Write error handling is racy and can sometime lead to the error recovery
path wrongly changing the inode size of a sequential zone file to an
incorrect value which results in garbage data being readable at the end
of a file. There are 2 problems:
1) zonefs_file_dio_write() updates a zone file write pointer offset
after issuing a direct IO with iomap_dio_rw(). This update is done
only if the IO succeed for synchronous direct writes. However, for
asynchronous direct writes, the update is done without waiting for
the IO completion so that the next asynchronous IO can be
immediately issued. However, if an asynchronous IO completes with a
failure right before the i_truncate_mutex lock protecting the update,
the update may change the value of the inode write pointer offset
that was corrected by the error path (zonefs_io_error() function).
2) zonefs_io_error() is called when a read or write error occurs. This
function executes a report zone operation using the callback function
zonefs_io_error_cb(), which does all the error recovery handling
based on the current zone condition, write pointer position and
according to the mount options being used. However, depending on the
zoned device being used, a report zone callback may be executed in a
context that is different from the context of __zonefs_io_error(). As
a result, zonefs_io_error_cb() may be executed without the inode
truncate mutex lock held, which can lead to invalid error processing.
Fix both problems as follows:
- Problem 1: Perform the inode write pointer offset update before a
direct write is issued with iomap_dio_rw(). This is safe to do as
partial direct writes are not supported (IOMAP_DIO_PARTIAL is not
set) and any failed IO will trigger the execution of zonefs_io_error()
which will correct the inode write pointer offset to reflect the
current state of the one on the device.
- Problem 2: Change zonefs_io_error_cb() into zonefs_handle_io_error()
and call this function directly from __zonefs_io_error() after
obtaining the zone information using blkdev_report_zones() with a
simple callback function that copies to a local stack variable the
struct blk_zone obtained from the device. This ensures that error
handling is performed holding the inode truncate mutex.
This change also simplifies error handling for conventional zone files
by bypassing the execution of report zones entirely. This is safe to
do because the condition of conventional zones cannot be read-only or
offline and conventional zone files are always fully mapped with a
constant file size.
Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: 8dcc1a9d90 ("fs: New zonefs file system")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCZZ/BCAAKCRBZ7Krx/gZQ
68qqAQD6LtfYLDJGdJM+lNpyiG4BA7coYpPlJtmH7mzL+MbFPgEAnM7XsK6zyvza
3+rEggLM0UFWjg9Ln7Nlq035TeYtFwo=
=w1mD
-----END PGP SIGNATURE-----
Merge tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc filesystem updates from Al Viro:
"Misc cleanups (the part that hadn't been picked by individual fs
trees)"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
apparmorfs: don't duplicate kfree_link()
orangefs: saner arguments passing in readdir guts
ocfs2_find_match(): there's no such thing as NULL or negative ->d_parent
reiserfs_add_entry(): get rid of pointless namelen checks
__ocfs2_add_entry(), ocfs2_prepare_dir_for_insert(): namelen checks
ext4_add_entry(): ->d_name.len is never 0
befs: d_obtain_alias(ERR_PTR(...)) will do the right thing
affs: d_obtain_alias(ERR_PTR(...)) will do the right thing
/proc/sys: use d_splice_alias() calling conventions to simplify failure exits
hostfs: use d_splice_alias() calling conventions to simplify failure exits
udf_fiiter_add_entry(): check for zero ->d_name.len is bogus...
udf: d_obtain_alias(ERR_PTR(...)) will do the right thing...
udf: d_splice_alias() will do the right thing on ERR_PTR() inode
nfsd: kill stale comment about simple_fill_super() requirements
bfs_add_entry(): get rid of pointless ->d_name.len checks
nilfs2: d_obtain_alias(ERR_PTR(...)) will do the right thing...
zonefs: d_splice_alias() will do the right thing on ERR_PTR() inode
There were already assertions that we were not passing a tail page to
error_remove_page(), so make the compiler enforce that by converting
everything to pass and use a folio.
Link: https://lkml.kernel.org/r/20231117161447.2461643-7-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
* Make large writes to the page cache fill sparse parts of the cache
with large folios, then use large memcpy calls for the large folio.
* Track the per-block dirty state of each large folio so that a
buffered write to a single byte on a large folio does not result in a
(potentially) multi-megabyte writeback IO.
* Allow some directio completions to be performed in the initiating
task's context instead of punting through a workqueue. This will
reduce latency for some io_uring requests.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ2qTKExjcn+O1o2YRKO3ySh0YRpgUCZM0Z1AAKCRBKO3ySh0YR
pp7BAQCzkKejCM0185tNIH/faHjzidSisNQkJ5HoB4Opq9U66AEA6IPuAdlPlM/J
FPW1oPq33Yn7AV4wXjUNFfDLzVb/Fgg=
=dFBU
-----END PGP SIGNATURE-----
Merge tag 'iomap-6.6-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull iomap updates from Darrick Wong:
"We've got some big changes for this release -- I'm very happy to be
landing willy's work to enable large folios for the page cache for
general read and write IOs when the fs can make contiguous space
allocations, and Ritesh's work to track sub-folio dirty state to
eliminate the write amplification problems inherent in using large
folios.
As a bonus, io_uring can now process write completions in the caller's
context instead of bouncing through a workqueue, which should reduce
io latency dramatically. IOWs, XFS should see a nice performance bump
for both IO paths.
Summary:
- Make large writes to the page cache fill sparse parts of the cache
with large folios, then use large memcpy calls for the large folio.
- Track the per-block dirty state of each large folio so that a
buffered write to a single byte on a large folio does not result in
a (potentially) multi-megabyte writeback IO.
- Allow some directio completions to be performed in the initiating
task's context instead of punting through a workqueue. This will
reduce latency for some io_uring requests"
* tag 'iomap-6.6-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (26 commits)
iomap: support IOCB_DIO_CALLER_COMP
io_uring/rw: add write support for IOCB_DIO_CALLER_COMP
fs: add IOCB flags related to passing back dio completions
iomap: add IOMAP_DIO_INLINE_COMP
iomap: only set iocb->private for polled bio
iomap: treat a write through cache the same as FUA
iomap: use an unsigned type for IOMAP_DIO_* defines
iomap: cleanup up iomap_dio_bio_end_io()
iomap: Add per-block dirty state tracking to improve performance
iomap: Allocate ifs in ->write_begin() early
iomap: Refactor iomap_write_delalloc_punch() function out
iomap: Use iomap_punch_t typedef
iomap: Fix possible overflow condition in iomap_write_delalloc_scan
iomap: Add some uptodate state handling helpers for ifs state bitmap
iomap: Drop ifs argument from iomap_set_range_uptodate()
iomap: Rename iomap_page to iomap_folio_state and others
iomap: Copy larger chunks from userspace
iomap: Create large folios in the buffered write path
filemap: Allow __filemap_get_folio to allocate large folios
filemap: Add fgf_t typedef
...
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCZOXTKAAKCRCRxhvAZXjc
oifJAQCzi/p+AdQu8LA/0XvR7fTwaq64ZDCibU4BISuLGT2kEgEAuGbuoFZa0rs2
XYD/s4+gi64p9Z01MmXm2XO1pu3GPg0=
=eJz5
-----END PGP SIGNATURE-----
Merge tag 'v6.6-vfs.ctime' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs timestamp updates from Christian Brauner:
"This adds VFS support for multi-grain timestamps and converts tmpfs,
xfs, ext4, and btrfs to use them. This carries acks from all relevant
filesystems.
The VFS always uses coarse-grained timestamps when updating the ctime
and mtime after a change. This has the benefit of allowing filesystems
to optimize away a lot of metadata updates, down to around 1 per
jiffy, even when a file is under heavy writes.
Unfortunately, this has always been an issue when we're exporting via
NFSv3, which relies on timestamps to validate caches. A lot of changes
can happen in a jiffy, so timestamps aren't sufficient to help the
client decide to invalidate the cache.
Even with NFSv4, a lot of exported filesystems don't properly support
a change attribute and are subject to the same problems with timestamp
granularity. Other applications have similar issues with timestamps
(e.g., backup applications).
If we were to always use fine-grained timestamps, that would improve
the situation, but that becomes rather expensive, as the underlying
filesystem would have to log a lot more metadata updates.
This introduces fine-grained timestamps that are used when they are
actively queried.
This uses the 31st bit of the ctime tv_nsec field to indicate that
something has queried the inode for the mtime or ctime. When this flag
is set, on the next mtime or ctime update, the kernel will fetch a
fine-grained timestamp instead of the usual coarse-grained one.
As POSIX generally mandates that when the mtime changes, the ctime
must also change the kernel always stores normalized ctime values, so
only the first 30 bits of the tv_nsec field are ever used.
Filesytems can opt into this behavior by setting the FS_MGTIME flag in
the fstype. Filesystems that don't set this flag will continue to use
coarse-grained timestamps.
Various preparatory changes, fixes and cleanups are included:
- Fixup all relevant places where POSIX requires updating ctime
together with mtime. This is a wide-range of places and all
maintainers provided necessary Acks.
- Add new accessors for inode->i_ctime directly and change all
callers to rely on them. Plain accesses to inode->i_ctime are now
gone and it is accordingly rename to inode->__i_ctime and commented
as requiring accessors.
- Extend generic_fillattr() to pass in a request mask mirroring in a
sense the statx() uapi. This allows callers to pass in a request
mask to only get a subset of attributes filled in.
- Rework timestamp updates so it's possible to drop the @now
parameter the update_time() inode operation and associated helpers.
- Add inode_update_timestamps() and convert all filesystems to it
removing a bunch of open-coding"
* tag 'v6.6-vfs.ctime' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs: (107 commits)
btrfs: convert to multigrain timestamps
ext4: switch to multigrain timestamps
xfs: switch to multigrain timestamps
tmpfs: add support for multigrain timestamps
fs: add infrastructure for multigrain timestamps
fs: drop the timespec64 argument from update_time
xfs: have xfs_vn_update_time gets its own timestamp
fat: make fat_update_time get its own timestamp
fat: remove i_version handling from fat_update_time
ubifs: have ubifs_update_time use inode_update_timestamps
btrfs: have it use inode_update_timestamps
fs: drop the timespec64 arg from generic_update_time
fs: pass the request_mask to generic_fillattr
fs: remove silly warning from current_time
gfs2: fix timestamp handling on quota inodes
fs: rename i_ctime field to __i_ctime
selinux: convert to ctime accessor functions
security: convert to ctime accessor functions
apparmor: convert to ctime accessor functions
sunrpc: convert to ctime accessor functions
...
Commit 16d7fd3cfa ("zonefs: use iomap for synchronous direct writes")
changes zonefs code from a self-built zone append BIO to using iomap for
synchronous direct writes. This change relies on iomap submit BIO
callback to change the write BIO built by iomap to a zone append BIO.
However, this change overlooked the fact that a write BIO may be very
large as it is split when issued. The change from a regular write to a
zone append operation for the built BIO can result in a block layer
warning as zone append BIO are not allowed to be split.
WARNING: CPU: 18 PID: 202210 at block/bio.c:1644 bio_split+0x288/0x350
Call Trace:
? __warn+0xc9/0x2b0
? bio_split+0x288/0x350
? report_bug+0x2e6/0x390
? handle_bug+0x41/0x80
? exc_invalid_op+0x13/0x40
? asm_exc_invalid_op+0x16/0x20
? bio_split+0x288/0x350
bio_split_rw+0x4bc/0x810
? __pfx_bio_split_rw+0x10/0x10
? lockdep_unlock+0xf2/0x250
__bio_split_to_limits+0x1d8/0x900
blk_mq_submit_bio+0x1cf/0x18a0
? __pfx_iov_iter_extract_pages+0x10/0x10
? __pfx_blk_mq_submit_bio+0x10/0x10
? find_held_lock+0x2d/0x110
? lock_release+0x362/0x620
? mark_held_locks+0x9e/0xe0
__submit_bio+0x1ea/0x290
? __pfx___submit_bio+0x10/0x10
? seqcount_lockdep_reader_access.constprop.0+0x82/0x90
submit_bio_noacct_nocheck+0x675/0xa20
? __pfx_bio_iov_iter_get_pages+0x10/0x10
? __pfx_submit_bio_noacct_nocheck+0x10/0x10
iomap_dio_bio_iter+0x624/0x1280
__iomap_dio_rw+0xa22/0x18a0
? lock_is_held_type+0xe3/0x140
? __pfx___iomap_dio_rw+0x10/0x10
? lock_release+0x362/0x620
? zonefs_file_write_iter+0x74c/0xc80 [zonefs]
? down_write+0x13d/0x1e0
iomap_dio_rw+0xe/0x40
zonefs_file_write_iter+0x5ea/0xc80 [zonefs]
do_iter_readv_writev+0x18b/0x2c0
? __pfx_do_iter_readv_writev+0x10/0x10
? inode_security+0x54/0xf0
do_iter_write+0x13b/0x7c0
? lock_is_held_type+0xe3/0x140
vfs_writev+0x185/0x550
? __pfx_vfs_writev+0x10/0x10
? __handle_mm_fault+0x9bd/0x1c90
? find_held_lock+0x2d/0x110
? lock_release+0x362/0x620
? find_held_lock+0x2d/0x110
? lock_release+0x362/0x620
? __up_read+0x1ea/0x720
? do_pwritev+0x136/0x1f0
do_pwritev+0x136/0x1f0
? __pfx_do_pwritev+0x10/0x10
? syscall_enter_from_user_mode+0x22/0x90
? lockdep_hardirqs_on+0x7d/0x100
do_syscall_64+0x58/0x80
This error depends on the hardware used, specifically on the max zone
append bytes and max_[hw_]sectors limits. Tests using AMD Epyc machines
that have low limits did not reveal this issue while runs on Intel Xeon
machines with larger limits trigger it.
Manually splitting the zone append BIO using bio_split_rw() can solve
this issue but also requires issuing the fragment BIOs synchronously
with submit_bio_wait(), to avoid potential reordering of the zone append
BIO fragments, which would lead to data corruption. That is, this
solution is not better than using regular write BIOs which are subject
to serialization using zone write locking at the IO scheduler level.
Given this, fix the issue by removing zone append support and using
regular write BIOs for synchronous direct writes. This allows preseving
the use of iomap and having identical synchronous and asynchronous
sequential file write path. Zone append support will be reintroduced
later through io_uring commands to ensure that the needed special
handling is done correctly.
Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: 16d7fd3cfa ("zonefs: use iomap for synchronous direct writes")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
When filesystem blocksize is less than folio size (either with
mapping_large_folio_support() or with blocksize < pagesize) and when the
folio is uptodate in pagecache, then even a byte write can cause
an entire folio to be written to disk during writeback. This happens
because we currently don't have a mechanism to track per-block dirty
state within struct iomap_folio_state. We currently only track uptodate
state.
This patch implements support for tracking per-block dirty state in
iomap_folio_state->state bitmap. This should help improve the filesystem
write performance and help reduce write amplification.
Performance testing of below fio workload reveals ~16x performance
improvement using nvme with XFS (4k blocksize) on Power (64K pagesize)
FIO reported write bw scores improved from around ~28 MBps to ~452 MBps.
1. <test_randwrite.fio>
[global]
ioengine=psync
rw=randwrite
overwrite=1
pre_read=1
direct=0
bs=4k
size=1G
dir=./
numjobs=8
fdatasync=1
runtime=60
iodepth=64
group_reporting=1
[fio-run]
2. Also our internal performance team reported that this patch improves
their database workload performance by around ~83% (with XFS on Power)
Reported-by: Aravinda Herle <araherle@in.ibm.com>
Reported-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
In later patches, we're going to change how the inode's ctime field is
used. Switch to using accessor functions instead of raw accesses of
inode->i_ctime.
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230705190309.579783-81-jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
- Yosry has also eliminated cgroup's atomic rstat flushing.
- Nhat Pham adds the new cachestat() syscall. It provides userspace
with the ability to query pagecache status - a similar concept to
mincore() but more powerful and with improved usability.
- Mel Gorman provides more optimizations for compaction, reducing the
prevalence of page rescanning.
- Lorenzo Stoakes has done some maintanance work on the get_user_pages()
interface.
- Liam Howlett continues with cleanups and maintenance work to the maple
tree code. Peng Zhang also does some work on maple tree.
- Johannes Weiner has done some cleanup work on the compaction code.
- David Hildenbrand has contributed additional selftests for
get_user_pages().
- Thomas Gleixner has contributed some maintenance and optimization work
for the vmalloc code.
- Baolin Wang has provided some compaction cleanups,
- SeongJae Park continues maintenance work on the DAMON code.
- Huang Ying has done some maintenance on the swap code's usage of
device refcounting.
- Christoph Hellwig has some cleanups for the filemap/directio code.
- Ryan Roberts provides two patch series which yield some
rationalization of the kernel's access to pte entries - use the provided
APIs rather than open-coding accesses.
- Lorenzo Stoakes has some fixes to the interaction between pagecache
and directio access to file mappings.
- John Hubbard has a series of fixes to the MM selftesting code.
- ZhangPeng continues the folio conversion campaign.
- Hugh Dickins has been working on the pagetable handling code, mainly
with a view to reducing the load on the mmap_lock.
- Catalin Marinas has reduced the arm64 kmalloc() minimum alignment from
128 to 8.
- Domenico Cerasuolo has improved the zswap reclaim mechanism by
reorganizing the LRU management.
- Matthew Wilcox provides some fixups to make gfs2 work better with the
buffer_head code.
- Vishal Moola also has done some folio conversion work.
- Matthew Wilcox has removed the remnants of the pagevec code - their
functionality is migrated over to struct folio_batch.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZJejewAKCRDdBJ7gKXxA
joggAPwKMfT9lvDBEUnJagY7dbDPky1cSYZdJKxxM2cApGa42gEA6Cl8HRAWqSOh
J0qXCzqaaN8+BuEyLGDVPaXur9KirwY=
=B7yQ
-----END PGP SIGNATURE-----
Merge tag 'mm-stable-2023-06-24-19-15' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull mm updates from Andrew Morton:
- Yosry Ahmed brought back some cgroup v1 stats in OOM logs
- Yosry has also eliminated cgroup's atomic rstat flushing
- Nhat Pham adds the new cachestat() syscall. It provides userspace
with the ability to query pagecache status - a similar concept to
mincore() but more powerful and with improved usability
- Mel Gorman provides more optimizations for compaction, reducing the
prevalence of page rescanning
- Lorenzo Stoakes has done some maintanance work on the
get_user_pages() interface
- Liam Howlett continues with cleanups and maintenance work to the
maple tree code. Peng Zhang also does some work on maple tree
- Johannes Weiner has done some cleanup work on the compaction code
- David Hildenbrand has contributed additional selftests for
get_user_pages()
- Thomas Gleixner has contributed some maintenance and optimization
work for the vmalloc code
- Baolin Wang has provided some compaction cleanups,
- SeongJae Park continues maintenance work on the DAMON code
- Huang Ying has done some maintenance on the swap code's usage of
device refcounting
- Christoph Hellwig has some cleanups for the filemap/directio code
- Ryan Roberts provides two patch series which yield some
rationalization of the kernel's access to pte entries - use the
provided APIs rather than open-coding accesses
- Lorenzo Stoakes has some fixes to the interaction between pagecache
and directio access to file mappings
- John Hubbard has a series of fixes to the MM selftesting code
- ZhangPeng continues the folio conversion campaign
- Hugh Dickins has been working on the pagetable handling code, mainly
with a view to reducing the load on the mmap_lock
- Catalin Marinas has reduced the arm64 kmalloc() minimum alignment
from 128 to 8
- Domenico Cerasuolo has improved the zswap reclaim mechanism by
reorganizing the LRU management
- Matthew Wilcox provides some fixups to make gfs2 work better with the
buffer_head code
- Vishal Moola also has done some folio conversion work
- Matthew Wilcox has removed the remnants of the pagevec code - their
functionality is migrated over to struct folio_batch
* tag 'mm-stable-2023-06-24-19-15' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (380 commits)
mm/hugetlb: remove hugetlb_set_page_subpool()
mm: nommu: correct the range of mmap_sem_read_lock in task_mem()
hugetlb: revert use of page_cache_next_miss()
Revert "page cache: fix page_cache_next/prev_miss off by one"
mm/vmscan: fix root proactive reclaim unthrottling unbalanced node
mm: memcg: rename and document global_reclaim()
mm: kill [add|del]_page_to_lru_list()
mm: compaction: convert to use a folio in isolate_migratepages_block()
mm: zswap: fix double invalidate with exclusive loads
mm: remove unnecessary pagevec includes
mm: remove references to pagevec
mm: rename invalidate_mapping_pagevec to mapping_try_invalidate
mm: remove struct pagevec
net: convert sunrpc from pagevec to folio_batch
i915: convert i915_gpu_error to use a folio_batch
pagevec: rename fbatch_count()
mm: remove check_move_unevictable_pages()
drm: convert drm_gem_put_pages() to use a folio_batch
i915: convert shmem_sg_free_table() to use a folio_batch
scatterlist: add sg_set_folio()
...
-----BEGIN PGP SIGNATURE-----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=zP4Y
-----END PGP SIGNATURE-----
Merge tag 'for-6.5/block-2023-06-23' of git://git.kernel.dk/linux
Pull block updates from Jens Axboe:
- NVMe pull request via Keith:
- Various cleanups all around (Irvin, Chaitanya, Christophe)
- Better struct packing (Christophe JAILLET)
- Reduce controller error logs for optional commands (Keith)
- Support for >=64KiB block sizes (Daniel Gomez)
- Fabrics fixes and code organization (Max, Chaitanya, Daniel
Wagner)
- bcache updates via Coly:
- Fix a race at init time (Mingzhe Zou)
- Misc fixes and cleanups (Andrea, Thomas, Zheng, Ye)
- use page pinning in the block layer for dio (David)
- convert old block dio code to page pinning (David, Christoph)
- cleanups for pktcdvd (Andy)
- cleanups for rnbd (Guoqing)
- use the unchecked __bio_add_page() for the initial single page
additions (Johannes)
- fix overflows in the Amiga partition handling code (Michael)
- improve mq-deadline zoned device support (Bart)
- keep passthrough requests out of the IO schedulers (Christoph, Ming)
- improve support for flush requests, making them less special to deal
with (Christoph)
- add bdev holder ops and shutdown methods (Christoph)
- fix the name_to_dev_t() situation and use cases (Christoph)
- decouple the block open flags from fmode_t (Christoph)
- ublk updates and cleanups, including adding user copy support (Ming)
- BFQ sanity checking (Bart)
- convert brd from radix to xarray (Pankaj)
- constify various structures (Thomas, Ivan)
- more fine grained persistent reservation ioctl capability checks
(Jingbo)
- misc fixes and cleanups (Arnd, Azeem, Demi, Ed, Hengqi, Hou, Jan,
Jordy, Li, Min, Yu, Zhong, Waiman)
* tag 'for-6.5/block-2023-06-23' of git://git.kernel.dk/linux: (266 commits)
scsi/sg: don't grab scsi host module reference
ext4: Fix warning in blkdev_put()
block: don't return -EINVAL for not found names in devt_from_devname
cdrom: Fix spectre-v1 gadget
block: Improve kernel-doc headers
blk-mq: don't insert passthrough request into sw queue
bsg: make bsg_class a static const structure
ublk: make ublk_chr_class a static const structure
aoe: make aoe_class a static const structure
block/rnbd: make all 'class' structures const
block: fix the exclusive open mask in disk_scan_partitions
block: add overflow checks for Amiga partition support
block: change all __u32 annotations to __be32 in affs_hardblocks.h
block: fix signed int overflow in Amiga partition support
block: add capacity validation in bdev_add_partition()
block: fine-granular CAP_SYS_ADMIN for Persistent Reservation
block: disallow Persistent Reservation on partitions
reiserfs: fix blkdev_put() warning from release_journal_dev()
block: fix wrong mode for blkdev_get_by_dev() from disk_scan_partitions()
block: document the holder argument to blkdev_get_by_path
...
-----BEGIN PGP SIGNATURE-----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=KhW4
-----END PGP SIGNATURE-----
Merge tag 'for-6.5/splice-2023-06-23' of git://git.kernel.dk/linux
Pull splice updates from Jens Axboe:
"This kills off ITER_PIPE to avoid a race between truncate,
iov_iter_revert() on the pipe and an as-yet incomplete DMA to a bio
with unpinned/unref'ed pages from an O_DIRECT splice read. This causes
memory corruption.
Instead, we either use (a) filemap_splice_read(), which invokes the
buffered file reading code and splices from the pagecache into the
pipe; (b) copy_splice_read(), which bulk-allocates a buffer, reads
into it and then pushes the filled pages into the pipe; or (c) handle
it in filesystem-specific code.
Summary:
- Rename direct_splice_read() to copy_splice_read()
- Simplify the calculations for the number of pages to be reclaimed
in copy_splice_read()
- Turn do_splice_to() into a helper, vfs_splice_read(), so that it
can be used by overlayfs and coda to perform the checks on the
lower fs
- Make vfs_splice_read() jump to copy_splice_read() to handle
direct-I/O and DAX
- Provide shmem with its own splice_read to handle non-existent pages
in the pagecache. We don't want a ->read_folio() as we don't want
to populate holes, but filemap_get_pages() requires it
- Provide overlayfs with its own splice_read to call down to a lower
layer as overlayfs doesn't provide ->read_folio()
- Provide coda with its own splice_read to call down to a lower layer
as coda doesn't provide ->read_folio()
- Direct ->splice_read to copy_splice_read() in tty, procfs, kernfs
and random files as they just copy to the output buffer and don't
splice pages
- Provide wrappers for afs, ceph, ecryptfs, ext4, f2fs, nfs, ntfs3,
ocfs2, orangefs, xfs and zonefs to do locking and/or revalidation
- Make cifs use filemap_splice_read()
- Replace pointers to generic_file_splice_read() with pointers to
filemap_splice_read() as DIO and DAX are handled in the caller;
filesystems can still provide their own alternate ->splice_read()
op
- Remove generic_file_splice_read()
- Remove ITER_PIPE and its paraphernalia as generic_file_splice_read
was the only user"
* tag 'for-6.5/splice-2023-06-23' of git://git.kernel.dk/linux: (31 commits)
splice: kdoc for filemap_splice_read() and copy_splice_read()
iov_iter: Kill ITER_PIPE
splice: Remove generic_file_splice_read()
splice: Use filemap_splice_read() instead of generic_file_splice_read()
cifs: Use filemap_splice_read()
trace: Convert trace/seq to use copy_splice_read()
zonefs: Provide a splice-read wrapper
xfs: Provide a splice-read wrapper
orangefs: Provide a splice-read wrapper
ocfs2: Provide a splice-read wrapper
ntfs3: Provide a splice-read wrapper
nfs: Provide a splice-read wrapper
f2fs: Provide a splice-read wrapper
ext4: Provide a splice-read wrapper
ecryptfs: Provide a splice-read wrapper
ceph: Provide a splice-read wrapper
afs: Provide a splice-read wrapper
9p: Add splice_read wrapper
net: Make sock_splice_read() use copy_splice_read() by default
tty, proc, kernfs, random: Use copy_splice_read()
...
Since commit a2ad63daa8 ("VFS: add FMODE_CAN_ODIRECT file flag") file
systems can just set the FMODE_CAN_ODIRECT flag at open time instead of
wiring up a dummy direct_IO method to indicate support for direct I/O.
Do that for zonefs so that noop_direct_IO can eventually be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Remove the function zonefs_file_dio_append() that is used to manually
issue REQ_OP_ZONE_APPEND BIOs for processing synchronous direct writes
and use iomap instead.
To preserve the use of zone append operations for synchronous writes,
different struct iomap_dio_ops are defined. For synchronous direct
writes using zone append, zonefs_zone_append_dio_ops is introduced.
The submit_bio operation of this structure is defined as the function
zonefs_file_zone_append_dio_submit_io() which is used to change the BIO
opreation for synchronous direct IO writes to REQ_OP_ZONE_APPEND.
In order to preserve the write location check on completion of zone
append BIOs, the end_io operation is also defined using the function
zonefs_file_zone_append_dio_bio_end_io(). This check now relies on the
zonefs_zone_append_bio structure, allocated together with zone append
BIOs with a dedicated BIO set. This structure include the target inode
of a zone append BIO as well as the target append offset location for
the zone append operation. This is used to perform a check against
bio->bi_iter.bi_sector when the BIO completes, without needing to use
the zone information z_wpoffset field, thus removing the need for
taking the inode truncate mutex.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
All callers of iomap_file_buffered_write need to updated ki_pos, move it
into common code.
Link: https://lkml.kernel.org/r/20230601145904.1385409-8-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andreas Gruenbacher <agruenba@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Anna Schumaker <anna@kernel.org>
Cc: Chao Yu <chao@kernel.org>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Miklos Szeredi <mszeredi@redhat.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The zonefs superblock reading code uses bio_add_page() to add a page to a
newly created bio. bio_add_page() can fail, but the return value is
never checked.
Use __bio_add_page() as adding a single page to a newly created bio is
guaranteed to succeed.
This brings us a step closer to marking bio_add_page() as __must_check.
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/04c9978ccaa0fc9871cd4248356638d98daccf0c.1685532726.git.johannes.thumshirn@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Provide a splice_read wrapper for zonefs. This does some checks before
proceeding and locks the inode across the call to filemap_splice_read() and
a size check in case of truncation. Splicing from direct I/O is handled by
the caller.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Christoph Hellwig <hch@lst.de>
cc: Al Viro <viro@zeniv.linux.org.uk>
cc: Jens Axboe <axboe@kernel.dk>
cc: Darrick J. Wong <djwong@kernel.org>
cc: linux-xfs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
cc: linux-block@vger.kernel.org
cc: linux-mm@kvack.org
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230522135018.2742245-26-dhowells@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The call to invalidate_inode_pages2_range() in __iomap_dio_rw() may
fail, in which case -ENOTBLK is returned and this error code is
propagated back to user space trhough iomap_dio_rw() ->
zonefs_file_dio_write() return chain. This error code is fairly obscure
and may confuse the user. Avoid this and be consistent with the behavior
of zonefs_file_dio_append() for similar invalidate_inode_pages2_range()
errors by returning -EBUSY to user space when iomap_dio_rw() returns
-ENOTBLK.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Fixes: 8dcc1a9d90 ("fs: New zonefs file system")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
When a direct append write is executed, the append offset may correspond
to the last page of a sequential file inode which might have been cached
already by buffered reads, page faults with mmap-read or non-direct
readahead. To ensure that the on-disk and cached data is consistant for
such last cached page, make sure to always invalidate it in
zonefs_file_dio_append(). If the invalidation fails, return -EBUSY to
userspace to differentiate from IO errors.
This invalidation will always be a no-op when the FS block size (device
zone write granularity) is equal to the page size (e.g. 4K).
Reported-by: Hans Holmberg <Hans.Holmberg@wdc.com>
Fixes: 02ef12a663 ("zonefs: use REQ_OP_ZONE_APPEND for sync DIO")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Tested-by: Hans Holmberg <hans.holmberg@wdc.com>
Since the expected write location in a sequential file is always at the
end of the file (append write), when an invalid write append location is
detected in zonefs_file_dio_append(), print the invalid written location
instead of the expected write location.
Fixes: a608da3bd7 ("zonefs: Detect append writes at invalid locations")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
In zonefs_file_dio_append(), initialize the variable size to 0 to
prevent compilation and static code analizers warning such as:
New smatch warnings:
fs/zonefs/file.c:441 zonefs_file_dio_append() error: uninitialized
symbol 'size'.
The warning is a false positive as size is never actually used
uninitialized.
No functional change.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202303191227.GL8Dprbi-lkp@intel.com/
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
* Reorganize zonefs code to split file related operations to a new
fs/zonefs/file.c file. From me.
* Modify zonefs to use dynamically allocated inodes and dentries
(using the inode and dentry caches) instead of statically allocating
everything on mount. This saves a significant amount of memory for
very large zoned block devices with 10s of thousands of zones. From
me.
* Make zonefs_sb_ktype a const struct kobj_type, from Thomas.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCY/VokQAKCRDdoc3SxdoY
dgCVAP427Q2wBrphU1//iW6R/7OZMz24nwmJcYPBAVLTngQO5gD+IVX+ru4xhD4Q
W1VKFN9QIDbjEiEc+Lmt9iQuDz+roAI=
=e/FD
-----END PGP SIGNATURE-----
Merge tag 'zonefs-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull zonefs updates from Damien Le Moal:
- Reorganize zonefs code to split file related operations to a new
fs/zonefs/file.c file (me)
- Modify zonefs to use dynamically allocated inodes and dentries (using
the inode and dentry caches) instead of statically allocating
everything on mount. This saves a significant amount of memory for
very large zoned block devices with 10s of thousands of zones (me)
- Make zonefs_sb_ktype a const struct kobj_type (Thomas)
* tag 'zonefs-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: make kobj_type structure constant
zonefs: Cache zone group directory inodes
zonefs: Dynamically create file inodes when needed
zonefs: Separate zone information from inode information
zonefs: Reduce struct zonefs_inode_info size
zonefs: Simplify IO error handling
zonefs: Reorganize code
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCY+5NlQAKCRCRxhvAZXjc
orOaAP9i2h3OJy95nO2Fpde0Bt2UT+oulKCCcGlvXJ8/+TQpyQD/ZQq47gFQ0EAz
Br5NxeyGeecAb0lHpFz+CpLGsxMrMwQ=
=+BG5
-----END PGP SIGNATURE-----
Merge tag 'fs.idmapped.v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping
Pull vfs idmapping updates from Christian Brauner:
- Last cycle we introduced the dedicated struct mnt_idmap type for
mount idmapping and the required infrastucture in 256c8aed2b ("fs:
introduce dedicated idmap type for mounts"). As promised in last
cycle's pull request message this converts everything to rely on
struct mnt_idmap.
Currently we still pass around the plain namespace that was attached
to a mount. This is in general pretty convenient but it makes it easy
to conflate namespaces that are relevant on the filesystem with
namespaces that are relevant on the mount level. Especially for
non-vfs developers without detailed knowledge in this area this was a
potential source for bugs.
This finishes the conversion. Instead of passing the plain namespace
around this updates all places that currently take a pointer to a
mnt_userns with a pointer to struct mnt_idmap.
Now that the conversion is done all helpers down to the really
low-level helpers only accept a struct mnt_idmap argument instead of
two namespace arguments.
Conflating mount and other idmappings will now cause the compiler to
complain loudly thus eliminating the possibility of any bugs. This
makes it impossible for filesystem developers to mix up mount and
filesystem idmappings as they are two distinct types and require
distinct helpers that cannot be used interchangeably.
Everything associated with struct mnt_idmap is moved into a single
separate file. With that change no code can poke around in struct
mnt_idmap. It can only be interacted with through dedicated helpers.
That means all filesystems are and all of the vfs is completely
oblivious to the actual implementation of idmappings.
We are now also able to extend struct mnt_idmap as we see fit. For
example, we can decouple it completely from namespaces for users that
don't require or don't want to use them at all. We can also extend
the concept of idmappings so we can cover filesystem specific
requirements.
In combination with the vfs{g,u}id_t work we finished in v6.2 this
makes this feature substantially more robust and thus difficult to
implement wrong by a given filesystem and also protects the vfs.
- Enable idmapped mounts for tmpfs and fulfill a longstanding request.
A long-standing request from users had been to make it possible to
create idmapped mounts for tmpfs. For example, to share the host's
tmpfs mount between multiple sandboxes. This is a prerequisite for
some advanced Kubernetes cases. Systemd also has a range of use-cases
to increase service isolation. And there are more users of this.
However, with all of the other work going on this was way down on the
priority list but luckily someone other than ourselves picked this
up.
As usual the patch is tiny as all the infrastructure work had been
done multiple kernel releases ago. In addition to all the tests that
we already have I requested that Rodrigo add a dedicated tmpfs
testsuite for idmapped mounts to xfstests. It is to be included into
xfstests during the v6.3 development cycle. This should add a slew of
additional tests.
* tag 'fs.idmapped.v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping: (26 commits)
shmem: support idmapped mounts for tmpfs
fs: move mnt_idmap
fs: port vfs{g,u}id helpers to mnt_idmap
fs: port fs{g,u}id helpers to mnt_idmap
fs: port i_{g,u}id_into_vfs{g,u}id() to mnt_idmap
fs: port i_{g,u}id_{needs_}update() to mnt_idmap
quota: port to mnt_idmap
fs: port privilege checking helpers to mnt_idmap
fs: port inode_owner_or_capable() to mnt_idmap
fs: port inode_init_owner() to mnt_idmap
fs: port acl to mnt_idmap
fs: port xattr to mnt_idmap
fs: port ->permission() to pass mnt_idmap
fs: port ->fileattr_set() to pass mnt_idmap
fs: port ->set_acl() to pass mnt_idmap
fs: port ->get_acl() to pass mnt_idmap
fs: port ->tmpfile() to pass mnt_idmap
fs: port ->rename() to pass mnt_idmap
fs: port ->mknod() to pass mnt_idmap
fs: port ->mkdir() to pass mnt_idmap
...
Since commit ee6d3dd4ed ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definition to prevent
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Since looking up any zone file inode requires looking up first the inode
for the directory representing the zone group of the file, ensuring that
the zone group inodes are always cached is desired. To do so, take an
extra reference on the zone groups directory inodes on mount, thus
avoiding the eviction of these inodes from the inode cache until the
volume is unmounted.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Allocating and initializing all inodes and dentries for all files
results in a very large memory usage with high capacity zoned block
devices. For instance, with a 26 TB SMR HDD with over 96000 zones,
mounting the disk with zonefs results in about 130 MB of memory used,
the vast majority of this space being used for vfs inodes and dentries.
However, since a user will rarely access all zones at the same time,
dynamically creating file inodes and dentries on demand, similarly to
regular file systems, can significantly reduce memory usage.
This patch modifies mount processing to not create the inodes and
dentries for zone files. Instead, the directory inode operation
zonefs_lookup() and directory file operation zonefs_readdir() are
introduced to allocate and initialize inodes on-demand using the helper
functions zonefs_get_dir_inode() and zonefs_get_zgroup_inode().
Implementation of these functions is simple, relying on the static
nature of zonefs directories and files. Directory inodes are linked to
the volume zone groups (struct zonefs_zone_group) they represent by
using the directory inode i_private field. This simplifies the
implementation of the lookup and readdir operations.
Unreferenced zone file inodes can be evicted from the inode cache at any
time. In such case, the only inode information that cannot be recreated
from the zone information that is saved in the zone group data
structures attached to the volume super block is the inode uid, gid and
access rights. These values may have been changed by the user. To keep
these attributes for the life time of the mount, as before, the inode
mode, uid and gid are saved in the inode zone information and the saved
values are used to initialize regular file inodes when an inode lookup
happens. The zone information mode, uid and gid are initialized in
zonefs_init_zgroup() using the default values.
With these changes, the static minimal memory usage of a zonefs volume
is mostly reduced to the array of zone information for each zone group.
For the 26 TB SMR hard-disk mentioned above, the memory usage after
mount becomes about 5.4 MB, a reduction by a factor of 24 from the
initial 130 MB memory use.
Co-developed-by: Jorgen Hansen <Jorgen.Hansen@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
In preparation for adding dynamic inode allocation, separate an inode
zone information from the zonefs inode structure. The new data structure
zonefs_zone is introduced to store in memory information about a zone
that must be kept throughout the lifetime of the device mount.
Linking between a zone file inode and its zone information is done by
setting the inode i_private field to point to a struct zonefs_zone.
Using the i_private pointer avoids the need for adding a pointer in
struct zonefs_inode_info. Beside the vfs inode, this structure is
reduced to a mutex and a write open counter.
One struct zonefs_zone is created per file inode on mount. These
structures are organized in an array using the new struct
zonefs_zone_group data structure to represent zone groups. The
zonefs_zone arrays are indexed per file number (the index of a struct
zonefs_zone in its array directly gives the file number/name for that
zone file inode).
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Instead of using the i_ztype field in struct zonefs_inode_info to
indicate the zone type of an inode, introduce the new inode flag
ZONEFS_ZONE_CNV to be set in the i_flags field of struct
zonefs_inode_info to identify conventional zones. If this flag is not
set, the zone of an inode is considered to be a sequential zone.
The helpers zonefs_zone_is_cnv(), zonefs_zone_is_seq(),
zonefs_inode_is_cnv() and zonefs_inode_is_seq() are introduced to
simplify testing the zone type of a struct zonefs_inode_info and of a
struct inode.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Simplify zonefs_check_zone_condition() by moving the code that changes
an inode access rights to the new function zonefs_inode_update_mode().
Furthermore, since on mount an inode wpoffset is always zero when
zonefs_check_zone_condition() is called during an inode initialization,
the "mount" boolean argument is not necessary for the readonly zone
case. This argument is thus removed.
zonefs_io_error_cb() is also modified to use the inode offline and
zone state flags instead of checking the device zone condition. The
multiple calls to zonefs_check_zone_condition() are reduced to the first
call on entry, which allows removing the "warn" argument.
zonefs_inode_update_mode() is also used to update an inode access rights
as zonefs_io_error_cb() modifies the inode flags depending on the volume
error handling mode (defined with a mount option). Since an inode mode
change differs for read-only zones between mount time and IO error time,
the flag ZONEFS_ZONE_INIT_MODE is used to differentiate both cases.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Move all code related to zone file operations from super.c to the new
file.c file. Inode and zone management code remains in super.c.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Convert to struct mnt_idmap.
Last cycle we merged the necessary infrastructure in
256c8aed2b ("fs: introduce dedicated idmap type for mounts").
This is just the conversion to struct mnt_idmap.
Currently we still pass around the plain namespace that was attached to a
mount. This is in general pretty convenient but it makes it easy to
conflate namespaces that are relevant on the filesystem with namespaces
that are relevent on the mount level. Especially for non-vfs developers
without detailed knowledge in this area this can be a potential source for
bugs.
Once the conversion to struct mnt_idmap is done all helpers down to the
really low-level helpers will take a struct mnt_idmap argument instead of
two namespace arguments. This way it becomes impossible to conflate the two
eliminating the possibility of any bugs. All of the vfs and all filesystems
only operate on struct mnt_idmap.
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Convert to struct mnt_idmap.
Last cycle we merged the necessary infrastructure in
256c8aed2b ("fs: introduce dedicated idmap type for mounts").
This is just the conversion to struct mnt_idmap.
Currently we still pass around the plain namespace that was attached to a
mount. This is in general pretty convenient but it makes it easy to
conflate namespaces that are relevant on the filesystem with namespaces
that are relevent on the mount level. Especially for non-vfs developers
without detailed knowledge in this area this can be a potential source for
bugs.
Once the conversion to struct mnt_idmap is done all helpers down to the
really low-level helpers will take a struct mnt_idmap argument instead of
two namespace arguments. This way it becomes impossible to conflate the two
eliminating the possibility of any bugs. All of the vfs and all filesystems
only operate on struct mnt_idmap.
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Convert to struct mnt_idmap.
Last cycle we merged the necessary infrastructure in
256c8aed2b ("fs: introduce dedicated idmap type for mounts").
This is just the conversion to struct mnt_idmap.
Currently we still pass around the plain namespace that was attached to a
mount. This is in general pretty convenient but it makes it easy to
conflate namespaces that are relevant on the filesystem with namespaces
that are relevent on the mount level. Especially for non-vfs developers
without detailed knowledge in this area this can be a potential source for
bugs.
Once the conversion to struct mnt_idmap is done all helpers down to the
really low-level helpers will take a struct mnt_idmap argument instead of
two namespace arguments. This way it becomes impossible to conflate the two
eliminating the possibility of any bugs. All of the vfs and all filesystems
only operate on struct mnt_idmap.
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Using REQ_OP_ZONE_APPEND operations for synchronous writes to sequential
files succeeds regardless of the zone write pointer position, as long as
the target zone is not full. This means that if an external (buggy)
application writes to the zone of a sequential file underneath the file
system, subsequent file write() operation will succeed but the file size
will not be correct and the file will contain invalid data written by
another application.
Modify zonefs_file_dio_append() to check the written sector of an append
write (returned in bio->bi_iter.bi_sector) and return -EIO if there is a
mismatch with the file zone wp offset field. This change triggers a call
to zonefs_io_error() and a zone check. Modify zonefs_io_error_cb() to
not expose the unexpected data after the current inode size when the
errors=remount-ro mode is used. Other error modes are correctly handled
already.
Fixes: 02ef12a663 ("zonefs: use REQ_OP_ZONE_APPEND for sync DIO")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
If a file zone transitions to the offline or readonly state from an
active state, we must clear the zone active flag and decrement the
active seq file counter. Do so in zonefs_account_active() using the new
zonefs inode flags ZONEFS_ZONE_OFFLINE and ZONEFS_ZONE_READONLY. These
flags are set if necessary in zonefs_check_zone_condition() based on the
result of report zones operation after an IO error.
Fixes: 87c9ce3ffe ("zonefs: Add active seq file accounting")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
There is a race between modprobe and mount as below:
modprobe zonefs | mount -t zonefs
--------------------------------|-------------------------
zonefs_init |
register_filesystem [1] |
| zonefs_fill_super [2]
zonefs_sysfs_init [3] |
1. register zonefs suceess, then
2. user can mount the zonefs
3. if sysfs initialize failed, the module initialize failed.
Then the mount process maybe some error happened since the module
initialize failed.
Let's register zonefs after all dependency resource ready. And
reorder the dependency resource release in module exit.
Fixes: 9277a6d4fb ("zonefs: Export open zone resource information through sysfs")
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
to_attr() in zonefs sysfs code is unused, which it causes a warning when
compiling with clang and W=1. Delete it to prevent the warning.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
When an IO error occurs, the function __zonefs_io_error() is used to
issue a zone report to obtain the latest zone information from the
device. This function gets a zone report for all zones used as storage
for a file, which is always 1 zone except for files representing
aggregated conventional zones.
The number of zones of a zone report for a file is calculated in
__zonefs_io_error() by doing a bit-shift of the inode i_zone_size field,
which is equal to or larger than the device zone size. However, this
calculation does not take into account that the last zone of a zoned
device may be smaller than the zone size reported by bdev_zone_sectors()
(which is used to set the bit shift size). As a result, if an error
occurs for an IO targetting such last smaller zone, the zone report will
ask for 0 zones, leading to an invalid zone report.
Fix this by using the fact that all files require a 1 zone report,
except if the inode i_zone_size field indicates a zone size larger than
the device zone size. This exception case corresponds to a mount with
aggregated conventional zones.
A check for this exception is added to the file inode initialization
during mount. If an invalid setup is detected, emit an error and fail
the mount (check contributed by Johannes Thumshirn).
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
- Remove iomap_writepage and all callers, since the mm apparently never
called the zonefs or gfs2 writepage functions.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
-----BEGIN PGP SIGNATURE-----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=FuyV
-----END PGP SIGNATURE-----
Merge tag 'iomap-6.0-merge-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull more iomap updates from Darrick Wong:
"In the past 10 days or so I've not heard any ZOMG STOP style
complaints about removing ->writepage support from gfs2 or zonefs, so
here's the pull request removing them (and the underlying fs iomap
support) from the kernel:
- Remove iomap_writepage and all callers, since the mm apparently
never called the zonefs or gfs2 writepage functions"
* tag 'iomap-6.0-merge-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: remove iomap_writepage
zonefs: remove ->writepage
gfs2: remove ->writepage
gfs2: stop using generic_writepages in gfs2_ail1_start_one
A single change for this cycle to simplify handling of the memory page
used as super block buffer during mount (from Fabio).
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSRPv8tYSvhwAzJdzjdoc3SxdoYdgUCYuoYcQAKCRDdoc3SxdoY
dhWYAQDcDZIzcGFrKTpmmpPI9Ep6rCk64V1cIvTKOik+Hp3/8wEA+btduq8w2Wlo
rrCypMOPBIygJxi9h1kugcP41HJLTwo=
=InBn
-----END PGP SIGNATURE-----
Merge tag 'zonefs-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs
Pull zonefs update from Damien Le Moal:
"A single change for this cycle to simplify handling of the memory page
used as super block buffer during mount (from Fabio)"
* tag 'zonefs-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Call page_address() on page acquired with GFP_KERNEL flag
One of the goals is to reduce the overhead of using ->read_iter()
and ->write_iter() instead of ->read()/->write(); new_sync_{read,write}()
has a surprising amount of overhead, in particular inside iocb_flags().
That's why the beginning of the series is in this pile; it's not directly
iov_iter-related, but it's a part of the same work...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCYurGOQAKCRBZ7Krx/gZQ
6ysyAP91lvBfMRepcxpd9kvtuzWkU8A3rfSziZZteEHANB9Q7QEAiPn2a2OjWkcZ
uAyUWfCkHCNx+dSMkEvUgR5okQ0exAM=
=9UCV
-----END PGP SIGNATURE-----
Merge tag 'pull-work.iov_iter-base' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs iov_iter updates from Al Viro:
"Part 1 - isolated cleanups and optimizations.
One of the goals is to reduce the overhead of using ->read_iter() and
->write_iter() instead of ->read()/->write().
new_sync_{read,write}() has a surprising amount of overhead, in
particular inside iocb_flags(). That's the explanation for the
beginning of the series is in this pile; it's not directly
iov_iter-related, but it's a part of the same work..."
* tag 'pull-work.iov_iter-base' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
first_iovec_segment(): just return address
iov_iter: massage calling conventions for first_{iovec,bvec}_segment()
iov_iter: first_{iovec,bvec}_segment() - simplify a bit
iov_iter: lift dealing with maxpages out of first_{iovec,bvec}_segment()
iov_iter_get_pages{,_alloc}(): cap the maxsize with MAX_RW_COUNT
iov_iter_bvec_advance(): don't bother with bvec_iter
copy_page_{to,from}_iter(): switch iovec variants to generic
keep iocb_flags() result cached in struct file
iocb: delay evaluation of IS_SYNC(...) until we want to check IOCB_DSYNC
struct file: use anonymous union member for rcuhead and llist
btrfs: use IOMAP_DIO_NOSYNC
teach iomap_dio_rw() to suppress dsync
No need of likely/unlikely on calls of check_copy_size()
- Fix an accounting bug that made NR_FILE_DIRTY grow without limit
when running xfstests
- Convert more of mpage to use folios
- Remove add_to_page_cache() and add_to_page_cache_locked()
- Convert find_get_pages_range() to filemap_get_folios()
- Improvements to the read_cache_page() family of functions
- Remove a few unnecessary checks of PageError
- Some straightforward filesystem conversions to use folios
- Split PageMovable users out from address_space_operations into their
own movable_operations
- Convert aops->migratepage to aops->migrate_folio
- Remove nobh support (Christoph Hellwig)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEejHryeLBw/spnjHrDpNsjXcpgj4FAmLpViQACgkQDpNsjXcp
gj5pBgf/f3+K7Hi3qw7aYQCYJQ7IA/bLyE/DLWI59kuiao6wDSve40B9YH9X++Ha
mRLp55bkQS+bwS2xa4jlqrIDJzAfNoWlXaXZHUXGL1C/52ChTF6jaH2cvO9PVlDS
7fLv1hy2LwiIdzpKJkUW7T+kcQGj3QLKqtQ4x8zD0LGMg055yvt/qndHSUi41nWT
/58+6W8Sk4vvRgkpeChFzF1lGLy00+FGT8y5V2kM9uRliFQ7XPCwqB2a3e5jbW6z
C1NXQmRnopCrnOT1TFIhK3DyX6MDIWV5qcikNAmCKFb9fQFPmjDLPt9iSoMGjw2M
Z+UVhJCaU3ISccd0DG5Ra/vzs9/O9Q==
=DgUi
-----END PGP SIGNATURE-----
Merge tag 'folio-6.0' of git://git.infradead.org/users/willy/pagecache
Pull folio updates from Matthew Wilcox:
- Fix an accounting bug that made NR_FILE_DIRTY grow without limit
when running xfstests
- Convert more of mpage to use folios
- Remove add_to_page_cache() and add_to_page_cache_locked()
- Convert find_get_pages_range() to filemap_get_folios()
- Improvements to the read_cache_page() family of functions
- Remove a few unnecessary checks of PageError
- Some straightforward filesystem conversions to use folios
- Split PageMovable users out from address_space_operations into
their own movable_operations
- Convert aops->migratepage to aops->migrate_folio
- Remove nobh support (Christoph Hellwig)
* tag 'folio-6.0' of git://git.infradead.org/users/willy/pagecache: (78 commits)
fs: remove the NULL get_block case in mpage_writepages
fs: don't call ->writepage from __mpage_writepage
fs: remove the nobh helpers
jfs: stop using the nobh helper
ext2: remove nobh support
ntfs3: refactor ntfs_writepages
mm/folio-compat: Remove migration compatibility functions
fs: Remove aops->migratepage()
secretmem: Convert to migrate_folio
hugetlb: Convert to migrate_folio
aio: Convert to migrate_folio
f2fs: Convert to filemap_migrate_folio()
ubifs: Convert to filemap_migrate_folio()
btrfs: Convert btrfs_migratepage to migrate_folio
mm/migrate: Add filemap_migrate_folio()
mm/migrate: Convert migrate_page() to migrate_folio()
nfs: Convert to migrate_folio
btrfs: Convert btree_migratepage to migrate_folio
mm/migrate: Convert expected_page_refs() to folio_expected_refs()
mm/migrate: Convert buffer_migrate_page() to buffer_migrate_folio()
...
-----BEGIN PGP SIGNATURE-----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=celk
-----END PGP SIGNATURE-----
Merge tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- Improve the type checking of request flags (Bart)
- Ensure queue mapping for a single queues always picks the right queue
(Bart)
- Sanitize the io priority handling (Jan)
- rq-qos race fix (Jinke)
- Reserved tags handling improvements (John)
- Separate memory alignment from file/disk offset aligment for O_DIRECT
(Keith)
- Add new ublk driver, userspace block driver using io_uring for
communication with the userspace backend (Ming)
- Use try_cmpxchg() to cleanup the code in various spots (Uros)
- Finally remove bdevname() (Christoph)
- Clean up the zoned device handling (Christoph)
- Clean up independent access range support (Christoph)
- Clean up and improve block sysfs handling (Christoph)
- Clean up and improve teardown of block devices.
This turns the usual two step process into something that is simpler
to implement and handle in block drivers (Christoph)
- Clean up chunk size handling (Christoph)
- Misc cleanups and fixes (Bart, Bo, Dan, GuoYong, Jason, Keith, Liu,
Ming, Sebastian, Yang, Ying)
* tag 'for-5.20/block-2022-07-29' of git://git.kernel.dk/linux-block: (178 commits)
ublk_drv: fix double shift bug
ublk_drv: make sure that correct flags(features) returned to userspace
ublk_drv: fix error handling of ublk_add_dev
ublk_drv: fix lockdep warning
block: remove __blk_get_queue
block: call blk_mq_exit_queue from disk_release for never added disks
blk-mq: fix error handling in __blk_mq_alloc_disk
ublk: defer disk allocation
ublk: rewrite ublk_ctrl_get_queue_affinity to not rely on hctx->cpumask
ublk: fold __ublk_create_dev into ublk_ctrl_add_dev
ublk: cleanup ublk_ctrl_uring_cmd
ublk: simplify ublk_ch_open and ublk_ch_release
ublk: remove the empty open and release block device operations
ublk: remove UBLK_IO_F_PREFLUSH
ublk: add a MAINTAINERS entry
block: don't allow the same type rq_qos add more than once
mmc: fix disk/queue leak in case of adding disk failure
ublk_drv: fix an IS_ERR() vs NULL check
ublk: remove UBLK_IO_F_INTEGRITY
ublk_drv: remove unneeded semicolon
...
There is nothing iomap-specific about iomap_migratepage(), and it fits
a pattern used by several other filesystems, so move it to mm/migrate.c,
convert it to be filemap_migrate_folio() and convert the iomap filesystems
to use it.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
->writepage is only used for single page writeback from memory reclaim,
and not called at all for cgroup writeback. Follow the lead of XFS
and remove ->writepage and rely entirely on ->writepages.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Improve static type checking by using the enum req_op type for request
operations.
Reviewed-by: Johannes Thumshirn <jth@kernel.org>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Cc: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-64-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The type name enum req_opf is misleading since it suggests that values of
this type include both an operation type and flags. Since values of this
type represent an operation only, change the type name into enum req_op.
Convert the enum req_op documentation into kernel-doc format. Move a few
definitions such that the enum req_op documentation occurs just above
the enum req_op definition.
The name "req_opf" was introduced by commit ef295ecf09 ("block: better op
and flags encoding").
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220714180729.1065367-2-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
zonefs_read_super() acquires a page with alloc_page(GFP_KERNEL). That
page cannot come from ZONE_HIGHMEM, thus there's no need to map it with
kmap().
Therefore, use a plain page_address() on that page.
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Pass a block_device instead of a request_queue as that is what most
callers have at hand.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20220706070350.1703384-12-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Damien Le Moal