Add the POWER_SUPPLY_PROP_TEMP and a NTC 10K percent VREGN to degrees LUT.
Make sure that a conversion is forced when the power supply is offline so
the temperature is valid.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
PM8226 (used in MSM8226) has v1 smbb hardware and works fine with the
current driver.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The AB8500 charger only has one capacity table with
unspecified temperature, so we assume this capacity is given
for 20 degrees Celsius.
Convert this table to use the OCV (open circuit voltage)
tables in struct power_supply_battery_ocv_table.
In the process, convert the fuel gauge driver to use
microvolts and microamperes so we can use the same internals
as the power supply subsystem without having to multiply
and divide with 1000 in a few places.
Also convert high_curr_threshold and lowbat_threshold to
use microamperes and microvolts as these are closely
related to these changes.
Drop the unused overbat_threshold member in the custom
struct ab8500_fg_parameters.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The lookup from battery temperature to internal resistance was
using its own format. Rewrite this to use the table inside
struct power_supply_battery_info:s resist_table.
The supplied resistance table has to be rewritten to express
the resistance in percent of the factory resistance as a
side effect.
We can then rely on the library function
power_supply_temp2resist_simple() to interpolate the internal
resistance percent from the temperature.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The voltage used in the constant voltage phase of the charging
exist in struct power_supply_battery_info as
constant_charge_voltage_max_uv.
Switch the custom property normal_vol_lvl to this and
consequentially change everything that relates to this value
over to using microvolts rather than millivolts so
we align internal representation of current with the
power core. Prefix every variable we change with *_uv
to indicate the unit everywhere but also to make sure
we do not miss any outlier.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The current used in the constant current phase of the charging
exist in struct power_supply_battery_info as
constant_charge_current_max_ua.
Switch the custom property max_out_curr to this and
consequentally change everything that relates to this value
over to using microamperes rather than milliamperes so
we align internal representation of current with the
power core. Prefix every variable we change with *_ua
to indicate the unit everywhere but also to make sure
we do not miss any outlier.
Drop some duplicate unused defines in a header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The recharge capacity is the hysteresis level for a charger to
restart when a battery does not support maintenance charging.
All products using the AB8500 have batteries supporting
maintenace charging and all code has always set this to 95%.
Turn it into a constant.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The AB8500 custom termination current can be replaced by the
corresponding struct power_supply_battery_info field.
Remove the struct member and amend the code to use the
standard property.
Add *_ua suffix for clarity and to make sure we have
changed all code sites using this member.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The nominal internal resistance isn't used by the AB8500
charging code, instead this resistance is measured continuously,
but we anyways migrate this to the standard property in
struct power_supply_battery_info.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We were assigning some battery data state in probe() but
this is insecure as it depends on the proper probe order
between the components: the charger must probe first so
that the battery data is populated. Move the init to
the bind() call which is certain to happen after the
probe of the master and all components has happened.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The nominal voltage in this charge driver corresponds to
both the voltage_min_design_uv and voltage_max_design_uv
of struct power_supply_battery_info so assign both if this
is undefined.
The overcharge max voltage (when the charger should cut off)
is migrated at the same time so we move both voltages to
struct power_supply_battery_info.
Adjust the code to deal directly with the microvolt values
instead of converting them to millivolts.
Add *_uv suffixes for clarity and to make sure we have
changed all code sites using this member.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The AB8500 custom battery type can be replaced by the
corresponding struct power_supply_battery_info field.
Remove the struct member and amend the code to use the
standard property.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Now that we know that we have only one battery type to
deal with we can proceed to transfer properties to
struct power_supply_battery_info.
The designed capacity for the battery was in a custom field
of the custom battery type in mAh, transfer this to the
standard charge_full_design_uah property in
struct power_supply_battery_info and augment the code
accordingly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The code was going through hoops and loops to detect what
battery is connected and check the resistance for this battery
etc.
Skip this trouble: we will support one battery (currently
"unknown") then we will find the connected battery in the
device tree using a compatible string. The battery resistance
may be used to double-check that the right battery is
connected.
Convert the array of battery types into one battery type so
we can next move over the properties of this one type into
the standard struct power_supply_battery_info.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The code tries to detect a lot of battery variants on the reference
designs, but we are not using the reference designs in practice, we
are using real products such as Samsung Phones.
The reference design with no battery plugged in will be detected as
a LIPO battery with a thermistor on the batctrl pin so we will
assume this and later on we can support other types through the
device tree if we want, just like the products do.
Drop the tables for external thermistor, only keep the internal
thermistor tables that we will use as default.
We can delete the assignment of the temperature to resistance table
since the default will be the only and correct option.
Also get rid of some unused variables and unused exports.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of storing the temperature limits in our custom
struct struct ab8500_bm_data, make struct power_supply_battery_info
a member of this and store the min and max temperatures inside
that struct as the temp_min/temp_max and
temp_alert_min/temp_alert_max respectively.
The values can be assigned from the device tree, but if
not present will be set to the same defaults as are currently
in the code.
This way we start to move over to using
struct power_supply_battery_info and make it possible to move
the data over to the device tree and we will move piece by
piece toward using the standard info struct.
Temperature hysteresis is currently not supported by the
standard struct but we move the assignment here as well so
that we have all parameterization in one spot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The two tables for input and output current translation from
register values does not need to be passed around from the
battery manager data. Just push it down into the charger code
where it is used, like other tables in that code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This deploys the core battery DT parser to read the basic properties
of the battery. We only use very little of it as we start out, but
we will improve as we go along.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The power supply core appears to contain two open coded
linear interpolations. Use the kernel fixpoint arithmetic
interpolation library function instead.
Cc: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for the MAX77976 3.5/5.5A 1-Cell Li+ Battery Charger.
This is a simple implementation enough to be used as a simple battery
charger without OTG and boost.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some chargers can keep the system powered from the mains even when no
battery is present. It this case none of the currently defined health
statuses applies. Add a new status to report that no battery is present.
Suggested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/power/reset/ltc2952-poweroff.c:162:28: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:162:21: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:163:41: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->trigger_delay = ktime_set(2, 500L*1E6L);
^
3 errors generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for floating point values in this driver, as
the values are only assigned to integer types. Use NSEC_PER_MSEC, which
is the same integer value as '1E6L', to avoid changing functionality but
fix the error.
Fixes: 6647156c00 ("power: reset: add LTC2952 poweroff driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: a8083d42b1
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of one shot run of ADC at beginning of charging, run continuous
conversion to ensure that all charging-related values are monitored
properly (input voltage, input current, themperature etc.).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We should not go on looking for more capacity tables after
we realize we have looked at the last one in
power_supply_find_ocv2cap_table().
Fixes: 3afb50d712 ("power: supply: core: Add some helpers to use the battery OCV capacity table")
Cc: Chunyan Zhang <chunyan.zhang@unisoc.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The code doing the initial setting of the F_CONV_RATE field based
on the bq->state.online flag. In order for this to work properly,
this must be done after the initial bq25890_get_chip_state() call.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Before this commit the driver was registering its interrupt handler before
it registered the power_supply, causing bq->charger to potentially be NULL
when the interrupt handler runs, triggering a NULL pointer exception in
the interrupt handler:
[ 21.213531] BUG: kernel NULL pointer dereference, address: 0000000000000680
...
[ 21.213573] Hardware name: Xiaomi Inc Mipad2/Mipad, BIOS MIPad-P4.X64.0043.R03.1603071414 03/07/2016
[ 21.213576] RIP: 0010:__lock_acquire+0x5c5/0x1de0
...
[ 21.213629] Call Trace:
[ 21.213636] ? disable_irq_nosync+0x10/0x10
[ 21.213644] ? __mutex_unlock_slowpath+0x35/0x260
[ 21.213655] lock_acquire+0xb5/0x2b0
[ 21.213661] ? power_supply_changed+0x23/0x90
[ 21.213670] ? disable_irq_nosync+0x10/0x10
[ 21.213676] _raw_spin_lock_irqsave+0x48/0x60
[ 21.213682] ? power_supply_changed+0x23/0x90
[ 21.213687] power_supply_changed+0x23/0x90
[ 21.213697] __bq25890_handle_irq+0x5e/0xe0 [bq25890_charger]
[ 21.213709] bq25890_irq_handler_thread+0x26/0x40 [bq25890_charger]
[ 21.213718] irq_thread_fn+0x20/0x60
...
Fix this by moving the power_supply_register() call to above the
request_threaded_irq() call.
Note this fix includes making the following 2 (necessary) changes:
1. Switch to the devm version of power_supply_register() to avoid the
need to make the error-handling in probe() more complicated.
2. Rename the "irq_fail" label to "err_unregister_usb_notifier" since
the old name no longer makes sense after this fix.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When registering the IRQ handler fails, do not just return the error code,
this will free the devm_kzalloc()-ed data struct while leaving the queued
work queued and the registered power_supply registered with both of them
now pointing to free-ed memory, resulting in various kernel crashes
soon afterwards.
Instead properly tear-down things on IRQ handler register errors.
Fixes: 703df6c097 ("power: bq27xxx_battery: Reorganize I2C into a module")
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add more details to the error messages that indicate what went wrong
and use dev_err_probe() at a few places in the probe() path in order
to avoid error messages for deferred probe after which the driver probes
correctly.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Now that axp288_charger_usb_update_property() reads and caches all
relevant registers, axp288_get_charger_health() can be simplified
by directly returning the health.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Now that axp288_charger_usb_update_property() reads and caches all
relevant registers, the axp288_charger_is_present() and
axp288_charger_is_online() helpers are not necessary anymore.
Directly check the cached input_status instead, allowing the removal
of these 2 helpers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add "depends on IOSF_MBI" to CONFIG_AXP288_CHARGER as the changes from
commit ed22945485 ("power: supply: axp288-charger: Optimize register
reading method") use symbols which are only defined when IOSF_MBI support
is enabled.
Depending on this is ok since IOSF_MBI support should always be enabled
on devices which use the AXP288 PMIC.
Fixes: ed22945485 ("power: supply: axp288-charger: Optimize register reading method")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Look up the battery using the "monitored-battery" phandle
as is nowadays a standard DT binding. The actual bindings
for these charger elements are not upstream so let's sort
out this mess by conforming to the standard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver allocates the mutex but not initialize it.
Use mutex_init() on it to initialize it correctly.
Fixes: ed22945485 ("power: supply: axp288-charger: Optimize register reading method")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
max17042_set_soc_threshold gets called with offset set to 1, which means
that minimum threshold value would underflow once SOC got down to 0,
causing invalid alerts from the gauge.
Fixes: e5f3872d20 ("max17042: Add support for signalling change in SOC")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The gauge requires us to clear the status bits manually for some alerts
to be properly dismissed. Previously the IRQ was configured to react only
on falling edge, which wasn't technically correct (the ALRT line is active
low), but it had a happy side-effect of preventing interrupt storms
on uncleared alerts from happening.
Fixes: 7fbf6b731b ("power: supply: max17042: Do not enforce (incorrect) interrupt trigger type")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently the rt5033_battery driver provides voltage values in mV. It
should be µV as stated in Documentation/power/power_supply_class.rst.
Fixes: b847dd96e6 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The original implementation access the charger the same register value
several times to get the charger status, such as online, enabled, and
bus limits. It takes a long time and bandwidth for every "status get"
operation.
To reduce the access of the register and save bandwidth, this commit
integrated every read operation into only one "register value get"
operation and cache them in the variables. Once the "get properties"
is requested from the user space, the cached information can be returned
immediately.
I2C access between Linux kernel and P-Unit is improved by explicitly taking
semaphore once for the entire set of register accesses in the new
axp288_charger_usb_update_property() function. The I2C-Bus to the XPower
AXP288 is shared between the Linux kernel and SoCs P-Unit. The P-Unit
has a semaphore which the kernel must "lock" before it may use the bus.
If not explicitly taken by the I2C-Driver, then this semaphore is
automatically taken by the I2C-bus-driver for each I2C-transfer. In
other words, the semaphore will be locked and released several times for
entire set of register accesses.
Signed-off-by: Kate Hsuan <hpa@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the function cpcap_battery_probe(), the driver only needs the
data object, so use device_get_match_data() instead, to make the
code cleaner.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Datasheet gives the name IAvg_empty, not LAvg_empty.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On Galaxy S3 (i9300/i9305), which has the max17047 fuel gauge and no
current sense resistor (rsns), the RepSOC register does not provide an
accurate state of charge value. The reported value is wrong, and does
not change over time. VFSOC however, which uses the voltage fuel gauge
to determine the state of charge, always shows an accurate value.
For devices without current sense, VFSOC is already used for the
soc-alert (0x0003 is written to MiscCFG register), so with this change
the source of the alert and the PROP_CAPACITY value match.
Fixes: 359ab9f5b1 ("power_supply: Add MAX17042 Fuel Gauge Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Suggested-by: Wolfgang Wiedmeyer <wolfgit@wiedmeyer.de>
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is a spelling mistake in the name wm831x_battey_apply_config,
fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If CONFIG_THERMAL=n:
drivers/power/supply/power_supply_core.c: In function ‘__power_supply_register’:
drivers/power/supply/power_supply_core.c:1137:6: error: implicit declaration of function ‘psy_has_property’ [-Werror=implicit-function-declaration]
1137 | if (psy_has_property(desc, POWER_SUPPLY_PROP_USB_TYPE) &&
| ^~~~~~~~~~~~~~~~
Fix this by moving psy_has_property() outside the section protected by
CONFIG_THERMAL.
Fixes: 9ba533eb99 ("power: supply: core: Add psy_has_property()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add the helper psy_has_property() to check whether a power supply
has a given property and use it instead of ad hoc iterations over
the property list in multiple locations.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
hrtimer_forward_now() provides the same functionality as the open coded
hrtimer_forward() invocation. Prepares for removal of hrtimer_forward()
from the public interfaces.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reorganize the Kconfig driver description and mention all supported
models. This helps when choosing drivers for given system.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reorganize the Kconfig driver description and mention all supported
models. This helps when choosing drivers for given system.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The power_supply_get_battery_info() fails if device-chemistry property
is missing in a device-tree because error variable is propagated to the
final return of the function, fix it.
Fixes: 4eef766b7d ("power: supply: core: Parse battery chemistry/technology")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There's no need to print a message on every change in battery percentage
on regular log levels.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Prepared by checking the datasheets of max17042, max17047/50
and max170455 for differences in register maps.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This register is same as in MAX17047 and MAX17050, so there's no need
for custom casing it.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
SMB347 can supply power to USB VBUS, implement the USB VBUS regulator.
USB VBUS needs to be powered for switching OTG-cable USB port into host
mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pin control needs to be activated by setting the enable bit, otherwise
hardware rejects all pin changes. Previously this stayed unnoticed on
Nexus 7 because pin control was enabled by default after rebooting from
downstream kernel, which uses driver that enables the bit and charger
registers are non-volatile until power supply (battery) is disconnected.
Configure the pin control enable bit. This fixes the potentially
never-enabled charging on devices that use pin control.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Utilize generic regmap caching in order to avoid unnecessary slow I2C
accesses to all constant registers each time the supply status updated
and remove local caching of charger state to make code cleaner.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The smb347_set_writable() is used by interrupt handler and outside of it.
The interrupt should be disabled when the function is used outside of
interrupt handler in order to prevent racing with the interrupt context.
Add new parameter to smb347_set_writable() that allows to disable IRQ.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The only way to reset the BeagleV Starlight v0.9 board[1] properly is to
tell the PMIC to reset itself which will then assert the external reset
lines of the SoC, USB hub and ethernet phy.
This adds a driver to register a reset handler to do just that.
[1] https://github.com/beagleboard/beaglev-starlight
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
All bits of STATUS register are already defined (see STATUS_SMN_BIT and
further) so there is no need to define status SoC threshold min/max
values one more time.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reading status register can fail in the interrupt handler. In such
case, the regmap_read() will not store anything useful under passed
'val' variable and random stack value will be used to determine type of
interrupt.
Handle the regmap_read() failure to avoid handling interrupt type and
triggering changed power supply event based on random stack value.
Fixes: 39e7213edc ("max17042_battery: Support regmap to access device's registers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This extends the struct power_supply_battery_info with a
"technology" field makes the core DT parser optionally obtain
this from the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This commit introduces support for NETGEAR ReadyNAS Duo v2.
This device use bit 4 of LED[2:0] Polarity Control Register to indicate
AC Power loss.
For more details about AC loss detection in NETGEAR ReadyNAS Duo v2,
please look at the file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This commit prepare driver for another device support.
New power_off_cfg structure describes two most important things: name of
mdio bus and pointer to register setting function. It allow to add new
device with different mdio bus node and other phy register config.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This immutable branch introduces the MT6360 charger driver,
which requires a new linear range helper.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
-----BEGIN PGP SIGNATURE-----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=60NT
-----END PGP SIGNATURE-----
Merge tag 'ib-mt6360-for-5.15-signed' into psy-next
Immutable branch between regulator and power-supply for for 5.15
This immutable branch introduces the MT6360 charger driver,
which requires a new linear range helper.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Rename ChargeOption macros to match the others for ChargeCurrent and
ChargeVoltage and also separate the command & masks macros from the bits of
interest macros for each command. This macro doesn't introduce any
functional change, only code re-org.
Signed-off-by: Bruno Meneguele <bruno.meneguele@smartgreen.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Read voltage_now via IIO and provide the property.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reported-by: kernel test robot <lkp@intel.com> # missing depends on IIO
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add basic support for the battery charger for MT6360 PMIC
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Clean up a handful of checkpatch warnings:
- static const char * array should probably be static const char * const
- function arguments should have identifier names
- else should follow close brace '}'
- suspect code indent for conditional statements
- unnecessary parentheses in an if condition
- avoid multiple line dereference
- remove debug showing function execution, ftrace can trace these better
- prefer 'long' over 'long int' as the int is unnecessary
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use the defined variable "dev" to make the code cleaner.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
As defined by the Smart Battery Data Specification.
An _AVG suffix is added to the enum values REG_TIME_TO_EMPTY and
REG_TIME_TO_FULL to make the distinction clear.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The Smart Battery Data Specification allows for values 0..65535 mV,
there is no reason to limit the value to 20000.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the probe function, when get irq failed, the function
platform_get_irq_byname() logs an error message, so remove
redundant message here.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
MAX77849 is a combined fuel-gauge, charger and MUIC IC. Notably,
fuel-gauge has dedicated i2c lines and seems to be fully compatible
with max17047. Add new compatible for it reusing max17047 code paths.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. If not explicitly taken by the I2C-driver,
then this semaphore is automatically taken by the I2C-bus-driver for
each I2C-transfer and this is a quite expensive operation.
Explicitly take the semaphore in probe() around the register-accesses
done during probe, so that this only needs to be done once, rather then
once per register-access.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. If not explicitly taken by the I2C-driver,
then this semaphore is automatically taken by the I2C-bus-driver for
each I2C-transfer.
Move the AXP20X_CC_CTRL check done in probe() together with the other
register-accesses done in probe, so that we can take the semaphore once
for the entire set of register-accesses.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus and while the kernel holds the semaphore the CPU
and GPU power-states must not be changed otherwise the system will freeze.
This is a complex process, which is quite expensive. This is all done by
iosf_mbi_block_punit_i2c_access(). To ensure that no unguarded I2C-bus
accesses happen, iosf_mbi_block_punit_i2c_access() gets called by the
I2C-bus-driver for every I2C transfer. Because this is so expensive it
is allowed to call iosf_mbi_block_punit_i2c_access() in a nested
fashion, so that higher-level code which does multiple I2C-transfers can
call it once for a group of transfers, turning the calls done by the
I2C-bus-driver into no-ops.
Userspace power-supply API users typically will read all provided
properties in one go, refreshing the last read values when
power_supply_changed() is called by the driver and/or periodically
(e.g. every 2 minutes).
The reading of all properties in one go causes the P-Unit semaphore
to quickly be taken and released multiple times in a row. Certain
PMIC registers like AXP20X_FG_RES are even used in multiple properties
so they get read multiple times, leading to a P-Unit take + release
each time the register is read.
As already mentioned the taking of the P-Unit semaphore is a quite
expensive operation and it has also been reported that the
"hammering" of the P-Unit semaphore done by the axp288_fuel_gauge
driver can even cause stability issues with the system as a whole.
Switch over to a scheme where the axp288_fuel_gauge driver keeps
a local copy of all the registers which it uses for properties
and make it only refresh its copy of the registers if the values
are older then 1 minute; or when a fuel-gauge interrupt has
triggered since the last read.
This not only reduces the amount of reads, it also makes the code
do all the reads in one go, rather then reading specific registers
based on which property is being queried. This allows calling
iosf_mbi_block_punit_i2c_access() once before doing all the reads,
so that we now only take the P-Unit semaphore once per update.
Tested-by: Andrejus Basovas <cpp@gcc.lt>
Signed-off-by: Andrejus Basovas <cpp@gcc.lt>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Accessing registers on the AXP288 is quite expensive, so we should avoid
doing unnecessary accesses.
The FG_LOW_CAP_REG never changes underneath us, so we only need to read
it once. Devices with an AXP288 do not have user-replace (let alone
hot-swappable) batteries and the only bit we care about in the
PWR_OP_MODE register is the CHRG_STAT_BAT_PRESENT bit, so we can get
away with only reading the PWR_OP_MODE register once too.
Note that the FG_LOW_CAP_REG is not marked volatile in the regmap, so we
were effectively already reading it once. This change makes this explicit,
this is done as preparation of a further patch which moves all remaining
register accesses in fuel_gauge_get_property() out of that function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Directly store the struct device pointer in axp288_fg_info, rather then
storing a pointer to the struct platform_device there and then using
"&info->pdev->dev" everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The I2C-bus to the XPower AXP288 is shared between the Linux kernel and
the SoCs P-Unit. The P-Unit has a semaphore which the kernel must "lock"
before it may use the bus. This semaphore is automatically taken by the
I2C-bus-driver.
The retry on -EBUSY logic in fuel_gauge_reg_readb() likely was added to
deal with the I2C-bus-drive returning -EBUSY when it failed to take the
semaphore, but this really should never happen. The semaphore code even
has a WARN_ON(ret) to log a kernel backtrace if this does somehow happen,
when this happens something is seriously wrong and the system typically
freezes soon afterwards.
TL;DR: the regmap_read() should never fail with -EBUSY so the retries
are unnecessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When fuel_gauge_reg_readb()/_writeb() fails, report which register we
were trying to read / write when the error happened.
Also reword the message a bit:
- Drop the axp288 prefix, dev_err() already prints this
- Switch from telegram / abbreviated style to a normal sentence, aligning
the message with those from fuel_gauge_read_*bit_word()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Drop the IRQ mapping messages, because they are really not
interesting at all.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The debugfs code is simply just dumping a bunch of registers, the same
information can also easily be gotten through the regmap debugfs
interface or through the i2cdump utility.
I've not used the debugfs interface once in all these years that I've
been working on the axp288_fuel_gauge driver, so lets just remove it.
Note this also removes the temperature-channels from the list of
IIO ADC channels used by the driver, since these were only used in the
debugfs interface.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The values of various defines used in the driver are not aligned
properly when tabsize is set to 8 (I guess they were created with
a different tabsize).
Properly align the defines to make the code easier to read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In the function sc27xx_fgu_probe(), when get irq failed,
platform_get_irq() logs an error message, so remove
redundant message here.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Deal with deferred probe using dev_err_probe so the error is handled
and avoid logging lots probe defer information like the following:
[ 9.125121] cw2015 4-0062: Failed to register power supply
[ 9.211131] cw2015 4-0062: Failed to register power supply
Fixes: b4c7715c10 ("power: supply: add CellWise cw2015 fuel gauge driver")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds a driver for PCHG (Peripheral CHarGer). PCHG is a
framework managing power supplies for peripheral devices.
This driver creates a sysfs node for each peripheral charge port:
/sys/class/power_supply/peripheral<n>
where <n> is the index of a charge port.
For example, when a stylus is connected to a NFC/WLC port, the node
returns:
/sys/class/power_supply/peripheral0/
capacity=50
charge_type=Standard
scope=Device
status=Charging
type=Battery
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This file isn't using any AB8500 symbols so drop these includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If we rename the "abx500_chargalg" supply to "ab8500_chargalg"
as it should be named, the existing supplies are supplying that
supply but that was obviously not working since it had the
wrong name.
Now that the dependency kicks in we get a bunch
of NULL references from ab8500_chargalg_external_power_changed()
so check that the workqueue is allocated before we try to
queue work on it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Drop the entire idea with abx500 being abstract and different from ab8500
in the AB8500 charging drivers. This rids the two identical definitions
of a slew of structs in ab8500-bm.h and makes things less confusion and
easier to understand.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The "abx500" name on the charging algorithm stems from the ambition
to produce a series of these analog basebands, re-using the same
charging algorithm driver. No ASICs beside AB8500 and AB8505 were
ever produced so this terminology is confusing. Rename the
algorithm file and symbols to reflect the more narrow scope.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The kernel already has a static inline for linear interpolation
so use that instead of rolling our own.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
kernel.h is being used as a dump for all kinds of stuff for a long time.
Here is the attempt to start cleaning it up by splitting out panic and
oops helpers.
There are several purposes of doing this:
- dropping dependency in bug.h
- dropping a loop by moving out panic_notifier.h
- unload kernel.h from something which has its own domain
At the same time convert users tree-wide to use new headers, although for
the time being include new header back to kernel.h to avoid twisted
indirected includes for existing users.
[akpm@linux-foundation.org: thread_info.h needs limits.h]
[andriy.shevchenko@linux.intel.com: ia64 fix]
Link: https://lkml.kernel.org/r/20210520130557.55277-1-andriy.shevchenko@linux.intel.com
Link: https://lkml.kernel.org/r/20210511074137.33666-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Helge Deller <deller@gmx.de> # parisc
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trying to get the AB8500 charging driver working I ran into a bit
of bitrot: we haven't used the driver for a while so errors in
refactorings won't be noticed.
This one is pretty self evident: use argument to the macro or we
end up with a random pointer to something else.
Cc: stable@vger.kernel.org
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Marcus Cooper <codekipper@gmail.com>
Fixes: 297d716f62 ("power_supply: Change ownership from driver to core")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The continue statement at the end of a for-loop has no effect,
invert the if expression and remove the continue.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
It turns out that the "T3 MRD" DMI_BOARD_NAME value is used in a lot of
different Cherry Trail x5-z8300 / x5-z8350 based Mini-PC / HDMI-stick
models from Ace PC / Meegopad / MinisForum / Wintel (and likely also
other vendors).
Most of the other DMI strings on these boxes unfortunately contain various
generic values like "Default string" or "$(DEFAULT_STRING)", so we cannot
match on them. These devices do have their chassis-type correctly set to a
value of "3" (desktop) which is a pleasant surprise, so also match on that.
This should avoid the quirk accidentally also getting applied to laptops /
tablets (which do actually have a battery). Although in my quite large
database of Bay and Cherry Trail based devices DMIdecode dumps I don't
have any laptops / tables with a board-name of "T3 MRD", so this should
not be an issue.
BugLink: https://askubuntu.com/questions/1206714/how-can-a-mini-pc-be-stopped-from-being-detected-as-a-laptop-with-a-battery/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
As documented in the updated "Naming" chapter of
Documentation/process/coding-style.rst, usage of the work blacklist
should be avoided where possible.
Rename the list of devices which have no battery to the
axp288_no_battery_list, which also more accurately describes the
contents of the list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr() does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF):
drivers/power/supply/bq24190_charger.c:1972:34: warning: ‘bq24190_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Signed-off-by: Yu Jiahua <yujiahua1@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This avoids reimplementing the detection logic twice and removes the
possibility of activating charging with 500mA even if a battery is not
detected.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This invalidates empty->counter_uah and charge_full when charge_now
indicates that they are grossly wrong and adds some tolerance to
POWER_SUPPLY_PROP_CHARGE_FULL to allow for inaccuracies in the charge
counter and manufacturing tolerances in the battery.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Allow disabling and re-enabling battery charging of an axp209 PMIC
through a writable status property. With the current driver code
charging is always on.
This works on the axp209 of Banana {Pi M1+,Pro} and should work on all
AXP chips.
Signed-off-by: Hermann.Lauer@uni-heidelberg.de
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are no platforms using the driver with platform data (no board
files with the driver), so the dead code can be dropped.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver was reporting POWER_SUPPLY_PROP_ONLINE via platform data
functions or '1' if no platform data was provided. Since there are no
platforms using the driver with platform data (no board files with the
driver), the online property can be simplified to always return '1'.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver was reporting POWER_SUPPLY_PROP_STATUS via platform data
functions. Without platform data, the max17040_get_status() functions
returns early with POWER_SUPPLY_STATUS_UNKNOWN. Since there are no
platforms using the driver with platform data (no board files with the
driver), the status property was always unknown.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The fuel gauge in the RT5033 PMIC has its own I2C bus and interrupt
line. Therefore, it is not actually part of the RT5033 MFD and needs
its own of_match_table to probe properly.
Also, given that it's independent of the MFD, there is actually
no need to make the Kconfig depend on MFD_RT5033. Although the driver
uses the shared <linux/mfd/rt5033.h> header, there is no compile
or runtime dependency on the RT5033 MFD driver.
Cc: Beomho Seo <beomho.seo@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Fixes: b847dd96e6 ("power: rt5033_battery: Add RT5033 Fuel gauge device driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The only known BD70528 use-cases are such that the PMIC is controlled
from separate MCU which is not running Linux. I am not aware of
any Linux driver users. Furthermore, it seems there is no demand for
this IC. Let's ease the maintenance burden and drop the driver. We can
always add it back if there is sudden need for it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 14577/77836 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Iskren Chernev <iskren.chernev@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 17047/77693 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The ac->state field is __le32, not u32. So change the variable we're
temporarily storing it in to __le32 as well.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e61ffb3445 ("power: supply: Add AC driver for Surface Aggregator Module")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently sbs-battery supports three string properties -
manufacturer, model_name, and chemistry. Buffers for those
properties are currently defined as global variables.
This patch moves those global variables into struct sbs_info
and cache/reuse them as they are all constant values.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adds properties for setting the maximum current to USB, ADP and Battery
supplies. USB and ADP limits are reset to OTP values upon replugging.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The RC5T619 can detect SDP, CDP and DCP chargers, so let's add support
for it.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver is including the legacy GPIO header <linux/gpio.h>
but not using any symbols from it. Delete the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The PM2301 was only used in tandem with AB9540, part of U9540,
a platform that was cancelled and never deployed in products.
Delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The result of container_of() operations is never NULL unless the element
is the first element of the embedded structure, which is not the case here.
The NULL check is therefore unnecessary and misleading. Remove it.
This change was made automatically with the following Coccinelle script.
@@
type t;
identifier v;
statement s;
@@
<+...
(
t v = container_of(...);
|
v = container_of(...);
)
...
when != v
- if (\( !v \| v == NULL \) ) s
...+>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This setting is read directly from the device tree in
the ab8500_charger.c code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The vendor code tree supplies platform data to enable he
USB charging for AB8500 and AB8500 and disable the AC
charging on the AB8505. This was missed when the driver
was submitted to the mainline kernel.
Fix this by doing what the vendor kernel does: always
register the USB charger, do not register the AC charger
on the AB8505.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Sometimes the code will crash because we haven't enabled
AC or USB charging and thus not created the corresponding
psy device. Fix it by checking that it is there before
notifying.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The code was calling ab8500_bm_of_probe() in four different
spots effectively overwriting the same configuration three
times. This was done because probe order was uncertain.
Since we now used componentized probe, call it only once
while probing the main charging component.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver has problems with the different components of
the charging code racing with each other to probe().
This results in all four subdrivers populating battery
information to ascertain that it is populated for their
own needs for example.
Fix this by using component probing and thus expressing
to the kernel that these are dependent components.
The probes can happen in any order and will only acquire
resources such as state container, regulators and
interrupts and initialize the data structures, but no
execution happens until the .bind() callback is called.
The charging driver is the main component and binds
first, then bind in order the three subcomponents:
ab8500-fg, ab8500-btemp and ab8500-chargalg.
Do some housekeeping while we are moving the code around.
Like use devm_* for IRQs so as to cut down on some
boilerplate.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The battery subsystem of the Surface Aggregator Module EC requires us to
register the battery notifier with instance ID 0. However, battery
events are actually sent with the instance ID corresponding to the
device, which is nonzero. Thus, the strict-matching approach doesn't
work here and will discard events that the driver is expected to handle.
To fix this we have to fall back on notifier matching by target-category
only and have to manually check the instance ID in the notifier
callback.
Fixes: 167f77f7d0 ("power: supply: Add battery driver for Surface Aggregator Module")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
battery/charger driver changes:
* core: provide function stubs if CONFIG_POWER_SUPPLY=n
* core: reduce loglevel for probe defer info
* surface-battery: new battery driver for Surface
* surface-charger: new charger driver for Surface
* bq27xxx: add bq78z100 support
* bq27xxx: fix current_now/power_avg for newer chips
* cw2015: add CHARGE_NOW support
* ab8500: drop pdata support
* convert most DT bindings to YAML
* lot's of minor fixes and cleanups
reset drivers:
* ltc2952-poweroff: make trigger delay configurable from DT
* minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=9IUN
-----END PGP SIGNATURE-----
Merge tag 'for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"battery/charger driver changes:
- core:
- provide function stubs if CONFIG_POWER_SUPPLY=n
- reduce loglevel for probe defer info
- surface:
- new battery and charger drivers for Surface
- bq27xxx:
- add bq78z100 support
- fix current_now/power_avg for newer chips
- cw2015:
- add CHARGE_NOW support
- ab8500:
- drop pdata support
- convert most DT bindings to YAML
- lots of minor fixes and cleanups
reset drivers:
- ltc2952-poweroff:
- make trigger delay configurable from DT
- minor fixes and cleanups"
* tag 'for-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (97 commits)
power: supply: cpcap-battery: fix invalid usage of list cursor
power: supply: bq256xx: add kerneldoc for structure members
power: supply: act8945a: correct kerneldoc
power: supply: max17040: remove unneeded double cast
power: supply: max17040: handle device_property_read_u8_array() failure
power: supply: max14577: remove unneeded variable initialization
power: supply: surface-charger: Make symbol 'surface_ac_pm_ops' static
power: supply: surface-battery: Make some symbols static
power: reset: restart-poweroff: Add missing MODULE_DEVICE_TABLE
power: reset: hisi-reboot: add missing MODULE_DEVICE_TABLE
power: supply: s3c_adc_battery: fix possible use-after-free in s3c_adc_bat_remove()
power: supply: generic-adc-battery: fix possible use-after-free in gab_remove()
power: supply: Add AC driver for Surface Aggregator Module
power: supply: Add battery driver for Surface Aggregator Module
power: supply: bq25980: Move props from battery node
power: supply: core: Use true and false for bool variable
power: supply: goldfish: Remove the GOLDFISH dependency
power: reset: ltc2952: make trigger delay configurable
power: supply: cpcap-charger: Simplify bool conversion
power: supply: cpcap-charger: Add usleep to cpcap charger to avoid usb plug bounce
...
Fix invalid usage of a list_for_each_entry in cpcap_battery_irq_thread().
Empty list or fully traversed list points to list head, which is not
NULL (and before the first element containing real data).
Signed-off-by: Guangqing Zhu <zhuguangqing83@gmail.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Carl Philipp Klemm <philipp@uvos.xyz>
Tested-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Document members of structure to fix W=1 warnings like:
drivers/power/supply/bq256xx_charger.c:240: warning:
Function parameter or member 'charger' not described in 'bq256xx_device'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove incorrect kerneldoc marker to fix W=1 warning:
drivers/power/supply/act8945a_charger.c:22: warning:
This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There is no need for double explicit cast from of_device_get_match_data()
(uintptr_t and then to target enum) because implicit conversion from
uintptr_t to enum is straightforward (uintptr_t is a integer type).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The device_property_read_u8_array() call should not fail because it is
preceded with device_property_count_u8() and check for number of
readable u8 values. However the code is more obvious and easier to read
if the return value of device_property_read_u8_array() is checked.
Otherwise reader needs to investigate whether really there is no risk of
using random stack values of 'rcomp' variable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The local 'current_bits' variable does not have to be initialized
because all cases in following switch() either return or initialize it.
Addresses-Coverity: Unused value
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The sparse tool complains as follows:
drivers/power/supply/surface_charger.c:229:1: warning:
symbol 'surface_ac_pm_ops' was not declared. Should it be static?
This symbol is not used outside of surface_charger.c, so this
commit marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The sparse tool complains as follows:
drivers/power/supply/surface_battery.c:700:1: warning:
symbol 'dev_attr_alarm' was not declared. Should it be static?
drivers/power/supply/surface_battery.c:805:1: warning:
symbol 'surface_battery_pm_ops' was not declared. Should it be static?
This symbol is not used outside of surface_battery.c, so this
commit marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Lifu <chenlifu@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On newer Microsoft Surface models (specifically 7th-generation, i.e.
Surface Pro 7, Surface Book 3, Surface Laptop 3, and Surface Laptop Go),
battery and AC status/information is no longer handled via standard ACPI
devices, but instead directly via the Surface System Aggregator Module
(SSAM), i.e. the embedded controller on those devices.
While on previous generation models, AC status is also handled via SSAM,
an ACPI shim was present to translate the standard ACPI AC interface to
SSAM requests. The SSAM interface itself, which is modeled closely after
the ACPI interface, has not changed.
This commit introduces a new SSAM client device driver to support AC
status/information via the aforementioned interface on said Surface
models.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On newer Microsoft Surface models (specifically 7th-generation, i.e.
Surface Pro 7, Surface Book 3, Surface Laptop 3, and Surface Laptop Go),
battery and AC status/information is no longer handled via standard ACPI
devices, but instead directly via the Surface System Aggregator Module
(SSAM), i.e. the embedded controller on those devices.
While on previous generation models, battery status is also handled via
SSAM, an ACPI shim was present to translate the standard ACPI battery
interface to SSAM requests. The SSAM interface itself, which is modeled
closely after the ACPI interface, has not changed.
This commit introduces a new SSAM client device driver to support
battery status/information via the aforementioned interface on said
Surface models. It is in parts based on the standard ACPI battery
driver.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT and
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE are exposed on
the battery node and this is incorrect.
This patch exposes both of them on the charger node rather
than the battery node.
Fixes: 5069185fc1 ("power: supply: bq25980: Add support for the BQ259xx family")
Signed-off-by: Ricardo Rivera-Matos <r-rivera-matos@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=+5eM
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-power-v5.13' into psy-next
Immutable branch between MFD and Power due for the v5.13 merge window.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
