This is not needed when firmware connection manager is run so limit this
to software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Alex reported that after rebooting the other host the peer-to-peer link
does not come up anymore. The reason for this is that the host that was
not rebooted tries to send the UUID request only 10 times according to
the USB4 Inter-Domain spec and gives up if it does not get reply. Then
when the other side is actually ready it cannot get the link established
anymore. The USB4 Inter-Domain spec requires that the discovery protocol
is restarted in that case so implement this now.
Reported-by: Alex Balcanquall <alex@alexbal.com>
Fixes: 8e1de70425 ("thunderbolt: Add support for XDomain lane bonding")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
David reported that cppcheck found following possible copy & paste
error from tmu_mode_init():
tmu.c:385:50: style: Expression is always false because 'else if' condition matches previous condition at line 383. [multiCondition]
And indeed this is a bug. Fix it to use correct index
(TB_SWITCH_TMU_MODE_HIFI_UNI).
Reported-by: David Binderman <dcb314@hotmail.com>
Fixes: d49b4f043d ("thunderbolt: Add support for enhanced uni-directional TMU mode")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Marek reported that when BlackMagic UltraStudio device is connected the
kernel repeatedly tries to enable lane bonding without success making
the device non-functional. It looks like the device does not have lane 1
connected at all so even though it is enabled we should not try to bond
the lanes. For this reason check that lane 1 is in fact CL0 (connected,
active) before attempting to bond the lanes.
Reported-by: Marek Šanta <teslan223@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217737
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
On some systems the IOMMU blocks the first couple of driver ready
messages to the connection manager firmware as can be seen in below
excerpts:
thunderbolt 0000:06:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0010 address=0xbb0e3400 flags=0x0020]
or
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [04:00.0] PASID ffffffff fault addr 69974000 [fault reason 05] PTE Write access is not set
The reason is unknown and hard to debug because we were not able to
reproduce this locally. This only happens on certain systems with Intel
Maple Ridge Thunderbolt controller. If there is a device connected when
the driver is loaded the issue does not happen either. Only when there
is nothing connected (so typically when the system is booted up).
We can work this around by sending the driver ready several times. After
a couple of retries the message goes through and the controller works
just fine. For this reason make the number of retries a parameter for
icm_request() and then for Maple Ridge (and Titan Ridge as they us the
same function but this should not matter) increase number of retries
while shortening the timeout accordingly.
Reported-by: Werner Sembach <wse@tuxedocomputers.com>
Reported-by: Konrad J Hambrick <kjhambrick@gmail.com>
Reported-by: Calvin Walton <calvin.walton@kepstin.ca>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=214259
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes following Thunderbolt/USB4 changes for the v6.6 merge
window:
- Replace broken mailing list address in the ABI document
- Small improvements.
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=US+s
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.6 merge window
This includes following Thunderbolt/USB4 changes for the v6.6 merge
window:
- Replace broken mailing list address in the ABI document
- Small improvements.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
Documentation/ABI: thunderbolt: Replace 01.org in contact
thunderbolt: Check Intel vendor ID in tb_switch_get_generation()
thunderbolt: Log a warning if device links are not found
thunderbolt: Set variable tmu_params storage class specifier to static
Only Intel made Thunderbolt 1-3 devices so to avoid possible confusion
check for the Intel vendor ID before deciding the device generation.
While there move the USB4 check to happen first.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The software connection manager needs the device links in order to
establish the tunnels before the native protocols so log a warning if
they are not found.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The memory allocated in tb_queue_dp_bandwidth_request() needs to be
released once the request is handled to avoid leaking it.
Fixes: 6ce3563520 ("thunderbolt: Add support for DisplayPort bandwidth allocation mode")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Previously, on unplug events, the TMU mode was disabled first
followed by the Time Synchronization Handshake, irrespective of
whether the tb_switch_tmu_rate_write() API was successful or not.
However, this caused a problem with Thunderbolt 3 (TBT3)
devices, as the TSPacketInterval bits were always enabled by default,
leading the host router to assume that the device router's TMU was
already enabled and preventing it from initiating the Time
Synchronization Handshake. As a result, TBT3 monitors experienced
display flickering from the second hot plug onwards.
To address this issue, we have modified the code to only disable the
Time Synchronization Handshake during TMU disable if the
tb_switch_tmu_rate_write() function is successful. This ensures that
the TBT3 devices function correctly and eliminates the display
flickering issue.
Co-developed-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
smatch reports
drivers/thunderbolt/tmu.c:30:3: warning: symbol
'tmu_params' was not declared. Should it be static?
This variable is only used in its defining file so should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Barlow Ridge Thunderbolt controller has 3 DP IN adapters. This
allows 3 simultaneus DisplayPort tunnels through either one or two USB4
downstream ports (in any possible configuration). Add test case for
this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This adds support for the UHBR (Ultra High Bit Rate) bandwidths
introduced with DisplayPort 2.0 (and refined in 2.1). These can go up to
80 Gbit/s and their support is represent in additional bits in the DP IN
capability.
This updates the DisplayPort tunneling to support these new rates too.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make sure the DisplayPort bandwidth allocation mode function names are
consistent with the existing ones, such as USB3.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For USB4 v2 routers we can also enable CL2 which allows better power
savings and thermal management than CL0s and CL1.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is new TMU mode introduced with the USB4 v2. This mode is simpler
than the existing ones and allows all CL states as well. Enable this for
all links where both side routers are v2 and keep the existing
functionality for the v1 and earlier links.
Currently only support the MedRes rate. We can add the HiFi rate later
too if it turns out to be useful.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Barlow Ridge discrete USB4 controller has larger NOR Flash, hence
increase NVM_MAX_SIZE to support it.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Move constants related to NVM into nvm.c to make the code cleaner. Use a
separate constant for USB4_DATA_DWORDS in usb4.c.
No functional changes.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Barlow Ridge discrete USB4 host router has the same limitation as
the previous generations so make sure the USB3 bandwidth limitation
quirk is applied to Barlow Ridge too.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Barlow Ridge is the first USB4 v2 controller from Intel. The
controller exposes standard USB4 PCI class ID in typical configurations,
however there is a way to configure it so that it uses a special class
ID to allow using s different driver than the Windows inbox one. For
this reason add the Barlow Ridge PCI ID to the Linux driver too so that
the driver can attach regardless of the class ID.
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For USB4 v2 routers, the PCIe adapter capability length is longer.
Display the correct capability length in the debugfs register dump.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For USB4 v2 routers, the DisplayPort IN adapter capability length is
longer. Display the correct capability length in the debugfs register
dump.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For USB4 v2 routers, the adapters's TMU capability has two additional
double words. Include them in the debugfs register dump.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 spec introduces modified encapsulation of PCIe TLP and DLLP
packets. This improves the PCIe tunneled traffic usage by reducing
overhead. Enable this if both sides of the link support it.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Program the CMUV (Connection Manager USB4 Version) field for USB4 v2 and
v1 routers according to the spec.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 added a bit that can be used to reset the host router so we use
this to trigger reset when the driver probes. This will reset the
already connected topology as well but doing this simplifies things a
lot if for instance the link is already set to asymmetric. We also add
a module parameter to prevent this in case of problems.
While there rename the REG_HOP_COUNT to REG_CAPS to match the USB4 spec
naming better.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 spec adds a bunch of new notifications that the connection
manager can use instead of polling. While we do not use these yet we
need to ack the ones routers expect to be acked.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 bumps the per-lane speed up to 40 Gb/s. Also the lanes are
always bonded which gives 80 Gb/s symmetric link (and 120/40 Gb/s
asymmetric). This updates the speed and width of routers and XDomain
connections to support the Gen 4 link. For now we keep the link as is
even if it is already asymmetric.
While there make tb_port_set_link_width() static.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add a new function usb4_switch_version() that can be used to figure out
the spec version of the router and make tb_switch_is_usb4() to use it as
well. Update the uevent accordingly.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It is not required to be implemented at all because USB4 does not use
lane 1 for tunneling except when aggregated with lane 0. For this reason
do not try to read the path config space of USB4 lane 1 adapters.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is also something not always updated after the DROM contents itself
so issue warning but continue parsing it as we do for pre-USB4 DROMs
too.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When USB4 port is in offline mode (this mean there is no device
attached) we want to keep the sideband up to make it possible to
communicate with the retimers. In the same way there is no need to
enable sideband transactions when the USB4 port is not offline as they
are already up.
For this reason make the enabling/disabling depend on the USB4 port
offline status.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Once retimer NVM authentication is started, sending UNSET_INBOUND_SBTX
will fail so avoid doing that. Only send it when we are writing an image
with not authentication or when the authentication failed early.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to the USB4 retimer guide the correct order is immediately
after sending ENUMERATE_RETIMERS so update the code to follow this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tunnels between hosts should not have CL states enabled because
otherwise they might enter a low power state without the other end
noticing which causes packets to be lost. For this reason disable all
CL states upon first DMA tunnel creation. Once the last DMA tunnel is
torn down we try to re-enable them.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This allows us to disable all CL states temporarily when running lane
margining and then return back the previously enabled states.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In case the boot firmware enabled any of them, read the currently
configured CL states and update the router structure accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes it easier to spot from the logs and follows what we do with
the TMU code already. We also log enabling/disabling CL states using the
tb_sw_dbg() instead of tb_port_dbg().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is really no need to call any of the CLx functions in the TMU code
so remove all these checks. This makes the TMU enable/disable flows
easier to follow as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently tb_switch_clx_enable() enables CL states only for the first
depth router. This is something we may want to change in the future and
in addition it is not visible from the calling path at all. For this
reason do the check in the tb.c so it is immediately visible that we
only do this for the first depth router. Fix the kernel-docs
accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is more natural and follows the hardware register layout better.
This makes it easier to see which CL states we enable (even though they
should be enabled together). Rename 'clx_mask' to 'clx' everywhere as
this is now always bitmask.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This avoids some duplication and makes the flow slightly easier to
understand. Also follows what we do in tb_enable_tmu().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
No need to have separate functions for these so fold them into
tb_switch_clx_enable() and tb_switch_clx_disable() accordingly.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There really don't belong to switch.c so move them into their own file.
As we do this rename the functions to match the conventions used
elsewhere in the driver.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no need to duplicate the code the enables TMU. Also update the
comment to better explain why we do this in the first place.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is better to be part of the software connection manager flows in
tb.c. Also name the new function tb_increase_tmu_accuracy() to match
what it actually does.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now this is split into two with one having a misleading name
(tb_switch_tmu_unidirectional_enable()).
Make this easier to read, rename and consolidate the two functions into
one with name that explains what it actually does. Use the two constants
as well that were added but never used to make it clear which bits are
being set.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no point passing it as we already have a field for that. While
there clean up the kernel-doc of things that do not really belong to the
API documentation (these can be figured out from the spec itself).
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Drop extra empty line and get rid of the '__' in function names. No
functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In the same way we did for the routers add a function that returns the
parent routers downstream facing port for XDomain devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Introduce tb_switch_downstream_port() helper function that returns the
downstream port of a parent switch that is connected to the upstream
port of specified switch. From now on, we use it all across the driver
where applicable.
While there fix a whitespace in comment and rename 'downstream' to
'down' to be consistent with the rest of the driver.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When resuming from system sleep states the driver issues following
warning on Intel hardware:
thunderbolt 0000:07:00.0: interrupt for TX ring 0 is already enabled
The reason for this is that the commit in question did not mask the ring
interrupt on Intel hardware leaving the interrupt active. Fix this by
masking it also in Intel hardware.
Reported-by: beld zhang <beldzhang@gmail.com>
Tested-by: beld zhang <beldzhang@gmail.com>
Closes: https://lore.kernel.org/linux-usb/ZHKW5NeabmfhgLbY@debian.me/
Fixes: c4af8e3fec ("thunderbolt: Clear registers properly when auto clear isn't in use")
Cc: stable@vger.kernel.org
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If the boot firmware has already established tunnels, especially ones
that have special requirements from the link such as DisplayPort, we
should not blindly enable CL states (nor change the TMU configuration).
Otherwise the existing tunnels may not work as expected.
For this reason, skip the CL state enabling when we go over the existing
topology. This will also keep the TMU settings untouched because we do
not change the TMU configuration when CL states are not enabled.
Reported-by: Koba Ko <koba.ko@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7831
Cc: stable@vger.kernel.org # v6.0+
Acked-By: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It turns out that when plugging in VGA cable through USB-C to VGA/DVI
dongle the Connection Manager handshake can take longer time, at least
on Intel Titan Ridge based docks such as Dell WD91TB. This leads to
following error in the dmesg:
thunderbolt 0000:00:0d.3: 3:10: DP tunnel activation failed, aborting
and the display stays blank (because we failed to establish the tunnel).
For this reason increase the timeout to 3s.
Reported-by: Koba Ko <koba.ko@canonical.com>
Cc: stable@vger.kernel.org
Acked-By: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make the description match the core driver and the networking with
Thunderbolt/USB4 prefix. No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The default ones should be find but this allows the user to tweak the
credits to get more performance out of the P2P connection.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add a debug log to this quirk as well so we can see what quirks have
been applied when debugging.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Ring 0 cannot be used for anything else than control channel messages.
For this reason add a check to tb_tunnel_alloc_dma() and fail if someone
tries to do that.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Both tb_xdomain_enable_paths() and tb_xdomain_disable_paths() expect -1,
not 0, if the corresponding ring is not needed. For this reason change
the driver to use correct value for the rings that are not needed.
Fixes: 180b068942 ("thunderbolt: Allow multiple DMA tunnels over a single XDomain connection")
Cc: stable@vger.kernel.org
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Tested-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When `QUIRK_AUTO_CLEAR_INT` isn't set, interrupt masking should be
cleared by writing to Interrupt Mask Clear (IMR) and interrupt
status should be cleared properly at shutdown/init.
This fixes an error where interrupts are left enabled during resume
from hibernation with `CONFIG_USB4=y`.
Fixes: 468c49f447 ("thunderbolt: Disable interrupt auto clear for rings")
Cc: stable@vger.kernel.org # v6.3
Reported-by: Takashi Iwai <tiwai@suse.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217343
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This includes following Thunderbolt/USB4 changes for the v6.4 merge
window:
- Refactoring of DROM read code paths
- Convert to use SI units from units.h
- A couple of cleanups
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=IcG3
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.4 merge window
This includes following Thunderbolt/USB4 changes for the v6.4 merge
window:
- Refactoring of DROM read code paths
- Convert to use SI units from units.h
- A couple of cleanups
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Introduce usb4_port_sb_opcode_err_to_errno() helper
thunderbolt: Make use of SI units from units.h
thunderbolt: Get rid of redundant 'else'
thunderbolt: Refactor DROM reading
thunderbolt: use `tb_eeprom_get_drom_offset` to discover DROM offset
The usb4_port_sb_opcode_err_to_errno() converts from USB4 error codes
to the Linux errno space. In particular, this makes the intention
of the repeating usb4_port_retimer_read() call in the
usb4_port_retimer_nvm_authenticate_status() clearer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In a couple of places it seems reasonable to use MEGA intead
of explicit number. It makes code more readable and robust.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
cppcheck reports
drivers/thunderbolt/nhi.c:74:7: style: Local variable 'bit' shadows outer variable [shadowVariable]
int bit;
^
drivers/thunderbolt/nhi.c:66:6: note: Shadowed declaration
int bit = ring_interrupt_index(ring) & 31;
^
drivers/thunderbolt/nhi.c:74:7: note: Shadow variable
int bit;
^
For readablity rename the outer to interrupt_bit and the innner
to auto_clear_bit.
Fixes: 468c49f447 ("thunderbolt: Disable interrupt auto clear for ring")
Cc: stable@vger.kernel.org
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When interrupt auto clear is programmed, any read to the interrupt
status register will clear all interrupts. If two interrupts have
come in before one can be serviced then this will cause lost interrupts.
On AMD USB4 routers this has manifested in odd problems particularly
with long strings of control tranfers such as reading the DROM via bit
banging.
Instead of clearing interrupts automatically, clear the bit corresponding
to the given ring's interrupt in the ISR.
Fixes: 7a1808f82a ("thunderbolt: Handle ring interrupt by reading interrupt status register")
Cc: Sanju Mehta <Sanju.Mehta@amd.com>
Cc: stable@vger.kernel.org
Tested-by: Anson Tsao <anson.tsao@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
`ring_interrupt_index` doesn't change the data for `ring` so mark it as
const. This is needed by the following patch that disables interrupt
auto clear for rings.
Cc: Sanju Mehta <Sanju.Mehta@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The NVM reading code has a series of gotos that potentially introduce
unexpected behaviors with retries if something unexpected has failed
to parse.
Refactor the code to remove the gotos and drop the retry logic.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
[mw: renamed root switch to host router, split device handling too]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The static function `tb_eeprom_get_drom_offset` has more safety guards
for the DROM offset fetching. Use this instead of just `tb_sw_read`
No intended functional changes.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When tunneling aggregated USB3 (20 Gb/s) the bandwidth values that are
programmed to the ADP_USB3_CS_2 go higher than 4096 and that does not
fit anymore to the 12-bit field. Fix this by scaling the value using
the scale field accordingly.
Fixes: 3b1d8d577c ("thunderbolt: Implement USB3 bandwidth negotiation routines")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Current Intel USB4 host routers have hardware limitation that the USB3
bandwidth cannot go higher than 16376 Mb/s. Work this around by adding a
new quirk that limits the bandwidth for the affected host routers.
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to apply quirks based on certain adapter types move call to
tb_check_quirks() happen after the adapters are initialized. This should
not affect the existing quirks.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to USB4 retimer specification, the process of firmware update
sequence requires issuing a SET_INBOUND_SBTX port operation that later
shall be followed by UNSET_INBOUND_SBTX port operation. This last step
is not currently issued by the driver but it is necessary to make sure
the retimers are put back to passthrough mode even during enumeration.
If this step is missing the link may not come up properly after
soft-reboot for example.
For this reason issue UNSET_INBOUND_SBTX after SET_INBOUND_SBTX for
enumeration and also when the NVM upgrade is run.
Reported-by: Christian Schaubschläger <christian.schaubschlaeger@gmx.at>
Link: https://lore.kernel.org/linux-usb/b556f5ed-5ee8-9990-9910-afd60db93310@gmx.at/
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Memory for the usb4->margining needs to be relased for the upstream port
of the router as well, even though the debugfs directory gets released
with the router device removal. Fix this.
Fixes: d0f1e0c2a6 ("thunderbolt: Add support for receiver lane margining")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add QUIRK_NO_CLX to disable the CLx state for hardware which
doesn't supports it.
AMD Yellow Carp and Pink Sardine don't support CLx state,
hence disabling it using QUIRK_NO_CLX.
Cc: stable@vger.kernel.org
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
[mw: added debug log when the quirk is run]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
This includes following Thunderbolt/USB4 changes for the v6.3 merge
window:
- Add support for DisplayPort bandwidth allocation mode
- Debug logging improvements
- Minor cleanups.
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=Kegw
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.3 merge window
This includes following Thunderbolt/USB4 changes for the v6.3 merge
window:
- Add support for DisplayPort bandwidth allocation mode
- Debug logging improvements
- Minor cleanups.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Add missing kernel-doc comment to tb_tunnel_maximum_bandwidth()
thunderbolt: Handle bandwidth allocation mode enablement notification
thunderbolt: Add support for DisplayPort bandwidth allocation mode
thunderbolt: Include the additional DP IN double word in debugfs dump
thunderbolt: Add functions to support DisplayPort bandwidth allocation mode
thunderbolt: Increase timeout of DP OUT adapter handshake
thunderbolt: Take CL states into account when waiting for link to come up
thunderbolt: Improve debug logging in tb_available_bandwidth()
thunderbolt: Log DP adapter type
thunderbolt: Use decimal port number in control and tunnel logs too
thunderbolt: Refactor tb_acpi_add_link()
thunderbolt: Use correct type in tb_port_is_clx_enabled() prototype
The uevent() callback in struct device_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jilin Yuan <yuanjilin@cdjrlc.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Gross <markgross@kernel.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Sanyog Kale <sanyog.r.kale@intel.com>
Cc: Sean Young <sean@mess.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Won Chung <wonchung@google.com>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # for Thunderbolt
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the graphics side enables bandwidth allocation mode the DP IN
adapter sends notification to the connection manager about this.
Currently the handler misses this and tries to allocate 0 Mb/s that then
makes the graphics side to think the request failed.
Fix this by properly handling the enablement notification.
Fixes: 6ce3563520 ("thunderbolt: Add support for DisplayPort bandwidth allocation mode")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 spec defines an optional feature that allows the connection
manager to negotiate with the graphics through DPCD registers changes in
the bandwidth allocation dynamically. This is referred as "bandwidth
allocation mode" in the spec. The connection manager uses DP IN adapters
registers to communicate with the graphics, and also gets notifications
from these adapters when the graphics wants to change the bandwidth
allocation. Both the connection manager and the graphics driver needs to
support this.
We check if the DP IN adapter supports this and if it does enable it
before establishing a DP tunnel. Then we react on DP_BW notifications
coming from the DP IN adapter and update the bandwidth allocation
accordingly (within the maximum common capabilities the DP IN/OUT
support).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When DisplayPort bandwidth allocation mode is supported by the DP IN
adapter it has an extra double word in the adapter config space. Include
this in the debugfs register dump.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec defines an additional feature that DP IN adapters can
implement (alongside with the graphics DPCD register set) to support
more dynamic bandwidth management for DisplayPort tunnels. For the
connection manager the communication happens through the DP IN adapter
using a set of registers in the adapter config space allocated for this.
Add functions that export this functionality for the rest of the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Sometimes the current timeout is not enough so increase it to 1500 ms
and while there make the loop use ktime instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If CL states are enabled for the link it may be in these states too when
reading the lane adapter state but it will enter CL0 as soon as there is
traffic in the high-speed lanes. Upon discovery we want to make sure
that is accounted as the link being up, otherwise we end up tearing down
the topology with no good reason.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes it easier to see what is going on when bandwidth is being
allocated for tunneling.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes it easier to see from the debug logs what type of DisplayPort
adapter is in use or available.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use decimal number instead of hex in port numbers as we have been doing
with other logging functions too. This makes the output more consistent.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When firmware connection manager is in use we should not touch the lane
adapter (well or any) configuration space so do this only when we know
that the software connection manager is active.
Fixes: 8e1de70425 ("thunderbolt: Add support for XDomain lane bonding")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to take minimum of both sides of the USB3 link into consideration,
not just the downstream port. Fix this by calling tb_usb3_max_link_rate()
instead.
Fixes: 0bd680cd90 ("thunderbolt: Add USB3 bandwidth management")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We cannot call PM runtime functions in tb_retimer_scan() because it will
also be called when retimers are scanned from userspace (happens when
there is no device connected on ChromeOS for instance) and at the same
USB4 port runtime resume hook. This leads to hang because neither can
proceed.
Fix this by runtime resuming USB4 ports in tb_scan_port() instead. This
makes sure the ports are runtime PM active when retimers are added under
it while avoiding the reported hang as well.
Reported-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Fixes: 1e56c88ade ("thunderbolt: Runtime resume USB4 port when retimers are scanned")
Cc: stable@vger.kernel.org
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Convert while loop into do-while with only a single call to
acpi_get_first_physical_node(). No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Mika Westerberg