Add support for AMD PTDMA controller. It performs high-bandwidth
memory to memory and IO copy operation. Device commands are managed
via a circular queue of 'descriptors', each of which specifies source
and destination addresses for copying a single buffer of data.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Link: https://lore.kernel.org/r/1629208559-51964-2-git-send-email-Sanju.Mehta@amd.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for dsa_drv compat support to be built-in, move the bus
code to its own compilation unit. A follow-on patch adds the compat
implementation. Recall that the compat implementation allows for the
deprecated / omnibus dsa_drv binding scheme rather than the idiomatic
organization of a full fledged bus driver per driver type.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/162637468142.744545.2811632736881720857.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20210120131859.2056308-3-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Cc: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120131859.2056308-2-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add DMA controller driver for Lightning Mountain (LGM) family of SoCs.
The main function of the DMA controller is the transfer of data from/to any
peripheral to/from the memory. A memory to memory copy capability can also
be configured.
This ldma driver is used for configure the device and channnels for data
and control paths.
Signed-off-by: Amireddy Mallikarjuna reddy <mallikarjunax.reddy@linux.intel.com>
Link: https://lore.kernel.org/r/5fc54eb7ccfad4f8dd812b66b884054fc55cf050.1606905330.git.mallikarjunax.reddy@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch removes the MIC drivers from the kernel tree
since the corresponding devices have been discontinued.
Removing the dma and char-misc changes in one patch and
merging via the char-misc tree is best to avoid any
potential build breakage.
Cc: Nikhil Rao <nikhil.rao@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/8c1443136563de34699d2c084df478181c205db4.1603854416.git.sudeep.dutt@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds external DMA controller driver implemented in Socionext
UniPhier SoCs. This driver supports DMA_MEMCPY and DMA_SLAVE modes.
Since this driver does not support the the way to transfer size
unaligned to burst width, 'src_maxburst' or 'dst_maxburst' of
dma_slave_config must be 1 to transfer arbitrary size. If transfer
size is unaligned to burst size, the transfer isn't started and
the driver displays an error message.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1582271550-3403-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds a driver for HiSilicon Kunpeng DMA engine. This DMA engine
which is an PCIe iEP offers 30 channels, each channel has a send queue, a
complete queue and an interrupt to help to do tasks. This DMA engine can do
memory copy between memory blocks or between memory and device buffer.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Zhenfa Qiu <qiuzhenfa@hisilicon.com>
Link: https://lore.kernel.org/r/1579155057-80523-1-git-send-email-wangzhou1@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The idxd driver introduces the Intel Data Stream Accelerator [1] that will
be available on future Intel Xeon CPUs. One of the kernel access
point for the driver is through the dmaengine subsystem. It will initially
provide the DMA copy service to the kernel.
Some of the main functionality introduced with this accelerator
are: shared virtual memory (SVM) support, and descriptor submission using
Intel CPU instructions movdir64b and enqcmds. There will be additional
accelerator devices that share the same driver with variations to
capabilities.
This commit introduces the probe and initialization component of the
driver.
[1]: https://software.intel.com/en-us/download/intel-data-streaming-accelerator-preliminary-architecture-specification
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/157965023991.73301.6186843973135311580.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some PLX Switches can expose DMA engines via extra PCI functions
on the upstream port. Each function will have one DMA channel.
This patch is just the core PCI driver skeleton and dma
engine registration.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20200103212021.2881-2-logang@deltatee.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver for Socionext Milbeaut HDMAC controller. The controller has
upto 8 floating channels, that need a predefined slave-id to work
from a set of slaves.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Link: https://lore.kernel.org/r/20191015033359.14925-1-jassisinghbrar@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DPPA2(Data Path Acceleration Architecture 2) qDMA supports
virtualized channel by allowing DMA jobs to be enqueued into
different work queues. Core can initiate a DMA transaction by
preparing a frame descriptor(FD) for each DMA job and enqueuing
this job through a hardware portal. DPAA2 components can also
prepare a FD and enqueue a DMA job through a hardware portal.
The qDMA prefetches DMA jobs through DPAA2 hardware portal. It
then schedules and dispatches to internal DMA hardware engines,
which generate read and write requests. Both qDMA source data and
destination data can be either contiguous or non-contiguous using
one or more scatter/gather tables.
The qDMA supports global bandwidth flow control where all DMA
transactions are stalled if the bandwidth threshold has been reached.
Also supported are transaction based read throttling.
Add NXP dppa2 qDMA to support some of Layerscape SoCs.
such as: LS1088A, LS208xA, LX2, etc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20190930020440.7754-2-peng.ma@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The newer and better JZ4780 driver is now used to provide DMA
functionality on the JZ4740.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Add Synopsys PCIe Endpoint eDMA IP core driver to kernel.
This IP is generally distributed with Synopsys PCIe Endpoint IP (depends
of the use and licensing agreement).
This core driver, initializes and configures the eDMA IP using vma-helpers
functions and dma-engine subsystem.
This driver can be compile as built-in or external module in kernel.
To enable this driver just select DW_EDMA option in kernel configuration,
however it requires and selects automatically DMA_ENGINE and
DMA_VIRTUAL_CHANNELS option too.
In order to transfer data from point A to B as fast as possible this IP
requires a dedicated memory space containing linked list of elements.
All elements of this linked list are continuous and each one describes a
data transfer (source and destination addresses, length and a control
variable).
For the sake of simplicity, lets assume a memory space for channel write
0 which allows about 42 elements.
+---------+
| Desc #0 |-+
+---------+ |
V
+----------+
| Chunk #0 |-+
| CB = 1 | | +----------+ +-----+ +-----------+ +-----+
+----------+ +->| Burst #0 |->| ... |->| Burst #41 |->| llp |
| +----------+ +-----+ +-----------+ +-----+
V
+----------+
| Chunk #1 |-+
| CB = 0 | | +-----------+ +-----+ +-----------+ +-----+
+----------+ +->| Burst #42 |->| ... |->| Burst #83 |->| llp |
| +-----------+ +-----+ +-----------+ +-----+
V
+----------+
| Chunk #2 |-+
| CB = 1 | | +-----------+ +-----+ +------------+ +-----+
+----------+ +->| Burst #84 |->| ... |->| Burst #125 |->| llp |
| +-----------+ +-----+ +------------+ +-----+
V
+----------+
| Chunk #3 |-+
| CB = 0 | | +------------+ +-----+ +------------+ +-----+
+----------+ +->| Burst #126 |->| ... |->| Burst #129 |->| llp |
+------------+ +-----+ +------------+ +-----+
Legend:
- Linked list, also know as Chunk
- Linked list element*, also know as Burst *CB*, also know as Change Bit,
it's a control bit (and typically is toggled) that allows to easily
identify and differentiate between the current linked list and the
previous or the next one.
- LLP, is a special element that indicates the end of the linked list
element stream also informs that the next CB should be toggle
On every last Burst of the Chunk (Burst #41, Burst #83, Burst #125 or
even Burst #129) is set some flags on their control variable (RIE and
LIE bits) that will trigger the send of "done" interruption.
On the interruptions callback, is decided whether to recycle the linked
list memory space by writing a new set of Bursts elements (if still
exists Chunks to transfer) or is considered completed (if there is no
Chunks available to transfer).
On scatter-gather transfer mode, the client will submit a scatter-gather
list of n (on this case 130) elements, that will be divide in multiple
Chunks, each Chunk will have (on this case 42) a limited number of
Bursts and after transferring all Bursts, an interrupt will be
triggered, which will allow to recycle the all linked list dedicated
memory again with the new information relative to the next Chunk and
respective Burst associated and repeat the whole cycle again.
On cyclic transfer mode, the client will submit a buffer pointer, length
of it and number of repetitions, in this case each burst will correspond
directly to each repetition.
Each Burst can describes a data transfer from point A(source) to point
B(destination) with a length that can be from 1 byte up to 4 GB. Since
dedicated the memory space where the linked list will reside is limited,
the whole n burst elements will be organized in several Chunks, that
will be used later to recycle the dedicated memory space to initiate a
new sequence of data transfers.
The whole transfer is considered has completed when it was transferred
all bursts.
Currently this IP has a set well-known register map, which includes
support for legacy and unroll modes. Legacy mode is version of this
register map that has multiplexer register that allows to switch
registers between all write and read channels and the unroll modes
repeats all write and read channels registers with an offset between
them. This register map is called v0.
The IP team is creating a new register map more suitable to the latest
PCIe features, that very likely will change the map register, which this
version will be called v1. As soon as this new version is released by
the IP team the support for this version in be included on this driver.
According to the logic, patches 1, 2 and 3 should be squashed into 1
unique patch, but for the sake of simplicity of review, it was divided
in this 3 patches files.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
NXP Queue DMA controller(qDMA) on Layerscape SoCs supports channel
virtuallization by allowing DMA jobs to be enqueued into different
command queues.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Jiaheng Fan <jiaheng.fan@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The MIO DMAC (Media IO DMA Controller) is used in UniPhier LD4,
Pro4, and sLD8 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds support for ColdFire mcf5441x-family edma
module.
The ColdFire edma module is slightly different from fsl-edma,
so a new driver is added. But most of the code is common
between fsl-edma and mcf-edma so it has been collected into a
separate common module fsl-edma-common (patch 1/3).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds a new fsl-edma-common module to allow new
mcf-edma module code to use most of the fsl-edma code.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
MediaTek High-Speed DMA controller (HSDMA) on MT7622 and MT7623 SoC has
a single ring is dedicated to memory-to-memory transfer through ring based
descriptor management.
Even though there is only one physical ring available inside HSDMA, the
driver can be easily extended to the support of multiple virtual channels
processing simultaneously by means of DMA_VIRTUAL_CHANNELS effort.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the DW AXI DMAC controller.
DW AXI DMAC is a part of HSDK development board from Synopsys.
In this driver implementation only DMA_MEMCPY transfers are
supported.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Updates for this cycle include:
- New driver for Spreadtrum dma controller, ST MDMA and DMAMUX controllers
- PM support for IMG MDC drivers
- Updates to bcm-sba-raid driver and improvements to sun6i driver
- Subsystem conversion for:
- timers to use timer_setup()
- remove usage of PCI pool API
- usage of %p format specifier
- Minor updates to bunch of drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t9Ix
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.15-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"Updates for this cycle include:
- new driver for Spreadtrum dma controller, ST MDMA and DMAMUX
controllers
- PM support for IMG MDC drivers
- updates to bcm-sba-raid driver and improvements to sun6i driver
- subsystem conversion for:
- timers to use timer_setup()
- remove usage of PCI pool API
- usage of %p format specifier
- minor updates to bunch of drivers"
* tag 'dmaengine-4.15-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (49 commits)
dmaengine: ti-dma-crossbar: Correct am335x/am43xx mux value type
dmaengine: dmatest: warn user when dma test times out
dmaengine: Revert "rcar-dmac: use TCRB instead of TCR for residue"
dmaengine: stm32_mdma: activate pack/unpack feature
dmaengine: at_hdmac: Remove unnecessary 0x prefixes before %pad
dmaengine: coh901318: Remove unnecessary 0x prefixes before %pad
MAINTAINERS: Step down from a co-maintaner of DW DMAC driver
dmaengine: pch_dma: Replace PCI pool old API
dmaengine: Convert timers to use timer_setup()
dmaengine: sprd: Add Spreadtrum DMA driver
dt-bindings: dmaengine: Add Spreadtrum SC9860 DMA controller
dmaengine: sun6i: Retrieve channel count/max request from devicetree
dmaengine: Build bcm-sba-raid driver as loadable module for iProc SoCs
dmaengine: bcm-sba-raid: Use common GPL comment header
dmaengine: bcm-sba-raid: Use only single mailbox channel
dmaengine: bcm-sba-raid: serialize dma_cookie_complete() using reqs_lock
dmaengine: pl330: fix descriptor allocation fail
dmaengine: rcar-dmac: use TCRB instead of TCR for residue
dmaengine: sun6i: Add support for Allwinner A64 and compatibles
arm64: allwinner: a64: Add devicetree binding for DMA controller
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the DMA controller driver for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the driver for the STM32 MDMA controller.
Master Direct memory access (MDMA) is used in order to provide high-speed
data transfer between memory and memory or between peripherals and memory.
MDMA controller provides a master AXI interface for main memory and
peripheral registers access (system access port) and a master AHB
interface only for Cortex-M7 TCM memory access (TCM access port).
MDMA works in conjunction with the standard DMA controllers (DMA1 or DMA2).
It offers up to 64 channels, each dedicated to managing memory access
requests from one of the DMA stream memory buffer or other peripherals
(w/ integrated FIFO).
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch implements the STM32 DMAMUX driver.
The DMAMUX request multiplexer allows routing a DMA request line between
the peripherals and the DMA controllers of the product. The routing
function is ensured by a programmable multi-channel DMA request line
multiplexer. Each channel selects a unique DMA request line,
unconditionally or synchronously with events from its DMAMUX
synchronization inputs. The DMAMUX may also be used as a DMA request
generator from programmable events on its input trigger signals
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This driver adds support for the Altera / Intel modular Scatter-Gather
Direct Memory Access (mSGDMA) intellectual property (IP) to the Linux
DMAengine subsystem. Currently it supports the following op modes:
- DMA_MEMCPY
- DMA_SG
- DMA_SLAVE
This implementation has been tested on an Altera Cyclone FPGA connected
via PCIe, both on an ARM and an x86 platform.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Broadcom stream buffer accelerator (SBA) provides offloading
capabilities for RAID operations. This SBA offload engine is
accessible via Broadcom SoC specific ring manager.
This patch adds Broadcom SBA RAID driver which provides one
DMA device with RAID capabilities using one or more Broadcom
SoC specific ring manager channels. The SBA RAID driver in its
current shape implements memcpy, xor, and pq operations.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
ZTE ZX dma driver is not ZX296702 specific. It works for not only
ZX296702 but also other ZTE ZX family platforms like ZX296718. Let's
rename the file to reflect that.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the Flexible Direct Memory Access (FDMA) core
driver. The FDMA is a slim core CPU with a dedicated firmware.
It is a general purpose DMA controller capable of supporting 16
independent DMA channels. Data moves maybe from memory to memory
or between memory and paced latency critical real time targets and it
is found on al STi based chipsets.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The new mv_xor_v2 driver supports the XOR engines found in the 64-bits
ARM from Marvell of the Armada 7K and Armada 8K family. This XOR
engine is a completely new hardware block, entirely different from the
one used on previous Marvell Armada platforms, which use the existing
mv_xor driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for the Tegra210 Audio DMA controller that is used for
transferring data between system memory and the Audio sub-system.
The driver only supports cyclic transfers because this is being solely
used for audio.
This driver is based upon the work by Dara Ramesh <dramesh@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Creating a QCOM directory for all QCOM DMA source files.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the STM32 DMA controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
the symbol CONFIG_IDMA64 should rather be CONFIG_INTEL_IDMA64 to conform to
rest of the intel dmaengine drivers. This was found after sorting the
entries and trying to place this odd one
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This time we have aded a new capability for scatter-gathered memset using
dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Others
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2 which is
deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gQZ6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have aded a new capability for scatter-gathered memset
using dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Other:
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2
which is deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers"
[ The Kconfig and Makefile entries got re-sorted alphabetically, and I
handled the conflict with the new Intel integrated IDMA driver by
slightly mis-sorting it on purpose: "IDMA64" got sorted after "IMX" in
order to keep the Intel entries together. I think it might be a good
idea to just rename the IDMA64 config entry to INTEL_IDMA64 to make
the sorting be a true sort, not this mismash.
Also, this merge disables the COMPILE_TEST for the sun4i DMA
controller, because it does not compile cleanly at all. - Linus ]
* tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (89 commits)
dmaengine: ioatdma: add Broadwell EP ioatdma PCI dev IDs
dmaengine :ipu: change ipu_irq_handler() to remove compile warning
dmaengine: ioatdma: Fix variable array length
dmaengine: ioatdma: fix sparse "error" with prep lock
dmaengine: hdmac: Add memset capabilities
dmaengine: sort the sh Makefile
dmaengine: sort the sh Kconfig
dmaengine: sort the dw Kconfig
dmaengine: sort the Kconfig
dmaengine: sort the makefile
drivers/dma: make mv_xor.c driver explicitly non-modular
dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller
devicetree: Add bindings documentation for Analog Devices AXI-DMAC
dmaengine: xgene-dma: Fix the lock to allow client for further submission of requests
dmaengine: ioatdma: fix coccinelle warning
dmaengine: ioatdma: fix zero day warning on incompatible pointer type
dmaengine: tegra-apb: Simplify locking for device using global pause
dmaengine: tegra-apb: Remove unnecessary return statements and variables
dmaengine: tegra-apb: Avoid unnecessary channel base address calculation
dmaengine: tegra-apb: Remove unused variables
...
dmaengine makefile grew over the years, unfortunately without any
order to it. So order by core, dmatest and driver sections and
sort these sections alphabetically
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for the Analog Devices AXI-DMAC DMA controller. This controller
is a soft peripheral that can be instantiated in a FPGA and is often used
in Analog Devices' reference designs for FPGA platforms.
The peripheral has various configuration options that can be selected at
synthesis time and influence the supported features of the instantiated
peripheral, those options are represented as device-tree properties to
allow the driver to behave accordingly.
The peripheral has a zero latency architecture, which means it is possible
to switch from one to the next descriptor without any delay. This is
archived by having a internal queue which can hold multiple descriptors.
The driver supports this, which means it will submit new descriptors
directly to the hardware until the queue is full and not wait for a
descriptor to complete before the next one is submitted. Interrupts are
used for the descriptor queue flow control.
Currently the driver supports SG, cyclic and interleaved slave DMA.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the DMA engine present on Allwinner A10,
A13, A10S and A20 SoCs. This engine has two kinds of channels: normal
and dedicated. The main difference is in the mode of operation;
while a single normal channel may be operating at any given time,
dedicated channels may operate simultaneously provided there is no
overlap of source or destination.
Hardware documentation can be found on A10 User Manual (section 12), A13
User Manual (section 14) and A20 User Manual (section 1.12)
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for DMA on NXP LPC18xx/43xx platforms which has
a multiplexer in front of the PL080 dma request lines.
The mux is a single register in the LPC18xx/43xx CREG block
and can multiplex up to 4 request lines to each of the 16
lines on the PL080.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Intel integrated DMA (iDMA) 64-bit is a specific IP that is used as a part of
LPSS devices such as HSUART or SPI. The iDMA IP is attached for private
usage on each host controller independently.
While it has similarities with Synopsys DesignWare DMA, the following
distinctions doesn't allow to use the existing driver:
- 64-bit mode with corresponding changes in Hardware Linked List data structure
- many slight differences in the channel registers
Moreover this driver is based on the DMA virtual channels framework that helps
to make the driver cleaner and easy to understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>