The cx18 can support transport streams with newer firmwares. Add a TS
capability to the generic cx2341x module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Completely rely on the video_ioctl2 debugging facilities rather than
doing it ourselves.
Fill in some missing fields in ivtv with VIDIOC_G_FBUF.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Various ioctl debugging fixes and improvements:
- use %x rather than %d for control IDs and bitmask fields
- make two arrays const
- show the whole control array for the ext_ctrl ioctls
- print pix_fmt for V4L2_BUF_TYPE_VIDEO_OUTPUT
- show full type name rather than an integer
- fix CROPCAP debugging
- fix G/S_TUNER debugging
- show error code in case of an error
- other small cleanups
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The xc5000 firmware download process can be slow on certain devices.
Add a module option, "init_fw" to perform the firmware download during
xc5000_attach(), which would get the firmware download over with well
before any tune request is made.
When this option is enabled, it will reduce the time it takes to get a
signal lock during the first tune after driver load, but will add a few
seconds to the driver initialization.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IVTV_IOC_DMA_FRAME ioctl fails to correctly 'start' the decoder. Although
yuv output will be correct, some functions which should be disabled while the
decoder is in use remain enabled. This can result in hardware registers being
corrupted, causing problems with the mpeg decoder. This patch ensures the
decoder 'start' sequence is called, disabling these functions until the
device is closed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
write() operations to the yuv device may not always 'start' the decoder.
Although yuv output will be correct, some functions which should be disabled
while the decoder is in use remain enabled. This can result in hardware
registers being corrupted, causing problems with the mpeg decoder. This patch
simply moves the existing decoder 'start' sequence to earlier in the write()
handler.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the capture is scaled, then the video_temporal_filter is set to 0
by the cx2341x.c module since otherwise you would get ghosting.
However, this was also done in the VIDIOC_S_FMT ioctl which meant that
the video_temporal_filter control was reset to 0 or 8 each time S_FMT
was called. This was old code that should have been removed a long time
ago.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This avoids the need of memsets in the ivtv/cx18 drivers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: convert driver to use video_ioctl2(). Pushed down ioctl debug
messages and priority checks as well. Still left serialization lock in
place for now. #if 0'ed out sliced vbi ioctl code for now.
Patch heavily based on similar changes made to ivtv by Hans Verkuil.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Based on an initial conversion patch from Douglas Landgraf.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A number of V4L drivers have a mod param to specify their preferred minors.
This is because it is often desirable for applications to have a static /dev
name for a particular device. However, using minors has several disadvantages:
1) the requested minor may already be taken
2) using a mod param is driver specific
3) it requires every driver to add a param
4) requires configuration by hand
This patch introduces an "index" attribute that when combined with udev rules
can create static device paths like this:
/dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video0
/dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video1
/dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video2
$ ls -la /dev/v4l/by-path/pci-0000\:00\:1d.2-usb-0\:1\:1.0-video0
lrwxrwxrwx 1 root root 12 2008-04-28 00:02 /dev/v4l/by-path/pci-0000:00:1d.2-usb-0:1:1.0-video0 -> ../../video1
These paths are steady across reboots and should be resistant to rearranging
across Kernel versions.
video_register_device_index is available to drivers to request a
specific index number.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Kees Cook <kees@outflux.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support the bundled remote control of the TT DVB-C 1501
Thanks-to: SG <SiestaGomez@web.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed some obsolete definitions and one unused variable.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The build option, MEDIA_TUNER_CUSTOMIZE, allows us to disable tuner drivers
that would have otherwise been selected by default. This is an advanced
customization option that should be disabled by default.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Auto-selects tda10023, for budget-ci, if !DVB_FE_CUSTOMISE. This is needed for
Technotrend budget C-1501 dvb board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following experimental patch adds support for the technotrend budget
C-1501 dvb-c card. The parameters used to configure the tda10023 demod
chip are largely determined experimentally, but works quite for me in my
initial tests.
Signed-off-by: Sigmund Augdal <sigmund@snap.tv>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up the use of structure templates in bttv-i2c. For one thing, a
real template is supposed to be read-only. And in some cases it's more
efficient to initialize the few fields we need individually.
This clean-up shrinks bttv-i2c.o by 29% (x86_64).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up the use of structure templates in zoran_card. For one thing,
a real template is supposed to be read-only. And in some cases it's
more efficient to initialize the few fields we need individually.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- support for Anysee E30C Plus rev 0.4
- set IO port E
- set correct TS mode
- change deltaf according to latest Windows driver
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Split the Beholder M6 family to different models. Because M6 hasn`t RDS, M63
has chip with AC3 codec, M6 Extra has other type of HF module.
Add correct data for support MPEG encoder.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rework saa7134_enable_i2s function. Remove vendor specific data.
Configure I2S output port specific for model of SAA7133/5-SAA7134.
I think it is more good.
Renamed definition of I2S audio output control register. It`s SAA7133/5 register
Start video port after configuring procedure.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Separate the newer variant of the HVR-900 into its own device profile
because it has a Micronas DRX397 instead of the Zarlink demod. This
doesn't make the device work, but at least we don't try to initialize it
as though it had the Zarlink device.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
[mchehab@infradead.org: avoid compilation breakage at mainstream, where drx397xD.h doesn't exist yet]
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- this now finally adds hardware frequency seek support
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- afc indication:
device has no indication whether freq is too low or too high
therefore afc always return 1, when freq is wrong
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- comment on how to listen to an usb audio device
(i get so many questions about that...)
- code cleanup (error handling, more warnings, spacing, ...)
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch brings the following changes:
- version bumped to 1.0.8 for all the following patches
- si470x_get_freq now returns errno
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
this patch brings the following changes:
- move the global disconnect lock into the device structure
- code cleanup (spaces to tabs, long line splits, ...)
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only one frontend is enabled right now. The second frontend can lock,
but transport doesn't work yet. The device will be supported as a
single tuner device until the second frontend is working.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This file was renamed but we forgot to change it in the comments.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- update license comments
- change MODULE_DESCRIPTION from device specific to chipset specific
- correct debug switch from deb_rc to deb_info
- correct MPEG2 stream interval from 1.25 to 1
- change frontend_attach error code from -EIO to -ENODEV
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The naming for the callbacks that handle the VIDIOC_ENUM_FMT and
VIDIOC_S/G/TRY_FMT ioctls was very confusing. Renamed it to match
the v4l2_buf_type name.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There was no vidioc_try_fmt_sliced_vbi_output, instead vidioc_try_fmt_vbi_output
was reused.
The VIDIOC_ENUMOUTPUT handling was missing altogether, even though the callback
existed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default videodev behavior for VIDIOC_G_STD is not correct for all devices.
Add a new callback that drivers can use instead.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__video_do_ioctl incorrectly zeroed the tuner field of v4l2_frequency and
did not zero the full fmt union of v4l2_format.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Back in the early days of the pvrusb2 driver, the kernel class
mechanism in use for the sysfs interface had no means to pass
per-attribute information to the show / store functions. This forced
me to implement a horrible ugly thunking mechanism (i.e. infer the
missing data through the use of dedicated cookie cutter bounce
functions). However now we're using a better mechanism which also
passes enough additional information to the show / store functions
that we no longer need the hack. So eliminate all the crap. Yay!
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver enforces a "quiet period" on the encoder in certain
situations before attempting to operate it. This seems to help avoid
video encoding errors / corruption. The quiet period was 50msec, but
through experimentation it has been observed to improve further if the
interval is increased to 100msec.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is primarily a cosmetic change to make it easier to change some
of the time constants used in the driver.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Separate gpio_init field and xceive_pin and combine the two when
the gpio is initialized. So there is no longer any need to set the
xceive pin in the gpio_init values, simplifying the creation of a
new card definition.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Peter Brandt for doing the necessary tests to fill out the card
definition!
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
snprinf() takes the trailing \0 into account in its length calculations,
so there is no need to subtract 1 to the buffer size.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add invertation of image mirroring register bits to default
configuration.
This is useful when the camera module is e.g. mounted upside down.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
write() operations to the ivtv framebuffer will now attempt to use DMA if the
amount of data to copy is >= 4096 bytes. This change effectively depreciates
the need for the proprietary IVTVFB_IOC_DMA_FRAME ioctl since a write() of
sufficient size will do the same thing.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver initially sets the tuner to known broadcast frequencies
in the Chicago area, to ease driver testing for the maintainer.
This patch keeps those default frequencies, but allows them to be altered
via modprobe option. This allows the same ease and convenience for testing
multiple pvrusb2 devices one after another under other conditions and areas.
For instance, the default initial frequency, 175.25 MHz, might not
necessarily be valid on all cable television networks, but usually will be a
valid NTSC broadcast channel.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_addr_{lock,unlock}{,_bh}() helpers.
Use them to protect operations that operate on or read
the network device unicast and multicast address lists.
Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-2.6.27' of git://git.infradead.org/users/dwmw2/firmware-2.6: (64 commits)
firmware: convert sb16_csp driver to use firmware loader exclusively
dsp56k: use request_firmware
edgeport-ti: use request_firmware()
edgeport: use request_firmware()
vicam: use request_firmware()
dabusb: use request_firmware()
cpia2: use request_firmware()
ip2: use request_firmware()
firmware: convert Ambassador ATM driver to request_firmware()
whiteheat: use request_firmware()
ti_usb_3410_5052: use request_firmware()
emi62: use request_firmware()
emi26: use request_firmware()
keyspan_pda: use request_firmware()
keyspan: use request_firmware()
ttusb-budget: use request_firmware()
kaweth: use request_firmware()
smctr: use request_firmware()
firmware: convert ymfpci driver to use firmware loader exclusively
firmware: convert maestro3 driver to use firmware loader exclusively
...
Fix up trivial conflicts with BKL removal in drivers/char/dsp56k.c and
drivers/char/ip2/ip2main.c manually.
Although it wasn't actually using ihex records before, we use the Intel
HEX record format for this firmware -- because that gives us a simple
way to split it into separate chunks internally as we need, without
loading each part as a separate file.
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cortland Setlow pointed out a bug in ov7670.c where the result from
ov7670_read() was just being checked for !0, rather than <0. This made me
realize that ov7670_read's semantics were rather confusing; it both fills
in 'value' with the result, and returns it. This is goes against general
kernel convention; so rather than fixing callers, let's fix the function.
This makes ov7670_read return <0 in the case of an error, and 0 upon
success. Thus, code like:
res = ov7670_read(...);
if (!res)
goto error;
..will work properly.
Signed-off-by: Cortland Setlow <csetlow@tower-research.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a const pointer to non-const pointer assignment error in the Conexant
cx23418 MPEG encoder driver.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
...which means allocating our own copy when we want to modify it.
(stupid thinko fixed by mkrufky)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
UVC makefile defines obj as:
obj-$(CONFIG_USB_VIDEO_CLASS) := uvcvideo.o
Instead of:
obj-$(CONFIG_USB_VIDEO_CLASS) += uvcvideo.o
Due to that, if uvc is selected, all obj-y or obj-m that were added to
compilation were forget. This breaks a proper kernel build.
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This driver supports video input devices compliant with the USB Video Class
specification. This means lots of currently manufactured webcams, and probably
most of the future ones.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134 driver uses a (non-atomic) variable in an attempt to
only allow one opener of the device (how it deals with sending
the fd over unix sockets I don't know).
Unfortunately, the release function first decrements this variable,
and THEN goes on to disable more of the device. This allows for
a race where another opener of the device comes in after the decrement of
the variable, configures the hardware just to then see the hardware
be disabled by the rest of the release function.
This patch makes the release function use the same lock as the open
function to protect the hardware as well as the variable (which now
at least has some locking to protect it).
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move allocation after first check and fix memory leak.
Noticed-by: Daniel Marjamäki <danielm77@spray.se>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch ensures that the xc5000 will have firmware loaded as needed if the
part is powered down or reset via gpio from the host. An example of this, in
some cases, could be after the system resumes from standby or hibernate modes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This decreases scan time in Queens, New York from 28 minutes to 7 minutes,
with the exact same services found.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDIOC_ENUMSTD did not return all the PAL/SECAM/NTSC variants: it just returned
one single PAL/SECAM/NTSC standard without separate entries for the trickier
standards like NTSC-JP.
Changed the code so that it behaves better.
Also simplified the if/switch statements into a common standards lookup table.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix uncorrected block counter and bit error rate to follow DVB API spec:
- Unsupported controls return -ENOSYS.
- UNC must never be set to 0.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the i2c write fails during initialisation, an oops happens
because state->frontend.dvb is still undefined. Fixed.
Thanks to Sigmund Augdal for reporting this bug,
and to Hartmut Birr for suggesting the fix.
Thanks-to: Sigmund Augdal <sigmund@snap.tv>
Thanks-to: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Fix S-Video and Compsite input settings for the Yuan MPC718 per user
reports from Yuri Warczynski <Yuri.Warczynski@gmail.com> and
Brian Hope <brian@hopefamily.info> and enable the card entry. The tuner reset
GPIO pin is likely incorrect as the tuner firmware cannot be reloaded without a
reboot. It is likely the audio routing is done via GPIO which is not
implemented yet, as users report audio doesn't work for some inputs.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Add I2C slave reset via GPIO upon initialization. One user,
Michael <msd4824@yahoo.com>, has reported this allows his HVR-1600 EEPROM to
be consistently recognized when using (long,) 100 msec delays. The delays in
this commit are nominal (10 & 40 msec) and need testing/tuning on boards with
I2C problems to find the right values.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a fix for the case when a digital capture from dvr0 happens first after
modprobe, before access to any cx18 v4l2 device nodes. The initial dvb feed
start has been changed to load the firmware if not already loaded. Also fixed a
use counter to correct dvb feed accounting if starting the transport DMA fails.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the cx18-cards.c structures for the HVR-1600 to reflect that audio Line In 2
and FM radio audio go to AIN3 and AIN4 of the CS5345 mux respectively. Verified
by physical inspection of an HVR-1600MCE, by listening to FM broadcasts with the
HVR-1600MCE, and by comparing with the card definition for a PVR-150 in ivtv.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the cx18-av-core code so that accesses to cx23418 av core that
cause auto-configuration will be adjusted to emulate the auto-configuration
behavior of the cx25843. This fixes the VBI displayed as video at the top of
the frame for NTSC and probably other things.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The automatic Kconfig selection for tuners and frontends should be
conditional, based on !DVB_FE_CUSTOMISE.
This patch corrects the selection for VIDEO_CX18 on
MEDIA_TUNER_MXL5005S and DVB_S5H1409
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the current modulation and frequency is already set to
the desired parameters, then don't re-tune.
Don't store current frequency until after we've tuned successfully.
Force a re-tune after resume from standby.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the umt-010 driver the struct umt_properties sets the number of URBs for
transfer to 20. But in dvb-usb.h MAX_NO_URBS_FOR_DATA_STREAM is set to 10.
Not surprisingly this causes an oops for all devices which use the umt-010
chipset when they are inserted.
fix on Kaffeine channel scan for
Initialize stream count using MAX_NO_URBS_FOR_DATA_STREAM.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Devices can either be class devices or bus devices, not both at the
same time. Soc-camera host devices usually have a platform device as
their parent. Trying to also register them with a class crashes the
kernel, when linked statically. Interestingly, it works when built
as a module. Thanks to Paulius Zaleckas for reporting.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
platform_get_irq() returns a negative value on error, not 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Having the thermometer on during channel configuration
could cause tuning instability.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The TDA18271HD/C1 rf_cal map lookup is expected to go out of range outside
of the frequency window 41 MHz - 61.1 MHz. In these cases, the internal
RF tracking filters calibration mechanism is used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IF notch bit gets unset when we update the Main Post Div register
value, before we have a chance to write the desired IF notch setting
to the tuner. Move the IF notch configuration to after we update MPD.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When an error occurs at firmware loading, sometimes, tda1004x stops answering.
Instead of reporting such error, attach code were assuming that the device were
answering an invalid ID (0xff). This can be seen when enabling debug options:
tda1004x: tda1004x_read_byte: reg=0x0
tda1004x: tda1004x_read_byte: error reg=0x0, ret=-5
Now, instead of reporting an invalid ID, it will report the correct error:
tda10046: chip is not answering. Giving up.
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
A possible improvement would be trying to reset the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A fresh copy of v.29 firmware, using get_firmware, is leading to an invalid
firmware:
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision ff -- invalid
tda1004x: trying to boot from eeprom
tda1004x: found firmware revision ff -- invalid
tda1004x: waiting for firmware upload...
tda1004x: Error during firmware upload
tda1004x: found firmware revision ff -- invalid
tda1004x: firmware upload failed
Sometimes, loading/unloading this firmware makes tda1004x to return an invalid
ID. However, there were no printk messages to help to identify what were the
cause for the error.
With this patch, it will now print:
Invalid tda1004x ID = 0xff. Can't proceed
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
Tested with LifeView FlyDVB-T Hybrid Cardbus/MSI TV @nywhere A/D NB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Describe exactly that only s-video and composite input are working on Avermedia
A700
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
decrementing dev->empress_users should be done as last action of ts_release,
because it sleeps and write access to dev->empress_started is not protected
in any way
(additionally closing thread could mute audio after opening thread unmuted it)
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-audio.c
em28xx-dvb.c
- Em28xx extensions should ensure they are being only loaded against devices
that support them. Deals with case where there are multiple em28xx
devices, some of which have DVB (or ALSA) support and some do not.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c
- DVB support is supposed to be enabled for the first generation HVR-900.
This device was confirmed with DVB by mkrufky when we did the original work
in April, but I guess we forgot to set the flag.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-video.c
- Properly handle loading of the module when multiple devices are already
connected (such as at bootup). Before we were only calling dvb_init()
against the last device in the list, so while we were handling subsequent
adds properly, if there were multiple devices present on driver load,
everybody except the last device would not get initialized.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18-cards.h had a copy of the audio and video input enums
from cx18-av-core.h, but with different prefixes. Removed
that copy and used the ones from cx18-av-core.h.
Thanks to Andy Walls <awalls@radix.net> for the report.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The S-Video LUMA input was restricted to the In1-In4 inputs, but it
turns out that it can use the full range of In1-In8.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to timf <timf@iinet.net.au> and Mike Galbraith <efault@gmx.de> to report
this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Put explicit lock_kernel() calls into videodev_open(). That function
itself seems OK, but one never knows about all the open() functions
provided by underlying video drivers.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Check that tda827x_config is defined before attempting to use it.
Signed-off-by: Sigmund Augdal <sigmund@snap.tv>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On the TDA18271HD/C1, we perform RF tracking filter correction for VHF low
band, only. If supplied a frequency out of range, the error must be returned
to the caller (tda18271c1_rf_tracking_filter_calibration) so that it can
decide whether or not to write to register EB14, RFC_CPROG[7:0]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Testing whether xceive_pin is non-zero is not good enough as 0 is a valid
value. Instead explicitly test whether the Xceive tuner is used.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is patch for fix data structure in querycap syscall.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
-tip testing found the following build failure:
LD .tmp_vmlinux1
drivers/built-in.o: In function `generic_set_freq':
tuner-xc2028.c:(.text+0xbd896): undefined reference to `request_firmware'
tuner-xc2028.c:(.text+0xbdd7a): undefined reference to `release_firmware'
drivers/built-in.o: In function `xc_load_fw_and_init_tuner':
xc5000.c:(.text+0xc68e6): undefined reference to `request_firmware'
xc5000.c:(.text+0xc6abe): undefined reference to `release_firmware'
with this config:
http://redhat.com/~mingo/misc/config-Tue_May_20_18_11_34_CEST_2008.bad
the reason is another kconfig tool bug that has to be worked around in
the driver's Kconfig file: if FW_LOADER is selected in a second
dependency, that is not properly propagated up the dependencies.
in this case, FW_LOADER is selected from MEDIA_TUNER_XC2028:
config MEDIA_TUNER_XC2028
tristate "XCeive xc2028/xc3028 tuners"
depends on VIDEO_MEDIA && I2C
depends on HOTPLUG
select FW_LOADER
which got selected by MEDIA_TUNER:
config MEDIA_TUNER
tristate
default VIDEO_MEDIA && I2C
depends on VIDEO_MEDIA && I2C
select FW_LOADER if !MEDIA_TUNER_CUSTOMIZE && HOTPLUG
but the kconfig tool did not pick up this second-order dependency and
allowed CONFIG_FW_LOADER=m to be selected - in which case the build
fails.
the workaround i found was to move the select of FW_LOADER one level up,
so that the buggy kconfig tool can notice it and can act appropriately.
This problem can probably be worked around in other ways as well, i went
for the minimal fix.
Obviously, the kconfig tool should be fixed, it is not reasonable to
expect driver authors to do manual dependency resolution (that kconfig
itself already does) and uglify the Kconfig files. The kconfig tool did
nothing to warn about this situation and did not prevent this faulty
.config from being constructed.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
direct dereferencing from user-supplied address
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Endianness annotations and fixes + fixing the handling of
->uncorrected_block_count
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use a standard method to manage multiple instances of a hybrid tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Create a macro to report the number of instances of the tuner driver
currently in use. This will allow drivers to perform specific cleanups
before destroying the last instance of a tuner.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The gpio_dir/val statics cannot be global, they are card-specific.
Thanks to Andy Walls for pointing this out.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I always assumed that the Compro H900 could do digital as well,
but it turned out that it is an analog-only card.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The HVR-1600 can do both analog and digital capture at the same time.
Due to a driver bug -EBUSY would be returned when attempting to setup an
analog capture while a digital capture was already in progress.
Separate the two internally.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The handling of the audio registers 808 and 80c were based on old datasheets.
Updated to the latest information.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner_warn() macro relies on the local variable "priv" to be a valid
pointer. There was a case in simple_tuner_attach() where this cannot be the
case yet, so tuner_warn() would dereference a NULL "priv" pointer. Changed
the tuner_warn() to a printk() with the originally intended output format.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This code is irrelevant to this driver and should be removed. This was
copied from a hack in cx88-dvb.c, which prevents noise coming from the
analog tuner (via an audio patch cable from the pci card to the sound
hardware) when in digital mode by muting the tda988x. This issue does
not apply to this USB hybrid chip design, where a single piece of
silicon handles both analog and digital demodulation.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
somebody forgot to to fix this header...
Thanks to Ingo Molnar for pointing this out.
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
testing of the -tip tree found the following build failures on
2.6.26-rc3:
drivers/built-in.o: In function `ttusb_dec_disconnect':
ttusb_dec.c:(.text+0xa2c95): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `dvb_usb_read_remote_control':
dvb-usb-remote.c:(.text+0xa6a94): undefined reference to `input_event'
with this config:
http://redhat.com/~mingo/misc/config-Tue_May_20_03_48_57_CEST_2008.bad
these are due to the media/dvb/usb layer having dependencies on INPUT
functionality, without having that spelled out in the Kconfig file.
this patch makes that dependency explicit (for the drivers affected),
which solves the build error.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After commit 039d40019f
(V4L/DVB (7898): Fix VIDEO_MEDIA Kconfig logic)
VIDEO_MEDIA is no longer usable in Makefile's for deciding
which directories we enter, resulting in compile errors like the
following with CONFIG_VIDEO_DEV=y, CONFIG_DVB_CORE=m:
<-- snip -->
...
MODPOST 187 modules
...
make[2]: *** [__modpost] Error 1
<-- snip -->
The easiest solution is to always enter video/
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It doesn't seem to be intended that "tuner_modu_type" and
"MXL5005_ControlName" were global variables.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
check_v4l2 always returns 0, so this change is an noop for now,
but a comment says it will return something else in the future
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
change check_mode and set_mode to return negative errors and fix all callers
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
locking-add-typecheck-on-irqsave-and-friends-for-correct-flags.patch will cause
drivers/media/video/zoran_driver.c: In function 'zoran_close_end_session':
drivers/media/video/zoran_driver.c:1172: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner driver used to change i2c_client.name for its own needs, but
it really shouldn't, as this field is used by i2c-core to do the
device/driver matching. So, create and use a separate field for the
tuner driver needs.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
vidiocgmbuf() does this:
mutex_lock(&fh->cap.vb_lock);
retval = videobuf_mmap_setup(&fh->cap, gbuffers, gbufsize,
V4L2_MEMORY_MMAP);
and videobuf_mmap_setup() then just does
mutex_lock(&q->vb_lock);
ret = __videobuf_mmap_setup(q, bcount, bsize, memory);
mutex_unlock(&q->vb_lock);
which is an obvious double-take deadlock.
This patch fixes this by having vidiocgmbuf() just call the
__videobuf_mmap_setup function instead.
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reported-by: Koos Vriezen <koos.vriezen@gmail.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c/max6875: Really prevent 24RF08 corruption
i2c-amd756: Fix functionality flags
i2c: Kill the old driver matching scheme
i2c: Convert remaining new-style drivers to use module aliasing
i2c: Switch pasemi to the new device/driver matching scheme
i2c: Clean up Blackfin BF527 I2C device declarations
i2c-nforce2: Disable the second SMBus channel on the DFI Lanparty NF4 Expert
i2c: New co-maintainer
Update all the remaining new-style i2c drivers to use standard module
aliasing instead of the old driver_name/type driver matching scheme.
Note that the tuner driver is a bit quirky at the moment, as it
overwrites i2c_client.name with arbitrary strings. We write "tuner"
back on remove, to make sure that driver cycling will work properly,
but there may still be troublesome corner cases.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As reported by Ingo Molnar:
x86.git testing found the following build failure:
drivers/built-in.o: In function `pvr2_dvb_feed_thread':
pvrusb2-dvb.c:(.text+0x127e78): undefined reference to `dvb_dmx_swfilter'
drivers/built-in.o: In function `pvr2_dvb_adapter_exit':
pvrusb2-dvb.c:(.text+0x128357): undefined reference to `dvb_net_release'
pvrusb2-dvb.c:(.text+0x12836f): undefined reference to `dvb_dmxdev_release'
[...]
with this config:
CONFIG_VIDEO_PVRUSB2=y
CONFIG_DVB_CORE=m
i.e. pvrusb2 is built-in, dvb-core is modular.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- MEDIA_ATTACH now applies also for V4L;
- select a FW_LOADER dependent driver should happen only if HOTPLUG;
- apply the common tuner dependency to all tuners. This helps to avoid latter
issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If one of DVB_CORE or VIDEO_DEV is a module, the modules that can be used by
both DVB and V4L cores should also be a module, otherwise, it will break its
dependencies. This Kconfig logic implements the following:
CONFIG_VIDEO_DEV CONFIG_DVB_CORE CONFIG_VIDEO_MEDIA
N N N
N M M
N Y Y
M N M
M M M
M Y M
Y N Y
Y M M
Y Y Y
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The current code passes a context pointer in the xc5000_config struct.
This context pointer is used in the tuner_callback function, used to
reset the device after firmware download.
The xc5000_config struct is a static structure, whose .priv member was
being assigned before calling xc5000_attach(). If there are more than
one of the same device type installed on a single system, the last one
to assign xc5000_config.priv will "win", and all others will cease to
function properly.
This patch passes the context pointer in xc5000_attach() rather that
storing it within the static struct xc5000_config.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Upon error conditions in cx18/ivtv_probe(), the code at the 'err:' label
leaves a NULL entry in cx18/ivtv_cards[]. This can cause a NULL pointer
de-reference in cx18/ivtv_v4l2_open() which is fixed by this patch.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tuner, S-Video and Composite are all working for the Compro H900.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
patch 779169257208 made the variable mask unnecessary.
This patch just removes the declaration.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This causes a problem with the audio mute on some cards and is done
implictly in the audio initialization code.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I was informed by Jan Hoogenraad that two people needed to be removed
from the original copyright comments.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ensure we have the correct .h dependencies included.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
4 exceptions where the code would read very ugly otherwise.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ATSC and QAM should be working but basic testing is required.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Initial check-in of the original driver to establish history.
Signed-off-by: Chia-Ling Lu Developer <chialing@realtek.com.tw>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch does some small cleanup to mt312.
It changes kconfig description to also list the ZL10313.
It does change some strange symbol names to be consistent with
module name mt312 and naming of all other functions in there.
* vp310_mt312_ops -> mt312_ops
* vp310_mt312_attach -> mt312_attach
Adds a MODULE_AUTHOR for me
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
x86.git testing found the following build bug on latest -git:
CC [M] drivers/media/video/mt9v022.o
drivers/media/video/mt9v022.c: In function 'bus_switch_request':
drivers/media/video/mt9v022.c:199: error: implicit declaration of function 'gpio_is_valid'
drivers/media/video/mt9v022.c:201: error: implicit declaration of function 'gpio_request'
drivers/media/video/mt9v022.c:207: error: implicit declaration of function 'gpio_direction_output'
drivers/media/video/mt9v022.c:211: error: implicit declaration of function 'gpio_free'
drivers/media/video/mt9v022.c: In function 'bus_switch_act':
drivers/media/video/mt9v022.c:237: error: implicit declaration of function 'gpio_set_value_cansleep'
make[2]: *** [drivers/media/video] Error 2
make[1]: *** [drivers/media] Error 2
make[1]: *** Waiting for unfinished jobs....
make: *** [drivers] Error 2
with this config:
http://redhat.com/~mingo/misc/config-Sat_May__3_16_08_39_CEST_2008.bad
the bug was that the driver uses GPIO functionality but only includes
the GPIO interface definitions for the CONFIG_MT9M001_PCA9536_SWITCH
case, which was not set in this config.
The quick fix seems to be to include linux/gpio.h unconditionally. (this
seems like a small cleanup as well as it removes and #ifdef is more
robust than an inclusion of asm/gpio.h) Not tested too much yet, so
please have another look in any case.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
itd1000_fre_values[] can become static const.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- cx18-i2c.c should #include "cx18-i2c.h" for getting the prototypes of
it's global functions
- make the following needlessly global functions static:
- cx18-fileops.c:cx18_claim_stream()
- cx18-fileops.c:cx18_release_stream()
- cx18-queue.c:cx18_queue_move()
- remove the following unused functions:
- cx18-driver.c:cx18_waitq()
- cx18-queue.c:cx18_buf_copy_from_user()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- don't show kernel backtrace when the allocation of the buffers fails: the
normal ivtv/cx18 messages are clear enough and the backtrace scares users.
- fix cleanup after the buffer allocation fails (caused kernel panic).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix compile warnings if MODULE is not defined.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since:
1) FW_LOADER is defined as:
config FW_LOADER
tristate "Userspace firmware loading support"
depends on HOTPLUG
2) several V4L/DVB driver just selects it;
3) select is not smart enough to auto-select HOTPLUG, if select FW_LOADER.
So, All drivers that select FW_LOADER should also depend on HOTPLUG.
An easier solution (for the end-user perspective) would be to "select HOTPLUG".
However, live is not simple. This would cause recursive dependency issues like
this one:
drivers/usb/Kconfig:62:error: found recursive dependency: USB -> USB_OHCI_HCD
-> I2C -> MEDIA_TUNER -> MEDIA_TUNER_XC2028 -> HOTPLUG -> PCCARD -> PCMCIA ->
USB_ARCH_HAS_HCD -> MOUSE_APPLETOUCH -> USB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx88 doesn't need support for FW_LOADER. Instead, this is required only for
cx88-blackbird.
Also, cx88-blackbird depends on HOTPLUG, due to FW_LOADER dependency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-dvb doesn't need FW_LOADER. Instead, tuner-xc2028 needs to select
FW_LOADER.
Also, this can happen only if HOTPLUG is selected, since FW_LOADER
is dependent on HOTPLUG.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since all tuners are dependent of I2C, move I2C dependency to MEDIA_TUNER.
Also, simplifies the dependencies for the other Kconfig items.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDEO_TUNER is responsible for compilation of tuners.ko module. This were the
previous behaviour before the creation of MEDIA_TUNER.
Before this patch, tuner.ko were created even for drivers that don't need a
tuner (like webcam drivers).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only show debug from tda18271_set_standby_mode if DBG_ADV is set.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Abort rf band calibration loop for the TDA18271HD/C2 if an error is detected.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
x86.git testing found the following build bug in v2.6.26-rc1:
drivers/built-in.o: In function `cinergyt2_probe':
cinergyT2.c:(.text+0xb6117): undefined reference to `input_allocate_device'
cinergyT2.c:(.text+0xb6230): undefined reference to `input_register_device'
cinergyT2.c:(.text+0xb623d): undefined reference to `input_free_device'
with the following config:
http://redhat.com/~mingo/misc/config-Sun_May__4_22_06_54_CEST_2008.bad
The reason for the bug is that the cinergyT2 driver depends on
CONFIG_INPUT functionality, but if INPUT is modular it's still possible
to build CONFIG_DVB_CINERGYT2=y - which leads to missing symbols.
The solution is to make DVB_CINERGYT2 dependent on INPUT.
[ This solves the build problem - i have not tested the driver on this card. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix undefined references in au0828:
depends on USB and select VIDEO_TVEEPROM
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
x86.git testing found the following build failure in v2.6.26-rc1:
MODPOST 424 modules
ERROR: "tveeprom_hauppauge_analog" [drivers/media/video/au0828/au0828.ko] undefined!
ERROR: "tveeprom_read" [drivers/media/video/au0828/au0828.ko] undefined!
with this config:
http://redhat.com/~mingo/misc/config-Sat_May__3_22_28_58_CEST_2008.bad
this patch does what other video drivers do to utilize the
VIDEO_TVEEPROM functionality (and this resolves the build problem) - but
i have not checked it on real hardware and i have not checked whether
the fix is complete.
selections, so some items might still be missing - just not triggered
with this specific config.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following build error:
drivers/built-in.o: In function `xc_load_fw_and_init_tuner':
xc5000.c:(.text+0x2dacd): undefined reference to `request_firmware'
xc5000.c:(.text+0x2daf0): undefined reference to `release_firmware'
xc5000.c:(.text+0x2db85): undefined reference to `release_firmware'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change addresses kernel bug #10459: In kernel 2.6.25 the
budget_av driver polls for an CI slot in 100ms intervals (because no
interrupt solution for budget_av cards is feasible due to HW reasons).
If no CI/CAM is connected to the DVB card, polling times out only after 250ms.
This periodic polling leads to high CPU load.
The change increases the polling interval for empty slots from 100ms to 5s.
Intervals for remaining slot states (invalid, in progress, ready) are unchanged,
as they are either temporary conditions or no timeout should occur.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx23885 driver used to use dvb-pll for LG-TDVS-H064F support on the
FusionHDTV5 Express. This has since been converted to use tuner-simple
instead, once digital tuning support was added to tuner-simple.
Since cx23885 no longer uses dvb-pll, remove the #include "dvb-pll.h",
and the DVB_PLL Kconfig selection.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
