe.
This leads to warnings/probe failures because of double registration
of the same notifier when to adin1110/2111 devices are connected to
the same system.
Move the registration of netdev_notifiers in module init call,
in this way multiple driver instances can use the same notifiers.
Fixes: bc93e19d08 ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20221027095655.89890-2-alexandru.tachici@analog.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of generic description, mention what reset_lock actually
protects i.e. lock to serialize xmit and tx_timeout execution.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under memory pressure, enetc_refill_rx_ring() may fail, and when called
during the enetc_open() -> enetc_setup_rxbdr() procedure, this is not
checked for.
An extreme case of memory pressure will result in exactly zero buffers
being allocated for the RX ring, and in such a case it is expected that
hardware drops all RX packets due to lack of buffers.
This does not happen, because the reset-default value of the consumer
and produces index is 0, and this makes the ENETC think that all buffers
have been initialized and that it owns them (when in reality none were).
The hardware guide explains this best:
| Configure the receive ring producer index register RBaPIR with a value
| of 0. The producer index is initially configured by software but owned
| by hardware after the ring has been enabled. Hardware increments the
| index when a frame is received which may consume one or more BDs.
| Hardware is not allowed to increment the producer index to match the
| consumer index since it is used to indicate an empty condition. The ring
| can hold at most RBLENR[LENGTH]-1 received BDs.
|
| Configure the receive ring consumer index register RBaCIR. The
| consumer index is owned by software and updated during operation of the
| of the BD ring by software, to indicate that any receive data occupied
| in the BD has been processed and it has been prepared for new data.
| - If consumer index and producer index are initialized to the same
| value, it indicates that all BDs in the ring have been prepared and
| hardware owns all of the entries.
| - If consumer index is initialized to producer index plus N, it would
| indicate N BDs have been prepared. Note that hardware cannot start if
| only a single buffer is prepared due to the restrictions described in
| (2).
| - Software may write consumer index to match producer index anytime
| while the ring is operational to indicate all received BDs prior have
| been processed and new BDs prepared for hardware.
Normally, the value of rx_ring->rcir (consumer index) is brought in sync
with the rx_ring->next_to_use software index, but this only happens if
page allocation ever succeeded.
When PI==CI==0, the hardware appears to receive frames and write them to
DMA address 0x0 (?!), then set the READY bit in the BD.
The enetc_clean_rx_ring() function (and its XDP derivative) is naturally
not prepared to handle such a condition. It will attempt to process
those frames using the rx_swbd structure associated with index i of the
RX ring, but that structure is not fully initialized (enetc_new_page()
does all of that). So what happens next is undefined behavior.
To operate using no buffer, we must initialize the CI to PI + 1, which
will block the hardware from advancing the CI any further, and drop
everything.
The issue was seen while adding support for zero-copy AF_XDP sockets,
where buffer memory comes from user space, which can even decide to
supply no buffers at all (example: "xdpsock --txonly"). However, the bug
is present also with the network stack code, even though it would take a
very determined person to trigger a page allocation failure at the
perfect time (a series of ifup/ifdown under memory pressure should
eventually reproduce it given enough retries).
Fixes: d4fd0404c1 ("enetc: Introduce basic PF and VF ENETC ethernet drivers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20221027182925.3256653-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cited commit at rx sa update operation passes the sci object
attribute, in the wrong endianness and not as expected by the HW
effectively create malformed hw sa context in case of update rx sa
consequently, HW produces unexpected MACsec packets which uses this
sa.
Fix by passing sci to create macsec object with the correct endianness,
while at it add __force u64 to prevent sparse check error of type
"sparse: error: incorrect type in assignment".
Fixes: aae3454e4d ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-16-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cited commit produces a sparse check error of type
"sparse: error: restricted __be64 degrades to integer". The
offending line wrongly did a bitwise operation between two different
storage types one of 64 bit when the other smaller side is 16 bit
which caused the above sparse error, furthermore bitwise operation
usage here is wrong in the first place as the constant MACSEC_PORT_ES
is not a bitwise field.
Fix by using the right mask to get the lower 16 bit if the sci number,
and use comparison operator '==' instead of bitwise '&' operator.
Fixes: 3b20949cb2 ("net/mlx5e: Add MACsec RX steering rules")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-15-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cited commit adds the support for update/delete MACsec Rx SA,
naturally, these operations need to check if the SA in question exists
to update/delete the SA and return error code otherwise, however they
do just the opposite i.e. return with error if the SA exists
Fix by change the check to return error in case the SA in question does
not exist, adjust error message and code accordingly.
Fixes: aae3454e4d ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-14-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The cited commit at update rx sa operation passes object attributes
to MACsec object create function without initializing/setting all
attributes fields leaving some of them with garbage values, therefore
violating the implicit assumption at create object function, which
assumes that all input object attributes fields are set.
Fix by initializing the object attributes struct to zero, thus leaving
unset fields with the legal zero value.
Fixes: aae3454e4d ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Lior Nahmanson <liorna@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-13-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When setting Bluefield to DPU NIC mode using mlxconfig tool + sync
firmware reset flow, we run into scenario where the host was not
eswitch manager at the time of mlx5 driver load but becomes eswitch manager
after the sync firmware reset flow. This results in null pointer
access of mpfs structure during mac filter add. This change prevents null
pointer access but mpfs table entries will not be added.
Fixes: 5ec697446f ("net/mlx5: Add support for devlink reload action fw activate")
Signed-off-by: Suresh Devarakonda <ramad@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Bodong Wang <bodong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-12-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update devlink health fw fatal reporter state to "healthy" is needed by
strictly calling devlink_health_reporter_state_update() after recovery
was done by PCI error handler. This is needed when fw_fatal reporter was
triggered due to PCI error. Poll health is called and set reporter state
to error. Health recovery failed (since EEH didn't re-enable the PCI).
PCI handlers keep on recover flow and succeed later without devlink
acknowledgment. Fix this by adding devlink state update at the end of
the PCI handler recovery process.
Fixes: 6181e5cb75 ("devlink: add support for reporter recovery completion")
Signed-off-by: Roy Novich <royno@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-11-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On multi table split the driver creates a new attr instance with
data being copied from prev attr instance zeroing action flags.
Also need to reset dests properties to avoid incorrect dests per attr.
Fixes: 8300f22526 ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-10-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reject TC rules that forward from internal port to internal port
as it is not supported.
This include rules that are explicitly have internal port as
the filter device as well as rules that apply on tunnel interfaces
as the route device for the tunnel interface can be an internal
port.
Fixes: 27484f7170 ("net/mlx5e: Offload tc rules that redirect to ovs internal port")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-9-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mlx5 SQs must select the timestamp format explicitly according to the
active clock mode, select the current active timestamp mode so ASO SQ create
will succeed.
This fixes the following error prints when trying to create ipsec ASO SQ
while the timestamp format is real time mode.
mlx5_cmd_out_err:778:(pid 34874): CREATE_SQ(0x904) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xd61c0b), err(-22)
mlx5_aso_create_sq:285:(pid 34874): Failed to open aso wq sq, err=-22
mlx5e_ipsec_init:436:(pid 34874): IPSec initialization failed, -22
Fixes: cdd04f4d4d ("net/mlx5: Add support to create SQ and CQ for ASO")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reported-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-7-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently encap slow path rules just forward to software without
setting the chain id miss register, so driver doesn't restore
the chain, and packets hitting this rule will restart from tc chain
0 instead of continuing to the chain the encap rule was on.
Fix this by setting the chain id miss register to the chain id mapping.
Fixes: 8f1e0b97cc ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-6-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When tx_port_ts is set, the driver diverts all UPD traffic over PTP port
to a dedicated PTP-SQ. The SKBs are cached until the wire-CQE arrives.
When the packet size is greater then MTU, the firmware might drop it and
the packet won't be transmitted to the wire, hence the wire-CQE won't
reach the driver. In this case the SKBs are accumulated in the SKB fifo.
Add room check to consider the PTP-SQ SKB fifo, when the SKB fifo is
full, driver stops the queue resulting in a TX timeout. Devlink
TX-reporter can recover from it.
Fixes: 1880bc4e4a ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-5-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When 2nd flow rules arrives, it will merge together with the
1st one if matcher criteria is the same.
If merge fails, driver will rollback the merge contents, and
reject the 2nd rule. At rollback stage, matcher can't be
disconnected unconditionally, otherise the 1st rule can't be
hit anymore.
Add logic to check if the matcher should be disconnected or not.
Fixes: cc2295cd54 ("net/mlx5: DR, Improve steering for empty or RX/TX-only matchers")
Signed-off-by: Rongwei Liu <rongweil@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-4-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After firmware reset driver should verify firmware already enabled CRS
and became responsive to pci config cycles before restoring pci state.
Fix that by waiting till device_id is readable through PCI again.
Fixes: eabe8e5e88 ("net/mlx5: Handle sync reset now event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-3-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
An offloaded SA stops receiving after about 2^32 + replay_window
packets. For example, when SA reaches <seq-hi 0x1, seq 0x2c>, all
subsequent packets get dropped with SA-icv-failure (integrity_failed).
To reproduce the bug:
- ConnectX-6 Dx with crypto enabled (FW 22.30.1004)
- ipsec.conf:
nic-offload = yes
replay-window = 32
esn = yes
salifetime=24h
- Run netperf for a long time to send more than 2^32 packets
netperf -H <device-under-test> -t TCP_STREAM -l 20000
When 2^32 + replay_window packets are received, the replay window
moves from the 2nd half of subspace (overlap=1) to the 1st half
(overlap=0). The driver then updates the 'esn' value in NIC
(i.e. seq_hi) as follows.
seq_hi = xfrm_replay_seqhi(seq_bottom)
new esn in NIC = seq_hi + 1
The +1 increment is wrong, as seq_hi already contains the correct
seq_hi. For example, when seq_hi=1, the driver actually tells NIC to
use seq_hi=2 (esn). This incorrect esn value causes all subsequent
packets to fail integrity checks (SA-icv-failure). So, do not
increment.
Fixes: cb01008390 ("net/mlx5: IPSec, Add support for ESN")
Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20221026135153.154807-2-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Queueing packets doesn't guarantee their transmission. Update TX stats
after hardware confirms consuming submitted data.
This also fixes a possible race and NULL dereference.
bcm4908_enet_start_xmit() could try to access skb after freeing it in
the bcm4908_enet_poll_tx().
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 4feffeadbc ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221027112430.8696-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Avoid the PHY library call unnecessarily into the suspend/resume
functions by setting phydev->mac_managed_pm to true. The SYSTEMPORT
driver essentially does exactly what mdio_bus_phy_resume() does by
calling phy_resume().
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221025234201.2549360-1-f.fainelli@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If of_device_register() returns error, the of node and the
name allocated in dev_set_name() is leaked, call put_device()
to give up the reference that was set in device_initialize(),
so that of node is put in logical_port_release() and the name
is freed in kobject_cleanup().
Fixes: 1acf2318dd ("ehea: dynamic add / remove port")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221025130011.1071357-1-yangyingliang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The phylib callback is called after MAC driver's own resume callback is
called. For AVE driver, after resuming immediately, PHY state machine is
in PHY_NOLINK because there is a time lag from link-down to link-up due to
autoneg. The result is WARN_ON() dump in mdio_bus_phy_resume().
Since ave_resume() itself calls phy_resume(), AVE driver should manage
PHY PM. To indicate that MAC driver manages PHY PM, set
phydev->mac_managed_pm to true to avoid the unnecessary phylib call and
add missing phy_init_hw() to ave_resume().
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221024072227.24769-1-hayashi.kunihiko@socionext.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash:
Unhandled fault: external abort on non-linefetch (0x1008) at […]
due to this SoC has less registers in its FEC implementation compared to other
i.MX6 variants. Thus, a run-time decision is required to avoid access to
non-existing registers.
Fixes: a51d3ab507 ("net: fec: use a more proper compatible string for i.MX6UL type device")
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
while unbinding device.
Fixes: 8ca86fd83e ("net: Micrel KSZ8841/2 PCI Ethernet driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221024131338.2848959-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix setting bits for specific flow_type for GLQF_HASH_INSET register.
In previous version all of the bits were set only in hena register, while
in inset only one bit was set. In order for this working correctly on all
types of cards these bits needs to be set correctly for both hena and inset
registers.
Fixes: eb0dd6e4a3 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a reset was triggered on one VF with i40e_reset_vf
global PF state __I40E_VF_DISABLE was set on a PF until
the reset finished. If immediately after triggering reset
on one VF there is a request to reset on another
it will cause a hang on VF side because VF will be notified
of incoming reset but the reset will never happen because
of this global state, we will get such error message:
[ +4.890195] iavf 0000:86:02.1: Never saw reset
and VF will hang waiting for the reset to be triggered.
Fix this by introducing new VF state I40E_VF_STATE_RESETTING
that will be set on a VF if it is currently resetting instead of
the global __I40E_VF_DISABLE PF state.
Fixes: 3ba9bcb4b6 ("i40e: add locking around VF reset")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When enabling flow type for RSS hash via ethtool:
ethtool -N $pf rx-flow-hash tcp4|tcp6|udp4|udp6 s|d
the driver would fail to setup this setting on X722
device since it was using the mask on the register
dedicated for X710 devices.
Apply a different mask on the register when setting the
RSS hash for the X722 device.
When displaying the flow types enabled via ethtool:
ethtool -n $pf rx-flow-hash tcp4|tcp6|udp4|udp6
the driver would print wrong values for X722 device.
Fix this issue by testing masks for X722 device in
i40e_get_rss_hash_opts function.
Fixes: eb0dd6e4a3 ("i40e: Allow RSS Hash set with less than four parameters")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20221024100526.1874914-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RK3588(s) can have multiple gmac controllers.
Re-use rk3568 logic to distinguish them.
Fixes: 2f2b60a0ec ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20221021172422.88534-1-sebastian.reichel@collabora.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When a frame is sent using FDMA, the skb is mapped and then the mapped
address is given to an tx dcb that is different than the last used tx
dcb. Once the HW finish with this frame, it would generate an interrupt
and then the dcb can be reused and memory can be freed. For each dcb
there is an dcb buf that contains some meta-data(is used by PTP, is
it free). There is 1 to 1 relationship between dcb and dcb_buf.
The following issue was observed. That sometimes after changing the MTU
to allocate new tx dcbs and dcbs_buf, two frames were not
transmitted. The frames were not transmitted because when reloading the
tx dcbs, it was always presuming to use the first dcb but that was not
always happening. Because it could be that the last tx dcb used before
changing MTU was first dcb and then when it tried to get the next dcb it
would take dcb 1 instead of 0. Because it is supposed to take a
different dcb than the last used one. This can be fixed simply by
changing tx->last_in_use to -1 when the fdma is disabled to reload the
new dcb and dcbs_buff.
But there could be a different issue. For example, right after the frame
is sent, the MTU is changed. Now all the dcbs and dcbs_buf will be
cleared. And now get the interrupt from HW that it finished with the
frame. So when we try to clear the skb, it is not possible because we
lost all the dcbs_buf.
The solution here is to stop replacing the tx dcbs and dcbs_buf when
changing MTU because the TX doesn't care what is the MTU size, it is
only the RX that needs this information.
Fixes: 2ea1cbac26 ("net: lan966x: Update FDMA to change MTU.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20221021090711.3749009-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ndo_start_xmit() method must not free skb when returning
NETDEV_TX_BUSY, since caller is going to requeue freed skb.
Fixes: 504d4721ee ("MIPS: Lantiq: Add ethernet driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before 262f2b782e ("net: fman: Map the base address once"), the
physical address of the MAC was exposed to userspace in two places: via
sysfs and via SIOCGIFMAP. While this is not best practice, it is an
external ABI which is in use by userspace software.
The aforementioned commit inadvertently modified these addresses and
made them virtual. This constitutes and ABI break. Additionally, it
leaks the kernel's memory layout to userspace. Partially revert that
commit, reintroducing the resource back into struct mac_device, while
keeping the intended changes (the rework of the address mapping).
Fixes: 262f2b782e ("net: fman: Map the base address once")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5e_macsec_cleanup() routine has NULL pointer dereferencing if mlx5
device doesn't support MACsec (priv->macsec will be NULL).
While at it delete comment line, assignment and extra blank lines, so fix
everything in one patch.
Fixes: 1f53da6764 ("net/mlx5e: Create advanced steering operation (ASO) object for MACsec")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC is stopped with rtnl_lock held, and during the stop it cancels the
'service_task' work and free irqs.
However, if CONFIG_MACSEC is set, rtnl_lock is acquired both from
aq_nic_service_task and aq_linkstate_threaded_isr. Then a deadlock
happens if aq_nic_stop tries to cancel/disable them when they've already
started their execution.
As the deadlock is caused by rtnl_lock, it causes many other processes
to stall, not only atlantic related stuff.
Fix it by introducing a mutex that protects each NIC's macsec related
data, and locking it instead of the rtnl_lock from the service task and
the threaded IRQ.
Before this patch, all macsec data was protected with rtnl_lock, but
maybe not all of it needs to be protected. With this new mutex, further
efforts can be made to limit the protected data only to that which
requires it. However, probably it doesn't worth it because all macsec's
data accesses are infrequent, and almost all are done from macsec_ops
or ethtool callbacks, called holding rtnl_lock, so macsec_mutex won't
never be much contended.
The issue appeared repeteadly attaching and deattaching the NIC to a
bond interface. Doing that after this patch I cannot reproduce the bug.
Fixes: 62c1c2e606 ("net: atlantic: MACSec offload skeleton")
Reported-by: Li Liang <liali@redhat.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently `sp_indiff` is cleaned when driver is removed. This will
cause problem in multi-PF/multi-host case, considering one PF is
removed while another is still in use.
Since `sp_indiff` is the application firmware property, it should
only be cleaned when the firmware is unloaded. Now let management
firmware to clean it when necessary, driver only set it.
Fixes: b1e4f11e42 ("nfp: refine the ABI of getting `sp_indiff` info")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20221020081411.80186-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The offset 12 (bit-rate) of EEPROM SFP DAC (passive) cables is expected
to be in the range 0x64 to 0x68. However, the 5 meter and 7 meter Molex
passive cables have the rate ceiling 0x78 at offset 12.
Add a quirk for Molex passive cables to extend the rate ceiling to 0x78.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current XGBE code assumes that offset 6 of EEPROM SFP DAC (passive)
cables is NULL. However, some cables (the 5 meter and 7 meter Molex
passive cables) have non-zero data at offset 6. Fix the logic by moving
the passive cable check above the active checks, so as not to be
improperly identified as an active cable. This will fix the issue for
any passive cable that advertises 1000Base-CX in offset 6.
Fixes: abf0a1c2b2 ("amd-xgbe: Add support for SFP+ modules")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PLL control setting(RRC) is needed only in fixed PHY configuration to
fix the peer-peer issues. Without the PLL control setting, the link up
takes longer time in a fixed phy configuration.
Driver implements SW RRC for Autoneg On configuration, hence PLL control
setting (RRC) is not needed for AN On configuration, and can be skipped.
Also, PLL re-initialization is not needed for PHY Power Off and RRC
commands. Otherwise, they lead to mailbox errors. Added the changes
accordingly.
Fixes: daf182d360 ("net: amd-xgbe: Toggle PLL settings during rate change")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of using hardcoded values, use enumerations for mailbox command
and sub commands.
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link stability issues are noticed on Yellow carp platforms when Receiver
Reset Cycle is issued. Since the CDR workaround is disabled on these
platforms, the Receiver Reset Cycle is not needed.
So, avoid issuing rrc on Yellow carp platforms.
Fixes: dbb6c58b5a ("net: amd-xgbe: Add Support for Yellow Carp Ethernet device")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The `macb_resume`/`macb_suspend` methods already call the
`phylink_start`/`phylink_stop` methods during their execution so
explicitly say that the PM of the PHY is done by MAC by using the
`mac_managed_pm` flag of the `struct phylink_config`.
This also fixes the warning message issued during resume:
WARNING: CPU: 0 PID: 237 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0x144/0x148
Depends-on: 96de900ae7 ("net: phylink: add mac_managed_pm in phylink_config structure")
Fixes: 744d23c71a ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221019120929.63098-1-sergiu.moga@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In hinic_vf_func_init(), if VF fails to register information with PF
through the MBOX, the MBOX callback function of VF is released once. But
it is released again in hinic_init_hwdev(). Remove one.
Fixes: 7dd29ee128 ("hinic: add sriov feature support")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When hinic_set_cmdq_depth() fails in hinic_init_cmdqs(), the cmdq memory is
not released correctly. Fix it.
Fixes: 72ef908bb3 ("hinic: add three net_device_ops of vf")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the input parameter idx meets the expected case option in
hinic_dbg_get_func_table(), read_data is not released. Fix it.
Fixes: 5215e16244 ("hinic: add support to query function table")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The value of lli_credit_cnt is incorrectly assigned, fix it.
Fixes: a0337c0dee ("hinic: add support to set and get irq coalesce")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the rx drop is calculated as the sum of multiple HW drop
counters. The issue is that not all the HW drop counters were added for
the rx drop counter. So if for example you have a police that drops
frames, they were not see in the rx drop counter.
Fix this by updating how the rx drop counter is calculated. It is
required to add also RX_RED_PRIO_* HW counters.
Fixes: 12c2d0a5b8 ("net: lan966x: add ethtool configuration and statistics")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20221019083056.2744282-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If phy_device_register() fails, phy_device_free() need be called to
put refcount, so memory of phy device and device name can be freed
in callback function.
If get_phy_device() fails, mdiobus_unregister() need be called,
or it will cause warning in mdiobus_free() and kobject is leaked.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221019064104.3228892-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
